pata_via: Use cable_detect method
We end up shifting a few bits of logic around in this driver but the
basic change is the same.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 946ade0..96b7179 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -62,7 +62,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_via"
-#define DRV_VERSION "0.2.1"
+#define DRV_VERSION "0.3.1"
/*
* The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
@@ -135,16 +135,23 @@
*/
static int via_cable_detect(struct ata_port *ap) {
+ const struct via_isa_bridge *config = ap->host->private_data;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 ata66;
+ /* Early chips are 40 wire */
+ if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
+ return ATA_CBL_PATA40;
+ /* UDMA 66 chips have only drive side logic */
+ else if((config->flags & VIA_UDMA) < VIA_UDMA_100)
+ return ATA_CBL_PATA_UNK;
+ /* UDMA 100 or later */
pci_read_config_dword(pdev, 0x50, &ata66);
/* Check both the drive cable reporting bits, we might not have
two drives */
if (ata66 & (0x10100000 >> (16 * ap->port_no)))
return ATA_CBL_PATA80;
- else
- return ATA_CBL_PATA40;
+ return ATA_CBL_PATA40;
}
static int via_pre_reset(struct ata_port *ap)
@@ -156,22 +163,10 @@
{ 0x40, 1, 0x02, 0x02 },
{ 0x40, 1, 0x01, 0x01 }
};
-
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-
if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no]))
return -ENOENT;
}
-
- if ((config->flags & VIA_UDMA) >= VIA_UDMA_100)
- ap->cbl = via_cable_detect(ap);
- /* The UDMA66 series has no cable detect so do drive side detect */
- else if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
- ap->cbl = ATA_CBL_PATA40;
- else
- ap->cbl = ATA_CBL_PATA_UNK;
-
-
return ata_std_prereset(ap);
}
@@ -327,6 +322,7 @@
.thaw = ata_bmdma_thaw,
.error_handler = via_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = via_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -362,6 +358,7 @@
.thaw = ata_bmdma_thaw,
.error_handler = via_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = via_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
