| # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/regulator/nxp,pca9450-regulator.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: NXP PCA9450A/B/C Power Management Integrated Circuit regulators |
| |
| maintainers: |
| - Robin Gong <yibin.gong@nxp.com> |
| |
| description: | |
| Regulator nodes should be named to BUCK_<number> and LDO_<number>. The |
| definition for each of these nodes is defined using the standard |
| binding for regulators at |
| Documentation/devicetree/bindings/regulator/regulator.txt. |
| Datasheet is available at |
| https://www.nxp.com/docs/en/data-sheet/PCA9450DS.pdf |
| |
| #The valid names for PCA9450 regulator nodes are: |
| #BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, |
| #LDO1, LDO2, LDO3, LDO4, LDO5 |
| #Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C. |
| |
| properties: |
| compatible: |
| enum: |
| - nxp,pca9450a |
| - nxp,pca9450b |
| - nxp,pca9450c |
| |
| reg: |
| maxItems: 1 |
| |
| interrupts: |
| maxItems: 1 |
| |
| regulators: |
| type: object |
| description: | |
| list of regulators provided by this controller |
| |
| patternProperties: |
| "^LDO[1-5]$": |
| type: object |
| $ref: regulator.yaml# |
| description: |
| Properties for single LDO regulator. |
| |
| properties: |
| regulator-name: |
| pattern: "^LDO[1-5]$" |
| description: |
| should be "LDO1", ..., "LDO5" |
| |
| unevaluatedProperties: false |
| |
| "^BUCK[1-6]$": |
| type: object |
| $ref: regulator.yaml# |
| description: |
| Properties for single BUCK regulator. |
| |
| properties: |
| regulator-name: |
| pattern: "^BUCK[1-6]$" |
| description: |
| should be "BUCK1", ..., "BUCK6" |
| |
| nxp,dvs-run-voltage: |
| $ref: "/schemas/types.yaml#/definitions/uint32" |
| minimum: 600000 |
| maximum: 2187500 |
| description: |
| PMIC default "RUN" state voltage in uV. Only Buck1~3 have such |
| dvs(dynamic voltage scaling) property. |
| |
| nxp,dvs-standby-voltage: |
| $ref: "/schemas/types.yaml#/definitions/uint32" |
| minimum: 600000 |
| maximum: 2187500 |
| description: |
| PMIC default "STANDBY" state voltage in uV. Only Buck1~3 have such |
| dvs(dynamic voltage scaling) property. |
| |
| unevaluatedProperties: false |
| |
| additionalProperties: false |
| |
| sd-vsel-gpios: |
| description: GPIO that is used to switch LDO5 between being configured by |
| LDO5CTRL_L or LDO5CTRL_H register. Use this if the SD_VSEL signal is |
| connected to a host GPIO. |
| |
| required: |
| - compatible |
| - reg |
| - interrupts |
| - regulators |
| |
| additionalProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pmic: pmic@25 { |
| compatible = "nxp,pca9450b"; |
| reg = <0x25>; |
| pinctrl-0 = <&pinctrl_pmic>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| |
| regulators { |
| buck1: BUCK1 { |
| regulator-name = "BUCK1"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <2187500>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <3125>; |
| }; |
| buck2: BUCK2 { |
| regulator-name = "BUCK2"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <2187500>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <3125>; |
| nxp,dvs-run-voltage = <950000>; |
| nxp,dvs-standby-voltage = <850000>; |
| }; |
| buck4: BUCK4 { |
| regulator-name = "BUCK4"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| buck5: BUCK5 { |
| regulator-name = "BUCK5"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| buck6: BUCK6 { |
| regulator-name = "BUCK6"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1: LDO1 { |
| regulator-name = "LDO1"; |
| regulator-min-microvolt = <1600000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| ldo2: LDO2 { |
| regulator-name = "LDO2"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1150000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| ldo3: LDO3 { |
| regulator-name = "LDO3"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| ldo4: LDO4 { |
| regulator-name = "LDO4"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| ldo5: LDO5 { |
| regulator-name = "LDO5"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
