blob: 15a3bcf32308603597a9ae5d177c2091e20a6dcd [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0-only
#
# Phy drivers for TI platforms
#
config PHY_DA8XX_USB
tristate "TI DA8xx USB PHY Driver"
depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
select GENERIC_PHY
select MFD_SYSCON
help
Enable this to support the USB PHY on DA8xx SoCs.
This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
config PHY_DM816X_USB
tristate "TI dm816x USB PHY driver"
depends on ARCH_OMAP2PLUS || COMPILE_TEST
depends on USB_SUPPORT
select GENERIC_PHY
select USB_PHY
help
Enable this for dm816x USB to work.
config PHY_AM654_SERDES
tristate "TI AM654 SERDES support"
depends on OF && ARCH_K3 || COMPILE_TEST
depends on COMMON_CLK
select GENERIC_PHY
select MULTIPLEXER
select REGMAP_MMIO
select MUX_MMIO
help
This option enables support for TI AM654 SerDes PHY used for
PCIe.
config PHY_J721E_WIZ
tristate "TI J721E WIZ (SERDES Wrapper) support"
depends on OF && ARCH_K3 || COMPILE_TEST
depends on HAS_IOMEM && OF_ADDRESS
depends on COMMON_CLK
select GENERIC_PHY
select MULTIPLEXER
select REGMAP_MMIO
select MUX_MMIO
help
This option enables support for WIZ module present in TI's J721E
SoC. WIZ is a serdes wrapper used to configure some of the input
signals to the SERDES (Sierra/Torrent). This driver configures
three clock selects (pll0, pll1, dig) and resets for each of the
lanes.
config OMAP_CONTROL_PHY
tristate "OMAP CONTROL PHY Driver"
depends on ARCH_OMAP2PLUS || COMPILE_TEST
help
Enable this to add support for the PHY part present in the control
module. This driver has API to power on the USB2 PHY and to write to
the mailbox. The mailbox is present only in omap4 and the register to
power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
additional register to power on USB3 PHY/SATA PHY/PCIE PHY
(PIPE3 PHY).
config OMAP_USB2
tristate "OMAP USB2 PHY Driver"
depends on ARCH_OMAP2PLUS || ARCH_K3
depends on USB_SUPPORT
select GENERIC_PHY
select USB_PHY
select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST
help
Enable this to support the transceiver that is part of SOC. This
driver takes care of all the PHY functionality apart from comparator.
The USB OTG controller communicates with the comparator using this
driver.
config TI_PIPE3
tristate "TI PIPE3 PHY Driver"
depends on ARCH_OMAP2PLUS || COMPILE_TEST
select GENERIC_PHY
select OMAP_CONTROL_PHY
help
Enable this to support the PIPE3 PHY that is part of TI SOCs. This
driver takes care of all the PHY functionality apart from comparator.
This driver interacts with the "OMAP Control PHY Driver" to power
on/off the PHY.
config PHY_TUSB1210
tristate "TI TUSB1210 ULPI PHY module"
depends on USB_ULPI_BUS
select GENERIC_PHY
help
Support for TI TUSB1210 USB ULPI PHY.
config TWL4030_USB
tristate "TWL4030 USB Transceiver Driver"
depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
depends on USB_SUPPORT
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
select GENERIC_PHY
select USB_PHY
help
Enable this to support the USB OTG transceiver on TWL4030
family chips (including the TWL5030 and TPS659x0 devices).
This transceiver supports high and full speed devices plus,
in host mode, low speed.
config PHY_TI_GMII_SEL
tristate
select GENERIC_PHY
select REGMAP
help
This driver supports configuring of the TI CPSW Port mode depending on
the Ethernet PHY connected to the CPSW Port.