# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Cadence Quad SPI controller

maintainers:
  - Pratyush Yadav <p.yadav@ti.com>

allOf:
  - $ref: spi-controller.yaml#
  - if:
      properties:
        compatible:
          contains:
            const: xlnx,versal-ospi-1.0
    then:
      required:
        - power-domains

properties:
  compatible:
    oneOf:
      - items:
          - enum:
              - ti,k2g-qspi
              - ti,am654-ospi
              - intel,lgm-qspi
              - xlnx,versal-ospi-1.0
          - const: cdns,qspi-nor
      - const: cdns,qspi-nor

  reg:
    items:
      - description: the controller register set
      - description: the controller data area

  interrupts:
    maxItems: 1

  clocks:
    maxItems: 1

  cdns,fifo-depth:
    description:
      Size of the data FIFO in words.
    $ref: "/schemas/types.yaml#/definitions/uint32"
    enum: [ 128, 256 ]
    default: 128

  cdns,fifo-width:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      Bus width of the data FIFO in bytes.
    default: 4

  cdns,trigger-address:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      32-bit indirect AHB trigger address.

  cdns,is-decoded-cs:
    type: boolean
    description:
      Flag to indicate whether decoder is used to select different chip select
      for different memory regions.

  cdns,rclk-en:
    type: boolean
    description:
      Flag to indicate that QSPI return clock is used to latch the read
      data rather than the QSPI clock. Make sure that QSPI return clock
      is populated on the board before using this property.

  power-domains:
    maxItems: 1

  resets:
    maxItems: 2

  reset-names:
    minItems: 1
    maxItems: 2
    items:
      enum: [ qspi, qspi-ocp ]

# subnode's properties
patternProperties:
  "@[0-9a-f]+$":
    type: object
    description:
      Flash device uses the below defined properties in the subnode.

    properties:
      cdns,read-delay:
        $ref: /schemas/types.yaml#/definitions/uint32
        description:
          Delay for read capture logic, in clock cycles.

      cdns,tshsl-ns:
        description:
          Delay in nanoseconds for the length that the master mode chip select
          outputs are de-asserted between transactions.

      cdns,tsd2d-ns:
        description:
          Delay in nanoseconds between one chip select being de-activated
          and the activation of another.

      cdns,tchsh-ns:
        description:
          Delay in nanoseconds between last bit of current transaction and
          deasserting the device chip select (qspi_n_ss_out).

      cdns,tslch-ns:
        description:
          Delay in nanoseconds between setting qspi_n_ss_out low and
          first bit transfer.

required:
  - compatible
  - reg
  - interrupts
  - clocks
  - cdns,fifo-depth
  - cdns,fifo-width
  - cdns,trigger-address
  - '#address-cells'
  - '#size-cells'

unevaluatedProperties: false

examples:
  - |
    qspi: spi@ff705000 {
      compatible = "cdns,qspi-nor";
      #address-cells = <1>;
      #size-cells = <0>;
      reg = <0xff705000 0x1000>,
            <0xffa00000 0x1000>;
      interrupts = <0 151 4>;
      clocks = <&qspi_clk>;
      cdns,fifo-depth = <128>;
      cdns,fifo-width = <4>;
      cdns,trigger-address = <0x00000000>;
      resets = <&rst 0x1>, <&rst 0x2>;
      reset-names = "qspi", "qspi-ocp";

      flash@0 {
              compatible = "jedec,spi-nor";
              reg = <0x0>;
      };
    };