libata: kill ata_id_to_dma_mode()
ata_id_to_dma_mode() isn't quite generic. The function is basically
privately implemented ata_id_xfermask() combined with hardcoded mode
printing and configuration which are specific to ata_generic.
Kill the function and open code it in generic_set_mode() using generic
xfermode handling functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index fb5434c..d11a4f1 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -63,7 +63,22 @@
/* We do need the right mode information for DMA or PIO
and this comes from the current configuration flags */
if (dma_enabled & (1 << (5 + dev->devno))) {
- ata_id_to_dma_mode(dev, XFER_MW_DMA_0);
+ unsigned int xfer_mask = ata_id_xfermask(dev->id);
+ const char *name;
+
+ if (xfer_mask & (ATA_MASK_MWDMA | ATA_MASK_UDMA))
+ name = ata_mode_string(xfer_mask);
+ else {
+ /* SWDMA perhaps? */
+ name = "DMA";
+ xfer_mask |= ata_xfer_mode2mask(XFER_MW_DMA_0);
+ }
+
+ ata_dev_printk(dev, KERN_INFO, "configured for %s\n",
+ name);
+
+ dev->xfer_mode = ata_xfer_mask2mode(xfer_mask);
+ dev->xfer_shift = ata_xfer_mode2shift(dev->xfer_mode);
dev->flags &= ~ATA_DFLAG_PIO;
} else {
ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index a70ed7b..ab84772 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1288,48 +1288,6 @@
}
/**
- * ata_id_to_dma_mode - Identify DMA mode from id block
- * @dev: device to identify
- * @unknown: mode to assume if we cannot tell
- *
- * Set up the timing values for the device based upon the identify
- * reported values for the DMA mode. This function is used by drivers
- * which rely upon firmware configured modes, but wish to report the
- * mode correctly when possible.
- *
- * In addition we emit similarly formatted messages to the default
- * ata_dev_set_mode handler, in order to provide consistency of
- * presentation.
- */
-
-void ata_id_to_dma_mode(struct ata_device *dev, u8 unknown)
-{
- unsigned int mask;
- u8 mode;
-
- /* Pack the DMA modes */
- mask = ((dev->id[63] >> 8) << ATA_SHIFT_MWDMA) & ATA_MASK_MWDMA;
- if (dev->id[53] & 0x04)
- mask |= ((dev->id[88] >> 8) << ATA_SHIFT_UDMA) & ATA_MASK_UDMA;
-
- /* Select the mode in use */
- mode = ata_xfer_mask2mode(mask);
-
- if (mode != 0xff) {
- ata_dev_printk(dev, KERN_INFO, "configured for %s\n",
- ata_mode_string(mask));
- } else {
- /* SWDMA perhaps ? */
- mode = unknown;
- ata_dev_printk(dev, KERN_INFO, "configured for DMA\n");
- }
-
- /* Configure the device reporting */
- dev->xfer_mode = mode;
- dev->xfer_shift = ata_xfer_mode2shift(mode);
-}
-
-/**
* ata_noop_dev_select - Select device 0/1 on ATA bus
* @ap: ATA channel to manipulate
* @device: ATA device (numbered from zero) to select
@@ -7653,7 +7611,6 @@
#endif /* CONFIG_PM */
EXPORT_SYMBOL_GPL(ata_id_string);
EXPORT_SYMBOL_GPL(ata_id_c_string);
-EXPORT_SYMBOL_GPL(ata_id_to_dma_mode);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index e2ed3ba..d33702fe 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -890,7 +890,6 @@
unsigned int ofs, unsigned int len);
extern void ata_id_c_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
-extern void ata_id_to_dma_mode(struct ata_device *dev, u8 unknown);
extern void ata_bmdma_setup(struct ata_queued_cmd *qc);
extern void ata_bmdma_start(struct ata_queued_cmd *qc);
extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
