blob: d9293c57f573c0534adb777f88efad95e5da6c85 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0-only
%YAML 1.2
---
$id: http://devicetree.org/schemas/i2c/snps,designware-i2c.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Synopsys DesignWare APB I2C Controller
maintainers:
- Jarkko Nikula <jarkko.nikula@linux.intel.com>
allOf:
- $ref: /schemas/i2c/i2c-controller.yaml#
- if:
properties:
compatible:
not:
contains:
const: mscc,ocelot-i2c
then:
properties:
reg:
maxItems: 1
properties:
compatible:
oneOf:
- description: Generic Synopsys DesignWare I2C controller
const: snps,designware-i2c
- description: Microsemi Ocelot SoCs I2C controller
items:
- const: mscc,ocelot-i2c
- const: snps,designware-i2c
- description: Baikal-T1 SoC System I2C controller
const: baikal,bt1-sys-i2c
reg:
minItems: 1
items:
- description: DW APB I2C controller memory mapped registers
- description: |
ICPU_CFG:TWI_DELAY registers to setup the SDA hold time.
This registers are specific to the Ocelot I2C-controller.
interrupts:
maxItems: 1
clocks:
minItems: 1
items:
- description: I2C controller reference clock source
- description: APB interface clock source
clock-names:
minItems: 1
items:
- const: ref
- const: pclk
resets:
maxItems: 1
clock-frequency:
description: Desired I2C bus clock frequency in Hz
enum: [100000, 400000, 1000000, 3400000]
default: 400000
i2c-sda-hold-time-ns:
description: |
The property should contain the SDA hold time in nanoseconds. This option
is only supported in hardware blocks version 1.11a or newer or on
Microsemi SoCs.
i2c-scl-falling-time-ns:
description: |
The property should contain the SCL falling time in nanoseconds.
This value is used to compute the tLOW period.
default: 300
i2c-sda-falling-time-ns:
description: |
The property should contain the SDA falling time in nanoseconds.
This value is used to compute the tHIGH period.
default: 300
dmas:
items:
- description: TX DMA Channel
- description: RX DMA Channel
dma-names:
items:
- const: tx
- const: rx
unevaluatedProperties: false
required:
- compatible
- reg
- interrupts
examples:
- |
i2c@f0000 {
compatible = "snps,designware-i2c";
reg = <0xf0000 0x1000>;
interrupts = <11>;
clock-frequency = <400000>;
};
- |
i2c@1120000 {
compatible = "snps,designware-i2c";
reg = <0x1120000 0x1000>;
interrupts = <12 1>;
clock-frequency = <400000>;
i2c-sda-hold-time-ns = <300>;
i2c-sda-falling-time-ns = <300>;
i2c-scl-falling-time-ns = <300>;
};
- |
i2c@2000 {
compatible = "snps,designware-i2c";
reg = <0x2000 0x100>;
#address-cells = <1>;
#size-cells = <0>;
clock-frequency = <400000>;
clocks = <&i2cclk>;
interrupts = <0>;
eeprom@64 {
compatible = "atmel,24c02";
reg = <0x64>;
};
};
- |
i2c@100400 {
compatible = "mscc,ocelot-i2c", "snps,designware-i2c";
reg = <0x100400 0x100>, <0x198 0x8>;
pinctrl-0 = <&i2c_pins>;
pinctrl-names = "default";
interrupts = <8>;
clocks = <&ahb_clk>;
};
...