| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* Copyright (C) 2004 Texas Instruments */ |
| |
| /* |
| * This OTG and Embedded Host list is "Targeted Peripheral List". |
| * It should mostly use of USB_DEVICE() or USB_DEVICE_VER() entries.. |
| * |
| * YOU _SHOULD_ CHANGE THIS LIST TO MATCH YOUR PRODUCT AND ITS TESTING! |
| */ |
| |
| static struct usb_device_id productlist_table[] = { |
| |
| /* hubs are optional in OTG, but very handy ... */ |
| { USB_DEVICE_INFO(USB_CLASS_HUB, 0, 0), }, |
| { USB_DEVICE_INFO(USB_CLASS_HUB, 0, 1), }, |
| |
| #ifdef CONFIG_USB_PRINTER /* ignoring nonstatic linkage! */ |
| /* FIXME actually, printers are NOT supposed to use device classes; |
| * they're supposed to use interface classes... |
| */ |
| { USB_DEVICE_INFO(7, 1, 1) }, |
| { USB_DEVICE_INFO(7, 1, 2) }, |
| { USB_DEVICE_INFO(7, 1, 3) }, |
| #endif |
| |
| #ifdef CONFIG_USB_NET_CDCETHER |
| /* Linux-USB CDC Ethernet gadget */ |
| { USB_DEVICE(0x0525, 0xa4a1), }, |
| /* Linux-USB CDC Ethernet + RNDIS gadget */ |
| { USB_DEVICE(0x0525, 0xa4a2), }, |
| #endif |
| |
| #if IS_ENABLED(CONFIG_USB_TEST) |
| /* gadget zero, for testing */ |
| { USB_DEVICE(0x0525, 0xa4a0), }, |
| #endif |
| |
| { } /* Terminating entry */ |
| }; |
| |
| static int is_targeted(struct usb_device *dev) |
| { |
| struct usb_device_id *id = productlist_table; |
| |
| /* HNP test device is _never_ targeted (see OTG spec 6.6.6) */ |
| if ((le16_to_cpu(dev->descriptor.idVendor) == 0x1a0a && |
| le16_to_cpu(dev->descriptor.idProduct) == 0xbadd)) |
| return 0; |
| |
| /* OTG PET device is always targeted (see OTG 2.0 ECN 6.4.2) */ |
| if ((le16_to_cpu(dev->descriptor.idVendor) == 0x1a0a && |
| le16_to_cpu(dev->descriptor.idProduct) == 0x0200)) |
| return 1; |
| |
| /* NOTE: can't use usb_match_id() since interface caches |
| * aren't set up yet. this is cut/paste from that code. |
| */ |
| for (id = productlist_table; id->match_flags; id++) { |
| if ((id->match_flags & USB_DEVICE_ID_MATCH_VENDOR) && |
| id->idVendor != le16_to_cpu(dev->descriptor.idVendor)) |
| continue; |
| |
| if ((id->match_flags & USB_DEVICE_ID_MATCH_PRODUCT) && |
| id->idProduct != le16_to_cpu(dev->descriptor.idProduct)) |
| continue; |
| |
| /* No need to test id->bcdDevice_lo != 0, since 0 is never |
| greater than any unsigned number. */ |
| if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_LO) && |
| (id->bcdDevice_lo > le16_to_cpu(dev->descriptor.bcdDevice))) |
| continue; |
| |
| if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_HI) && |
| (id->bcdDevice_hi < le16_to_cpu(dev->descriptor.bcdDevice))) |
| continue; |
| |
| if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_CLASS) && |
| (id->bDeviceClass != dev->descriptor.bDeviceClass)) |
| continue; |
| |
| if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_SUBCLASS) && |
| (id->bDeviceSubClass != dev->descriptor.bDeviceSubClass)) |
| continue; |
| |
| if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_PROTOCOL) && |
| (id->bDeviceProtocol != dev->descriptor.bDeviceProtocol)) |
| continue; |
| |
| return 1; |
| } |
| |
| /* add other match criteria here ... */ |
| |
| |
| /* OTG MESSAGE: report errors here, customize to match your product */ |
| dev_err(&dev->dev, "device v%04x p%04x is not supported\n", |
| le16_to_cpu(dev->descriptor.idVendor), |
| le16_to_cpu(dev->descriptor.idProduct)); |
| |
| return 0; |
| } |
| |