[PATCH] sky2: yukon-ec-u chipset initialization
Add more complete setup code for Yukon EC_U chipset.
Based on matching code in 8.31 code in SysKonnect vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index bfeba5b..ce135b8 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -232,7 +232,17 @@
if (hw->ports > 1)
reg1 |= PCI_Y2_PHY2_COMA;
}
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG3, 0);
+ pci_read_config_dword(hw->pdev, PCI_DEV_REG4, ®1);
+ reg1 &= P_ASPM_CONTROL_MSK;
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG4, reg1);
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG5, 0);
+ }
+
pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+
break;
case PCI_D3hot:
@@ -463,16 +473,31 @@
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+ /* apply fixes in PHY AFE */
+ gm_phy_write(hw, port, 22, 255);
+ /* increase differential signal amplitude in 10BASE-T */
+ gm_phy_write(hw, port, 24, 0xaa99);
+ gm_phy_write(hw, port, 23, 0x2011);
- if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
- /* turn on 100 Mbps LED (LED_LINK100) */
- ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+ /* fix for IEEE A/B Symmetry failure in 1000BASE-T */
+ gm_phy_write(hw, port, 24, 0xa204);
+ gm_phy_write(hw, port, 23, 0x2002);
+
+ /* set page register to 0 */
+ gm_phy_write(hw, port, 22, 0);
+ } else {
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+
+ if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
+ /* turn on 100 Mbps LED (LED_LINK100) */
+ ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+ }
+
+ if (ledover)
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+
}
-
- if (ledover)
- gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
-
/* Enable phy interrupt on auto-negotiation complete (or link up) */
if (sky2->autoneg == AUTONEG_ENABLE)
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
@@ -953,6 +978,12 @@
sky2->rx_put = sky2->rx_next = 0;
sky2_qset(hw, rxq);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+ /* MAC Rx RAM Read is controlled by hardware */
+ sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS);
+ }
+
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
rx_set_checksum(sky2);
@@ -1035,9 +1066,10 @@
RB_RST_SET);
sky2_qset(hw, txqaddr[port]);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U)
- sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
+ /* Set almost empty threshold */
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1)
+ sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
TX_RING_SIZE - 1);
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index fd12c28..d1c71f5 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -5,14 +5,22 @@
#define _SKY2_H
/* PCI config registers */
-#define PCI_DEV_REG1 0x40
-#define PCI_DEV_REG2 0x44
-#define PCI_DEV_STATUS 0x7c
-#define PCI_OS_PCI_X (1<<26)
+enum {
+ PCI_DEV_REG1 = 0x40,
+ PCI_DEV_REG2 = 0x44,
+ PCI_DEV_STATUS = 0x7c,
+ PCI_DEV_REG3 = 0x80,
+ PCI_DEV_REG4 = 0x84,
+ PCI_DEV_REG5 = 0x88,
+};
-#define PEX_LNK_STAT 0xf2
-#define PEX_UNC_ERR_STAT 0x104
-#define PEX_DEV_CTRL 0xe8
+enum {
+ PEX_DEV_CAP = 0xe4,
+ PEX_DEV_CTRL = 0xe8,
+ PEX_DEV_STA = 0xea,
+ PEX_LNK_STAT = 0xf2,
+ PEX_UNC_ERR_STAT= 0x104,
+};
/* Yukon-2 */
enum pci_dev_reg_1 {
@@ -37,6 +45,25 @@
PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
};
+/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */
+enum pci_dev_reg_4 {
+ /* (Link Training & Status State Machine) */
+ P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */
+ /* (Active State Power Management) */
+ P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */
+ P_ASPM_GPHY_LINK_DOWN = 1<<14, /* GPHY Link Down (A1 only) */
+ P_ASPM_INT_FIFO_EMPTY = 1<<13, /* Internal FIFO Empty (A1 only) */
+ P_ASPM_CLKRUN_REQUEST = 1<<12, /* CLKRUN Request (A1 only) */
+
+ P_ASPM_FORCE_CLKREQ_ENA = 1<<4, /* Force CLKREQ Enable (A1b only) */
+ P_ASPM_CLKREQ_PAD_CTL = 1<<3, /* CLKREQ PAD Control (A1 only) */
+ P_ASPM_A1_MODE_SELECT = 1<<2, /* A1 Mode Select (A1 only) */
+ P_CLK_GATE_PEX_UNIT_ENA = 1<<1, /* Enable Gate PEX Unit Clock */
+ P_CLK_GATE_ROOT_COR_ENA = 1<<0, /* Enable Gate Root Core Clock */
+ P_ASPM_CONTROL_MSK = P_FORCE_ASPM_REQUEST | P_ASPM_GPHY_LINK_DOWN
+ | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
+};
+
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
@@ -507,6 +534,16 @@
};
#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
+/* Q_F 32 bit Flag Register */
+enum {
+ F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */
+ F_EMPTY = 1<<27, /* Tx FIFO: empty flag */
+ F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */
+ F_WM_REACHED = 1<<25, /* Watermark reached */
+ F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */
+ F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */
+ F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */
+};
/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
enum {
@@ -909,10 +946,12 @@
PHY_BCOM_ID1_C0 = 0x6044,
PHY_BCOM_ID1_C5 = 0x6047,
- PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
+ PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
- PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
- PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
+ PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
+ PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
+ PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE (PHY 88E3082 Rev.A1) */
+ PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU (PHY 88E1149 Rev.B2?) */
};
/* Advertisement register bits */
