| /* SPDX-License-Identifier: GPL-2.0-or-later */ |
| /* |
| * include/linux/mmc/sdio.h |
| * |
| * Copyright 2006-2007 Pierre Ossman |
| */ |
| |
| #ifndef LINUX_MMC_SDIO_H |
| #define LINUX_MMC_SDIO_H |
| |
| /* SDIO commands type argument response */ |
| #define SD_IO_SEND_OP_COND 5 /* bcr [23:0] OCR R4 */ |
| #define SD_IO_RW_DIRECT 52 /* ac [31:0] See below R5 */ |
| #define SD_IO_RW_EXTENDED 53 /* adtc [31:0] See below R5 */ |
| |
| /* |
| * SD_IO_RW_DIRECT argument format: |
| * |
| * [31] R/W flag |
| * [30:28] Function number |
| * [27] RAW flag |
| * [25:9] Register address |
| * [7:0] Data |
| */ |
| |
| /* |
| * SD_IO_RW_EXTENDED argument format: |
| * |
| * [31] R/W flag |
| * [30:28] Function number |
| * [27] Block mode |
| * [26] Increment address |
| * [25:9] Register address |
| * [8:0] Byte/block count |
| */ |
| |
| #define R4_18V_PRESENT (1<<24) |
| #define R4_MEMORY_PRESENT (1 << 27) |
| |
| /* |
| SDIO status in R5 |
| Type |
| e : error bit |
| s : status bit |
| r : detected and set for the actual command response |
| x : detected and set during command execution. the host must poll |
| the card by sending status command in order to read these bits. |
| Clear condition |
| a : according to the card state |
| b : always related to the previous command. Reception of |
| a valid command will clear it (with a delay of one command) |
| c : clear by read |
| */ |
| |
| #define R5_COM_CRC_ERROR (1 << 15) /* er, b */ |
| #define R5_ILLEGAL_COMMAND (1 << 14) /* er, b */ |
| #define R5_ERROR (1 << 11) /* erx, c */ |
| #define R5_FUNCTION_NUMBER (1 << 9) /* er, c */ |
| #define R5_OUT_OF_RANGE (1 << 8) /* er, c */ |
| #define R5_STATUS(x) (x & 0xCB00) |
| #define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */ |
| |
| /* |
| * Card Common Control Registers (CCCR) |
| */ |
| |
| #define SDIO_CCCR_CCCR 0x00 |
| |
| #define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */ |
| #define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */ |
| #define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */ |
| #define SDIO_CCCR_REV_3_00 3 /* CCCR/FBR Version 3.00 */ |
| |
| #define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */ |
| #define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */ |
| #define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */ |
| #define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */ |
| #define SDIO_SDIO_REV_3_00 4 /* SDIO Spec Version 3.00 */ |
| |
| #define SDIO_CCCR_SD 0x01 |
| |
| #define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */ |
| #define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */ |
| #define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */ |
| #define SDIO_SD_REV_3_00 3 /* SD Physical Spec Version 3.00 */ |
| |
| #define SDIO_CCCR_IOEx 0x02 |
| #define SDIO_CCCR_IORx 0x03 |
| |
| #define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */ |
| #define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */ |
| |
| #define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */ |
| |
| #define SDIO_CCCR_IF 0x07 /* bus interface controls */ |
| |
| #define SDIO_BUS_WIDTH_MASK 0x03 /* data bus width setting */ |
| #define SDIO_BUS_WIDTH_1BIT 0x00 |
| #define SDIO_BUS_WIDTH_RESERVED 0x01 |
| #define SDIO_BUS_WIDTH_4BIT 0x02 |
| #define SDIO_BUS_ECSI 0x20 /* Enable continuous SPI interrupt */ |
| #define SDIO_BUS_SCSI 0x40 /* Support continuous SPI interrupt */ |
| |
| #define SDIO_BUS_ASYNC_INT 0x20 |
| |
| #define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */ |
| |
| #define SDIO_CCCR_CAPS 0x08 |
| |
| #define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */ |
| #define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */ |
| #define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */ |
| #define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */ |
| #define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */ |
| #define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */ |
| #define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */ |
| #define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */ |
| |
| #define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */ |
| |
| /* Following 4 regs are valid only if SBS is set */ |
| #define SDIO_CCCR_SUSPEND 0x0c |
| #define SDIO_CCCR_SELx 0x0d |
| #define SDIO_CCCR_EXECx 0x0e |
| #define SDIO_CCCR_READYx 0x0f |
| |
| #define SDIO_CCCR_BLKSIZE 0x10 |
| |
| #define SDIO_CCCR_POWER 0x12 |
| |
| #define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */ |
| #define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */ |
| |
| #define SDIO_CCCR_SPEED 0x13 |
| |
| #define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */ |
| #define SDIO_SPEED_BSS_SHIFT 1 |
| #define SDIO_SPEED_BSS_MASK (7<<SDIO_SPEED_BSS_SHIFT) |
| #define SDIO_SPEED_SDR12 (0<<SDIO_SPEED_BSS_SHIFT) |
| #define SDIO_SPEED_SDR25 (1<<SDIO_SPEED_BSS_SHIFT) |
| #define SDIO_SPEED_SDR50 (2<<SDIO_SPEED_BSS_SHIFT) |
| #define SDIO_SPEED_SDR104 (3<<SDIO_SPEED_BSS_SHIFT) |
| #define SDIO_SPEED_DDR50 (4<<SDIO_SPEED_BSS_SHIFT) |
| #define SDIO_SPEED_EHS SDIO_SPEED_SDR25 /* Enable High-Speed */ |
| |
| #define SDIO_CCCR_UHS 0x14 |
| #define SDIO_UHS_SDR50 0x01 |
| #define SDIO_UHS_SDR104 0x02 |
| #define SDIO_UHS_DDR50 0x04 |
| |
| #define SDIO_CCCR_DRIVE_STRENGTH 0x15 |
| #define SDIO_SDTx_MASK 0x07 |
| #define SDIO_DRIVE_SDTA (1<<0) |
| #define SDIO_DRIVE_SDTC (1<<1) |
| #define SDIO_DRIVE_SDTD (1<<2) |
| #define SDIO_DRIVE_DTSx_MASK 0x03 |
| #define SDIO_DRIVE_DTSx_SHIFT 4 |
| #define SDIO_DTSx_SET_TYPE_B (0 << SDIO_DRIVE_DTSx_SHIFT) |
| #define SDIO_DTSx_SET_TYPE_A (1 << SDIO_DRIVE_DTSx_SHIFT) |
| #define SDIO_DTSx_SET_TYPE_C (2 << SDIO_DRIVE_DTSx_SHIFT) |
| #define SDIO_DTSx_SET_TYPE_D (3 << SDIO_DRIVE_DTSx_SHIFT) |
| /* |
| * Function Basic Registers (FBR) |
| */ |
| |
| #define SDIO_FBR_BASE(f) ((f) * 0x100) /* base of function f's FBRs */ |
| |
| #define SDIO_FBR_STD_IF 0x00 |
| |
| #define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */ |
| #define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */ |
| |
| #define SDIO_FBR_STD_IF_EXT 0x01 |
| |
| #define SDIO_FBR_POWER 0x02 |
| |
| #define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */ |
| #define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */ |
| |
| #define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */ |
| |
| |
| #define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */ |
| |
| #define SDIO_FBR_CSA_DATA 0x0F |
| |
| #define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */ |
| |
| #endif /* LINUX_MMC_SDIO_H */ |