| # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/phy/phy-stm32-usbphyc.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: STMicroelectronics STM32 USB HS PHY controller binding |
| |
| description: |
| |
| The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI |
| switch. It controls PHY configuration and status, and the UTMI+ switch that |
| selects either OTG or HOST controller for the second PHY port. It also sets |
| PLL configuration. |
| |
| USBPHYC |
| |_ PLL |
| | |
| |_ PHY port#1 _________________ HOST controller |
| | __ | |
| | / 1|________________| |
| |_ PHY port#2 ----| |________________ |
| | \_0| | |
| |_ UTMI switch_______| OTG controller |
| |
| maintainers: |
| - Amelie Delaunay <amelie.delaunay@foss.st.com> |
| |
| properties: |
| compatible: |
| const: st,stm32mp1-usbphyc |
| |
| reg: |
| maxItems: 1 |
| |
| clocks: |
| maxItems: 1 |
| |
| resets: |
| maxItems: 1 |
| |
| "#address-cells": |
| const: 1 |
| |
| "#size-cells": |
| const: 0 |
| |
| vdda1v1-supply: |
| description: regulator providing 1V1 power supply to the PLL block |
| |
| vdda1v8-supply: |
| description: regulator providing 1V8 power supply to the PLL block |
| |
| '#clock-cells': |
| description: number of clock cells for ck_usbo_48m consumer |
| const: 0 |
| |
| #Required child nodes: |
| |
| patternProperties: |
| "^usb-phy@[0|1]$": |
| type: object |
| description: |
| Each port the controller provides must be represented as a sub-node. |
| |
| properties: |
| reg: |
| description: phy port index. |
| maxItems: 1 |
| |
| phy-supply: |
| description: regulator providing 3V3 power supply to the PHY. |
| |
| "#phy-cells": |
| enum: [ 0x0, 0x1 ] |
| |
| connector: |
| type: object |
| allOf: |
| - $ref: ../connector/usb-connector.yaml |
| properties: |
| vbus-supply: true |
| |
| # It can be necessary to adjust the PHY settings to compensate parasitics, which can be due |
| # to USB connector/receptacle, routing, ESD protection component,... Here is the list of |
| # all optional parameters to tune the interface of the PHY (HS for High-Speed, FS for Full- |
| # Speed, LS for Low-Speed) |
| |
| st,current-boost-microamp: |
| description: Current boosting in uA |
| enum: [ 1000, 2000 ] |
| |
| st,no-lsfs-fb-cap: |
| description: Disables the LS/FS feedback capacitor |
| type: boolean |
| |
| st,decrease-hs-slew-rate: |
| description: Decreases the HS driver slew rate by 10% |
| type: boolean |
| |
| st,tune-hs-dc-level: |
| description: | |
| Tunes the HS driver DC level |
| - <0> normal level |
| - <1> increases the level by 5 to 7 mV |
| - <2> increases the level by 10 to 14 mV |
| - <3> decreases the level by 5 to 7 mV |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0 |
| maximum: 3 |
| default: 0 |
| |
| st,enable-fs-rftime-tuning: |
| description: Enables the FS rise/fall tuning option |
| type: boolean |
| |
| st,enable-hs-rftime-reduction: |
| description: Enables the HS rise/fall reduction feature |
| type: boolean |
| |
| st,trim-hs-current: |
| description: | |
| Controls HS driver current trimming for choke compensation |
| - <0> = 18.87 mA target current / nominal + 0% |
| - <1> = 19.165 mA target current / nominal + 1.56% |
| - <2> = 19.46 mA target current / nominal + 3.12% |
| - <3> = 19.755 mA target current / nominal + 4.68% |
| - <4> = 20.05 mA target current / nominal + 6.24% |
| - <5> = 20.345 mA target current / nominal + 7.8% |
| - <6> = 20.64 mA target current / nominal + 9.36% |
| - <7> = 20.935 mA target current / nominal + 10.92% |
| - <8> = 21.23 mA target current / nominal + 12.48% |
| - <9> = 21.525 mA target current / nominal + 14.04% |
| - <10> = 21.82 mA target current / nominal + 15.6% |
| - <11> = 22.115 mA target current / nominal + 17.16% |
| - <12> = 22.458 mA target current / nominal + 19.01% |
| - <13> = 22.755 mA target current / nominal + 20.58% |
| - <14> = 23.052 mA target current / nominal + 22.16% |
| - <15> = 23.348 mA target current / nominal + 23.73% |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0 |
| maximum: 15 |
| default: 0 |
| |
| st,trim-hs-impedance: |
| description: | |
| Controls HS driver impedance tuning for choke compensation |
| - <0> = no impedance offset |
| - <1> = reduce the impedance by 2 ohms |
| - <2> = reduce the impedance by 4 ohms |
| - <3> = reduce the impedance by 6 ohms |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0 |
| maximum: 3 |
| default: 0 |
| |
| st,tune-squelch-level: |
| description: | |
| Tunes the squelch DC threshold value |
| - <0> = no shift in threshold |
| - <1> = threshold shift by +7 mV |
| - <2> = threshold shift by -5 mV |
| - <3> = threshold shift by +14 mV |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0 |
| maximum: 3 |
| default: 0 |
| |
| st,enable-hs-rx-gain-eq: |
| description: Enables the HS Rx gain equalizer |
| type: boolean |
| |
| st,tune-hs-rx-offset: |
| description: | |
| Adjusts the HS Rx offset |
| - <0> = no offset |
| - <1> = offset of +5 mV |
| - <2> = offset of +10 mV |
| - <3> = offset of -5 mV |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| minimum: 0 |
| maximum: 3 |
| default: 0 |
| |
| st,no-hs-ftime-ctrl: |
| description: Disables the HS fall time control of single ended signals during pre-emphasis |
| type: boolean |
| |
| st,no-lsfs-sc: |
| description: Disables the short circuit protection in LS/FS driver |
| type: boolean |
| |
| st,enable-hs-tx-staggering: |
| description: Enables the basic staggering in HS Tx mode |
| type: boolean |
| |
| allOf: |
| - if: |
| properties: |
| reg: |
| const: 0 |
| then: |
| properties: |
| "#phy-cells": |
| const: 0 |
| else: |
| properties: |
| "#phy-cells": |
| const: 1 |
| description: |
| The value is used to select UTMI switch output. |
| 0 for OTG controller and 1 for Host controller. |
| |
| required: |
| - reg |
| - phy-supply |
| - "#phy-cells" |
| |
| additionalProperties: false |
| |
| required: |
| - compatible |
| - reg |
| - clocks |
| - "#address-cells" |
| - "#size-cells" |
| - vdda1v1-supply |
| - vdda1v8-supply |
| - usb-phy@0 |
| - usb-phy@1 |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/clock/stm32mp1-clks.h> |
| #include <dt-bindings/reset/stm32mp1-resets.h> |
| usbphyc: usbphyc@5a006000 { |
| compatible = "st,stm32mp1-usbphyc"; |
| reg = <0x5a006000 0x1000>; |
| clocks = <&rcc USBPHY_K>; |
| resets = <&rcc USBPHY_R>; |
| vdda1v1-supply = <®11>; |
| vdda1v8-supply = <®18>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #clock-cells = <0>; |
| |
| usbphyc_port0: usb-phy@0 { |
| reg = <0>; |
| phy-supply = <&vdd_usb>; |
| #phy-cells = <0>; |
| st,tune-hs-dc-level = <2>; |
| st,enable-fs-rftime-tuning; |
| st,enable-hs-rftime-reduction; |
| st,trim-hs-current = <15>; |
| st,trim-hs-impedance = <1>; |
| st,tune-squelch-level = <3>; |
| st,tune-hs-rx-offset = <2>; |
| st,no-lsfs-sc; |
| connector { |
| compatible = "usb-a-connector"; |
| vbus-supply = <&vbus_sw>; |
| }; |
| }; |
| |
| usbphyc_port1: usb-phy@1 { |
| reg = <1>; |
| phy-supply = <&vdd_usb>; |
| #phy-cells = <1>; |
| st,tune-hs-dc-level = <2>; |
| st,enable-fs-rftime-tuning; |
| st,enable-hs-rftime-reduction; |
| st,trim-hs-current = <15>; |
| st,trim-hs-impedance = <1>; |
| st,tune-squelch-level = <3>; |
| st,tune-hs-rx-offset = <2>; |
| st,no-lsfs-sc; |
| }; |
| }; |
| ... |
