sfc: Add support for SFE4003 board and TXC43128 PHY
This board never went into production, but some engineering samples
are in use.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/sfc/falcon_boards.c b/drivers/net/sfc/falcon_boards.c
index bf029b3..cfc6a5b 100644
--- a/drivers/net/sfc/falcon_boards.c
+++ b/drivers/net/sfc/falcon_boards.c
@@ -26,6 +26,7 @@
/* Board types */
#define FALCON_BOARD_SFE4001 0x01
#define FALCON_BOARD_SFE4002 0x02
+#define FALCON_BOARD_SFE4003 0x03
#define FALCON_BOARD_SFN4112F 0x52
/* Board temperature is about 15°C above ambient when air flow is
@@ -582,6 +583,75 @@
return efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
}
+/*****************************************************************************
+ * Support for the SFE4003
+ *
+ */
+static u8 sfe4003_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfe4003_lm87_regs[] = {
+ LM87_IN_LIMITS(0, 0x67, 0x7f), /* 2.5V: 1.5V +/- 10% */
+ LM87_IN_LIMITS(1, 0x4c, 0x5e), /* Vccp1: 1.2V +/- 10% */
+ LM87_IN_LIMITS(2, 0xac, 0xd4), /* 3.3V: 3.3V +/- 10% */
+ LM87_IN_LIMITS(4, 0xac, 0xe0), /* 12V: 10.8-14V */
+ LM87_IN_LIMITS(5, 0x3f, 0x4f), /* Vccp2: 1.0V +/- 10% */
+ LM87_TEMP_INT_LIMITS(0, 70 + FALCON_BOARD_TEMP_BIAS),
+ 0
+};
+
+static struct i2c_board_info sfe4003_hwmon_info = {
+ I2C_BOARD_INFO("lm87", 0x2e),
+ .platform_data = &sfe4003_lm87_channel,
+};
+
+/* Board-specific LED info. */
+#define SFE4003_RED_LED_GPIO 11
+#define SFE4003_LED_ON 1
+#define SFE4003_LED_OFF 0
+
+static void sfe4003_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
+{
+ struct falcon_board *board = falcon_board(efx);
+
+ /* The LEDs were not wired to GPIOs before A3 */
+ if (board->minor < 3 && board->major == 0)
+ return;
+
+ falcon_txc_set_gpio_val(
+ efx, SFE4003_RED_LED_GPIO,
+ (mode == EFX_LED_ON) ? SFE4003_LED_ON : SFE4003_LED_OFF);
+}
+
+static void sfe4003_init_phy(struct efx_nic *efx)
+{
+ struct falcon_board *board = falcon_board(efx);
+
+ /* The LEDs were not wired to GPIOs before A3 */
+ if (board->minor < 3 && board->major == 0)
+ return;
+
+ falcon_txc_set_gpio_dir(efx, SFE4003_RED_LED_GPIO, TXC_GPIO_DIR_OUTPUT);
+ falcon_txc_set_gpio_val(efx, SFE4003_RED_LED_GPIO, SFE4003_LED_OFF);
+}
+
+static int sfe4003_check_hw(struct efx_nic *efx)
+{
+ struct falcon_board *board = falcon_board(efx);
+
+ /* A0/A1/A2 board rev. 4003s report a temperature fault the whole time
+ * (bad sensor) so we mask it out. */
+ unsigned alarm_mask =
+ (board->major == 0 && board->minor <= 2) ?
+ ~LM87_ALARM_TEMP_EXT1 : ~0;
+
+ return efx_check_lm87(efx, alarm_mask);
+}
+
+static int sfe4003_init(struct efx_nic *efx)
+{
+ return efx_init_lm87(efx, &sfe4003_hwmon_info, sfe4003_lm87_regs);
+}
+
static const struct falcon_board_type board_types[] = {
{
.id = FALCON_BOARD_SFE4001,
@@ -604,6 +674,16 @@
.monitor = sfe4002_check_hw,
},
{
+ .id = FALCON_BOARD_SFE4003,
+ .ref_model = "SFE4003",
+ .gen_type = "10GBASE-CX4 adapter",
+ .init = sfe4003_init,
+ .init_phy = sfe4003_init_phy,
+ .fini = efx_fini_lm87,
+ .set_id_led = sfe4003_set_id_led,
+ .monitor = sfe4003_check_hw,
+ },
+ {
.id = FALCON_BOARD_SFN4112F,
.ref_model = "SFN4112F",
.gen_type = "SFP+ adapter",
