mmc: mmci: Add qcom dml support to the driver.
On Qualcomm APQ8064 SOCs, SD card controller has an additional glue
called DML (Data Mover Local/Lite) to assist dma transfers.
This hardware needs to be setup before any dma transfer is requested.
DML itself is not a DMA engine, its just a gule between the SD card
controller and dma controller.
Most of this code has been ported from qualcomm's 3.4 kernel.
This patch adds the code necessary to intialize the hardware and setup
before doing any dma transfers.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index e4d4707..a7b3af9 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -43,6 +43,7 @@
#include <asm/sizes.h>
#include "mmci.h"
+#include "mmci_qcom_dml.h"
#define DRIVER_NAME "mmci-pl18x"
@@ -74,6 +75,7 @@
* @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
* @explicit_mclk_control: enable explicit mclk control in driver.
* @qcom_fifo: enables qcom specific fifo pio read logic.
+ * @qcom_dml: enables qcom specific dma glue for dma transfers.
* @reversed_irq_handling: handle data irq before cmd irq.
*/
struct variant_data {
@@ -98,6 +100,7 @@
bool pwrreg_nopower;
bool explicit_mclk_control;
bool qcom_fifo;
+ bool qcom_dml;
bool reversed_irq_handling;
};
@@ -208,6 +211,7 @@
.f_max = 208000000,
.explicit_mclk_control = true,
.qcom_fifo = true,
+ .qcom_dml = true,
};
static int mmci_card_busy(struct mmc_host *mmc)
@@ -421,6 +425,7 @@
{
const char *rxname, *txname;
dma_cap_mask_t mask;
+ struct variant_data *variant = host->variant;
host->dma_rx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "rx");
host->dma_tx_channel = dma_request_slave_channel(mmc_dev(host->mmc), "tx");
@@ -471,6 +476,10 @@
if (max_seg_size < host->mmc->max_seg_size)
host->mmc->max_seg_size = max_seg_size;
}
+
+ if (variant->qcom_dml && host->dma_rx_channel && host->dma_tx_channel)
+ if (dml_hw_init(host, host->mmc->parent->of_node))
+ variant->qcom_dml = false;
}
/*
@@ -572,6 +581,7 @@
struct dma_async_tx_descriptor *desc;
enum dma_data_direction buffer_dirn;
int nr_sg;
+ unsigned long flags = DMA_CTRL_ACK;
if (data->flags & MMC_DATA_READ) {
conf.direction = DMA_DEV_TO_MEM;
@@ -596,9 +606,12 @@
if (nr_sg == 0)
return -EINVAL;
+ if (host->variant->qcom_dml)
+ flags |= DMA_PREP_INTERRUPT;
+
dmaengine_slave_config(chan, &conf);
desc = dmaengine_prep_slave_sg(chan, data->sg, nr_sg,
- conf.direction, DMA_CTRL_ACK);
+ conf.direction, flags);
if (!desc)
goto unmap_exit;
@@ -647,6 +660,9 @@
dmaengine_submit(host->dma_desc_current);
dma_async_issue_pending(host->dma_current);
+ if (host->variant->qcom_dml)
+ dml_start_xfer(host, data);
+
datactrl |= MCI_DPSM_DMAENABLE;
/* Trigger the DMA transfer */
