mac80211: allow scanning for 5/10 MHz channels in IBSS
Use a chandef instead of just the channel for scanning, and enable
5/10 Mhz scanning for IBSS mode. Also reporting is changed to the new
inform_bss functions.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
diff --git a/net/mac80211/scan.c b/net/mac80211/scan.c
index 819d095..08afe74 100644
--- a/net/mac80211/scan.c
+++ b/net/mac80211/scan.c
@@ -66,6 +66,7 @@
struct cfg80211_bss *cbss;
struct ieee80211_bss *bss;
int clen, srlen;
+ enum nl80211_bss_scan_width scan_width;
s32 signal = 0;
if (local->hw.flags & IEEE80211_HW_SIGNAL_DBM)
@@ -73,8 +74,15 @@
else if (local->hw.flags & IEEE80211_HW_SIGNAL_UNSPEC)
signal = (rx_status->signal * 100) / local->hw.max_signal;
- cbss = cfg80211_inform_bss_frame(local->hw.wiphy, channel,
- mgmt, len, signal, GFP_ATOMIC);
+ scan_width = NL80211_BSS_CHAN_WIDTH_20;
+ if (rx_status->flag & RX_FLAG_5MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_5;
+ if (rx_status->flag & RX_FLAG_10MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_10;
+
+ cbss = cfg80211_inform_bss_width_frame(local->hw.wiphy, channel,
+ scan_width, mgmt, len, signal,
+ GFP_ATOMIC);
if (!cbss)
return NULL;
@@ -300,7 +308,7 @@
rcu_assign_pointer(local->scan_sdata, NULL);
local->scanning = 0;
- local->scan_channel = NULL;
+ local->scan_chandef.chan = NULL;
/* Set power back to normal operating levels. */
ieee80211_hw_config(local, 0);
@@ -635,11 +643,34 @@
{
int skip;
struct ieee80211_channel *chan;
+ enum nl80211_bss_scan_width oper_scan_width;
skip = 0;
chan = local->scan_req->channels[local->scan_channel_idx];
- local->scan_channel = chan;
+ local->scan_chandef.chan = chan;
+ local->scan_chandef.center_freq1 = chan->center_freq;
+ local->scan_chandef.center_freq2 = 0;
+ switch (local->scan_req->scan_width) {
+ case NL80211_BSS_CHAN_WIDTH_5:
+ local->scan_chandef.width = NL80211_CHAN_WIDTH_5;
+ break;
+ case NL80211_BSS_CHAN_WIDTH_10:
+ local->scan_chandef.width = NL80211_CHAN_WIDTH_10;
+ break;
+ case NL80211_BSS_CHAN_WIDTH_20:
+ /* If scanning on oper channel, use whatever channel-type
+ * is currently in use.
+ */
+ oper_scan_width = cfg80211_chandef_to_scan_width(
+ &local->_oper_chandef);
+ if (chan == local->_oper_chandef.chan &&
+ oper_scan_width == local->scan_req->scan_width)
+ local->scan_chandef = local->_oper_chandef;
+ else
+ local->scan_chandef.width = NL80211_CHAN_WIDTH_20_NOHT;
+ break;
+ }
if (ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL))
skip = 1;
@@ -679,7 +710,7 @@
unsigned long *next_delay)
{
/* switch back to the operating channel */
- local->scan_channel = NULL;
+ local->scan_chandef.chan = NULL;
ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);
/* disable PS */
@@ -821,7 +852,8 @@
int ieee80211_request_ibss_scan(struct ieee80211_sub_if_data *sdata,
const u8 *ssid, u8 ssid_len,
- struct ieee80211_channel *chan)
+ struct ieee80211_channel *chan,
+ enum nl80211_bss_scan_width scan_width)
{
struct ieee80211_local *local = sdata->local;
int ret = -EBUSY;
@@ -871,6 +903,7 @@
local->int_scan_req->ssids = &local->scan_ssid;
local->int_scan_req->n_ssids = 1;
+ local->int_scan_req->scan_width = scan_width;
memcpy(local->int_scan_req->ssids[0].ssid, ssid, IEEE80211_MAX_SSID_LEN);
local->int_scan_req->ssids[0].ssid_len = ssid_len;
