Merge branches 'ib-mfd-clk-gpio-power-regulator-rtc-5.3', 'ib-mfd-clk-regulator-rtc-5.3', 'ib-mfd-cros-5.3' and 'ib-mfd-regulator-5.3' into ibs-for-mfd-merged
diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt
index a48df7c..41671e0 100644
--- a/Documentation/devicetree/bindings/mfd/lp87565.txt
+++ b/Documentation/devicetree/bindings/mfd/lp87565.txt
@@ -41,3 +41,39 @@
};
};
};
+
+TI LP87561 PMIC:
+
+This is a single output 4-phase regulator configuration
+
+Required properties:
+ - compatible: "ti,lp87561-q1"
+ - reg: I2C slave address.
+ - gpio-controller: Marks the device node as a GPIO Controller.
+ - #gpio-cells: Should be two. The first cell is the pin number and
+ the second cell is used to specify flags.
+ See ../gpio/gpio.txt for more information.
+ - xxx-in-supply: Phandle to parent supply node of each regulator
+ populated under regulators node. xxx should match
+ the supply_name populated in driver.
+Example:
+
+lp87561_pmic: pmic@62 {
+ compatible = "ti,lp87561-q1";
+ reg = <0x62>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck3210-in-supply = <&vsys_3v3>;
+
+ regulators: regulators {
+ buck3210_reg: buck3210 {
+ /* VDD_CORE */
+ regulator-name = "buck3210";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
index 1683ec3..04df07f 100644
--- a/Documentation/devicetree/bindings/mfd/rk808.txt
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -3,11 +3,15 @@
The rk8xx family current members:
rk805
rk808
+rk809
+rk817
rk818
Required properties:
- compatible: "rockchip,rk805"
- compatible: "rockchip,rk808"
+- compatible: "rockchip,rk809"
+- compatible: "rockchip,rk817"
- compatible: "rockchip,rk818"
- reg: I2C slave address
- interrupts: the interrupt outputs of the controller.
@@ -45,6 +49,23 @@
the gpio controller. If DVS GPIOs aren't present, voltage changes will happen
very quickly with no slow ramp time.
+Optional shared RK809 and RK817 properties:
+- vcc1-supply: The input supply for DCDC_REG1
+- vcc2-supply: The input supply for DCDC_REG2
+- vcc3-supply: The input supply for DCDC_REG3
+- vcc4-supply: The input supply for DCDC_REG4
+- vcc5-supply: The input supply for LDO_REG1, LDO_REG2, LDO_REG3
+- vcc6-supply: The input supply for LDO_REG4, LDO_REG5, LDO_REG6
+- vcc7-supply: The input supply for LDO_REG7, LDO_REG8, LDO_REG9
+
+Optional RK809 properties:
+- vcc8-supply: The input supply for SWITCH_REG1
+- vcc9-supply: The input supply for DCDC_REG5, SWITCH_REG2
+
+Optional RK817 properties:
+- vcc8-supply: The input supply for BOOST
+- vcc9-supply: The input supply for OTG_SWITCH
+
Optional RK818 properties:
- vcc1-supply: The input supply for DCDC_REG1
- vcc2-supply: The input supply for DCDC_REG2
@@ -86,6 +107,21 @@
- SWITCH_REGn
- valid values for n are 1 to 2
+Following regulators of the RK809 and RK817 PMIC blocks are supported. Note that
+the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
+number as described in RK809 and RK817 datasheets.
+
+ - DCDC_REGn
+ - valid values for n are 1 to 5 for RK809.
+ - valid values for n are 1 to 4 for RK817.
+ - LDO_REGn
+ - valid values for n are 1 to 9 for RK809.
+ - valid values for n are 1 to 9 for RK817.
+ - SWITCH_REGn
+ - valid values for n are 1 to 2 for RK809.
+ - BOOST for RK817
+ - OTG_SWITCH for RK817
+
Following regulators of the RK818 PMIC block are supported. Note that
the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
number as described in RK818 datasheet.
@@ -98,6 +134,14 @@
- HDMI_SWITCH
- OTG_SWITCH
+It is necessary to configure three pins for both the RK809 and RK817, the three
+pins are "gpio_ts" "gpio_gt" "gpio_slp".
+ The gpio_gt and gpio_ts pins support the gpio function.
+ The gpio_slp pin is for controlling the pmic states, as below:
+ - reset
+ - power down
+ - sleep
+
Standard regulator bindings are used inside regulator subnodes. Check
Documentation/devicetree/bindings/regulator/regulator.txt
for more details
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index dd411c8..7376af2 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -53,13 +53,12 @@
This driver supports Maxim 9485 Programmable Audio Clock Generator
config COMMON_CLK_RK808
- tristate "Clock driver for RK805/RK808/RK818"
+ tristate "Clock driver for RK805/RK808/RK809/RK817/RK818"
depends on MFD_RK808
---help---
- This driver supports RK805, RK808 and RK818 crystal oscillator clock. These
- multi-function devices have two fixed-rate oscillators,
- clocked at 32KHz each. Clkout1 is always on, Clkout2 can off
- by control register.
+ This driver supports RK805, RK809 and RK817, RK808 and RK818 crystal oscillator clock.
+ These multi-function devices have two fixed-rate oscillators, clocked at 32KHz each.
+ Clkout1 is always on, Clkout2 can off by control register.
config COMMON_CLK_HI655X
tristate "Clock driver for Hi655x" if EXPERT
diff --git a/drivers/clk/clk-rk808.c b/drivers/clk/clk-rk808.c
index 8d90bdf..75f2cf0 100644
--- a/drivers/clk/clk-rk808.c
+++ b/drivers/clk/clk-rk808.c
@@ -96,6 +96,68 @@ of_clk_rk808_get(struct of_phandle_args *clkspec, void *data)
return idx ? &rk808_clkout->clkout2_hw : &rk808_clkout->clkout1_hw;
}
+static int rk817_clkout2_enable(struct clk_hw *hw, bool enable)
+{
+ struct rk808_clkout *rk808_clkout = container_of(hw,
+ struct rk808_clkout,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clkout->rk808;
+
+ return regmap_update_bits(rk808->regmap, RK817_SYS_CFG(1),
+ RK817_CLK32KOUT2_EN,
+ enable ? RK817_CLK32KOUT2_EN : 0);
+}
+
+static int rk817_clkout2_prepare(struct clk_hw *hw)
+{
+ return rk817_clkout2_enable(hw, true);
+}
+
+static void rk817_clkout2_unprepare(struct clk_hw *hw)
+{
+ rk817_clkout2_enable(hw, false);
+}
+
+static int rk817_clkout2_is_prepared(struct clk_hw *hw)
+{
+ struct rk808_clkout *rk808_clkout = container_of(hw,
+ struct rk808_clkout,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clkout->rk808;
+ unsigned int val;
+
+ int ret = regmap_read(rk808->regmap, RK817_SYS_CFG(1), &val);
+
+ if (ret < 0)
+ return 0;
+
+ return (val & RK817_CLK32KOUT2_EN) ? 1 : 0;
+}
+
+static const struct clk_ops rk817_clkout2_ops = {
+ .prepare = rk817_clkout2_prepare,
+ .unprepare = rk817_clkout2_unprepare,
+ .is_prepared = rk817_clkout2_is_prepared,
+ .recalc_rate = rk808_clkout_recalc_rate,
+};
+
+static const struct clk_ops *rkpmic_get_ops(long variant)
+{
+ switch (variant) {
+ case RK809_ID:
+ case RK817_ID:
+ return &rk817_clkout2_ops;
+ /*
+ * For the default case, it match the following PMIC type.
+ * RK805_ID
+ * RK808_ID
+ * RK818_ID
+ */
+ default:
+ return &rk808_clkout2_ops;
+ }
+}
+
static int rk808_clkout_probe(struct platform_device *pdev)
{
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
@@ -127,7 +189,7 @@ static int rk808_clkout_probe(struct platform_device *pdev)
return ret;
init.name = "rk808-clkout2";
- init.ops = &rk808_clkout2_ops;
+ init.ops = rkpmic_get_ops(rk808->variant);
rk808_clkout->clkout2_hw.init = &init;
/* optional override of the clockname */
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 11fc53d..760b9e2 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1030,14 +1030,14 @@
different functionality of the device.
config MFD_RK808
- tristate "Rockchip RK805/RK808/RK818 Power Management Chip"
+ tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
depends on I2C && OF
select MFD_CORE
select REGMAP_I2C
select REGMAP_IRQ
help
- If you say yes here you get support for the RK805, RK808 and RK818
- Power Management chips.
+ If you say yes here you get support for the RK805, RK808, RK809,
+ RK817 and RK818 Power Management chips.
This driver provides common support for accessing the device
through I2C interface. The device supports multiple sub-devices
including interrupts, RTC, LDO & DCDC regulators, and onkey.
diff --git a/drivers/mfd/lp87565.c b/drivers/mfd/lp87565.c
index 32d2a07..8ad688f 100644
--- a/drivers/mfd/lp87565.c
+++ b/drivers/mfd/lp87565.c
@@ -33,6 +33,10 @@ static const struct of_device_id of_lp87565_match_table[] = {
.compatible = "ti,lp87565-q1",
.data = (void *)LP87565_DEVICE_TYPE_LP87565_Q1,
},
+ {
+ .compatible = "ti,lp87561-q1",
+ .data = (void *)LP87565_DEVICE_TYPE_LP87561_Q1,
+ },
{}
};
MODULE_DEVICE_TABLE(of, of_lp87565_match_table);
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index 9437778..6ee1c46 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -27,6 +27,7 @@
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/regmap.h>
+#include <linux/syscore_ops.h>
struct rk808_reg_data {
int addr;
@@ -62,6 +63,27 @@ static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
return false;
}
+static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ /*
+ * Notes:
+ * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
+ * we don't use that feature. It's better to cache.
+ */
+
+ switch (reg) {
+ case RK817_SECONDS_REG ... RK817_WEEKS_REG:
+ case RK817_RTC_STATUS_REG:
+ case RK817_INT_STS_REG0:
+ case RK817_INT_STS_REG1:
+ case RK817_INT_STS_REG2:
+ case RK817_SYS_STS:
+ return true;
+ }
+
+ return true;
+}
+
static const struct regmap_config rk818_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
@@ -86,6 +108,14 @@ static const struct regmap_config rk808_regmap_config = {
.volatile_reg = rk808_is_volatile_reg,
};
+static const struct regmap_config rk817_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK817_GPIO_INT_CFG,
+ .cache_type = REGCACHE_NONE,
+ .volatile_reg = rk817_is_volatile_reg,
+};
+
static struct resource rtc_resources[] = {
{
.start = RK808_IRQ_RTC_ALARM,
@@ -94,6 +124,10 @@ static struct resource rtc_resources[] = {
}
};
+static struct resource rk817_rtc_resources[] = {
+ DEFINE_RES_IRQ(RK817_IRQ_RTC_ALARM),
+};
+
static struct resource rk805_key_resources[] = {
{
.start = RK805_IRQ_PWRON_FALL,
@@ -107,6 +141,11 @@ static struct resource rk805_key_resources[] = {
}
};
+static struct resource rk817_pwrkey_resources[] = {
+ DEFINE_RES_IRQ(RK817_IRQ_PWRON_RISE),
+ DEFINE_RES_IRQ(RK817_IRQ_PWRON_FALL),
+};
+
static const struct mfd_cell rk805s[] = {
{ .name = "rk808-clkout", },
{ .name = "rk808-regulator", },
@@ -132,6 +171,21 @@ static const struct mfd_cell rk808s[] = {
},
};
+static const struct mfd_cell rk817s[] = {
+ { .name = "rk808-clkout",},
+ { .name = "rk808-regulator",},
+ {
+ .name = "rk8xx-pwrkey",
+ .num_resources = ARRAY_SIZE(rk817_pwrkey_resources),
+ .resources = &rk817_pwrkey_resources[0],
+ },
+ {
+ .name = "rk808-rtc",
+ .num_resources = ARRAY_SIZE(rk817_rtc_resources),
+ .resources = &rk817_rtc_resources[0],
+ },
+};
+
static const struct mfd_cell rk818s[] = {
{ .name = "rk808-clkout", },
{ .name = "rk808-regulator", },
@@ -167,6 +221,13 @@ static const struct rk808_reg_data rk808_pre_init_reg[] = {
VB_LO_SEL_3500MV },
};
+static const struct rk808_reg_data rk817_pre_init_reg[] = {
+ {RK817_RTC_CTRL_REG, RTC_STOP, RTC_STOP},
+ {RK817_GPIO_INT_CFG, RK817_INT_POL_MSK, RK817_INT_POL_H},
+ {RK817_SYS_CFG(1), RK817_HOTDIE_TEMP_MSK | RK817_TSD_TEMP_MSK,
+ RK817_HOTDIE_105 | RK817_TSD_140},
+};
+
static const struct rk808_reg_data rk818_pre_init_reg[] = {
/* improve efficiency */
{ RK818_BUCK2_CONFIG_REG, BUCK2_RATE_MASK, BUCK_ILMIN_250MA },
@@ -332,6 +393,33 @@ static const struct regmap_irq rk818_irqs[] = {
},
};
+static const struct regmap_irq rk817_irqs[RK817_IRQ_END] = {
+ REGMAP_IRQ_REG_LINE(0, 8),
+ REGMAP_IRQ_REG_LINE(1, 8),
+ REGMAP_IRQ_REG_LINE(2, 8),
+ REGMAP_IRQ_REG_LINE(3, 8),
+ REGMAP_IRQ_REG_LINE(4, 8),
+ REGMAP_IRQ_REG_LINE(5, 8),
+ REGMAP_IRQ_REG_LINE(6, 8),
+ REGMAP_IRQ_REG_LINE(7, 8),
+ REGMAP_IRQ_REG_LINE(8, 8),
+ REGMAP_IRQ_REG_LINE(9, 8),
+ REGMAP_IRQ_REG_LINE(10, 8),
+ REGMAP_IRQ_REG_LINE(11, 8),
+ REGMAP_IRQ_REG_LINE(12, 8),
+ REGMAP_IRQ_REG_LINE(13, 8),
+ REGMAP_IRQ_REG_LINE(14, 8),
+ REGMAP_IRQ_REG_LINE(15, 8),
+ REGMAP_IRQ_REG_LINE(16, 8),
+ REGMAP_IRQ_REG_LINE(17, 8),
+ REGMAP_IRQ_REG_LINE(18, 8),
+ REGMAP_IRQ_REG_LINE(19, 8),
+ REGMAP_IRQ_REG_LINE(20, 8),
+ REGMAP_IRQ_REG_LINE(21, 8),
+ REGMAP_IRQ_REG_LINE(22, 8),
+ REGMAP_IRQ_REG_LINE(23, 8)
+};
+
static struct regmap_irq_chip rk805_irq_chip = {
.name = "rk805",
.irqs = rk805_irqs,
@@ -355,6 +443,18 @@ static const struct regmap_irq_chip rk808_irq_chip = {
.init_ack_masked = true,
};
+static struct regmap_irq_chip rk817_irq_chip = {
+ .name = "rk817",
+ .irqs = rk817_irqs,
+ .num_irqs = ARRAY_SIZE(rk817_irqs),
+ .num_regs = 3,
+ .irq_reg_stride = 2,
+ .status_base = RK817_INT_STS_REG0,
+ .mask_base = RK817_INT_STS_MSK_REG0,
+ .ack_base = RK817_INT_STS_REG0,
+ .init_ack_masked = true,
+};
+
static const struct regmap_irq_chip rk818_irq_chip = {
.name = "rk818",
.irqs = rk818_irqs,
@@ -423,9 +523,33 @@ static void rk818_device_shutdown(void)
dev_err(&rk808_i2c_client->dev, "power off error!\n");
}
+static void rk8xx_syscore_shutdown(void)
+{
+ struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
+ int ret;
+
+ if (system_state == SYSTEM_POWER_OFF &&
+ (rk808->variant == RK809_ID || rk808->variant == RK817_ID)) {
+ ret = regmap_update_bits(rk808->regmap,
+ RK817_SYS_CFG(3),
+ RK817_SLPPIN_FUNC_MSK,
+ SLPPIN_DN_FUN);
+ if (ret) {
+ dev_warn(&rk808_i2c_client->dev,
+ "Cannot switch to power down function\n");
+ }
+ }
+}
+
+static struct syscore_ops rk808_syscore_ops = {
+ .shutdown = rk8xx_syscore_shutdown,
+};
+
static const struct of_device_id rk808_of_match[] = {
{ .compatible = "rockchip,rk805" },
{ .compatible = "rockchip,rk808" },
+ { .compatible = "rockchip,rk809" },
+ { .compatible = "rockchip,rk817" },
{ .compatible = "rockchip,rk818" },
{ },
};
@@ -438,10 +562,11 @@ static int rk808_probe(struct i2c_client *client,
struct rk808 *rk808;
const struct rk808_reg_data *pre_init_reg;
const struct mfd_cell *cells;
- void (*pm_pwroff_fn)(void);
+ void (*pm_pwroff_fn)(void) = NULL;
int nr_pre_init_regs;
int nr_cells;
int pm_off = 0, msb, lsb;
+ unsigned char pmic_id_msb, pmic_id_lsb;
int ret;
int i;
@@ -449,15 +574,24 @@ static int rk808_probe(struct i2c_client *client,
if (!rk808)
return -ENOMEM;
+ if (of_device_is_compatible(np, "rockchip,rk817") ||
+ of_device_is_compatible(np, "rockchip,rk809")) {
+ pmic_id_msb = RK817_ID_MSB;
+ pmic_id_lsb = RK817_ID_LSB;
+ } else {
+ pmic_id_msb = RK808_ID_MSB;
+ pmic_id_lsb = RK808_ID_LSB;
+ }
+
/* Read chip variant */
- msb = i2c_smbus_read_byte_data(client, RK808_ID_MSB);
+ msb = i2c_smbus_read_byte_data(client, pmic_id_msb);
if (msb < 0) {
dev_err(&client->dev, "failed to read the chip id at 0x%x\n",
RK808_ID_MSB);
return msb;
}
- lsb = i2c_smbus_read_byte_data(client, RK808_ID_LSB);
+ lsb = i2c_smbus_read_byte_data(client, pmic_id_lsb);
if (lsb < 0) {
dev_err(&client->dev, "failed to read the chip id at 0x%x\n",
RK808_ID_LSB);
@@ -495,6 +629,16 @@ static int rk808_probe(struct i2c_client *client,
nr_cells = ARRAY_SIZE(rk818s);
pm_pwroff_fn = rk818_device_shutdown;
break;
+ case RK809_ID:
+ case RK817_ID:
+ rk808->regmap_cfg = &rk817_regmap_config;
+ rk808->regmap_irq_chip = &rk817_irq_chip;
+ pre_init_reg = rk817_pre_init_reg;
+ nr_pre_init_regs = ARRAY_SIZE(rk817_pre_init_reg);
+ cells = rk817s;
+ nr_cells = ARRAY_SIZE(rk817s);
+ register_syscore_ops(&rk808_syscore_ops);
+ break;
default:
dev_err(&client->dev, "Unsupported RK8XX ID %lu\n",
rk808->variant);
@@ -568,10 +712,52 @@ static int rk808_remove(struct i2c_client *client)
return 0;
}
+static int rk8xx_suspend(struct device *dev)
+{
+ struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
+ int ret = 0;
+
+ switch (rk808->variant) {
+ case RK809_ID:
+ case RK817_ID:
+ ret = regmap_update_bits(rk808->regmap,
+ RK817_SYS_CFG(3),
+ RK817_SLPPIN_FUNC_MSK,
+ SLPPIN_SLP_FUN);
+ break;
+ default:
+ break;
+ }
+
+ return ret;
+}
+
+static int rk8xx_resume(struct device *dev)
+{
+ struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
+ int ret = 0;
+
+ switch (rk808->variant) {
+ case RK809_ID:
+ case RK817_ID:
+ ret = regmap_update_bits(rk808->regmap,
+ RK817_SYS_CFG(3),
+ RK817_SLPPIN_FUNC_MSK,
+ SLPPIN_NULL_FUN);
+ break;
+ default:
+ break;
+ }
+
+ return ret;
+}
+SIMPLE_DEV_PM_OPS(rk8xx_pm_ops, rk8xx_suspend, rk8xx_resume);
+
static struct i2c_driver rk808_i2c_driver = {
.driver = {
.name = "rk808",
.of_match_table = rk808_of_match,
+ .pm = &rk8xx_pm_ops,
},
.probe = rk808_probe,
.remove = rk808_remove,
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 6c37f0d..214a958 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -762,11 +762,11 @@
outputs which can be controlled by i2c communication.
config REGULATOR_RK808
- tristate "Rockchip RK805/RK808/RK818 Power regulators"
+ tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power regulators"
depends on MFD_RK808
help
Select this option to enable the power regulator of ROCKCHIP
- PMIC RK805,RK808 and RK818.
+ PMIC RK805,RK809&RK817,RK808 and RK818.
This driver supports the control of different power rails of device
through regulator interface. The device supports multiple DCDC/LDO
outputs which can be controlled by i2c communication.
diff --git a/drivers/regulator/lp87565-regulator.c b/drivers/regulator/lp87565-regulator.c
index 81eb4b8..142b6f1 100644
--- a/drivers/regulator/lp87565-regulator.c
+++ b/drivers/regulator/lp87565-regulator.c
@@ -153,6 +153,12 @@ static const struct lp87565_regulator regulators[] = {
LP87565_REG_BUCK2_CTRL_1,
LP87565_BUCK_CTRL_1_EN, 3230,
buck0_1_2_3_ranges, LP87565_REG_BUCK2_CTRL_2),
+ LP87565_REGULATOR("BUCK3210", LP87565_BUCK_3210, "buck3210",
+ lp87565_buck_ops, 256, LP87565_REG_BUCK0_VOUT,
+ LP87565_BUCK_VSET, LP87565_REG_BUCK0_CTRL_1,
+ LP87565_BUCK_CTRL_1_EN |
+ LP87565_BUCK_CTRL_1_FPWM_MP_0_2, 3230,
+ buck0_1_2_3_ranges, LP87565_REG_BUCK0_CTRL_2),
};
static int lp87565_regulator_probe(struct platform_device *pdev)
@@ -169,9 +175,19 @@ static int lp87565_regulator_probe(struct platform_device *pdev)
config.driver_data = lp87565;
config.regmap = lp87565->regmap;
- if (lp87565->dev_type == LP87565_DEVICE_TYPE_LP87565_Q1) {
+ switch (lp87565->dev_type) {
+ case LP87565_DEVICE_TYPE_LP87565_Q1:
min_idx = LP87565_BUCK_10;
max_idx = LP87565_BUCK_23;
+ break;
+ case LP87565_DEVICE_TYPE_LP87561_Q1:
+ min_idx = LP87565_BUCK_3210;
+ max_idx = LP87565_BUCK_3210;
+ break;
+ default:
+ dev_err(lp87565->dev, "Invalid lp config %d\n",
+ lp87565->dev_type);
+ return -EINVAL;
}
for (i = min_idx; i <= max_idx; i++) {
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index 23713e1..e9b0bb9 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -36,6 +36,12 @@
#define RK808_BUCK4_VSEL_MASK 0xf
#define RK808_LDO_VSEL_MASK 0x1f
+#define RK809_BUCK5_VSEL_MASK 0x7
+
+#define RK817_LDO_VSEL_MASK 0x7f
+#define RK817_BOOST_VSEL_MASK 0x7
+#define RK817_BUCK_VSEL_MASK 0x7f
+
#define RK818_BUCK_VSEL_MASK 0x3f
#define RK818_BUCK4_VSEL_MASK 0x1f
#define RK818_LDO_VSEL_MASK 0x1f
@@ -65,30 +71,12 @@
/* max steps for increase voltage of Buck1/2, equal 100mv*/
#define MAX_STEPS_ONE_TIME 8
-#define RK805_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
- _vmask, _ereg, _emask, _etime) \
- [_id] = { \
- .name = (_match), \
- .supply_name = (_supply), \
- .of_match = of_match_ptr(_match), \
- .regulators_node = of_match_ptr("regulators"), \
- .type = REGULATOR_VOLTAGE, \
- .id = (_id), \
- .n_voltages = (((_max) - (_min)) / (_step) + 1), \
- .owner = THIS_MODULE, \
- .min_uV = (_min) * 1000, \
- .uV_step = (_step) * 1000, \
- .vsel_reg = (_vreg), \
- .vsel_mask = (_vmask), \
- .enable_reg = (_ereg), \
- .enable_mask = (_emask), \
- .enable_time = (_etime), \
- .ops = &rk805_reg_ops, \
- }
+#define ENABLE_MASK(id) (BIT(id) | BIT(4 + (id)))
+#define DISABLE_VAL(id) (BIT(4 + (id)))
-#define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
- _vmask, _ereg, _emask, _etime) \
- [_id] = { \
+#define RK817_BOOST_DESC(_id, _match, _supply, _min, _max, _step, _vreg,\
+ _vmask, _ereg, _emask, _enval, _disval, _etime, m_drop) \
+ { \
.name = (_match), \
.supply_name = (_supply), \
.of_match = of_match_ptr(_match), \
@@ -103,12 +91,54 @@
.vsel_mask = (_vmask), \
.enable_reg = (_ereg), \
.enable_mask = (_emask), \
+ .enable_val = (_enval), \
+ .disable_val = (_disval), \
.enable_time = (_etime), \
- .ops = &rk808_reg_ops, \
+ .min_dropout_uV = (m_drop) * 1000, \
+ .ops = &rk817_boost_ops, \
}
-#define RK8XX_DESC_SWITCH(_id, _match, _supply, _ereg, _emask) \
- [_id] = { \
+#define RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _enval, _disval, _etime, _ops) \
+ { \
+ .name = (_match), \
+ .supply_name = (_supply), \
+ .of_match = of_match_ptr(_match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .type = REGULATOR_VOLTAGE, \
+ .id = (_id), \
+ .n_voltages = (((_max) - (_min)) / (_step) + 1), \
+ .owner = THIS_MODULE, \
+ .min_uV = (_min) * 1000, \
+ .uV_step = (_step) * 1000, \
+ .vsel_reg = (_vreg), \
+ .vsel_mask = (_vmask), \
+ .enable_reg = (_ereg), \
+ .enable_mask = (_emask), \
+ .enable_val = (_enval), \
+ .disable_val = (_disval), \
+ .enable_time = (_etime), \
+ .ops = _ops, \
+ }
+
+#define RK805_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _etime) \
+ RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, 0, 0, _etime, &rk805_reg_ops)
+
+#define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _etime) \
+ RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, 0, 0, _etime, &rk808_reg_ops)
+
+#define RK817_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _disval, _etime) \
+ RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _emask, _disval, _etime, &rk817_reg_ops)
+
+#define RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \
+ _enval, _disval, _ops) \
+ { \
.name = (_match), \
.supply_name = (_supply), \
.of_match = of_match_ptr(_match), \
@@ -117,10 +147,20 @@
.id = (_id), \
.enable_reg = (_ereg), \
.enable_mask = (_emask), \
+ .enable_val = (_enval), \
+ .disable_val = (_disval), \
.owner = THIS_MODULE, \
- .ops = &rk808_switch_ops \
+ .ops = _ops \
}
+#define RK817_DESC_SWITCH(_id, _match, _supply, _ereg, _emask, \
+ _disval) \
+ RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \
+ _emask, _disval, &rk817_switch_ops)
+
+#define RK8XX_DESC_SWITCH(_id, _match, _supply, _ereg, _emask) \
+ RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \
+ 0, 0, &rk808_switch_ops)
struct rk808_regulator_data {
struct gpio_desc *dvs_gpio[2];
@@ -138,6 +178,51 @@ static const struct regulator_linear_range rk808_ldo3_voltage_ranges[] = {
REGULATOR_LINEAR_RANGE(2500000, 15, 15, 0),
};
+#define RK809_BUCK5_SEL_CNT (8)
+
+static const struct regulator_linear_range rk809_buck5_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1500000, 0, 0, 0),
+ REGULATOR_LINEAR_RANGE(1800000, 1, 3, 200000),
+ REGULATOR_LINEAR_RANGE(2800000, 4, 5, 200000),
+ REGULATOR_LINEAR_RANGE(3300000, 6, 7, 300000),
+};
+
+#define RK817_BUCK1_MIN0 500000
+#define RK817_BUCK1_MAX0 1500000
+
+#define RK817_BUCK1_MIN1 1600000
+#define RK817_BUCK1_MAX1 2400000
+
+#define RK817_BUCK3_MAX1 3400000
+
+#define RK817_BUCK1_STP0 12500
+#define RK817_BUCK1_STP1 100000
+
+#define RK817_BUCK1_SEL0 ((RK817_BUCK1_MAX0 - RK817_BUCK1_MIN0) /\
+ RK817_BUCK1_STP0)
+#define RK817_BUCK1_SEL1 ((RK817_BUCK1_MAX1 - RK817_BUCK1_MIN1) /\
+ RK817_BUCK1_STP1)
+
+#define RK817_BUCK3_SEL1 ((RK817_BUCK3_MAX1 - RK817_BUCK1_MIN1) /\
+ RK817_BUCK1_STP1)
+
+#define RK817_BUCK1_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK1_SEL1 + 1)
+#define RK817_BUCK3_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK3_SEL1 + 1)
+
+static const struct regulator_linear_range rk817_buck1_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0,
+ RK817_BUCK1_SEL0, RK817_BUCK1_STP0),
+ REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1,
+ RK817_BUCK1_SEL_CNT, RK817_BUCK1_STP1),
+};
+
+static const struct regulator_linear_range rk817_buck3_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0,
+ RK817_BUCK1_SEL0, RK817_BUCK1_STP0),
+ REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1,
+ RK817_BUCK3_SEL_CNT, RK817_BUCK1_STP1),
+};
+
static int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev)
{
struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
@@ -289,6 +374,36 @@ static int rk808_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
RK808_RAMP_RATE_MASK, ramp_value);
}
+/*
+ * RK817 RK809
+ */
+static int rk817_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+ unsigned int ramp_value = RK817_RAMP_RATE_25MV_PER_US;
+ unsigned int reg = RK817_BUCK_CONFIG_REG(rdev_get_id(rdev));
+
+ switch (ramp_delay) {
+ case 0 ... 3000:
+ ramp_value = RK817_RAMP_RATE_3MV_PER_US;
+ break;
+ case 3001 ... 6300:
+ ramp_value = RK817_RAMP_RATE_6_3MV_PER_US;
+ break;
+ case 6301 ... 12500:
+ ramp_value = RK817_RAMP_RATE_12_5MV_PER_US;
+ break;
+ case 12501 ... 25000:
+ break;
+ default:
+ dev_warn(&rdev->dev,
+ "%s ramp_delay: %d not supported, setting 10000\n",
+ rdev->desc->name, ramp_delay);
+ }
+
+ return regmap_update_bits(rdev->regmap, reg,
+ RK817_RAMP_RATE_MASK, ramp_value);
+}
+
static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv)
{
unsigned int reg;
@@ -304,6 +419,21 @@ static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv)
sel);
}
+static int rk817_set_suspend_voltage(struct regulator_dev *rdev, int uv)
+{
+ unsigned int reg;
+ int sel = regulator_map_voltage_linear(rdev, uv, uv);
+ /* only ldo1~ldo9 */
+ if (sel < 0)
+ return -EINVAL;
+
+ reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
+
+ return regmap_update_bits(rdev->regmap, reg,
+ rdev->desc->vsel_mask,
+ sel);
+}
+
static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv)
{
unsigned int reg;
@@ -363,6 +493,131 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
rdev->desc->enable_mask);
}
+static int rk817_set_suspend_enable_ctrl(struct regulator_dev *rdev,
+ unsigned int en)
+{
+ unsigned int reg;
+ int id = rdev_get_id(rdev);
+ unsigned int id_slp, msk, val;
+
+ if (id >= RK817_ID_DCDC1 && id <= RK817_ID_DCDC4)
+ id_slp = id;
+ else if (id >= RK817_ID_LDO1 && id <= RK817_ID_LDO8)
+ id_slp = 8 + (id - RK817_ID_LDO1);
+ else if (id >= RK817_ID_LDO9 && id <= RK809_ID_SW2)
+ id_slp = 4 + (id - RK817_ID_LDO9);
+ else
+ return -EINVAL;
+
+ reg = RK817_POWER_SLP_EN_REG(id_slp / 8);
+
+ msk = BIT(id_slp % 8);
+ if (en)
+ val = msk;
+ else
+ val = 0;
+
+ return regmap_update_bits(rdev->regmap, reg, msk, val);
+}
+
+static int rk817_set_suspend_enable(struct regulator_dev *rdev)
+{
+ return rk817_set_suspend_enable_ctrl(rdev, 1);
+}
+
+static int rk817_set_suspend_disable(struct regulator_dev *rdev)
+{
+ return rk817_set_suspend_enable_ctrl(rdev, 0);
+}
+
+static int rk8xx_set_suspend_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ unsigned int reg;
+
+ reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ return regmap_update_bits(rdev->regmap, reg,
+ PWM_MODE_MSK, FPWM_MODE);
+ case REGULATOR_MODE_NORMAL:
+ return regmap_update_bits(rdev->regmap, reg,
+ PWM_MODE_MSK, AUTO_PWM_MODE);
+ default:
+ dev_err(&rdev->dev, "do not support this mode\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int rk8xx_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+ PWM_MODE_MSK, FPWM_MODE);
+ case REGULATOR_MODE_NORMAL:
+ return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+ PWM_MODE_MSK, AUTO_PWM_MODE);
+ default:
+ dev_err(&rdev->dev, "do not support this mode\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static unsigned int rk8xx_get_mode(struct regulator_dev *rdev)
+{
+ unsigned int val;
+ int err;
+
+ err = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
+ if (err)
+ return err;
+
+ if (val & FPWM_MODE)
+ return REGULATOR_MODE_FAST;
+ else
+ return REGULATOR_MODE_NORMAL;
+}
+
+static int rk8xx_is_enabled_wmsk_regmap(struct regulator_dev *rdev)
+{
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val);
+ if (ret != 0)
+ return ret;
+
+ /* add write mask bit */
+ val |= (rdev->desc->enable_mask & 0xf0);
+ val &= rdev->desc->enable_mask;
+
+ if (rdev->desc->enable_is_inverted) {
+ if (rdev->desc->enable_val)
+ return val != rdev->desc->enable_val;
+ return (val == 0);
+ }
+ if (rdev->desc->enable_val)
+ return val == rdev->desc->enable_val;
+ return val != 0;
+}
+
+static unsigned int rk8xx_regulator_of_map_mode(unsigned int mode)
+{
+ switch (mode) {
+ case 1:
+ return REGULATOR_MODE_FAST;
+ case 2:
+ return REGULATOR_MODE_NORMAL;
+ default:
+ return -EINVAL;
+ }
+}
+
static const struct regulator_ops rk805_reg_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
@@ -439,6 +694,71 @@ static const struct regulator_linear_range rk805_buck_1_2_voltage_ranges[] = {
REGULATOR_LINEAR_RANGE(2300000, 63, 63, 0),
};
+static struct regulator_ops rk809_buck5_ops_range = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+ .set_suspend_voltage = rk808_set_suspend_voltage_range,
+ .set_suspend_enable = rk817_set_suspend_enable,
+ .set_suspend_disable = rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_reg_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+ .set_suspend_voltage = rk817_set_suspend_voltage,
+ .set_suspend_enable = rk817_set_suspend_enable,
+ .set_suspend_disable = rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_boost_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+ .set_suspend_enable = rk817_set_suspend_enable,
+ .set_suspend_disable = rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_buck_ops_range = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+ .set_mode = rk8xx_set_mode,
+ .get_mode = rk8xx_get_mode,
+ .set_suspend_mode = rk8xx_set_suspend_mode,
+ .set_ramp_delay = rk817_set_ramp_delay,
+ .set_suspend_voltage = rk808_set_suspend_voltage_range,
+ .set_suspend_enable = rk817_set_suspend_enable,
+ .set_suspend_disable = rk817_set_suspend_disable,
+};
+
+static struct regulator_ops rk817_switch_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+ .set_suspend_enable = rk817_set_suspend_enable,
+ .set_suspend_disable = rk817_set_suspend_disable,
+};
+
static const struct regulator_desc rk805_reg[] = {
{
.name = "DCDC_REG1",
@@ -595,6 +915,271 @@ static const struct regulator_desc rk808_reg[] = {
RK808_DCDC_EN_REG, BIT(6)),
};
+static const struct regulator_desc rk809_reg[] = {
+ {
+ .name = "DCDC_REG1",
+ .supply_name = "vcc1",
+ .of_match = of_match_ptr("DCDC_REG1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC1,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK1_SEL_CNT + 1,
+ .linear_ranges = rk817_buck1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+ .vsel_reg = RK817_BUCK1_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC1),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC1),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC1),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG2",
+ .supply_name = "vcc2",
+ .of_match = of_match_ptr("DCDC_REG2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC2,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK1_SEL_CNT + 1,
+ .linear_ranges = rk817_buck1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+ .vsel_reg = RK817_BUCK2_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC2),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC2),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC2),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG3",
+ .supply_name = "vcc3",
+ .of_match = of_match_ptr("DCDC_REG3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC3,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK1_SEL_CNT + 1,
+ .linear_ranges = rk817_buck1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+ .vsel_reg = RK817_BUCK3_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC3),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC3),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC3),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG4",
+ .supply_name = "vcc4",
+ .of_match = of_match_ptr("DCDC_REG4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC4,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK3_SEL_CNT + 1,
+ .linear_ranges = rk817_buck3_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges),
+ .vsel_reg = RK817_BUCK4_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC4),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC4),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC4),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "DCDC_REG5",
+ .supply_name = "vcc9",
+ .of_match = of_match_ptr("DCDC_REG5"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK809_ID_DCDC5,
+ .ops = &rk809_buck5_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK809_BUCK5_SEL_CNT,
+ .linear_ranges = rk809_buck5_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk809_buck5_voltage_ranges),
+ .vsel_reg = RK809_BUCK5_CONFIG(0),
+ .vsel_mask = RK809_BUCK5_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(3),
+ .enable_mask = ENABLE_MASK(1),
+ .enable_val = ENABLE_MASK(1),
+ .disable_val = DISABLE_VAL(1),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ },
+ RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(0),
+ DISABLE_VAL(0), 400),
+ RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(1),
+ DISABLE_VAL(1), 400),
+ RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(2),
+ DISABLE_VAL(2), 400),
+ RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(3),
+ DISABLE_VAL(3), 400),
+ RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(0),
+ DISABLE_VAL(0), 400),
+ RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(1),
+ DISABLE_VAL(1), 400),
+ RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(2),
+ DISABLE_VAL(2), 400),
+ RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(3),
+ DISABLE_VAL(3), 400),
+ RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(3), ENABLE_MASK(0),
+ DISABLE_VAL(0), 400),
+ RK817_DESC_SWITCH(RK809_ID_SW1, "SWITCH_REG1", "vcc9",
+ RK817_POWER_EN_REG(3), ENABLE_MASK(2),
+ DISABLE_VAL(2)),
+ RK817_DESC_SWITCH(RK809_ID_SW2, "SWITCH_REG2", "vcc8",
+ RK817_POWER_EN_REG(3), ENABLE_MASK(3),
+ DISABLE_VAL(3)),
+};
+
+static const struct regulator_desc rk817_reg[] = {
+ {
+ .name = "DCDC_REG1",
+ .supply_name = "vcc1",
+ .of_match = of_match_ptr("DCDC_REG1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC1,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK1_SEL_CNT + 1,
+ .linear_ranges = rk817_buck1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+ .vsel_reg = RK817_BUCK1_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC1),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC1),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC1),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG2",
+ .supply_name = "vcc2",
+ .of_match = of_match_ptr("DCDC_REG2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC2,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK1_SEL_CNT + 1,
+ .linear_ranges = rk817_buck1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+ .vsel_reg = RK817_BUCK2_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC2),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC2),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC2),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG3",
+ .supply_name = "vcc3",
+ .of_match = of_match_ptr("DCDC_REG3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC3,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK1_SEL_CNT + 1,
+ .linear_ranges = rk817_buck1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
+ .vsel_reg = RK817_BUCK3_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC3),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC3),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC3),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG4",
+ .supply_name = "vcc4",
+ .of_match = of_match_ptr("DCDC_REG4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK817_ID_DCDC4,
+ .ops = &rk817_buck_ops_range,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = RK817_BUCK3_SEL_CNT + 1,
+ .linear_ranges = rk817_buck3_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges),
+ .vsel_reg = RK817_BUCK4_ON_VSEL_REG,
+ .vsel_mask = RK817_BUCK_VSEL_MASK,
+ .enable_reg = RK817_POWER_EN_REG(0),
+ .enable_mask = ENABLE_MASK(RK817_ID_DCDC4),
+ .enable_val = ENABLE_MASK(RK817_ID_DCDC4),
+ .disable_val = DISABLE_VAL(RK817_ID_DCDC4),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ },
+ RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(0),
+ DISABLE_VAL(0), 400),
+ RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(1),
+ DISABLE_VAL(1), 400),
+ RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(2),
+ DISABLE_VAL(2), 400),
+ RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(1), ENABLE_MASK(3),
+ DISABLE_VAL(3), 400),
+ RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(0),
+ DISABLE_VAL(0), 400),
+ RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(1),
+ DISABLE_VAL(1), 400),
+ RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(2),
+ DISABLE_VAL(2), 400),
+ RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(2), ENABLE_MASK(3),
+ DISABLE_VAL(3), 400),
+ RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25,
+ RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK,
+ RK817_POWER_EN_REG(3), ENABLE_MASK(0),
+ DISABLE_VAL(0), 400),
+ RK817_BOOST_DESC(RK817_ID_BOOST, "BOOST", "vcc8", 4700, 5400, 100,
+ RK817_BOOST_OTG_CFG, RK817_BOOST_VSEL_MASK,
+ RK817_POWER_EN_REG(3), ENABLE_MASK(1), ENABLE_MASK(1),
+ DISABLE_VAL(1), 400, 3500 - 5400),
+ RK817_DESC_SWITCH(RK817_ID_BOOST_OTG_SW, "OTG_SWITCH", "vcc9",
+ RK817_POWER_EN_REG(3), ENABLE_MASK(2),
+ DISABLE_VAL(2)),
+};
+
static const struct regulator_desc rk818_reg[] = {
{
.name = "DCDC_REG1",
@@ -765,6 +1350,14 @@ static int rk808_regulator_probe(struct platform_device *pdev)
regulators = rk808_reg;
nregulators = RK808_NUM_REGULATORS;
break;
+ case RK809_ID:
+ regulators = rk809_reg;
+ nregulators = RK809_NUM_REGULATORS;
+ break;
+ case RK817_ID:
+ regulators = rk817_reg;
+ nregulators = RK817_NUM_REGULATORS;
+ break;
case RK818_ID:
regulators = rk818_reg;
nregulators = RK818_NUM_REGULATORS;
@@ -803,6 +1396,7 @@ static struct platform_driver rk808_regulator_driver = {
module_platform_driver(rk808_regulator_driver);
MODULE_DESCRIPTION("regulator driver for the RK805/RK808/RK818 series PMICs");
+MODULE_AUTHOR("Tony xie <tony.xie@rock-chips.com>");
MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 060803a..bd673dd 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -373,11 +373,11 @@
will be called rtc-max77686.
config RTC_DRV_RK808
- tristate "Rockchip RK805/RK808/RK818 RTC"
+ tristate "Rockchip RK805/RK808/RK809/RK817/RK818 RTC"
depends on MFD_RK808
help
If you say yes here you will get support for the
- RTC of RK805, RK808 and RK818 PMIC.
+ RTC of RK805, RK809 and RK817, RK808 and RK818 PMIC.
This driver can also be built as a module. If so, the module
will be called rk808-rtc.
diff --git a/drivers/rtc/rtc-rk808.c b/drivers/rtc/rtc-rk808.c
index 5c5d9f1..6c6d674 100644
--- a/drivers/rtc/rtc-rk808.c
+++ b/drivers/rtc/rtc-rk808.c
@@ -50,9 +50,18 @@
#define NUM_TIME_REGS (RK808_WEEKS_REG - RK808_SECONDS_REG + 1)
#define NUM_ALARM_REGS (RK808_ALARM_YEARS_REG - RK808_ALARM_SECONDS_REG + 1)
+struct rk_rtc_compat_reg {
+ unsigned int ctrl_reg;
+ unsigned int status_reg;
+ unsigned int alarm_seconds_reg;
+ unsigned int int_reg;
+ unsigned int seconds_reg;
+};
+
struct rk808_rtc {
struct rk808 *rk808;
struct rtc_device *rtc;
+ struct rk_rtc_compat_reg *creg;
int irq;
};
@@ -101,7 +110,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
int ret;
/* Force an update of the shadowed registers right now */
- ret = regmap_update_bits(rk808->regmap, RK808_RTC_CTRL_REG,
+ ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_RTC_GET_TIME,
BIT_RTC_CTRL_REG_RTC_GET_TIME);
if (ret) {
@@ -115,7 +124,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
* 32khz. If we clear the GET_TIME bit here, the time of i2c transfer
* certainly more than 31.25us: 16 * 2.5us at 400kHz bus frequency.
*/
- ret = regmap_update_bits(rk808->regmap, RK808_RTC_CTRL_REG,
+ ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_RTC_GET_TIME,
0);
if (ret) {
@@ -123,7 +132,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
return ret;
}
- ret = regmap_bulk_read(rk808->regmap, RK808_SECONDS_REG,
+ ret = regmap_bulk_read(rk808->regmap, rk808_rtc->creg->seconds_reg,
rtc_data, NUM_TIME_REGS);
if (ret) {
dev_err(dev, "Failed to bulk read rtc_data: %d\n", ret);
@@ -162,7 +171,7 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
rtc_data[6] = bin2bcd(tm->tm_wday);
/* Stop RTC while updating the RTC registers */
- ret = regmap_update_bits(rk808->regmap, RK808_RTC_CTRL_REG,
+ ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M,
BIT_RTC_CTRL_REG_STOP_RTC_M);
if (ret) {
@@ -170,14 +179,14 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
return ret;
}
- ret = regmap_bulk_write(rk808->regmap, RK808_SECONDS_REG,
+ ret = regmap_bulk_write(rk808->regmap, rk808_rtc->creg->seconds_reg,
rtc_data, NUM_TIME_REGS);
if (ret) {
dev_err(dev, "Failed to bull write rtc_data: %d\n", ret);
return ret;
}
/* Start RTC again */
- ret = regmap_update_bits(rk808->regmap, RK808_RTC_CTRL_REG,
+ ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M, 0);
if (ret) {
dev_err(dev, "Failed to update RTC control: %d\n", ret);
@@ -195,8 +204,13 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
uint32_t int_reg;
int ret;
- ret = regmap_bulk_read(rk808->regmap, RK808_ALARM_SECONDS_REG,
+ ret = regmap_bulk_read(rk808->regmap,
+ rk808_rtc->creg->alarm_seconds_reg,
alrm_data, NUM_ALARM_REGS);
+ if (ret) {
+ dev_err(dev, "Failed to read RTC alarm date REG: %d\n", ret);
+ return ret;
+ }
alrm->time.tm_sec = bcd2bin(alrm_data[0] & SECONDS_REG_MSK);
alrm->time.tm_min = bcd2bin(alrm_data[1] & MINUTES_REG_MAK);
@@ -206,7 +220,7 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
alrm->time.tm_year = (bcd2bin(alrm_data[5] & YEARS_REG_MSK)) + 100;
rockchip_to_gregorian(&alrm->time);
- ret = regmap_read(rk808->regmap, RK808_RTC_INT_REG, &int_reg);
+ ret = regmap_read(rk808->regmap, rk808_rtc->creg->int_reg, &int_reg);
if (ret) {
dev_err(dev, "Failed to read RTC INT REG: %d\n", ret);
return ret;
@@ -225,7 +239,7 @@ static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
struct rk808 *rk808 = rk808_rtc->rk808;
int ret;
- ret = regmap_update_bits(rk808->regmap, RK808_RTC_INT_REG,
+ ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M, 0);
return ret;
@@ -236,7 +250,7 @@ static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
struct rk808 *rk808 = rk808_rtc->rk808;
int ret;
- ret = regmap_update_bits(rk808->regmap, RK808_RTC_INT_REG,
+ ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
@@ -266,7 +280,8 @@ static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
alrm_data[4] = bin2bcd(alrm->time.tm_mon + 1);
alrm_data[5] = bin2bcd(alrm->time.tm_year - 100);
- ret = regmap_bulk_write(rk808->regmap, RK808_ALARM_SECONDS_REG,
+ ret = regmap_bulk_write(rk808->regmap,
+ rk808_rtc->creg->alarm_seconds_reg,
alrm_data, NUM_ALARM_REGS);
if (ret) {
dev_err(dev, "Failed to bulk write: %d\n", ret);
@@ -310,7 +325,7 @@ static irqreturn_t rk808_alarm_irq(int irq, void *data)
struct i2c_client *client = rk808->i2c;
int ret;
- ret = regmap_write(rk808->regmap, RK808_RTC_STATUS_REG,
+ ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
RTC_STATUS_MASK);
if (ret) {
dev_err(&client->dev,
@@ -361,6 +376,22 @@ static int rk808_rtc_resume(struct device *dev)
static SIMPLE_DEV_PM_OPS(rk808_rtc_pm_ops,
rk808_rtc_suspend, rk808_rtc_resume);
+static struct rk_rtc_compat_reg rk808_creg = {
+ .ctrl_reg = RK808_RTC_CTRL_REG,
+ .status_reg = RK808_RTC_STATUS_REG,
+ .alarm_seconds_reg = RK808_ALARM_SECONDS_REG,
+ .int_reg = RK808_RTC_INT_REG,
+ .seconds_reg = RK808_SECONDS_REG,
+};
+
+static struct rk_rtc_compat_reg rk817_creg = {
+ .ctrl_reg = RK817_RTC_CTRL_REG,
+ .status_reg = RK817_RTC_STATUS_REG,
+ .alarm_seconds_reg = RK817_ALARM_SECONDS_REG,
+ .int_reg = RK817_RTC_INT_REG,
+ .seconds_reg = RK817_SECONDS_REG,
+};
+
static int rk808_rtc_probe(struct platform_device *pdev)
{
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
@@ -371,11 +402,20 @@ static int rk808_rtc_probe(struct platform_device *pdev)
if (rk808_rtc == NULL)
return -ENOMEM;
+ switch (rk808->variant) {
+ case RK809_ID:
+ case RK817_ID:
+ rk808_rtc->creg = &rk817_creg;
+ break;
+ default:
+ rk808_rtc->creg = &rk808_creg;
+ break;
+ }
platform_set_drvdata(pdev, rk808_rtc);
rk808_rtc->rk808 = rk808;
/* start rtc running by default, and use shadowed timer. */
- ret = regmap_update_bits(rk808->regmap, RK808_RTC_CTRL_REG,
+ ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M |
BIT_RTC_CTRL_REG_RTC_READSEL_M,
BIT_RTC_CTRL_REG_RTC_READSEL_M);
@@ -385,7 +425,7 @@ static int rk808_rtc_probe(struct platform_device *pdev)
return ret;
}
- ret = regmap_write(rk808->regmap, RK808_RTC_STATUS_REG,
+ ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
RTC_STATUS_MASK);
if (ret) {
dev_err(&pdev->dev,
diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h
index dcec96f..fa39772 100644
--- a/include/linux/mfd/cros_ec_commands.h
+++ b/include/linux/mfd/cros_ec_commands.h
@@ -1,28 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Host communication command constants for ChromeOS EC
*
* Copyright (C) 2012 Google, Inc
*
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * The ChromeOS EC multi function device is used to mux all the requests
- * to the EC device for its multiple features: keyboard controller,
- * battery charging and regulator control, firmware update.
- *
- * NOTE: This file is copied verbatim from the ChromeOS EC Open Source
- * project in an attempt to make future updates easy to make.
+ * NOTE: This file is auto-generated from ChromeOS EC Open Source code from
+ * https://chromium.googlesource.com/chromiumos/platform/ec/+/master/include/ec_commands.h
*/
+/* Host communication command constants for Chrome EC */
+
#ifndef __CROS_EC_COMMANDS_H
#define __CROS_EC_COMMANDS_H
+
+
+
+#define BUILD_ASSERT(_cond)
+
/*
* Current version of this protocol
*
@@ -33,7 +28,7 @@
#define EC_PROTO_VERSION 0x00000002
/* Command version mask */
-#define EC_VER_MASK(version) (1UL << (version))
+#define EC_VER_MASK(version) BIT(version)
/* I/O addresses for ACPI commands */
#define EC_LPC_ADDR_ACPI_DATA 0x62
@@ -47,25 +42,28 @@
/* Protocol version 2 */
#define EC_LPC_ADDR_HOST_ARGS 0x800 /* And 0x801, 0x802, 0x803 */
#define EC_LPC_ADDR_HOST_PARAM 0x804 /* For version 2 params; size is
- * EC_PROTO2_MAX_PARAM_SIZE */
+ * EC_PROTO2_MAX_PARAM_SIZE
+ */
/* Protocol version 3 */
#define EC_LPC_ADDR_HOST_PACKET 0x800 /* Offset of version 3 packet */
#define EC_LPC_HOST_PACKET_SIZE 0x100 /* Max size of version 3 packet */
-/* The actual block is 0x800-0x8ff, but some BIOSes think it's 0x880-0x8ff
- * and they tell the kernel that so we have to think of it as two parts. */
+/*
+ * The actual block is 0x800-0x8ff, but some BIOSes think it's 0x880-0x8ff
+ * and they tell the kernel that so we have to think of it as two parts.
+ */
#define EC_HOST_CMD_REGION0 0x800
#define EC_HOST_CMD_REGION1 0x880
#define EC_HOST_CMD_REGION_SIZE 0x80
/* EC command register bit functions */
-#define EC_LPC_CMDR_DATA (1 << 0) /* Data ready for host to read */
-#define EC_LPC_CMDR_PENDING (1 << 1) /* Write pending to EC */
-#define EC_LPC_CMDR_BUSY (1 << 2) /* EC is busy processing a command */
-#define EC_LPC_CMDR_CMD (1 << 3) /* Last host write was a command */
-#define EC_LPC_CMDR_ACPI_BRST (1 << 4) /* Burst mode (not used) */
-#define EC_LPC_CMDR_SCI (1 << 5) /* SCI event is pending */
-#define EC_LPC_CMDR_SMI (1 << 6) /* SMI event is pending */
+#define EC_LPC_CMDR_DATA BIT(0) /* Data ready for host to read */
+#define EC_LPC_CMDR_PENDING BIT(1) /* Write pending to EC */
+#define EC_LPC_CMDR_BUSY BIT(2) /* EC is busy processing a command */
+#define EC_LPC_CMDR_CMD BIT(3) /* Last host write was a command */
+#define EC_LPC_CMDR_ACPI_BRST BIT(4) /* Burst mode (not used) */
+#define EC_LPC_CMDR_SCI BIT(5) /* SCI event is pending */
+#define EC_LPC_CMDR_SMI BIT(6) /* SMI event is pending */
#define EC_LPC_ADDR_MEMMAP 0x900
#define EC_MEMMAP_SIZE 255 /* ACPI IO buffer max is 255 bytes */
@@ -85,13 +83,15 @@
/* Unused 0x28 - 0x2f */
#define EC_MEMMAP_SWITCHES 0x30 /* 8 bits */
/* Unused 0x31 - 0x33 */
-#define EC_MEMMAP_HOST_EVENTS 0x34 /* 32 bits */
-/* Reserve 0x38 - 0x3f for additional host event-related stuff */
-/* Battery values are all 32 bits */
+#define EC_MEMMAP_HOST_EVENTS 0x34 /* 64 bits */
+/* Battery values are all 32 bits, unless otherwise noted. */
#define EC_MEMMAP_BATT_VOLT 0x40 /* Battery Present Voltage */
#define EC_MEMMAP_BATT_RATE 0x44 /* Battery Present Rate */
#define EC_MEMMAP_BATT_CAP 0x48 /* Battery Remaining Capacity */
-#define EC_MEMMAP_BATT_FLAG 0x4c /* Battery State, defined below */
+#define EC_MEMMAP_BATT_FLAG 0x4c /* Battery State, see below (8-bit) */
+#define EC_MEMMAP_BATT_COUNT 0x4d /* Battery Count (8-bit) */
+#define EC_MEMMAP_BATT_INDEX 0x4e /* Current Battery Data Index (8-bit) */
+/* Unused 0x4f */
#define EC_MEMMAP_BATT_DCAP 0x50 /* Battery Design Capacity */
#define EC_MEMMAP_BATT_DVLT 0x54 /* Battery Design Voltage */
#define EC_MEMMAP_BATT_LFCC 0x58 /* Battery Last Full Charge Capacity */
@@ -105,15 +105,24 @@
/* Unused 0x84 - 0x8f */
#define EC_MEMMAP_ACC_STATUS 0x90 /* Accelerometer status (8 bits )*/
/* Unused 0x91 */
-#define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometer data 0x92 - 0x9f */
+#define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometers data 0x92 - 0x9f */
+/* 0x92: Lid Angle if available, LID_ANGLE_UNRELIABLE otherwise */
+/* 0x94 - 0x99: 1st Accelerometer */
+/* 0x9a - 0x9f: 2nd Accelerometer */
#define EC_MEMMAP_GYRO_DATA 0xa0 /* Gyroscope data 0xa0 - 0xa5 */
-/* Unused 0xa6 - 0xfe (remember, 0xff is NOT part of the memmap region) */
+/* Unused 0xa6 - 0xdf */
+/*
+ * ACPI is unable to access memory mapped data at or above this offset due to
+ * limitations of the ACPI protocol. Do not place data in the range 0xe0 - 0xfe
+ * which might be needed by ACPI.
+ */
+#define EC_MEMMAP_NO_ACPI 0xe0
/* Define the format of the accelerometer mapped memory status byte. */
#define EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK 0x0f
-#define EC_MEMMAP_ACC_STATUS_BUSY_BIT (1 << 4)
-#define EC_MEMMAP_ACC_STATUS_PRESENCE_BIT (1 << 7)
+#define EC_MEMMAP_ACC_STATUS_BUSY_BIT BIT(4)
+#define EC_MEMMAP_ACC_STATUS_PRESENCE_BIT BIT(7)
/* Number of temp sensors at EC_MEMMAP_TEMP_SENSOR */
#define EC_TEMP_SENSOR_ENTRIES 16
@@ -157,6 +166,8 @@
#define EC_BATT_FLAG_DISCHARGING 0x04
#define EC_BATT_FLAG_CHARGING 0x08
#define EC_BATT_FLAG_LEVEL_CRITICAL 0x10
+/* Set if some of the static/dynamic data is invalid (or outdated). */
+#define EC_BATT_FLAG_INVALID_DATA 0x20
/* Switch flags at EC_MEMMAP_SWITCHES */
#define EC_SWITCH_LID_OPEN 0x01
@@ -182,20 +193,242 @@
#define EC_WIRELESS_SWITCH_WWAN 0x04 /* WWAN power */
#define EC_WIRELESS_SWITCH_WLAN_POWER 0x08 /* WLAN power */
+/*****************************************************************************/
+/*
+ * ACPI commands
+ *
+ * These are valid ONLY on the ACPI command/data port.
+ */
+
+/*
+ * ACPI Read Embedded Controller
+ *
+ * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
+ *
+ * Use the following sequence:
+ *
+ * - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD
+ * - Wait for EC_LPC_CMDR_PENDING bit to clear
+ * - Write address to EC_LPC_ADDR_ACPI_DATA
+ * - Wait for EC_LPC_CMDR_DATA bit to set
+ * - Read value from EC_LPC_ADDR_ACPI_DATA
+ */
+#define EC_CMD_ACPI_READ 0x0080
+
+/*
+ * ACPI Write Embedded Controller
+ *
+ * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
+ *
+ * Use the following sequence:
+ *
+ * - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD
+ * - Wait for EC_LPC_CMDR_PENDING bit to clear
+ * - Write address to EC_LPC_ADDR_ACPI_DATA
+ * - Wait for EC_LPC_CMDR_PENDING bit to clear
+ * - Write value to EC_LPC_ADDR_ACPI_DATA
+ */
+#define EC_CMD_ACPI_WRITE 0x0081
+
+/*
+ * ACPI Burst Enable Embedded Controller
+ *
+ * This enables burst mode on the EC to allow the host to issue several
+ * commands back-to-back. While in this mode, writes to mapped multi-byte
+ * data are locked out to ensure data consistency.
+ */
+#define EC_CMD_ACPI_BURST_ENABLE 0x0082
+
+/*
+ * ACPI Burst Disable Embedded Controller
+ *
+ * This disables burst mode on the EC and stops preventing EC writes to mapped
+ * multi-byte data.
+ */
+#define EC_CMD_ACPI_BURST_DISABLE 0x0083
+
+/*
+ * ACPI Query Embedded Controller
+ *
+ * This clears the lowest-order bit in the currently pending host events, and
+ * sets the result code to the 1-based index of the bit (event 0x00000001 = 1,
+ * event 0x80000000 = 32), or 0 if no event was pending.
+ */
+#define EC_CMD_ACPI_QUERY_EVENT 0x0084
+
+/* Valid addresses in ACPI memory space, for read/write commands */
+
+/* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */
+#define EC_ACPI_MEM_VERSION 0x00
+/*
+ * Test location; writing value here updates test compliment byte to (0xff -
+ * value).
+ */
+#define EC_ACPI_MEM_TEST 0x01
+/* Test compliment; writes here are ignored. */
+#define EC_ACPI_MEM_TEST_COMPLIMENT 0x02
+
+/* Keyboard backlight brightness percent (0 - 100) */
+#define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03
+/* DPTF Target Fan Duty (0-100, 0xff for auto/none) */
+#define EC_ACPI_MEM_FAN_DUTY 0x04
+
+/*
+ * DPTF temp thresholds. Any of the EC's temp sensors can have up to two
+ * independent thresholds attached to them. The current value of the ID
+ * register determines which sensor is affected by the THRESHOLD and COMMIT
+ * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme
+ * as the memory-mapped sensors. The COMMIT register applies those settings.
+ *
+ * The spec does not mandate any way to read back the threshold settings
+ * themselves, but when a threshold is crossed the AP needs a way to determine
+ * which sensor(s) are responsible. Each reading of the ID register clears and
+ * returns one sensor ID that has crossed one of its threshold (in either
+ * direction) since the last read. A value of 0xFF means "no new thresholds
+ * have tripped". Setting or enabling the thresholds for a sensor will clear
+ * the unread event count for that sensor.
+ */
+#define EC_ACPI_MEM_TEMP_ID 0x05
+#define EC_ACPI_MEM_TEMP_THRESHOLD 0x06
+#define EC_ACPI_MEM_TEMP_COMMIT 0x07
+/*
+ * Here are the bits for the COMMIT register:
+ * bit 0 selects the threshold index for the chosen sensor (0/1)
+ * bit 1 enables/disables the selected threshold (0 = off, 1 = on)
+ * Each write to the commit register affects one threshold.
+ */
+#define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK BIT(0)
+#define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK BIT(1)
+/*
+ * Example:
+ *
+ * Set the thresholds for sensor 2 to 50 C and 60 C:
+ * write 2 to [0x05] -- select temp sensor 2
+ * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET
+ * write 0x2 to [0x07] -- enable threshold 0 with this value
+ * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET
+ * write 0x3 to [0x07] -- enable threshold 1 with this value
+ *
+ * Disable the 60 C threshold, leaving the 50 C threshold unchanged:
+ * write 2 to [0x05] -- select temp sensor 2
+ * write 0x1 to [0x07] -- disable threshold 1
+ */
+
+/* DPTF battery charging current limit */
+#define EC_ACPI_MEM_CHARGING_LIMIT 0x08
+
+/* Charging limit is specified in 64 mA steps */
+#define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64
+/* Value to disable DPTF battery charging limit */
+#define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff
+
+/*
+ * Report device orientation
+ * Bits Definition
+ * 3:1 Device DPTF Profile Number (DDPN)
+ * 0 = Reserved for backward compatibility (indicates no valid
+ * profile number. Host should fall back to using TBMD).
+ * 1..7 = DPTF Profile number to indicate to host which table needs
+ * to be loaded.
+ * 0 Tablet Mode Device Indicator (TBMD)
+ */
+#define EC_ACPI_MEM_DEVICE_ORIENTATION 0x09
+#define EC_ACPI_MEM_TBMD_SHIFT 0
+#define EC_ACPI_MEM_TBMD_MASK 0x1
+#define EC_ACPI_MEM_DDPN_SHIFT 1
+#define EC_ACPI_MEM_DDPN_MASK 0x7
+
+/*
+ * Report device features. Uses the same format as the host command, except:
+ *
+ * bit 0 (EC_FEATURE_LIMITED) changes meaning from "EC code has a limited set
+ * of features", which is of limited interest when the system is already
+ * interpreting ACPI bytecode, to "EC_FEATURES[0-7] is not supported". Since
+ * these are supported, it defaults to 0.
+ * This allows detecting the presence of this field since older versions of
+ * the EC codebase would simply return 0xff to that unknown address. Check
+ * FEATURES0 != 0xff (or FEATURES0[0] == 0) to make sure that the other bits
+ * are valid.
+ */
+#define EC_ACPI_MEM_DEVICE_FEATURES0 0x0a
+#define EC_ACPI_MEM_DEVICE_FEATURES1 0x0b
+#define EC_ACPI_MEM_DEVICE_FEATURES2 0x0c
+#define EC_ACPI_MEM_DEVICE_FEATURES3 0x0d
+#define EC_ACPI_MEM_DEVICE_FEATURES4 0x0e
+#define EC_ACPI_MEM_DEVICE_FEATURES5 0x0f
+#define EC_ACPI_MEM_DEVICE_FEATURES6 0x10
+#define EC_ACPI_MEM_DEVICE_FEATURES7 0x11
+
+#define EC_ACPI_MEM_BATTERY_INDEX 0x12
+
+/*
+ * USB Port Power. Each bit indicates whether the corresponding USB ports' power
+ * is enabled (1) or disabled (0).
+ * bit 0 USB port ID 0
+ * ...
+ * bit 7 USB port ID 7
+ */
+#define EC_ACPI_MEM_USB_PORT_POWER 0x13
+
+/*
+ * ACPI addresses 0x20 - 0xff map to EC_MEMMAP offset 0x00 - 0xdf. This data
+ * is read-only from the AP. Added in EC_ACPI_MEM_VERSION 2.
+ */
+#define EC_ACPI_MEM_MAPPED_BEGIN 0x20
+#define EC_ACPI_MEM_MAPPED_SIZE 0xe0
+
+/* Current version of ACPI memory address space */
+#define EC_ACPI_MEM_VERSION_CURRENT 2
+
+
/*
* This header file is used in coreboot both in C and ACPI code. The ACPI code
* is pre-processed to handle constants but the ASL compiler is unable to
* handle actual C code so keep it separate.
*/
-#ifndef __ACPI__
+
/*
- * Define __packed if someone hasn't beat us to it. Linux kernel style
- * checking prefers __packed over __attribute__((packed)).
+ * Attributes for EC request and response packets. Just defining __packed
+ * results in inefficient assembly code on ARM, if the structure is actually
+ * 32-bit aligned, as it should be for all buffers.
+ *
+ * Be very careful when adding these to existing structures. They will round
+ * up the structure size to the specified boundary.
+ *
+ * Also be very careful to make that if a structure is included in some other
+ * parent structure that the alignment will still be true given the packing of
+ * the parent structure. This is particularly important if the sub-structure
+ * will be passed as a pointer to another function, since that function will
+ * not know about the misaligment caused by the parent structure's packing.
+ *
+ * Also be very careful using __packed - particularly when nesting non-packed
+ * structures inside packed ones. In fact, DO NOT use __packed directly;
+ * always use one of these attributes.
+ *
+ * Once everything is annotated properly, the following search strings should
+ * not return ANY matches in this file other than right here:
+ *
+ * "__packed" - generates inefficient code; all sub-structs must also be packed
+ *
+ * "struct [^_]" - all structs should be annotated, except for structs that are
+ * members of other structs/unions (and their original declarations should be
+ * annotated).
*/
-#ifndef __packed
-#define __packed __attribute__((packed))
-#endif
+
+/*
+ * Packed structures make no assumption about alignment, so they do inefficient
+ * byte-wise reads.
+ */
+#define __ec_align1 __packed
+#define __ec_align2 __packed
+#define __ec_align4 __packed
+#define __ec_align_size1 __packed
+#define __ec_align_offset1 __packed
+#define __ec_align_offset2 __packed
+#define __ec_todo_packed __packed
+#define __ec_todo_unpacked
+
/* LPC command status byte masks */
/* EC has written a byte in the data register and host hasn't read it yet */
@@ -206,7 +439,7 @@
#define EC_LPC_STATUS_PROCESSING 0x04
/* Last write to EC was a command, not data */
#define EC_LPC_STATUS_LAST_CMD 0x08
-/* EC is in burst mode. Unsupported by Chrome EC, so this bit is never set */
+/* EC is in burst mode */
#define EC_LPC_STATUS_BURST_MODE 0x10
/* SCI event is pending (requesting SCI query) */
#define EC_LPC_STATUS_SCI_PENDING 0x20
@@ -222,7 +455,10 @@
#define EC_LPC_STATUS_BUSY_MASK \
(EC_LPC_STATUS_FROM_HOST | EC_LPC_STATUS_PROCESSING)
-/* Host command response codes */
+/*
+ * Host command response codes (16-bit). Note that response codes should be
+ * stored in a uint16_t rather than directly in a value of this type.
+ */
enum ec_status {
EC_RES_SUCCESS = 0,
EC_RES_INVALID_COMMAND = 1,
@@ -238,7 +474,13 @@ enum ec_status {
EC_RES_OVERFLOW = 11, /* Table / data overflow */
EC_RES_INVALID_HEADER = 12, /* Header contains invalid data */
EC_RES_REQUEST_TRUNCATED = 13, /* Didn't get the entire request */
- EC_RES_RESPONSE_TOO_BIG = 14 /* Response was too big to handle */
+ EC_RES_RESPONSE_TOO_BIG = 14, /* Response was too big to handle */
+ EC_RES_BUS_ERROR = 15, /* Communications bus error */
+ EC_RES_BUSY = 16, /* Up but too busy. Should retry */
+ EC_RES_INVALID_HEADER_VERSION = 17, /* Header version invalid */
+ EC_RES_INVALID_HEADER_CRC = 18, /* Header CRC invalid */
+ EC_RES_INVALID_DATA_CRC = 19, /* Data CRC invalid */
+ EC_RES_DUP_UNAVAILABLE = 20, /* Can't resend response */
};
/*
@@ -258,7 +500,8 @@ enum host_event_code {
EC_HOST_EVENT_BATTERY_CRITICAL = 7,
EC_HOST_EVENT_BATTERY = 8,
EC_HOST_EVENT_THERMAL_THRESHOLD = 9,
- EC_HOST_EVENT_THERMAL_OVERLOAD = 10,
+ /* Event generated by a device attached to the EC */
+ EC_HOST_EVENT_DEVICE = 10,
EC_HOST_EVENT_THERMAL = 11,
EC_HOST_EVENT_USB_CHARGER = 12,
EC_HOST_EVENT_KEY_PRESSED = 13,
@@ -285,14 +528,33 @@ enum host_event_code {
EC_HOST_EVENT_HANG_DETECT = 20,
/* Hang detect logic detected a hang and warm rebooted the AP */
EC_HOST_EVENT_HANG_REBOOT = 21,
+
/* PD MCU triggering host event */
EC_HOST_EVENT_PD_MCU = 22,
+ /* Battery Status flags have changed */
+ EC_HOST_EVENT_BATTERY_STATUS = 23,
+
+ /* EC encountered a panic, triggering a reset */
+ EC_HOST_EVENT_PANIC = 24,
+
+ /* Keyboard fastboot combo has been pressed */
+ EC_HOST_EVENT_KEYBOARD_FASTBOOT = 25,
+
+ /* EC RTC event occurred */
+ EC_HOST_EVENT_RTC = 26,
+
+ /* Emulate MKBP event */
+ EC_HOST_EVENT_MKBP = 27,
+
/* EC desires to change state of host-controlled USB mux */
EC_HOST_EVENT_USB_MUX = 28,
- /* EC RTC event occurred */
- EC_HOST_EVENT_RTC = 26,
+ /* TABLET/LAPTOP mode or detachable base attach/detach event */
+ EC_HOST_EVENT_MODE_CHANGE = 29,
+
+ /* Keyboard recovery combo with hardware reinitialization */
+ EC_HOST_EVENT_KEYBOARD_RECOVERY_HW_REINIT = 30,
/*
* The high bit of the event mask is not used as a host event code. If
@@ -304,7 +566,7 @@ enum host_event_code {
EC_HOST_EVENT_INVALID = 32
};
/* Host event mask */
-#define EC_HOST_EVENT_MASK(event_code) (1UL << ((event_code) - 1))
+#define EC_HOST_EVENT_MASK(event_code) BIT_ULL((event_code) - 1)
/**
* struct ec_lpc_host_args - Arguments at EC_LPC_ADDR_HOST_ARGS
@@ -319,7 +581,7 @@ struct ec_lpc_host_args {
uint8_t command_version;
uint8_t data_size;
uint8_t checksum;
-} __packed;
+} __ec_align4;
/* Flags for ec_lpc_host_args.flags */
/*
@@ -329,7 +591,7 @@ struct ec_lpc_host_args {
* If EC gets a command and this flag is not set, this is an old-style command.
* Command version is 0 and params from host are at EC_LPC_ADDR_OLD_PARAM with
* unknown length. EC must respond with an old-style response (that is,
- * withouth setting EC_HOST_ARGS_FLAG_TO_HOST).
+ * without setting EC_HOST_ARGS_FLAG_TO_HOST).
*/
#define EC_HOST_ARGS_FLAG_FROM_HOST 0x01
/*
@@ -490,7 +752,7 @@ struct ec_host_request {
uint8_t command_version;
uint8_t reserved;
uint16_t data_len;
-} __packed;
+} __ec_align4;
#define EC_HOST_RESPONSE_VERSION 3
@@ -509,18 +771,151 @@ struct ec_host_response {
uint16_t result;
uint16_t data_len;
uint16_t reserved;
-} __packed;
+} __ec_align4;
+
+/*****************************************************************************/
+
+/*
+ * Host command protocol V4.
+ *
+ * Packets always start with a request or response header. They are followed
+ * by data_len bytes of data. If the data_crc_present flag is set, the data
+ * bytes are followed by a CRC-8 of that data, using using x^8 + x^2 + x + 1
+ * polynomial.
+ *
+ * Host algorithm when sending a request q:
+ *
+ * 101) tries_left=(some value, e.g. 3);
+ * 102) q.seq_num++
+ * 103) q.seq_dup=0
+ * 104) Calculate q.header_crc.
+ * 105) Send request q to EC.
+ * 106) Wait for response r. Go to 201 if received or 301 if timeout.
+ *
+ * 201) If r.struct_version != 4, go to 301.
+ * 202) If r.header_crc mismatches calculated CRC for r header, go to 301.
+ * 203) If r.data_crc_present and r.data_crc mismatches, go to 301.
+ * 204) If r.seq_num != q.seq_num, go to 301.
+ * 205) If r.seq_dup == q.seq_dup, return success.
+ * 207) If r.seq_dup == 1, go to 301.
+ * 208) Return error.
+ *
+ * 301) If --tries_left <= 0, return error.
+ * 302) If q.seq_dup == 1, go to 105.
+ * 303) q.seq_dup = 1
+ * 304) Go to 104.
+ *
+ * EC algorithm when receiving a request q.
+ * EC has response buffer r, error buffer e.
+ *
+ * 101) If q.struct_version != 4, set e.result = EC_RES_INVALID_HEADER_VERSION
+ * and go to 301
+ * 102) If q.header_crc mismatches calculated CRC, set e.result =
+ * EC_RES_INVALID_HEADER_CRC and go to 301
+ * 103) If q.data_crc_present, calculate data CRC. If that mismatches the CRC
+ * byte at the end of the packet, set e.result = EC_RES_INVALID_DATA_CRC
+ * and go to 301.
+ * 104) If q.seq_dup == 0, go to 201.
+ * 105) If q.seq_num != r.seq_num, go to 201.
+ * 106) If q.seq_dup == r.seq_dup, go to 205, else go to 203.
+ *
+ * 201) Process request q into response r.
+ * 202) r.seq_num = q.seq_num
+ * 203) r.seq_dup = q.seq_dup
+ * 204) Calculate r.header_crc
+ * 205) If r.data_len > 0 and data is no longer available, set e.result =
+ * EC_RES_DUP_UNAVAILABLE and go to 301.
+ * 206) Send response r.
+ *
+ * 301) e.seq_num = q.seq_num
+ * 302) e.seq_dup = q.seq_dup
+ * 303) Calculate e.header_crc.
+ * 304) Send error response e.
+ */
+
+/* Version 4 request from host */
+struct ec_host_request4 {
+ /*
+ * bits 0-3: struct_version: Structure version (=4)
+ * bit 4: is_response: Is response (=0)
+ * bits 5-6: seq_num: Sequence number
+ * bit 7: seq_dup: Sequence duplicate flag
+ */
+ uint8_t fields0;
+
+ /*
+ * bits 0-4: command_version: Command version
+ * bits 5-6: Reserved (set 0, ignore on read)
+ * bit 7: data_crc_present: Is data CRC present after data
+ */
+ uint8_t fields1;
+
+ /* Command code (EC_CMD_*) */
+ uint16_t command;
+
+ /* Length of data which follows this header (not including data CRC) */
+ uint16_t data_len;
+
+ /* Reserved (set 0, ignore on read) */
+ uint8_t reserved;
+
+ /* CRC-8 of above fields, using x^8 + x^2 + x + 1 polynomial */
+ uint8_t header_crc;
+} __ec_align4;
+
+/* Version 4 response from EC */
+struct ec_host_response4 {
+ /*
+ * bits 0-3: struct_version: Structure version (=4)
+ * bit 4: is_response: Is response (=1)
+ * bits 5-6: seq_num: Sequence number
+ * bit 7: seq_dup: Sequence duplicate flag
+ */
+ uint8_t fields0;
+
+ /*
+ * bits 0-6: Reserved (set 0, ignore on read)
+ * bit 7: data_crc_present: Is data CRC present after data
+ */
+ uint8_t fields1;
+
+ /* Result code (EC_RES_*) */
+ uint16_t result;
+
+ /* Length of data which follows this header (not including data CRC) */
+ uint16_t data_len;
+
+ /* Reserved (set 0, ignore on read) */
+ uint8_t reserved;
+
+ /* CRC-8 of above fields, using x^8 + x^2 + x + 1 polynomial */
+ uint8_t header_crc;
+} __ec_align4;
+
+/* Fields in fields0 byte */
+#define EC_PACKET4_0_STRUCT_VERSION_MASK 0x0f
+#define EC_PACKET4_0_IS_RESPONSE_MASK 0x10
+#define EC_PACKET4_0_SEQ_NUM_SHIFT 5
+#define EC_PACKET4_0_SEQ_NUM_MASK 0x60
+#define EC_PACKET4_0_SEQ_DUP_MASK 0x80
+
+/* Fields in fields1 byte */
+#define EC_PACKET4_1_COMMAND_VERSION_MASK 0x1f /* (request only) */
+#define EC_PACKET4_1_DATA_CRC_PRESENT_MASK 0x80
/*****************************************************************************/
/*
* Notes on commands:
*
* Each command is an 16-bit command value. Commands which take params or
- * return response data specify structs for that data. If no struct is
+ * return response data specify structures for that data. If no structure is
* specified, the command does not input or output data, respectively.
* Parameter/response length is implicit in the structs. Some underlying
* communication protocols (I2C, SPI) may add length or checksum headers, but
* those are implementation-dependent and not defined here.
+ *
+ * All commands MUST be #defined to be 4-digit UPPER CASE hex values
+ * (e.g., 0x00AB, not 0xab) for CONFIG_HOSTCMD_SECTION_SORTED to work.
*/
/*****************************************************************************/
@@ -530,7 +925,7 @@ struct ec_host_response {
* Get protocol version, used to deal with non-backward compatible protocol
* changes.
*/
-#define EC_CMD_PROTO_VERSION 0x00
+#define EC_CMD_PROTO_VERSION 0x0000
/**
* struct ec_response_proto_version - Response to the proto version command.
@@ -538,13 +933,13 @@ struct ec_host_response {
*/
struct ec_response_proto_version {
uint32_t version;
-} __packed;
+} __ec_align4;
/*
* Hello. This is a simple command to test the EC is responsive to
* commands.
*/
-#define EC_CMD_HELLO 0x01
+#define EC_CMD_HELLO 0x0001
/**
* struct ec_params_hello - Parameters to the hello command.
@@ -552,7 +947,7 @@ struct ec_response_proto_version {
*/
struct ec_params_hello {
uint32_t in_data;
-} __packed;
+} __ec_align4;
/**
* struct ec_response_hello - Response to the hello command.
@@ -560,10 +955,10 @@ struct ec_params_hello {
*/
struct ec_response_hello {
uint32_t out_data;
-} __packed;
+} __ec_align4;
/* Get version number */
-#define EC_CMD_GET_VERSION 0x02
+#define EC_CMD_GET_VERSION 0x0002
enum ec_current_image {
EC_IMAGE_UNKNOWN = 0,
@@ -583,10 +978,10 @@ struct ec_response_get_version {
char version_string_rw[32];
char reserved[32];
uint32_t current_image;
-} __packed;
+} __ec_align4;
/* Read test */
-#define EC_CMD_READ_TEST 0x03
+#define EC_CMD_READ_TEST 0x0003
/**
* struct ec_params_read_test - Parameters for the read test command.
@@ -596,7 +991,7 @@ struct ec_response_get_version {
struct ec_params_read_test {
uint32_t offset;
uint32_t size;
-} __packed;
+} __ec_align4;
/**
* struct ec_response_read_test - Response to the read test command.
@@ -604,17 +999,17 @@ struct ec_params_read_test {
*/
struct ec_response_read_test {
uint32_t data[32];
-} __packed;
+} __ec_align4;
/*
* Get build information
*
* Response is null-terminated string.
*/
-#define EC_CMD_GET_BUILD_INFO 0x04
+#define EC_CMD_GET_BUILD_INFO 0x0004
/* Get chip info */
-#define EC_CMD_GET_CHIP_INFO 0x05
+#define EC_CMD_GET_CHIP_INFO 0x0005
/**
* struct ec_response_get_chip_info - Response to the get chip info command.
@@ -626,10 +1021,10 @@ struct ec_response_get_chip_info {
char vendor[32];
char name[32];
char revision[32];
-} __packed;
+} __ec_align4;
/* Get board HW version */
-#define EC_CMD_GET_BOARD_VERSION 0x06
+#define EC_CMD_GET_BOARD_VERSION 0x0006
/**
* struct ec_response_board_version - Response to the board version command.
@@ -637,7 +1032,7 @@ struct ec_response_get_chip_info {
*/
struct ec_response_board_version {
uint16_t board_version;
-} __packed;
+} __ec_align2;
/*
* Read memory-mapped data.
@@ -647,7 +1042,7 @@ struct ec_response_board_version {
*
* Response is params.size bytes of data.
*/
-#define EC_CMD_READ_MEMMAP 0x07
+#define EC_CMD_READ_MEMMAP 0x0007
/**
* struct ec_params_read_memmap - Parameters for the read memory map command.
@@ -657,10 +1052,10 @@ struct ec_response_board_version {
struct ec_params_read_memmap {
uint8_t offset;
uint8_t size;
-} __packed;
+} __ec_align1;
/* Read versions supported for a command */
-#define EC_CMD_GET_CMD_VERSIONS 0x08
+#define EC_CMD_GET_CMD_VERSIONS 0x0008
/**
* struct ec_params_get_cmd_versions - Parameters for the get command versions.
@@ -668,7 +1063,7 @@ struct ec_params_read_memmap {
*/
struct ec_params_get_cmd_versions {
uint8_t cmd;
-} __packed;
+} __ec_align1;
/**
* struct ec_params_get_cmd_versions_v1 - Parameters for the get command
@@ -677,7 +1072,7 @@ struct ec_params_get_cmd_versions {
*/
struct ec_params_get_cmd_versions_v1 {
uint16_t cmd;
-} __packed;
+} __ec_align2;
/**
* struct ec_response_get_cmd_version - Response to the get command versions.
@@ -686,20 +1081,20 @@ struct ec_params_get_cmd_versions_v1 {
*/
struct ec_response_get_cmd_versions {
uint32_t version_mask;
-} __packed;
+} __ec_align4;
/*
- * Check EC communcations status (busy). This is needed on i2c/spi but not
+ * Check EC communications status (busy). This is needed on i2c/spi but not
* on lpc since it has its own out-of-band busy indicator.
*
* lpc must read the status from the command register. Attempting this on
* lpc will overwrite the args/parameter space and corrupt its data.
*/
-#define EC_CMD_GET_COMMS_STATUS 0x09
+#define EC_CMD_GET_COMMS_STATUS 0x0009
/* Avoid using ec_status which is for return values */
enum ec_comms_status {
- EC_COMMS_STATUS_PROCESSING = 1 << 0, /* Processing cmd */
+ EC_COMMS_STATUS_PROCESSING = BIT(0), /* Processing cmd */
};
/**
@@ -709,29 +1104,29 @@ enum ec_comms_status {
*/
struct ec_response_get_comms_status {
uint32_t flags; /* Mask of enum ec_comms_status */
-} __packed;
+} __ec_align4;
/* Fake a variety of responses, purely for testing purposes. */
-#define EC_CMD_TEST_PROTOCOL 0x0a
+#define EC_CMD_TEST_PROTOCOL 0x000A
/* Tell the EC what to send back to us. */
struct ec_params_test_protocol {
uint32_t ec_result;
uint32_t ret_len;
uint8_t buf[32];
-} __packed;
+} __ec_align4;
/* Here it comes... */
struct ec_response_test_protocol {
uint8_t buf[32];
-} __packed;
+} __ec_align4;
-/* Get prococol information */
-#define EC_CMD_GET_PROTOCOL_INFO 0x0b
+/* Get protocol information */
+#define EC_CMD_GET_PROTOCOL_INFO 0x000B
/* Flags for ec_response_get_protocol_info.flags */
/* EC_RES_IN_PROGRESS may be returned if a command is slow */
-#define EC_PROTOCOL_INFO_IN_PROGRESS_SUPPORTED (1 << 0)
+#define EC_PROTOCOL_INFO_IN_PROGRESS_SUPPORTED BIT(0)
/**
* struct ec_response_get_protocol_info - Response to the get protocol info.
@@ -747,7 +1142,7 @@ struct ec_response_get_protocol_info {
uint16_t max_request_packet_size;
uint16_t max_response_packet_size;
uint32_t flags;
-} __packed;
+} __ec_align4;
/*****************************************************************************/
@@ -765,19 +1160,19 @@ struct ec_response_get_protocol_info {
struct ec_params_get_set_value {
uint32_t flags;
uint32_t value;
-} __packed;
+} __ec_align4;
struct ec_response_get_set_value {
uint32_t flags;
uint32_t value;
-} __packed;
+} __ec_align4;
-/* More than one command can use these structs to get/set paramters. */
-#define EC_CMD_GSV_PAUSE_IN_S5 0x0c
+/* More than one command can use these structs to get/set parameters. */
+#define EC_CMD_GSV_PAUSE_IN_S5 0x000C
/*****************************************************************************/
/* List the features supported by the firmware */
-#define EC_CMD_GET_FEATURES 0x0d
+#define EC_CMD_GET_FEATURES 0x000D
/* Supported features */
enum ec_feature_code {
@@ -884,24 +1279,36 @@ enum ec_feature_code {
EC_FEATURE_REFINED_TABLET_MODE_HYSTERESIS = 37,
/* EC supports audio codec. */
EC_FEATURE_AUDIO_CODEC = 38,
- /* EC Supports SCP. */
+ /* The MCU is a System Companion Processor (SCP). */
EC_FEATURE_SCP = 39,
/* The MCU is an Integrated Sensor Hub */
EC_FEATURE_ISH = 40,
};
-#define EC_FEATURE_MASK_0(event_code) (1UL << (event_code % 32))
-#define EC_FEATURE_MASK_1(event_code) (1UL << (event_code - 32))
+#define EC_FEATURE_MASK_0(event_code) BIT(event_code % 32)
+#define EC_FEATURE_MASK_1(event_code) BIT(event_code - 32)
struct ec_response_get_features {
uint32_t flags[2];
-} __packed;
+} __ec_align4;
+
+/*****************************************************************************/
+/* Get the board's SKU ID from EC */
+#define EC_CMD_GET_SKU_ID 0x000E
+
+/* Set SKU ID from AP */
+#define EC_CMD_SET_SKU_ID 0x000F
+
+struct ec_sku_id_info {
+ uint32_t sku_id;
+} __ec_align4;
/*****************************************************************************/
/* Flash commands */
/* Get flash info */
-#define EC_CMD_FLASH_INFO 0x10
+#define EC_CMD_FLASH_INFO 0x0010
+#define EC_VER_FLASH_INFO 2
/**
* struct ec_response_flash_info - Response to the flash info command.
@@ -920,11 +1327,22 @@ struct ec_response_flash_info {
uint32_t write_block_size;
uint32_t erase_block_size;
uint32_t protect_block_size;
-} __packed;
+} __ec_align4;
-/* Flags for version 1+ flash info command */
-/* EC flash erases bits to 0 instead of 1 */
-#define EC_FLASH_INFO_ERASE_TO_0 (1 << 0)
+/*
+ * Flags for version 1+ flash info command
+ * EC flash erases bits to 0 instead of 1.
+ */
+#define EC_FLASH_INFO_ERASE_TO_0 BIT(0)
+
+/*
+ * Flash must be selected for read/write/erase operations to succeed. This may
+ * be necessary on a chip where write/erase can be corrupted by other board
+ * activity, or where the chip needs to enable some sort of programming voltage,
+ * or where the read/write/erase operations require cleanly suspending other
+ * chip functionality.
+ */
+#define EC_FLASH_INFO_SELECT_REQUIRED BIT(1)
/**
* struct ec_response_flash_info_1 - Response to the flash info v1 command.
@@ -946,7 +1364,14 @@ struct ec_response_flash_info {
* fields following.
*
* gcc anonymous structs don't seem to get along with the __packed directive;
- * if they did we'd define the version 0 struct as a sub-struct of this one.
+ * if they did we'd define the version 0 structure as a sub-structure of this
+ * one.
+ *
+ * Version 2 supports flash banks of different sizes:
+ * The caller specified the number of banks it has preallocated
+ * (num_banks_desc)
+ * The EC returns the number of banks describing the flash memory.
+ * It adds banks descriptions up to num_banks_desc.
*/
struct ec_response_flash_info_1 {
/* Version 0 fields; see above for description */
@@ -958,14 +1383,50 @@ struct ec_response_flash_info_1 {
/* Version 1 adds these fields: */
uint32_t write_ideal_size;
uint32_t flags;
-} __packed;
+} __ec_align4;
+
+struct ec_params_flash_info_2 {
+ /* Number of banks to describe */
+ uint16_t num_banks_desc;
+ /* Reserved; set 0; ignore on read */
+ uint8_t reserved[2];
+} __ec_align4;
+
+struct ec_flash_bank {
+ /* Number of sector is in this bank. */
+ uint16_t count;
+ /* Size in power of 2 of each sector (8 --> 256 bytes) */
+ uint8_t size_exp;
+ /* Minimal write size for the sectors in this bank */
+ uint8_t write_size_exp;
+ /* Erase size for the sectors in this bank */
+ uint8_t erase_size_exp;
+ /* Size for write protection, usually identical to erase size. */
+ uint8_t protect_size_exp;
+ /* Reserved; set 0; ignore on read */
+ uint8_t reserved[2];
+};
+
+struct ec_response_flash_info_2 {
+ /* Total flash in the EC. */
+ uint32_t flash_size;
+ /* Flags; see EC_FLASH_INFO_* */
+ uint32_t flags;
+ /* Maximum size to use to send data to write to the EC. */
+ uint32_t write_ideal_size;
+ /* Number of banks present in the EC. */
+ uint16_t num_banks_total;
+ /* Number of banks described in banks array. */
+ uint16_t num_banks_desc;
+ struct ec_flash_bank banks[0];
+} __ec_align4;
/*
* Read flash
*
* Response is params.size bytes of data.
*/
-#define EC_CMD_FLASH_READ 0x11
+#define EC_CMD_FLASH_READ 0x0011
/**
* struct ec_params_flash_read - Parameters for the flash read command.
@@ -975,10 +1436,10 @@ struct ec_response_flash_info_1 {
struct ec_params_flash_read {
uint32_t offset;
uint32_t size;
-} __packed;
+} __ec_align4;
/* Write flash */
-#define EC_CMD_FLASH_WRITE 0x12
+#define EC_CMD_FLASH_WRITE 0x0012
#define EC_VER_FLASH_WRITE 1
/* Version 0 of the flash command supported only 64 bytes of data */
@@ -993,20 +1454,57 @@ struct ec_params_flash_write {
uint32_t offset;
uint32_t size;
/* Followed by data to write */
-} __packed;
+} __ec_align4;
/* Erase flash */
-#define EC_CMD_FLASH_ERASE 0x13
+#define EC_CMD_FLASH_ERASE 0x0013
/**
- * struct ec_params_flash_erase - Parameters for the flash erase command.
+ * struct ec_params_flash_erase - Parameters for the flash erase command, v0.
* @offset: Byte offset to erase.
* @size: Size to erase in bytes.
*/
struct ec_params_flash_erase {
uint32_t offset;
uint32_t size;
-} __packed;
+} __ec_align4;
+
+/*
+ * v1 add async erase:
+ * subcommands can returns:
+ * EC_RES_SUCCESS : erased (see ERASE_SECTOR_ASYNC case below).
+ * EC_RES_INVALID_PARAM : offset/size are not aligned on a erase boundary.
+ * EC_RES_ERROR : other errors.
+ * EC_RES_BUSY : an existing erase operation is in progress.
+ * EC_RES_ACCESS_DENIED: Trying to erase running image.
+ *
+ * When ERASE_SECTOR_ASYNC returns EC_RES_SUCCESS, the operation is just
+ * properly queued. The user must call ERASE_GET_RESULT subcommand to get
+ * the proper result.
+ * When ERASE_GET_RESULT returns EC_RES_BUSY, the caller must wait and send
+ * ERASE_GET_RESULT again to get the result of ERASE_SECTOR_ASYNC.
+ * ERASE_GET_RESULT command may timeout on EC where flash access is not
+ * permitted while erasing. (For instance, STM32F4).
+ */
+enum ec_flash_erase_cmd {
+ FLASH_ERASE_SECTOR, /* Erase and wait for result */
+ FLASH_ERASE_SECTOR_ASYNC, /* Erase and return immediately. */
+ FLASH_ERASE_GET_RESULT, /* Ask for last erase result */
+};
+
+/**
+ * struct ec_params_flash_erase_v1 - Parameters for the flash erase command, v1.
+ * @cmd: One of ec_flash_erase_cmd.
+ * @reserved: Pad byte; currently always contains 0.
+ * @flag: No flags defined yet; set to 0.
+ * @params: Same as v0 parameters.
+ */
+struct ec_params_flash_erase_v1 {
+ uint8_t cmd;
+ uint8_t reserved;
+ uint16_t flag;
+ struct ec_params_flash_erase params;
+} __ec_align4;
/*
* Get/set flash protection.
@@ -1018,31 +1516,40 @@ struct ec_params_flash_erase {
*
* If mask=0, simply returns the current flags state.
*/
-#define EC_CMD_FLASH_PROTECT 0x15
+#define EC_CMD_FLASH_PROTECT 0x0015
#define EC_VER_FLASH_PROTECT 1 /* Command version 1 */
/* Flags for flash protection */
/* RO flash code protected when the EC boots */
-#define EC_FLASH_PROTECT_RO_AT_BOOT (1 << 0)
+#define EC_FLASH_PROTECT_RO_AT_BOOT BIT(0)
/*
* RO flash code protected now. If this bit is set, at-boot status cannot
* be changed.
*/
-#define EC_FLASH_PROTECT_RO_NOW (1 << 1)
+#define EC_FLASH_PROTECT_RO_NOW BIT(1)
/* Entire flash code protected now, until reboot. */
-#define EC_FLASH_PROTECT_ALL_NOW (1 << 2)
+#define EC_FLASH_PROTECT_ALL_NOW BIT(2)
/* Flash write protect GPIO is asserted now */
-#define EC_FLASH_PROTECT_GPIO_ASSERTED (1 << 3)
+#define EC_FLASH_PROTECT_GPIO_ASSERTED BIT(3)
/* Error - at least one bank of flash is stuck locked, and cannot be unlocked */
-#define EC_FLASH_PROTECT_ERROR_STUCK (1 << 4)
+#define EC_FLASH_PROTECT_ERROR_STUCK BIT(4)
/*
* Error - flash protection is in inconsistent state. At least one bank of
* flash which should be protected is not protected. Usually fixed by
* re-requesting the desired flags, or by a hard reset if that fails.
*/
-#define EC_FLASH_PROTECT_ERROR_INCONSISTENT (1 << 5)
-/* Entile flash code protected when the EC boots */
-#define EC_FLASH_PROTECT_ALL_AT_BOOT (1 << 6)
+#define EC_FLASH_PROTECT_ERROR_INCONSISTENT BIT(5)
+/* Entire flash code protected when the EC boots */
+#define EC_FLASH_PROTECT_ALL_AT_BOOT BIT(6)
+/* RW flash code protected when the EC boots */
+#define EC_FLASH_PROTECT_RW_AT_BOOT BIT(7)
+/* RW flash code protected now. */
+#define EC_FLASH_PROTECT_RW_NOW BIT(8)
+/* Rollback information flash region protected when the EC boots */
+#define EC_FLASH_PROTECT_ROLLBACK_AT_BOOT BIT(9)
+/* Rollback information flash region protected now */
+#define EC_FLASH_PROTECT_ROLLBACK_NOW BIT(10)
+
/**
* struct ec_params_flash_protect - Parameters for the flash protect command.
@@ -1052,7 +1559,7 @@ struct ec_params_flash_erase {
struct ec_params_flash_protect {
uint32_t mask;
uint32_t flags;
-} __packed;
+} __ec_align4;
/**
* struct ec_response_flash_protect - Response to the flash protect command.
@@ -1067,7 +1574,7 @@ struct ec_response_flash_protect {
uint32_t flags;
uint32_t valid_flags;
uint32_t writable_flags;
-} __packed;
+} __ec_align4;
/*
* Note: commands 0x14 - 0x19 version 0 were old commands to get/set flash
@@ -1075,22 +1582,37 @@ struct ec_response_flash_protect {
*/
/* Get the region offset/size */
-#define EC_CMD_FLASH_REGION_INFO 0x16
+#define EC_CMD_FLASH_REGION_INFO 0x0016
#define EC_VER_FLASH_REGION_INFO 1
enum ec_flash_region {
/* Region which holds read-only EC image */
EC_FLASH_REGION_RO = 0,
- /* Region which holds rewritable EC image */
- EC_FLASH_REGION_RW,
+ /*
+ * Region which holds active RW image. 'Active' is different from
+ * 'running'. Active means 'scheduled-to-run'. Since RO image always
+ * scheduled to run, active/non-active applies only to RW images (for
+ * the same reason 'update' applies only to RW images. It's a state of
+ * an image on a flash. Running image can be RO, RW_A, RW_B but active
+ * image can only be RW_A or RW_B. In recovery mode, an active RW image
+ * doesn't enter 'running' state but it's still active on a flash.
+ */
+ EC_FLASH_REGION_ACTIVE,
/*
* Region which should be write-protected in the factory (a superset of
* EC_FLASH_REGION_RO)
*/
EC_FLASH_REGION_WP_RO,
+ /* Region which holds updatable (non-active) RW image */
+ EC_FLASH_REGION_UPDATE,
/* Number of regions */
EC_FLASH_REGION_COUNT,
};
+/*
+ * 'RW' is vague if there are multiple RW images; we mean the active one,
+ * so the old constant is deprecated.
+ */
+#define EC_FLASH_REGION_RW EC_FLASH_REGION_ACTIVE
/**
* struct ec_params_flash_region_info - Parameters for the flash region info
@@ -1099,15 +1621,15 @@ enum ec_flash_region {
*/
struct ec_params_flash_region_info {
uint32_t region;
-} __packed;
+} __ec_align4;
struct ec_response_flash_region_info {
uint32_t offset;
uint32_t size;
-} __packed;
+} __ec_align4;
/* Read/write VbNvContext */
-#define EC_CMD_VBNV_CONTEXT 0x17
+#define EC_CMD_VBNV_CONTEXT 0x0017
#define EC_VER_VBNV_CONTEXT 1
#define EC_VBNV_BLOCK_SIZE 16
@@ -1119,52 +1641,99 @@ enum ec_vbnvcontext_op {
struct ec_params_vbnvcontext {
uint32_t op;
uint8_t block[EC_VBNV_BLOCK_SIZE];
-} __packed;
+} __ec_align4;
struct ec_response_vbnvcontext {
uint8_t block[EC_VBNV_BLOCK_SIZE];
-} __packed;
+} __ec_align4;
+
+
+/* Get SPI flash information */
+#define EC_CMD_FLASH_SPI_INFO 0x0018
+
+struct ec_response_flash_spi_info {
+ /* JEDEC info from command 0x9F (manufacturer, memory type, size) */
+ uint8_t jedec[3];
+
+ /* Pad byte; currently always contains 0 */
+ uint8_t reserved0;
+
+ /* Manufacturer / device ID from command 0x90 */
+ uint8_t mfr_dev_id[2];
+
+ /* Status registers from command 0x05 and 0x35 */
+ uint8_t sr1, sr2;
+} __ec_align1;
+
+
+/* Select flash during flash operations */
+#define EC_CMD_FLASH_SELECT 0x0019
+
+/**
+ * struct ec_params_flash_select - Parameters for the flash select command.
+ * @select: 1 to select flash, 0 to deselect flash
+ */
+struct ec_params_flash_select {
+ uint8_t select;
+} __ec_align4;
+
/*****************************************************************************/
/* PWM commands */
/* Get fan target RPM */
-#define EC_CMD_PWM_GET_FAN_TARGET_RPM 0x20
+#define EC_CMD_PWM_GET_FAN_TARGET_RPM 0x0020
struct ec_response_pwm_get_fan_rpm {
uint32_t rpm;
-} __packed;
+} __ec_align4;
/* Set target fan RPM */
-#define EC_CMD_PWM_SET_FAN_TARGET_RPM 0x21
+#define EC_CMD_PWM_SET_FAN_TARGET_RPM 0x0021
-struct ec_params_pwm_set_fan_target_rpm {
+/* Version 0 of input params */
+struct ec_params_pwm_set_fan_target_rpm_v0 {
uint32_t rpm;
-} __packed;
+} __ec_align4;
+
+/* Version 1 of input params */
+struct ec_params_pwm_set_fan_target_rpm_v1 {
+ uint32_t rpm;
+ uint8_t fan_idx;
+} __ec_align_size1;
/* Get keyboard backlight */
-#define EC_CMD_PWM_GET_KEYBOARD_BACKLIGHT 0x22
+/* OBSOLETE - Use EC_CMD_PWM_SET_DUTY */
+#define EC_CMD_PWM_GET_KEYBOARD_BACKLIGHT 0x0022
struct ec_response_pwm_get_keyboard_backlight {
uint8_t percent;
uint8_t enabled;
-} __packed;
+} __ec_align1;
/* Set keyboard backlight */
-#define EC_CMD_PWM_SET_KEYBOARD_BACKLIGHT 0x23
+/* OBSOLETE - Use EC_CMD_PWM_SET_DUTY */
+#define EC_CMD_PWM_SET_KEYBOARD_BACKLIGHT 0x0023
struct ec_params_pwm_set_keyboard_backlight {
uint8_t percent;
-} __packed;
+} __ec_align1;
/* Set target fan PWM duty cycle */
-#define EC_CMD_PWM_SET_FAN_DUTY 0x24
+#define EC_CMD_PWM_SET_FAN_DUTY 0x0024
-struct ec_params_pwm_set_fan_duty {
+/* Version 0 of input params */
+struct ec_params_pwm_set_fan_duty_v0 {
uint32_t percent;
-} __packed;
+} __ec_align4;
-#define EC_CMD_PWM_SET_DUTY 0x25
+/* Version 1 of input params */
+struct ec_params_pwm_set_fan_duty_v1 {
+ uint32_t percent;
+ uint8_t fan_idx;
+} __ec_align_size1;
+
+#define EC_CMD_PWM_SET_DUTY 0x0025
/* 16 bit duty cycle, 0xffff = 100% */
#define EC_PWM_MAX_DUTY 0xffff
@@ -1182,18 +1751,18 @@ struct ec_params_pwm_set_duty {
uint16_t duty; /* Duty cycle, EC_PWM_MAX_DUTY = 100% */
uint8_t pwm_type; /* ec_pwm_type */
uint8_t index; /* Type-specific index, or 0 if unique */
-} __packed;
+} __ec_align4;
-#define EC_CMD_PWM_GET_DUTY 0x26
+#define EC_CMD_PWM_GET_DUTY 0x0026
struct ec_params_pwm_get_duty {
uint8_t pwm_type; /* ec_pwm_type */
uint8_t index; /* Type-specific index, or 0 if unique */
-} __packed;
+} __ec_align1;
struct ec_response_pwm_get_duty {
uint16_t duty; /* Duty cycle, EC_PWM_MAX_DUTY = 100% */
-} __packed;
+} __ec_align2;
/*****************************************************************************/
/*
@@ -1202,11 +1771,11 @@ struct ec_response_pwm_get_duty {
* into a subcommand. We'll make separate structs for subcommands with
* different input args, so that we know how much to expect.
*/
-#define EC_CMD_LIGHTBAR_CMD 0x28
+#define EC_CMD_LIGHTBAR_CMD 0x0028
struct rgb_s {
uint8_t r, g, b;
-};
+} __ec_todo_unpacked;
#define LB_BATTERY_LEVELS 4
@@ -1246,7 +1815,7 @@ struct lightbar_params_v0 {
/* Color palette */
struct rgb_s color[8]; /* 0-3 are Google colors */
-} __packed;
+} __ec_todo_packed;
struct lightbar_params_v1 {
/* Timing */
@@ -1259,7 +1828,10 @@ struct lightbar_params_v1 {
int32_t s3_sleep_for;
int32_t s3_ramp_up;
int32_t s3_ramp_down;
+ int32_t s5_ramp_up;
+ int32_t s5_ramp_down;
int32_t tap_tick_delay;
+ int32_t tap_gate_delay;
int32_t tap_display_time;
/* Tap-for-battery params */
@@ -1287,84 +1859,182 @@ struct lightbar_params_v1 {
uint8_t s0_idx[2][LB_BATTERY_LEVELS]; /* AP is running */
uint8_t s3_idx[2][LB_BATTERY_LEVELS]; /* AP is sleeping */
+ /* s5: single color pulse on inhibited power-up */
+ uint8_t s5_idx;
+
/* Color palette */
struct rgb_s color[8]; /* 0-3 are Google colors */
-} __packed;
+} __ec_todo_packed;
-/* Lightbar program */
+/* Lightbar command params v2
+ * crbug.com/467716
+ *
+ * lightbar_parms_v1 was too big for i2c, therefore in v2, we split them up by
+ * logical groups to make it more manageable ( < 120 bytes).
+ *
+ * NOTE: Each of these groups must be less than 120 bytes.
+ */
+
+struct lightbar_params_v2_timing {
+ /* Timing */
+ int32_t google_ramp_up;
+ int32_t google_ramp_down;
+ int32_t s3s0_ramp_up;
+ int32_t s0_tick_delay[2]; /* AC=0/1 */
+ int32_t s0a_tick_delay[2]; /* AC=0/1 */
+ int32_t s0s3_ramp_down;
+ int32_t s3_sleep_for;
+ int32_t s3_ramp_up;
+ int32_t s3_ramp_down;
+ int32_t s5_ramp_up;
+ int32_t s5_ramp_down;
+ int32_t tap_tick_delay;
+ int32_t tap_gate_delay;
+ int32_t tap_display_time;
+} __ec_todo_packed;
+
+struct lightbar_params_v2_tap {
+ /* Tap-for-battery params */
+ uint8_t tap_pct_red;
+ uint8_t tap_pct_green;
+ uint8_t tap_seg_min_on;
+ uint8_t tap_seg_max_on;
+ uint8_t tap_seg_osc;
+ uint8_t tap_idx[3];
+} __ec_todo_packed;
+
+struct lightbar_params_v2_oscillation {
+ /* Oscillation */
+ uint8_t osc_min[2]; /* AC=0/1 */
+ uint8_t osc_max[2]; /* AC=0/1 */
+ uint8_t w_ofs[2]; /* AC=0/1 */
+} __ec_todo_packed;
+
+struct lightbar_params_v2_brightness {
+ /* Brightness limits based on the backlight and AC. */
+ uint8_t bright_bl_off_fixed[2]; /* AC=0/1 */
+ uint8_t bright_bl_on_min[2]; /* AC=0/1 */
+ uint8_t bright_bl_on_max[2]; /* AC=0/1 */
+} __ec_todo_packed;
+
+struct lightbar_params_v2_thresholds {
+ /* Battery level thresholds */
+ uint8_t battery_threshold[LB_BATTERY_LEVELS - 1];
+} __ec_todo_packed;
+
+struct lightbar_params_v2_colors {
+ /* Map [AC][battery_level] to color index */
+ uint8_t s0_idx[2][LB_BATTERY_LEVELS]; /* AP is running */
+ uint8_t s3_idx[2][LB_BATTERY_LEVELS]; /* AP is sleeping */
+
+ /* s5: single color pulse on inhibited power-up */
+ uint8_t s5_idx;
+
+ /* Color palette */
+ struct rgb_s color[8]; /* 0-3 are Google colors */
+} __ec_todo_packed;
+
+/* Lightbar program. */
#define EC_LB_PROG_LEN 192
struct lightbar_program {
uint8_t size;
uint8_t data[EC_LB_PROG_LEN];
-};
+} __ec_todo_unpacked;
struct ec_params_lightbar {
uint8_t cmd; /* Command (see enum lightbar_command) */
union {
- struct {
- /* no args */
- } dump, off, on, init, get_seq, get_params_v0, get_params_v1,
- version, get_brightness, get_demo, suspend, resume;
+ /*
+ * The following commands have no args:
+ *
+ * dump, off, on, init, get_seq, get_params_v0, get_params_v1,
+ * version, get_brightness, get_demo, suspend, resume,
+ * get_params_v2_timing, get_params_v2_tap, get_params_v2_osc,
+ * get_params_v2_bright, get_params_v2_thlds,
+ * get_params_v2_colors
+ *
+ * Don't use an empty struct, because C++ hates that.
+ */
- struct {
+ struct __ec_todo_unpacked {
uint8_t num;
} set_brightness, seq, demo;
- struct {
+ struct __ec_todo_unpacked {
uint8_t ctrl, reg, value;
} reg;
- struct {
+ struct __ec_todo_unpacked {
uint8_t led, red, green, blue;
} set_rgb;
- struct {
+ struct __ec_todo_unpacked {
uint8_t led;
} get_rgb;
- struct {
+ struct __ec_todo_unpacked {
uint8_t enable;
} manual_suspend_ctrl;
struct lightbar_params_v0 set_params_v0;
struct lightbar_params_v1 set_params_v1;
+
+ struct lightbar_params_v2_timing set_v2par_timing;
+ struct lightbar_params_v2_tap set_v2par_tap;
+ struct lightbar_params_v2_oscillation set_v2par_osc;
+ struct lightbar_params_v2_brightness set_v2par_bright;
+ struct lightbar_params_v2_thresholds set_v2par_thlds;
+ struct lightbar_params_v2_colors set_v2par_colors;
+
struct lightbar_program set_program;
};
-} __packed;
+} __ec_todo_packed;
struct ec_response_lightbar {
union {
- struct {
- struct {
+ struct __ec_todo_unpacked {
+ struct __ec_todo_unpacked {
uint8_t reg;
uint8_t ic0;
uint8_t ic1;
} vals[23];
} dump;
- struct {
+ struct __ec_todo_unpacked {
uint8_t num;
} get_seq, get_brightness, get_demo;
struct lightbar_params_v0 get_params_v0;
struct lightbar_params_v1 get_params_v1;
- struct {
+
+ struct lightbar_params_v2_timing get_params_v2_timing;
+ struct lightbar_params_v2_tap get_params_v2_tap;
+ struct lightbar_params_v2_oscillation get_params_v2_osc;
+ struct lightbar_params_v2_brightness get_params_v2_bright;
+ struct lightbar_params_v2_thresholds get_params_v2_thlds;
+ struct lightbar_params_v2_colors get_params_v2_colors;
+
+ struct __ec_todo_unpacked {
uint32_t num;
uint32_t flags;
} version;
- struct {
+ struct __ec_todo_unpacked {
uint8_t red, green, blue;
} get_rgb;
- struct {
- /* no return params */
- } off, on, init, set_brightness, seq, reg, set_rgb,
- demo, set_params_v0, set_params_v1,
- set_program, manual_suspend_ctrl, suspend, resume;
+ /*
+ * The following commands have no response:
+ *
+ * off, on, init, set_brightness, seq, reg, set_rgb, demo,
+ * set_params_v0, set_params_v1, set_program,
+ * manual_suspend_ctrl, suspend, resume, set_v2par_timing,
+ * set_v2par_tap, set_v2par_osc, set_v2par_bright,
+ * set_v2par_thlds, set_v2par_colors
+ */
};
-} __packed;
+} __ec_todo_packed;
/* Lightbar commands */
enum lightbar_command {
@@ -1390,13 +2060,25 @@ enum lightbar_command {
LIGHTBAR_CMD_MANUAL_SUSPEND_CTRL = 19,
LIGHTBAR_CMD_SUSPEND = 20,
LIGHTBAR_CMD_RESUME = 21,
+ LIGHTBAR_CMD_GET_PARAMS_V2_TIMING = 22,
+ LIGHTBAR_CMD_SET_PARAMS_V2_TIMING = 23,
+ LIGHTBAR_CMD_GET_PARAMS_V2_TAP = 24,
+ LIGHTBAR_CMD_SET_PARAMS_V2_TAP = 25,
+ LIGHTBAR_CMD_GET_PARAMS_V2_OSCILLATION = 26,
+ LIGHTBAR_CMD_SET_PARAMS_V2_OSCILLATION = 27,
+ LIGHTBAR_CMD_GET_PARAMS_V2_BRIGHTNESS = 28,
+ LIGHTBAR_CMD_SET_PARAMS_V2_BRIGHTNESS = 29,
+ LIGHTBAR_CMD_GET_PARAMS_V2_THRESHOLDS = 30,
+ LIGHTBAR_CMD_SET_PARAMS_V2_THRESHOLDS = 31,
+ LIGHTBAR_CMD_GET_PARAMS_V2_COLORS = 32,
+ LIGHTBAR_CMD_SET_PARAMS_V2_COLORS = 33,
LIGHTBAR_NUM_CMDS
};
/*****************************************************************************/
/* LED control commands */
-#define EC_CMD_LED_CONTROL 0x29
+#define EC_CMD_LED_CONTROL 0x0029
enum ec_led_id {
/* LED to indicate battery state of charge */
@@ -1408,13 +2090,21 @@ enum ec_led_id {
EC_LED_ID_POWER_LED,
/* LED on power adapter or its plug */
EC_LED_ID_ADAPTER_LED,
+ /* LED to indicate left side */
+ EC_LED_ID_LEFT_LED,
+ /* LED to indicate right side */
+ EC_LED_ID_RIGHT_LED,
+ /* LED to indicate recovery mode with HW_REINIT */
+ EC_LED_ID_RECOVERY_HW_REINIT_LED,
+ /* LED to indicate sysrq debug mode. */
+ EC_LED_ID_SYSRQ_DEBUG_LED,
EC_LED_ID_COUNT
};
/* LED control flags */
-#define EC_LED_FLAGS_QUERY (1 << 0) /* Query LED capability only */
-#define EC_LED_FLAGS_AUTO (1 << 1) /* Switch LED back to automatic control */
+#define EC_LED_FLAGS_QUERY BIT(0) /* Query LED capability only */
+#define EC_LED_FLAGS_AUTO BIT(1) /* Switch LED back to automatic control */
enum ec_led_colors {
EC_LED_COLOR_RED = 0,
@@ -1422,6 +2112,7 @@ enum ec_led_colors {
EC_LED_COLOR_BLUE,
EC_LED_COLOR_YELLOW,
EC_LED_COLOR_WHITE,
+ EC_LED_COLOR_AMBER,
EC_LED_COLOR_COUNT
};
@@ -1431,7 +2122,7 @@ struct ec_params_led_control {
uint8_t flags; /* Control flags */
uint8_t brightness[EC_LED_COLOR_COUNT];
-} __packed;
+} __ec_align1;
struct ec_response_led_control {
/*
@@ -1442,7 +2133,7 @@ struct ec_response_led_control {
* Other values means the LED is control by PWM.
*/
uint8_t brightness_range[EC_LED_COLOR_COUNT];
-} __packed;
+} __ec_align1;
/*****************************************************************************/
/* Verified boot commands */
@@ -1453,7 +2144,7 @@ struct ec_response_led_control {
*/
/* Verified boot hash command */
-#define EC_CMD_VBOOT_HASH 0x2A
+#define EC_CMD_VBOOT_HASH 0x002A
struct ec_params_vboot_hash {
uint8_t cmd; /* enum ec_vboot_hash_cmd */
@@ -1463,7 +2154,7 @@ struct ec_params_vboot_hash {
uint32_t offset; /* Offset in flash to hash */
uint32_t size; /* Number of bytes to hash */
uint8_t nonce_data[64]; /* Nonce data; ignored if nonce_size=0 */
-} __packed;
+} __ec_align4;
struct ec_response_vboot_hash {
uint8_t status; /* enum ec_vboot_hash_status */
@@ -1473,7 +2164,7 @@ struct ec_response_vboot_hash {
uint32_t offset; /* Offset in flash which was hashed */
uint32_t size; /* Number of bytes hashed */
uint8_t hash_digest[64]; /* Hash digest data */
-} __packed;
+} __ec_align4;
enum ec_vboot_hash_cmd {
EC_VBOOT_HASH_GET = 0, /* Get current hash status */
@@ -1497,15 +2188,22 @@ enum ec_vboot_hash_status {
* If one of these is specified, the EC will automatically update offset and
* size to the correct values for the specified image (RO or RW).
*/
-#define EC_VBOOT_HASH_OFFSET_RO 0xfffffffe
-#define EC_VBOOT_HASH_OFFSET_RW 0xfffffffd
+#define EC_VBOOT_HASH_OFFSET_RO 0xfffffffe
+#define EC_VBOOT_HASH_OFFSET_ACTIVE 0xfffffffd
+#define EC_VBOOT_HASH_OFFSET_UPDATE 0xfffffffc
+
+/*
+ * 'RW' is vague if there are multiple RW images; we mean the active one,
+ * so the old constant is deprecated.
+ */
+#define EC_VBOOT_HASH_OFFSET_RW EC_VBOOT_HASH_OFFSET_ACTIVE
/*****************************************************************************/
/*
* Motion sense commands. We'll make separate structs for sub-commands with
* different input args, so that we know how much to expect.
*/
-#define EC_CMD_MOTION_SENSE_CMD 0x2B
+#define EC_CMD_MOTION_SENSE_CMD 0x002B
/* Motion sense commands */
enum motionsense_command {
@@ -1524,7 +2222,13 @@ enum motionsense_command {
/*
* EC Rate command is a setter/getter command for the EC sampling rate
- * of all motion sensors in milliseconds.
+ * in milliseconds.
+ * It is per sensor, the EC run sample task at the minimum of all
+ * sensors EC_RATE.
+ * For sensors without hardware FIFO, EC_RATE should be equals to 1/ODR
+ * to collect all the sensor samples.
+ * For sensor with hardware FIFO, EC_RATE is used as the maximal delay
+ * to process of all motion sensors in milliseconds.
*/
MOTIONSENSE_CMD_EC_RATE = 2,
@@ -1555,32 +2259,76 @@ enum motionsense_command {
MOTIONSENSE_CMD_DATA = 6,
/*
- * Perform low level calibration.. On sensors that support it, ask to
- * do offset calibration.
+ * Return sensor fifo info.
+ */
+ MOTIONSENSE_CMD_FIFO_INFO = 7,
+
+ /*
+ * Insert a flush element in the fifo and return sensor fifo info.
+ * The host can use that element to synchronize its operation.
+ */
+ MOTIONSENSE_CMD_FIFO_FLUSH = 8,
+
+ /*
+ * Return a portion of the fifo.
+ */
+ MOTIONSENSE_CMD_FIFO_READ = 9,
+
+ /*
+ * Perform low level calibration.
+ * On sensors that support it, ask to do offset calibration.
*/
MOTIONSENSE_CMD_PERFORM_CALIB = 10,
/*
- * Sensor Offset command is a setter/getter command for the offset used
- * for calibration. The offsets can be calculated by the host, or via
+ * Sensor Offset command is a setter/getter command for the offset
+ * used for calibration.
+ * The offsets can be calculated by the host, or via
* PERFORM_CALIB command.
*/
MOTIONSENSE_CMD_SENSOR_OFFSET = 11,
- /* Number of motionsense sub-commands. */
- MOTIONSENSE_NUM_CMDS
-};
-
-enum motionsensor_id {
- EC_MOTION_SENSOR_ACCEL_BASE = 0,
- EC_MOTION_SENSOR_ACCEL_LID = 1,
- EC_MOTION_SENSOR_GYRO = 2,
+ /*
+ * List available activities for a MOTION sensor.
+ * Indicates if they are enabled or disabled.
+ */
+ MOTIONSENSE_CMD_LIST_ACTIVITIES = 12,
/*
- * Note, if more sensors are added and this count changes, the padding
- * in ec_response_motion_sense dump command must be modified.
+ * Activity management
+ * Enable/Disable activity recognition.
*/
- EC_MOTION_SENSOR_COUNT = 3
+ MOTIONSENSE_CMD_SET_ACTIVITY = 13,
+
+ /*
+ * Lid Angle
+ */
+ MOTIONSENSE_CMD_LID_ANGLE = 14,
+
+ /*
+ * Allow the FIFO to trigger interrupt via MKBP events.
+ * By default the FIFO does not send interrupt to process the FIFO
+ * until the AP is ready or it is coming from a wakeup sensor.
+ */
+ MOTIONSENSE_CMD_FIFO_INT_ENABLE = 15,
+
+ /*
+ * Spoof the readings of the sensors. The spoofed readings can be set
+ * to arbitrary values, or will lock to the last read actual values.
+ */
+ MOTIONSENSE_CMD_SPOOF = 16,
+
+ /* Set lid angle for tablet mode detection. */
+ MOTIONSENSE_CMD_TABLET_MODE_LID_ANGLE = 17,
+
+ /*
+ * Sensor Scale command is a setter/getter command for the calibration
+ * scale.
+ */
+ MOTIONSENSE_CMD_SENSOR_SCALE = 18,
+
+ /* Number of motionsense sub-commands. */
+ MOTIONSENSE_NUM_CMDS
};
/* List of motion sensor types. */
@@ -1592,6 +2340,7 @@ enum motionsensor_type {
MOTIONSENSE_TYPE_LIGHT = 4,
MOTIONSENSE_TYPE_ACTIVITY = 5,
MOTIONSENSE_TYPE_BARO = 6,
+ MOTIONSENSE_TYPE_SYNC = 7,
MOTIONSENSE_TYPE_MAX,
};
@@ -1599,19 +2348,116 @@ enum motionsensor_type {
enum motionsensor_location {
MOTIONSENSE_LOC_BASE = 0,
MOTIONSENSE_LOC_LID = 1,
+ MOTIONSENSE_LOC_CAMERA = 2,
MOTIONSENSE_LOC_MAX,
};
/* List of motion sensor chips. */
enum motionsensor_chip {
MOTIONSENSE_CHIP_KXCJ9 = 0,
+ MOTIONSENSE_CHIP_LSM6DS0 = 1,
+ MOTIONSENSE_CHIP_BMI160 = 2,
+ MOTIONSENSE_CHIP_SI1141 = 3,
+ MOTIONSENSE_CHIP_SI1142 = 4,
+ MOTIONSENSE_CHIP_SI1143 = 5,
+ MOTIONSENSE_CHIP_KX022 = 6,
+ MOTIONSENSE_CHIP_L3GD20H = 7,
+ MOTIONSENSE_CHIP_BMA255 = 8,
+ MOTIONSENSE_CHIP_BMP280 = 9,
+ MOTIONSENSE_CHIP_OPT3001 = 10,
+ MOTIONSENSE_CHIP_BH1730 = 11,
+ MOTIONSENSE_CHIP_GPIO = 12,
+ MOTIONSENSE_CHIP_LIS2DH = 13,
+ MOTIONSENSE_CHIP_LSM6DSM = 14,
+ MOTIONSENSE_CHIP_LIS2DE = 15,
+ MOTIONSENSE_CHIP_LIS2MDL = 16,
+ MOTIONSENSE_CHIP_LSM6DS3 = 17,
+ MOTIONSENSE_CHIP_LSM6DSO = 18,
+ MOTIONSENSE_CHIP_LNG2DM = 19,
+ MOTIONSENSE_CHIP_MAX,
};
+/* List of orientation positions */
+enum motionsensor_orientation {
+ MOTIONSENSE_ORIENTATION_LANDSCAPE = 0,
+ MOTIONSENSE_ORIENTATION_PORTRAIT = 1,
+ MOTIONSENSE_ORIENTATION_UPSIDE_DOWN_PORTRAIT = 2,
+ MOTIONSENSE_ORIENTATION_UPSIDE_DOWN_LANDSCAPE = 3,
+ MOTIONSENSE_ORIENTATION_UNKNOWN = 4,
+};
+
+struct ec_response_motion_sensor_data {
+ /* Flags for each sensor. */
+ uint8_t flags;
+ /* Sensor number the data comes from. */
+ uint8_t sensor_num;
+ /* Each sensor is up to 3-axis. */
+ union {
+ int16_t data[3];
+ struct __ec_todo_packed {
+ uint16_t reserved;
+ uint32_t timestamp;
+ };
+ struct __ec_todo_unpacked {
+ uint8_t activity; /* motionsensor_activity */
+ uint8_t state;
+ int16_t add_info[2];
+ };
+ };
+} __ec_todo_packed;
+
+/* Note: used in ec_response_get_next_data */
+struct ec_response_motion_sense_fifo_info {
+ /* Size of the fifo */
+ uint16_t size;
+ /* Amount of space used in the fifo */
+ uint16_t count;
+ /* Timestamp recorded in us.
+ * aka accurate timestamp when host event was triggered.
+ */
+ uint32_t timestamp;
+ /* Total amount of vector lost */
+ uint16_t total_lost;
+ /* Lost events since the last fifo_info, per sensors */
+ uint16_t lost[0];
+} __ec_todo_packed;
+
+struct ec_response_motion_sense_fifo_data {
+ uint32_t number_data;
+ struct ec_response_motion_sensor_data data[0];
+} __ec_todo_packed;
+
+/* List supported activity recognition */
+enum motionsensor_activity {
+ MOTIONSENSE_ACTIVITY_RESERVED = 0,
+ MOTIONSENSE_ACTIVITY_SIG_MOTION = 1,
+ MOTIONSENSE_ACTIVITY_DOUBLE_TAP = 2,
+ MOTIONSENSE_ACTIVITY_ORIENTATION = 3,
+};
+
+struct ec_motion_sense_activity {
+ uint8_t sensor_num;
+ uint8_t activity; /* one of enum motionsensor_activity */
+ uint8_t enable; /* 1: enable, 0: disable */
+ uint8_t reserved;
+ uint16_t parameters[3]; /* activity dependent parameters */
+} __ec_todo_unpacked;
+
/* Module flag masks used for the dump sub-command. */
-#define MOTIONSENSE_MODULE_FLAG_ACTIVE (1<<0)
+#define MOTIONSENSE_MODULE_FLAG_ACTIVE BIT(0)
/* Sensor flag masks used for the dump sub-command. */
-#define MOTIONSENSE_SENSOR_FLAG_PRESENT (1<<0)
+#define MOTIONSENSE_SENSOR_FLAG_PRESENT BIT(0)
+
+/*
+ * Flush entry for synchronization.
+ * data contains time stamp
+ */
+#define MOTIONSENSE_SENSOR_FLAG_FLUSH BIT(0)
+#define MOTIONSENSE_SENSOR_FLAG_TIMESTAMP BIT(1)
+#define MOTIONSENSE_SENSOR_FLAG_WAKEUP BIT(2)
+#define MOTIONSENSE_SENSOR_FLAG_TABLET_MODE BIT(3)
+#define MOTIONSENSE_SENSOR_FLAG_ODR BIT(4)
/*
* Send this value for the data element to only perform a read. If you
@@ -1622,48 +2468,79 @@ enum motionsensor_chip {
#define EC_MOTION_SENSE_INVALID_CALIB_TEMP 0x8000
+/* MOTIONSENSE_CMD_SENSOR_OFFSET subcommand flag */
/* Set Calibration information */
-#define MOTION_SENSE_SET_OFFSET 1
+#define MOTION_SENSE_SET_OFFSET BIT(0)
-struct ec_response_motion_sensor_data {
- /* Flags for each sensor. */
- uint8_t flags;
- /* Sensor number the data comes from */
- uint8_t sensor_num;
- /* Each sensor is up to 3-axis. */
- union {
- int16_t data[3];
- struct {
- uint16_t rsvd;
- uint32_t timestamp;
- } __packed;
- struct {
- uint8_t activity; /* motionsensor_activity */
- uint8_t state;
- int16_t add_info[2];
- };
- };
-} __packed;
+/* Default Scale value, factor 1. */
+#define MOTION_SENSE_DEFAULT_SCALE BIT(15)
+
+#define LID_ANGLE_UNRELIABLE 500
+
+enum motionsense_spoof_mode {
+ /* Disable spoof mode. */
+ MOTIONSENSE_SPOOF_MODE_DISABLE = 0,
+
+ /* Enable spoof mode, but use provided component values. */
+ MOTIONSENSE_SPOOF_MODE_CUSTOM,
+
+ /* Enable spoof mode, but use the current sensor values. */
+ MOTIONSENSE_SPOOF_MODE_LOCK_CURRENT,
+
+ /* Query the current spoof mode status for the sensor. */
+ MOTIONSENSE_SPOOF_MODE_QUERY,
+};
struct ec_params_motion_sense {
uint8_t cmd;
union {
/* Used for MOTIONSENSE_CMD_DUMP. */
- struct {
- /* no args */
+ struct __ec_todo_unpacked {
+ /*
+ * Maximal number of sensor the host is expecting.
+ * 0 means the host is only interested in the number
+ * of sensors controlled by the EC.
+ */
+ uint8_t max_sensor_count;
} dump;
/*
- * Used for MOTIONSENSE_CMD_EC_RATE and
- * MOTIONSENSE_CMD_KB_WAKE_ANGLE.
+ * Used for MOTIONSENSE_CMD_KB_WAKE_ANGLE.
*/
- struct {
- /* Data to set or EC_MOTION_SENSE_NO_VALUE to read. */
+ struct __ec_todo_unpacked {
+ /* Data to set or EC_MOTION_SENSE_NO_VALUE to read.
+ * kb_wake_angle: angle to wakup AP.
+ */
int16_t data;
- } ec_rate, kb_wake_angle;
+ } kb_wake_angle;
+
+ /*
+ * Used for MOTIONSENSE_CMD_INFO, MOTIONSENSE_CMD_DATA
+ * and MOTIONSENSE_CMD_PERFORM_CALIB.
+ */
+ struct __ec_todo_unpacked {
+ uint8_t sensor_num;
+ } info, info_3, data, fifo_flush, perform_calib,
+ list_activities;
+
+ /*
+ * Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR
+ * and MOTIONSENSE_CMD_SENSOR_RANGE.
+ */
+ struct __ec_todo_unpacked {
+ uint8_t sensor_num;
+
+ /* Rounding flag, true for round-up, false for down. */
+ uint8_t roundup;
+
+ uint16_t reserved;
+
+ /* Data to set or EC_MOTION_SENSE_NO_VALUE to read. */
+ int32_t data;
+ } ec_rate, sensor_odr, sensor_range;
/* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */
- struct {
+ struct __ec_todo_packed {
uint8_t sensor_num;
/*
@@ -1689,36 +2566,102 @@ struct ec_params_motion_sense {
* Compass: 1/16 uT
*/
int16_t offset[3];
- } __packed sensor_offset;
+ } sensor_offset;
- /* Used for MOTIONSENSE_CMD_INFO. */
- struct {
- uint8_t sensor_num;
- } info;
-
- /*
- * Used for MOTIONSENSE_CMD_SENSOR_ODR and
- * MOTIONSENSE_CMD_SENSOR_RANGE.
- */
- struct {
- /* Should be element of enum motionsensor_id. */
+ /* Used for MOTIONSENSE_CMD_SENSOR_SCALE */
+ struct __ec_todo_packed {
uint8_t sensor_num;
- /* Rounding flag, true for round-up, false for down. */
- uint8_t roundup;
+ /*
+ * bit 0: If set (MOTION_SENSE_SET_OFFSET), set
+ * the calibration information in the EC.
+ * If unset, just retrieve calibration information.
+ */
+ uint16_t flags;
- uint16_t reserved;
+ /*
+ * Temperature at calibration, in units of 0.01 C
+ * 0x8000: invalid / unknown.
+ * 0x0: 0C
+ * 0x7fff: +327.67C
+ */
+ int16_t temp;
- /* Data to set or EC_MOTION_SENSE_NO_VALUE to read. */
- int32_t data;
- } sensor_odr, sensor_range;
+ /*
+ * Scale for calibration:
+ * By default scale is 1, it is encoded on 16bits:
+ * 1 = BIT(15)
+ * ~2 = 0xFFFF
+ * ~0 = 0.
+ */
+ uint16_t scale[3];
+ } sensor_scale;
+
+
+ /* Used for MOTIONSENSE_CMD_FIFO_INFO */
+ /* (no params) */
+
+ /* Used for MOTIONSENSE_CMD_FIFO_READ */
+ struct __ec_todo_unpacked {
+ /*
+ * Number of expected vector to return.
+ * EC may return less or 0 if none available.
+ */
+ uint32_t max_data_vector;
+ } fifo_read;
+
+ struct ec_motion_sense_activity set_activity;
+
+ /* Used for MOTIONSENSE_CMD_LID_ANGLE */
+ /* (no params) */
+
+ /* Used for MOTIONSENSE_CMD_FIFO_INT_ENABLE */
+ struct __ec_todo_unpacked {
+ /*
+ * 1: enable, 0 disable fifo,
+ * EC_MOTION_SENSE_NO_VALUE return value.
+ */
+ int8_t enable;
+ } fifo_int_enable;
+
+ /* Used for MOTIONSENSE_CMD_SPOOF */
+ struct __ec_todo_packed {
+ uint8_t sensor_id;
+
+ /* See enum motionsense_spoof_mode. */
+ uint8_t spoof_enable;
+
+ /* Ignored, used for alignment. */
+ uint8_t reserved;
+
+ /* Individual component values to spoof. */
+ int16_t components[3];
+ } spoof;
+
+ /* Used for MOTIONSENSE_CMD_TABLET_MODE_LID_ANGLE. */
+ struct __ec_todo_unpacked {
+ /*
+ * Lid angle threshold for switching between tablet and
+ * clamshell mode.
+ */
+ int16_t lid_angle;
+
+ /*
+ * Hysteresis degree to prevent fluctuations between
+ * clamshell and tablet mode if lid angle keeps
+ * changing around the threshold. Lid motion driver will
+ * use lid_angle + hys_degree to trigger tablet mode and
+ * lid_angle - hys_degree to trigger clamshell mode.
+ */
+ int16_t hys_degree;
+ } tablet_mode_threshold;
};
-} __packed;
+} __ec_todo_packed;
struct ec_response_motion_sense {
union {
- /* Used for MOTIONSENSE_CMD_DUMP. */
- struct {
+ /* Used for MOTIONSENSE_CMD_DUMP */
+ struct __ec_todo_unpacked {
/* Flags representing the motion sensor module. */
uint8_t module_flags;
@@ -1733,7 +2676,7 @@ struct ec_response_motion_sense {
} dump;
/* Used for MOTIONSENSE_CMD_INFO. */
- struct {
+ struct __ec_todo_unpacked {
/* Should be element of enum motionsensor_type. */
uint8_t type;
@@ -1744,37 +2687,129 @@ struct ec_response_motion_sense {
uint8_t chip;
} info;
+ /* Used for MOTIONSENSE_CMD_INFO version 3 */
+ struct __ec_todo_unpacked {
+ /* Should be element of enum motionsensor_type. */
+ uint8_t type;
+
+ /* Should be element of enum motionsensor_location. */
+ uint8_t location;
+
+ /* Should be element of enum motionsensor_chip. */
+ uint8_t chip;
+
+ /* Minimum sensor sampling frequency */
+ uint32_t min_frequency;
+
+ /* Maximum sensor sampling frequency */
+ uint32_t max_frequency;
+
+ /* Max number of sensor events that could be in fifo */
+ uint32_t fifo_max_event_count;
+ } info_3;
+
/* Used for MOTIONSENSE_CMD_DATA */
struct ec_response_motion_sensor_data data;
/*
* Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR,
- * MOTIONSENSE_CMD_SENSOR_RANGE, and
- * MOTIONSENSE_CMD_KB_WAKE_ANGLE.
+ * MOTIONSENSE_CMD_SENSOR_RANGE,
+ * MOTIONSENSE_CMD_KB_WAKE_ANGLE,
+ * MOTIONSENSE_CMD_FIFO_INT_ENABLE and
+ * MOTIONSENSE_CMD_SPOOF.
*/
- struct {
+ struct __ec_todo_unpacked {
/* Current value of the parameter queried. */
int32_t ret;
- } ec_rate, sensor_odr, sensor_range, kb_wake_angle;
+ } ec_rate, sensor_odr, sensor_range, kb_wake_angle,
+ fifo_int_enable, spoof;
- /* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */
- struct {
+ /*
+ * Used for MOTIONSENSE_CMD_SENSOR_OFFSET,
+ * PERFORM_CALIB.
+ */
+ struct __ec_todo_unpacked {
int16_t temp;
int16_t offset[3];
} sensor_offset, perform_calib;
+
+ /* Used for MOTIONSENSE_CMD_SENSOR_SCALE */
+ struct __ec_todo_unpacked {
+ int16_t temp;
+ uint16_t scale[3];
+ } sensor_scale;
+
+ struct ec_response_motion_sense_fifo_info fifo_info, fifo_flush;
+
+ struct ec_response_motion_sense_fifo_data fifo_read;
+
+ struct __ec_todo_packed {
+ uint16_t reserved;
+ uint32_t enabled;
+ uint32_t disabled;
+ } list_activities;
+
+ /* No params for set activity */
+
+ /* Used for MOTIONSENSE_CMD_LID_ANGLE */
+ struct __ec_todo_unpacked {
+ /*
+ * Angle between 0 and 360 degree if available,
+ * LID_ANGLE_UNRELIABLE otherwise.
+ */
+ uint16_t value;
+ } lid_angle;
+
+ /* Used for MOTIONSENSE_CMD_TABLET_MODE_LID_ANGLE. */
+ struct __ec_todo_unpacked {
+ /*
+ * Lid angle threshold for switching between tablet and
+ * clamshell mode.
+ */
+ uint16_t lid_angle;
+
+ /* Hysteresis degree. */
+ uint16_t hys_degree;
+ } tablet_mode_threshold;
+
};
-} __packed;
+} __ec_todo_packed;
+
+/*****************************************************************************/
+/* Force lid open command */
+
+/* Make lid event always open */
+#define EC_CMD_FORCE_LID_OPEN 0x002C
+
+struct ec_params_force_lid_open {
+ uint8_t enabled;
+} __ec_align1;
+
+/*****************************************************************************/
+/* Configure the behavior of the power button */
+#define EC_CMD_CONFIG_POWER_BUTTON 0x002D
+
+enum ec_config_power_button_flags {
+ /* Enable/Disable power button pulses for x86 devices */
+ EC_POWER_BUTTON_ENABLE_PULSE = BIT(0),
+};
+
+struct ec_params_config_power_button {
+ /* See enum ec_config_power_button_flags */
+ uint8_t flags;
+} __ec_align1;
/*****************************************************************************/
/* USB charging control commands */
/* Set USB port charging mode */
-#define EC_CMD_USB_CHARGE_SET_MODE 0x30
+#define EC_CMD_USB_CHARGE_SET_MODE 0x0030
struct ec_params_usb_charge_set_mode {
uint8_t usb_port_id;
- uint8_t mode;
-} __packed;
+ uint8_t mode:7;
+ uint8_t inhibit_charge:1;
+} __ec_align1;
/*****************************************************************************/
/* Persistent storage for host */
@@ -1783,35 +2818,35 @@ struct ec_params_usb_charge_set_mode {
#define EC_PSTORE_SIZE_MAX 64
/* Get persistent storage info */
-#define EC_CMD_PSTORE_INFO 0x40
+#define EC_CMD_PSTORE_INFO 0x0040
struct ec_response_pstore_info {
/* Persistent storage size, in bytes */
uint32_t pstore_size;
/* Access size; read/write offset and size must be a multiple of this */
uint32_t access_size;
-} __packed;
+} __ec_align4;
/*
* Read persistent storage
*
* Response is params.size bytes of data.
*/
-#define EC_CMD_PSTORE_READ 0x41
+#define EC_CMD_PSTORE_READ 0x0041
struct ec_params_pstore_read {
uint32_t offset; /* Byte offset to read */
uint32_t size; /* Size to read in bytes */
-} __packed;
+} __ec_align4;
/* Write persistent storage */
-#define EC_CMD_PSTORE_WRITE 0x42
+#define EC_CMD_PSTORE_WRITE 0x0042
struct ec_params_pstore_write {
uint32_t offset; /* Byte offset to write */
uint32_t size; /* Size to write in bytes */
uint8_t data[EC_PSTORE_SIZE_MAX];
-} __packed;
+} __ec_align4;
/*****************************************************************************/
/* Real-time clock */
@@ -1819,21 +2854,21 @@ struct ec_params_pstore_write {
/* RTC params and response structures */
struct ec_params_rtc {
uint32_t time;
-} __packed;
+} __ec_align4;
struct ec_response_rtc {
uint32_t time;
-} __packed;
+} __ec_align4;
/* These use ec_response_rtc */
-#define EC_CMD_RTC_GET_VALUE 0x44
-#define EC_CMD_RTC_GET_ALARM 0x45
+#define EC_CMD_RTC_GET_VALUE 0x0044
+#define EC_CMD_RTC_GET_ALARM 0x0045
/* These all use ec_params_rtc */
-#define EC_CMD_RTC_SET_VALUE 0x46
-#define EC_CMD_RTC_SET_ALARM 0x47
+#define EC_CMD_RTC_SET_VALUE 0x0046
+#define EC_CMD_RTC_SET_ALARM 0x0047
-/* Pass as param to SET_ALARM to clear the current alarm */
+/* Pass as time param to SET_ALARM to clear the current alarm */
#define EC_RTC_ALARM_CLEAR 0
/*****************************************************************************/
@@ -1843,8 +2878,8 @@ struct ec_response_rtc {
#define EC_PORT80_SIZE_MAX 32
/* Get last port80 code from previous boot */
-#define EC_CMD_PORT80_LAST_BOOT 0x48
-#define EC_CMD_PORT80_READ 0x48
+#define EC_CMD_PORT80_LAST_BOOT 0x0048
+#define EC_CMD_PORT80_READ 0x0048
enum ec_port80_subcmd {
EC_PORT80_GET_INFO = 0,
@@ -1854,29 +2889,72 @@ enum ec_port80_subcmd {
struct ec_params_port80_read {
uint16_t subcmd;
union {
- struct {
+ struct __ec_todo_unpacked {
uint32_t offset;
uint32_t num_entries;
} read_buffer;
};
-} __packed;
+} __ec_todo_packed;
struct ec_response_port80_read {
union {
- struct {
+ struct __ec_todo_unpacked {
uint32_t writes;
uint32_t history_size;
uint32_t last_boot;
} get_info;
- struct {
+ struct __ec_todo_unpacked {
uint16_t codes[EC_PORT80_SIZE_MAX];
} data;
};
-} __packed;
+} __ec_todo_packed;
struct ec_response_port80_last_boot {
uint16_t code;
-} __packed;
+} __ec_align2;
+
+/*****************************************************************************/
+/* Temporary secure storage for host verified boot use */
+
+/* Number of bytes in a vstore slot */
+#define EC_VSTORE_SLOT_SIZE 64
+
+/* Maximum number of vstore slots */
+#define EC_VSTORE_SLOT_MAX 32
+
+/* Get persistent storage info */
+#define EC_CMD_VSTORE_INFO 0x0049
+struct ec_response_vstore_info {
+ /* Indicates which slots are locked */
+ uint32_t slot_locked;
+ /* Total number of slots available */
+ uint8_t slot_count;
+} __ec_align_size1;
+
+/*
+ * Read temporary secure storage
+ *
+ * Response is EC_VSTORE_SLOT_SIZE bytes of data.
+ */
+#define EC_CMD_VSTORE_READ 0x004A
+
+struct ec_params_vstore_read {
+ uint8_t slot; /* Slot to read from */
+} __ec_align1;
+
+struct ec_response_vstore_read {
+ uint8_t data[EC_VSTORE_SLOT_SIZE];
+} __ec_align1;
+
+/*
+ * Write temporary secure storage and lock it.
+ */
+#define EC_CMD_VSTORE_WRITE 0x004B
+
+struct ec_params_vstore_write {
+ uint8_t slot; /* Slot to write to */
+ uint8_t data[EC_VSTORE_SLOT_SIZE];
+} __ec_align1;
/*****************************************************************************/
/* Thermal engine commands. Note that there are two implementations. We'll
@@ -1885,8 +2963,8 @@ struct ec_response_port80_last_boot {
* Version 1 separates the CPU thermal limits from the fan control.
*/
-#define EC_CMD_THERMAL_SET_THRESHOLD 0x50
-#define EC_CMD_THERMAL_GET_THRESHOLD 0x51
+#define EC_CMD_THERMAL_SET_THRESHOLD 0x0050
+#define EC_CMD_THERMAL_GET_THRESHOLD 0x0051
/* The version 0 structs are opaque. You have to know what they are for
* the get/set commands to make any sense.
@@ -1897,17 +2975,17 @@ struct ec_params_thermal_set_threshold {
uint8_t sensor_type;
uint8_t threshold_id;
uint16_t value;
-} __packed;
+} __ec_align2;
/* Version 0 - get */
struct ec_params_thermal_get_threshold {
uint8_t sensor_type;
uint8_t threshold_id;
-} __packed;
+} __ec_align1;
struct ec_response_thermal_get_threshold {
uint16_t value;
-} __packed;
+} __ec_align2;
/* The version 1 structs are visible. */
@@ -1919,71 +2997,124 @@ enum ec_temp_thresholds {
EC_TEMP_THRESH_COUNT
};
-/* Thermal configuration for one temperature sensor. Temps are in degrees K.
+/*
+ * Thermal configuration for one temperature sensor. Temps are in degrees K.
* Zero values will be silently ignored by the thermal task.
+ *
+ * Set 'temp_host' value allows thermal task to trigger some event with 1 degree
+ * hysteresis.
+ * For example,
+ * temp_host[EC_TEMP_THRESH_HIGH] = 300 K
+ * temp_host_release[EC_TEMP_THRESH_HIGH] = 0 K
+ * EC will throttle ap when temperature >= 301 K, and release throttling when
+ * temperature <= 299 K.
+ *
+ * Set 'temp_host_release' value allows thermal task has a custom hysteresis.
+ * For example,
+ * temp_host[EC_TEMP_THRESH_HIGH] = 300 K
+ * temp_host_release[EC_TEMP_THRESH_HIGH] = 295 K
+ * EC will throttle ap when temperature >= 301 K, and release throttling when
+ * temperature <= 294 K.
+ *
+ * Note that this structure is a sub-structure of
+ * ec_params_thermal_set_threshold_v1, but maintains its alignment there.
*/
struct ec_thermal_config {
uint32_t temp_host[EC_TEMP_THRESH_COUNT]; /* levels of hotness */
+ uint32_t temp_host_release[EC_TEMP_THRESH_COUNT]; /* release levels */
uint32_t temp_fan_off; /* no active cooling needed */
uint32_t temp_fan_max; /* max active cooling needed */
-} __packed;
+} __ec_align4;
/* Version 1 - get config for one sensor. */
struct ec_params_thermal_get_threshold_v1 {
uint32_t sensor_num;
-} __packed;
+} __ec_align4;
/* This returns a struct ec_thermal_config */
-/* Version 1 - set config for one sensor.
- * Use read-modify-write for best results! */
+/*
+ * Version 1 - set config for one sensor.
+ * Use read-modify-write for best results!
+ */
struct ec_params_thermal_set_threshold_v1 {
uint32_t sensor_num;
struct ec_thermal_config cfg;
-} __packed;
+} __ec_align4;
/* This returns no data */
/****************************************************************************/
/* Toggle automatic fan control */
-#define EC_CMD_THERMAL_AUTO_FAN_CTRL 0x52
+#define EC_CMD_THERMAL_AUTO_FAN_CTRL 0x0052
-/* Get TMP006 calibration data */
-#define EC_CMD_TMP006_GET_CALIBRATION 0x53
+/* Version 1 of input params */
+struct ec_params_auto_fan_ctrl_v1 {
+ uint8_t fan_idx;
+} __ec_align1;
+/* Get/Set TMP006 calibration data */
+#define EC_CMD_TMP006_GET_CALIBRATION 0x0053
+#define EC_CMD_TMP006_SET_CALIBRATION 0x0054
+
+/*
+ * The original TMP006 calibration only needed four params, but now we need
+ * more. Since the algorithm is nothing but magic numbers anyway, we'll leave
+ * the params opaque. The v1 "get" response will include the algorithm number
+ * and how many params it requires. That way we can change the EC code without
+ * needing to update this file. We can also use a different algorithm on each
+ * sensor.
+ */
+
+/* This is the same struct for both v0 and v1. */
struct ec_params_tmp006_get_calibration {
uint8_t index;
-} __packed;
+} __ec_align1;
-struct ec_response_tmp006_get_calibration {
+/* Version 0 */
+struct ec_response_tmp006_get_calibration_v0 {
float s0;
float b0;
float b1;
float b2;
-} __packed;
+} __ec_align4;
-/* Set TMP006 calibration data */
-#define EC_CMD_TMP006_SET_CALIBRATION 0x54
-
-struct ec_params_tmp006_set_calibration {
+struct ec_params_tmp006_set_calibration_v0 {
uint8_t index;
- uint8_t reserved[3]; /* Reserved; set 0 */
+ uint8_t reserved[3];
float s0;
float b0;
float b1;
float b2;
-} __packed;
+} __ec_align4;
+
+/* Version 1 */
+struct ec_response_tmp006_get_calibration_v1 {
+ uint8_t algorithm;
+ uint8_t num_params;
+ uint8_t reserved[2];
+ float val[0];
+} __ec_align4;
+
+struct ec_params_tmp006_set_calibration_v1 {
+ uint8_t index;
+ uint8_t algorithm;
+ uint8_t num_params;
+ uint8_t reserved;
+ float val[0];
+} __ec_align4;
+
/* Read raw TMP006 data */
-#define EC_CMD_TMP006_GET_RAW 0x55
+#define EC_CMD_TMP006_GET_RAW 0x0055
struct ec_params_tmp006_get_raw {
uint8_t index;
-} __packed;
+} __ec_align1;
struct ec_response_tmp006_get_raw {
int32_t t; /* In 1/100 K */
int32_t v; /* In nV */
-};
+} __ec_align4;
/*****************************************************************************/
/* MKBP - Matrix KeyBoard Protocol */
@@ -1998,24 +3129,24 @@ struct ec_response_tmp006_get_raw {
* to obtain the instantaneous state, use EC_CMD_MKBP_INFO with the type
* EC_MKBP_INFO_CURRENT and event EC_MKBP_EVENT_KEY_MATRIX.
*/
-#define EC_CMD_MKBP_STATE 0x60
+#define EC_CMD_MKBP_STATE 0x0060
/*
* Provide information about various MKBP things. See enum ec_mkbp_info_type.
*/
-#define EC_CMD_MKBP_INFO 0x61
+#define EC_CMD_MKBP_INFO 0x0061
struct ec_response_mkbp_info {
uint32_t rows;
uint32_t cols;
/* Formerly "switches", which was 0. */
uint8_t reserved;
-} __packed;
+} __ec_align_size1;
struct ec_params_mkbp_info {
uint8_t info_type;
uint8_t event_type;
-} __packed;
+} __ec_align1;
enum ec_mkbp_info_type {
/*
@@ -2057,17 +3188,28 @@ enum ec_mkbp_info_type {
};
/* Simulate key press */
-#define EC_CMD_MKBP_SIMULATE_KEY 0x62
+#define EC_CMD_MKBP_SIMULATE_KEY 0x0062
struct ec_params_mkbp_simulate_key {
uint8_t col;
uint8_t row;
uint8_t pressed;
-} __packed;
+} __ec_align1;
+
+#define EC_CMD_GET_KEYBOARD_ID 0x0063
+
+struct ec_response_keyboard_id {
+ uint32_t keyboard_id;
+} __ec_align4;
+
+enum keyboard_id {
+ KEYBOARD_ID_UNSUPPORTED = 0,
+ KEYBOARD_ID_UNREADABLE = 0xffffffff,
+};
/* Configure keyboard scanning */
-#define EC_CMD_MKBP_SET_CONFIG 0x64
-#define EC_CMD_MKBP_GET_CONFIG 0x65
+#define EC_CMD_MKBP_SET_CONFIG 0x0064
+#define EC_CMD_MKBP_GET_CONFIG 0x0065
/* flags */
enum mkbp_config_flags {
@@ -2075,16 +3217,21 @@ enum mkbp_config_flags {
};
enum mkbp_config_valid {
- EC_MKBP_VALID_SCAN_PERIOD = 1 << 0,
- EC_MKBP_VALID_POLL_TIMEOUT = 1 << 1,
- EC_MKBP_VALID_MIN_POST_SCAN_DELAY = 1 << 3,
- EC_MKBP_VALID_OUTPUT_SETTLE = 1 << 4,
- EC_MKBP_VALID_DEBOUNCE_DOWN = 1 << 5,
- EC_MKBP_VALID_DEBOUNCE_UP = 1 << 6,
- EC_MKBP_VALID_FIFO_MAX_DEPTH = 1 << 7,
+ EC_MKBP_VALID_SCAN_PERIOD = BIT(0),
+ EC_MKBP_VALID_POLL_TIMEOUT = BIT(1),
+ EC_MKBP_VALID_MIN_POST_SCAN_DELAY = BIT(3),
+ EC_MKBP_VALID_OUTPUT_SETTLE = BIT(4),
+ EC_MKBP_VALID_DEBOUNCE_DOWN = BIT(5),
+ EC_MKBP_VALID_DEBOUNCE_UP = BIT(6),
+ EC_MKBP_VALID_FIFO_MAX_DEPTH = BIT(7),
};
-/* Configuration for our key scanning algorithm */
+/*
+ * Configuration for our key scanning algorithm.
+ *
+ * Note that this is used as a sub-structure of
+ * ec_{params/response}_mkbp_get_config.
+ */
struct ec_mkbp_config {
uint32_t valid_mask; /* valid fields */
uint8_t flags; /* some flags (enum mkbp_config_flags) */
@@ -2104,18 +3251,18 @@ struct ec_mkbp_config {
uint16_t debounce_up_us; /* time for debounce on key up */
/* maximum depth to allow for fifo (0 = no keyscan output) */
uint8_t fifo_max_depth;
-} __packed;
+} __ec_align_size1;
struct ec_params_mkbp_set_config {
struct ec_mkbp_config config;
-} __packed;
+} __ec_align_size1;
struct ec_response_mkbp_get_config {
struct ec_mkbp_config config;
-} __packed;
+} __ec_align_size1;
/* Run the key scan emulation */
-#define EC_CMD_KEYSCAN_SEQ_CTRL 0x66
+#define EC_CMD_KEYSCAN_SEQ_CTRL 0x0066
enum ec_keyscan_seq_cmd {
EC_KEYSCAN_SEQ_STATUS = 0, /* Get status information */
@@ -2130,23 +3277,23 @@ enum ec_collect_flags {
* Indicates this scan was processed by the EC. Due to timing, some
* scans may be skipped.
*/
- EC_KEYSCAN_SEQ_FLAG_DONE = 1 << 0,
+ EC_KEYSCAN_SEQ_FLAG_DONE = BIT(0),
};
struct ec_collect_item {
uint8_t flags; /* some flags (enum ec_collect_flags) */
-};
+} __ec_align1;
struct ec_params_keyscan_seq_ctrl {
uint8_t cmd; /* Command to send (enum ec_keyscan_seq_cmd) */
union {
- struct {
+ struct __ec_align1 {
uint8_t active; /* still active */
uint8_t num_items; /* number of items */
/* Current item being presented */
uint8_t cur_item;
} status;
- struct {
+ struct __ec_todo_unpacked {
/*
* Absolute time for this scan, measured from the
* start of the sequence.
@@ -2154,29 +3301,40 @@ struct ec_params_keyscan_seq_ctrl {
uint32_t time_us;
uint8_t scan[0]; /* keyscan data */
} add;
- struct {
+ struct __ec_align1 {
uint8_t start_item; /* First item to return */
uint8_t num_items; /* Number of items to return */
} collect;
};
-} __packed;
+} __ec_todo_packed;
struct ec_result_keyscan_seq_ctrl {
union {
- struct {
+ struct __ec_todo_unpacked {
uint8_t num_items; /* Number of items */
/* Data for each item */
struct ec_collect_item item[0];
} collect;
};
-} __packed;
+} __ec_todo_packed;
/*
- * Command for retrieving the next pending MKBP event from the EC device
+ * Get the next pending MKBP event.
*
- * The device replies with UNAVAILABLE if there aren't any pending events.
+ * Returns EC_RES_UNAVAILABLE if there is no event pending.
*/
-#define EC_CMD_GET_NEXT_EVENT 0x67
+#define EC_CMD_GET_NEXT_EVENT 0x0067
+
+#define EC_MKBP_HAS_MORE_EVENTS_SHIFT 7
+
+/*
+ * We use the most significant bit of the event type to indicate to the host
+ * that the EC has more MKBP events available to provide.
+ */
+#define EC_MKBP_HAS_MORE_EVENTS BIT(EC_MKBP_HAS_MORE_EVENTS_SHIFT)
+
+/* The mask to apply to get the raw event type */
+#define EC_MKBP_EVENT_TYPE_MASK (BIT(EC_MKBP_HAS_MORE_EVENTS_SHIFT) - 1)
enum ec_mkbp_event {
/* Keyboard matrix changed. The event data is the new matrix state. */
@@ -2194,9 +3352,21 @@ enum ec_mkbp_event {
/* The state of the switches have changed. */
EC_MKBP_EVENT_SWITCH = 4,
- /* EC sent a sysrq command */
+ /* New Fingerprint sensor event, the event data is fp_events bitmap. */
+ EC_MKBP_EVENT_FINGERPRINT = 5,
+
+ /*
+ * Sysrq event: send emulated sysrq. The event data is sysrq,
+ * corresponding to the key to be pressed.
+ */
EC_MKBP_EVENT_SYSRQ = 6,
+ /*
+ * New 64-bit host event.
+ * The event data is 8 bytes of host event flags.
+ */
+ EC_MKBP_EVENT_HOST_EVENT64 = 7,
+
/* Notify the AP that something happened on CEC */
EC_MKBP_EVENT_CEC_EVENT = 8,
@@ -2206,65 +3376,140 @@ enum ec_mkbp_event {
/* Number of MKBP events */
EC_MKBP_EVENT_COUNT,
};
+BUILD_ASSERT(EC_MKBP_EVENT_COUNT <= EC_MKBP_EVENT_TYPE_MASK);
-union ec_response_get_next_data {
- uint8_t key_matrix[13];
+union __ec_align_offset1 ec_response_get_next_data {
+ uint8_t key_matrix[13];
/* Unaligned */
- uint32_t host_event;
-
- uint32_t buttons;
- uint32_t switches;
- uint32_t sysrq;
-} __packed;
-
-union ec_response_get_next_data_v1 {
- uint8_t key_matrix[16];
uint32_t host_event;
+ uint64_t host_event64;
+
+ struct __ec_todo_unpacked {
+ /* For aligning the fifo_info */
+ uint8_t reserved[3];
+ struct ec_response_motion_sense_fifo_info info;
+ } sensor_fifo;
+
uint32_t buttons;
+
uint32_t switches;
+
+ uint32_t fp_events;
+
uint32_t sysrq;
+
+ /* CEC events from enum mkbp_cec_event */
uint32_t cec_events;
+};
+
+union __ec_align_offset1 ec_response_get_next_data_v1 {
+ uint8_t key_matrix[16];
+
+ /* Unaligned */
+ uint32_t host_event;
+ uint64_t host_event64;
+
+ struct __ec_todo_unpacked {
+ /* For aligning the fifo_info */
+ uint8_t reserved[3];
+ struct ec_response_motion_sense_fifo_info info;
+ } sensor_fifo;
+
+ uint32_t buttons;
+
+ uint32_t switches;
+
+ uint32_t fp_events;
+
+ uint32_t sysrq;
+
+ /* CEC events from enum mkbp_cec_event */
+ uint32_t cec_events;
+
uint8_t cec_message[16];
-} __packed;
+};
+BUILD_ASSERT(sizeof(union ec_response_get_next_data_v1) == 16);
struct ec_response_get_next_event {
uint8_t event_type;
/* Followed by event data if any */
union ec_response_get_next_data data;
-} __packed;
+} __ec_align1;
struct ec_response_get_next_event_v1 {
uint8_t event_type;
/* Followed by event data if any */
union ec_response_get_next_data_v1 data;
-} __packed;
+} __ec_align1;
/* Bit indices for buttons and switches.*/
/* Buttons */
#define EC_MKBP_POWER_BUTTON 0
#define EC_MKBP_VOL_UP 1
#define EC_MKBP_VOL_DOWN 2
+#define EC_MKBP_RECOVERY 3
/* Switches */
#define EC_MKBP_LID_OPEN 0
#define EC_MKBP_TABLET_MODE 1
#define EC_MKBP_BASE_ATTACHED 2
+/* Run keyboard factory test scanning */
+#define EC_CMD_KEYBOARD_FACTORY_TEST 0x0068
+
+struct ec_response_keyboard_factory_test {
+ uint16_t shorted; /* Keyboard pins are shorted */
+} __ec_align2;
+
+/* Fingerprint events in 'fp_events' for EC_MKBP_EVENT_FINGERPRINT */
+#define EC_MKBP_FP_RAW_EVENT(fp_events) ((fp_events) & 0x00FFFFFF)
+#define EC_MKBP_FP_ERRCODE(fp_events) ((fp_events) & 0x0000000F)
+#define EC_MKBP_FP_ENROLL_PROGRESS_OFFSET 4
+#define EC_MKBP_FP_ENROLL_PROGRESS(fpe) (((fpe) & 0x00000FF0) \
+ >> EC_MKBP_FP_ENROLL_PROGRESS_OFFSET)
+#define EC_MKBP_FP_MATCH_IDX_OFFSET 12
+#define EC_MKBP_FP_MATCH_IDX_MASK 0x0000F000
+#define EC_MKBP_FP_MATCH_IDX(fpe) (((fpe) & EC_MKBP_FP_MATCH_IDX_MASK) \
+ >> EC_MKBP_FP_MATCH_IDX_OFFSET)
+#define EC_MKBP_FP_ENROLL BIT(27)
+#define EC_MKBP_FP_MATCH BIT(28)
+#define EC_MKBP_FP_FINGER_DOWN BIT(29)
+#define EC_MKBP_FP_FINGER_UP BIT(30)
+#define EC_MKBP_FP_IMAGE_READY BIT(31)
+/* code given by EC_MKBP_FP_ERRCODE() when EC_MKBP_FP_ENROLL is set */
+#define EC_MKBP_FP_ERR_ENROLL_OK 0
+#define EC_MKBP_FP_ERR_ENROLL_LOW_QUALITY 1
+#define EC_MKBP_FP_ERR_ENROLL_IMMOBILE 2
+#define EC_MKBP_FP_ERR_ENROLL_LOW_COVERAGE 3
+#define EC_MKBP_FP_ERR_ENROLL_INTERNAL 5
+/* Can be used to detect if image was usable for enrollment or not. */
+#define EC_MKBP_FP_ERR_ENROLL_PROBLEM_MASK 1
+/* code given by EC_MKBP_FP_ERRCODE() when EC_MKBP_FP_MATCH is set */
+#define EC_MKBP_FP_ERR_MATCH_NO 0
+#define EC_MKBP_FP_ERR_MATCH_NO_INTERNAL 6
+#define EC_MKBP_FP_ERR_MATCH_NO_TEMPLATES 7
+#define EC_MKBP_FP_ERR_MATCH_NO_LOW_QUALITY 2
+#define EC_MKBP_FP_ERR_MATCH_NO_LOW_COVERAGE 4
+#define EC_MKBP_FP_ERR_MATCH_YES 1
+#define EC_MKBP_FP_ERR_MATCH_YES_UPDATED 3
+#define EC_MKBP_FP_ERR_MATCH_YES_UPDATE_FAILED 5
+
+
/*****************************************************************************/
/* Temperature sensor commands */
/* Read temperature sensor info */
-#define EC_CMD_TEMP_SENSOR_GET_INFO 0x70
+#define EC_CMD_TEMP_SENSOR_GET_INFO 0x0070
struct ec_params_temp_sensor_get_info {
uint8_t id;
-} __packed;
+} __ec_align1;
struct ec_response_temp_sensor_get_info {
char sensor_name[32];
uint8_t sensor_type;
-} __packed;
+} __ec_align1;
/*****************************************************************************/
@@ -2277,49 +3522,131 @@ struct ec_response_temp_sensor_get_info {
/*****************************************************************************/
/* Host event commands */
+
+/* Obsolete. New implementation should use EC_CMD_HOST_EVENT instead */
/*
* Host event mask params and response structures, shared by all of the host
* event commands below.
*/
struct ec_params_host_event_mask {
uint32_t mask;
-} __packed;
+} __ec_align4;
struct ec_response_host_event_mask {
uint32_t mask;
-} __packed;
+} __ec_align4;
/* These all use ec_response_host_event_mask */
-#define EC_CMD_HOST_EVENT_GET_B 0x87
-#define EC_CMD_HOST_EVENT_GET_SMI_MASK 0x88
-#define EC_CMD_HOST_EVENT_GET_SCI_MASK 0x89
-#define EC_CMD_HOST_EVENT_GET_WAKE_MASK 0x8d
+#define EC_CMD_HOST_EVENT_GET_B 0x0087
+#define EC_CMD_HOST_EVENT_GET_SMI_MASK 0x0088
+#define EC_CMD_HOST_EVENT_GET_SCI_MASK 0x0089
+#define EC_CMD_HOST_EVENT_GET_WAKE_MASK 0x008D
/* These all use ec_params_host_event_mask */
-#define EC_CMD_HOST_EVENT_SET_SMI_MASK 0x8a
-#define EC_CMD_HOST_EVENT_SET_SCI_MASK 0x8b
-#define EC_CMD_HOST_EVENT_CLEAR 0x8c
-#define EC_CMD_HOST_EVENT_SET_WAKE_MASK 0x8e
-#define EC_CMD_HOST_EVENT_CLEAR_B 0x8f
+#define EC_CMD_HOST_EVENT_SET_SMI_MASK 0x008A
+#define EC_CMD_HOST_EVENT_SET_SCI_MASK 0x008B
+#define EC_CMD_HOST_EVENT_CLEAR 0x008C
+#define EC_CMD_HOST_EVENT_SET_WAKE_MASK 0x008E
+#define EC_CMD_HOST_EVENT_CLEAR_B 0x008F
+
+/*
+ * Unified host event programming interface - Should be used by newer versions
+ * of BIOS/OS to program host events and masks
+ */
+
+struct ec_params_host_event {
+
+ /* Action requested by host - one of enum ec_host_event_action. */
+ uint8_t action;
+
+ /*
+ * Mask type that the host requested the action on - one of
+ * enum ec_host_event_mask_type.
+ */
+ uint8_t mask_type;
+
+ /* Set to 0, ignore on read */
+ uint16_t reserved;
+
+ /* Value to be used in case of set operations. */
+ uint64_t value;
+} __ec_align4;
+
+/*
+ * Response structure returned by EC_CMD_HOST_EVENT.
+ * Update the value on a GET request. Set to 0 on GET/CLEAR
+ */
+
+struct ec_response_host_event {
+
+ /* Mask value in case of get operation */
+ uint64_t value;
+} __ec_align4;
+
+enum ec_host_event_action {
+ /*
+ * params.value is ignored. Value of mask_type populated
+ * in response.value
+ */
+ EC_HOST_EVENT_GET,
+
+ /* Bits in params.value are set */
+ EC_HOST_EVENT_SET,
+
+ /* Bits in params.value are cleared */
+ EC_HOST_EVENT_CLEAR,
+};
+
+enum ec_host_event_mask_type {
+
+ /* Main host event copy */
+ EC_HOST_EVENT_MAIN,
+
+ /* Copy B of host events */
+ EC_HOST_EVENT_B,
+
+ /* SCI Mask */
+ EC_HOST_EVENT_SCI_MASK,
+
+ /* SMI Mask */
+ EC_HOST_EVENT_SMI_MASK,
+
+ /* Mask of events that should be always reported in hostevents */
+ EC_HOST_EVENT_ALWAYS_REPORT_MASK,
+
+ /* Active wake mask */
+ EC_HOST_EVENT_ACTIVE_WAKE_MASK,
+
+ /* Lazy wake mask for S0ix */
+ EC_HOST_EVENT_LAZY_WAKE_MASK_S0IX,
+
+ /* Lazy wake mask for S3 */
+ EC_HOST_EVENT_LAZY_WAKE_MASK_S3,
+
+ /* Lazy wake mask for S5 */
+ EC_HOST_EVENT_LAZY_WAKE_MASK_S5,
+};
+
+#define EC_CMD_HOST_EVENT 0x00A4
/*****************************************************************************/
/* Switch commands */
/* Enable/disable LCD backlight */
-#define EC_CMD_SWITCH_ENABLE_BKLIGHT 0x90
+#define EC_CMD_SWITCH_ENABLE_BKLIGHT 0x0090
struct ec_params_switch_enable_backlight {
uint8_t enabled;
-} __packed;
+} __ec_align1;
/* Enable/disable WLAN/Bluetooth */
-#define EC_CMD_SWITCH_ENABLE_WIRELESS 0x91
+#define EC_CMD_SWITCH_ENABLE_WIRELESS 0x0091
#define EC_VER_SWITCH_ENABLE_WIRELESS 1
/* Version 0 params; no response */
struct ec_params_switch_enable_wireless_v0 {
uint8_t enabled;
-} __packed;
+} __ec_align1;
/* Version 1 params */
struct ec_params_switch_enable_wireless_v1 {
@@ -2338,7 +3665,7 @@ struct ec_params_switch_enable_wireless_v1 {
/* Which flags to copy from suspend_flags */
uint8_t suspend_mask;
-} __packed;
+} __ec_align1;
/* Version 1 response */
struct ec_response_switch_enable_wireless_v1 {
@@ -2347,55 +3674,56 @@ struct ec_response_switch_enable_wireless_v1 {
/* Flags to leave enabled in S3 */
uint8_t suspend_flags;
-} __packed;
+} __ec_align1;
/*****************************************************************************/
/* GPIO commands. Only available on EC if write protect has been disabled. */
/* Set GPIO output value */
-#define EC_CMD_GPIO_SET 0x92
+#define EC_CMD_GPIO_SET 0x0092
struct ec_params_gpio_set {
char name[32];
uint8_t val;
-} __packed;
+} __ec_align1;
/* Get GPIO value */
-#define EC_CMD_GPIO_GET 0x93
+#define EC_CMD_GPIO_GET 0x0093
/* Version 0 of input params and response */
struct ec_params_gpio_get {
char name[32];
-} __packed;
+} __ec_align1;
+
struct ec_response_gpio_get {
uint8_t val;
-} __packed;
+} __ec_align1;
/* Version 1 of input params and response */
struct ec_params_gpio_get_v1 {
uint8_t subcmd;
union {
- struct {
+ struct __ec_align1 {
char name[32];
} get_value_by_name;
- struct {
+ struct __ec_align1 {
uint8_t index;
} get_info;
};
-} __packed;
+} __ec_align1;
struct ec_response_gpio_get_v1 {
union {
- struct {
+ struct __ec_align1 {
uint8_t val;
} get_value_by_name, get_count;
- struct {
+ struct __ec_todo_unpacked {
uint8_t val;
char name[32];
uint32_t flags;
} get_info;
};
-} __packed;
+} __ec_todo_packed;
enum gpio_get_subcmd {
EC_GPIO_GET_BY_NAME = 0,
@@ -2407,25 +3735,28 @@ enum gpio_get_subcmd {
/* I2C commands. Only available when flash write protect is unlocked. */
/*
- * TODO(crosbug.com/p/23570): These commands are deprecated, and will be
- * removed soon. Use EC_CMD_I2C_XFER instead.
+ * CAUTION: These commands are deprecated, and are not supported anymore in EC
+ * builds >= 8398.0.0 (see crosbug.com/p/23570).
+ *
+ * Use EC_CMD_I2C_PASSTHRU instead.
*/
/* Read I2C bus */
-#define EC_CMD_I2C_READ 0x94
+#define EC_CMD_I2C_READ 0x0094
struct ec_params_i2c_read {
uint16_t addr; /* 8-bit address (7-bit shifted << 1) */
uint8_t read_size; /* Either 8 or 16. */
uint8_t port;
uint8_t offset;
-} __packed;
+} __ec_align_size1;
+
struct ec_response_i2c_read {
uint16_t data;
-} __packed;
+} __ec_align2;
/* Write I2C bus */
-#define EC_CMD_I2C_WRITE 0x95
+#define EC_CMD_I2C_WRITE 0x0095
struct ec_params_i2c_write {
uint16_t data;
@@ -2433,7 +3764,7 @@ struct ec_params_i2c_write {
uint8_t write_size; /* Either 8 or 16. */
uint8_t port;
uint8_t offset;
-} __packed;
+} __ec_align_size1;
/*****************************************************************************/
/* Charge state commands. Only available when flash write protect unlocked. */
@@ -2441,7 +3772,7 @@ struct ec_params_i2c_write {
/* Force charge state machine to stop charging the battery or force it to
* discharge the battery.
*/
-#define EC_CMD_CHARGE_CONTROL 0x96
+#define EC_CMD_CHARGE_CONTROL 0x0096
#define EC_VER_CHARGE_CONTROL 1
enum ec_charge_control_mode {
@@ -2452,13 +3783,12 @@ enum ec_charge_control_mode {
struct ec_params_charge_control {
uint32_t mode; /* enum charge_control_mode */
-} __packed;
+} __ec_align4;
/*****************************************************************************/
-/* Console commands. Only available when flash write protect is unlocked. */
/* Snapshot console output buffer for use by EC_CMD_CONSOLE_READ. */
-#define EC_CMD_CONSOLE_SNAPSHOT 0x97
+#define EC_CMD_CONSOLE_SNAPSHOT 0x0097
/*
* Read data from the saved snapshot. If the subcmd parameter is
@@ -2472,7 +3802,7 @@ struct ec_params_charge_control {
* Response is null-terminated string. Empty string, if there is no more
* remaining output.
*/
-#define EC_CMD_CONSOLE_READ 0x98
+#define EC_CMD_CONSOLE_READ 0x0098
enum ec_console_read_subcmd {
CONSOLE_READ_NEXT = 0,
@@ -2481,7 +3811,7 @@ enum ec_console_read_subcmd {
struct ec_params_console_read_v1 {
uint8_t subcmd; /* enum ec_console_read_subcmd */
-} __packed;
+} __ec_align1;
/*****************************************************************************/
@@ -2492,14 +3822,13 @@ struct ec_params_console_read_v1 {
* EC_RES_SUCCESS if the command was successful.
* EC_RES_ERROR if the cut off command failed.
*/
+#define EC_CMD_BATTERY_CUT_OFF 0x0099
-#define EC_CMD_BATTERY_CUT_OFF 0x99
-
-#define EC_BATTERY_CUTOFF_FLAG_AT_SHUTDOWN (1 << 0)
+#define EC_BATTERY_CUTOFF_FLAG_AT_SHUTDOWN BIT(0)
struct ec_params_battery_cutoff {
uint8_t flags;
-} __packed;
+} __ec_align1;
/*****************************************************************************/
/* USB port mux control. */
@@ -2507,11 +3836,11 @@ struct ec_params_battery_cutoff {
/*
* Switch USB mux or return to automatic switching.
*/
-#define EC_CMD_USB_MUX 0x9a
+#define EC_CMD_USB_MUX 0x009A
struct ec_params_usb_mux {
uint8_t mux;
-} __packed;
+} __ec_align1;
/*****************************************************************************/
/* LDOs / FETs control. */
@@ -2524,25 +3853,25 @@ enum ec_ldo_state {
/*
* Switch on/off a LDO.
*/
-#define EC_CMD_LDO_SET 0x9b
+#define EC_CMD_LDO_SET 0x009B
struct ec_params_ldo_set {
uint8_t index;
uint8_t state;
-} __packed;
+} __ec_align1;
/*
* Get LDO state.
*/
-#define EC_CMD_LDO_GET 0x9c
+#define EC_CMD_LDO_GET 0x009C
struct ec_params_ldo_get {
uint8_t index;
-} __packed;
+} __ec_align1;
struct ec_response_ldo_get {
uint8_t state;
-} __packed;
+} __ec_align1;
/*****************************************************************************/
/* Power info. */
@@ -2550,7 +3879,7 @@ struct ec_response_ldo_get {
/*
* Get power info.
*/
-#define EC_CMD_POWER_INFO 0x9d
+#define EC_CMD_POWER_INFO 0x009D
struct ec_response_power_info {
uint32_t usb_dev_type;
@@ -2558,21 +3887,21 @@ struct ec_response_power_info {
uint16_t voltage_system;
uint16_t current_system;
uint16_t usb_current_limit;
-} __packed;
+} __ec_align4;
/*****************************************************************************/
/* I2C passthru command */
-#define EC_CMD_I2C_PASSTHRU 0x9e
+#define EC_CMD_I2C_PASSTHRU 0x009E
/* Read data; if not present, message is a write */
-#define EC_I2C_FLAG_READ (1 << 15)
+#define EC_I2C_FLAG_READ BIT(15)
/* Mask for address */
#define EC_I2C_ADDR_MASK 0x3ff
-#define EC_I2C_STATUS_NAK (1 << 0) /* Transfer was not acknowledged */
-#define EC_I2C_STATUS_TIMEOUT (1 << 1) /* Timeout during transfer */
+#define EC_I2C_STATUS_NAK BIT(0) /* Transfer was not acknowledged */
+#define EC_I2C_STATUS_TIMEOUT BIT(1) /* Timeout during transfer */
/* Any error */
#define EC_I2C_STATUS_ERROR (EC_I2C_STATUS_NAK | EC_I2C_STATUS_TIMEOUT)
@@ -2580,49 +3909,49 @@ struct ec_response_power_info {
struct ec_params_i2c_passthru_msg {
uint16_t addr_flags; /* I2C slave address (7 or 10 bits) and flags */
uint16_t len; /* Number of bytes to read or write */
-} __packed;
+} __ec_align2;
struct ec_params_i2c_passthru {
uint8_t port; /* I2C port number */
uint8_t num_msgs; /* Number of messages */
struct ec_params_i2c_passthru_msg msg[];
/* Data to write for all messages is concatenated here */
-} __packed;
+} __ec_align2;
struct ec_response_i2c_passthru {
uint8_t i2c_status; /* Status flags (EC_I2C_STATUS_...) */
uint8_t num_msgs; /* Number of messages processed */
uint8_t data[]; /* Data read by messages concatenated here */
-} __packed;
+} __ec_align1;
/*****************************************************************************/
/* Power button hang detect */
-#define EC_CMD_HANG_DETECT 0x9f
+#define EC_CMD_HANG_DETECT 0x009F
/* Reasons to start hang detection timer */
/* Power button pressed */
-#define EC_HANG_START_ON_POWER_PRESS (1 << 0)
+#define EC_HANG_START_ON_POWER_PRESS BIT(0)
/* Lid closed */
-#define EC_HANG_START_ON_LID_CLOSE (1 << 1)
+#define EC_HANG_START_ON_LID_CLOSE BIT(1)
/* Lid opened */
-#define EC_HANG_START_ON_LID_OPEN (1 << 2)
+#define EC_HANG_START_ON_LID_OPEN BIT(2)
/* Start of AP S3->S0 transition (booting or resuming from suspend) */
-#define EC_HANG_START_ON_RESUME (1 << 3)
+#define EC_HANG_START_ON_RESUME BIT(3)
/* Reasons to cancel hang detection */
/* Power button released */
-#define EC_HANG_STOP_ON_POWER_RELEASE (1 << 8)
+#define EC_HANG_STOP_ON_POWER_RELEASE BIT(8)
/* Any host command from AP received */
-#define EC_HANG_STOP_ON_HOST_COMMAND (1 << 9)
+#define EC_HANG_STOP_ON_HOST_COMMAND BIT(9)
/* Stop on end of AP S0->S3 transition (suspending or shutting down) */
-#define EC_HANG_STOP_ON_SUSPEND (1 << 10)
+#define EC_HANG_STOP_ON_SUSPEND BIT(10)
/*
* If this flag is set, all the other fields are ignored, and the hang detect
@@ -2630,14 +3959,14 @@ struct ec_response_i2c_passthru {
* without reconfiguring any of the other hang detect settings. Note that
* you must previously have configured the timeouts.
*/
-#define EC_HANG_START_NOW (1 << 30)
+#define EC_HANG_START_NOW BIT(30)
/*
* If this flag is set, all the other fields are ignored (including
* EC_HANG_START_NOW). This provides the AP a way to stop the hang timer
* without reconfiguring any of the other hang detect settings.
*/
-#define EC_HANG_STOP_NOW (1 << 31)
+#define EC_HANG_STOP_NOW BIT(31)
struct ec_params_hang_detect {
/* Flags; see EC_HANG_* */
@@ -2648,7 +3977,7 @@ struct ec_params_hang_detect {
/* Timeout in msec before generating warm reboot, if enabled */
uint16_t warm_reboot_timeout_msec;
-} __packed;
+} __ec_align4;
/*****************************************************************************/
/* Commands for battery charging */
@@ -2657,7 +3986,7 @@ struct ec_params_hang_detect {
* This is the single catch-all host command to exchange data regarding the
* charge state machine (v2 and up).
*/
-#define EC_CMD_CHARGE_STATE 0xa0
+#define EC_CMD_CHARGE_STATE 0x00A0
/* Subcommands for this host command */
enum charge_state_command {
@@ -2677,6 +4006,11 @@ enum charge_state_params {
CS_PARAM_CHG_INPUT_CURRENT, /* charger input current limit */
CS_PARAM_CHG_STATUS, /* charger-specific status */
CS_PARAM_CHG_OPTION, /* charger-specific options */
+ CS_PARAM_LIMIT_POWER, /*
+ * Check if power is limited due to
+ * low battery and / or a weak external
+ * charger. READ ONLY.
+ */
/* How many so far? */
CS_NUM_BASE_PARAMS,
@@ -2684,30 +4018,39 @@ enum charge_state_params {
CS_PARAM_CUSTOM_PROFILE_MIN = 0x10000,
CS_PARAM_CUSTOM_PROFILE_MAX = 0x1ffff,
+ /* Range for CONFIG_CHARGE_STATE_DEBUG params */
+ CS_PARAM_DEBUG_MIN = 0x20000,
+ CS_PARAM_DEBUG_CTL_MODE = 0x20000,
+ CS_PARAM_DEBUG_MANUAL_MODE,
+ CS_PARAM_DEBUG_SEEMS_DEAD,
+ CS_PARAM_DEBUG_SEEMS_DISCONNECTED,
+ CS_PARAM_DEBUG_BATT_REMOVED,
+ CS_PARAM_DEBUG_MANUAL_CURRENT,
+ CS_PARAM_DEBUG_MANUAL_VOLTAGE,
+ CS_PARAM_DEBUG_MAX = 0x2ffff,
+
/* Other custom param ranges go here... */
};
struct ec_params_charge_state {
uint8_t cmd; /* enum charge_state_command */
union {
- struct {
- /* no args */
- } get_state;
+ /* get_state has no args */
- struct {
+ struct __ec_todo_unpacked {
uint32_t param; /* enum charge_state_param */
} get_param;
- struct {
+ struct __ec_todo_unpacked {
uint32_t param; /* param to set */
uint32_t value; /* value to set */
} set_param;
};
-} __packed;
+} __ec_todo_packed;
struct ec_response_charge_state {
union {
- struct {
+ struct __ec_align4 {
int ac;
int chg_voltage;
int chg_current;
@@ -2715,24 +4058,23 @@ struct ec_response_charge_state {
int batt_state_of_charge;
} get_state;
- struct {
+ struct __ec_align4 {
uint32_t value;
} get_param;
- struct {
- /* no return values */
- } set_param;
+
+ /* set_param returns no args */
};
-} __packed;
+} __ec_align4;
/*
* Set maximum battery charging current.
*/
-#define EC_CMD_CHARGE_CURRENT_LIMIT 0xa1
+#define EC_CMD_CHARGE_CURRENT_LIMIT 0x00A1
struct ec_params_current_limit {
uint32_t limit; /* in mA */
-} __packed;
+} __ec_align4;
/*
* Set maximum external voltage / current.
@@ -2743,23 +4085,69 @@ struct ec_params_current_limit {
struct ec_params_external_power_limit_v1 {
uint16_t current_lim; /* in mA, or EC_POWER_LIMIT_NONE to clear limit */
uint16_t voltage_lim; /* in mV, or EC_POWER_LIMIT_NONE to clear limit */
-} __packed;
+} __ec_align2;
#define EC_POWER_LIMIT_NONE 0xffff
+/*
+ * Set maximum voltage & current of a dedicated charge port
+ */
+#define EC_CMD_OVERRIDE_DEDICATED_CHARGER_LIMIT 0x00A3
+
+struct ec_params_dedicated_charger_limit {
+ uint16_t current_lim; /* in mA */
+ uint16_t voltage_lim; /* in mV */
+} __ec_align2;
+
+/*****************************************************************************/
+/* Hibernate/Deep Sleep Commands */
+
+/* Set the delay before going into hibernation. */
+#define EC_CMD_HIBERNATION_DELAY 0x00A8
+
+struct ec_params_hibernation_delay {
+ /*
+ * Seconds to wait in G3 before hibernate. Pass in 0 to read the
+ * current settings without changing them.
+ */
+ uint32_t seconds;
+} __ec_align4;
+
+struct ec_response_hibernation_delay {
+ /*
+ * The current time in seconds in which the system has been in the G3
+ * state. This value is reset if the EC transitions out of G3.
+ */
+ uint32_t time_g3;
+
+ /*
+ * The current time remaining in seconds until the EC should hibernate.
+ * This value is also reset if the EC transitions out of G3.
+ */
+ uint32_t time_remaining;
+
+ /*
+ * The current time in seconds that the EC should wait in G3 before
+ * hibernating.
+ */
+ uint32_t hibernate_delay;
+} __ec_align4;
+
/* Inform the EC when entering a sleep state */
-#define EC_CMD_HOST_SLEEP_EVENT 0xa9
+#define EC_CMD_HOST_SLEEP_EVENT 0x00A9
enum host_sleep_event {
HOST_SLEEP_EVENT_S3_SUSPEND = 1,
HOST_SLEEP_EVENT_S3_RESUME = 2,
HOST_SLEEP_EVENT_S0IX_SUSPEND = 3,
- HOST_SLEEP_EVENT_S0IX_RESUME = 4
+ HOST_SLEEP_EVENT_S0IX_RESUME = 4,
+ /* S3 suspend with additional enabled wake sources */
+ HOST_SLEEP_EVENT_S3_WAKEABLE_SUSPEND = 5,
};
struct ec_params_host_sleep_event {
uint8_t sleep_event;
-} __packed;
+} __ec_align1;
/*
* Use a default timeout value (CONFIG_SLEEP_TIMEOUT_MS) for detecting sleep
@@ -2790,7 +4178,7 @@ struct ec_params_host_sleep_event_v1 {
/* No parameters for non-suspend messages. */
};
-} __packed;
+} __ec_align2;
/* A timeout occurred when this bit is set */
#define EC_HOST_RESUME_SLEEP_TIMEOUT 0x80000000
@@ -2816,42 +4204,72 @@ struct ec_response_host_sleep_event_v1 {
/* No response fields for non-resume messages. */
};
-} __packed;
+} __ec_align4;
+
+/*****************************************************************************/
+/* Device events */
+#define EC_CMD_DEVICE_EVENT 0x00AA
+
+enum ec_device_event {
+ EC_DEVICE_EVENT_TRACKPAD,
+ EC_DEVICE_EVENT_DSP,
+ EC_DEVICE_EVENT_WIFI,
+};
+
+enum ec_device_event_param {
+ /* Get and clear pending device events */
+ EC_DEVICE_EVENT_PARAM_GET_CURRENT_EVENTS,
+ /* Get device event mask */
+ EC_DEVICE_EVENT_PARAM_GET_ENABLED_EVENTS,
+ /* Set device event mask */
+ EC_DEVICE_EVENT_PARAM_SET_ENABLED_EVENTS,
+};
+
+#define EC_DEVICE_EVENT_MASK(event_code) BIT(event_code % 32)
+
+struct ec_params_device_event {
+ uint32_t event_mask;
+ uint8_t param;
+} __ec_align_size1;
+
+struct ec_response_device_event {
+ uint32_t event_mask;
+} __ec_align4;
/*****************************************************************************/
/* Smart battery pass-through */
/* Get / Set 16-bit smart battery registers */
-#define EC_CMD_SB_READ_WORD 0xb0
-#define EC_CMD_SB_WRITE_WORD 0xb1
+#define EC_CMD_SB_READ_WORD 0x00B0
+#define EC_CMD_SB_WRITE_WORD 0x00B1
/* Get / Set string smart battery parameters
* formatted as SMBUS "block".
*/
-#define EC_CMD_SB_READ_BLOCK 0xb2
-#define EC_CMD_SB_WRITE_BLOCK 0xb3
+#define EC_CMD_SB_READ_BLOCK 0x00B2
+#define EC_CMD_SB_WRITE_BLOCK 0x00B3
struct ec_params_sb_rd {
uint8_t reg;
-} __packed;
+} __ec_align1;
struct ec_response_sb_rd_word {
uint16_t value;
-} __packed;
+} __ec_align2;
struct ec_params_sb_wr_word {
uint8_t reg;
uint16_t value;
-} __packed;
+} __ec_align1;
struct ec_response_sb_rd_block {
uint8_t data[32];
-} __packed;
+} __ec_align1;
struct ec_params_sb_wr_block {
uint8_t reg;
uint16_t data[32];
-} __packed;
+} __ec_align1;
/*****************************************************************************/
/* Battery vendor parameters
@@ -2862,7 +4280,7 @@ struct ec_params_sb_wr_block {
* requested value.
*/
-#define EC_CMD_BATTERY_VENDOR_PARAM 0xb4
+#define EC_CMD_BATTERY_VENDOR_PARAM 0x00B4
enum ec_battery_vendor_param_mode {
BATTERY_VENDOR_PARAM_MODE_GET = 0,
@@ -2873,16 +4291,187 @@ struct ec_params_battery_vendor_param {
uint32_t param;
uint32_t value;
uint8_t mode;
-} __packed;
+} __ec_align_size1;
struct ec_response_battery_vendor_param {
uint32_t value;
-} __packed;
+} __ec_align4;
/*****************************************************************************/
+/*
+ * Smart Battery Firmware Update Commands
+ */
+#define EC_CMD_SB_FW_UPDATE 0x00B5
+
+enum ec_sb_fw_update_subcmd {
+ EC_SB_FW_UPDATE_PREPARE = 0x0,
+ EC_SB_FW_UPDATE_INFO = 0x1, /*query sb info */
+ EC_SB_FW_UPDATE_BEGIN = 0x2, /*check if protected */
+ EC_SB_FW_UPDATE_WRITE = 0x3, /*check if protected */
+ EC_SB_FW_UPDATE_END = 0x4,
+ EC_SB_FW_UPDATE_STATUS = 0x5,
+ EC_SB_FW_UPDATE_PROTECT = 0x6,
+ EC_SB_FW_UPDATE_MAX = 0x7,
+};
+
+#define SB_FW_UPDATE_CMD_WRITE_BLOCK_SIZE 32
+#define SB_FW_UPDATE_CMD_STATUS_SIZE 2
+#define SB_FW_UPDATE_CMD_INFO_SIZE 8
+
+struct ec_sb_fw_update_header {
+ uint16_t subcmd; /* enum ec_sb_fw_update_subcmd */
+ uint16_t fw_id; /* firmware id */
+} __ec_align4;
+
+struct ec_params_sb_fw_update {
+ struct ec_sb_fw_update_header hdr;
+ union {
+ /* EC_SB_FW_UPDATE_PREPARE = 0x0 */
+ /* EC_SB_FW_UPDATE_INFO = 0x1 */
+ /* EC_SB_FW_UPDATE_BEGIN = 0x2 */
+ /* EC_SB_FW_UPDATE_END = 0x4 */
+ /* EC_SB_FW_UPDATE_STATUS = 0x5 */
+ /* EC_SB_FW_UPDATE_PROTECT = 0x6 */
+ /* Those have no args */
+
+ /* EC_SB_FW_UPDATE_WRITE = 0x3 */
+ struct __ec_align4 {
+ uint8_t data[SB_FW_UPDATE_CMD_WRITE_BLOCK_SIZE];
+ } write;
+ };
+} __ec_align4;
+
+struct ec_response_sb_fw_update {
+ union {
+ /* EC_SB_FW_UPDATE_INFO = 0x1 */
+ struct __ec_align1 {
+ uint8_t data[SB_FW_UPDATE_CMD_INFO_SIZE];
+ } info;
+
+ /* EC_SB_FW_UPDATE_STATUS = 0x5 */
+ struct __ec_align1 {
+ uint8_t data[SB_FW_UPDATE_CMD_STATUS_SIZE];
+ } status;
+ };
+} __ec_align1;
+
+/*
+ * Entering Verified Boot Mode Command
+ * Default mode is VBOOT_MODE_NORMAL if EC did not receive this command.
+ * Valid Modes are: normal, developer, and recovery.
+ */
+#define EC_CMD_ENTERING_MODE 0x00B6
+
+struct ec_params_entering_mode {
+ int vboot_mode;
+} __ec_align4;
+
+#define VBOOT_MODE_NORMAL 0
+#define VBOOT_MODE_DEVELOPER 1
+#define VBOOT_MODE_RECOVERY 2
+
+/*****************************************************************************/
+/*
+ * I2C passthru protection command: Protects I2C tunnels against access on
+ * certain addresses (board-specific).
+ */
+#define EC_CMD_I2C_PASSTHRU_PROTECT 0x00B7
+
+enum ec_i2c_passthru_protect_subcmd {
+ EC_CMD_I2C_PASSTHRU_PROTECT_STATUS = 0x0,
+ EC_CMD_I2C_PASSTHRU_PROTECT_ENABLE = 0x1,
+};
+
+struct ec_params_i2c_passthru_protect {
+ uint8_t subcmd;
+ uint8_t port; /* I2C port number */
+} __ec_align1;
+
+struct ec_response_i2c_passthru_protect {
+ uint8_t status; /* Status flags (0: unlocked, 1: locked) */
+} __ec_align1;
+
+
+/*****************************************************************************/
+/*
+ * HDMI CEC commands
+ *
+ * These commands are for sending and receiving message via HDMI CEC
+ */
+
+#define MAX_CEC_MSG_LEN 16
+
+/* CEC message from the AP to be written on the CEC bus */
+#define EC_CMD_CEC_WRITE_MSG 0x00B8
+
+/**
+ * struct ec_params_cec_write - Message to write to the CEC bus
+ * @msg: message content to write to the CEC bus
+ */
+struct ec_params_cec_write {
+ uint8_t msg[MAX_CEC_MSG_LEN];
+} __ec_align1;
+
+/* Set various CEC parameters */
+#define EC_CMD_CEC_SET 0x00BA
+
+/**
+ * struct ec_params_cec_set - CEC parameters set
+ * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
+ * @val: in case cmd is CEC_CMD_ENABLE, this field can be 0 to disable CEC
+ * or 1 to enable CEC functionality, in case cmd is
+ * CEC_CMD_LOGICAL_ADDRESS, this field encodes the requested logical
+ * address between 0 and 15 or 0xff to unregister
+ */
+struct ec_params_cec_set {
+ uint8_t cmd; /* enum cec_command */
+ uint8_t val;
+} __ec_align1;
+
+/* Read various CEC parameters */
+#define EC_CMD_CEC_GET 0x00BB
+
+/**
+ * struct ec_params_cec_get - CEC parameters get
+ * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
+ */
+struct ec_params_cec_get {
+ uint8_t cmd; /* enum cec_command */
+} __ec_align1;
+
+/**
+ * struct ec_response_cec_get - CEC parameters get response
+ * @val: in case cmd was CEC_CMD_ENABLE, this field will 0 if CEC is
+ * disabled or 1 if CEC functionality is enabled,
+ * in case cmd was CEC_CMD_LOGICAL_ADDRESS, this will encode the
+ * configured logical address between 0 and 15 or 0xff if unregistered
+ */
+struct ec_response_cec_get {
+ uint8_t val;
+} __ec_align1;
+
+/* CEC parameters command */
+enum cec_command {
+ /* CEC reading, writing and events enable */
+ CEC_CMD_ENABLE,
+ /* CEC logical address */
+ CEC_CMD_LOGICAL_ADDRESS,
+};
+
+/* Events from CEC to AP */
+enum mkbp_cec_event {
+ /* Outgoing message was acknowledged by a follower */
+ EC_MKBP_CEC_SEND_OK = BIT(0),
+ /* Outgoing message was not acknowledged */
+ EC_MKBP_CEC_SEND_FAILED = BIT(1),
+};
+
+/*****************************************************************************/
+
/* Commands for I2S recording on audio codec. */
#define EC_CMD_CODEC_I2S 0x00BC
+#define EC_WOV_I2S_SAMPLE_RATE 48000
enum ec_codec_i2s_subcmd {
EC_CODEC_SET_SAMPLE_DEPTH = 0x0,
@@ -2892,6 +4481,7 @@ enum ec_codec_i2s_subcmd {
EC_CODEC_I2S_SET_CONFIG = 0x4,
EC_CODEC_I2S_SET_TDM_CONFIG = 0x5,
EC_CODEC_I2S_SET_BCLK = 0x6,
+ EC_CODEC_I2S_SUBCMD_COUNT = 0x7,
};
enum ec_sample_depth_value {
@@ -2908,10 +4498,23 @@ enum ec_i2s_config {
EC_DAI_FMT_PCM_TDM = 5,
};
-struct ec_param_codec_i2s {
- /*
- * enum ec_codec_i2s_subcmd
- */
+/*
+ * For subcommand EC_CODEC_GET_GAIN.
+ */
+struct __ec_align1 ec_codec_i2s_gain {
+ uint8_t left;
+ uint8_t right;
+};
+
+struct __ec_todo_unpacked ec_param_codec_i2s_tdm {
+ int16_t ch0_delay; /* 0 to 496 */
+ int16_t ch1_delay; /* -1 to 496 */
+ uint8_t adjacent_to_ch0;
+ uint8_t adjacent_to_ch1;
+};
+
+struct __ec_todo_packed ec_param_codec_i2s {
+ /* enum ec_codec_i2s_subcmd */
uint8_t cmd;
union {
/*
@@ -2924,10 +4527,7 @@ struct ec_param_codec_i2s {
* EC_CODEC_SET_GAIN
* Value should be 0~43 for both channels.
*/
- struct ec_param_codec_i2s_set_gain {
- uint8_t left;
- uint8_t right;
- } __packed gain;
+ struct ec_codec_i2s_gain gain;
/*
* EC_CODEC_I2S_ENABLE
@@ -2936,7 +4536,7 @@ struct ec_param_codec_i2s {
uint8_t i2s_enable;
/*
- * EC_CODEC_I2S_SET_COFNIG
+ * EC_CODEC_I2S_SET_CONFIG
* Value should be one of ec_i2s_config.
*/
uint8_t i2s_config;
@@ -2945,33 +4545,15 @@ struct ec_param_codec_i2s {
* EC_CODEC_I2S_SET_TDM_CONFIG
* Value should be one of ec_i2s_config.
*/
- struct ec_param_codec_i2s_tdm {
- /*
- * 0 to 496
- */
- int16_t ch0_delay;
- /*
- * -1 to 496
- */
- int16_t ch1_delay;
- uint8_t adjacent_to_ch0;
- uint8_t adjacent_to_ch1;
- } __packed tdm_param;
+ struct ec_param_codec_i2s_tdm tdm_param;
/*
* EC_CODEC_I2S_SET_BCLK
*/
uint32_t bclk;
};
-} __packed;
+};
-/*
- * For subcommand EC_CODEC_GET_GAIN.
- */
-struct ec_response_codec_gain {
- uint8_t left;
- uint8_t right;
-} __packed;
/*****************************************************************************/
/* System commands */
@@ -2980,27 +4562,29 @@ struct ec_response_codec_gain {
* TODO(crosbug.com/p/23747): This is a confusing name, since it doesn't
* necessarily reboot the EC. Rename to "image" or something similar?
*/
-#define EC_CMD_REBOOT_EC 0xd2
+#define EC_CMD_REBOOT_EC 0x00D2
/* Command */
enum ec_reboot_cmd {
EC_REBOOT_CANCEL = 0, /* Cancel a pending reboot */
EC_REBOOT_JUMP_RO = 1, /* Jump to RO without rebooting */
- EC_REBOOT_JUMP_RW = 2, /* Jump to RW without rebooting */
+ EC_REBOOT_JUMP_RW = 2, /* Jump to active RW without rebooting */
/* (command 3 was jump to RW-B) */
EC_REBOOT_COLD = 4, /* Cold-reboot */
EC_REBOOT_DISABLE_JUMP = 5, /* Disable jump until next reboot */
- EC_REBOOT_HIBERNATE = 6 /* Hibernate EC */
+ EC_REBOOT_HIBERNATE = 6, /* Hibernate EC */
+ EC_REBOOT_HIBERNATE_CLEAR_AP_OFF = 7, /* and clears AP_OFF flag */
};
/* Flags for ec_params_reboot_ec.reboot_flags */
-#define EC_REBOOT_FLAG_RESERVED0 (1 << 0) /* Was recovery request */
-#define EC_REBOOT_FLAG_ON_AP_SHUTDOWN (1 << 1) /* Reboot after AP shutdown */
+#define EC_REBOOT_FLAG_RESERVED0 BIT(0) /* Was recovery request */
+#define EC_REBOOT_FLAG_ON_AP_SHUTDOWN BIT(1) /* Reboot after AP shutdown */
+#define EC_REBOOT_FLAG_SWITCH_RW_SLOT BIT(2) /* Switch RW slot */
struct ec_params_reboot_ec {
uint8_t cmd; /* enum ec_reboot_cmd */
uint8_t flags; /* See EC_REBOOT_FLAG_* */
-} __packed;
+} __ec_align1;
/*
* Get information on last EC panic.
@@ -3008,196 +4592,7 @@ struct ec_params_reboot_ec {
* Returns variable-length platform-dependent panic information. See panic.h
* for details.
*/
-#define EC_CMD_GET_PANIC_INFO 0xd3
-
-/*****************************************************************************/
-/*
- * ACPI commands
- *
- * These are valid ONLY on the ACPI command/data port.
- */
-
-/*
- * ACPI Read Embedded Controller
- *
- * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
- *
- * Use the following sequence:
- *
- * - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD
- * - Wait for EC_LPC_CMDR_PENDING bit to clear
- * - Write address to EC_LPC_ADDR_ACPI_DATA
- * - Wait for EC_LPC_CMDR_DATA bit to set
- * - Read value from EC_LPC_ADDR_ACPI_DATA
- */
-#define EC_CMD_ACPI_READ 0x80
-
-/*
- * ACPI Write Embedded Controller
- *
- * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
- *
- * Use the following sequence:
- *
- * - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD
- * - Wait for EC_LPC_CMDR_PENDING bit to clear
- * - Write address to EC_LPC_ADDR_ACPI_DATA
- * - Wait for EC_LPC_CMDR_PENDING bit to clear
- * - Write value to EC_LPC_ADDR_ACPI_DATA
- */
-#define EC_CMD_ACPI_WRITE 0x81
-
-/*
- * ACPI Query Embedded Controller
- *
- * This clears the lowest-order bit in the currently pending host events, and
- * sets the result code to the 1-based index of the bit (event 0x00000001 = 1,
- * event 0x80000000 = 32), or 0 if no event was pending.
- */
-#define EC_CMD_ACPI_QUERY_EVENT 0x84
-
-/* Valid addresses in ACPI memory space, for read/write commands */
-
-/* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */
-#define EC_ACPI_MEM_VERSION 0x00
-/*
- * Test location; writing value here updates test compliment byte to (0xff -
- * value).
- */
-#define EC_ACPI_MEM_TEST 0x01
-/* Test compliment; writes here are ignored. */
-#define EC_ACPI_MEM_TEST_COMPLIMENT 0x02
-
-/* Keyboard backlight brightness percent (0 - 100) */
-#define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03
-/* DPTF Target Fan Duty (0-100, 0xff for auto/none) */
-#define EC_ACPI_MEM_FAN_DUTY 0x04
-
-/*
- * DPTF temp thresholds. Any of the EC's temp sensors can have up to two
- * independent thresholds attached to them. The current value of the ID
- * register determines which sensor is affected by the THRESHOLD and COMMIT
- * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme
- * as the memory-mapped sensors. The COMMIT register applies those settings.
- *
- * The spec does not mandate any way to read back the threshold settings
- * themselves, but when a threshold is crossed the AP needs a way to determine
- * which sensor(s) are responsible. Each reading of the ID register clears and
- * returns one sensor ID that has crossed one of its threshold (in either
- * direction) since the last read. A value of 0xFF means "no new thresholds
- * have tripped". Setting or enabling the thresholds for a sensor will clear
- * the unread event count for that sensor.
- */
-#define EC_ACPI_MEM_TEMP_ID 0x05
-#define EC_ACPI_MEM_TEMP_THRESHOLD 0x06
-#define EC_ACPI_MEM_TEMP_COMMIT 0x07
-/*
- * Here are the bits for the COMMIT register:
- * bit 0 selects the threshold index for the chosen sensor (0/1)
- * bit 1 enables/disables the selected threshold (0 = off, 1 = on)
- * Each write to the commit register affects one threshold.
- */
-#define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK (1 << 0)
-#define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK (1 << 1)
-/*
- * Example:
- *
- * Set the thresholds for sensor 2 to 50 C and 60 C:
- * write 2 to [0x05] -- select temp sensor 2
- * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET
- * write 0x2 to [0x07] -- enable threshold 0 with this value
- * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET
- * write 0x3 to [0x07] -- enable threshold 1 with this value
- *
- * Disable the 60 C threshold, leaving the 50 C threshold unchanged:
- * write 2 to [0x05] -- select temp sensor 2
- * write 0x1 to [0x07] -- disable threshold 1
- */
-
-/* DPTF battery charging current limit */
-#define EC_ACPI_MEM_CHARGING_LIMIT 0x08
-
-/* Charging limit is specified in 64 mA steps */
-#define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64
-/* Value to disable DPTF battery charging limit */
-#define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff
-
-/* Current version of ACPI memory address space */
-#define EC_ACPI_MEM_VERSION_CURRENT 1
-
-
-/*****************************************************************************/
-/*
- * HDMI CEC commands
- *
- * These commands are for sending and receiving message via HDMI CEC
- */
-#define EC_MAX_CEC_MSG_LEN 16
-
-/* CEC message from the AP to be written on the CEC bus */
-#define EC_CMD_CEC_WRITE_MSG 0x00B8
-
-/**
- * struct ec_params_cec_write - Message to write to the CEC bus
- * @msg: message content to write to the CEC bus
- */
-struct ec_params_cec_write {
- uint8_t msg[EC_MAX_CEC_MSG_LEN];
-} __packed;
-
-/* Set various CEC parameters */
-#define EC_CMD_CEC_SET 0x00BA
-
-/**
- * struct ec_params_cec_set - CEC parameters set
- * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
- * @val: in case cmd is CEC_CMD_ENABLE, this field can be 0 to disable CEC
- * or 1 to enable CEC functionality, in case cmd is CEC_CMD_LOGICAL_ADDRESS,
- * this field encodes the requested logical address between 0 and 15
- * or 0xff to unregister
- */
-struct ec_params_cec_set {
- uint8_t cmd; /* enum cec_command */
- uint8_t val;
-} __packed;
-
-/* Read various CEC parameters */
-#define EC_CMD_CEC_GET 0x00BB
-
-/**
- * struct ec_params_cec_get - CEC parameters get
- * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
- */
-struct ec_params_cec_get {
- uint8_t cmd; /* enum cec_command */
-} __packed;
-
-/**
- * struct ec_response_cec_get - CEC parameters get response
- * @val: in case cmd was CEC_CMD_ENABLE, this field will 0 if CEC is
- * disabled or 1 if CEC functionality is enabled,
- * in case cmd was CEC_CMD_LOGICAL_ADDRESS, this will encode the
- * configured logical address between 0 and 15 or 0xff if unregistered
- */
-struct ec_response_cec_get {
- uint8_t val;
-} __packed;
-
-/* CEC parameters command */
-enum ec_cec_command {
- /* CEC reading, writing and events enable */
- CEC_CMD_ENABLE,
- /* CEC logical address */
- CEC_CMD_LOGICAL_ADDRESS,
-};
-
-/* Events from CEC to AP */
-enum mkbp_cec_event {
- /* Outgoing message was acknowledged by a follower */
- EC_MKBP_CEC_SEND_OK = BIT(0),
- /* Outgoing message was not acknowledged */
- EC_MKBP_CEC_SEND_FAILED = BIT(1),
-};
+#define EC_CMD_GET_PANIC_INFO 0x00D3
/*****************************************************************************/
/*
@@ -3216,7 +4611,7 @@ enum mkbp_cec_event {
*
* Use EC_CMD_REBOOT_EC to reboot the EC more politely.
*/
-#define EC_CMD_REBOOT 0xd1 /* Think "die" */
+#define EC_CMD_REBOOT 0x00D1 /* Think "die" */
/*
* Resend last response (not supported on LPC).
@@ -3225,7 +4620,7 @@ enum mkbp_cec_event {
* there was no previous command, or the previous command's response was too
* big to save.
*/
-#define EC_CMD_RESEND_RESPONSE 0xdb
+#define EC_CMD_RESEND_RESPONSE 0x00DB
/*
* This header byte on a command indicate version 0. Any header byte less
@@ -3237,9 +4632,7 @@ enum mkbp_cec_event {
*
* The old EC interface must not use commands 0xdc or higher.
*/
-#define EC_CMD_VERSION0 0xdc
-
-#endif /* !__ACPI__ */
+#define EC_CMD_VERSION0 0x00DC
/*****************************************************************************/
/*
@@ -3249,21 +4642,56 @@ enum mkbp_cec_event {
*/
/* EC to PD MCU exchange status command */
-#define EC_CMD_PD_EXCHANGE_STATUS 0x100
+#define EC_CMD_PD_EXCHANGE_STATUS 0x0100
+#define EC_VER_PD_EXCHANGE_STATUS 2
+
+enum pd_charge_state {
+ PD_CHARGE_NO_CHANGE = 0, /* Don't change charge state */
+ PD_CHARGE_NONE, /* No charging allowed */
+ PD_CHARGE_5V, /* 5V charging only */
+ PD_CHARGE_MAX /* Charge at max voltage */
+};
/* Status of EC being sent to PD */
+#define EC_STATUS_HIBERNATING BIT(0)
+
struct ec_params_pd_status {
- int8_t batt_soc; /* battery state of charge */
-} __packed;
+ uint8_t status; /* EC status */
+ int8_t batt_soc; /* battery state of charge */
+ uint8_t charge_state; /* charging state (from enum pd_charge_state) */
+} __ec_align1;
/* Status of PD being sent back to EC */
+#define PD_STATUS_HOST_EVENT BIT(0) /* Forward host event to AP */
+#define PD_STATUS_IN_RW BIT(1) /* Running RW image */
+#define PD_STATUS_JUMPED_TO_IMAGE BIT(2) /* Current image was jumped to */
+#define PD_STATUS_TCPC_ALERT_0 BIT(3) /* Alert active in port 0 TCPC */
+#define PD_STATUS_TCPC_ALERT_1 BIT(4) /* Alert active in port 1 TCPC */
+#define PD_STATUS_TCPC_ALERT_2 BIT(5) /* Alert active in port 2 TCPC */
+#define PD_STATUS_TCPC_ALERT_3 BIT(6) /* Alert active in port 3 TCPC */
+#define PD_STATUS_EC_INT_ACTIVE (PD_STATUS_TCPC_ALERT_0 | \
+ PD_STATUS_TCPC_ALERT_1 | \
+ PD_STATUS_HOST_EVENT)
struct ec_response_pd_status {
- int8_t status; /* PD MCU status */
- uint32_t curr_lim_ma; /* input current limit */
-} __packed;
+ uint32_t curr_lim_ma; /* input current limit */
+ uint16_t status; /* PD MCU status */
+ int8_t active_charge_port; /* active charging port */
+} __ec_align_size1;
+
+/* AP to PD MCU host event status command, cleared on read */
+#define EC_CMD_PD_HOST_EVENT_STATUS 0x0104
+
+/* PD MCU host event status bits */
+#define PD_EVENT_UPDATE_DEVICE BIT(0)
+#define PD_EVENT_POWER_CHANGE BIT(1)
+#define PD_EVENT_IDENTITY_RECEIVED BIT(2)
+#define PD_EVENT_DATA_SWAP BIT(3)
+struct ec_response_host_event_status {
+ uint32_t status; /* PD MCU host event status */
+} __ec_align4;
/* Set USB type-C port role and muxes */
-#define EC_CMD_USB_PD_CONTROL 0x101
+#define EC_CMD_USB_PD_CONTROL 0x0101
enum usb_pd_control_role {
USB_PD_CTRL_ROLE_NO_CHANGE = 0,
@@ -3271,6 +4699,8 @@ enum usb_pd_control_role {
USB_PD_CTRL_ROLE_TOGGLE_OFF = 2,
USB_PD_CTRL_ROLE_FORCE_SINK = 3,
USB_PD_CTRL_ROLE_FORCE_SOURCE = 4,
+ USB_PD_CTRL_ROLE_FREEZE = 5,
+ USB_PD_CTRL_ROLE_COUNT
};
enum usb_pd_control_mux {
@@ -3280,6 +4710,7 @@ enum usb_pd_control_mux {
USB_PD_CTRL_MUX_DP = 3,
USB_PD_CTRL_MUX_DOCK = 4,
USB_PD_CTRL_MUX_AUTO = 5,
+ USB_PD_CTRL_MUX_COUNT
};
enum usb_pd_control_swap {
@@ -3295,11 +4726,11 @@ struct ec_params_usb_pd_control {
uint8_t role;
uint8_t mux;
uint8_t swap;
-} __packed;
+} __ec_align1;
-#define PD_CTRL_RESP_ENABLED_COMMS (1 << 0) /* Communication enabled */
-#define PD_CTRL_RESP_ENABLED_CONNECTED (1 << 1) /* Device connected */
-#define PD_CTRL_RESP_ENABLED_PD_CAPABLE (1 << 2) /* Partner is PD capable */
+#define PD_CTRL_RESP_ENABLED_COMMS BIT(0) /* Communication enabled */
+#define PD_CTRL_RESP_ENABLED_CONNECTED BIT(1) /* Device connected */
+#define PD_CTRL_RESP_ENABLED_PD_CAPABLE BIT(2) /* Partner is PD capable */
#define PD_CTRL_RESP_ROLE_POWER BIT(0) /* 0=SNK/1=SRC */
#define PD_CTRL_RESP_ROLE_DATA BIT(1) /* 0=UFP/1=DFP */
@@ -3309,28 +4740,54 @@ struct ec_params_usb_pd_control {
#define PD_CTRL_RESP_ROLE_USB_COMM BIT(5) /* Partner USB comm capable */
#define PD_CTRL_RESP_ROLE_EXT_POWERED BIT(6) /* Partner externally powerd */
+struct ec_response_usb_pd_control {
+ uint8_t enabled;
+ uint8_t role;
+ uint8_t polarity;
+ uint8_t state;
+} __ec_align1;
+
struct ec_response_usb_pd_control_v1 {
uint8_t enabled;
uint8_t role;
uint8_t polarity;
char state[32];
-} __packed;
+} __ec_align1;
-#define EC_CMD_USB_PD_PORTS 0x102
+/* Values representing usbc PD CC state */
+#define USBC_PD_CC_NONE 0 /* No accessory connected */
+#define USBC_PD_CC_NO_UFP 1 /* No UFP accessory connected */
+#define USBC_PD_CC_AUDIO_ACC 2 /* Audio accessory connected */
+#define USBC_PD_CC_DEBUG_ACC 3 /* Debug accessory connected */
+#define USBC_PD_CC_UFP_ATTACHED 4 /* UFP attached to usbc */
+#define USBC_PD_CC_DFP_ATTACHED 5 /* DPF attached to usbc */
+
+struct ec_response_usb_pd_control_v2 {
+ uint8_t enabled;
+ uint8_t role;
+ uint8_t polarity;
+ char state[32];
+ uint8_t cc_state; /* USBC_PD_CC_*Encoded cc state */
+ uint8_t dp_mode; /* Current DP pin mode (MODE_DP_PIN_[A-E]) */
+ /* CL:1500994 Current cable type */
+ uint8_t reserved_cable_type;
+} __ec_align1;
+
+#define EC_CMD_USB_PD_PORTS 0x0102
/* Maximum number of PD ports on a device, num_ports will be <= this */
#define EC_USB_PD_MAX_PORTS 8
struct ec_response_usb_pd_ports {
uint8_t num_ports;
-} __packed;
+} __ec_align1;
-#define EC_CMD_USB_PD_POWER_INFO 0x103
+#define EC_CMD_USB_PD_POWER_INFO 0x0103
#define PD_POWER_CHARGING_PORT 0xff
struct ec_params_usb_pd_power_info {
uint8_t port;
-} __packed;
+} __ec_align1;
enum usb_chg_type {
USB_CHG_TYPE_NONE,
@@ -3343,6 +4800,7 @@ enum usb_chg_type {
USB_CHG_TYPE_OTHER,
USB_CHG_TYPE_VBUS,
USB_CHG_TYPE_UNKNOWN,
+ USB_CHG_TYPE_DEDICATED,
};
enum usb_power_roles {
USB_PD_PORT_POWER_DISCONNECTED,
@@ -3356,7 +4814,7 @@ struct usb_chg_measures {
uint16_t voltage_now;
uint16_t current_max;
uint16_t current_lim;
-} __packed;
+} __ec_align2;
struct ec_response_usb_pd_power_info {
uint8_t role;
@@ -3365,11 +4823,8 @@ struct ec_response_usb_pd_power_info {
uint8_t reserved1;
struct usb_chg_measures meas;
uint32_t max_power;
-} __packed;
+} __ec_align4;
-struct ec_params_usb_pd_info_request {
- uint8_t port;
-} __packed;
/*
* This command will return the number of USB PD charge port + the number
@@ -3379,7 +4834,47 @@ struct ec_params_usb_pd_info_request {
#define EC_CMD_CHARGE_PORT_COUNT 0x0105
struct ec_response_charge_port_count {
uint8_t port_count;
-} __packed;
+} __ec_align1;
+
+/* Write USB-PD device FW */
+#define EC_CMD_USB_PD_FW_UPDATE 0x0110
+
+enum usb_pd_fw_update_cmds {
+ USB_PD_FW_REBOOT,
+ USB_PD_FW_FLASH_ERASE,
+ USB_PD_FW_FLASH_WRITE,
+ USB_PD_FW_ERASE_SIG,
+};
+
+struct ec_params_usb_pd_fw_update {
+ uint16_t dev_id;
+ uint8_t cmd;
+ uint8_t port;
+ uint32_t size; /* Size to write in bytes */
+ /* Followed by data to write */
+} __ec_align4;
+
+/* Write USB-PD Accessory RW_HASH table entry */
+#define EC_CMD_USB_PD_RW_HASH_ENTRY 0x0111
+/* RW hash is first 20 bytes of SHA-256 of RW section */
+#define PD_RW_HASH_SIZE 20
+struct ec_params_usb_pd_rw_hash_entry {
+ uint16_t dev_id;
+ uint8_t dev_rw_hash[PD_RW_HASH_SIZE];
+ uint8_t reserved; /*
+ * For alignment of current_image
+ * TODO(rspangler) but it's not aligned!
+ * Should have been reserved[2].
+ */
+ uint32_t current_image; /* One of ec_current_image */
+} __ec_align1;
+
+/* Read USB-PD Accessory info */
+#define EC_CMD_USB_PD_DEV_INFO 0x0112
+
+struct ec_params_usb_pd_info_request {
+ uint8_t port;
+} __ec_align1;
/* Read USB-PD Device discovery info */
#define EC_CMD_USB_PD_DISCOVERY 0x0113
@@ -3387,7 +4882,7 @@ struct ec_params_usb_pd_discovery_entry {
uint16_t vid; /* USB-IF VID */
uint16_t pid; /* USB-IF PID */
uint8_t ptype; /* product type (hub,periph,cable,ama) */
-} __packed;
+} __ec_align_size1;
/* Override default charge behavior */
#define EC_CMD_PD_CHARGE_PORT_OVERRIDE 0x0114
@@ -3401,9 +4896,13 @@ enum usb_pd_override_ports {
struct ec_params_charge_port_override {
int16_t override_port; /* Override port# */
-} __packed;
+} __ec_align2;
-/* Read (and delete) one entry of PD event log */
+/*
+ * Read (and delete) one entry of PD event log.
+ * TODO(crbug.com/751742): Make this host command more generic to accommodate
+ * future non-PD logs that use the same internal EC event_log.
+ */
#define EC_CMD_PD_GET_LOG_ENTRY 0x0115
struct ec_response_pd_log {
@@ -3412,7 +4911,7 @@ struct ec_response_pd_log {
uint8_t size_port; /* [7:5] port number [4:0] payload size in bytes */
uint16_t data; /* type-defined data payload */
uint8_t payload[0]; /* optional additional data payload: 0..16 bytes */
-} __packed;
+} __ec_align4;
/* The timestamp is the microsecond counter shifted to get about a ms. */
#define PD_LOG_TIMESTAMP_SHIFT 10 /* 1 LSB = 1024us */
@@ -3478,35 +4977,698 @@ struct mcdp_version {
uint8_t major;
uint8_t minor;
uint16_t build;
-} __packed;
+} __ec_align4;
struct mcdp_info {
uint8_t family[2];
uint8_t chipid[2];
struct mcdp_version irom;
struct mcdp_version fw;
-} __packed;
+} __ec_align4;
/* struct mcdp_info field decoding */
#define MCDP_CHIPID(chipid) ((chipid[0] << 8) | chipid[1])
#define MCDP_FAMILY(family) ((family[0] << 8) | family[1])
+/* Get/Set USB-PD Alternate mode info */
+#define EC_CMD_USB_PD_GET_AMODE 0x0116
+struct ec_params_usb_pd_get_mode_request {
+ uint16_t svid_idx; /* SVID index to get */
+ uint8_t port; /* port */
+} __ec_align_size1;
+
+struct ec_params_usb_pd_get_mode_response {
+ uint16_t svid; /* SVID */
+ uint16_t opos; /* Object Position */
+ uint32_t vdo[6]; /* Mode VDOs */
+} __ec_align4;
+
+#define EC_CMD_USB_PD_SET_AMODE 0x0117
+
+enum pd_mode_cmd {
+ PD_EXIT_MODE = 0,
+ PD_ENTER_MODE = 1,
+ /* Not a command. Do NOT remove. */
+ PD_MODE_CMD_COUNT,
+};
+
+struct ec_params_usb_pd_set_mode_request {
+ uint32_t cmd; /* enum pd_mode_cmd */
+ uint16_t svid; /* SVID to set */
+ uint8_t opos; /* Object Position */
+ uint8_t port; /* port */
+} __ec_align4;
+
+/* Ask the PD MCU to record a log of a requested type */
+#define EC_CMD_PD_WRITE_LOG_ENTRY 0x0118
+
+struct ec_params_pd_write_log_entry {
+ uint8_t type; /* event type : see PD_EVENT_xx above */
+ uint8_t port; /* port#, or 0 for events unrelated to a given port */
+} __ec_align1;
+
+
+/* Control USB-PD chip */
+#define EC_CMD_PD_CONTROL 0x0119
+
+enum ec_pd_control_cmd {
+ PD_SUSPEND = 0, /* Suspend the PD chip (EC: stop talking to PD) */
+ PD_RESUME, /* Resume the PD chip (EC: start talking to PD) */
+ PD_RESET, /* Force reset the PD chip */
+ PD_CONTROL_DISABLE, /* Disable further calls to this command */
+ PD_CHIP_ON, /* Power on the PD chip */
+};
+
+struct ec_params_pd_control {
+ uint8_t chip; /* chip id */
+ uint8_t subcmd;
+} __ec_align1;
+
/* Get info about USB-C SS muxes */
-#define EC_CMD_USB_PD_MUX_INFO 0x11a
+#define EC_CMD_USB_PD_MUX_INFO 0x011A
struct ec_params_usb_pd_mux_info {
uint8_t port; /* USB-C port number */
-} __packed;
+} __ec_align1;
/* Flags representing mux state */
-#define USB_PD_MUX_USB_ENABLED (1 << 0)
-#define USB_PD_MUX_DP_ENABLED (1 << 1)
-#define USB_PD_MUX_POLARITY_INVERTED (1 << 2)
-#define USB_PD_MUX_HPD_IRQ (1 << 3)
+#define USB_PD_MUX_USB_ENABLED BIT(0) /* USB connected */
+#define USB_PD_MUX_DP_ENABLED BIT(1) /* DP connected */
+#define USB_PD_MUX_POLARITY_INVERTED BIT(2) /* CC line Polarity inverted */
+#define USB_PD_MUX_HPD_IRQ BIT(3) /* HPD IRQ is asserted */
+#define USB_PD_MUX_HPD_LVL BIT(4) /* HPD level is asserted */
struct ec_response_usb_pd_mux_info {
uint8_t flags; /* USB_PD_MUX_*-encoded USB mux state */
-} __packed;
+} __ec_align1;
+
+#define EC_CMD_PD_CHIP_INFO 0x011B
+
+struct ec_params_pd_chip_info {
+ uint8_t port; /* USB-C port number */
+ uint8_t renew; /* Force renewal */
+} __ec_align1;
+
+struct ec_response_pd_chip_info {
+ uint16_t vendor_id;
+ uint16_t product_id;
+ uint16_t device_id;
+ union {
+ uint8_t fw_version_string[8];
+ uint64_t fw_version_number;
+ };
+} __ec_align2;
+
+struct ec_response_pd_chip_info_v1 {
+ uint16_t vendor_id;
+ uint16_t product_id;
+ uint16_t device_id;
+ union {
+ uint8_t fw_version_string[8];
+ uint64_t fw_version_number;
+ };
+ union {
+ uint8_t min_req_fw_version_string[8];
+ uint64_t min_req_fw_version_number;
+ };
+} __ec_align2;
+
+/* Run RW signature verification and get status */
+#define EC_CMD_RWSIG_CHECK_STATUS 0x011C
+
+struct ec_response_rwsig_check_status {
+ uint32_t status;
+} __ec_align4;
+
+/* For controlling RWSIG task */
+#define EC_CMD_RWSIG_ACTION 0x011D
+
+enum rwsig_action {
+ RWSIG_ACTION_ABORT = 0, /* Abort RWSIG and prevent jumping */
+ RWSIG_ACTION_CONTINUE = 1, /* Jump to RW immediately */
+};
+
+struct ec_params_rwsig_action {
+ uint32_t action;
+} __ec_align4;
+
+/* Run verification on a slot */
+#define EC_CMD_EFS_VERIFY 0x011E
+
+struct ec_params_efs_verify {
+ uint8_t region; /* enum ec_flash_region */
+} __ec_align1;
+
+/*
+ * Retrieve info from Cros Board Info store. Response is based on the data
+ * type. Integers return a uint32. Strings return a string, using the response
+ * size to determine how big it is.
+ */
+#define EC_CMD_GET_CROS_BOARD_INFO 0x011F
+/*
+ * Write info into Cros Board Info on EEPROM. Write fails if the board has
+ * hardware write-protect enabled.
+ */
+#define EC_CMD_SET_CROS_BOARD_INFO 0x0120
+
+enum cbi_data_tag {
+ CBI_TAG_BOARD_VERSION = 0, /* uint32_t or smaller */
+ CBI_TAG_OEM_ID = 1, /* uint32_t or smaller */
+ CBI_TAG_SKU_ID = 2, /* uint32_t or smaller */
+ CBI_TAG_DRAM_PART_NUM = 3, /* variable length ascii, nul terminated. */
+ CBI_TAG_OEM_NAME = 4, /* variable length ascii, nul terminated. */
+ CBI_TAG_MODEL_ID = 5, /* uint32_t or smaller */
+ CBI_TAG_COUNT,
+};
+
+/*
+ * Flags to control read operation
+ *
+ * RELOAD: Invalidate cache and read data from EEPROM. Useful to verify
+ * write was successful without reboot.
+ */
+#define CBI_GET_RELOAD BIT(0)
+
+struct ec_params_get_cbi {
+ uint32_t tag; /* enum cbi_data_tag */
+ uint32_t flag; /* CBI_GET_* */
+} __ec_align4;
+
+/*
+ * Flags to control write behavior.
+ *
+ * NO_SYNC: Makes EC update data in RAM but skip writing to EEPROM. It's
+ * useful when writing multiple fields in a row.
+ * INIT: Need to be set when creating a new CBI from scratch. All fields
+ * will be initialized to zero first.
+ */
+#define CBI_SET_NO_SYNC BIT(0)
+#define CBI_SET_INIT BIT(1)
+
+struct ec_params_set_cbi {
+ uint32_t tag; /* enum cbi_data_tag */
+ uint32_t flag; /* CBI_SET_* */
+ uint32_t size; /* Data size */
+ uint8_t data[]; /* For string and raw data */
+} __ec_align1;
+
+/*
+ * Information about resets of the AP by the EC and the EC's own uptime.
+ */
+#define EC_CMD_GET_UPTIME_INFO 0x0121
+
+struct ec_response_uptime_info {
+ /*
+ * Number of milliseconds since the last EC boot. Sysjump resets
+ * typically do not restart the EC's time_since_boot epoch.
+ *
+ * WARNING: The EC's sense of time is much less accurate than the AP's
+ * sense of time, in both phase and frequency. This timebase is similar
+ * to CLOCK_MONOTONIC_RAW, but with 1% or more frequency error.
+ */
+ uint32_t time_since_ec_boot_ms;
+
+ /*
+ * Number of times the AP was reset by the EC since the last EC boot.
+ * Note that the AP may be held in reset by the EC during the initial
+ * boot sequence, such that the very first AP boot may count as more
+ * than one here.
+ */
+ uint32_t ap_resets_since_ec_boot;
+
+ /*
+ * The set of flags which describe the EC's most recent reset. See
+ * include/system.h RESET_FLAG_* for details.
+ */
+ uint32_t ec_reset_flags;
+
+ /* Empty log entries have both the cause and timestamp set to zero. */
+ struct ap_reset_log_entry {
+ /*
+ * See include/chipset.h: enum chipset_{reset,shutdown}_reason
+ * for details.
+ */
+ uint16_t reset_cause;
+
+ /* Reserved for protocol growth. */
+ uint16_t reserved;
+
+ /*
+ * The time of the reset's assertion, in milliseconds since the
+ * last EC boot, in the same epoch as time_since_ec_boot_ms.
+ * Set to zero if the log entry is empty.
+ */
+ uint32_t reset_time_ms;
+ } recent_ap_reset[4];
+} __ec_align4;
+
+/*
+ * Add entropy to the device secret (stored in the rollback region).
+ *
+ * Depending on the chip, the operation may take a long time (e.g. to erase
+ * flash), so the commands are asynchronous.
+ */
+#define EC_CMD_ADD_ENTROPY 0x0122
+
+enum add_entropy_action {
+ /* Add entropy to the current secret. */
+ ADD_ENTROPY_ASYNC = 0,
+ /*
+ * Add entropy, and also make sure that the previous secret is erased.
+ * (this can be implemented by adding entropy multiple times until
+ * all rolback blocks have been overwritten).
+ */
+ ADD_ENTROPY_RESET_ASYNC = 1,
+ /* Read back result from the previous operation. */
+ ADD_ENTROPY_GET_RESULT = 2,
+};
+
+struct ec_params_rollback_add_entropy {
+ uint8_t action;
+} __ec_align1;
+
+/*
+ * Perform a single read of a given ADC channel.
+ */
+#define EC_CMD_ADC_READ 0x0123
+
+struct ec_params_adc_read {
+ uint8_t adc_channel;
+} __ec_align1;
+
+struct ec_response_adc_read {
+ int32_t adc_value;
+} __ec_align4;
+
+/*
+ * Read back rollback info
+ */
+#define EC_CMD_ROLLBACK_INFO 0x0124
+
+struct ec_response_rollback_info {
+ int32_t id; /* Incrementing number to indicate which region to use. */
+ int32_t rollback_min_version;
+ int32_t rw_rollback_version;
+} __ec_align4;
+
+
+/* Issue AP reset */
+#define EC_CMD_AP_RESET 0x0125
+
+/*****************************************************************************/
+/* The command range 0x200-0x2FF is reserved for Rotor. */
+
+/*****************************************************************************/
+/*
+ * Reserve a range of host commands for the CR51 firmware.
+ */
+#define EC_CMD_CR51_BASE 0x0300
+#define EC_CMD_CR51_LAST 0x03FF
+
+/*****************************************************************************/
+/* Fingerprint MCU commands: range 0x0400-0x040x */
+
+/* Fingerprint SPI sensor passthru command: prototyping ONLY */
+#define EC_CMD_FP_PASSTHRU 0x0400
+
+#define EC_FP_FLAG_NOT_COMPLETE 0x1
+
+struct ec_params_fp_passthru {
+ uint16_t len; /* Number of bytes to write then read */
+ uint16_t flags; /* EC_FP_FLAG_xxx */
+ uint8_t data[]; /* Data to send */
+} __ec_align2;
+
+/* Configure the Fingerprint MCU behavior */
+#define EC_CMD_FP_MODE 0x0402
+
+/* Put the sensor in its lowest power mode */
+#define FP_MODE_DEEPSLEEP BIT(0)
+/* Wait to see a finger on the sensor */
+#define FP_MODE_FINGER_DOWN BIT(1)
+/* Poll until the finger has left the sensor */
+#define FP_MODE_FINGER_UP BIT(2)
+/* Capture the current finger image */
+#define FP_MODE_CAPTURE BIT(3)
+/* Finger enrollment session on-going */
+#define FP_MODE_ENROLL_SESSION BIT(4)
+/* Enroll the current finger image */
+#define FP_MODE_ENROLL_IMAGE BIT(5)
+/* Try to match the current finger image */
+#define FP_MODE_MATCH BIT(6)
+/* Reset and re-initialize the sensor. */
+#define FP_MODE_RESET_SENSOR BIT(7)
+/* special value: don't change anything just read back current mode */
+#define FP_MODE_DONT_CHANGE BIT(31)
+
+#define FP_VALID_MODES (FP_MODE_DEEPSLEEP | \
+ FP_MODE_FINGER_DOWN | \
+ FP_MODE_FINGER_UP | \
+ FP_MODE_CAPTURE | \
+ FP_MODE_ENROLL_SESSION | \
+ FP_MODE_ENROLL_IMAGE | \
+ FP_MODE_MATCH | \
+ FP_MODE_RESET_SENSOR | \
+ FP_MODE_DONT_CHANGE)
+
+/* Capture types defined in bits [30..28] */
+#define FP_MODE_CAPTURE_TYPE_SHIFT 28
+#define FP_MODE_CAPTURE_TYPE_MASK (0x7 << FP_MODE_CAPTURE_TYPE_SHIFT)
+/*
+ * This enum must remain ordered, if you add new values you must ensure that
+ * FP_CAPTURE_TYPE_MAX is still the last one.
+ */
+enum fp_capture_type {
+ /* Full blown vendor-defined capture (produces 'frame_size' bytes) */
+ FP_CAPTURE_VENDOR_FORMAT = 0,
+ /* Simple raw image capture (produces width x height x bpp bits) */
+ FP_CAPTURE_SIMPLE_IMAGE = 1,
+ /* Self test pattern (e.g. checkerboard) */
+ FP_CAPTURE_PATTERN0 = 2,
+ /* Self test pattern (e.g. inverted checkerboard) */
+ FP_CAPTURE_PATTERN1 = 3,
+ /* Capture for Quality test with fixed contrast */
+ FP_CAPTURE_QUALITY_TEST = 4,
+ /* Capture for pixel reset value test */
+ FP_CAPTURE_RESET_TEST = 5,
+ FP_CAPTURE_TYPE_MAX,
+};
+/* Extracts the capture type from the sensor 'mode' word */
+#define FP_CAPTURE_TYPE(mode) (((mode) & FP_MODE_CAPTURE_TYPE_MASK) \
+ >> FP_MODE_CAPTURE_TYPE_SHIFT)
+
+struct ec_params_fp_mode {
+ uint32_t mode; /* as defined by FP_MODE_ constants */
+} __ec_align4;
+
+struct ec_response_fp_mode {
+ uint32_t mode; /* as defined by FP_MODE_ constants */
+} __ec_align4;
+
+/* Retrieve Fingerprint sensor information */
+#define EC_CMD_FP_INFO 0x0403
+
+/* Number of dead pixels detected on the last maintenance */
+#define FP_ERROR_DEAD_PIXELS(errors) ((errors) & 0x3FF)
+/* Unknown number of dead pixels detected on the last maintenance */
+#define FP_ERROR_DEAD_PIXELS_UNKNOWN (0x3FF)
+/* No interrupt from the sensor */
+#define FP_ERROR_NO_IRQ BIT(12)
+/* SPI communication error */
+#define FP_ERROR_SPI_COMM BIT(13)
+/* Invalid sensor Hardware ID */
+#define FP_ERROR_BAD_HWID BIT(14)
+/* Sensor initialization failed */
+#define FP_ERROR_INIT_FAIL BIT(15)
+
+struct ec_response_fp_info_v0 {
+ /* Sensor identification */
+ uint32_t vendor_id;
+ uint32_t product_id;
+ uint32_t model_id;
+ uint32_t version;
+ /* Image frame characteristics */
+ uint32_t frame_size;
+ uint32_t pixel_format; /* using V4L2_PIX_FMT_ */
+ uint16_t width;
+ uint16_t height;
+ uint16_t bpp;
+ uint16_t errors; /* see FP_ERROR_ flags above */
+} __ec_align4;
+
+struct ec_response_fp_info {
+ /* Sensor identification */
+ uint32_t vendor_id;
+ uint32_t product_id;
+ uint32_t model_id;
+ uint32_t version;
+ /* Image frame characteristics */
+ uint32_t frame_size;
+ uint32_t pixel_format; /* using V4L2_PIX_FMT_ */
+ uint16_t width;
+ uint16_t height;
+ uint16_t bpp;
+ uint16_t errors; /* see FP_ERROR_ flags above */
+ /* Template/finger current information */
+ uint32_t template_size; /* max template size in bytes */
+ uint16_t template_max; /* maximum number of fingers/templates */
+ uint16_t template_valid; /* number of valid fingers/templates */
+ uint32_t template_dirty; /* bitmap of templates with MCU side changes */
+ uint32_t template_version; /* version of the template format */
+} __ec_align4;
+
+/* Get the last captured finger frame or a template content */
+#define EC_CMD_FP_FRAME 0x0404
+
+/* constants defining the 'offset' field which also contains the frame index */
+#define FP_FRAME_INDEX_SHIFT 28
+/* Frame buffer where the captured image is stored */
+#define FP_FRAME_INDEX_RAW_IMAGE 0
+/* First frame buffer holding a template */
+#define FP_FRAME_INDEX_TEMPLATE 1
+#define FP_FRAME_GET_BUFFER_INDEX(offset) ((offset) >> FP_FRAME_INDEX_SHIFT)
+#define FP_FRAME_OFFSET_MASK 0x0FFFFFFF
+
+/* Version of the format of the encrypted templates. */
+#define FP_TEMPLATE_FORMAT_VERSION 3
+
+/* Constants for encryption parameters */
+#define FP_CONTEXT_NONCE_BYTES 12
+#define FP_CONTEXT_USERID_WORDS (32 / sizeof(uint32_t))
+#define FP_CONTEXT_TAG_BYTES 16
+#define FP_CONTEXT_SALT_BYTES 16
+#define FP_CONTEXT_TPM_BYTES 32
+
+struct ec_fp_template_encryption_metadata {
+ /*
+ * Version of the structure format (N=3).
+ */
+ uint16_t struct_version;
+ /* Reserved bytes, set to 0. */
+ uint16_t reserved;
+ /*
+ * The salt is *only* ever used for key derivation. The nonce is unique,
+ * a different one is used for every message.
+ */
+ uint8_t nonce[FP_CONTEXT_NONCE_BYTES];
+ uint8_t salt[FP_CONTEXT_SALT_BYTES];
+ uint8_t tag[FP_CONTEXT_TAG_BYTES];
+};
+
+struct ec_params_fp_frame {
+ /*
+ * The offset contains the template index or FP_FRAME_INDEX_RAW_IMAGE
+ * in the high nibble, and the real offset within the frame in
+ * FP_FRAME_OFFSET_MASK.
+ */
+ uint32_t offset;
+ uint32_t size;
+} __ec_align4;
+
+/* Load a template into the MCU */
+#define EC_CMD_FP_TEMPLATE 0x0405
+
+/* Flag in the 'size' field indicating that the full template has been sent */
+#define FP_TEMPLATE_COMMIT 0x80000000
+
+struct ec_params_fp_template {
+ uint32_t offset;
+ uint32_t size;
+ uint8_t data[];
+} __ec_align4;
+
+/* Clear the current fingerprint user context and set a new one */
+#define EC_CMD_FP_CONTEXT 0x0406
+
+struct ec_params_fp_context {
+ uint32_t userid[FP_CONTEXT_USERID_WORDS];
+} __ec_align4;
+
+#define EC_CMD_FP_STATS 0x0407
+
+#define FPSTATS_CAPTURE_INV BIT(0)
+#define FPSTATS_MATCHING_INV BIT(1)
+
+struct ec_response_fp_stats {
+ uint32_t capture_time_us;
+ uint32_t matching_time_us;
+ uint32_t overall_time_us;
+ struct {
+ uint32_t lo;
+ uint32_t hi;
+ } overall_t0;
+ uint8_t timestamps_invalid;
+ int8_t template_matched;
+} __ec_align2;
+
+#define EC_CMD_FP_SEED 0x0408
+struct ec_params_fp_seed {
+ /*
+ * Version of the structure format (N=3).
+ */
+ uint16_t struct_version;
+ /* Reserved bytes, set to 0. */
+ uint16_t reserved;
+ /* Seed from the TPM. */
+ uint8_t seed[FP_CONTEXT_TPM_BYTES];
+} __ec_align4;
+
+/*****************************************************************************/
+/* Touchpad MCU commands: range 0x0500-0x05FF */
+
+/* Perform touchpad self test */
+#define EC_CMD_TP_SELF_TEST 0x0500
+
+/* Get number of frame types, and the size of each type */
+#define EC_CMD_TP_FRAME_INFO 0x0501
+
+struct ec_response_tp_frame_info {
+ uint32_t n_frames;
+ uint32_t frame_sizes[0];
+} __ec_align4;
+
+/* Create a snapshot of current frame readings */
+#define EC_CMD_TP_FRAME_SNAPSHOT 0x0502
+
+/* Read the frame */
+#define EC_CMD_TP_FRAME_GET 0x0503
+
+struct ec_params_tp_frame_get {
+ uint32_t frame_index;
+ uint32_t offset;
+ uint32_t size;
+} __ec_align4;
+
+/*****************************************************************************/
+/* EC-EC communication commands: range 0x0600-0x06FF */
+
+#define EC_COMM_TEXT_MAX 8
+
+/*
+ * Get battery static information, i.e. information that never changes, or
+ * very infrequently.
+ */
+#define EC_CMD_BATTERY_GET_STATIC 0x0600
+
+/**
+ * struct ec_params_battery_static_info - Battery static info parameters
+ * @index: Battery index.
+ */
+struct ec_params_battery_static_info {
+ uint8_t index;
+} __ec_align_size1;
+
+/**
+ * struct ec_response_battery_static_info - Battery static info response
+ * @design_capacity: Battery Design Capacity (mAh)
+ * @design_voltage: Battery Design Voltage (mV)
+ * @manufacturer: Battery Manufacturer String
+ * @model: Battery Model Number String
+ * @serial: Battery Serial Number String
+ * @type: Battery Type String
+ * @cycle_count: Battery Cycle Count
+ */
+struct ec_response_battery_static_info {
+ uint16_t design_capacity;
+ uint16_t design_voltage;
+ char manufacturer[EC_COMM_TEXT_MAX];
+ char model[EC_COMM_TEXT_MAX];
+ char serial[EC_COMM_TEXT_MAX];
+ char type[EC_COMM_TEXT_MAX];
+ /* TODO(crbug.com/795991): Consider moving to dynamic structure. */
+ uint32_t cycle_count;
+} __ec_align4;
+
+/*
+ * Get battery dynamic information, i.e. information that is likely to change
+ * every time it is read.
+ */
+#define EC_CMD_BATTERY_GET_DYNAMIC 0x0601
+
+/**
+ * struct ec_params_battery_dynamic_info - Battery dynamic info parameters
+ * @index: Battery index.
+ */
+struct ec_params_battery_dynamic_info {
+ uint8_t index;
+} __ec_align_size1;
+
+/**
+ * struct ec_response_battery_dynamic_info - Battery dynamic info response
+ * @actual_voltage: Battery voltage (mV)
+ * @actual_current: Battery current (mA); negative=discharging
+ * @remaining_capacity: Remaining capacity (mAh)
+ * @full_capacity: Capacity (mAh, might change occasionally)
+ * @flags: Flags, see EC_BATT_FLAG_*
+ * @desired_voltage: Charging voltage desired by battery (mV)
+ * @desired_current: Charging current desired by battery (mA)
+ */
+struct ec_response_battery_dynamic_info {
+ int16_t actual_voltage;
+ int16_t actual_current;
+ int16_t remaining_capacity;
+ int16_t full_capacity;
+ int16_t flags;
+ int16_t desired_voltage;
+ int16_t desired_current;
+} __ec_align2;
+
+/*
+ * Control charger chip. Used to control charger chip on the slave.
+ */
+#define EC_CMD_CHARGER_CONTROL 0x0602
+
+/**
+ * struct ec_params_charger_control - Charger control parameters
+ * @max_current: Charger current (mA). Positive to allow base to draw up to
+ * max_current and (possibly) charge battery, negative to request current
+ * from base (OTG).
+ * @otg_voltage: Voltage (mV) to use in OTG mode, ignored if max_current is
+ * >= 0.
+ * @allow_charging: Allow base battery charging (only makes sense if
+ * max_current > 0).
+ */
+struct ec_params_charger_control {
+ int16_t max_current;
+ uint16_t otg_voltage;
+ uint8_t allow_charging;
+} __ec_align_size1;
+
+/*****************************************************************************/
+/*
+ * Reserve a range of host commands for board-specific, experimental, or
+ * special purpose features. These can be (re)used without updating this file.
+ *
+ * CAUTION: Don't go nuts with this. Shipping products should document ALL
+ * their EC commands for easier development, testing, debugging, and support.
+ *
+ * All commands MUST be #defined to be 4-digit UPPER CASE hex values
+ * (e.g., 0x00AB, not 0xab) for CONFIG_HOSTCMD_SECTION_SORTED to work.
+ *
+ * In your experimental code, you may want to do something like this:
+ *
+ * #define EC_CMD_MAGIC_FOO 0x0000
+ * #define EC_CMD_MAGIC_BAR 0x0001
+ * #define EC_CMD_MAGIC_HEY 0x0002
+ *
+ * DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_FOO, magic_foo_handler,
+ * EC_VER_MASK(0);
+ *
+ * DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_BAR, magic_bar_handler,
+ * EC_VER_MASK(0);
+ *
+ * DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_HEY, magic_hey_handler,
+ * EC_VER_MASK(0);
+ */
+#define EC_CMD_BOARD_SPECIFIC_BASE 0x3E00
+#define EC_CMD_BOARD_SPECIFIC_LAST 0x3FFF
+
+/*
+ * Given the private host command offset, calculate the true private host
+ * command value.
+ */
+#define EC_PRIVATE_HOST_COMMAND_VALUE(command) \
+ (EC_CMD_BOARD_SPECIFIC_BASE + (command))
/*****************************************************************************/
/*
@@ -3546,4 +5708,6 @@ struct ec_response_usb_pd_mux_info {
#define EC_LPC_ADDR_OLD_PARAM EC_HOST_CMD_REGION1
#define EC_OLD_PARAM_SIZE EC_HOST_CMD_REGION_SIZE
+
+
#endif /* __CROS_EC_COMMANDS_H */
diff --git a/include/linux/mfd/lp87565.h b/include/linux/mfd/lp87565.h
index d0c91ba..9764476 100644
--- a/include/linux/mfd/lp87565.h
+++ b/include/linux/mfd/lp87565.h
@@ -17,6 +17,7 @@
enum lp87565_device_type {
LP87565_DEVICE_TYPE_UNKNOWN = 0,
+ LP87565_DEVICE_TYPE_LP87561_Q1,
LP87565_DEVICE_TYPE_LP87565_Q1,
};
@@ -249,6 +250,7 @@ enum LP87565_regulator_id {
LP87565_BUCK_3,
LP87565_BUCK_10,
LP87565_BUCK_23,
+ LP87565_BUCK_3210,
};
/**
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index d315659..2a9cd01 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -382,6 +382,7 @@ enum rk805_reg {
#define SWITCH1_EN BIT(5)
#define DEV_OFF_RST BIT(3)
#define DEV_OFF BIT(0)
+#define RTC_STOP BIT(0)
#define VB_LO_ACT BIT(4)
#define VB_LO_SEL_3500MV (7 << 0)
@@ -395,7 +396,179 @@ enum rk805_reg {
#define SHUTDOWN_FUN (0x2 << 2)
#define SLEEP_FUN (0x1 << 2)
#define RK8XX_ID_MSK 0xfff0
+#define PWM_MODE_MSK BIT(7)
#define FPWM_MODE BIT(7)
+#define AUTO_PWM_MODE 0
+
+enum rk817_reg_id {
+ RK817_ID_DCDC1 = 0,
+ RK817_ID_DCDC2,
+ RK817_ID_DCDC3,
+ RK817_ID_DCDC4,
+ RK817_ID_LDO1,
+ RK817_ID_LDO2,
+ RK817_ID_LDO3,
+ RK817_ID_LDO4,
+ RK817_ID_LDO5,
+ RK817_ID_LDO6,
+ RK817_ID_LDO7,
+ RK817_ID_LDO8,
+ RK817_ID_LDO9,
+ RK817_ID_BOOST,
+ RK817_ID_BOOST_OTG_SW,
+ RK817_NUM_REGULATORS
+};
+
+enum rk809_reg_id {
+ RK809_ID_DCDC5 = RK817_ID_BOOST,
+ RK809_ID_SW1,
+ RK809_ID_SW2,
+ RK809_NUM_REGULATORS
+};
+
+#define RK817_SECONDS_REG 0x00
+#define RK817_MINUTES_REG 0x01
+#define RK817_HOURS_REG 0x02
+#define RK817_DAYS_REG 0x03
+#define RK817_MONTHS_REG 0x04
+#define RK817_YEARS_REG 0x05
+#define RK817_WEEKS_REG 0x06
+#define RK817_ALARM_SECONDS_REG 0x07
+#define RK817_ALARM_MINUTES_REG 0x08
+#define RK817_ALARM_HOURS_REG 0x09
+#define RK817_ALARM_DAYS_REG 0x0a
+#define RK817_ALARM_MONTHS_REG 0x0b
+#define RK817_ALARM_YEARS_REG 0x0c
+#define RK817_RTC_CTRL_REG 0xd
+#define RK817_RTC_STATUS_REG 0xe
+#define RK817_RTC_INT_REG 0xf
+#define RK817_RTC_COMP_LSB_REG 0x10
+#define RK817_RTC_COMP_MSB_REG 0x11
+
+#define RK817_POWER_EN_REG(i) (0xb1 + (i))
+#define RK817_POWER_SLP_EN_REG(i) (0xb5 + (i))
+
+#define RK817_POWER_CONFIG (0xb9)
+
+#define RK817_BUCK_CONFIG_REG(i) (0xba + (i) * 3)
+
+#define RK817_BUCK1_ON_VSEL_REG 0xBB
+#define RK817_BUCK1_SLP_VSEL_REG 0xBC
+
+#define RK817_BUCK2_CONFIG_REG 0xBD
+#define RK817_BUCK2_ON_VSEL_REG 0xBE
+#define RK817_BUCK2_SLP_VSEL_REG 0xBF
+
+#define RK817_BUCK3_CONFIG_REG 0xC0
+#define RK817_BUCK3_ON_VSEL_REG 0xC1
+#define RK817_BUCK3_SLP_VSEL_REG 0xC2
+
+#define RK817_BUCK4_CONFIG_REG 0xC3
+#define RK817_BUCK4_ON_VSEL_REG 0xC4
+#define RK817_BUCK4_SLP_VSEL_REG 0xC5
+
+#define RK817_LDO_ON_VSEL_REG(idx) (0xcc + (idx) * 2)
+#define RK817_BOOST_OTG_CFG (0xde)
+
+#define RK817_ID_MSB 0xed
+#define RK817_ID_LSB 0xee
+
+#define RK817_SYS_STS 0xf0
+#define RK817_SYS_CFG(i) (0xf1 + (i))
+
+#define RK817_ON_SOURCE_REG 0xf5
+#define RK817_OFF_SOURCE_REG 0xf6
+
+/* INTERRUPT REGISTER */
+#define RK817_INT_STS_REG0 0xf8
+#define RK817_INT_STS_MSK_REG0 0xf9
+#define RK817_INT_STS_REG1 0xfa
+#define RK817_INT_STS_MSK_REG1 0xfb
+#define RK817_INT_STS_REG2 0xfc
+#define RK817_INT_STS_MSK_REG2 0xfd
+#define RK817_GPIO_INT_CFG 0xfe
+
+/* IRQ Definitions */
+#define RK817_IRQ_PWRON_FALL 0
+#define RK817_IRQ_PWRON_RISE 1
+#define RK817_IRQ_PWRON 2
+#define RK817_IRQ_PWMON_LP 3
+#define RK817_IRQ_HOTDIE 4
+#define RK817_IRQ_RTC_ALARM 5
+#define RK817_IRQ_RTC_PERIOD 6
+#define RK817_IRQ_VB_LO 7
+#define RK817_IRQ_PLUG_IN 8
+#define RK817_IRQ_PLUG_OUT 9
+#define RK817_IRQ_CHRG_TERM 10
+#define RK817_IRQ_CHRG_TIME 11
+#define RK817_IRQ_CHRG_TS 12
+#define RK817_IRQ_USB_OV 13
+#define RK817_IRQ_CHRG_IN_CLMP 14
+#define RK817_IRQ_BAT_DIS_ILIM 15
+#define RK817_IRQ_GATE_GPIO 16
+#define RK817_IRQ_TS_GPIO 17
+#define RK817_IRQ_CODEC_PD 18
+#define RK817_IRQ_CODEC_PO 19
+#define RK817_IRQ_CLASSD_MUTE_DONE 20
+#define RK817_IRQ_CLASSD_OCP 21
+#define RK817_IRQ_BAT_OVP 22
+#define RK817_IRQ_CHRG_BAT_HI 23
+#define RK817_IRQ_END (RK817_IRQ_CHRG_BAT_HI + 1)
+
+/*
+ * rtc_ctrl 0xd
+ * same as 808, except bit4
+ */
+#define RK817_RTC_CTRL_RSV4 BIT(4)
+
+/* power config 0xb9 */
+#define RK817_BUCK3_FB_RES_MSK BIT(6)
+#define RK817_BUCK3_FB_RES_INTER BIT(6)
+#define RK817_BUCK3_FB_RES_EXT 0
+
+/* buck config 0xba */
+#define RK817_RAMP_RATE_OFFSET 6
+#define RK817_RAMP_RATE_MASK (0x3 << RK817_RAMP_RATE_OFFSET)
+#define RK817_RAMP_RATE_3MV_PER_US (0x0 << RK817_RAMP_RATE_OFFSET)
+#define RK817_RAMP_RATE_6_3MV_PER_US (0x1 << RK817_RAMP_RATE_OFFSET)
+#define RK817_RAMP_RATE_12_5MV_PER_US (0x2 << RK817_RAMP_RATE_OFFSET)
+#define RK817_RAMP_RATE_25MV_PER_US (0x3 << RK817_RAMP_RATE_OFFSET)
+
+/* sys_cfg1 0xf2 */
+#define RK817_HOTDIE_TEMP_MSK (0x3 << 4)
+#define RK817_HOTDIE_85 (0x0 << 4)
+#define RK817_HOTDIE_95 (0x1 << 4)
+#define RK817_HOTDIE_105 (0x2 << 4)
+#define RK817_HOTDIE_115 (0x3 << 4)
+
+#define RK817_TSD_TEMP_MSK BIT(6)
+#define RK817_TSD_140 0
+#define RK817_TSD_160 BIT(6)
+
+#define RK817_CLK32KOUT2_EN BIT(7)
+
+/* sys_cfg3 0xf4 */
+#define RK817_SLPPIN_FUNC_MSK (0x3 << 3)
+#define SLPPIN_NULL_FUN (0x0 << 3)
+#define SLPPIN_SLP_FUN (0x1 << 3)
+#define SLPPIN_DN_FUN (0x2 << 3)
+#define SLPPIN_RST_FUN (0x3 << 3)
+
+#define RK817_RST_FUNC_MSK (0x3 << 6)
+#define RK817_RST_FUNC_SFT (6)
+#define RK817_RST_FUNC_CNT (3)
+#define RK817_RST_FUNC_DEV (0) /* reset the dev */
+#define RK817_RST_FUNC_REG (0x1 << 6) /* reset the reg only */
+
+#define RK817_SLPPOL_MSK BIT(5)
+#define RK817_SLPPOL_H BIT(5)
+#define RK817_SLPPOL_L (0)
+
+/* gpio&int 0xfe */
+#define RK817_INT_POL_MSK BIT(1)
+#define RK817_INT_POL_H BIT(1)
+#define RK817_INT_POL_L 0
+#define RK809_BUCK5_CONFIG(i) (RK817_BOOST_OTG_CFG + (i) * 1)
enum {
BUCK_ILMIN_50MA,
@@ -443,6 +616,8 @@ enum {
enum {
RK805_ID = 0x8050,
RK808_ID = 0x0000,
+ RK809_ID = 0x8090,
+ RK817_ID = 0x8170,
RK818_ID = 0x8181,
};
diff --git a/sound/soc/codecs/cros_ec_codec.c b/sound/soc/codecs/cros_ec_codec.c
index 99a3af8..87830ed 100644
--- a/sound/soc/codecs/cros_ec_codec.c
+++ b/sound/soc/codecs/cros_ec_codec.c
@@ -38,21 +38,21 @@ static const DECLARE_TLV_DB_SCALE(ec_mic_gain_tlv, 0, 100, 0);
static int ec_command_get_gain(struct snd_soc_component *component,
struct ec_param_codec_i2s *param,
- struct ec_response_codec_gain *resp)
+ struct ec_codec_i2s_gain *resp)
{
struct cros_ec_codec_data *codec_data =
snd_soc_component_get_drvdata(component);
struct cros_ec_device *ec_device = codec_data->ec_device;
u8 buffer[sizeof(struct cros_ec_command) +
max(sizeof(struct ec_param_codec_i2s),
- sizeof(struct ec_response_codec_gain))];
+ sizeof(struct ec_codec_i2s_gain))];
struct cros_ec_command *msg = (struct cros_ec_command *)&buffer;
int ret;
msg->version = 0;
msg->command = EC_CMD_CODEC_I2S;
msg->outsize = sizeof(struct ec_param_codec_i2s);
- msg->insize = sizeof(struct ec_response_codec_gain);
+ msg->insize = sizeof(struct ec_codec_i2s_gain);
memcpy(msg->data, param, msg->outsize);
@@ -226,7 +226,7 @@ static int get_ec_mic_gain(struct snd_soc_component *component,
u8 *left, u8 *right)
{
struct ec_param_codec_i2s param;
- struct ec_response_codec_gain resp;
+ struct ec_codec_i2s_gain resp;
int ret;
param.cmd = EC_CODEC_GET_GAIN;
