altera tse: add support for fixed-links.
Add support for fixed-links in configurations without PHY.
(e.g. connection to a switch, SGMII point to point, SFPs)
Check: Documentation/devicetree/bindings/net/fixed-link.txt.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/altera/altera_tse_main.c b/drivers/net/ethernet/altera/altera_tse_main.c
index 90a7630..0533c05 100644
--- a/drivers/net/ethernet/altera/altera_tse_main.c
+++ b/drivers/net/ethernet/altera/altera_tse_main.c
@@ -777,6 +777,8 @@
struct altera_tse_private *priv = netdev_priv(dev);
struct phy_device *phydev;
struct device_node *phynode;
+ bool fixed_link = false;
+ int rc = 0;
/* Avoid init phy in case of no phy present */
if (!priv->phy_iface)
@@ -789,13 +791,32 @@
phynode = of_parse_phandle(priv->device->of_node, "phy-handle", 0);
if (!phynode) {
- netdev_dbg(dev, "no phy-handle found\n");
- if (!priv->mdio) {
- netdev_err(dev,
- "No phy-handle nor local mdio specified\n");
- return -ENODEV;
+ /* check if a fixed-link is defined in device-tree */
+ if (of_phy_is_fixed_link(priv->device->of_node)) {
+ rc = of_phy_register_fixed_link(priv->device->of_node);
+ if (rc < 0) {
+ netdev_err(dev, "cannot register fixed PHY\n");
+ return rc;
+ }
+
+ /* In the case of a fixed PHY, the DT node associated
+ * to the PHY is the Ethernet MAC DT node.
+ */
+ phynode = of_node_get(priv->device->of_node);
+ fixed_link = true;
+
+ netdev_dbg(dev, "fixed-link detected\n");
+ phydev = of_phy_connect(dev, phynode,
+ &altera_tse_adjust_link,
+ 0, priv->phy_iface);
+ } else {
+ netdev_dbg(dev, "no phy-handle found\n");
+ if (!priv->mdio) {
+ netdev_err(dev, "No phy-handle nor local mdio specified\n");
+ return -ENODEV;
+ }
+ phydev = connect_local_phy(dev);
}
- phydev = connect_local_phy(dev);
} else {
netdev_dbg(dev, "phy-handle found\n");
phydev = of_phy_connect(dev, phynode,
@@ -819,10 +840,10 @@
/* Broken HW is sometimes missing the pull-up resistor on the
* MDIO line, which results in reads to non-existent devices returning
* 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
- * device as well.
+ * device as well. If a fixed-link is used the phy_id is always 0.
* Note: phydev->phy_id is the result of reading the UID PHY registers.
*/
- if (phydev->phy_id == 0) {
+ if ((phydev->phy_id == 0) && !fixed_link) {
netdev_err(dev, "Bad PHY UID 0x%08x\n", phydev->phy_id);
phy_disconnect(phydev);
return -ENODEV;
