blob: 2766fe45bb98b5307065ea2d79c5b9f2b13d6156 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/ethernet-phy.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Ethernet PHY Generic Binding
maintainers:
- Andrew Lunn <andrew@lunn.ch>
- Florian Fainelli <f.fainelli@gmail.com>
- Heiner Kallweit <hkallweit1@gmail.com>
# The dt-schema tools will generate a select statement first by using
# the compatible, and second by using the node name if any. In our
# case, the node name is the one we want to match on, while the
# compatible is optional.
select:
properties:
$nodename:
pattern: "^ethernet-phy(@[a-f0-9]+)?$"
required:
- $nodename
properties:
$nodename:
pattern: "^ethernet-phy(@[a-f0-9]+)?$"
compatible:
oneOf:
- const: ethernet-phy-ieee802.3-c22
description: PHYs that implement IEEE802.3 clause 22
- const: ethernet-phy-ieee802.3-c45
description: PHYs that implement IEEE802.3 clause 45
- pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$"
description:
If the PHY reports an incorrect ID (or none at all) then the
compatible list may contain an entry with the correct PHY ID
in the above form.
The first group of digits is the 16 bit Phy Identifier 1
register, this is the chip vendor OUI bits 3:18. The
second group of digits is the Phy Identifier 2 register,
this is the chip vendor OUI bits 19:24, followed by 10
bits of a vendor specific ID.
- items:
- pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$"
- const: ethernet-phy-ieee802.3-c22
- items:
- pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$"
- const: ethernet-phy-ieee802.3-c45
reg:
minimum: 0
maximum: 31
description:
The ID number for the PHY.
interrupts:
maxItems: 1
max-speed:
enum:
- 10
- 100
- 1000
- 2500
- 5000
- 10000
- 20000
- 25000
- 40000
- 50000
- 56000
- 100000
- 200000
description:
Maximum PHY supported speed in Mbits / seconds.
broken-turn-around:
$ref: /schemas/types.yaml#/definitions/flag
description:
If set, indicates the PHY device does not correctly release
the turn around line low at end of the control phase of the
MDIO transaction.
enet-phy-lane-swap:
$ref: /schemas/types.yaml#/definitions/flag
description:
If set, indicates the PHY will swap the TX/RX lanes to
compensate for the board being designed with the lanes
swapped.
eee-broken-100tx:
$ref: /schemas/types.yaml#/definitions/flag
description:
Mark the corresponding energy efficient ethernet mode as
broken and request the ethernet to stop advertising it.
eee-broken-1000t:
$ref: /schemas/types.yaml#/definitions/flag
description:
Mark the corresponding energy efficient ethernet mode as
broken and request the ethernet to stop advertising it.
eee-broken-10gt:
$ref: /schemas/types.yaml#/definitions/flag
description:
Mark the corresponding energy efficient ethernet mode as
broken and request the ethernet to stop advertising it.
eee-broken-1000kx:
$ref: /schemas/types.yaml#/definitions/flag
description:
Mark the corresponding energy efficient ethernet mode as
broken and request the ethernet to stop advertising it.
eee-broken-10gkx4:
$ref: /schemas/types.yaml#/definitions/flag
description:
Mark the corresponding energy efficient ethernet mode as
broken and request the ethernet to stop advertising it.
eee-broken-10gkr:
$ref: /schemas/types.yaml#/definitions/flag
description:
Mark the corresponding energy efficient ethernet mode as
broken and request the ethernet to stop advertising it.
phy-is-integrated:
$ref: /schemas/types.yaml#/definitions/flag
description:
If set, indicates that the PHY is integrated into the same
physical package as the Ethernet MAC. If needed, muxers
should be configured to ensure the integrated PHY is
used. The absence of this property indicates the muxers
should be configured so that the external PHY is used.
resets:
maxItems: 1
reset-names:
const: phy
reset-gpios:
maxItems: 1
description:
The GPIO phandle and specifier for the PHY reset signal.
reset-assert-us:
description:
Delay after the reset was asserted in microseconds. If this
property is missing the delay will be skipped.
reset-deassert-us:
description:
Delay after the reset was deasserted in microseconds. If
this property is missing the delay will be skipped.
sfp:
$ref: /schemas/types.yaml#/definitions/phandle
description:
Specifies a reference to a node representing a SFP cage.
rx-internal-delay-ps:
description: |
RGMII Receive PHY Clock Delay defined in pico seconds. This is used for
PHY's that have configurable RX internal delays. If this property is
present then the PHY applies the RX delay.
tx-internal-delay-ps:
description: |
RGMII Transmit PHY Clock Delay defined in pico seconds. This is used for
PHY's that have configurable TX internal delays. If this property is
present then the PHY applies the TX delay.
required:
- reg
additionalProperties: true
examples:
- |
ethernet {
#address-cells = <1>;
#size-cells = <0>;
ethernet-phy@0 {
compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c45";
interrupt-parent = <&PIC>;
interrupts = <35 1>;
reg = <0>;
resets = <&rst 8>;
reset-names = "phy";
reset-gpios = <&gpio1 4 1>;
reset-assert-us = <1000>;
reset-deassert-us = <2000>;
};
};