| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Google Cheza board device tree source |
| * |
| * Copyright 2018 Google LLC. |
| */ |
| |
| /dts-v1/; |
| |
| #include "sdm845-cheza.dtsi" |
| |
| / { |
| model = "Google Cheza (rev2)"; |
| compatible = "google,cheza-rev2", "qcom,sdm845"; |
| |
| /* |
| * FIXED REGULATORS (not in sdm845-cheza.dtsi) - parents above children |
| */ |
| |
| /* |
| * NOTE: Technically pp3500_a is not the exact same signal as |
| * pp3500_a_vbob (there's a load switch between them and the EC can |
| * control pp3500_a via "en_pp3300_a"), but from the AP's point of |
| * view they are the same. |
| */ |
| pp3500_a: |
| pp3500_a_vbob: pp3500-a-vbob-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_bob"; |
| |
| /* |
| * Comes on automatically when pp5000_ldo comes on, which |
| * comes on automatically when ppvar_sys comes on |
| */ |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3500000>; |
| regulator-max-microvolt = <3500000>; |
| |
| vin-supply = <&ppvar_sys>; |
| }; |
| |
| pp3300_dx_edp: pp3300-dx-edp-regulator { |
| /* Yes, it's really 3.5 despite the name of the signal */ |
| regulator-min-microvolt = <3500000>; |
| regulator-max-microvolt = <3500000>; |
| |
| vin-supply = <&pp3500_a>; |
| }; |
| }; |
| |
| /* FIXED REGULATOR OVERRIDES (modifications to sdm845-cheza.dtsi) */ |
| |
| /* |
| * L19 and L28 technically go to 3.3V, but most boards have old AOP firmware |
| * that limits them to 3.0, and trying to run at 3.3V with that old firmware |
| * prevents the system from booting. |
| */ |
| &src_pp3000_l19a { |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| }; |
| |
| &src_pp3300_l22a { |
| /delete-property/regulator-boot-on; |
| /delete-property/regulator-always-on; |
| }; |
| |
| &src_pp3300_l28a { |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| }; |
| |
| &src_vreg_bob { |
| regulator-min-microvolt = <3500000>; |
| regulator-max-microvolt = <3500000>; |
| vin-supply = <&pp3500_a_vbob>; |
| }; |
| |
| /* |
| * NON-REGULATOR OVERRIDES |
| * (modifications to sdm845-cheza.dtsi) - alphabetized by dtsi label |
| */ |
| |
| /* PINCTRL - board-specific pinctrl */ |
| |
| &tlmm { |
| gpio-line-names = "AP_SPI_FP_MISO", |
| "AP_SPI_FP_MOSI", |
| "AP_SPI_FP_CLK", |
| "AP_SPI_FP_CS_L", |
| "UART_AP_TX_DBG_RX", |
| "UART_DBG_TX_AP_RX", |
| "BRIJ_SUSPEND", |
| "FP_RST_L", |
| "FCAM_EN", |
| "", |
| "EDP_BRIJ_IRQ", |
| "EC_IN_RW_ODL", |
| "", |
| "RCAM_MCLK", |
| "FCAM_MCLK", |
| "", |
| "RCAM_EN", |
| "CCI0_SDA", |
| "CCI0_SCL", |
| "CCI1_SDA", |
| "CCI1_SCL", |
| "FCAM_RST_L", |
| "FPMCU_BOOT0", |
| "PEN_RST_L", |
| "PEN_IRQ_L", |
| "FPMCU_SEL_OD", |
| "RCAM_VSYNC", |
| "ESIM_MISO", |
| "ESIM_MOSI", |
| "ESIM_CLK", |
| "ESIM_CS_L", |
| "AP_PEN_1V8_SDA", |
| "AP_PEN_1V8_SCL", |
| "AP_TS_I2C_SDA", |
| "AP_TS_I2C_SCL", |
| "RCAM_RST_L", |
| "", |
| "AP_EDP_BKLTEN", |
| "AP_BRD_ID1", |
| "BOOT_CONFIG_4", |
| "AMP_IRQ_L", |
| "EDP_BRIJ_I2C_SDA", |
| "EDP_BRIJ_I2C_SCL", |
| "EN_PP3300_DX_EDP", |
| "SD_CD_ODL", |
| "BT_UART_RTS", |
| "BT_UART_CTS", |
| "BT_UART_RXD", |
| "BT_UART_TXD", |
| "AMP_I2C_SDA", |
| "AMP_I2C_SCL", |
| "AP_BRD_ID3", |
| "", |
| "AP_EC_SPI_CLK", |
| "AP_EC_SPI_CS_L", |
| "AP_EC_SPI_MISO", |
| "AP_EC_SPI_MOSI", |
| "FORCED_USB_BOOT", |
| "AMP_BCLK", |
| "AMP_LRCLK", |
| "AMP_DOUT", |
| "AMP_DIN", |
| "AP_BRD_ID2", |
| "PEN_PDCT_L", |
| "HP_MCLK", |
| "HP_BCLK", |
| "HP_LRCLK", |
| "HP_DOUT", |
| "HP_DIN", |
| "", |
| "", |
| "", |
| "", |
| "BT_SLIMBUS_DATA", |
| "BT_SLIMBUS_CLK", |
| "AMP_RESET_L", |
| "", |
| "FCAM_VSYNC", |
| "", |
| "AP_SKU_ID1", |
| "EC_WOV_BCLK", |
| "EC_WOV_LRCLK", |
| "EC_WOV_DOUT", |
| "", |
| "", |
| "AP_H1_SPI_MISO", |
| "AP_H1_SPI_MOSI", |
| "AP_H1_SPI_CLK", |
| "AP_H1_SPI_CS_L", |
| "", |
| "AP_SPI_CS0_L", |
| "AP_SPI_MOSI", |
| "AP_SPI_MISO", |
| "", |
| "", |
| "AP_SPI_CLK", |
| "", |
| "RFFE6_CLK", |
| "RFFE6_DATA", |
| "BOOT_CONFIG_1", |
| "BOOT_CONFIG_2", |
| "BOOT_CONFIG_0", |
| "EDP_BRIJ_EN", |
| "", |
| "USB_HS_TX_EN", |
| "UIM2_DATA", |
| "UIM2_CLK", |
| "UIM2_RST", |
| "UIM2_PRESENT", |
| "UIM1_DATA", |
| "UIM1_CLK", |
| "UIM1_RST", |
| "", |
| "AP_SKU_ID2", |
| "SDM_GRFC_8", |
| "SDM_GRFC_9", |
| "AP_RST_REQ", |
| "HP_IRQ", |
| "TS_RESET_L", |
| "PEN_EJECT_ODL", |
| "HUB_RST_L", |
| "FP_TO_AP_IRQ", |
| "AP_EC_INT_L", |
| "", |
| "", |
| "TS_INT_L", |
| "AP_SUSPEND_L", |
| "SDM_GRFC_3", |
| "", |
| "H1_AP_INT_ODL", |
| "QLINK_REQ", |
| "QLINK_EN", |
| "SDM_GRFC_2", |
| "BOOT_CONFIG_3", |
| "WMSS_RESET_L", |
| "SDM_GRFC_0", |
| "SDM_GRFC_1", |
| "RFFE3_DATA", |
| "RFFE3_CLK", |
| "RFFE4_DATA", |
| "RFFE4_CLK", |
| "RFFE5_DATA", |
| "RFFE5_CLK", |
| "GNSS_EN", |
| "WCI2_LTE_COEX_RXD", |
| "WCI2_LTE_COEX_TXD", |
| "AP_RAM_ID1", |
| "AP_RAM_ID2", |
| "RFFE1_DATA", |
| "RFFE1_CLK"; |
| }; |
