blob: 58fc8a6cebc7d2e5d3f0e8104294b4b6275ed230 [file] [log] [blame]
* Rockchip rk3399 DMC (Dynamic Memory Controller) device
Required properties:
- compatible: Must be "rockchip,rk3399-dmc".
- devfreq-events: Node to get DDR loading, Refer to
Documentation/devicetree/bindings/devfreq/event/
rockchip-dfi.txt
- clocks: Phandles for clock specified in "clock-names" property
- clock-names : The name of clock used by the DFI, must be
"pclk_ddr_mon";
- operating-points-v2: Refer to Documentation/devicetree/bindings/opp/opp-v2.yaml
for details.
- center-supply: DMC supply node.
- status: Marks the node enabled/disabled.
- rockchip,pmu: Phandle to the syscon managing the "PMU general register
files".
Optional properties:
- interrupts: The CPU interrupt number. The interrupt specifier
format depends on the interrupt controller.
It should be a DCF interrupt. When DDR DVFS finishes
a DCF interrupt is triggered.
- rockchip,pmu: Phandle to the syscon managing the "PMU general register
files".
Following properties relate to DDR timing:
- rockchip,dram_speed_bin : Value reference include/dt-bindings/clock/rk3399-ddr.h,
it selects the DDR3 cl-trp-trcd type. It must be
set according to "Speed Bin" in DDR3 datasheet,
DO NOT use a smaller "Speed Bin" than specified
for the DDR3 being used.
- rockchip,pd_idle : Configure the PD_IDLE value. Defines the
power-down idle period in which memories are
placed into power-down mode if bus is idle
for PD_IDLE DFI clock cycles.
- rockchip,sr_idle : Configure the SR_IDLE value. Defines the
self-refresh idle period in which memories are
placed into self-refresh mode if bus is idle
for SR_IDLE * 1024 DFI clock cycles (DFI
clocks freq is half of DRAM clock), default
value is "0".
- rockchip,sr_mc_gate_idle : Defines the memory self-refresh and controller
clock gating idle period. Memories are placed
into self-refresh mode and memory controller
clock arg gating started if bus is idle for
sr_mc_gate_idle*1024 DFI clock cycles.
- rockchip,srpd_lite_idle : Defines the self-refresh power down idle
period in which memories are placed into
self-refresh power down mode if bus is idle
for srpd_lite_idle * 1024 DFI clock cycles.
This parameter is for LPDDR4 only.
- rockchip,standby_idle : Defines the standby idle period in which
memories are placed into self-refresh mode.
The controller, pi, PHY and DRAM clock will
be gated if bus is idle for standby_idle * DFI
clock cycles.
- rockchip,dram_dll_dis_freq : Defines the DDR3 DLL bypass frequency in MHz.
When DDR frequency is less than DRAM_DLL_DISB_FREQ,
DDR3 DLL will be bypassed. Note: if DLL was bypassed,
the odt will also stop working.
- rockchip,phy_dll_dis_freq : Defines the PHY dll bypass frequency in
MHz (Mega Hz). When DDR frequency is less than
DRAM_DLL_DISB_FREQ, PHY DLL will be bypassed.
Note: PHY DLL and PHY ODT are independent.
- rockchip,ddr3_odt_dis_freq : When the DRAM type is DDR3, this parameter defines
the ODT disable frequency in MHz (Mega Hz).
when the DDR frequency is less then ddr3_odt_dis_freq,
the ODT on the DRAM side and controller side are
both disabled.
- rockchip,ddr3_drv : When the DRAM type is DDR3, this parameter defines
the DRAM side driver strength in ohms. Default
value is 40.
- rockchip,ddr3_odt : When the DRAM type is DDR3, this parameter defines
the DRAM side ODT strength in ohms. Default value
is 120.
- rockchip,phy_ddr3_ca_drv : When the DRAM type is DDR3, this parameter defines
the phy side CA line (incluing command line,
address line and clock line) driver strength.
Default value is 40.
- rockchip,phy_ddr3_dq_drv : When the DRAM type is DDR3, this parameter defines
the PHY side DQ line (including DQS/DQ/DM line)
driver strength. Default value is 40.
- rockchip,phy_ddr3_odt : When the DRAM type is DDR3, this parameter defines
the PHY side ODT strength. Default value is 240.
- rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines
then ODT disable frequency in MHz (Mega Hz).
When DDR frequency is less then ddr3_odt_dis_freq,
the ODT on the DRAM side and controller side are
both disabled.
- rockchip,lpddr3_drv : When the DRAM type is LPDDR3, this parameter defines
the DRAM side driver strength in ohms. Default
value is 34.
- rockchip,lpddr3_odt : When the DRAM type is LPDDR3, this parameter defines
the DRAM side ODT strength in ohms. Default value
is 240.
- rockchip,phy_lpddr3_ca_drv : When the DRAM type is LPDDR3, this parameter defines
the PHY side CA line (including command line,
address line and clock line) driver strength.
Default value is 40.
- rockchip,phy_lpddr3_dq_drv : When the DRAM type is LPDDR3, this parameter defines
the PHY side DQ line (including DQS/DQ/DM line)
driver strength. Default value is 40.
- rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define
the phy side odt strength, default value is 240.
- rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter
defines the ODT disable frequency in
MHz (Mega Hz). When the DDR frequency is less then
ddr3_odt_dis_freq, the ODT on the DRAM side and
controller side are both disabled.
- rockchip,lpddr4_drv : When the DRAM type is LPDDR4, this parameter defines
the DRAM side driver strength in ohms. Default
value is 60.
- rockchip,lpddr4_dq_odt : When the DRAM type is LPDDR4, this parameter defines
the DRAM side ODT on DQS/DQ line strength in ohms.
Default value is 40.
- rockchip,lpddr4_ca_odt : When the DRAM type is LPDDR4, this parameter defines
the DRAM side ODT on CA line strength in ohms.
Default value is 40.
- rockchip,phy_lpddr4_ca_drv : When the DRAM type is LPDDR4, this parameter defines
the PHY side CA line (including command address
line) driver strength. Default value is 40.
- rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines
the PHY side clock line and CS line driver
strength. Default value is 80.
- rockchip,phy_lpddr4_dq_drv : When the DRAM type is LPDDR4, this parameter defines
the PHY side DQ line (including DQS/DQ/DM line)
driver strength. Default value is 80.
- rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines
the PHY side ODT strength. Default value is 60.
Example:
dmc_opp_table: dmc_opp_table {
compatible = "operating-points-v2";
opp00 {
opp-hz = /bits/ 64 <300000000>;
opp-microvolt = <900000>;
};
opp01 {
opp-hz = /bits/ 64 <666000000>;
opp-microvolt = <900000>;
};
};
dmc: dmc {
compatible = "rockchip,rk3399-dmc";
devfreq-events = <&dfi>;
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_DDRC>;
clock-names = "dmc_clk";
operating-points-v2 = <&dmc_opp_table>;
center-supply = <&ppvar_centerlogic>;
upthreshold = <15>;
downdifferential = <10>;
rockchip,ddr3_speed_bin = <21>;
rockchip,pd_idle = <0x40>;
rockchip,sr_idle = <0x2>;
rockchip,sr_mc_gate_idle = <0x3>;
rockchip,srpd_lite_idle = <0x4>;
rockchip,standby_idle = <0x2000>;
rockchip,dram_dll_dis_freq = <300>;
rockchip,phy_dll_dis_freq = <125>;
rockchip,auto_pd_dis_freq = <666>;
rockchip,ddr3_odt_dis_freq = <333>;
rockchip,ddr3_drv = <40>;
rockchip,ddr3_odt = <120>;
rockchip,phy_ddr3_ca_drv = <40>;
rockchip,phy_ddr3_dq_drv = <40>;
rockchip,phy_ddr3_odt = <240>;
rockchip,lpddr3_odt_dis_freq = <333>;
rockchip,lpddr3_drv = <34>;
rockchip,lpddr3_odt = <240>;
rockchip,phy_lpddr3_ca_drv = <40>;
rockchip,phy_lpddr3_dq_drv = <40>;
rockchip,phy_lpddr3_odt = <240>;
rockchip,lpddr4_odt_dis_freq = <333>;
rockchip,lpddr4_drv = <60>;
rockchip,lpddr4_dq_odt = <40>;
rockchip,lpddr4_ca_odt = <40>;
rockchip,phy_lpddr4_ca_drv = <40>;
rockchip,phy_lpddr4_ck_cs_drv = <80>;
rockchip,phy_lpddr4_dq_drv = <80>;
rockchip,phy_lpddr4_odt = <60>;
};