Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: drivers/serial/pmac_zilog.c: add missing unlock
  serial: 8250_pnp - add Fujitsu Wacom device
  tty: Fix regressions in the char driver conversion
diff --git a/Documentation/spi/spidev_test.c b/Documentation/spi/spidev_test.c
index 10abd37..16feda9 100644
--- a/Documentation/spi/spidev_test.c
+++ b/Documentation/spi/spidev_test.c
@@ -58,7 +58,7 @@
 	};
 
 	ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
-	if (ret == 1)
+	if (ret < 1)
 		pabort("can't send spi message");
 
 	for (ret = 0; ret < ARRAY_SIZE(tx); ret++) {
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index 568578d..876ca8d 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -46,7 +46,7 @@
 struct omap_musb_board_data {
 	u8	interface_type;
 	u8	mode;
-	u8	power;
+	u16	power;
 };
 
 enum musb_interface    {MUSB_INTERFACE_ULPI, MUSB_INTERFACE_UTMI};
diff --git a/drivers/edac/edac_mce_amd.c b/drivers/edac/edac_mce_amd.c
index f5b6d9f..97e64bc 100644
--- a/drivers/edac/edac_mce_amd.c
+++ b/drivers/edac/edac_mce_amd.c
@@ -294,7 +294,6 @@
 void amd_decode_nb_mce(int node_id, struct err_regs *regs, int handle_errors)
 {
 	u32 ec  = ERROR_CODE(regs->nbsl);
-	u32 xec = EXT_ERROR_CODE(regs->nbsl);
 
 	if (!handle_errors)
 		return;
@@ -324,7 +323,7 @@
 		pr_cont("\n");
 	}
 
-	pr_emerg("%s.\n", EXT_ERR_MSG(xec));
+	pr_emerg("%s.\n", EXT_ERR_MSG(regs->nbsl));
 
 	if (BUS_ERROR(ec) && nb_bus_decoder)
 		nb_bus_decoder(node_id, regs);
@@ -374,7 +373,7 @@
 		 ((m->status & MCI_STATUS_PCC) ? "yes" : "no"));
 
 	/* do the two bits[14:13] together */
-	ecc = m->status & (3ULL << 45);
+	ecc = (m->status >> 45) & 0x3;
 	if (ecc)
 		pr_cont(", %sECC Error", ((ecc == 2) ? "C" : "U"));
 
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 76be229..eb0c3fe 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -416,7 +416,8 @@
 	return 0;
 
 free_sd:
-	sysfs_put(pdesc->value_sd);
+	if (pdesc)
+		sysfs_put(pdesc->value_sd);
 free_id:
 	idr_remove(&pdesc_idr, id);
 	desc->flags &= GPIO_FLAGS_MASK;
diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c
index 18ecae4..b474833 100644
--- a/drivers/of/of_mdio.c
+++ b/drivers/of/of_mdio.c
@@ -69,7 +69,7 @@
 		}
 
 		phy = get_phy_device(mdio, be32_to_cpup(addr));
-		if (!phy) {
+		if (!phy || IS_ERR(phy)) {
 			dev_err(&mdio->dev, "error probing PHY at address %i\n",
 				*addr);
 			continue;
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 3119fdd..a176ab4 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -29,39 +29,6 @@
  * kind, whether express or implied.
  */
 
-/* Platform device Usage :
- *
- * Since PSCs can have multiple function, the correct driver for each one
- * is selected by calling mpc52xx_match_psc_function(...). The function
- * handled by this driver is "uart".
- *
- * The driver init all necessary registers to place the PSC in uart mode without
- * DCD. However, the pin multiplexing aren't changed and should be set either
- * by the bootloader or in the platform init code.
- *
- * The idx field must be equal to the PSC index (e.g. 0 for PSC1, 1 for PSC2,
- * and so on). So the PSC1 is mapped to /dev/ttyPSC0, PSC2 to /dev/ttyPSC1 and
- * so on. But be warned, it's an ABSOLUTE REQUIREMENT ! This is needed mainly
- * fpr the console code : without this 1:1 mapping, at early boot time, when we
- * are parsing the kernel args console=ttyPSC?, we wouldn't know which PSC it
- * will be mapped to.
- */
-
-/* OF Platform device Usage :
- *
- * This driver is only used for PSCs configured in uart mode.  The device
- * tree will have a node for each PSC with "mpc52xx-psc-uart" in the compatible
- * list.
- *
- * By default, PSC devices are enumerated in the order they are found.  However
- * a particular PSC number can be forces by adding 'device_no = <port#>'
- * to the device node.
- *
- * The driver init all necessary registers to place the PSC in uart mode without
- * DCD. However, the pin multiplexing aren't changed and should be set either
- * by the bootloader or in the platform init code.
- */
-
 #undef DEBUG
 
 #include <linux/device.h>
diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index d8356af..e0de0d0 100644
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -204,6 +204,7 @@
 
 	cs->chconf0 = val;
 	mcspi_write_cs_reg(spi, OMAP2_MCSPI_CHCONF0, val);
+	mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHCONF0);
 }
 
 static void omap2_mcspi_set_dma_req(const struct spi_device *spi,
@@ -532,7 +533,7 @@
 					goto out;
 				}
 #ifdef VERBOSE
-				dev_dbg(&spi->dev, "write-%d %04x\n",
+				dev_dbg(&spi->dev, "write-%d %08x\n",
 						word_len, *tx);
 #endif
 				__raw_writel(*tx++, tx_reg);
@@ -550,7 +551,7 @@
 					mcspi_write_chconf0(spi, l);
 				*rx++ = __raw_readl(rx_reg);
 #ifdef VERBOSE
-				dev_dbg(&spi->dev, "read-%d %04x\n",
+				dev_dbg(&spi->dev, "read-%d %08x\n",
 						word_len, *(rx - 1));
 #endif
 			}
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 9ffb0fd..b3a1f92 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -41,7 +41,7 @@
 		spi->master->cleanup(spi);
 
 	spi_master_put(spi->master);
-	kfree(dev);
+	kfree(spi);
 }
 
 static ssize_t
@@ -257,6 +257,7 @@
 {
 	static DEFINE_MUTEX(spi_add_lock);
 	struct device *dev = spi->master->dev.parent;
+	struct device *d;
 	int status;
 
 	/* Chipselects are numbered 0..max; validate. */
@@ -278,10 +279,11 @@
 	 */
 	mutex_lock(&spi_add_lock);
 
-	if (bus_find_device_by_name(&spi_bus_type, NULL, dev_name(&spi->dev))
-			!= NULL) {
+	d = bus_find_device_by_name(&spi_bus_type, NULL, dev_name(&spi->dev));
+	if (d != NULL) {
 		dev_err(dev, "chipselect %d already in use\n",
 				spi->chip_select);
+		put_device(d);
 		status = -EBUSY;
 		goto done;
 	}
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index be6331e..5e1a253 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -1542,6 +1542,9 @@
 	{ USB_DEVICE(0x1bbb, 0x0003), /* Alcatel OT-I650 */
 	.driver_info = NO_UNION_NORMAL, /* reports zero length descriptor */
 	},
+	{ USB_DEVICE(0x1576, 0x03b1), /* Maretron USB100 */
+	.driver_info = NO_UNION_NORMAL, /* reports zero length descriptor */
+	},
 
 	/* Nokia S60 phones expose two ACM channels. The first is
 	 * a modem and is picked up by the standard AT-command
diff --git a/drivers/usb/core/Kconfig b/drivers/usb/core/Kconfig
index 97a819c..7e594449 100644
--- a/drivers/usb/core/Kconfig
+++ b/drivers/usb/core/Kconfig
@@ -109,7 +109,7 @@
 config USB_OTG
 	bool
 	depends on USB && EXPERIMENTAL
-	select USB_SUSPEND
+	depends on USB_SUSPEND
 	default n
 
 
diff --git a/drivers/usb/core/generic.c b/drivers/usb/core/generic.c
index bdf87a8..2c95153 100644
--- a/drivers/usb/core/generic.c
+++ b/drivers/usb/core/generic.c
@@ -120,7 +120,7 @@
 		 * than a vendor-specific driver. */
 		else if (udev->descriptor.bDeviceClass !=
 						USB_CLASS_VENDOR_SPEC &&
-				(!desc || desc->bInterfaceClass !=
+				(desc && desc->bInterfaceClass !=
 						USB_CLASS_VENDOR_SPEC)) {
 			best = c;
 			break;
diff --git a/drivers/usb/core/inode.c b/drivers/usb/core/inode.c
index 97b40ce..4a6366a 100644
--- a/drivers/usb/core/inode.c
+++ b/drivers/usb/core/inode.c
@@ -515,13 +515,13 @@
 	*dentry = NULL;
 	mutex_lock(&parent->d_inode->i_mutex);
 	*dentry = lookup_one_len(name, parent, strlen(name));
-	if (!IS_ERR(dentry)) {
+	if (!IS_ERR(*dentry)) {
 		if ((mode & S_IFMT) == S_IFDIR)
 			error = usbfs_mkdir (parent->d_inode, *dentry, mode);
 		else 
 			error = usbfs_create (parent->d_inode, *dentry, mode);
 	} else
-		error = PTR_ERR(dentry);
+		error = PTR_ERR(*dentry);
 	mutex_unlock(&parent->d_inode->i_mutex);
 
 	return error;
diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c
index 1297e9b..0561430 100644
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -718,7 +718,7 @@
 EXPORT_SYMBOL_GPL(__usb_get_extra_descriptor);
 
 /**
- * usb_buffer_alloc - allocate dma-consistent buffer for URB_NO_xxx_DMA_MAP
+ * usb_alloc_coherent - allocate dma-consistent buffer for URB_NO_xxx_DMA_MAP
  * @dev: device the buffer will be used with
  * @size: requested buffer size
  * @mem_flags: affect whether allocation may block
@@ -737,30 +737,30 @@
  * architectures where CPU caches are not DMA-coherent.  On systems without
  * bus-snooping caches, these buffers are uncached.
  *
- * When the buffer is no longer used, free it with usb_buffer_free().
+ * When the buffer is no longer used, free it with usb_free_coherent().
  */
-void *usb_buffer_alloc(struct usb_device *dev, size_t size, gfp_t mem_flags,
-		       dma_addr_t *dma)
+void *usb_alloc_coherent(struct usb_device *dev, size_t size, gfp_t mem_flags,
+			 dma_addr_t *dma)
 {
 	if (!dev || !dev->bus)
 		return NULL;
 	return hcd_buffer_alloc(dev->bus, size, mem_flags, dma);
 }
-EXPORT_SYMBOL_GPL(usb_buffer_alloc);
+EXPORT_SYMBOL_GPL(usb_alloc_coherent);
 
 /**
- * usb_buffer_free - free memory allocated with usb_buffer_alloc()
+ * usb_free_coherent - free memory allocated with usb_alloc_coherent()
  * @dev: device the buffer was used with
  * @size: requested buffer size
  * @addr: CPU address of buffer
  * @dma: DMA address of buffer
  *
  * This reclaims an I/O buffer, letting it be reused.  The memory must have
- * been allocated using usb_buffer_alloc(), and the parameters must match
+ * been allocated using usb_alloc_coherent(), and the parameters must match
  * those provided in that allocation request.
  */
-void usb_buffer_free(struct usb_device *dev, size_t size, void *addr,
-		     dma_addr_t dma)
+void usb_free_coherent(struct usb_device *dev, size_t size, void *addr,
+		       dma_addr_t dma)
 {
 	if (!dev || !dev->bus)
 		return;
@@ -768,7 +768,7 @@
 		return;
 	hcd_buffer_free(dev->bus, size, addr, dma);
 }
-EXPORT_SYMBOL_GPL(usb_buffer_free);
+EXPORT_SYMBOL_GPL(usb_free_coherent);
 
 /**
  * usb_buffer_map - create DMA mapping(s) for an urb
diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 124a8cc..1f73b48 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -2145,6 +2145,7 @@
 	u32 epctrl;
 	u32 mps;
 	int dir_in;
+	int ret = 0;
 
 	dev_dbg(hsotg->dev,
 		"%s: ep %s: a 0x%02x, attr 0x%02x, mps 0x%04x, intr %d\n",
@@ -2196,7 +2197,8 @@
 	switch (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
 	case USB_ENDPOINT_XFER_ISOC:
 		dev_err(hsotg->dev, "no current ISOC support\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto out;
 
 	case USB_ENDPOINT_XFER_BULK:
 		epctrl |= S3C_DxEPCTL_EPType_Bulk;
@@ -2235,8 +2237,9 @@
 	/* enable the endpoint interrupt */
 	s3c_hsotg_ctrl_epint(hsotg, index, dir_in, 1);
 
+out:
 	spin_unlock_irqrestore(&hs_ep->lock, flags);
-	return 0;
+	return ret;
 }
 
 static int s3c_hsotg_ep_disable(struct usb_ep *ep)
diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c
index 68b83ab..944291e 100644
--- a/drivers/usb/host/ohci-at91.c
+++ b/drivers/usb/host/ohci-at91.c
@@ -331,6 +331,8 @@
 	 */
 	if (at91_suspend_entering_slow_clock()) {
 		ohci_usb_reset (ohci);
+		/* flush the writes */
+		(void) ohci_readl (ohci, &ohci->regs->control);
 		at91_stop_clock();
 	}
 
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index 32bbce9..65cac8c 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -697,7 +697,7 @@
 	u16		wLength
 ) {
 	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
-	int		ports = hcd_to_bus (hcd)->root_hub->maxchild;
+	int		ports = ohci->num_ports;
 	u32		temp;
 	int		retval = 0;
 
diff --git a/drivers/usb/host/oxu210hp-hcd.c b/drivers/usb/host/oxu210hp-hcd.c
index 50f57f4..e62b30b 100644
--- a/drivers/usb/host/oxu210hp-hcd.c
+++ b/drivers/usb/host/oxu210hp-hcd.c
@@ -660,13 +660,13 @@
 		if (qh->dummy == NULL) {
 			oxu_dbg(oxu, "no dummy td\n");
 			oxu->qh_used[i] = 0;
-
-			return NULL;
+			qh = NULL;
+			goto unlock;
 		}
 
 		oxu->qh_used[i] = 1;
 	}
-
+unlock:
 	spin_unlock(&oxu->mem_lock);
 
 	return qh;
diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c
index e11cc3a..3b867a8 100644
--- a/drivers/usb/host/sl811-hcd.c
+++ b/drivers/usb/host/sl811-hcd.c
@@ -720,10 +720,10 @@
 		/* port status seems weird until after reset, so
 		 * force the reset and make khubd clean up later.
 		 */
-		if (sl811->stat_insrmv & 1)
-			sl811->port1 |= 1 << USB_PORT_FEAT_CONNECTION;
-		else
+		if (irqstat & SL11H_INTMASK_RD)
 			sl811->port1 &= ~(1 << USB_PORT_FEAT_CONNECTION);
+		else
+			sl811->port1 |= 1 << USB_PORT_FEAT_CONNECTION;
 
 		sl811->port1 |= 1 << USB_PORT_FEAT_C_CONNECTION;
 
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index c09539b..d64f572 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -582,6 +582,19 @@
 	return EP_INTERVAL(interval);
 }
 
+/* The "Mult" field in the endpoint context is only set for SuperSpeed devices.
+ * High speed endpoint descriptors can define "the number of additional
+ * transaction opportunities per microframe", but that goes in the Max Burst
+ * endpoint context field.
+ */
+static inline u32 xhci_get_endpoint_mult(struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	if (udev->speed != USB_SPEED_SUPER || !ep->ss_ep_comp)
+		return 0;
+	return ep->ss_ep_comp->desc.bmAttributes;
+}
+
 static inline u32 xhci_get_endpoint_type(struct usb_device *udev,
 		struct usb_host_endpoint *ep)
 {
@@ -612,6 +625,36 @@
 	return type;
 }
 
+/* Return the maximum endpoint service interval time (ESIT) payload.
+ * Basically, this is the maxpacket size, multiplied by the burst size
+ * and mult size.
+ */
+static inline u32 xhci_get_max_esit_payload(struct xhci_hcd *xhci,
+		struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	int max_burst;
+	int max_packet;
+
+	/* Only applies for interrupt or isochronous endpoints */
+	if (usb_endpoint_xfer_control(&ep->desc) ||
+			usb_endpoint_xfer_bulk(&ep->desc))
+		return 0;
+
+	if (udev->speed == USB_SPEED_SUPER) {
+		if (ep->ss_ep_comp)
+			return ep->ss_ep_comp->desc.wBytesPerInterval;
+		xhci_warn(xhci, "WARN no SS endpoint companion descriptor.\n");
+		/* Assume no bursts, no multiple opportunities to send. */
+		return ep->desc.wMaxPacketSize;
+	}
+
+	max_packet = ep->desc.wMaxPacketSize & 0x3ff;
+	max_burst = (ep->desc.wMaxPacketSize & 0x1800) >> 11;
+	/* A 0 in max burst means 1 transfer per ESIT */
+	return max_packet * (max_burst + 1);
+}
+
 int xhci_endpoint_init(struct xhci_hcd *xhci,
 		struct xhci_virt_device *virt_dev,
 		struct usb_device *udev,
@@ -623,6 +666,7 @@
 	struct xhci_ring *ep_ring;
 	unsigned int max_packet;
 	unsigned int max_burst;
+	u32 max_esit_payload;
 
 	ep_index = xhci_get_endpoint_index(&ep->desc);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
@@ -644,6 +688,7 @@
 	ep_ctx->deq = ep_ring->first_seg->dma | ep_ring->cycle_state;
 
 	ep_ctx->ep_info = xhci_get_endpoint_interval(udev, ep);
+	ep_ctx->ep_info |= EP_MULT(xhci_get_endpoint_mult(udev, ep));
 
 	/* FIXME dig Mult and streams info out of ep companion desc */
 
@@ -689,6 +734,26 @@
 	default:
 		BUG();
 	}
+	max_esit_payload = xhci_get_max_esit_payload(xhci, udev, ep);
+	ep_ctx->tx_info = MAX_ESIT_PAYLOAD_FOR_EP(max_esit_payload);
+
+	/*
+	 * XXX no idea how to calculate the average TRB buffer length for bulk
+	 * endpoints, as the driver gives us no clue how big each scatter gather
+	 * list entry (or buffer) is going to be.
+	 *
+	 * For isochronous and interrupt endpoints, we set it to the max
+	 * available, until we have new API in the USB core to allow drivers to
+	 * declare how much bandwidth they actually need.
+	 *
+	 * Normally, it would be calculated by taking the total of the buffer
+	 * lengths in the TD and then dividing by the number of TRBs in a TD,
+	 * including link TRBs, No-op TRBs, and Event data TRBs.  Since we don't
+	 * use Event Data TRBs, and we don't chain in a link TRB on short
+	 * transfers, we're basically dividing by 1.
+	 */
+	ep_ctx->tx_info |= AVG_TRB_LENGTH_FOR_EP(max_esit_payload);
+
 	/* FIXME Debug endpoint context */
 	return 0;
 }
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index e5eb09b..ea389e9 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -609,6 +609,10 @@
 #define MAX_PACKET_MASK		(0xffff << 16)
 #define MAX_PACKET_DECODED(p)	(((p) >> 16) & 0xffff)
 
+/* tx_info bitmasks */
+#define AVG_TRB_LENGTH_FOR_EP(p)	((p) & 0xffff)
+#define MAX_ESIT_PAYLOAD_FOR_EP(p)	(((p) & 0xffff) << 16)
+
 
 /**
  * struct xhci_input_control_context
diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
index b4c783c..07fe490 100644
--- a/drivers/usb/musb/Kconfig
+++ b/drivers/usb/musb/Kconfig
@@ -42,7 +42,7 @@
 	default y if (BF52x && !BF522 && !BF523)
 
 comment "DaVinci 35x and 644x USB support"
-	depends on USB_MUSB_HDRC && ARCH_DAVINCI
+	depends on USB_MUSB_HDRC && ARCH_DAVINCI_DMx
 
 comment "OMAP 243x high speed USB support"
 	depends on USB_MUSB_HDRC && ARCH_OMAP2430
diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile
index 85710cc..3a485da 100644
--- a/drivers/usb/musb/Makefile
+++ b/drivers/usb/musb/Makefile
@@ -6,7 +6,7 @@
 
 obj-$(CONFIG_USB_MUSB_HDRC)	+= musb_hdrc.o
 
-ifeq ($(CONFIG_ARCH_DAVINCI),y)
+ifeq ($(CONFIG_ARCH_DAVINCI_DMx),y)
 	musb_hdrc-objs	+= davinci.o
 endif
 
diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c
index 719a22d..ec8d324 100644
--- a/drivers/usb/musb/blackfin.c
+++ b/drivers/usb/musb/blackfin.c
@@ -172,13 +172,7 @@
 
 	spin_unlock_irqrestore(&musb->lock, flags);
 
-	/* REVISIT we sometimes get spurious IRQs on g_ep0
-	 * not clear why... fall in BF54x too.
-	 */
-	if (retval != IRQ_HANDLED)
-		DBG(5, "spurious?\n");
-
-	return IRQ_HANDLED;
+	return retval;
 }
 
 static void musb_conn_timer_handler(unsigned long _musb)
diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c
index 29bce5c0..ce2e16f 100644
--- a/drivers/usb/musb/davinci.c
+++ b/drivers/usb/musb/davinci.c
@@ -444,6 +444,8 @@
 	return 0;
 
 fail:
+	clk_disable(musb->clock);
+
 	usb_nop_xceiv_unregister();
 	return -ENODEV;
 }
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 0e8b8ab..705cc4a 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -965,10 +965,8 @@
 	spin_lock_irqsave(&musb->lock, flags);
 	musb_platform_disable(musb);
 	musb_generic_disable(musb);
-	if (musb->clock) {
+	if (musb->clock)
 		clk_put(musb->clock);
-		musb->clock = NULL;
-	}
 	spin_unlock_irqrestore(&musb->lock, flags);
 
 	/* FIXME power down */
@@ -1853,15 +1851,6 @@
 	put_device(musb->xceiv->dev);
 #endif
 
-	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
-	musb_platform_exit(musb);
-	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
-
-	if (musb->clock) {
-		clk_disable(musb->clock);
-		clk_put(musb->clock);
-	}
-
 #ifdef CONFIG_USB_MUSB_HDRC_HCD
 	usb_put_hcd(musb_to_hcd(musb));
 #else
@@ -1889,8 +1878,10 @@
 	 */
 	if (!plat) {
 		dev_dbg(dev, "no platform_data?\n");
-		return -ENODEV;
+		status = -ENODEV;
+		goto fail0;
 	}
+
 	switch (plat->mode) {
 	case MUSB_HOST:
 #ifdef CONFIG_USB_MUSB_HDRC_HCD
@@ -1912,13 +1903,16 @@
 #endif
 	default:
 		dev_err(dev, "incompatible Kconfig role setting\n");
-		return -EINVAL;
+		status = -EINVAL;
+		goto fail0;
 	}
 
 	/* allocate */
 	musb = allocate_instance(dev, plat->config, ctrl);
-	if (!musb)
-		return -ENOMEM;
+	if (!musb) {
+		status = -ENOMEM;
+		goto fail0;
+	}
 
 	spin_lock_init(&musb->lock);
 	musb->board_mode = plat->mode;
@@ -1936,7 +1930,7 @@
 		if (IS_ERR(musb->clock)) {
 			status = PTR_ERR(musb->clock);
 			musb->clock = NULL;
-			goto fail;
+			goto fail1;
 		}
 	}
 
@@ -1955,12 +1949,12 @@
 	 */
 	musb->isr = generic_interrupt;
 	status = musb_platform_init(musb);
-
 	if (status < 0)
-		goto fail;
+		goto fail2;
+
 	if (!musb->isr) {
 		status = -ENODEV;
-		goto fail2;
+		goto fail3;
 	}
 
 #ifndef CONFIG_MUSB_PIO_ONLY
@@ -1986,7 +1980,7 @@
 			? MUSB_CONTROLLER_MHDRC
 			: MUSB_CONTROLLER_HDRC, musb);
 	if (status < 0)
-		goto fail2;
+		goto fail3;
 
 #ifdef CONFIG_USB_MUSB_OTG
 	setup_timer(&musb->otg_timer, musb_otg_timer_func, (unsigned long) musb);
@@ -1999,7 +1993,7 @@
 	if (request_irq(nIrq, musb->isr, 0, dev_name(dev), musb)) {
 		dev_err(dev, "request_irq %d failed!\n", nIrq);
 		status = -ENODEV;
-		goto fail2;
+		goto fail3;
 	}
 	musb->nIrq = nIrq;
 /* FIXME this handles wakeup irqs wrong */
@@ -2039,8 +2033,6 @@
 		musb->xceiv->state = OTG_STATE_A_IDLE;
 
 		status = usb_add_hcd(musb_to_hcd(musb), -1, 0);
-		if (status)
-			goto fail;
 
 		DBG(1, "%s mode, status %d, devctl %02x %c\n",
 			"HOST", status,
@@ -2055,8 +2047,6 @@
 		musb->xceiv->state = OTG_STATE_B_IDLE;
 
 		status = musb_gadget_setup(musb);
-		if (status)
-			goto fail;
 
 		DBG(1, "%s mode, status %d, dev%02x\n",
 			is_otg_enabled(musb) ? "OTG" : "PERIPHERAL",
@@ -2064,12 +2054,14 @@
 			musb_readb(musb->mregs, MUSB_DEVCTL));
 
 	}
+	if (status < 0)
+		goto fail3;
 
 #ifdef CONFIG_SYSFS
 	status = sysfs_create_group(&musb->controller->kobj, &musb_attr_group);
-#endif
 	if (status)
-		goto fail2;
+		goto fail4;
+#endif
 
 	dev_info(dev, "USB %s mode controller at %p using %s, IRQ %d\n",
 			({char *s;
@@ -2085,17 +2077,29 @@
 
 	return 0;
 
-fail2:
+fail4:
+	if (!is_otg_enabled(musb) && is_host_enabled(musb))
+		usb_remove_hcd(musb_to_hcd(musb));
+	else
+		musb_gadget_cleanup(musb);
+
+fail3:
+	if (musb->irq_wake)
+		device_init_wakeup(dev, 0);
 	musb_platform_exit(musb);
-fail:
+
+fail2:
+	if (musb->clock)
+		clk_put(musb->clock);
+
+fail1:
 	dev_err(musb->controller,
 		"musb_init_controller failed with status %d\n", status);
 
-	if (musb->clock)
-		clk_put(musb->clock);
-	device_init_wakeup(dev, 0);
 	musb_free(musb);
 
+fail0:
+
 	return status;
 
 }
@@ -2132,7 +2136,6 @@
 	/* clobbered by use_dma=n */
 	orig_dma_mask = dev->dma_mask;
 #endif
-
 	status = musb_init_controller(dev, irq, base);
 	if (status < 0)
 		iounmap(base);
@@ -2155,6 +2158,10 @@
 	if (musb->board_mode == MUSB_HOST)
 		usb_remove_hcd(musb_to_hcd(musb));
 #endif
+	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
+	musb_platform_exit(musb);
+	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
+
 	musb_free(musb);
 	iounmap(ctrl_base);
 	device_init_wakeup(&pdev->dev, 0);
@@ -2176,6 +2183,7 @@
 	if (is_host_enabled(musb)) {
 		musb_context.frame = musb_readw(musb_base, MUSB_FRAME);
 		musb_context.testmode = musb_readb(musb_base, MUSB_TESTMODE);
+		musb_context.busctl = musb_read_ulpi_buscontrol(musb->mregs);
 	}
 	musb_context.power = musb_readb(musb_base, MUSB_POWER);
 	musb_context.intrtxe = musb_readw(musb_base, MUSB_INTRTXE);
@@ -2247,6 +2255,7 @@
 	if (is_host_enabled(musb)) {
 		musb_writew(musb_base, MUSB_FRAME, musb_context.frame);
 		musb_writeb(musb_base, MUSB_TESTMODE, musb_context.testmode);
+		musb_write_ulpi_buscontrol(musb->mregs, musb_context.busctl);
 	}
 	musb_writeb(musb_base, MUSB_POWER, musb_context.power);
 	musb_writew(musb_base, MUSB_INTRTXE, musb_context.intrtxe);
diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h
index cd9f4a9..ac17b00 100644
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -478,7 +478,7 @@
 	u16 frame;
 	u8 index, testmode;
 
-	u8 devctl, misc;
+	u8 devctl, busctl, misc;
 
 	struct musb_csr_regs index_regs[MUSB_C_NUM_EPS];
 };
diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c
index dec896e..877d20b 100644
--- a/drivers/usb/musb/musb_host.c
+++ b/drivers/usb/musb/musb_host.c
@@ -2042,6 +2042,7 @@
 		 * odd, rare, error prone, but legal.
 		 */
 		kfree(qh);
+		qh = NULL;
 		ret = 0;
 	} else
 		ret = musb_schedule(musb, qh,
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index 490cdf1..8259263 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -331,8 +331,5 @@
 
 	musb_platform_suspend(musb);
 
-	clk_put(musb->clock);
-	musb->clock = NULL;
-
 	return 0;
 }
diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c
index ab776a8..60d3938 100644
--- a/drivers/usb/musb/tusb6010.c
+++ b/drivers/usb/musb/tusb6010.c
@@ -29,6 +29,19 @@
 #define TUSB_REV_MAJOR(reg_val)		((reg_val >> 4) & 0xf)
 #define TUSB_REV_MINOR(reg_val)		(reg_val & 0xf)
 
+#ifdef CONFIG_PM
+/* REVISIT: These should be only needed if somebody implements off idle */
+void musb_platform_save_context(struct musb *musb,
+			struct musb_context_registers *musb_context)
+{
+}
+
+void musb_platform_restore_context(struct musb *musb,
+			struct musb_context_registers *musb_context)
+{
+}
+#endif
+
 /*
  * Checks the revision. We need to use the DMA register as 3.0 does not
  * have correct versions for TUSB_PRCM_REV or TUSB_INT_CTRL_REV.
diff --git a/drivers/usb/musb/tusb6010_omap.c b/drivers/usb/musb/tusb6010_omap.c
index 5afa070..c061a88 100644
--- a/drivers/usb/musb/tusb6010_omap.c
+++ b/drivers/usb/musb/tusb6010_omap.c
@@ -39,7 +39,7 @@
 
 	struct tusb_omap_dma	*tusb_dma;
 
-	void __iomem		*dma_addr;
+	dma_addr_t		dma_addr;
 
 	u32			len;
 	u16			packet_sz;
@@ -126,6 +126,7 @@
 	struct tusb_omap_dma_ch	*chdat = to_chdat(channel);
 	struct tusb_omap_dma	*tusb_dma = chdat->tusb_dma;
 	struct musb		*musb = chdat->musb;
+	struct device		*dev = musb->controller;
 	struct musb_hw_ep	*hw_ep = chdat->hw_ep;
 	void __iomem		*ep_conf = hw_ep->conf;
 	void __iomem		*mbase = musb->mregs;
@@ -173,13 +174,15 @@
 		DBG(3, "Using PIO for remaining %lu bytes\n", pio);
 		buf = phys_to_virt((u32)chdat->dma_addr) + chdat->transfer_len;
 		if (chdat->tx) {
-			dma_cache_maint(phys_to_virt((u32)chdat->dma_addr),
-					chdat->transfer_len, DMA_TO_DEVICE);
+			dma_unmap_single(dev, chdat->dma_addr,
+						chdat->transfer_len,
+						DMA_TO_DEVICE);
 			musb_write_fifo(hw_ep, pio, buf);
 		} else {
+			dma_unmap_single(dev, chdat->dma_addr,
+						chdat->transfer_len,
+						DMA_FROM_DEVICE);
 			musb_read_fifo(hw_ep, pio, buf);
-			dma_cache_maint(phys_to_virt((u32)chdat->dma_addr),
-					chdat->transfer_len, DMA_FROM_DEVICE);
 		}
 		channel->actual_len += pio;
 	}
@@ -224,6 +227,7 @@
 	struct tusb_omap_dma_ch		*chdat = to_chdat(channel);
 	struct tusb_omap_dma		*tusb_dma = chdat->tusb_dma;
 	struct musb			*musb = chdat->musb;
+	struct device			*dev = musb->controller;
 	struct musb_hw_ep		*hw_ep = chdat->hw_ep;
 	void __iomem			*mbase = musb->mregs;
 	void __iomem			*ep_conf = hw_ep->conf;
@@ -299,14 +303,16 @@
 	chdat->packet_sz = packet_sz;
 	chdat->len = len;
 	channel->actual_len = 0;
-	chdat->dma_addr = (void __iomem *)dma_addr;
+	chdat->dma_addr = dma_addr;
 	channel->status = MUSB_DMA_STATUS_BUSY;
 
 	/* Since we're recycling dma areas, we need to clean or invalidate */
 	if (chdat->tx)
-		dma_cache_maint(phys_to_virt(dma_addr), len, DMA_TO_DEVICE);
+		dma_map_single(dev, phys_to_virt(dma_addr), len,
+				DMA_TO_DEVICE);
 	else
-		dma_cache_maint(phys_to_virt(dma_addr), len, DMA_FROM_DEVICE);
+		dma_map_single(dev, phys_to_virt(dma_addr), len,
+				DMA_FROM_DEVICE);
 
 	/* Use 16-bit transfer if dma_addr is not 32-bit aligned */
 	if ((dma_addr & 0x3) == 0) {
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index ca9d866..84d0eda 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -305,6 +305,11 @@
 #define ZTE_PRODUCT_CDMA_TECH			0xfffe
 #define ZTE_PRODUCT_AC8710			0xfff1
 #define ZTE_PRODUCT_AC2726			0xfff5
+#define ZTE_PRODUCT_AC8710T			0xffff
+
+/* ZTE PRODUCTS -- alternate vendor ID */
+#define ZTE_VENDOR_ID2				0x1d6b
+#define ZTE_PRODUCT_MF_330			0x0002
 
 #define BENQ_VENDOR_ID				0x04a5
 #define BENQ_PRODUCT_H10			0x4068
@@ -373,6 +378,8 @@
 #define HAIER_VENDOR_ID				0x201e
 #define HAIER_PRODUCT_CE100			0x2009
 
+#define CINTERION_VENDOR_ID			0x0681
+
 /* some devices interfaces need special handling due to a number of reasons */
 enum option_blacklist_reason {
 		OPTION_BLACKLIST_NONE = 0,
@@ -679,6 +686,8 @@
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710T, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE(ZTE_VENDOR_ID2, ZTE_PRODUCT_MF_330) },
 	{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) },
 	{ USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) },
 	{ USB_DEVICE(ALINK_VENDOR_ID, DLINK_PRODUCT_DWM_652_U5) }, /* Yes, ALINK_VENDOR_ID */
@@ -716,6 +725,7 @@
 	{ USB_DEVICE(PIRELLI_VENDOR_ID, PIRELLI_PRODUCT_1011)},
 	{ USB_DEVICE(PIRELLI_VENDOR_ID, PIRELLI_PRODUCT_1012)},
 
+	{ USB_DEVICE(CINTERION_VENDOR_ID, 0x0047) },
 	{ } /* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, option_ids);
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index c97a0bb..c28b160 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -59,6 +59,7 @@
 	{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_ALDIGA) },
 	{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_MMX) },
 	{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_GPRS) },
+	{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_HCR331) },
 	{ USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID) },
 	{ USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID_RSAQ5) },
 	{ USB_DEVICE(ATEN_VENDOR_ID, ATEN_PRODUCT_ID) },
diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h
index a352d5f3..23c09b3 100644
--- a/drivers/usb/serial/pl2303.h
+++ b/drivers/usb/serial/pl2303.h
@@ -20,6 +20,7 @@
 #define PL2303_PRODUCT_ID_ALDIGA	0x0611
 #define PL2303_PRODUCT_ID_MMX		0x0612
 #define PL2303_PRODUCT_ID_GPRS		0x0609
+#define PL2303_PRODUCT_ID_HCR331	0x331a
 
 #define ATEN_VENDOR_ID		0x0557
 #define ATEN_VENDOR_ID2		0x0547
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index 880e990..e1bfda3 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -1735,7 +1735,7 @@
 		return -ENOENT;
 	}
 	if (fw_p->size > TI_FIRMWARE_BUF_SIZE) {
-		dev_err(&dev->dev, "%s - firmware too large %d \n", __func__, fw_p->size);
+		dev_err(&dev->dev, "%s - firmware too large %zu\n", __func__, fw_p->size);
 		return -ENOENT;
 	}
 
diff --git a/fs/notify/inotify/Kconfig b/fs/notify/inotify/Kconfig
index 3e56dbf..b3a159b 100644
--- a/fs/notify/inotify/Kconfig
+++ b/fs/notify/inotify/Kconfig
@@ -15,6 +15,7 @@
 
 config INOTIFY_USER
 	bool "Inotify support for userspace"
+	select ANON_INODES
 	select FSNOTIFY
 	default y
 	---help---
diff --git a/include/linux/usb.h b/include/linux/usb.h
index ce1323c..739f1fd 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -1085,7 +1085,7 @@
  * Alternatively, drivers may pass the URB_NO_xxx_DMA_MAP transfer flags,
  * which tell the host controller driver that no such mapping is needed since
  * the device driver is DMA-aware.  For example, a device driver might
- * allocate a DMA buffer with usb_buffer_alloc() or call usb_buffer_map().
+ * allocate a DMA buffer with usb_alloc_coherent() or call usb_buffer_map().
  * When these transfer flags are provided, host controller drivers will
  * attempt to use the dma addresses found in the transfer_dma and/or
  * setup_dma fields rather than determining a dma address themselves.
@@ -1366,11 +1366,23 @@
 	return (urb->transfer_flags & URB_DIR_MASK) == URB_DIR_OUT;
 }
 
-void *usb_buffer_alloc(struct usb_device *dev, size_t size,
+void *usb_alloc_coherent(struct usb_device *dev, size_t size,
 	gfp_t mem_flags, dma_addr_t *dma);
-void usb_buffer_free(struct usb_device *dev, size_t size,
+void usb_free_coherent(struct usb_device *dev, size_t size,
 	void *addr, dma_addr_t dma);
 
+/* Compatible macros while we switch over */
+static inline void *usb_buffer_alloc(struct usb_device *dev, size_t size,
+				     gfp_t mem_flags, dma_addr_t *dma)
+{
+	return usb_alloc_coherent(dev, size, mem_flags, dma);
+}
+static inline void usb_buffer_free(struct usb_device *dev, size_t size,
+				   void *addr, dma_addr_t dma)
+{
+	return usb_free_coherent(dev, size, addr, dma);
+}
+
 #if 0
 struct urb *usb_buffer_map(struct urb *urb);
 void usb_buffer_dmasync(struct urb *urb);