Merge branch 'nop-phy-rename' into next
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-generic.c
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
index 7a95c65..3a64e20 100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -3,7 +3,7 @@
DWC3- USB3 CONTROLLER
Required properties:
- - compatible: must be "synopsys,dwc3"
+ - compatible: must be "snps,dwc3"
- reg : Address and length of the register set for the device
- interrupts: Interrupts used by the dwc3 controller.
- usb-phy : array of phandle for the PHY device
@@ -14,7 +14,7 @@
This is usually a subnode to DWC3 glue to which it is connected.
dwc3@4a030000 {
- compatible = "synopsys,dwc3";
+ compatible = "snps,dwc3";
reg = <0x4a030000 0xcfff>;
interrupts = <0 92 4>
usb-phy = <&usb2_phy>, <&usb3,phy>;
diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt
new file mode 100644
index 0000000..477d5bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/generic.txt
@@ -0,0 +1,24 @@
+Generic USB Properties
+
+Optional properties:
+ - maximum-speed: tells USB controllers we want to work up to a certain
+ speed. Valid arguments are "super-speed", "high-speed",
+ "full-speed" and "low-speed". In case this isn't passed
+ via DT, USB controllers should default to their maximum
+ HW capability.
+ - dr_mode: tells Dual-Role USB controllers that we want to work on a
+ particular mode. Valid arguments are "host",
+ "peripheral" and "otg". In case this attribute isn't
+ passed via DT, USB DRD controllers should default to
+ OTG.
+
+This is an attribute to a USB controller such as:
+
+dwc3@4a030000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x4a030000 0xcfff>;
+ interrupts = <0 92 4>
+ usb-phy = <&usb2_phy>, <&usb3,phy>;
+ maximum-speed = "super-speed";
+ dr_mode = "otg";
+};
diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
index c4c9e9e..4c8ade8 100644
--- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
@@ -48,5 +48,5 @@
peripheral means it is device controller
otg means it can operate as either ("on the go")
-Required properties for dr_mode == otg:
+VBUS control (required for dr_mode == otg, optional for dr_mode == host):
- vbus-supply: regulator for VBUS
diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt
new file mode 100644
index 0000000..b83d428
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt
@@ -0,0 +1,40 @@
+Samsung High Speed USB OTG controller
+-----------------------------
+
+The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards.
+It gives functionality of OTG-compliant USB 2.0 host and device with
+support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps)
+operation.
+
+Currently only device mode is supported.
+
+Binding details
+-----
+
+Required properties:
+- compatible: "samsung,s3c6400-hsotg" should be used for all currently
+ supported SoC,
+- interrupt-parent: phandle for the interrupt controller to which the
+ interrupt signal of the HSOTG block is routed,
+- interrupts: specifier of interrupt signal of interrupt controller,
+ according to bindings of interrupt controller,
+- clocks: contains an array of clock specifiers:
+ - first entry: OTG clock
+- clock-names: contains array of clock names:
+ - first entry: must be "otg"
+- vusb_d-supply: phandle to voltage regulator of digital section,
+- vusb_a-supply: phandle to voltage regulator of analog section.
+
+Example
+-----
+
+ hsotg@12480000 {
+ compatible = "samsung,s3c6400-hsotg";
+ reg = <0x12480000 0x20000>;
+ interrupts = <0 71 0>;
+ clocks = <&clock 305>;
+ clock-names = "otg";
+ vusb_d-supply = <&vusb_reg>;
+ vusb_a-supply = <&vusbdac_reg>;
+ };
+
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index e643620..07be2cd 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -644,7 +644,7 @@
utmi-mode = <2>;
ranges;
dwc3@4a030000 {
- compatible = "synopsys,dwc3";
+ compatible = "snps,dwc3";
reg = <0x4a030000 0x1000>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
usb-phy = <&usb2_phy>, <&usb3_phy>;
diff --git a/arch/arm/boot/dts/tegra20-seaboard.dts b/arch/arm/boot/dts/tegra20-seaboard.dts
index 365760b..52526c9 100644
--- a/arch/arm/boot/dts/tegra20-seaboard.dts
+++ b/arch/arm/boot/dts/tegra20-seaboard.dts
@@ -566,7 +566,6 @@
usb@c5000000 {
status = "okay";
- nvidia,vbus-gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
dr_mode = "otg";
};
diff --git a/arch/arm/boot/dts/tegra20-trimslice.dts b/arch/arm/boot/dts/tegra20-trimslice.dts
index ed4b901..3e57b87 100644
--- a/arch/arm/boot/dts/tegra20-trimslice.dts
+++ b/arch/arm/boot/dts/tegra20-trimslice.dts
@@ -312,7 +312,6 @@
usb@c5000000 {
status = "okay";
- nvidia,vbus-gpio = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
};
usb-phy@c5000000 {
diff --git a/arch/arm/boot/dts/tegra20-whistler.dts b/arch/arm/boot/dts/tegra20-whistler.dts
index ab67c94..a6b1b5b 100644
--- a/arch/arm/boot/dts/tegra20-whistler.dts
+++ b/arch/arm/boot/dts/tegra20-whistler.dts
@@ -509,7 +509,6 @@
usb@c5000000 {
status = "okay";
- nvidia,vbus-gpio = <&tca6416 0 GPIO_ACTIVE_HIGH>;
};
usb-phy@c5000000 {
@@ -519,7 +518,6 @@
usb@c5008000 {
status = "okay";
- nvidia,vbus-gpio = <&tca6416 1 GPIO_ACTIVE_HIGH>;
};
usb-phy@c5008000 {
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index 9653fd8..e457083 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -477,13 +477,13 @@
<&tegra_car TEGRA20_CLK_USBD>;
clock-names = "reg", "pll_u", "timer", "utmi-pads";
nvidia,has-legacy-mode;
- hssync_start_delay = <9>;
- idle_wait_delay = <17>;
- elastic_limit = <16>;
- term_range_adj = <6>;
- xcvr_setup = <9>;
- xcvr_lsfslew = <1>;
- xcvr_lsrslew = <1>;
+ nvidia,hssync-start-delay = <9>;
+ nvidia,idle-wait-delay = <17>;
+ nvidia,elastic-limit = <16>;
+ nvidia,term-range-adj = <6>;
+ nvidia,xcvr-setup = <9>;
+ nvidia,xcvr-lsfslew = <1>;
+ nvidia,xcvr-lsrslew = <1>;
status = "disabled";
};
@@ -527,13 +527,13 @@
<&tegra_car TEGRA20_CLK_CLK_M>,
<&tegra_car TEGRA20_CLK_USBD>;
clock-names = "reg", "pll_u", "timer", "utmi-pads";
- hssync_start_delay = <9>;
- idle_wait_delay = <17>;
- elastic_limit = <16>;
- term_range_adj = <6>;
- xcvr_setup = <9>;
- xcvr_lsfslew = <2>;
- xcvr_lsrslew = <2>;
+ nvidia,hssync-start-delay = <9>;
+ nvidia,idle-wait-delay = <17>;
+ nvidia,elastic-limit = <16>;
+ nvidia,term-range-adj = <6>;
+ nvidia,xcvr-setup = <9>;
+ nvidia,xcvr-lsfslew = <2>;
+ nvidia,xcvr-lsrslew = <2>;
status = "disabled";
};
diff --git a/arch/arm/mach-tegra/tegra.c b/arch/arm/mach-tegra/tegra.c
index 0d1e412..fc97cfd 100644
--- a/arch/arm/mach-tegra/tegra.c
+++ b/arch/arm/mach-tegra/tegra.c
@@ -29,7 +29,6 @@
#include <linux/of_fdt.h>
#include <linux/of_platform.h>
#include <linux/pda_power.h>
-#include <linux/platform_data/tegra_usb.h>
#include <linux/io.h>
#include <linux/slab.h>
#include <linux/sys_soc.h>
@@ -46,40 +45,6 @@
#include "fuse.h"
#include "iomap.h"
-static struct tegra_ehci_platform_data tegra_ehci1_pdata = {
- .operating_mode = TEGRA_USB_OTG,
- .power_down_on_bus_suspend = 1,
- .vbus_gpio = -1,
-};
-
-static struct tegra_ulpi_config tegra_ehci2_ulpi_phy_config = {
- .reset_gpio = -1,
- .clk = "cdev2",
-};
-
-static struct tegra_ehci_platform_data tegra_ehci2_pdata = {
- .phy_config = &tegra_ehci2_ulpi_phy_config,
- .operating_mode = TEGRA_USB_HOST,
- .power_down_on_bus_suspend = 1,
- .vbus_gpio = -1,
-};
-
-static struct tegra_ehci_platform_data tegra_ehci3_pdata = {
- .operating_mode = TEGRA_USB_HOST,
- .power_down_on_bus_suspend = 1,
- .vbus_gpio = -1,
-};
-
-static struct of_dev_auxdata tegra20_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("nvidia,tegra20-ehci", 0xC5000000, "tegra-ehci.0",
- &tegra_ehci1_pdata),
- OF_DEV_AUXDATA("nvidia,tegra20-ehci", 0xC5004000, "tegra-ehci.1",
- &tegra_ehci2_pdata),
- OF_DEV_AUXDATA("nvidia,tegra20-ehci", 0xC5008000, "tegra-ehci.2",
- &tegra_ehci3_pdata),
- {}
-};
-
static void __init tegra_dt_init(void)
{
struct soc_device_attribute *soc_dev_attr;
@@ -112,8 +77,7 @@
* devices
*/
out:
- of_platform_populate(NULL, of_default_bus_match_table,
- tegra20_auxdata_lookup, parent);
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, parent);
}
static void __init trimslice_init(void)
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index 238c5d4..2b3132e 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -45,7 +45,7 @@
obj-$(CONFIG_USB_SERIAL) += serial/
obj-$(CONFIG_USB) += misc/
-obj-$(CONFIG_USB_PHY) += phy/
+obj-$(CONFIG_USB_SUPPORT) += phy/
obj-$(CONFIG_EARLY_PRINTK_DBGP) += early/
obj-$(CONFIG_USB_ATM) += atm/
diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
index 2378958..3e225d5 100644
--- a/drivers/usb/dwc3/Kconfig
+++ b/drivers/usb/dwc3/Kconfig
@@ -40,6 +40,38 @@
endchoice
+comment "Platform Glue Driver Support"
+
+config USB_DWC3_OMAP
+ tristate "Texas Instruments OMAP5 and similar Platforms"
+ depends on EXTCON
+ default USB_DWC3
+ help
+ Some platforms from Texas Instruments like OMAP5, DRA7xxx and
+ AM437x use this IP for USB2/3 functionality.
+
+ Say 'Y' or 'M' here if you have one such device
+
+config USB_DWC3_EXYNOS
+ tristate "Samsung Exynos Platform"
+ default USB_DWC3
+ help
+ Recent Exynos5 SoCs ship with one DesignWare Core USB3 IP inside,
+ say 'Y' or 'M' if you have one such device.
+
+config USB_DWC3_PCI
+ tristate "PCIe-based Platforms"
+ depends on PCI
+ default USB_DWC3
+ help
+ If you're using the DesignWare Core IP with a PCIe, please say
+ 'Y' or 'M' here.
+
+ One such PCIe-based platform is Synopsys' PCIe HAPS model of
+ this IP.
+
+comment "Debugging features"
+
config USB_DWC3_DEBUG
bool "Enable Debugging Messages"
help
diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
index 0c7ac92..dd17601 100644
--- a/drivers/usb/dwc3/Makefile
+++ b/drivers/usb/dwc3/Makefile
@@ -27,15 +27,8 @@
# the entire driver (with all its glue layers) on several architectures
# and make sure it compiles fine. This will also help with allmodconfig
# and allyesconfig builds.
-#
-# The only exception is the PCI glue layer, but that's only because
-# PCI doesn't provide nops if CONFIG_PCI isn't enabled.
##
-obj-$(CONFIG_USB_DWC3) += dwc3-omap.o
-obj-$(CONFIG_USB_DWC3) += dwc3-exynos.o
-
-ifneq ($(CONFIG_PCI),)
- obj-$(CONFIG_USB_DWC3) += dwc3-pci.o
-endif
-
+obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
+obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
+obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 358375e..3ff6f0a 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -6,34 +6,17 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/module.h>
@@ -53,17 +36,16 @@
#include <linux/usb/otg.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
+#include <linux/usb/of.h>
+#include <linux/usb/otg.h>
+#include "platform_data.h"
#include "core.h"
#include "gadget.h"
#include "io.h"
#include "debug.h"
-static char *maximum_speed = "super";
-module_param(maximum_speed, charp, 0);
-MODULE_PARM_DESC(maximum_speed, "Maximum supported speed.");
-
/* -------------------------------------------------------------------------- */
void dwc3_set_mode(struct dwc3 *dwc, u32 mode)
@@ -236,7 +218,7 @@
dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(n),
upper_32_bits(evt->dma));
dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(n),
- evt->length & 0xffff);
+ DWC3_GEVNTSIZ_SIZE(evt->length));
dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(n), 0);
}
@@ -255,7 +237,8 @@
dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(n), 0);
dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(n), 0);
- dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(n), 0);
+ dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(n), DWC3_GEVNTSIZ_INTMASK
+ | DWC3_GEVNTSIZ_SIZE(0));
dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(n), 0);
}
}
@@ -367,18 +350,17 @@
static int dwc3_probe(struct platform_device *pdev)
{
- struct device_node *node = pdev->dev.of_node;
+ struct device *dev = &pdev->dev;
+ struct dwc3_platform_data *pdata = dev_get_platdata(dev);
+ struct device_node *node = dev->of_node;
struct resource *res;
struct dwc3 *dwc;
- struct device *dev = &pdev->dev;
int ret = -ENOMEM;
void __iomem *regs;
void *mem;
- u8 mode;
-
mem = devm_kzalloc(dev, sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
if (!mem) {
dev_err(dev, "not enough memory\n");
@@ -402,38 +384,29 @@
dev_err(dev, "missing memory resource\n");
return -ENODEV;
}
- dwc->xhci_resources[0].start = res->start;
- dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
- DWC3_XHCI_REGS_END;
- dwc->xhci_resources[0].flags = res->flags;
- dwc->xhci_resources[0].name = res->name;
-
- /*
- * Request memory region but exclude xHCI regs,
- * since it will be requested by the xhci-plat driver.
- */
- res = devm_request_mem_region(dev, res->start + DWC3_GLOBALS_REGS_START,
- resource_size(res) - DWC3_GLOBALS_REGS_START,
- dev_name(dev));
- if (!res) {
- dev_err(dev, "can't request mem region\n");
- return -ENOMEM;
- }
-
- regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (!regs) {
- dev_err(dev, "ioremap failed\n");
- return -ENOMEM;
- }
if (node) {
+ dwc->maximum_speed = of_usb_get_maximum_speed(node);
+
dwc->usb2_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 0);
dwc->usb3_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 1);
+
+ dwc->needs_fifo_resize = of_property_read_bool(node, "tx-fifo-resize");
+ dwc->dr_mode = of_usb_get_dr_mode(node);
} else {
+ dwc->maximum_speed = pdata->maximum_speed;
+
dwc->usb2_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3);
+
+ dwc->needs_fifo_resize = pdata->tx_fifo_resize;
+ dwc->dr_mode = pdata->dr_mode;
}
+ /* default to superspeed if no maximum_speed passed */
+ if (dwc->maximum_speed == USB_SPEED_UNKNOWN)
+ dwc->maximum_speed = USB_SPEED_SUPER;
+
if (IS_ERR(dwc->usb2_phy)) {
ret = PTR_ERR(dwc->usb2_phy);
@@ -464,6 +437,22 @@
return -EPROBE_DEFER;
}
+ dwc->xhci_resources[0].start = res->start;
+ dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
+ DWC3_XHCI_REGS_END;
+ dwc->xhci_resources[0].flags = res->flags;
+ dwc->xhci_resources[0].name = res->name;
+
+ res->start += DWC3_GLOBALS_REGS_START;
+
+ /*
+ * Request memory region but exclude xHCI regs,
+ * since it will be requested by the xhci-plat driver.
+ */
+ regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(regs))
+ return PTR_ERR(regs);
+
usb_phy_set_suspend(dwc->usb2_phy, 0);
usb_phy_set_suspend(dwc->usb3_phy, 0);
@@ -478,19 +467,6 @@
dev->dma_parms = dev->parent->dma_parms;
dma_set_coherent_mask(dev, dev->parent->coherent_dma_mask);
- if (!strncmp("super", maximum_speed, 5))
- dwc->maximum_speed = DWC3_DCFG_SUPERSPEED;
- else if (!strncmp("high", maximum_speed, 4))
- dwc->maximum_speed = DWC3_DCFG_HIGHSPEED;
- else if (!strncmp("full", maximum_speed, 4))
- dwc->maximum_speed = DWC3_DCFG_FULLSPEED1;
- else if (!strncmp("low", maximum_speed, 3))
- dwc->maximum_speed = DWC3_DCFG_LOWSPEED;
- else
- dwc->maximum_speed = DWC3_DCFG_SUPERSPEED;
-
- dwc->needs_fifo_resize = of_property_read_bool(node, "tx-fifo-resize");
-
pm_runtime_enable(dev);
pm_runtime_get_sync(dev);
pm_runtime_forbid(dev);
@@ -517,14 +493,15 @@
}
if (IS_ENABLED(CONFIG_USB_DWC3_HOST))
- mode = DWC3_MODE_HOST;
+ dwc->dr_mode = USB_DR_MODE_HOST;
else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET))
- mode = DWC3_MODE_DEVICE;
- else
- mode = DWC3_MODE_DRD;
+ dwc->dr_mode = USB_DR_MODE_PERIPHERAL;
- switch (mode) {
- case DWC3_MODE_DEVICE:
+ if (dwc->dr_mode == USB_DR_MODE_UNKNOWN)
+ dwc->dr_mode = USB_DR_MODE_OTG;
+
+ switch (dwc->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_DEVICE);
ret = dwc3_gadget_init(dwc);
if (ret) {
@@ -532,7 +509,7 @@
goto err2;
}
break;
- case DWC3_MODE_HOST:
+ case USB_DR_MODE_HOST:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_HOST);
ret = dwc3_host_init(dwc);
if (ret) {
@@ -540,7 +517,7 @@
goto err2;
}
break;
- case DWC3_MODE_DRD:
+ case USB_DR_MODE_OTG:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_OTG);
ret = dwc3_host_init(dwc);
if (ret) {
@@ -555,10 +532,9 @@
}
break;
default:
- dev_err(dev, "Unsupported mode of operation %d\n", mode);
+ dev_err(dev, "Unsupported mode of operation %d\n", dwc->dr_mode);
goto err2;
}
- dwc->mode = mode;
ret = dwc3_debugfs_init(dwc);
if (ret) {
@@ -571,14 +547,14 @@
return 0;
err3:
- switch (mode) {
- case DWC3_MODE_DEVICE:
+ switch (dwc->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
dwc3_gadget_exit(dwc);
break;
- case DWC3_MODE_HOST:
+ case USB_DR_MODE_HOST:
dwc3_host_exit(dwc);
break;
- case DWC3_MODE_DRD:
+ case USB_DR_MODE_OTG:
dwc3_host_exit(dwc);
dwc3_gadget_exit(dwc);
break;
@@ -611,14 +587,14 @@
dwc3_debugfs_exit(dwc);
- switch (dwc->mode) {
- case DWC3_MODE_DEVICE:
+ switch (dwc->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
dwc3_gadget_exit(dwc);
break;
- case DWC3_MODE_HOST:
+ case USB_DR_MODE_HOST:
dwc3_host_exit(dwc);
break;
- case DWC3_MODE_DRD:
+ case USB_DR_MODE_OTG:
dwc3_host_exit(dwc);
dwc3_gadget_exit(dwc);
break;
@@ -642,12 +618,12 @@
spin_lock_irqsave(&dwc->lock, flags);
- switch (dwc->mode) {
- case DWC3_MODE_DEVICE:
- case DWC3_MODE_DRD:
+ switch (dwc->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
+ case USB_DR_MODE_OTG:
dwc3_gadget_prepare(dwc);
/* FALLTHROUGH */
- case DWC3_MODE_HOST:
+ case USB_DR_MODE_HOST:
default:
dwc3_event_buffers_cleanup(dwc);
break;
@@ -665,12 +641,12 @@
spin_lock_irqsave(&dwc->lock, flags);
- switch (dwc->mode) {
- case DWC3_MODE_DEVICE:
- case DWC3_MODE_DRD:
+ switch (dwc->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
+ case USB_DR_MODE_OTG:
dwc3_gadget_complete(dwc);
/* FALLTHROUGH */
- case DWC3_MODE_HOST:
+ case USB_DR_MODE_HOST:
default:
dwc3_event_buffers_setup(dwc);
break;
@@ -686,12 +662,12 @@
spin_lock_irqsave(&dwc->lock, flags);
- switch (dwc->mode) {
- case DWC3_MODE_DEVICE:
- case DWC3_MODE_DRD:
+ switch (dwc->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
+ case USB_DR_MODE_OTG:
dwc3_gadget_suspend(dwc);
/* FALLTHROUGH */
- case DWC3_MODE_HOST:
+ case USB_DR_MODE_HOST:
default:
/* do nothing */
break;
@@ -719,12 +695,12 @@
dwc3_writel(dwc->regs, DWC3_GCTL, dwc->gctl);
- switch (dwc->mode) {
- case DWC3_MODE_DEVICE:
- case DWC3_MODE_DRD:
+ switch (dwc->dr_mode) {
+ case USB_DR_MODE_PERIPHERAL:
+ case USB_DR_MODE_OTG:
dwc3_gadget_resume(dwc);
/* FALLTHROUGH */
- case DWC3_MODE_HOST:
+ case USB_DR_MODE_HOST:
default:
/* do nothing */
break;
@@ -754,6 +730,9 @@
#ifdef CONFIG_OF
static const struct of_device_id of_dwc3_match[] = {
{
+ .compatible = "snps,dwc3"
+ },
+ {
.compatible = "synopsys,dwc3"
},
{ },
@@ -775,5 +754,5 @@
MODULE_ALIAS("platform:dwc3");
MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
-MODULE_LICENSE("Dual BSD/GPL");
+MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("DesignWare USB3 DRD Controller Driver");
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 27dad99..f8af8d4 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#ifndef __DRIVERS_USB_DWC3_CORE_H
@@ -49,6 +29,7 @@
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
+#include <linux/usb/otg.h>
/* Global constants */
#define DWC3_EP0_BOUNCE_SIZE 512
@@ -194,6 +175,10 @@
#define DWC3_GTXFIFOSIZ_TXFDEF(n) ((n) & 0xffff)
#define DWC3_GTXFIFOSIZ_TXFSTADDR(n) ((n) & 0xffff0000)
+/* Global Event Size Registers */
+#define DWC3_GEVNTSIZ_INTMASK (1 << 31)
+#define DWC3_GEVNTSIZ_SIZE(n) ((n) & 0xffff)
+
/* Global HWPARAMS1 Register */
#define DWC3_GHWPARAMS1_EN_PWROPT(n) (((n) & (3 << 24)) >> 24)
#define DWC3_GHWPARAMS1_EN_PWROPT_NO 0
@@ -207,7 +192,6 @@
#define DWC3_MAX_HIBER_SCRATCHBUFS 15
/* Device Configuration Register */
-#define DWC3_DCFG_LPM_CAP (1 << 22)
#define DWC3_DCFG_DEVADDR(addr) ((addr) << 3)
#define DWC3_DCFG_DEVADDR_MASK DWC3_DCFG_DEVADDR(0x7f)
@@ -367,7 +351,6 @@
/**
* struct dwc3_event_buffer - Software event buffer representation
- * @list: a list of event buffers
* @buf: _THE_ buffer
* @length: size of this buffer
* @lpos: event offset
@@ -415,7 +398,7 @@
* @number: endpoint number (1 - 15)
* @type: set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK
* @resource_index: Resource transfer index
- * @interval: the intervall on which the ISOC transfer is started
+ * @interval: the interval on which the ISOC transfer is started
* @name: a human readable name e.g. ep1out-bulk
* @direction: true for TX, false for RX
* @stream_capable: true when streams are enabled
@@ -566,11 +549,6 @@
/* HWPARAMS0 */
#define DWC3_MODE(n) ((n) & 0x7)
-#define DWC3_MODE_DEVICE 0
-#define DWC3_MODE_HOST 1
-#define DWC3_MODE_DRD 2
-#define DWC3_MODE_HUB 3
-
#define DWC3_MDWIDTH(n) (((n) & 0xff00) >> 8)
/* HWPARAMS1 */
@@ -632,7 +610,7 @@
* @u1u2: only used on revisions <1.83a for workaround
* @maximum_speed: maximum speed requested (mainly for testing purposes)
* @revision: revision register contents
- * @mode: mode of operation
+ * @dr_mode: requested mode of operation
* @usb2_phy: pointer to USB2 PHY
* @usb3_phy: pointer to USB3 PHY
* @dcfg: saved contents of DCFG register
@@ -690,6 +668,8 @@
void __iomem *regs;
size_t regs_size;
+ enum usb_dr_mode dr_mode;
+
/* used for suspend/resume */
u32 dcfg;
u32 gctl;
@@ -698,7 +678,6 @@
u32 u1u2;
u32 maximum_speed;
u32 revision;
- u32 mode;
#define DWC3_REVISION_173A 0x5533173a
#define DWC3_REVISION_175A 0x5533175a
diff --git a/drivers/usb/dwc3/debug.h b/drivers/usb/dwc3/debug.h
index 5894ee8..fceb39d 100644
--- a/drivers/usb/dwc3/debug.h
+++ b/drivers/usb/dwc3/debug.h
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include "core.h"
diff --git a/drivers/usb/dwc3/debugfs.c b/drivers/usb/dwc3/debugfs.c
index 9e9f122..9ac37fe 100644
--- a/drivers/usb/dwc3/debugfs.c
+++ b/drivers/usb/dwc3/debugfs.c
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include <linux/kernel.h>
diff --git a/drivers/usb/dwc3/dwc3-exynos.c b/drivers/usb/dwc3/dwc3-exynos.c
index a179c5a..2f2e88a 100644
--- a/drivers/usb/dwc3/dwc3-exynos.c
+++ b/drivers/usb/dwc3/dwc3-exynos.c
@@ -6,10 +6,14 @@
*
* Author: Anton Tikhomirov <av.tikhomirov@samsung.com>
*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include <linux/module.h>
@@ -228,5 +232,5 @@
MODULE_ALIAS("platform:exynos-dwc3");
MODULE_AUTHOR("Anton Tikhomirov <av.tikhomirov@samsung.com>");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("DesignWare USB3 EXYNOS Glue Layer");
diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c
index 077f110b..ecd9945 100644
--- a/drivers/usb/dwc3/dwc3-omap.c
+++ b/drivers/usb/dwc3/dwc3-omap.c
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include <linux/module.h>
@@ -409,11 +389,9 @@
return -EINVAL;
}
- base = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (!base) {
- dev_err(dev, "ioremap failed\n");
- return -ENOMEM;
- }
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
spin_lock_init(&omap->lock);
@@ -610,5 +588,5 @@
MODULE_ALIAS("platform:omap-dwc3");
MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
-MODULE_LICENSE("Dual BSD/GPL");
+MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("DesignWare USB3 OMAP Glue Layer");
diff --git a/drivers/usb/dwc3/dwc3-pci.c b/drivers/usb/dwc3/dwc3-pci.c
index 87ea3d5..9b13812 100644
--- a/drivers/usb/dwc3/dwc3-pci.c
+++ b/drivers/usb/dwc3/dwc3-pci.c
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include <linux/kernel.h>
@@ -211,7 +191,7 @@
};
MODULE_DEVICE_TABLE(pci, dwc3_pci_id_table);
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
static int dwc3_pci_suspend(struct device *dev)
{
struct pci_dev *pci = to_pci_dev(dev);
@@ -236,28 +216,24 @@
return 0;
}
+#endif /* CONFIG_PM_SLEEP */
static const struct dev_pm_ops dwc3_pci_dev_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(dwc3_pci_suspend, dwc3_pci_resume)
};
-#define DEV_PM_OPS (&dwc3_pci_dev_pm_ops)
-#else
-#define DEV_PM_OPS NULL
-#endif /* CONFIG_PM */
-
static struct pci_driver dwc3_pci_driver = {
.name = "dwc3-pci",
.id_table = dwc3_pci_id_table,
.probe = dwc3_pci_probe,
.remove = dwc3_pci_remove,
.driver = {
- .pm = DEV_PM_OPS,
+ .pm = &dwc3_pci_dev_pm_ops,
},
};
MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
-MODULE_LICENSE("Dual BSD/GPL");
+MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("DesignWare USB3 PCI Glue Layer");
module_pci_driver(dwc3_pci_driver);
diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
index 5acbb94..7fa93f4 100644
--- a/drivers/usb/dwc3/ep0.c
+++ b/drivers/usb/dwc3/ep0.c
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include <linux/kernel.h>
@@ -168,6 +148,7 @@
direction = !dwc->ep0_expect_in;
dwc->delayed_status = false;
+ usb_gadget_set_state(&dwc->gadget, USB_STATE_CONFIGURED);
if (dwc->ep0state == EP0_STATUS_PHASE)
__dwc3_ep0_do_control_status(dwc, dwc->eps[direction]);
@@ -553,8 +534,16 @@
ret = dwc3_ep0_delegate_req(dwc, ctrl);
/* if the cfg matches and the cfg is non zero */
if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {
- usb_gadget_set_state(&dwc->gadget,
- USB_STATE_CONFIGURED);
+
+ /*
+ * only change state if set_config has already
+ * been processed. If gadget driver returns
+ * USB_GADGET_DELAYED_STATUS, we will wait
+ * to change the state on the next usb_ep_queue()
+ */
+ if (ret == 0)
+ usb_gadget_set_state(&dwc->gadget,
+ USB_STATE_CONFIGURED);
/*
* Enable transition to U1/U2 state when
@@ -571,7 +560,7 @@
case USB_STATE_CONFIGURED:
ret = dwc3_ep0_delegate_req(dwc, ctrl);
- if (!cfg)
+ if (!cfg && !ret)
usb_gadget_set_state(&dwc->gadget,
USB_STATE_ADDRESS);
break;
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index f77083f..f168eae 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include <linux/kernel.h>
@@ -520,6 +500,8 @@
u32 reg;
int ret = -ENOMEM;
+ dev_vdbg(dwc->dev, "Enabling %s\n", dep->name);
+
if (!(dep->flags & DWC3_EP_ENABLED)) {
ret = dwc3_gadget_start_config(dwc, dep);
if (ret)
@@ -676,8 +658,6 @@
dev_err(dwc->dev, "invalid endpoint transfer type\n");
}
- dev_vdbg(dwc->dev, "Enabling %s\n", dep->name);
-
spin_lock_irqsave(&dwc->lock, flags);
ret = __dwc3_gadget_ep_enable(dep, desc, ep->comp_desc, false);
spin_unlock_irqrestore(&dwc->lock, flags);
@@ -1508,6 +1488,15 @@
int irq;
u32 reg;
+ irq = platform_get_irq(to_platform_device(dwc->dev), 0);
+ ret = request_threaded_irq(irq, dwc3_interrupt, dwc3_thread_interrupt,
+ IRQF_SHARED, "dwc3", dwc);
+ if (ret) {
+ dev_err(dwc->dev, "failed to request irq #%d --> %d\n",
+ irq, ret);
+ goto err0;
+ }
+
spin_lock_irqsave(&dwc->lock, flags);
if (dwc->gadget_driver) {
@@ -1515,7 +1504,7 @@
dwc->gadget.name,
dwc->gadget_driver->driver.name);
ret = -EBUSY;
- goto err0;
+ goto err1;
}
dwc->gadget_driver = driver;
@@ -1536,10 +1525,25 @@
* STAR#9000525659: Clock Domain Crossing on DCTL in
* USB 2.0 Mode
*/
- if (dwc->revision < DWC3_REVISION_220A)
+ if (dwc->revision < DWC3_REVISION_220A) {
reg |= DWC3_DCFG_SUPERSPEED;
- else
- reg |= dwc->maximum_speed;
+ } else {
+ switch (dwc->maximum_speed) {
+ case USB_SPEED_LOW:
+ reg |= DWC3_DSTS_LOWSPEED;
+ break;
+ case USB_SPEED_FULL:
+ reg |= DWC3_DSTS_FULLSPEED1;
+ break;
+ case USB_SPEED_HIGH:
+ reg |= DWC3_DSTS_HIGHSPEED;
+ break;
+ case USB_SPEED_SUPER: /* FALLTHROUGH */
+ case USB_SPEED_UNKNOWN: /* FALTHROUGH */
+ default:
+ reg |= DWC3_DSTS_SUPERSPEED;
+ }
+ }
dwc3_writel(dwc->regs, DWC3_DCFG, reg);
dwc->start_config_issued = false;
@@ -1551,42 +1555,38 @@
ret = __dwc3_gadget_ep_enable(dep, &dwc3_gadget_ep0_desc, NULL, false);
if (ret) {
dev_err(dwc->dev, "failed to enable %s\n", dep->name);
- goto err0;
+ goto err2;
}
dep = dwc->eps[1];
ret = __dwc3_gadget_ep_enable(dep, &dwc3_gadget_ep0_desc, NULL, false);
if (ret) {
dev_err(dwc->dev, "failed to enable %s\n", dep->name);
- goto err1;
+ goto err3;
}
/* begin to receive SETUP packets */
dwc->ep0state = EP0_SETUP_PHASE;
dwc3_ep0_out_start(dwc);
- irq = platform_get_irq(to_platform_device(dwc->dev), 0);
- ret = request_threaded_irq(irq, dwc3_interrupt, dwc3_thread_interrupt,
- IRQF_SHARED | IRQF_ONESHOT, "dwc3", dwc);
- if (ret) {
- dev_err(dwc->dev, "failed to request irq #%d --> %d\n",
- irq, ret);
- goto err1;
- }
-
dwc3_gadget_enable_irq(dwc);
spin_unlock_irqrestore(&dwc->lock, flags);
return 0;
-err1:
+err3:
__dwc3_gadget_ep_disable(dwc->eps[0]);
-err0:
+err2:
dwc->gadget_driver = NULL;
+
+err1:
spin_unlock_irqrestore(&dwc->lock, flags);
+ free_irq(irq, dwc);
+
+err0:
return ret;
}
@@ -1600,9 +1600,6 @@
spin_lock_irqsave(&dwc->lock, flags);
dwc3_gadget_disable_irq(dwc);
- irq = platform_get_irq(to_platform_device(dwc->dev), 0);
- free_irq(irq, dwc);
-
__dwc3_gadget_ep_disable(dwc->eps[0]);
__dwc3_gadget_ep_disable(dwc->eps[1]);
@@ -1610,6 +1607,9 @@
spin_unlock_irqrestore(&dwc->lock, flags);
+ irq = platform_get_irq(to_platform_device(dwc->dev), 0);
+ free_irq(irq, dwc);
+
return 0;
}
@@ -1642,13 +1642,15 @@
dep->dwc = dwc;
dep->number = epnum;
+ dep->direction = !!direction;
dwc->eps[epnum] = dep;
snprintf(dep->name, sizeof(dep->name), "ep%d%s", epnum >> 1,
(epnum & 1) ? "in" : "out");
dep->endpoint.name = dep->name;
- dep->direction = (epnum & 1);
+
+ dev_vdbg(dwc->dev, "initializing %s\n", dep->name);
if (epnum == 0 || epnum == 1) {
dep->endpoint.maxpacket = 512;
@@ -2105,34 +2107,6 @@
dwc->setup_packet_pending = false;
}
-static void dwc3_gadget_usb3_phy_suspend(struct dwc3 *dwc, int suspend)
-{
- u32 reg;
-
- reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
-
- if (suspend)
- reg |= DWC3_GUSB3PIPECTL_SUSPHY;
- else
- reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
-
- dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
-}
-
-static void dwc3_gadget_usb2_phy_suspend(struct dwc3 *dwc, int suspend)
-{
- u32 reg;
-
- reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
-
- if (suspend)
- reg |= DWC3_GUSB2PHYCFG_SUSPHY;
- else
- reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
-
- dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
-}
-
static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
{
u32 reg;
@@ -2173,13 +2147,6 @@
/* after reset -> Default State */
usb_gadget_set_state(&dwc->gadget, USB_STATE_DEFAULT);
- /* Recent versions support automatic phy suspend and don't need this */
- if (dwc->revision < DWC3_REVISION_194A) {
- /* Resume PHYs */
- dwc3_gadget_usb2_phy_suspend(dwc, false);
- dwc3_gadget_usb3_phy_suspend(dwc, false);
- }
-
if (dwc->gadget.speed != USB_SPEED_UNKNOWN)
dwc3_disconnect_gadget(dwc);
@@ -2223,20 +2190,6 @@
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
}
-static void dwc3_gadget_phy_suspend(struct dwc3 *dwc, u8 speed)
-{
- switch (speed) {
- case USB_SPEED_SUPER:
- dwc3_gadget_usb2_phy_suspend(dwc, true);
- break;
- case USB_SPEED_HIGH:
- case USB_SPEED_FULL:
- case USB_SPEED_LOW:
- dwc3_gadget_usb3_phy_suspend(dwc, true);
- break;
- }
-}
-
static void dwc3_gadget_conndone_interrupt(struct dwc3 *dwc)
{
struct dwc3_ep *dep;
@@ -2312,12 +2265,6 @@
dwc3_writel(dwc->regs, DWC3_DCTL, reg);
}
- /* Recent versions support automatic phy suspend and don't need this */
- if (dwc->revision < DWC3_REVISION_194A) {
- /* Suspend unneeded PHY */
- dwc3_gadget_phy_suspend(dwc, dwc->gadget.speed);
- }
-
dep = dwc->eps[0];
ret = __dwc3_gadget_ep_enable(dep, &dwc3_gadget_ep0_desc, NULL, true);
if (ret) {
@@ -2495,6 +2442,53 @@
}
}
+static irqreturn_t dwc3_process_event_buf(struct dwc3 *dwc, u32 buf)
+{
+ struct dwc3_event_buffer *evt;
+ irqreturn_t ret = IRQ_NONE;
+ int left;
+ u32 reg;
+
+ evt = dwc->ev_buffs[buf];
+ left = evt->count;
+
+ if (!(evt->flags & DWC3_EVENT_PENDING))
+ return IRQ_NONE;
+
+ while (left > 0) {
+ union dwc3_event event;
+
+ event.raw = *(u32 *) (evt->buf + evt->lpos);
+
+ dwc3_process_event_entry(dwc, &event);
+
+ /*
+ * FIXME we wrap around correctly to the next entry as
+ * almost all entries are 4 bytes in size. There is one
+ * entry which has 12 bytes which is a regular entry
+ * followed by 8 bytes data. ATM I don't know how
+ * things are organized if we get next to the a
+ * boundary so I worry about that once we try to handle
+ * that.
+ */
+ evt->lpos = (evt->lpos + 4) % DWC3_EVENT_BUFFERS_SIZE;
+ left -= 4;
+
+ dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(buf), 4);
+ }
+
+ evt->count = 0;
+ evt->flags &= ~DWC3_EVENT_PENDING;
+ ret = IRQ_HANDLED;
+
+ /* Unmask interrupt */
+ reg = dwc3_readl(dwc->regs, DWC3_GEVNTSIZ(buf));
+ reg &= ~DWC3_GEVNTSIZ_INTMASK;
+ dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(buf), reg);
+
+ return ret;
+}
+
static irqreturn_t dwc3_thread_interrupt(int irq, void *_dwc)
{
struct dwc3 *dwc = _dwc;
@@ -2504,52 +2498,19 @@
spin_lock_irqsave(&dwc->lock, flags);
- for (i = 0; i < dwc->num_event_buffers; i++) {
- struct dwc3_event_buffer *evt;
- int left;
-
- evt = dwc->ev_buffs[i];
- left = evt->count;
-
- if (!(evt->flags & DWC3_EVENT_PENDING))
- continue;
-
- while (left > 0) {
- union dwc3_event event;
-
- event.raw = *(u32 *) (evt->buf + evt->lpos);
-
- dwc3_process_event_entry(dwc, &event);
-
- /*
- * FIXME we wrap around correctly to the next entry as
- * almost all entries are 4 bytes in size. There is one
- * entry which has 12 bytes which is a regular entry
- * followed by 8 bytes data. ATM I don't know how
- * things are organized if we get next to the a
- * boundary so I worry about that once we try to handle
- * that.
- */
- evt->lpos = (evt->lpos + 4) % DWC3_EVENT_BUFFERS_SIZE;
- left -= 4;
-
- dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(i), 4);
- }
-
- evt->count = 0;
- evt->flags &= ~DWC3_EVENT_PENDING;
- ret = IRQ_HANDLED;
- }
+ for (i = 0; i < dwc->num_event_buffers; i++)
+ ret |= dwc3_process_event_buf(dwc, i);
spin_unlock_irqrestore(&dwc->lock, flags);
return ret;
}
-static irqreturn_t dwc3_process_event_buf(struct dwc3 *dwc, u32 buf)
+static irqreturn_t dwc3_check_event_buf(struct dwc3 *dwc, u32 buf)
{
struct dwc3_event_buffer *evt;
u32 count;
+ u32 reg;
evt = dwc->ev_buffs[buf];
@@ -2561,6 +2522,11 @@
evt->count = count;
evt->flags |= DWC3_EVENT_PENDING;
+ /* Mask interrupt */
+ reg = dwc3_readl(dwc->regs, DWC3_GEVNTSIZ(buf));
+ reg |= DWC3_GEVNTSIZ_INTMASK;
+ dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(buf), reg);
+
return IRQ_WAKE_THREAD;
}
@@ -2575,7 +2541,7 @@
for (i = 0; i < dwc->num_event_buffers; i++) {
irqreturn_t status;
- status = dwc3_process_event_buf(dwc, i);
+ status = dwc3_check_event_buf(dwc, i);
if (status == IRQ_WAKE_THREAD)
ret = status;
}
@@ -2593,7 +2559,6 @@
*/
int dwc3_gadget_init(struct dwc3 *dwc)
{
- u32 reg;
int ret;
dwc->ctrl_req = dma_alloc_coherent(dwc->dev, sizeof(*dwc->ctrl_req),
@@ -2643,16 +2608,6 @@
if (ret)
goto err4;
- reg = dwc3_readl(dwc->regs, DWC3_DCFG);
- reg |= DWC3_DCFG_LPM_CAP;
- dwc3_writel(dwc->regs, DWC3_DCFG, reg);
-
- /* Enable USB2 LPM and automatic phy suspend only on recent versions */
- if (dwc->revision >= DWC3_REVISION_194A) {
- dwc3_gadget_usb2_phy_suspend(dwc, false);
- dwc3_gadget_usb3_phy_suspend(dwc, false);
- }
-
ret = usb_add_gadget_udc(dwc->dev, &dwc->gadget);
if (ret) {
dev_err(dwc->dev, "failed to register udc\n");
diff --git a/drivers/usb/dwc3/gadget.h b/drivers/usb/dwc3/gadget.h
index 99e6d72..febe1aa 100644
--- a/drivers/usb/dwc3/gadget.h
+++ b/drivers/usb/dwc3/gadget.h
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#ifndef __DRIVERS_USB_DWC3_GADGET_H
diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
index 0fa1846..32db328 100644
--- a/drivers/usb/dwc3/host.c
+++ b/drivers/usb/dwc3/host.c
@@ -5,34 +5,14 @@
*
* Authors: Felipe Balbi <balbi@ti.com>,
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#include <linux/platform_device.h>
diff --git a/drivers/usb/dwc3/io.h b/drivers/usb/dwc3/io.h
index a50f76b..d94441c 100644
--- a/drivers/usb/dwc3/io.h
+++ b/drivers/usb/dwc3/io.h
@@ -6,34 +6,14 @@
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- * notice, this list of conditions, and the following disclaimer,
- * without modification.
- * 2. Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * 3. The names of the above-listed copyright holders may not be used
- * to endorse or promote products derived from this software without
- * specific prior written permission.
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
*
- * ALTERNATIVELY, this software may be distributed under the terms of the
- * GNU General Public License ("GPL") version 2, as published by the Free
- * Software Foundation.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
- * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
- * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
- * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
- * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
- * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
- * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
- * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
*/
#ifndef __DRIVERS_USB_DWC3_IO_H
diff --git a/drivers/usb/dwc3/platform_data.h b/drivers/usb/dwc3/platform_data.h
new file mode 100644
index 0000000..7db34f0
--- /dev/null
+++ b/drivers/usb/dwc3/platform_data.h
@@ -0,0 +1,27 @@
+/**
+ * platform_data.h - USB DWC3 Platform Data Support
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Author: Felipe Balbi <balbi@ti.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/usb/ch9.h>
+#include <linux/usb/otg.h>
+
+struct dwc3_platform_data {
+ enum usb_device_speed maximum_speed;
+ enum usb_dr_mode dr_mode;
+ bool tx_fifo_resize;
+};
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index 8e93683..1e3f525 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -144,7 +144,6 @@
config USB_LPC32XX
tristate "LPC32XX USB Peripheral Controller"
depends on ARCH_LPC32XX
- depends on USB_PHY
select USB_ISP1301
help
This option selects the USB device controller in the LPC32xx SoC.
@@ -206,7 +205,6 @@
config USB_OMAP
tristate "OMAP USB Device Controller"
depends on ARCH_OMAP1
- depends on USB_PHY
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_H4_OTG
help
Many Texas Instruments OMAP processors have flexible full
@@ -287,21 +285,6 @@
The Samsung S3C64XX USB2.0 high-speed gadget controller
integrated into the S3C64XX series SoC.
-config USB_IMX
- tristate "Freescale i.MX1 USB Peripheral Controller"
- depends on ARCH_MXC
- depends on BROKEN
- help
- Freescale's i.MX1 includes an integrated full speed
- USB 1.1 device controller.
-
- It has Six fixed-function endpoints, as well as endpoint
- zero (for control transfers).
-
- Say "y" to link the driver statically, or "m" to build a
- dynamically linked module called "imx_udc" and force all
- gadget drivers to also be dynamically linked.
-
config USB_S3C2410
tristate "S3C2410 USB Device Controller"
depends on ARCH_S3C24XX
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index bad08e6..386db9d 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -13,7 +13,6 @@
obj-$(CONFIG_USB_AMD5536UDC) += amd5536udc.o
obj-$(CONFIG_USB_PXA25X) += pxa25x_udc.o
obj-$(CONFIG_USB_PXA27X) += pxa27x_udc.o
-obj-$(CONFIG_USB_IMX) += imx_udc.o
obj-$(CONFIG_USB_GOKU) += goku_udc.o
obj-$(CONFIG_USB_OMAP) += omap_udc.o
obj-$(CONFIG_USB_S3C2410) += s3c2410_udc.o
diff --git a/drivers/usb/gadget/amd5536udc.c b/drivers/usb/gadget/amd5536udc.c
index f52dcfe..a9a4346 100644
--- a/drivers/usb/gadget/amd5536udc.c
+++ b/drivers/usb/gadget/amd5536udc.c
@@ -1122,7 +1122,7 @@
goto finished;
}
if (ep->dma) {
- retval = prep_dma(ep, req, gfp);
+ retval = prep_dma(ep, req, GFP_ATOMIC);
if (retval != 0)
goto finished;
/* write desc pointer to enable DMA */
@@ -1190,7 +1190,7 @@
* for PPB modes, because of chain creation reasons
*/
if (ep->in) {
- retval = prep_dma(ep, req, gfp);
+ retval = prep_dma(ep, req, GFP_ATOMIC);
if (retval != 0)
goto finished;
}
diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c
index d9a6add0..4cc4fd6 100644
--- a/drivers/usb/gadget/at91_udc.c
+++ b/drivers/usb/gadget/at91_udc.c
@@ -870,6 +870,11 @@
if (udc->clocked)
return;
udc->clocked = 1;
+
+ if (IS_ENABLED(CONFIG_COMMON_CLK)) {
+ clk_set_rate(udc->uclk, 48000000);
+ clk_prepare_enable(udc->uclk);
+ }
clk_prepare_enable(udc->iclk);
clk_prepare_enable(udc->fclk);
}
@@ -882,6 +887,8 @@
udc->gadget.speed = USB_SPEED_UNKNOWN;
clk_disable_unprepare(udc->fclk);
clk_disable_unprepare(udc->iclk);
+ if (IS_ENABLED(CONFIG_COMMON_CLK))
+ clk_disable_unprepare(udc->uclk);
}
/*
@@ -1697,7 +1704,7 @@
int retval;
struct resource *res;
- if (!dev->platform_data && !pdev->dev.of_node) {
+ if (!dev_get_platdata(dev) && !pdev->dev.of_node) {
/* small (so we copy it) but critical! */
DBG("missing platform_data\n");
return -ENODEV;
@@ -1728,7 +1735,7 @@
if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node)
at91udc_of_init(udc, pdev->dev.of_node);
else
- memcpy(&udc->board, dev->platform_data,
+ memcpy(&udc->board, dev_get_platdata(dev),
sizeof(struct at91_udc_data));
udc->pdev = pdev;
udc->enabled = 0;
@@ -1774,10 +1781,12 @@
/* get interface and function clocks */
udc->iclk = clk_get(dev, "udc_clk");
udc->fclk = clk_get(dev, "udpck");
- if (IS_ERR(udc->iclk) || IS_ERR(udc->fclk)) {
+ if (IS_ENABLED(CONFIG_COMMON_CLK))
+ udc->uclk = clk_get(dev, "usb_clk");
+ if (IS_ERR(udc->iclk) || IS_ERR(udc->fclk) ||
+ (IS_ENABLED(CONFIG_COMMON_CLK) && IS_ERR(udc->uclk))) {
DBG("clocks missing\n");
retval = -ENODEV;
- /* NOTE: we "know" here that refcounts on these are NOPs */
goto fail1;
}
@@ -1851,6 +1860,12 @@
fail2:
free_irq(udc->udp_irq, udc);
fail1:
+ if (IS_ENABLED(CONFIG_COMMON_CLK) && !IS_ERR(udc->uclk))
+ clk_put(udc->uclk);
+ if (!IS_ERR(udc->fclk))
+ clk_put(udc->fclk);
+ if (!IS_ERR(udc->iclk))
+ clk_put(udc->iclk);
iounmap(udc->udp_baseaddr);
fail0a:
if (cpu_is_at91rm9200())
@@ -1894,6 +1909,8 @@
clk_put(udc->iclk);
clk_put(udc->fclk);
+ if (IS_ENABLED(CONFIG_COMMON_CLK))
+ clk_put(udc->uclk);
return 0;
}
diff --git a/drivers/usb/gadget/at91_udc.h b/drivers/usb/gadget/at91_udc.h
index e647d1c..0175246 100644
--- a/drivers/usb/gadget/at91_udc.h
+++ b/drivers/usb/gadget/at91_udc.h
@@ -126,7 +126,7 @@
unsigned active_suspend:1;
u8 addr;
struct at91_udc_data board;
- struct clk *iclk, *fclk;
+ struct clk *iclk, *fclk, *uclk;
struct platform_device *pdev;
struct proc_dir_entry *pde;
void __iomem *udp_baseaddr;
diff --git a/drivers/usb/gadget/atmel_usba_udc.c b/drivers/usb/gadget/atmel_usba_udc.c
index 1d97222..40d2338 100644
--- a/drivers/usb/gadget/atmel_usba_udc.c
+++ b/drivers/usb/gadget/atmel_usba_udc.c
@@ -1772,6 +1772,7 @@
static int atmel_usba_start(struct usb_gadget *gadget,
struct usb_gadget_driver *driver)
{
+ int ret = 0;
struct usba_udc *udc = container_of(gadget, struct usba_udc, gadget);
unsigned long flags;
@@ -1781,8 +1782,14 @@
udc->driver = driver;
spin_unlock_irqrestore(&udc->lock, flags);
- clk_enable(udc->pclk);
- clk_enable(udc->hclk);
+ ret = clk_prepare_enable(udc->pclk);
+ if (ret)
+ goto out;
+ ret = clk_prepare_enable(udc->hclk);
+ if (ret) {
+ clk_disable_unprepare(udc->pclk);
+ goto out;
+ }
DBG(DBG_GADGET, "registered driver `%s'\n", driver->driver.name);
@@ -1797,9 +1804,11 @@
usba_writel(udc, CTRL, USBA_ENABLE_MASK);
usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
}
+
+out:
spin_unlock_irqrestore(&udc->lock, flags);
- return 0;
+ return ret;
}
static int atmel_usba_stop(struct usb_gadget *gadget,
@@ -1822,8 +1831,8 @@
udc->driver = NULL;
- clk_disable(udc->hclk);
- clk_disable(udc->pclk);
+ clk_disable_unprepare(udc->hclk);
+ clk_disable_unprepare(udc->pclk);
DBG(DBG_GADGET, "unregistered driver `%s'\n", driver->driver.name);
@@ -1922,7 +1931,7 @@
static struct usba_ep * usba_udc_pdata(struct platform_device *pdev,
struct usba_udc *udc)
{
- struct usba_platform_data *pdata = pdev->dev.platform_data;
+ struct usba_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct usba_ep *eps;
int i;
@@ -2022,10 +2031,14 @@
platform_set_drvdata(pdev, udc);
/* Make sure we start from a clean slate */
- clk_enable(pclk);
+ ret = clk_prepare_enable(pclk);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to enable pclk, aborting.\n");
+ goto err_clk_enable;
+ }
toggle_bias(0);
usba_writel(udc, CTRL, USBA_DISABLE_MASK);
- clk_disable(pclk);
+ clk_disable_unprepare(pclk);
if (pdev->dev.of_node)
udc->usba_ep = atmel_udc_of_init(pdev, udc);
@@ -2081,6 +2094,7 @@
free_irq(irq, udc);
err_request_irq:
err_alloc_ep:
+err_clk_enable:
iounmap(udc->fifo);
err_map_fifo:
iounmap(udc->regs);
diff --git a/drivers/usb/gadget/bcm63xx_udc.c b/drivers/usb/gadget/bcm63xx_udc.c
index fd24cb4..c58fcf1 100644
--- a/drivers/usb/gadget/bcm63xx_udc.c
+++ b/drivers/usb/gadget/bcm63xx_udc.c
@@ -2313,7 +2313,7 @@
static int bcm63xx_udc_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
- struct bcm63xx_usbd_platform_data *pd = dev->platform_data;
+ struct bcm63xx_usbd_platform_data *pd = dev_get_platdata(dev);
struct bcm63xx_udc *udc;
struct resource *res;
int rc = -ENOMEM, i, irq;
diff --git a/drivers/usb/gadget/f_mass_storage.c b/drivers/usb/gadget/f_mass_storage.c
index 56f1fd1..4d4e96a 100644
--- a/drivers/usb/gadget/f_mass_storage.c
+++ b/drivers/usb/gadget/f_mass_storage.c
@@ -3043,12 +3043,12 @@
lun->filename =
params->file_count > i && params->file[i][0]
? params->file[i]
- : 0;
+ : NULL;
}
/* Let MSF use defaults */
- cfg->vendor_name = 0;
- cfg->product_name = 0;
+ cfg->vendor_name = NULL;
+ cfg->product_name = NULL;
cfg->ops = NULL;
cfg->private_data = NULL;
diff --git a/drivers/usb/gadget/f_uac1.c b/drivers/usb/gadget/f_uac1.c
index fa8ea4e..2b4c82d 100644
--- a/drivers/usb/gadget/f_uac1.c
+++ b/drivers/usb/gadget/f_uac1.c
@@ -695,7 +695,7 @@
}
/* Todo: add more control selecotor dynamically */
-int __init control_selector_init(struct f_audio *audio)
+static int __init control_selector_init(struct f_audio *audio)
{
INIT_LIST_HEAD(&audio->cs);
list_add(&feature_unit.list, &audio->cs);
@@ -719,7 +719,7 @@
*
* Returns zero on success, else negative errno.
*/
-int __init audio_bind_config(struct usb_configuration *c)
+static int __init audio_bind_config(struct usb_configuration *c)
{
struct f_audio *audio;
int status;
diff --git a/drivers/usb/gadget/fsl_mxc_udc.c b/drivers/usb/gadget/fsl_mxc_udc.c
index d3bd7b0..9b140fc 100644
--- a/drivers/usb/gadget/fsl_mxc_udc.c
+++ b/drivers/usb/gadget/fsl_mxc_udc.c
@@ -33,7 +33,7 @@
unsigned long freq;
int ret;
- pdata = pdev->dev.platform_data;
+ pdata = dev_get_platdata(&pdev->dev);
mxc_ipg_clk = devm_clk_get(&pdev->dev, "ipg");
if (IS_ERR(mxc_ipg_clk)) {
@@ -80,7 +80,7 @@
int fsl_udc_clk_finalize(struct platform_device *pdev)
{
- struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
+ struct fsl_usb2_platform_data *pdata = dev_get_platdata(&pdev->dev);
int ret = 0;
/* workaround ENGcm09152 for i.MX35 */
diff --git a/drivers/usb/gadget/fsl_udc_core.c b/drivers/usb/gadget/fsl_udc_core.c
index a766a4c..36ac7cf 100644
--- a/drivers/usb/gadget/fsl_udc_core.c
+++ b/drivers/usb/gadget/fsl_udc_core.c
@@ -2248,7 +2248,7 @@
struct fsl_usb2_platform_data *pdata;
size_t size;
- pdata = pdev->dev.platform_data;
+ pdata = dev_get_platdata(&pdev->dev);
udc->phy_mode = pdata->phy_mode;
udc->eps = kzalloc(sizeof(struct fsl_ep) * udc->max_ep, GFP_KERNEL);
@@ -2343,7 +2343,7 @@
return -ENOMEM;
}
- pdata = pdev->dev.platform_data;
+ pdata = dev_get_platdata(&pdev->dev);
udc_controller->pdata = pdata;
spin_lock_init(&udc_controller->lock);
udc_controller->stopped = 1;
@@ -2524,7 +2524,7 @@
static int __exit fsl_udc_remove(struct platform_device *pdev)
{
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
+ struct fsl_usb2_platform_data *pdata = dev_get_platdata(&pdev->dev);
DECLARE_COMPLETION(done);
diff --git a/drivers/usb/gadget/fusb300_udc.c b/drivers/usb/gadget/fusb300_udc.c
index c83f3e1..f1dd6da 100644
--- a/drivers/usb/gadget/fusb300_udc.c
+++ b/drivers/usb/gadget/fusb300_udc.c
@@ -557,7 +557,7 @@
}
/* read data from cx fifo */
-void fusb300_rdcxf(struct fusb300 *fusb300,
+static void fusb300_rdcxf(struct fusb300 *fusb300,
u8 *buffer, u32 length)
{
int i = 0;
diff --git a/drivers/usb/gadget/goku_udc.c b/drivers/usb/gadget/goku_udc.c
index 52dd6cc..c64deb9 100644
--- a/drivers/usb/gadget/goku_udc.c
+++ b/drivers/usb/gadget/goku_udc.c
@@ -772,7 +772,7 @@
} /* else pio or dma irq handler advances the queue. */
- if (likely(req != 0))
+ if (likely(req != NULL))
list_add_tail(&req->queue, &ep->queue);
if (likely(!list_empty(&ep->queue))
diff --git a/drivers/usb/gadget/hid.c b/drivers/usb/gadget/hid.c
index c36260ea..778613eb 100644
--- a/drivers/usb/gadget/hid.c
+++ b/drivers/usb/gadget/hid.c
@@ -185,7 +185,7 @@
static int __init hidg_plat_driver_probe(struct platform_device *pdev)
{
- struct hidg_func_descriptor *func = pdev->dev.platform_data;
+ struct hidg_func_descriptor *func = dev_get_platdata(&pdev->dev);
struct hidg_func_node *entry;
if (!func) {
diff --git a/drivers/usb/gadget/imx_udc.c b/drivers/usb/gadget/imx_udc.c
deleted file mode 100644
index 9b2d24e..0000000
--- a/drivers/usb/gadget/imx_udc.c
+++ /dev/null
@@ -1,1544 +0,0 @@
-/*
- * driver/usb/gadget/imx_udc.c
- *
- * Copyright (C) 2005 Mike Lee <eemike@gmail.com>
- * Copyright (C) 2008 Darius Augulis <augulis.darius@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/list.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/device.h>
-#include <linux/dma-mapping.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/slab.h>
-#include <linux/prefetch.h>
-
-#include <linux/usb/ch9.h>
-#include <linux/usb/gadget.h>
-
-#include <linux/platform_data/usb-imx_udc.h>
-#include <mach/hardware.h>
-
-#include "imx_udc.h"
-
-static const char driver_name[] = "imx_udc";
-static const char ep0name[] = "ep0";
-
-void ep0_chg_stat(const char *label, struct imx_udc_struct *imx_usb,
- enum ep0_state stat);
-
-/*******************************************************************************
- * IMX UDC hardware related functions
- *******************************************************************************
- */
-
-void imx_udc_enable(struct imx_udc_struct *imx_usb)
-{
- int temp = __raw_readl(imx_usb->base + USB_CTRL);
- __raw_writel(temp | CTRL_FE_ENA | CTRL_AFE_ENA,
- imx_usb->base + USB_CTRL);
- imx_usb->gadget.speed = USB_SPEED_FULL;
-}
-
-void imx_udc_disable(struct imx_udc_struct *imx_usb)
-{
- int temp = __raw_readl(imx_usb->base + USB_CTRL);
-
- __raw_writel(temp & ~(CTRL_FE_ENA | CTRL_AFE_ENA),
- imx_usb->base + USB_CTRL);
-
- ep0_chg_stat(__func__, imx_usb, EP0_IDLE);
- imx_usb->gadget.speed = USB_SPEED_UNKNOWN;
-}
-
-void imx_udc_reset(struct imx_udc_struct *imx_usb)
-{
- int temp = __raw_readl(imx_usb->base + USB_ENAB);
-
- /* set RST bit */
- __raw_writel(temp | ENAB_RST, imx_usb->base + USB_ENAB);
-
- /* wait RST bit to clear */
- do {} while (__raw_readl(imx_usb->base + USB_ENAB) & ENAB_RST);
-
- /* wait CFG bit to assert */
- do {} while (!(__raw_readl(imx_usb->base + USB_DADR) & DADR_CFG));
-
- /* udc module is now ready */
-}
-
-void imx_udc_config(struct imx_udc_struct *imx_usb)
-{
- u8 ep_conf[5];
- u8 i, j, cfg;
- struct imx_ep_struct *imx_ep;
-
- /* wait CFG bit to assert */
- do {} while (!(__raw_readl(imx_usb->base + USB_DADR) & DADR_CFG));
-
- /* Download the endpoint buffer for endpoint 0. */
- for (j = 0; j < 5; j++) {
- i = (j == 2 ? imx_usb->imx_ep[0].fifosize : 0x00);
- __raw_writeb(i, imx_usb->base + USB_DDAT);
- do {} while (__raw_readl(imx_usb->base + USB_DADR) & DADR_BSY);
- }
-
- /* Download the endpoint buffers for endpoints 1-5.
- * We specify two configurations, one interface
- */
- for (cfg = 1; cfg < 3; cfg++) {
- for (i = 1; i < IMX_USB_NB_EP; i++) {
- imx_ep = &imx_usb->imx_ep[i];
- /* EP no | Config no */
- ep_conf[0] = (i << 4) | (cfg << 2);
- /* Type | Direction */
- ep_conf[1] = (imx_ep->bmAttributes << 3) |
- (EP_DIR(imx_ep) << 2);
- /* Max packet size */
- ep_conf[2] = imx_ep->fifosize;
- /* TRXTYP */
- ep_conf[3] = 0xC0;
- /* FIFO no */
- ep_conf[4] = i;
-
- D_INI(imx_usb->dev,
- "<%s> ep%d_conf[%d]:"
- "[%02x-%02x-%02x-%02x-%02x]\n",
- __func__, i, cfg,
- ep_conf[0], ep_conf[1], ep_conf[2],
- ep_conf[3], ep_conf[4]);
-
- for (j = 0; j < 5; j++) {
- __raw_writeb(ep_conf[j],
- imx_usb->base + USB_DDAT);
- do {} while (__raw_readl(imx_usb->base
- + USB_DADR)
- & DADR_BSY);
- }
- }
- }
-
- /* wait CFG bit to clear */
- do {} while (__raw_readl(imx_usb->base + USB_DADR) & DADR_CFG);
-}
-
-void imx_udc_init_irq(struct imx_udc_struct *imx_usb)
-{
- int i;
-
- /* Mask and clear all irqs */
- __raw_writel(0xFFFFFFFF, imx_usb->base + USB_MASK);
- __raw_writel(0xFFFFFFFF, imx_usb->base + USB_INTR);
- for (i = 0; i < IMX_USB_NB_EP; i++) {
- __raw_writel(0x1FF, imx_usb->base + USB_EP_MASK(i));
- __raw_writel(0x1FF, imx_usb->base + USB_EP_INTR(i));
- }
-
- /* Enable USB irqs */
- __raw_writel(INTR_MSOF | INTR_FRAME_MATCH, imx_usb->base + USB_MASK);
-
- /* Enable EP0 irqs */
- __raw_writel(0x1FF & ~(EPINTR_DEVREQ | EPINTR_MDEVREQ | EPINTR_EOT
- | EPINTR_EOF | EPINTR_FIFO_EMPTY | EPINTR_FIFO_FULL),
- imx_usb->base + USB_EP_MASK(0));
-}
-
-void imx_udc_init_ep(struct imx_udc_struct *imx_usb)
-{
- int i, max, temp;
- struct imx_ep_struct *imx_ep;
- for (i = 0; i < IMX_USB_NB_EP; i++) {
- imx_ep = &imx_usb->imx_ep[i];
- switch (imx_ep->fifosize) {
- case 8:
- max = 0;
- break;
- case 16:
- max = 1;
- break;
- case 32:
- max = 2;
- break;
- case 64:
- max = 3;
- break;
- default:
- max = 1;
- break;
- }
- temp = (EP_DIR(imx_ep) << 7) | (max << 5)
- | (imx_ep->bmAttributes << 3);
- __raw_writel(temp, imx_usb->base + USB_EP_STAT(i));
- __raw_writel(temp | EPSTAT_FLUSH,
- imx_usb->base + USB_EP_STAT(i));
- D_INI(imx_usb->dev, "<%s> ep%d_stat %08x\n", __func__, i,
- __raw_readl(imx_usb->base + USB_EP_STAT(i)));
- }
-}
-
-void imx_udc_init_fifo(struct imx_udc_struct *imx_usb)
-{
- int i, temp;
- struct imx_ep_struct *imx_ep;
- for (i = 0; i < IMX_USB_NB_EP; i++) {
- imx_ep = &imx_usb->imx_ep[i];
-
- /* Fifo control */
- temp = EP_DIR(imx_ep) ? 0x0B000000 : 0x0F000000;
- __raw_writel(temp, imx_usb->base + USB_EP_FCTRL(i));
- D_INI(imx_usb->dev, "<%s> ep%d_fctrl %08x\n", __func__, i,
- __raw_readl(imx_usb->base + USB_EP_FCTRL(i)));
-
- /* Fifo alarm */
- temp = (i ? imx_ep->fifosize / 2 : 0);
- __raw_writel(temp, imx_usb->base + USB_EP_FALRM(i));
- D_INI(imx_usb->dev, "<%s> ep%d_falrm %08x\n", __func__, i,
- __raw_readl(imx_usb->base + USB_EP_FALRM(i)));
- }
-}
-
-static void imx_udc_init(struct imx_udc_struct *imx_usb)
-{
- /* Reset UDC */
- imx_udc_reset(imx_usb);
-
- /* Download config to enpoint buffer */
- imx_udc_config(imx_usb);
-
- /* Setup interrups */
- imx_udc_init_irq(imx_usb);
-
- /* Setup endpoints */
- imx_udc_init_ep(imx_usb);
-
- /* Setup fifos */
- imx_udc_init_fifo(imx_usb);
-}
-
-void imx_ep_irq_enable(struct imx_ep_struct *imx_ep)
-{
-
- int i = EP_NO(imx_ep);
-
- __raw_writel(0x1FF, imx_ep->imx_usb->base + USB_EP_MASK(i));
- __raw_writel(0x1FF, imx_ep->imx_usb->base + USB_EP_INTR(i));
- __raw_writel(0x1FF & ~(EPINTR_EOT | EPINTR_EOF),
- imx_ep->imx_usb->base + USB_EP_MASK(i));
-}
-
-void imx_ep_irq_disable(struct imx_ep_struct *imx_ep)
-{
-
- int i = EP_NO(imx_ep);
-
- __raw_writel(0x1FF, imx_ep->imx_usb->base + USB_EP_MASK(i));
- __raw_writel(0x1FF, imx_ep->imx_usb->base + USB_EP_INTR(i));
-}
-
-int imx_ep_empty(struct imx_ep_struct *imx_ep)
-{
- struct imx_udc_struct *imx_usb = imx_ep->imx_usb;
-
- return __raw_readl(imx_usb->base + USB_EP_FSTAT(EP_NO(imx_ep)))
- & FSTAT_EMPTY;
-}
-
-unsigned imx_fifo_bcount(struct imx_ep_struct *imx_ep)
-{
- struct imx_udc_struct *imx_usb = imx_ep->imx_usb;
-
- return (__raw_readl(imx_usb->base + USB_EP_STAT(EP_NO(imx_ep)))
- & EPSTAT_BCOUNT) >> 16;
-}
-
-void imx_flush(struct imx_ep_struct *imx_ep)
-{
- struct imx_udc_struct *imx_usb = imx_ep->imx_usb;
-
- int temp = __raw_readl(imx_usb->base + USB_EP_STAT(EP_NO(imx_ep)));
- __raw_writel(temp | EPSTAT_FLUSH,
- imx_usb->base + USB_EP_STAT(EP_NO(imx_ep)));
-}
-
-void imx_ep_stall(struct imx_ep_struct *imx_ep)
-{
- struct imx_udc_struct *imx_usb = imx_ep->imx_usb;
- int temp, i;
-
- D_ERR(imx_usb->dev,
- "<%s> Forced stall on %s\n", __func__, imx_ep->ep.name);
-
- imx_flush(imx_ep);
-
- /* Special care for ep0 */
- if (!EP_NO(imx_ep)) {
- temp = __raw_readl(imx_usb->base + USB_CTRL);
- __raw_writel(temp | CTRL_CMDOVER | CTRL_CMDERROR,
- imx_usb->base + USB_CTRL);
- do { } while (__raw_readl(imx_usb->base + USB_CTRL)
- & CTRL_CMDOVER);
- temp = __raw_readl(imx_usb->base + USB_CTRL);
- __raw_writel(temp & ~CTRL_CMDERROR, imx_usb->base + USB_CTRL);
- }
- else {
- temp = __raw_readl(imx_usb->base + USB_EP_STAT(EP_NO(imx_ep)));
- __raw_writel(temp | EPSTAT_STALL,
- imx_usb->base + USB_EP_STAT(EP_NO(imx_ep)));
-
- for (i = 0; i < 100; i ++) {
- temp = __raw_readl(imx_usb->base
- + USB_EP_STAT(EP_NO(imx_ep)));
- if (!(temp & EPSTAT_STALL))
- break;
- udelay(20);
- }
- if (i == 100)
- D_ERR(imx_usb->dev, "<%s> Non finished stall on %s\n",
- __func__, imx_ep->ep.name);
- }
-}
-
-static int imx_udc_get_frame(struct usb_gadget *_gadget)
-{
- struct imx_udc_struct *imx_usb = container_of(_gadget,
- struct imx_udc_struct, gadget);
-
- return __raw_readl(imx_usb->base + USB_FRAME) & 0x7FF;
-}
-
-static int imx_udc_wakeup(struct usb_gadget *_gadget)
-{
- return 0;
-}
-
-/*******************************************************************************
- * USB request control functions
- *******************************************************************************
- */
-
-static void ep_add_request(struct imx_ep_struct *imx_ep,
- struct imx_request *req)
-{
- if (unlikely(!req))
- return;
-
- req->in_use = 1;
- list_add_tail(&req->queue, &imx_ep->queue);
-}
-
-static void ep_del_request(struct imx_ep_struct *imx_ep,
- struct imx_request *req)
-{
- if (unlikely(!req))
- return;
-
- list_del_init(&req->queue);
- req->in_use = 0;
-}
-
-static void done(struct imx_ep_struct *imx_ep,
- struct imx_request *req, int status)
-{
- ep_del_request(imx_ep, req);
-
- if (likely(req->req.status == -EINPROGRESS))
- req->req.status = status;
- else
- status = req->req.status;
-
- if (status && status != -ESHUTDOWN)
- D_ERR(imx_ep->imx_usb->dev,
- "<%s> complete %s req %p stat %d len %u/%u\n", __func__,
- imx_ep->ep.name, &req->req, status,
- req->req.actual, req->req.length);
-
- req->req.complete(&imx_ep->ep, &req->req);
-}
-
-static void nuke(struct imx_ep_struct *imx_ep, int status)
-{
- struct imx_request *req;
-
- while (!list_empty(&imx_ep->queue)) {
- req = list_entry(imx_ep->queue.next, struct imx_request, queue);
- done(imx_ep, req, status);
- }
-}
-
-/*******************************************************************************
- * Data tansfer over USB functions
- *******************************************************************************
- */
-static int read_packet(struct imx_ep_struct *imx_ep, struct imx_request *req)
-{
- u8 *buf;
- int bytes_ep, bufferspace, count, i;
-
- bytes_ep = imx_fifo_bcount(imx_ep);
- bufferspace = req->req.length - req->req.actual;
-
- buf = req->req.buf + req->req.actual;
- prefetchw(buf);
-
- if (unlikely(imx_ep_empty(imx_ep)))
- count = 0; /* zlp */
- else
- count = min(bytes_ep, bufferspace);
-
- for (i = count; i > 0; i--)
- *buf++ = __raw_readb(imx_ep->imx_usb->base
- + USB_EP_FDAT0(EP_NO(imx_ep)));
- req->req.actual += count;
-
- return count;
-}
-
-static int write_packet(struct imx_ep_struct *imx_ep, struct imx_request *req)
-{
- u8 *buf;
- int length, count, temp;
-
- if (unlikely(__raw_readl(imx_ep->imx_usb->base +
- USB_EP_STAT(EP_NO(imx_ep))) & EPSTAT_ZLPS)) {
- D_TRX(imx_ep->imx_usb->dev, "<%s> zlp still queued in EP %s\n",
- __func__, imx_ep->ep.name);
- return -1;
- }
-
- buf = req->req.buf + req->req.actual;
- prefetch(buf);
-
- length = min(req->req.length - req->req.actual, (u32)imx_ep->fifosize);
-
- if (imx_fifo_bcount(imx_ep) + length > imx_ep->fifosize) {
- D_TRX(imx_ep->imx_usb->dev, "<%s> packet overfill %s fifo\n",
- __func__, imx_ep->ep.name);
- return -1;
- }
-
- req->req.actual += length;
- count = length;
-
- if (!count && req->req.zero) { /* zlp */
- temp = __raw_readl(imx_ep->imx_usb->base
- + USB_EP_STAT(EP_NO(imx_ep)));
- __raw_writel(temp | EPSTAT_ZLPS, imx_ep->imx_usb->base
- + USB_EP_STAT(EP_NO(imx_ep)));
- D_TRX(imx_ep->imx_usb->dev, "<%s> zero packet\n", __func__);
- return 0;
- }
-
- while (count--) {
- if (count == 0) { /* last byte */
- temp = __raw_readl(imx_ep->imx_usb->base
- + USB_EP_FCTRL(EP_NO(imx_ep)));
- __raw_writel(temp | FCTRL_WFR, imx_ep->imx_usb->base
- + USB_EP_FCTRL(EP_NO(imx_ep)));
- }
- __raw_writeb(*buf++,
- imx_ep->imx_usb->base + USB_EP_FDAT0(EP_NO(imx_ep)));
- }
-
- return length;
-}
-
-static int read_fifo(struct imx_ep_struct *imx_ep, struct imx_request *req)
-{
- int bytes = 0,
- count,
- completed = 0;
-
- while (__raw_readl(imx_ep->imx_usb->base + USB_EP_FSTAT(EP_NO(imx_ep)))
- & FSTAT_FR) {
- count = read_packet(imx_ep, req);
- bytes += count;
-
- completed = (count != imx_ep->fifosize);
- if (completed || req->req.actual == req->req.length) {
- completed = 1;
- break;
- }
- }
-
- if (completed || !req->req.length) {
- done(imx_ep, req, 0);
- D_REQ(imx_ep->imx_usb->dev, "<%s> %s req<%p> %s\n",
- __func__, imx_ep->ep.name, req,
- completed ? "completed" : "not completed");
- if (!EP_NO(imx_ep))
- ep0_chg_stat(__func__, imx_ep->imx_usb, EP0_IDLE);
- }
-
- D_TRX(imx_ep->imx_usb->dev, "<%s> bytes read: %d\n", __func__, bytes);
-
- return completed;
-}
-
-static int write_fifo(struct imx_ep_struct *imx_ep, struct imx_request *req)
-{
- int bytes = 0,
- count,
- completed = 0;
-
- while (!completed) {
- count = write_packet(imx_ep, req);
- if (count < 0)
- break; /* busy */
- bytes += count;
-
- /* last packet "must be" short (or a zlp) */
- completed = (count != imx_ep->fifosize);
-
- if (unlikely(completed)) {
- done(imx_ep, req, 0);
- D_REQ(imx_ep->imx_usb->dev, "<%s> %s req<%p> %s\n",
- __func__, imx_ep->ep.name, req,
- completed ? "completed" : "not completed");
- if (!EP_NO(imx_ep))
- ep0_chg_stat(__func__,
- imx_ep->imx_usb, EP0_IDLE);
- }
- }
-
- D_TRX(imx_ep->imx_usb->dev, "<%s> bytes sent: %d\n", __func__, bytes);
-
- return completed;
-}
-
-/*******************************************************************************
- * Endpoint handlers
- *******************************************************************************
- */
-static int handle_ep(struct imx_ep_struct *imx_ep)
-{
- struct imx_request *req;
- int completed = 0;
-
- do {
- if (!list_empty(&imx_ep->queue))
- req = list_entry(imx_ep->queue.next,
- struct imx_request, queue);
- else {
- D_REQ(imx_ep->imx_usb->dev, "<%s> no request on %s\n",
- __func__, imx_ep->ep.name);
- return 0;
- }
-
- if (EP_DIR(imx_ep)) /* to host */
- completed = write_fifo(imx_ep, req);
- else /* to device */
- completed = read_fifo(imx_ep, req);
-
- dump_ep_stat(__func__, imx_ep);
-
- } while (completed);
-
- return 0;
-}
-
-static int handle_ep0(struct imx_ep_struct *imx_ep)
-{
- struct imx_request *req = NULL;
- int ret = 0;
-
- if (!list_empty(&imx_ep->queue)) {
- req = list_entry(imx_ep->queue.next, struct imx_request, queue);
-
- switch (imx_ep->imx_usb->ep0state) {
-
- case EP0_IN_DATA_PHASE: /* GET_DESCRIPTOR */
- write_fifo(imx_ep, req);
- break;
- case EP0_OUT_DATA_PHASE: /* SET_DESCRIPTOR */
- read_fifo(imx_ep, req);
- break;
- default:
- D_EP0(imx_ep->imx_usb->dev,
- "<%s> ep0 i/o, odd state %d\n",
- __func__, imx_ep->imx_usb->ep0state);
- ep_del_request(imx_ep, req);
- ret = -EL2HLT;
- break;
- }
- }
-
- else
- D_ERR(imx_ep->imx_usb->dev, "<%s> no request on %s\n",
- __func__, imx_ep->ep.name);
-
- return ret;
-}
-
-static void handle_ep0_devreq(struct imx_udc_struct *imx_usb)
-{
- struct imx_ep_struct *imx_ep = &imx_usb->imx_ep[0];
- union {
- struct usb_ctrlrequest r;
- u8 raw[8];
- u32 word[2];
- } u;
- int temp, i;
-
- nuke(imx_ep, -EPROTO);
-
- /* read SETUP packet */
- for (i = 0; i < 2; i++) {
- if (imx_ep_empty(imx_ep)) {
- D_ERR(imx_usb->dev,
- "<%s> no setup packet received\n", __func__);
- goto stall;
- }
- u.word[i] = __raw_readl(imx_usb->base
- + USB_EP_FDAT(EP_NO(imx_ep)));
- }
-
- temp = imx_ep_empty(imx_ep);
- while (!imx_ep_empty(imx_ep)) {
- i = __raw_readl(imx_usb->base + USB_EP_FDAT(EP_NO(imx_ep)));
- D_ERR(imx_usb->dev,
- "<%s> wrong to have extra bytes for setup : 0x%08x\n",
- __func__, i);
- }
- if (!temp)
- goto stall;
-
- le16_to_cpus(&u.r.wValue);
- le16_to_cpus(&u.r.wIndex);
- le16_to_cpus(&u.r.wLength);
-
- D_REQ(imx_usb->dev, "<%s> SETUP %02x.%02x v%04x i%04x l%04x\n",
- __func__, u.r.bRequestType, u.r.bRequest,
- u.r.wValue, u.r.wIndex, u.r.wLength);
-
- if (imx_usb->set_config) {
- /* NACK the host by using CMDOVER */
- temp = __raw_readl(imx_usb->base + USB_CTRL);
- __raw_writel(temp | CTRL_CMDOVER, imx_usb->base + USB_CTRL);
-
- D_ERR(imx_usb->dev,
- "<%s> set config req is pending, NACK the host\n",
- __func__);
- return;
- }
-
- if (u.r.bRequestType & USB_DIR_IN)
- ep0_chg_stat(__func__, imx_usb, EP0_IN_DATA_PHASE);
- else
- ep0_chg_stat(__func__, imx_usb, EP0_OUT_DATA_PHASE);
-
- i = imx_usb->driver->setup(&imx_usb->gadget, &u.r);
- if (i < 0) {
- D_ERR(imx_usb->dev, "<%s> device setup error %d\n",
- __func__, i);
- goto stall;
- }
-
- return;
-stall:
- D_ERR(imx_usb->dev, "<%s> protocol STALL\n", __func__);
- imx_ep_stall(imx_ep);
- ep0_chg_stat(__func__, imx_usb, EP0_STALL);
- return;
-}
-
-/*******************************************************************************
- * USB gadget callback functions
- *******************************************************************************
- */
-
-static int imx_ep_enable(struct usb_ep *usb_ep,
- const struct usb_endpoint_descriptor *desc)
-{
- struct imx_ep_struct *imx_ep = container_of(usb_ep,
- struct imx_ep_struct, ep);
- struct imx_udc_struct *imx_usb = imx_ep->imx_usb;
- unsigned long flags;
-
- if (!usb_ep
- || !desc
- || !EP_NO(imx_ep)
- || desc->bDescriptorType != USB_DT_ENDPOINT
- || imx_ep->bEndpointAddress != desc->bEndpointAddress) {
- D_ERR(imx_usb->dev,
- "<%s> bad ep or descriptor\n", __func__);
- return -EINVAL;
- }
-
- if (imx_ep->bmAttributes != desc->bmAttributes) {
- D_ERR(imx_usb->dev,
- "<%s> %s type mismatch\n", __func__, usb_ep->name);
- return -EINVAL;
- }
-
- if (imx_ep->fifosize < usb_endpoint_maxp(desc)) {
- D_ERR(imx_usb->dev,
- "<%s> bad %s maxpacket\n", __func__, usb_ep->name);
- return -ERANGE;
- }
-
- if (!imx_usb->driver || imx_usb->gadget.speed == USB_SPEED_UNKNOWN) {
- D_ERR(imx_usb->dev, "<%s> bogus device state\n", __func__);
- return -ESHUTDOWN;
- }
-
- local_irq_save(flags);
-
- imx_ep->stopped = 0;
- imx_flush(imx_ep);
- imx_ep_irq_enable(imx_ep);
-
- local_irq_restore(flags);
-
- D_EPX(imx_usb->dev, "<%s> ENABLED %s\n", __func__, usb_ep->name);
- return 0;
-}
-
-static int imx_ep_disable(struct usb_ep *usb_ep)
-{
- struct imx_ep_struct *imx_ep = container_of(usb_ep,
- struct imx_ep_struct, ep);
- unsigned long flags;
-
- if (!usb_ep || !EP_NO(imx_ep) || !list_empty(&imx_ep->queue)) {
- D_ERR(imx_ep->imx_usb->dev, "<%s> %s can not be disabled\n",
- __func__, usb_ep ? imx_ep->ep.name : NULL);
- return -EINVAL;
- }
-
- local_irq_save(flags);
-
- imx_ep->stopped = 1;
- nuke(imx_ep, -ESHUTDOWN);
- imx_flush(imx_ep);
- imx_ep_irq_disable(imx_ep);
-
- local_irq_restore(flags);
-
- D_EPX(imx_ep->imx_usb->dev,
- "<%s> DISABLED %s\n", __func__, usb_ep->name);
- return 0;
-}
-
-static struct usb_request *imx_ep_alloc_request
- (struct usb_ep *usb_ep, gfp_t gfp_flags)
-{
- struct imx_request *req;
-
- if (!usb_ep)
- return NULL;
-
- req = kzalloc(sizeof *req, gfp_flags);
- if (!req)
- return NULL;
-
- INIT_LIST_HEAD(&req->queue);
- req->in_use = 0;
-
- return &req->req;
-}
-
-static void imx_ep_free_request
- (struct usb_ep *usb_ep, struct usb_request *usb_req)
-{
- struct imx_request *req;
-
- req = container_of(usb_req, struct imx_request, req);
- WARN_ON(!list_empty(&req->queue));
- kfree(req);
-}
-
-static int imx_ep_queue
- (struct usb_ep *usb_ep, struct usb_request *usb_req, gfp_t gfp_flags)
-{
- struct imx_ep_struct *imx_ep;
- struct imx_udc_struct *imx_usb;
- struct imx_request *req;
- unsigned long flags;
- int ret = 0;
-
- imx_ep = container_of(usb_ep, struct imx_ep_struct, ep);
- imx_usb = imx_ep->imx_usb;
- req = container_of(usb_req, struct imx_request, req);
-
- /*
- Special care on IMX udc.
- Ignore enqueue when after set configuration from the
- host. This assume all gadget drivers reply set
- configuration with the next ep0 req enqueue.
- */
- if (imx_usb->set_config && !EP_NO(imx_ep)) {
- imx_usb->set_config = 0;
- D_ERR(imx_usb->dev,
- "<%s> gadget reply set config\n", __func__);
- return 0;
- }
-
- if (unlikely(!usb_req || !req || !usb_req->complete || !usb_req->buf)) {
- D_ERR(imx_usb->dev, "<%s> bad params\n", __func__);
- return -EINVAL;
- }
-
- if (unlikely(!usb_ep || !imx_ep)) {
- D_ERR(imx_usb->dev, "<%s> bad ep\n", __func__);
- return -EINVAL;
- }
-
- if (!imx_usb->driver || imx_usb->gadget.speed == USB_SPEED_UNKNOWN) {
- D_ERR(imx_usb->dev, "<%s> bogus device state\n", __func__);
- return -ESHUTDOWN;
- }
-
- /* Debug */
- D_REQ(imx_usb->dev, "<%s> ep%d %s request for [%d] bytes\n",
- __func__, EP_NO(imx_ep),
- ((!EP_NO(imx_ep) && imx_ep->imx_usb->ep0state
- == EP0_IN_DATA_PHASE)
- || (EP_NO(imx_ep) && EP_DIR(imx_ep)))
- ? "IN" : "OUT", usb_req->length);
- dump_req(__func__, imx_ep, usb_req);
-
- if (imx_ep->stopped) {
- usb_req->status = -ESHUTDOWN;
- return -ESHUTDOWN;
- }
-
- if (req->in_use) {
- D_ERR(imx_usb->dev,
- "<%s> refusing to queue req %p (already queued)\n",
- __func__, req);
- return 0;
- }
-
- local_irq_save(flags);
-
- usb_req->status = -EINPROGRESS;
- usb_req->actual = 0;
-
- ep_add_request(imx_ep, req);
-
- if (!EP_NO(imx_ep))
- ret = handle_ep0(imx_ep);
- else
- ret = handle_ep(imx_ep);
-
- local_irq_restore(flags);
- return ret;
-}
-
-static int imx_ep_dequeue(struct usb_ep *usb_ep, struct usb_request *usb_req)
-{
-
- struct imx_ep_struct *imx_ep = container_of
- (usb_ep, struct imx_ep_struct, ep);
- struct imx_request *req;
- unsigned long flags;
-
- if (unlikely(!usb_ep || !EP_NO(imx_ep))) {
- D_ERR(imx_ep->imx_usb->dev, "<%s> bad ep\n", __func__);
- return -EINVAL;
- }
-
- local_irq_save(flags);
-
- /* make sure it's actually queued on this endpoint */
- list_for_each_entry(req, &imx_ep->queue, queue) {
- if (&req->req == usb_req)
- break;
- }
- if (&req->req != usb_req) {
- local_irq_restore(flags);
- return -EINVAL;
- }
-
- done(imx_ep, req, -ECONNRESET);
-
- local_irq_restore(flags);
- return 0;
-}
-
-static int imx_ep_set_halt(struct usb_ep *usb_ep, int value)
-{
- struct imx_ep_struct *imx_ep = container_of
- (usb_ep, struct imx_ep_struct, ep);
- unsigned long flags;
-
- if (unlikely(!usb_ep || !EP_NO(imx_ep))) {
- D_ERR(imx_ep->imx_usb->dev, "<%s> bad ep\n", __func__);
- return -EINVAL;
- }
-
- local_irq_save(flags);
-
- if ((imx_ep->bEndpointAddress & USB_DIR_IN)
- && !list_empty(&imx_ep->queue)) {
- local_irq_restore(flags);
- return -EAGAIN;
- }
-
- imx_ep_stall(imx_ep);
-
- local_irq_restore(flags);
-
- D_EPX(imx_ep->imx_usb->dev, "<%s> %s halt\n", __func__, usb_ep->name);
- return 0;
-}
-
-static int imx_ep_fifo_status(struct usb_ep *usb_ep)
-{
- struct imx_ep_struct *imx_ep = container_of
- (usb_ep, struct imx_ep_struct, ep);
-
- if (!usb_ep) {
- D_ERR(imx_ep->imx_usb->dev, "<%s> bad ep\n", __func__);
- return -ENODEV;
- }
-
- if (imx_ep->imx_usb->gadget.speed == USB_SPEED_UNKNOWN)
- return 0;
- else
- return imx_fifo_bcount(imx_ep);
-}
-
-static void imx_ep_fifo_flush(struct usb_ep *usb_ep)
-{
- struct imx_ep_struct *imx_ep = container_of
- (usb_ep, struct imx_ep_struct, ep);
- unsigned long flags;
-
- local_irq_save(flags);
-
- if (!usb_ep || !EP_NO(imx_ep) || !list_empty(&imx_ep->queue)) {
- D_ERR(imx_ep->imx_usb->dev, "<%s> bad ep\n", __func__);
- local_irq_restore(flags);
- return;
- }
-
- /* toggle and halt bits stay unchanged */
- imx_flush(imx_ep);
-
- local_irq_restore(flags);
-}
-
-static struct usb_ep_ops imx_ep_ops = {
- .enable = imx_ep_enable,
- .disable = imx_ep_disable,
-
- .alloc_request = imx_ep_alloc_request,
- .free_request = imx_ep_free_request,
-
- .queue = imx_ep_queue,
- .dequeue = imx_ep_dequeue,
-
- .set_halt = imx_ep_set_halt,
- .fifo_status = imx_ep_fifo_status,
- .fifo_flush = imx_ep_fifo_flush,
-};
-
-/*******************************************************************************
- * USB endpoint control functions
- *******************************************************************************
- */
-
-void ep0_chg_stat(const char *label,
- struct imx_udc_struct *imx_usb, enum ep0_state stat)
-{
- D_EP0(imx_usb->dev, "<%s> from %15s to %15s\n",
- label, state_name[imx_usb->ep0state], state_name[stat]);
-
- if (imx_usb->ep0state == stat)
- return;
-
- imx_usb->ep0state = stat;
-}
-
-static void usb_init_data(struct imx_udc_struct *imx_usb)
-{
- struct imx_ep_struct *imx_ep;
- u8 i;
-
- /* device/ep0 records init */
- INIT_LIST_HEAD(&imx_usb->gadget.ep_list);
- INIT_LIST_HEAD(&imx_usb->gadget.ep0->ep_list);
- ep0_chg_stat(__func__, imx_usb, EP0_IDLE);
-
- /* basic endpoint records init */
- for (i = 0; i < IMX_USB_NB_EP; i++) {
- imx_ep = &imx_usb->imx_ep[i];
-
- if (i) {
- list_add_tail(&imx_ep->ep.ep_list,
- &imx_usb->gadget.ep_list);
- imx_ep->stopped = 1;
- } else
- imx_ep->stopped = 0;
-
- INIT_LIST_HEAD(&imx_ep->queue);
- }
-}
-
-static void udc_stop_activity(struct imx_udc_struct *imx_usb,
- struct usb_gadget_driver *driver)
-{
- struct imx_ep_struct *imx_ep;
- int i;
-
- if (imx_usb->gadget.speed == USB_SPEED_UNKNOWN)
- driver = NULL;
-
- /* prevent new request submissions, kill any outstanding requests */
- for (i = 1; i < IMX_USB_NB_EP; i++) {
- imx_ep = &imx_usb->imx_ep[i];
- imx_flush(imx_ep);
- imx_ep->stopped = 1;
- imx_ep_irq_disable(imx_ep);
- nuke(imx_ep, -ESHUTDOWN);
- }
-
- imx_usb->cfg = 0;
- imx_usb->intf = 0;
- imx_usb->alt = 0;
-
- if (driver)
- driver->disconnect(&imx_usb->gadget);
-}
-
-/*******************************************************************************
- * Interrupt handlers
- *******************************************************************************
- */
-
-/*
- * Called when timer expires.
- * Timer is started when CFG_CHG is received.
- */
-static void handle_config(unsigned long data)
-{
- struct imx_udc_struct *imx_usb = (void *)data;
- struct usb_ctrlrequest u;
- int temp, cfg, intf, alt;
-
- local_irq_disable();
-
- temp = __raw_readl(imx_usb->base + USB_STAT);
- cfg = (temp & STAT_CFG) >> 5;
- intf = (temp & STAT_INTF) >> 3;
- alt = temp & STAT_ALTSET;
-
- D_REQ(imx_usb->dev,
- "<%s> orig config C=%d, I=%d, A=%d / "
- "req config C=%d, I=%d, A=%d\n",
- __func__, imx_usb->cfg, imx_usb->intf, imx_usb->alt,
- cfg, intf, alt);
-
- if (cfg == 1 || cfg == 2) {
-
- if (imx_usb->cfg != cfg) {
- u.bRequest = USB_REQ_SET_CONFIGURATION;
- u.bRequestType = USB_DIR_OUT |
- USB_TYPE_STANDARD |
- USB_RECIP_DEVICE;
- u.wValue = cfg;
- u.wIndex = 0;
- u.wLength = 0;
- imx_usb->cfg = cfg;
- imx_usb->driver->setup(&imx_usb->gadget, &u);
-
- }
- if (imx_usb->intf != intf || imx_usb->alt != alt) {
- u.bRequest = USB_REQ_SET_INTERFACE;
- u.bRequestType = USB_DIR_OUT |
- USB_TYPE_STANDARD |
- USB_RECIP_INTERFACE;
- u.wValue = alt;
- u.wIndex = intf;
- u.wLength = 0;
- imx_usb->intf = intf;
- imx_usb->alt = alt;
- imx_usb->driver->setup(&imx_usb->gadget, &u);
- }
- }
-
- imx_usb->set_config = 0;
-
- local_irq_enable();
-}
-
-static irqreturn_t imx_udc_irq(int irq, void *dev)
-{
- struct imx_udc_struct *imx_usb = dev;
- int intr = __raw_readl(imx_usb->base + USB_INTR);
- int temp;
-
- if (intr & (INTR_WAKEUP | INTR_SUSPEND | INTR_RESUME | INTR_RESET_START
- | INTR_RESET_STOP | INTR_CFG_CHG)) {
- dump_intr(__func__, intr, imx_usb->dev);
- dump_usb_stat(__func__, imx_usb);
- }
-
- if (!imx_usb->driver)
- goto end_irq;
-
- if (intr & INTR_SOF) {
- /* Copy from Freescale BSP.
- We must enable SOF intr and set CMDOVER.
- Datasheet don't specifiy this action, but it
- is done in Freescale BSP, so just copy it.
- */
- if (imx_usb->ep0state == EP0_IDLE) {
- temp = __raw_readl(imx_usb->base + USB_CTRL);
- __raw_writel(temp | CTRL_CMDOVER,
- imx_usb->base + USB_CTRL);
- }
- }
-
- if (intr & INTR_CFG_CHG) {
- /* A workaround of serious IMX UDC bug.
- Handling of CFG_CHG should be delayed for some time, because
- IMX does not NACK the host when CFG_CHG interrupt is pending.
- There is no time to handle current CFG_CHG
- if next CFG_CHG or SETUP packed is send immediately.
- We have to clear CFG_CHG, start the timer and
- NACK the host by setting CTRL_CMDOVER
- if it sends any SETUP packet.
- When timer expires, handler is called to handle configuration
- changes. While CFG_CHG is not handled (set_config=1),
- we must NACK the host to every SETUP packed.
- This delay prevents from going out of sync with host.
- */
- __raw_writel(INTR_CFG_CHG, imx_usb->base + USB_INTR);
- imx_usb->set_config = 1;
- mod_timer(&imx_usb->timer, jiffies + 5);
- goto end_irq;
- }
-
- if (intr & INTR_WAKEUP) {
- if (imx_usb->gadget.speed == USB_SPEED_UNKNOWN
- && imx_usb->driver && imx_usb->driver->resume)
- imx_usb->driver->resume(&imx_usb->gadget);
- imx_usb->set_config = 0;
- del_timer(&imx_usb->timer);
- imx_usb->gadget.speed = USB_SPEED_FULL;
- }
-
- if (intr & INTR_SUSPEND) {
- if (imx_usb->gadget.speed != USB_SPEED_UNKNOWN
- && imx_usb->driver && imx_usb->driver->suspend)
- imx_usb->driver->suspend(&imx_usb->gadget);
- imx_usb->set_config = 0;
- del_timer(&imx_usb->timer);
- imx_usb->gadget.speed = USB_SPEED_UNKNOWN;
- }
-
- if (intr & INTR_RESET_START) {
- __raw_writel(intr, imx_usb->base + USB_INTR);
- udc_stop_activity(imx_usb, imx_usb->driver);
- imx_usb->set_config = 0;
- del_timer(&imx_usb->timer);
- imx_usb->gadget.speed = USB_SPEED_UNKNOWN;
- }
-
- if (intr & INTR_RESET_STOP)
- imx_usb->gadget.speed = USB_SPEED_FULL;
-
-end_irq:
- __raw_writel(intr, imx_usb->base + USB_INTR);
- return IRQ_HANDLED;
-}
-
-static irqreturn_t imx_udc_ctrl_irq(int irq, void *dev)
-{
- struct imx_udc_struct *imx_usb = dev;
- struct imx_ep_struct *imx_ep = &imx_usb->imx_ep[0];
- int intr = __raw_readl(imx_usb->base + USB_EP_INTR(0));
-
- dump_ep_intr(__func__, 0, intr, imx_usb->dev);
-
- if (!imx_usb->driver) {
- __raw_writel(intr, imx_usb->base + USB_EP_INTR(0));
- return IRQ_HANDLED;
- }
-
- /* DEVREQ has highest priority */
- if (intr & (EPINTR_DEVREQ | EPINTR_MDEVREQ))
- handle_ep0_devreq(imx_usb);
- /* Seem i.MX is missing EOF interrupt sometimes.
- * Therefore we don't monitor EOF.
- * We call handle_ep0() only if a request is queued for ep0.
- */
- else if (!list_empty(&imx_ep->queue))
- handle_ep0(imx_ep);
-
- __raw_writel(intr, imx_usb->base + USB_EP_INTR(0));
-
- return IRQ_HANDLED;
-}
-
-#ifndef MX1_INT_USBD0
-#define MX1_INT_USBD0 MX1_USBD_INT0
-#endif
-
-static irqreturn_t imx_udc_bulk_irq(int irq, void *dev)
-{
- struct imx_udc_struct *imx_usb = dev;
- struct imx_ep_struct *imx_ep = &imx_usb->imx_ep[irq - MX1_INT_USBD0];
- int intr = __raw_readl(imx_usb->base + USB_EP_INTR(EP_NO(imx_ep)));
-
- dump_ep_intr(__func__, irq - MX1_INT_USBD0, intr, imx_usb->dev);
-
- if (!imx_usb->driver) {
- __raw_writel(intr, imx_usb->base + USB_EP_INTR(EP_NO(imx_ep)));
- return IRQ_HANDLED;
- }
-
- handle_ep(imx_ep);
-
- __raw_writel(intr, imx_usb->base + USB_EP_INTR(EP_NO(imx_ep)));
-
- return IRQ_HANDLED;
-}
-
-irq_handler_t intr_handler(int i)
-{
- switch (i) {
- case 0:
- return imx_udc_ctrl_irq;
- case 1:
- case 2:
- case 3:
- case 4:
- case 5:
- return imx_udc_bulk_irq;
- default:
- return imx_udc_irq;
- }
-}
-
-/*******************************************************************************
- * Static defined IMX UDC structure
- *******************************************************************************
- */
-
-static int imx_udc_start(struct usb_gadget *gadget,
- struct usb_gadget_driver *driver);
-static int imx_udc_stop(struct usb_gadget *gadget,
- struct usb_gadget_driver *driver);
-static const struct usb_gadget_ops imx_udc_ops = {
- .get_frame = imx_udc_get_frame,
- .wakeup = imx_udc_wakeup,
- .udc_start = imx_udc_start,
- .udc_stop = imx_udc_stop,
-};
-
-static struct imx_udc_struct controller = {
- .gadget = {
- .ops = &imx_udc_ops,
- .ep0 = &controller.imx_ep[0].ep,
- .name = driver_name,
- .dev = {
- .init_name = "gadget",
- },
- },
-
- .imx_ep[0] = {
- .ep = {
- .name = ep0name,
- .ops = &imx_ep_ops,
- .maxpacket = 32,
- },
- .imx_usb = &controller,
- .fifosize = 32,
- .bEndpointAddress = 0,
- .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
- },
- .imx_ep[1] = {
- .ep = {
- .name = "ep1in-bulk",
- .ops = &imx_ep_ops,
- .maxpacket = 64,
- },
- .imx_usb = &controller,
- .fifosize = 64,
- .bEndpointAddress = USB_DIR_IN | 1,
- .bmAttributes = USB_ENDPOINT_XFER_BULK,
- },
- .imx_ep[2] = {
- .ep = {
- .name = "ep2out-bulk",
- .ops = &imx_ep_ops,
- .maxpacket = 64,
- },
- .imx_usb = &controller,
- .fifosize = 64,
- .bEndpointAddress = USB_DIR_OUT | 2,
- .bmAttributes = USB_ENDPOINT_XFER_BULK,
- },
- .imx_ep[3] = {
- .ep = {
- .name = "ep3out-bulk",
- .ops = &imx_ep_ops,
- .maxpacket = 32,
- },
- .imx_usb = &controller,
- .fifosize = 32,
- .bEndpointAddress = USB_DIR_OUT | 3,
- .bmAttributes = USB_ENDPOINT_XFER_BULK,
- },
- .imx_ep[4] = {
- .ep = {
- .name = "ep4in-int",
- .ops = &imx_ep_ops,
- .maxpacket = 32,
- },
- .imx_usb = &controller,
- .fifosize = 32,
- .bEndpointAddress = USB_DIR_IN | 4,
- .bmAttributes = USB_ENDPOINT_XFER_INT,
- },
- .imx_ep[5] = {
- .ep = {
- .name = "ep5out-int",
- .ops = &imx_ep_ops,
- .maxpacket = 32,
- },
- .imx_usb = &controller,
- .fifosize = 32,
- .bEndpointAddress = USB_DIR_OUT | 5,
- .bmAttributes = USB_ENDPOINT_XFER_INT,
- },
-};
-
-/*******************************************************************************
- * USB gadget driver functions
- *******************************************************************************
- */
-static int imx_udc_start(struct usb_gadget *gadget,
- struct usb_gadget_driver *driver)
-{
- struct imx_udc_struct *imx_usb;
-
- imx_usb = container_of(gadget, struct imx_udc_struct, gadget);
- /* first hook up the driver ... */
- imx_usb->driver = driver;
-
- D_INI(imx_usb->dev, "<%s> registered gadget driver '%s'\n",
- __func__, driver->driver.name);
-
- imx_udc_enable(imx_usb);
-
- return 0;
-}
-
-static int imx_udc_stop(struct usb_gadget *gadget,
- struct usb_gadget_driver *driver)
-{
- struct imx_udc_struct *imx_usb = container_of(gadget,
- struct imx_udc_struct, gadget);
-
- udc_stop_activity(imx_usb, driver);
- imx_udc_disable(imx_usb);
- del_timer(&imx_usb->timer);
-
- imx_usb->driver = NULL;
-
- D_INI(imx_usb->dev, "<%s> unregistered gadget driver '%s'\n",
- __func__, driver->driver.name);
-
- return 0;
-}
-
-/*******************************************************************************
- * Module functions
- *******************************************************************************
- */
-
-static int __init imx_udc_probe(struct platform_device *pdev)
-{
- struct imx_udc_struct *imx_usb = &controller;
- struct resource *res;
- struct imxusb_platform_data *pdata;
- struct clk *clk;
- void __iomem *base;
- int ret = 0;
- int i;
- resource_size_t res_size;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "can't get device resources\n");
- return -ENODEV;
- }
-
- pdata = pdev->dev.platform_data;
- if (!pdata) {
- dev_err(&pdev->dev, "driver needs platform data\n");
- return -ENODEV;
- }
-
- res_size = resource_size(res);
- if (!request_mem_region(res->start, res_size, res->name)) {
- dev_err(&pdev->dev, "can't allocate %d bytes at %d address\n",
- res_size, res->start);
- return -ENOMEM;
- }
-
- if (pdata->init) {
- ret = pdata->init(&pdev->dev);
- if (ret)
- goto fail0;
- }
-
- base = ioremap(res->start, res_size);
- if (!base) {
- dev_err(&pdev->dev, "ioremap failed\n");
- ret = -EIO;
- goto fail1;
- }
-
- clk = clk_get(NULL, "usbd_clk");
- if (IS_ERR(clk)) {
- ret = PTR_ERR(clk);
- dev_err(&pdev->dev, "can't get USB clock\n");
- goto fail2;
- }
- clk_prepare_enable(clk);
-
- if (clk_get_rate(clk) != 48000000) {
- D_INI(&pdev->dev,
- "Bad USB clock (%d Hz), changing to 48000000 Hz\n",
- (int)clk_get_rate(clk));
- if (clk_set_rate(clk, 48000000)) {
- dev_err(&pdev->dev,
- "Unable to set correct USB clock (48MHz)\n");
- ret = -EIO;
- goto fail3;
- }
- }
-
- for (i = 0; i < IMX_USB_NB_EP + 1; i++) {
- imx_usb->usbd_int[i] = platform_get_irq(pdev, i);
- if (imx_usb->usbd_int[i] < 0) {
- dev_err(&pdev->dev, "can't get irq number\n");
- ret = -ENODEV;
- goto fail3;
- }
- }
-
- for (i = 0; i < IMX_USB_NB_EP + 1; i++) {
- ret = request_irq(imx_usb->usbd_int[i], intr_handler(i),
- 0, driver_name, imx_usb);
- if (ret) {
- dev_err(&pdev->dev, "can't get irq %i, err %d\n",
- imx_usb->usbd_int[i], ret);
- for (--i; i >= 0; i--)
- free_irq(imx_usb->usbd_int[i], imx_usb);
- goto fail3;
- }
- }
-
- imx_usb->res = res;
- imx_usb->base = base;
- imx_usb->clk = clk;
- imx_usb->dev = &pdev->dev;
-
- platform_set_drvdata(pdev, imx_usb);
-
- usb_init_data(imx_usb);
- imx_udc_init(imx_usb);
-
- init_timer(&imx_usb->timer);
- imx_usb->timer.function = handle_config;
- imx_usb->timer.data = (unsigned long)imx_usb;
-
- ret = usb_add_gadget_udc(&pdev->dev, &imx_usb->gadget);
- if (ret)
- goto fail4;
-
- return 0;
-fail4:
- for (i = 0; i < IMX_USB_NB_EP + 1; i++)
- free_irq(imx_usb->usbd_int[i], imx_usb);
-fail3:
- clk_put(clk);
- clk_disable_unprepare(clk);
-fail2:
- iounmap(base);
-fail1:
- if (pdata->exit)
- pdata->exit(&pdev->dev);
-fail0:
- release_mem_region(res->start, res_size);
- return ret;
-}
-
-static int __exit imx_udc_remove(struct platform_device *pdev)
-{
- struct imx_udc_struct *imx_usb = platform_get_drvdata(pdev);
- struct imxusb_platform_data *pdata = pdev->dev.platform_data;
- int i;
-
- usb_del_gadget_udc(&imx_usb->gadget);
- imx_udc_disable(imx_usb);
- del_timer(&imx_usb->timer);
-
- for (i = 0; i < IMX_USB_NB_EP + 1; i++)
- free_irq(imx_usb->usbd_int[i], imx_usb);
-
- clk_put(imx_usb->clk);
- clk_disable_unprepare(imx_usb->clk);
- iounmap(imx_usb->base);
-
- release_mem_region(imx_usb->res->start, resource_size(imx_usb->res));
-
- if (pdata->exit)
- pdata->exit(&pdev->dev);
-
- return 0;
-}
-
-/*----------------------------------------------------------------------------*/
-
-#ifdef CONFIG_PM
-#define imx_udc_suspend NULL
-#define imx_udc_resume NULL
-#else
-#define imx_udc_suspend NULL
-#define imx_udc_resume NULL
-#endif
-
-/*----------------------------------------------------------------------------*/
-
-static struct platform_driver udc_driver = {
- .driver = {
- .name = driver_name,
- .owner = THIS_MODULE,
- },
- .remove = __exit_p(imx_udc_remove),
- .suspend = imx_udc_suspend,
- .resume = imx_udc_resume,
-};
-
-module_platform_driver_probe(udc_driver, imx_udc_probe);
-
-MODULE_DESCRIPTION("IMX USB Device Controller driver");
-MODULE_AUTHOR("Darius Augulis <augulis.darius@gmail.com>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:imx_udc");
diff --git a/drivers/usb/gadget/imx_udc.h b/drivers/usb/gadget/imx_udc.h
deleted file mode 100644
index d118fb7..0000000
--- a/drivers/usb/gadget/imx_udc.h
+++ /dev/null
@@ -1,351 +0,0 @@
-/*
- * Copyright (C) 2005 Mike Lee(eemike@gmail.com)
- *
- * This udc driver is now under testing and code is based on pxa2xx_udc.h
- * Please use it with your own risk!
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef __LINUX_USB_GADGET_IMX_H
-#define __LINUX_USB_GADGET_IMX_H
-
-#include <linux/types.h>
-
-/* Helper macros */
-#define EP_NO(ep) ((ep->bEndpointAddress) & ~USB_DIR_IN) /* IN:1, OUT:0 */
-#define EP_DIR(ep) ((ep->bEndpointAddress) & USB_DIR_IN ? 1 : 0)
-#define IMX_USB_NB_EP 6
-
-/* Driver structures */
-struct imx_request {
- struct usb_request req;
- struct list_head queue;
- unsigned int in_use;
-};
-
-enum ep0_state {
- EP0_IDLE,
- EP0_IN_DATA_PHASE,
- EP0_OUT_DATA_PHASE,
- EP0_CONFIG,
- EP0_STALL,
-};
-
-struct imx_ep_struct {
- struct usb_ep ep;
- struct imx_udc_struct *imx_usb;
- struct list_head queue;
- unsigned char stopped;
- unsigned char fifosize;
- unsigned char bEndpointAddress;
- unsigned char bmAttributes;
-};
-
-struct imx_udc_struct {
- struct usb_gadget gadget;
- struct usb_gadget_driver *driver;
- struct device *dev;
- struct imx_ep_struct imx_ep[IMX_USB_NB_EP];
- struct clk *clk;
- struct timer_list timer;
- enum ep0_state ep0state;
- struct resource *res;
- void __iomem *base;
- unsigned char set_config;
- int cfg,
- intf,
- alt,
- usbd_int[7];
-};
-
-/* USB registers */
-#define USB_FRAME (0x00) /* USB frame */
-#define USB_SPEC (0x04) /* USB Spec */
-#define USB_STAT (0x08) /* USB Status */
-#define USB_CTRL (0x0C) /* USB Control */
-#define USB_DADR (0x10) /* USB Desc RAM addr */
-#define USB_DDAT (0x14) /* USB Desc RAM/EP buffer data */
-#define USB_INTR (0x18) /* USB interrupt */
-#define USB_MASK (0x1C) /* USB Mask */
-#define USB_ENAB (0x24) /* USB Enable */
-#define USB_EP_STAT(x) (0x30 + (x*0x30)) /* USB status/control */
-#define USB_EP_INTR(x) (0x34 + (x*0x30)) /* USB interrupt */
-#define USB_EP_MASK(x) (0x38 + (x*0x30)) /* USB mask */
-#define USB_EP_FDAT(x) (0x3C + (x*0x30)) /* USB FIFO data */
-#define USB_EP_FDAT0(x) (0x3C + (x*0x30)) /* USB FIFO data */
-#define USB_EP_FDAT1(x) (0x3D + (x*0x30)) /* USB FIFO data */
-#define USB_EP_FDAT2(x) (0x3E + (x*0x30)) /* USB FIFO data */
-#define USB_EP_FDAT3(x) (0x3F + (x*0x30)) /* USB FIFO data */
-#define USB_EP_FSTAT(x) (0x40 + (x*0x30)) /* USB FIFO status */
-#define USB_EP_FCTRL(x) (0x44 + (x*0x30)) /* USB FIFO control */
-#define USB_EP_LRFP(x) (0x48 + (x*0x30)) /* USB last rd f. pointer */
-#define USB_EP_LWFP(x) (0x4C + (x*0x30)) /* USB last wr f. pointer */
-#define USB_EP_FALRM(x) (0x50 + (x*0x30)) /* USB FIFO alarm */
-#define USB_EP_FRDP(x) (0x54 + (x*0x30)) /* USB FIFO read pointer */
-#define USB_EP_FWRP(x) (0x58 + (x*0x30)) /* USB FIFO write pointer */
-/* USB Control Register Bit Fields.*/
-#define CTRL_CMDOVER (1<<6) /* UDC status */
-#define CTRL_CMDERROR (1<<5) /* UDC status */
-#define CTRL_FE_ENA (1<<3) /* Enable Font End logic */
-#define CTRL_UDC_RST (1<<2) /* UDC reset */
-#define CTRL_AFE_ENA (1<<1) /* Analog Font end enable */
-#define CTRL_RESUME (1<<0) /* UDC resume */
-/* USB Status Register Bit Fields.*/
-#define STAT_RST (1<<8)
-#define STAT_SUSP (1<<7)
-#define STAT_CFG (3<<5)
-#define STAT_INTF (3<<3)
-#define STAT_ALTSET (7<<0)
-/* USB Interrupt Status/Mask Registers Bit fields */
-#define INTR_WAKEUP (1<<31) /* Wake up Interrupt */
-#define INTR_MSOF (1<<7) /* Missed Start of Frame */
-#define INTR_SOF (1<<6) /* Start of Frame */
-#define INTR_RESET_STOP (1<<5) /* Reset Signaling stop */
-#define INTR_RESET_START (1<<4) /* Reset Signaling start */
-#define INTR_RESUME (1<<3) /* Suspend to resume */
-#define INTR_SUSPEND (1<<2) /* Active to suspend */
-#define INTR_FRAME_MATCH (1<<1) /* Frame matched */
-#define INTR_CFG_CHG (1<<0) /* Configuration change occurred */
-/* USB Enable Register Bit Fields.*/
-#define ENAB_RST (1<<31) /* Reset USB modules */
-#define ENAB_ENAB (1<<30) /* Enable USB modules*/
-#define ENAB_SUSPEND (1<<29) /* Suspend USB modules */
-#define ENAB_ENDIAN (1<<28) /* Endian of USB modules */
-#define ENAB_PWRMD (1<<0) /* Power mode of USB modules */
-/* USB Descriptor Ram Address Register bit fields */
-#define DADR_CFG (1<<31) /* Configuration */
-#define DADR_BSY (1<<30) /* Busy status */
-#define DADR_DADR (0x1FF) /* Descriptor Ram Address */
-/* USB Descriptor RAM/Endpoint Buffer Data Register bit fields */
-#define DDAT_DDAT (0xFF) /* Descriptor Endpoint Buffer */
-/* USB Endpoint Status Register bit fields */
-#define EPSTAT_BCOUNT (0x7F<<16) /* Endpoint FIFO byte count */
-#define EPSTAT_SIP (1<<8) /* Endpoint setup in progress */
-#define EPSTAT_DIR (1<<7) /* Endpoint transfer direction */
-#define EPSTAT_MAX (3<<5) /* Endpoint Max packet size */
-#define EPSTAT_TYP (3<<3) /* Endpoint type */
-#define EPSTAT_ZLPS (1<<2) /* Send zero length packet */
-#define EPSTAT_FLUSH (1<<1) /* Endpoint FIFO Flush */
-#define EPSTAT_STALL (1<<0) /* Force stall */
-/* USB Endpoint FIFO Status Register bit fields */
-#define FSTAT_FRAME_STAT (0xF<<24) /* Frame status bit [0-3] */
-#define FSTAT_ERR (1<<22) /* FIFO error */
-#define FSTAT_UF (1<<21) /* FIFO underflow */
-#define FSTAT_OF (1<<20) /* FIFO overflow */
-#define FSTAT_FR (1<<19) /* FIFO frame ready */
-#define FSTAT_FULL (1<<18) /* FIFO full */
-#define FSTAT_ALRM (1<<17) /* FIFO alarm */
-#define FSTAT_EMPTY (1<<16) /* FIFO empty */
-/* USB Endpoint FIFO Control Register bit fields */
-#define FCTRL_WFR (1<<29) /* Write frame end */
-/* USB Endpoint Interrupt Status Regsiter bit fields */
-#define EPINTR_FIFO_FULL (1<<8) /* fifo full */
-#define EPINTR_FIFO_EMPTY (1<<7) /* fifo empty */
-#define EPINTR_FIFO_ERROR (1<<6) /* fifo error */
-#define EPINTR_FIFO_HIGH (1<<5) /* fifo high */
-#define EPINTR_FIFO_LOW (1<<4) /* fifo low */
-#define EPINTR_MDEVREQ (1<<3) /* multi Device request */
-#define EPINTR_EOT (1<<2) /* fifo end of transfer */
-#define EPINTR_DEVREQ (1<<1) /* Device request */
-#define EPINTR_EOF (1<<0) /* fifo end of frame */
-
-/* Debug macros */
-#ifdef DEBUG
-
-/* #define DEBUG_REQ */
-/* #define DEBUG_TRX */
-/* #define DEBUG_INIT */
-/* #define DEBUG_EP0 */
-/* #define DEBUG_EPX */
-/* #define DEBUG_IRQ */
-/* #define DEBUG_EPIRQ */
-/* #define DEBUG_DUMP */
-/* #define DEBUG_ERR */
-
-#ifdef DEBUG_REQ
- #define D_REQ(dev, args...) dev_dbg(dev, ## args)
-#else
- #define D_REQ(dev, args...) do {} while (0)
-#endif /* DEBUG_REQ */
-
-#ifdef DEBUG_TRX
- #define D_TRX(dev, args...) dev_dbg(dev, ## args)
-#else
- #define D_TRX(dev, args...) do {} while (0)
-#endif /* DEBUG_TRX */
-
-#ifdef DEBUG_INIT
- #define D_INI(dev, args...) dev_dbg(dev, ## args)
-#else
- #define D_INI(dev, args...) do {} while (0)
-#endif /* DEBUG_INIT */
-
-#ifdef DEBUG_EP0
- static const char *state_name[] = {
- "EP0_IDLE",
- "EP0_IN_DATA_PHASE",
- "EP0_OUT_DATA_PHASE",
- "EP0_CONFIG",
- "EP0_STALL"
- };
- #define D_EP0(dev, args...) dev_dbg(dev, ## args)
-#else
- #define D_EP0(dev, args...) do {} while (0)
-#endif /* DEBUG_EP0 */
-
-#ifdef DEBUG_EPX
- #define D_EPX(dev, args...) dev_dbg(dev, ## args)
-#else
- #define D_EPX(dev, args...) do {} while (0)
-#endif /* DEBUG_EP0 */
-
-#ifdef DEBUG_IRQ
- static void dump_intr(const char *label, int irqreg, struct device *dev)
- {
- dev_dbg(dev, "<%s> USB_INTR=[%s%s%s%s%s%s%s%s%s]\n", label,
- (irqreg & INTR_WAKEUP) ? " wake" : "",
- (irqreg & INTR_MSOF) ? " msof" : "",
- (irqreg & INTR_SOF) ? " sof" : "",
- (irqreg & INTR_RESUME) ? " resume" : "",
- (irqreg & INTR_SUSPEND) ? " suspend" : "",
- (irqreg & INTR_RESET_STOP) ? " noreset" : "",
- (irqreg & INTR_RESET_START) ? " reset" : "",
- (irqreg & INTR_FRAME_MATCH) ? " fmatch" : "",
- (irqreg & INTR_CFG_CHG) ? " config" : "");
- }
-#else
- #define dump_intr(x, y, z) do {} while (0)
-#endif /* DEBUG_IRQ */
-
-#ifdef DEBUG_EPIRQ
- static void dump_ep_intr(const char *label, int nr, int irqreg,
- struct device *dev)
- {
- dev_dbg(dev, "<%s> EP%d_INTR=[%s%s%s%s%s%s%s%s%s]\n", label, nr,
- (irqreg & EPINTR_FIFO_FULL) ? " full" : "",
- (irqreg & EPINTR_FIFO_EMPTY) ? " fempty" : "",
- (irqreg & EPINTR_FIFO_ERROR) ? " ferr" : "",
- (irqreg & EPINTR_FIFO_HIGH) ? " fhigh" : "",
- (irqreg & EPINTR_FIFO_LOW) ? " flow" : "",
- (irqreg & EPINTR_MDEVREQ) ? " mreq" : "",
- (irqreg & EPINTR_EOF) ? " eof" : "",
- (irqreg & EPINTR_DEVREQ) ? " devreq" : "",
- (irqreg & EPINTR_EOT) ? " eot" : "");
- }
-#else
- #define dump_ep_intr(x, y, z, i) do {} while (0)
-#endif /* DEBUG_IRQ */
-
-#ifdef DEBUG_DUMP
- static void dump_usb_stat(const char *label,
- struct imx_udc_struct *imx_usb)
- {
- int temp = __raw_readl(imx_usb->base + USB_STAT);
-
- dev_dbg(imx_usb->dev,
- "<%s> USB_STAT=[%s%s CFG=%d, INTF=%d, ALTR=%d]\n", label,
- (temp & STAT_RST) ? " reset" : "",
- (temp & STAT_SUSP) ? " suspend" : "",
- (temp & STAT_CFG) >> 5,
- (temp & STAT_INTF) >> 3,
- (temp & STAT_ALTSET));
- }
-
- static void dump_ep_stat(const char *label,
- struct imx_ep_struct *imx_ep)
- {
- int temp = __raw_readl(imx_ep->imx_usb->base
- + USB_EP_INTR(EP_NO(imx_ep)));
-
- dev_dbg(imx_ep->imx_usb->dev,
- "<%s> EP%d_INTR=[%s%s%s%s%s%s%s%s%s]\n",
- label, EP_NO(imx_ep),
- (temp & EPINTR_FIFO_FULL) ? " full" : "",
- (temp & EPINTR_FIFO_EMPTY) ? " fempty" : "",
- (temp & EPINTR_FIFO_ERROR) ? " ferr" : "",
- (temp & EPINTR_FIFO_HIGH) ? " fhigh" : "",
- (temp & EPINTR_FIFO_LOW) ? " flow" : "",
- (temp & EPINTR_MDEVREQ) ? " mreq" : "",
- (temp & EPINTR_EOF) ? " eof" : "",
- (temp & EPINTR_DEVREQ) ? " devreq" : "",
- (temp & EPINTR_EOT) ? " eot" : "");
-
- temp = __raw_readl(imx_ep->imx_usb->base
- + USB_EP_STAT(EP_NO(imx_ep)));
-
- dev_dbg(imx_ep->imx_usb->dev,
- "<%s> EP%d_STAT=[%s%s bcount=%d]\n",
- label, EP_NO(imx_ep),
- (temp & EPSTAT_SIP) ? " sip" : "",
- (temp & EPSTAT_STALL) ? " stall" : "",
- (temp & EPSTAT_BCOUNT) >> 16);
-
- temp = __raw_readl(imx_ep->imx_usb->base
- + USB_EP_FSTAT(EP_NO(imx_ep)));
-
- dev_dbg(imx_ep->imx_usb->dev,
- "<%s> EP%d_FSTAT=[%s%s%s%s%s%s%s]\n",
- label, EP_NO(imx_ep),
- (temp & FSTAT_ERR) ? " ferr" : "",
- (temp & FSTAT_UF) ? " funder" : "",
- (temp & FSTAT_OF) ? " fover" : "",
- (temp & FSTAT_FR) ? " fready" : "",
- (temp & FSTAT_FULL) ? " ffull" : "",
- (temp & FSTAT_ALRM) ? " falarm" : "",
- (temp & FSTAT_EMPTY) ? " fempty" : "");
- }
-
- static void dump_req(const char *label, struct imx_ep_struct *imx_ep,
- struct usb_request *req)
- {
- int i;
-
- if (!req || !req->buf) {
- dev_dbg(imx_ep->imx_usb->dev,
- "<%s> req or req buf is free\n", label);
- return;
- }
-
- if ((!EP_NO(imx_ep) && imx_ep->imx_usb->ep0state
- == EP0_IN_DATA_PHASE)
- || (EP_NO(imx_ep) && EP_DIR(imx_ep))) {
-
- dev_dbg(imx_ep->imx_usb->dev,
- "<%s> request dump <", label);
- for (i = 0; i < req->length; i++)
- printk("%02x-", *((u8 *)req->buf + i));
- printk(">\n");
- }
- }
-
-#else
- #define dump_ep_stat(x, y) do {} while (0)
- #define dump_usb_stat(x, y) do {} while (0)
- #define dump_req(x, y, z) do {} while (0)
-#endif /* DEBUG_DUMP */
-
-#ifdef DEBUG_ERR
- #define D_ERR(dev, args...) dev_dbg(dev, ## args)
-#else
- #define D_ERR(dev, args...) do {} while (0)
-#endif
-
-#else
- #define D_REQ(dev, args...) do {} while (0)
- #define D_TRX(dev, args...) do {} while (0)
- #define D_INI(dev, args...) do {} while (0)
- #define D_EP0(dev, args...) do {} while (0)
- #define D_EPX(dev, args...) do {} while (0)
- #define dump_ep_intr(x, y, z, i) do {} while (0)
- #define dump_intr(x, y, z) do {} while (0)
- #define dump_ep_stat(x, y) do {} while (0)
- #define dump_usb_stat(x, y) do {} while (0)
- #define dump_req(x, y, z) do {} while (0)
- #define D_ERR(dev, args...) do {} while (0)
-#endif /* DEBUG */
-
-#endif /* __LINUX_USB_GADGET_IMX_H */
diff --git a/drivers/usb/gadget/m66592-udc.c b/drivers/usb/gadget/m66592-udc.c
index 46ba983..d5f050d 100644
--- a/drivers/usb/gadget/m66592-udc.c
+++ b/drivers/usb/gadget/m66592-udc.c
@@ -1584,7 +1584,7 @@
goto clean_up;
}
- if (pdev->dev.platform_data == NULL) {
+ if (dev_get_platdata(&pdev->dev) == NULL) {
dev_err(&pdev->dev, "no platform data\n");
ret = -ENODEV;
goto clean_up;
@@ -1598,7 +1598,7 @@
goto clean_up;
}
- m66592->pdata = pdev->dev.platform_data;
+ m66592->pdata = dev_get_platdata(&pdev->dev);
m66592->irq_trigger = ires->flags & IRQF_TRIGGER_MASK;
spin_lock_init(&m66592->lock);
diff --git a/drivers/usb/gadget/mv_u3d_core.c b/drivers/usb/gadget/mv_u3d_core.c
index ec6a2d2..bbb6e98 100644
--- a/drivers/usb/gadget/mv_u3d_core.c
+++ b/drivers/usb/gadget/mv_u3d_core.c
@@ -1109,7 +1109,7 @@
static int mv_u3d_enable(struct mv_u3d *u3d)
{
- struct mv_usb_platform_data *pdata = u3d->dev->platform_data;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
int retval;
if (u3d->active)
@@ -1138,7 +1138,7 @@
static void mv_u3d_disable(struct mv_u3d *u3d)
{
- struct mv_usb_platform_data *pdata = u3d->dev->platform_data;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
if (u3d->clock_gating && u3d->active) {
dev_dbg(u3d->dev, "disable u3d\n");
if (pdata->phy_deinit)
@@ -1246,7 +1246,7 @@
struct usb_gadget_driver *driver)
{
struct mv_u3d *u3d = container_of(g, struct mv_u3d, gadget);
- struct mv_usb_platform_data *pdata = u3d->dev->platform_data;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
unsigned long flags;
if (u3d->driver)
@@ -1277,7 +1277,7 @@
struct usb_gadget_driver *driver)
{
struct mv_u3d *u3d = container_of(g, struct mv_u3d, gadget);
- struct mv_usb_platform_data *pdata = u3d->dev->platform_data;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
unsigned long flags;
u3d->vbus_valid_detect = 0;
@@ -1794,12 +1794,12 @@
static int mv_u3d_probe(struct platform_device *dev)
{
struct mv_u3d *u3d = NULL;
- struct mv_usb_platform_data *pdata = dev->dev.platform_data;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(&dev->dev);
int retval = 0;
struct resource *r;
size_t size;
- if (!dev->dev.platform_data) {
+ if (!dev_get_platdata(&dev->dev)) {
dev_err(&dev->dev, "missing platform_data\n");
retval = -ENODEV;
goto err_pdata;
diff --git a/drivers/usb/gadget/mv_udc_core.c b/drivers/usb/gadget/mv_udc_core.c
index c2a5702..104cdbe 100644
--- a/drivers/usb/gadget/mv_udc_core.c
+++ b/drivers/usb/gadget/mv_udc_core.c
@@ -2100,7 +2100,7 @@
static int mv_udc_probe(struct platform_device *pdev)
{
- struct mv_usb_platform_data *pdata = pdev->dev.platform_data;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct mv_udc *udc;
int retval = 0;
struct resource *r;
@@ -2118,7 +2118,7 @@
}
udc->done = &release_done;
- udc->pdata = pdev->dev.platform_data;
+ udc->pdata = dev_get_platdata(&pdev->dev);
spin_lock_init(&udc->lock);
udc->dev = pdev;
diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c
index b8ed74a..83957cc 100644
--- a/drivers/usb/gadget/omap_udc.c
+++ b/drivers/usb/gadget/omap_udc.c
@@ -2734,7 +2734,7 @@
int hmc;
struct usb_phy *xceiv = NULL;
const char *type = NULL;
- struct omap_usb_config *config = pdev->dev.platform_data;
+ struct omap_usb_config *config = dev_get_platdata(&pdev->dev);
struct clk *dc_clk = NULL;
struct clk *hhc_clk = NULL;
diff --git a/drivers/usb/gadget/pxa25x_udc.c b/drivers/usb/gadget/pxa25x_udc.c
index 95c531d..cc92074 100644
--- a/drivers/usb/gadget/pxa25x_udc.c
+++ b/drivers/usb/gadget/pxa25x_udc.c
@@ -2117,7 +2117,7 @@
/* other non-static parts of init */
dev->dev = &pdev->dev;
- dev->mach = pdev->dev.platform_data;
+ dev->mach = dev_get_platdata(&pdev->dev);
dev->transceiver = usb_get_phy(USB_PHY_TYPE_USB2);
diff --git a/drivers/usb/gadget/pxa27x_udc.c b/drivers/usb/gadget/pxa27x_udc.c
index 41cea95..3c97da7 100644
--- a/drivers/usb/gadget/pxa27x_udc.c
+++ b/drivers/usb/gadget/pxa27x_udc.c
@@ -2422,7 +2422,7 @@
return udc->irq;
udc->dev = &pdev->dev;
- udc->mach = pdev->dev.platform_data;
+ udc->mach = dev_get_platdata(&pdev->dev);
udc->transceiver = usb_get_phy(USB_PHY_TYPE_USB2);
gpio = udc->mach->gpio_pullup;
diff --git a/drivers/usb/gadget/r8a66597-udc.c b/drivers/usb/gadget/r8a66597-udc.c
index c6af649..68be48d 100644
--- a/drivers/usb/gadget/r8a66597-udc.c
+++ b/drivers/usb/gadget/r8a66597-udc.c
@@ -1910,7 +1910,7 @@
spin_lock_init(&r8a66597->lock);
platform_set_drvdata(pdev, r8a66597);
- r8a66597->pdata = pdev->dev.platform_data;
+ r8a66597->pdata = dev_get_platdata(&pdev->dev);
r8a66597->irq_sense_low = irq_trigger == IRQF_TRIGGER_LOW;
r8a66597->gadget.ops = &r8a66597_gadget_ops;
diff --git a/drivers/usb/gadget/rndis.c b/drivers/usb/gadget/rndis.c
index 3e3ea72..9575085 100644
--- a/drivers/usb/gadget/rndis.c
+++ b/drivers/usb/gadget/rndis.c
@@ -1142,7 +1142,7 @@
#endif /* CONFIG_USB_GADGET_DEBUG_FILES */
-int rndis_init(void)
+static int rndis_init(void)
{
u8 i;
@@ -1176,7 +1176,7 @@
}
module_init(rndis_init);
-void rndis_exit(void)
+static void rndis_exit(void)
{
#ifdef CONFIG_USB_GADGET_DEBUG_FILES
u8 i;
diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index af22f24..d69b36a 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -29,6 +29,7 @@
#include <linux/slab.h>
#include <linux/clk.h>
#include <linux/regulator/consumer.h>
+#include <linux/of_platform.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
@@ -3450,7 +3451,7 @@
static int s3c_hsotg_probe(struct platform_device *pdev)
{
- struct s3c_hsotg_plat *plat = pdev->dev.platform_data;
+ struct s3c_hsotg_plat *plat = dev_get_platdata(&pdev->dev);
struct usb_phy *phy;
struct device *dev = &pdev->dev;
struct s3c_hsotg_ep *eps;
@@ -3469,7 +3470,7 @@
phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
if (IS_ERR(phy)) {
/* Fallback for pdata */
- plat = pdev->dev.platform_data;
+ plat = dev_get_platdata(&pdev->dev);
if (!plat) {
dev_err(&pdev->dev, "no platform data or transceiver defined\n");
return -EPROBE_DEFER;
@@ -3648,10 +3649,19 @@
#define s3c_hsotg_resume NULL
#endif
+#ifdef CONFIG_OF
+static const struct of_device_id s3c_hsotg_of_ids[] = {
+ { .compatible = "samsung,s3c6400-hsotg", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, s3c_hsotg_of_ids);
+#endif
+
static struct platform_driver s3c_hsotg_driver = {
.driver = {
.name = "s3c-hsotg",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(s3c_hsotg_of_ids),
},
.probe = s3c_hsotg_probe,
.remove = s3c_hsotg_remove,
diff --git a/drivers/usb/gadget/s3c-hsudc.c b/drivers/usb/gadget/s3c-hsudc.c
index b1f0771..1a1a414 100644
--- a/drivers/usb/gadget/s3c-hsudc.c
+++ b/drivers/usb/gadget/s3c-hsudc.c
@@ -1262,7 +1262,7 @@
struct device *dev = &pdev->dev;
struct resource *res;
struct s3c_hsudc *hsudc;
- struct s3c24xx_hsudc_platdata *pd = pdev->dev.platform_data;
+ struct s3c24xx_hsudc_platdata *pd = dev_get_platdata(&pdev->dev);
int ret, i;
hsudc = devm_kzalloc(&pdev->dev, sizeof(struct s3c_hsudc) +
@@ -1275,7 +1275,7 @@
platform_set_drvdata(pdev, dev);
hsudc->dev = dev;
- hsudc->pd = pdev->dev.platform_data;
+ hsudc->pd = dev_get_platdata(&pdev->dev);
hsudc->transceiver = usb_get_phy(USB_PHY_TYPE_USB2);
diff --git a/drivers/usb/gadget/s3c2410_udc.c b/drivers/usb/gadget/s3c2410_udc.c
index 09c4f70..c72d810 100644
--- a/drivers/usb/gadget/s3c2410_udc.c
+++ b/drivers/usb/gadget/s3c2410_udc.c
@@ -1809,7 +1809,7 @@
}
spin_lock_init(&udc->lock);
- udc_info = pdev->dev.platform_data;
+ udc_info = dev_get_platdata(&pdev->dev);
rsrc_start = S3C2410_PA_USBDEV;
rsrc_len = S3C24XX_SZ_USBDEV;
diff --git a/drivers/usb/gadget/u_uac1.c b/drivers/usb/gadget/u_uac1.c
index c7d460f..7a55fea 100644
--- a/drivers/usb/gadget/u_uac1.c
+++ b/drivers/usb/gadget/u_uac1.c
@@ -191,7 +191,7 @@
frames = bytes_to_frames(runtime, count);
old_fs = get_fs();
set_fs(KERNEL_DS);
- result = snd_pcm_lib_write(snd->substream, buf, frames);
+ result = snd_pcm_lib_write(snd->substream, (void __user *)buf, frames);
if (result != frames) {
ERROR(card, "Playback error: %d\n", (int)result);
set_fs(old_fs);
diff --git a/drivers/usb/gadget/udc-core.c b/drivers/usb/gadget/udc-core.c
index c28ac98..3122ab9 100644
--- a/drivers/usb/gadget/udc-core.c
+++ b/drivers/usb/gadget/udc-core.c
@@ -23,6 +23,7 @@
#include <linux/list.h>
#include <linux/err.h>
#include <linux/dma-mapping.h>
+#include <linux/workqueue.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
@@ -105,11 +106,18 @@
/* ------------------------------------------------------------------------- */
+static void usb_gadget_state_work(struct work_struct *work)
+{
+ struct usb_gadget *gadget = work_to_gadget(work);
+
+ sysfs_notify(&gadget->dev.kobj, NULL, "status");
+}
+
void usb_gadget_set_state(struct usb_gadget *gadget,
enum usb_device_state state)
{
gadget->state = state;
- sysfs_notify(&gadget->dev.kobj, NULL, "status");
+ schedule_work(&gadget->work);
}
EXPORT_SYMBOL_GPL(usb_gadget_set_state);
@@ -196,6 +204,7 @@
goto err1;
dev_set_name(&gadget->dev, "gadget");
+ INIT_WORK(&gadget->work, usb_gadget_state_work);
gadget->dev.parent = parent;
#ifdef CONFIG_HAS_DMA
@@ -315,6 +324,7 @@
usb_gadget_remove_driver(udc);
kobject_uevent(&udc->dev.kobj, KOBJ_REMOVE);
+ flush_work(&gadget->work);
device_unregister(&udc->dev);
device_unregister(&gadget->dev);
}
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 4263d01..5064e06 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -148,13 +148,11 @@
config USB_EHCI_HCD_OMAP
tristate "EHCI support for OMAP3 and later chips"
depends on ARCH_OMAP
+ select NOP_USB_XCEIV
default y
---help---
Enables support for the on-chip EHCI controller on
OMAP3 and later chips.
- If your system uses a PHY on the USB port, you will need to
- enable USB_PHY and the appropriate PHY driver as well. Most
- boards need the NOP_USB_XCEIV PHY driver.
config USB_EHCI_HCD_ORION
tristate "Support for Marvell EBU on-chip EHCI USB controller"
@@ -186,7 +184,6 @@
config USB_EHCI_MSM
tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller"
depends on ARCH_MSM
- depends on USB_PHY
select USB_EHCI_ROOT_HUB_TT
select USB_MSM_OTG
---help---
diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c
index 6ee7ef7..db8031f 100644
--- a/drivers/usb/host/ehci-tegra.c
+++ b/drivers/usb/host/ehci-tegra.c
@@ -27,7 +27,6 @@
#include <linux/of.h>
#include <linux/of_gpio.h>
#include <linux/platform_device.h>
-#include <linux/platform_data/tegra_usb.h>
#include <linux/pm_runtime.h>
#include <linux/slab.h>
#include <linux/usb/ehci_def.h>
@@ -58,7 +57,6 @@
struct tegra_ehci_hcd {
struct tegra_usb_phy *phy;
struct clk *clk;
- struct usb_phy *transceiver;
int port_resuming;
bool needs_double_reset;
enum tegra_usb_phy_port_speed port_speed;
@@ -322,51 +320,16 @@
free_dma_aligned_buffer(urb);
}
-static int setup_vbus_gpio(struct platform_device *pdev,
- struct tegra_ehci_platform_data *pdata)
-{
- int err = 0;
- int gpio;
-
- gpio = pdata->vbus_gpio;
- if (!gpio_is_valid(gpio))
- gpio = of_get_named_gpio(pdev->dev.of_node,
- "nvidia,vbus-gpio", 0);
- if (!gpio_is_valid(gpio))
- return 0;
-
- err = gpio_request(gpio, "vbus_gpio");
- if (err) {
- dev_err(&pdev->dev, "can't request vbus gpio %d", gpio);
- return err;
- }
- err = gpio_direction_output(gpio, 1);
- if (err) {
- dev_err(&pdev->dev, "can't enable vbus\n");
- return err;
- }
-
- return err;
-}
-
static int tegra_ehci_probe(struct platform_device *pdev)
{
struct resource *res;
struct usb_hcd *hcd;
struct ehci_hcd *ehci;
struct tegra_ehci_hcd *tegra;
- struct tegra_ehci_platform_data *pdata;
int err = 0;
int irq;
- struct device_node *np_phy;
struct usb_phy *u_phy;
- pdata = pdev->dev.platform_data;
- if (!pdata) {
- dev_err(&pdev->dev, "Platform data missing\n");
- return -EINVAL;
- }
-
/* Right now device-tree probed devices don't get dma_mask set.
* Since shared usb code relies on it, set it here for now.
* Once we have dma capability bindings this can go away.
@@ -376,14 +339,11 @@
if (!pdev->dev.coherent_dma_mask)
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
- setup_vbus_gpio(pdev, pdata);
-
hcd = usb_create_hcd(&tegra_ehci_hc_driver, &pdev->dev,
dev_name(&pdev->dev));
if (!hcd) {
dev_err(&pdev->dev, "Unable to create HCD\n");
- err = -ENOMEM;
- goto cleanup_vbus_gpio;
+ return -ENOMEM;
}
platform_set_drvdata(pdev, hcd);
ehci = hcd_to_ehci(hcd);
@@ -406,13 +366,7 @@
udelay(1);
tegra_periph_reset_deassert(tegra->clk);
- np_phy = of_parse_phandle(pdev->dev.of_node, "nvidia,phy", 0);
- if (!np_phy) {
- err = -ENODEV;
- goto cleanup_clk_en;
- }
-
- u_phy = tegra_usb_get_phy(np_phy);
+ u_phy = devm_usb_get_phy_by_phandle(&pdev->dev, "nvidia,phy", 0);
if (IS_ERR(u_phy)) {
err = PTR_ERR(u_phy);
goto cleanup_clk_en;
@@ -466,26 +420,18 @@
goto cleanup_phy;
}
- if (pdata->operating_mode == TEGRA_USB_OTG) {
- tegra->transceiver =
- devm_usb_get_phy(&pdev->dev, USB_PHY_TYPE_USB2);
- if (!IS_ERR(tegra->transceiver))
- otg_set_host(tegra->transceiver->otg, &hcd->self);
- } else {
- tegra->transceiver = ERR_PTR(-ENODEV);
- }
+ otg_set_host(u_phy->otg, &hcd->self);
err = usb_add_hcd(hcd, irq, IRQF_SHARED);
if (err) {
dev_err(&pdev->dev, "Failed to add USB HCD\n");
- goto cleanup_transceiver;
+ goto cleanup_otg_set_host;
}
return err;
-cleanup_transceiver:
- if (!IS_ERR(tegra->transceiver))
- otg_set_host(tegra->transceiver->otg, NULL);
+cleanup_otg_set_host:
+ otg_set_host(u_phy->otg, NULL);
cleanup_phy:
usb_phy_shutdown(hcd->phy);
cleanup_clk_en:
@@ -494,8 +440,6 @@
clk_put(tegra->clk);
cleanup_hcd_create:
usb_put_hcd(hcd);
-cleanup_vbus_gpio:
- /* FIXME: Undo setup_vbus_gpio() here */
return err;
}
@@ -505,8 +449,7 @@
struct tegra_ehci_hcd *tegra =
(struct tegra_ehci_hcd *)hcd_to_ehci(hcd)->priv;
- if (!IS_ERR(tegra->transceiver))
- otg_set_host(tegra->transceiver->otg, NULL);
+ otg_set_host(hcd->phy->otg, NULL);
usb_phy_shutdown(hcd->phy);
usb_remove_hcd(hcd);
diff --git a/drivers/usb/musb/am35x.c b/drivers/usb/musb/am35x.c
index 5733a20..5c310c6 100644
--- a/drivers/usb/musb/am35x.c
+++ b/drivers/usb/musb/am35x.c
@@ -218,7 +218,7 @@
struct musb *musb = hci;
void __iomem *reg_base = musb->ctrl_base;
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
struct usb_otg *otg = musb->xceiv->otg;
unsigned long flags;
@@ -335,7 +335,7 @@
static int am35x_musb_set_mode(struct musb *musb, u8 musb_mode)
{
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
int retval = 0;
@@ -350,7 +350,7 @@
static int am35x_musb_init(struct musb *musb)
{
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
void __iomem *reg_base = musb->ctrl_base;
u32 rev;
@@ -394,7 +394,7 @@
static int am35x_musb_exit(struct musb *musb)
{
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
del_timer_sync(&otg_workaround);
@@ -456,7 +456,7 @@
static int am35x_probe(struct platform_device *pdev)
{
- struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct platform_device *musb;
struct am35x_glue *glue;
@@ -577,7 +577,7 @@
static int am35x_suspend(struct device *dev)
{
struct am35x_glue *glue = dev_get_drvdata(dev);
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
/* Shutdown the on-chip PHY and its PLL. */
@@ -593,7 +593,7 @@
static int am35x_resume(struct device *dev)
{
struct am35x_glue *glue = dev_get_drvdata(dev);
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
int ret;
diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c
index 195e966..72e2056 100644
--- a/drivers/usb/musb/blackfin.c
+++ b/drivers/usb/musb/blackfin.c
@@ -451,7 +451,7 @@
static int bfin_probe(struct platform_device *pdev)
{
struct resource musb_resources[2];
- struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct platform_device *musb;
struct bfin_glue *glue;
diff --git a/drivers/usb/musb/cppi_dma.c b/drivers/usb/musb/cppi_dma.c
index 9db211e..904fb85 100644
--- a/drivers/usb/musb/cppi_dma.c
+++ b/drivers/usb/musb/cppi_dma.c
@@ -150,14 +150,11 @@
c->last_processed = NULL;
}
-static int cppi_controller_start(struct dma_controller *c)
+static void cppi_controller_start(struct cppi *controller)
{
- struct cppi *controller;
void __iomem *tibase;
int i;
- controller = container_of(c, struct cppi, controller);
-
/* do whatever is necessary to start controller */
for (i = 0; i < ARRAY_SIZE(controller->tx); i++) {
controller->tx[i].transmit = true;
@@ -212,8 +209,6 @@
/* disable RNDIS mode, also host rx RNDIS autorequest */
musb_writel(tibase, DAVINCI_RNDIS_REG, 0);
musb_writel(tibase, DAVINCI_AUTOREQ_REG, 0);
-
- return 0;
}
/*
@@ -222,14 +217,12 @@
* De-Init the DMA controller as necessary.
*/
-static int cppi_controller_stop(struct dma_controller *c)
+static void cppi_controller_stop(struct cppi *controller)
{
- struct cppi *controller;
void __iomem *tibase;
int i;
struct musb *musb;
- controller = container_of(c, struct cppi, controller);
musb = controller->musb;
tibase = controller->tibase;
@@ -255,8 +248,6 @@
/*disable tx/rx cppi */
musb_writel(tibase, DAVINCI_TXCPPI_CTRL_REG, DAVINCI_DMA_CTRL_DISABLE);
musb_writel(tibase, DAVINCI_RXCPPI_CTRL_REG, DAVINCI_DMA_CTRL_DISABLE);
-
- return 0;
}
/* While dma channel is allocated, we only want the core irqs active
@@ -1321,8 +1312,6 @@
controller->tibase = mregs - DAVINCI_BASE_OFFSET;
controller->musb = musb;
- controller->controller.start = cppi_controller_start;
- controller->controller.stop = cppi_controller_stop;
controller->controller.channel_alloc = cppi_channel_allocate;
controller->controller.channel_release = cppi_channel_release;
controller->controller.channel_program = cppi_channel_program;
@@ -1351,6 +1340,7 @@
controller->irq = irq;
}
+ cppi_controller_start(controller);
return &controller->controller;
}
@@ -1363,6 +1353,8 @@
cppi = container_of(c, struct cppi, controller);
+ cppi_controller_stop(cppi);
+
if (cppi->irq)
free_irq(cppi->irq, cppi->musb);
diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c
index ccc6b63..d9ddf41 100644
--- a/drivers/usb/musb/da8xx.c
+++ b/drivers/usb/musb/da8xx.c
@@ -477,7 +477,7 @@
static int da8xx_probe(struct platform_device *pdev)
{
struct resource musb_resources[2];
- struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct platform_device *musb;
struct da8xx_glue *glue;
diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c
index 91f300e..ed0834e 100644
--- a/drivers/usb/musb/davinci.c
+++ b/drivers/usb/musb/davinci.c
@@ -510,7 +510,7 @@
static int davinci_probe(struct platform_device *pdev)
{
struct resource musb_resources[2];
- struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct platform_device *musb;
struct davinci_glue *glue;
struct clk *clk;
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 29a24ce..b9d7416 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -1764,12 +1764,8 @@
disable_irq_wake(musb->nIrq);
free_irq(musb->nIrq, musb);
}
- if (is_dma_capable() && musb->dma_controller) {
- struct dma_controller *c = musb->dma_controller;
-
- (void) c->stop(c);
- dma_controller_destroy(c);
- }
+ if (musb->dma_controller)
+ dma_controller_destroy(musb->dma_controller);
musb_host_free(musb);
}
@@ -1787,7 +1783,7 @@
{
int status;
struct musb *musb;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
/* The driver might handle more features than the board; OK.
* Fail when the board needs a feature that's not enabled.
@@ -1844,19 +1840,8 @@
pm_runtime_get_sync(musb->controller);
-#ifndef CONFIG_MUSB_PIO_ONLY
- if (use_dma && dev->dma_mask) {
- struct dma_controller *c;
-
- c = dma_controller_create(musb, musb->mregs);
- musb->dma_controller = c;
- if (c)
- (void) c->start(c);
- }
-#endif
- /* ideally this would be abstracted in platform setup */
- if (!is_dma_capable() || !musb->dma_controller)
- dev->dma_mask = NULL;
+ if (use_dma && dev->dma_mask)
+ musb->dma_controller = dma_controller_create(musb, musb->mregs);
/* be sure interrupts are disabled before connecting ISR */
musb_platform_disable(musb);
@@ -1944,6 +1929,8 @@
musb_gadget_cleanup(musb);
fail3:
+ if (musb->dma_controller)
+ dma_controller_destroy(musb->dma_controller);
pm_runtime_put_sync(musb->controller);
fail2:
@@ -2002,9 +1989,6 @@
musb_free(musb);
device_init_wakeup(dev, 0);
-#ifndef CONFIG_MUSB_PIO_ONLY
- dma_set_mask(dev, *dev->parent->dma_mask);
-#endif
return 0;
}
diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h
index 7d341c3..65f3917 100644
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -83,11 +83,6 @@
MUSB_PORT_MODE_DUAL_ROLE,
};
-#ifdef CONFIG_PROC_FS
-#include <linux/fs.h>
-#define MUSB_CONFIG_PROC_FS
-#endif
-
/****************************** CONSTANTS ********************************/
#ifndef MUSB_C_NUM_EPS
@@ -425,9 +420,6 @@
struct musb_hdrc_config *config;
-#ifdef MUSB_CONFIG_PROC_FS
- struct proc_dir_entry *proc_entry;
-#endif
int xceiv_old_state;
#ifdef CONFIG_DEBUG_FS
struct dentry *debugfs_root;
diff --git a/drivers/usb/musb/musb_dma.h b/drivers/usb/musb/musb_dma.h
index 1b6b827..c8e67fd 100644
--- a/drivers/usb/musb/musb_dma.h
+++ b/drivers/usb/musb/musb_dma.h
@@ -62,10 +62,10 @@
#define DMA_ADDR_INVALID (~(dma_addr_t)0)
-#ifndef CONFIG_MUSB_PIO_ONLY
-#define is_dma_capable() (1)
-#else
+#ifdef CONFIG_MUSB_PIO_ONLY
#define is_dma_capable() (0)
+#else
+#define is_dma_capable() (1)
#endif
#ifdef CONFIG_USB_TI_CPPI_DMA
@@ -159,8 +159,6 @@
* Controllers manage dma channels.
*/
struct dma_controller {
- int (*start)(struct dma_controller *);
- int (*stop)(struct dma_controller *);
struct dma_channel *(*channel_alloc)(struct dma_controller *,
struct musb_hw_ep *, u8 is_tx);
void (*channel_release)(struct dma_channel *);
@@ -177,9 +175,20 @@
/* called after channel_program(), may indicate a fault */
extern void musb_dma_completion(struct musb *musb, u8 epnum, u8 transmit);
+#ifdef CONFIG_MUSB_PIO_ONLY
+static inline struct dma_controller *dma_controller_create(struct musb *m,
+ void __iomem *io)
+{
+ return NULL;
+}
+
+static inline void dma_controller_destroy(struct dma_controller *d) { }
+
+#else
extern struct dma_controller *dma_controller_create(struct musb *, void __iomem *);
extern void dma_controller_destroy(struct dma_controller *);
+#endif
#endif /* __MUSB_DMA_H__ */
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 55fe3c2..e7a2cd1 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -46,9 +46,7 @@
#include "musb_core.h"
-#ifdef CONFIG_OF
static const struct of_device_id musb_dsps_of_match[];
-#endif
/**
* avoid using musb_readx()/musb_writex() as glue layer should not be
@@ -75,7 +73,6 @@
u16 revision;
u16 control;
u16 status;
- u16 eoi;
u16 epintr_set;
u16 epintr_clear;
u16 epintr_status;
@@ -205,7 +202,6 @@
dsps_writel(reg_base, wrp->epintr_clear,
wrp->txep_bitmap | wrp->rxep_bitmap);
dsps_writeb(musb->mregs, MUSB_DEVCTL, 0);
- dsps_writel(reg_base, wrp->eoi, 0);
}
static void otg_timer(unsigned long _musb)
@@ -319,7 +315,7 @@
/* Get usb core interrupts */
usbintr = dsps_readl(reg_base, wrp->coreintr_status);
if (!usbintr && !epintr)
- goto eoi;
+ goto out;
musb->int_usb = (usbintr & wrp->usb_bitmap) >> wrp->usb_shift;
if (usbintr)
@@ -387,16 +383,11 @@
if (musb->int_tx || musb->int_rx || musb->int_usb)
ret |= musb_interrupt(musb);
- eoi:
- /* EOI needs to be written for the IRQ to be re-asserted. */
- if (ret == IRQ_HANDLED || epintr || usbintr)
- dsps_writel(reg_base, wrp->eoi, 1);
-
/* Poll for ID change */
if (musb->xceiv->state == OTG_STATE_B_IDLE)
mod_timer(&glue->timer[pdev->id],
jiffies + wrp->poll_seconds * HZ);
-
+out:
spin_unlock_irqrestore(&musb->lock, flags);
return ret;
@@ -428,6 +419,8 @@
goto err0;
}
+ usb_phy_init(musb->xceiv);
+
setup_timer(&glue->timer[pdev->id], otg_timer, (unsigned long) musb);
/* Reset the musb */
@@ -443,9 +436,6 @@
val &= ~(1 << wrp->otg_disable);
dsps_writel(musb->ctrl_base, wrp->phy_utmi, val);
- /* clear level interrupt */
- dsps_writel(reg_base, wrp->eoi, 0);
-
return 0;
err0:
usb_put_phy(musb->xceiv);
@@ -463,6 +453,7 @@
/* Shutdown the on-chip PHY and its PLL. */
musb_dsps_phy_control(glue, pdev->id, 0);
+ usb_phy_shutdown(musb->xceiv);
/* NOP driver needs change if supporting dual instance */
usb_put_phy(musb->xceiv);
@@ -487,7 +478,7 @@
{
struct device *dev = glue->dev;
struct platform_device *pdev = to_platform_device(dev);
- struct musb_hdrc_platform_data *pdata = dev->platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(dev);
struct device_node *np = pdev->dev.of_node;
struct musb_hdrc_config *config;
struct platform_device *musb;
@@ -719,11 +710,10 @@
static SIMPLE_DEV_PM_OPS(dsps_pm_ops, dsps_suspend, dsps_resume);
-static const struct dsps_musb_wrapper ti81xx_driver_data = {
+static const struct dsps_musb_wrapper am33xx_driver_data = {
.revision = 0x00,
.control = 0x14,
.status = 0x18,
- .eoi = 0x24,
.epintr_set = 0x38,
.epintr_clear = 0x40,
.epintr_status = 0x30,
@@ -750,23 +740,12 @@
.instances = 1,
};
-static const struct platform_device_id musb_dsps_id_table[] = {
- {
- .name = "musb-ti81xx",
- .driver_data = (kernel_ulong_t) &ti81xx_driver_data,
- },
- { }, /* Terminating Entry */
-};
-MODULE_DEVICE_TABLE(platform, musb_dsps_id_table);
-
-#ifdef CONFIG_OF
static const struct of_device_id musb_dsps_of_match[] = {
{ .compatible = "ti,musb-am33xx",
- .data = (void *) &ti81xx_driver_data, },
+ .data = (void *) &am33xx_driver_data, },
{ },
};
MODULE_DEVICE_TABLE(of, musb_dsps_of_match);
-#endif
static struct platform_driver dsps_usbss_driver = {
.probe = dsps_probe,
@@ -776,7 +755,6 @@
.pm = &dsps_pm_ops,
.of_match_table = of_match_ptr(musb_dsps_of_match),
},
- .id_table = musb_dsps_id_table,
};
MODULE_DESCRIPTION("TI DSPS MUSB Glue Layer");
diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c
index 0414bc1..96632f9 100644
--- a/drivers/usb/musb/musb_gadget.c
+++ b/drivers/usb/musb/musb_gadget.c
@@ -1266,7 +1266,8 @@
dev_dbg(musb->controller, "req %p queued to %s while ep %s\n",
req, ep->name, "disabled");
status = -ESHUTDOWN;
- goto cleanup;
+ unmap_dma_buffer(request, musb);
+ goto unlock;
}
/* add request to the list */
@@ -1276,7 +1277,7 @@
if (!musb_ep->busy && &request->list == musb_ep->req_list.next)
musb_ep_restart(musb, request);
-cleanup:
+unlock:
spin_unlock_irqrestore(&musb->lock, lockflags);
return status;
}
diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c
index 3d1fd52..e8e9f9a 100644
--- a/drivers/usb/musb/musbhsdma.c
+++ b/drivers/usb/musb/musbhsdma.c
@@ -37,18 +37,10 @@
#include "musb_core.h"
#include "musbhsdma.h"
-static int dma_controller_start(struct dma_controller *c)
-{
- /* nothing to do */
- return 0;
-}
-
static void dma_channel_release(struct dma_channel *channel);
-static int dma_controller_stop(struct dma_controller *c)
+static void dma_controller_stop(struct musb_dma_controller *controller)
{
- struct musb_dma_controller *controller = container_of(c,
- struct musb_dma_controller, controller);
struct musb *musb = controller->private_data;
struct dma_channel *channel;
u8 bit;
@@ -67,8 +59,6 @@
}
}
}
-
- return 0;
}
static struct dma_channel *dma_channel_allocate(struct dma_controller *c,
@@ -371,8 +361,7 @@
struct musb_dma_controller *controller = container_of(c,
struct musb_dma_controller, controller);
- if (!controller)
- return;
+ dma_controller_stop(controller);
if (controller->irq)
free_irq(controller->irq, c);
@@ -400,8 +389,6 @@
controller->private_data = musb;
controller->base = base;
- controller->controller.start = dma_controller_start;
- controller->controller.stop = dma_controller_stop;
controller->controller.channel_alloc = dma_channel_allocate;
controller->controller.channel_release = dma_channel_release;
controller->controller.channel_program = dma_channel_program;
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index 6708a3b..ebb46ec 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -255,7 +255,7 @@
{
struct musb *musb = glue_to_musb(glue);
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *pdata = dev->platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(dev);
struct omap_musb_board_data *data = pdata->board_data;
struct usb_otg *otg = musb->xceiv->otg;
@@ -341,7 +341,7 @@
int status = 0;
struct device *dev = musb->controller;
struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
/* We require some kind of external transceiver, hooked
@@ -412,7 +412,7 @@
unsigned long timeout = jiffies + msecs_to_jiffies(1000);
struct device *dev = musb->controller;
struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
- struct musb_hdrc_platform_data *pdata = dev->platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(dev);
struct omap_musb_board_data *data = pdata->board_data;
switch (glue->status) {
@@ -482,7 +482,7 @@
static int omap2430_probe(struct platform_device *pdev)
{
struct resource musb_resources[2];
- struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct omap_musb_board_data *data;
struct platform_device *musb;
struct omap2430_glue *glue;
diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c
index 20f182c..0d68fc1 100644
--- a/drivers/usb/musb/tusb6010.c
+++ b/drivers/usb/musb/tusb6010.c
@@ -1157,7 +1157,7 @@
static int tusb_probe(struct platform_device *pdev)
{
struct resource musb_resources[2];
- struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct platform_device *musb;
struct tusb6010_glue *glue;
diff --git a/drivers/usb/musb/tusb6010_omap.c b/drivers/usb/musb/tusb6010_omap.c
index 98df17c..b8794eb 100644
--- a/drivers/usb/musb/tusb6010_omap.c
+++ b/drivers/usb/musb/tusb6010_omap.c
@@ -66,28 +66,6 @@
unsigned multichannel:1;
};
-static int tusb_omap_dma_start(struct dma_controller *c)
-{
- struct tusb_omap_dma *tusb_dma;
-
- tusb_dma = container_of(c, struct tusb_omap_dma, controller);
-
- /* dev_dbg(musb->controller, "ep%i ch: %i\n", chdat->epnum, chdat->ch); */
-
- return 0;
-}
-
-static int tusb_omap_dma_stop(struct dma_controller *c)
-{
- struct tusb_omap_dma *tusb_dma;
-
- tusb_dma = container_of(c, struct tusb_omap_dma, controller);
-
- /* dev_dbg(musb->controller, "ep%i ch: %i\n", chdat->epnum, chdat->ch); */
-
- return 0;
-}
-
/*
* Allocate dmareq0 to the current channel unless it's already taken
*/
@@ -695,8 +673,6 @@
tusb_dma->dmareq = -1;
tusb_dma->sync_dev = -1;
- tusb_dma->controller.start = tusb_omap_dma_start;
- tusb_dma->controller.stop = tusb_omap_dma_stop;
tusb_dma->controller.channel_alloc = tusb_omap_dma_allocate;
tusb_dma->controller.channel_release = tusb_omap_dma_release;
tusb_dma->controller.channel_program = tusb_omap_dma_program;
diff --git a/drivers/usb/musb/ux500.c b/drivers/usb/musb/ux500.c
index fce71b6..59256b1 100644
--- a/drivers/usb/musb/ux500.c
+++ b/drivers/usb/musb/ux500.c
@@ -227,7 +227,7 @@
static int ux500_probe(struct platform_device *pdev)
{
struct resource musb_resources[2];
- struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
+ struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct device_node *np = pdev->dev.of_node;
struct platform_device *musb;
struct ux500_glue *glue;
diff --git a/drivers/usb/musb/ux500_dma.c b/drivers/usb/musb/ux500_dma.c
index bfb7a65..e51dd9b 100644
--- a/drivers/usb/musb/ux500_dma.c
+++ b/drivers/usb/musb/ux500_dma.c
@@ -254,10 +254,8 @@
return 0;
}
-static int ux500_dma_controller_stop(struct dma_controller *c)
+static void ux500_dma_controller_stop(struct ux500_dma_controller *controller)
{
- struct ux500_dma_controller *controller = container_of(c,
- struct ux500_dma_controller, controller);
struct ux500_dma_channel *ux500_channel;
struct dma_channel *channel;
u8 ch_num;
@@ -281,18 +279,14 @@
if (ux500_channel->dma_chan)
dma_release_channel(ux500_channel->dma_chan);
}
-
- return 0;
}
-static int ux500_dma_controller_start(struct dma_controller *c)
+static int ux500_dma_controller_start(struct ux500_dma_controller *controller)
{
- struct ux500_dma_controller *controller = container_of(c,
- struct ux500_dma_controller, controller);
struct ux500_dma_channel *ux500_channel = NULL;
struct musb *musb = controller->private_data;
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct ux500_musb_board_data *data;
struct dma_channel *dma_channel = NULL;
char **chan_names;
@@ -347,7 +341,7 @@
dir, ch_num);
/* Release already allocated channels */
- ux500_dma_controller_stop(c);
+ ux500_dma_controller_stop(controller);
return -EBUSY;
}
@@ -369,6 +363,7 @@
struct ux500_dma_controller *controller = container_of(c,
struct ux500_dma_controller, controller);
+ ux500_dma_controller_stop(controller);
kfree(controller);
}
@@ -378,6 +373,7 @@
struct ux500_dma_controller *controller;
struct platform_device *pdev = to_platform_device(musb->controller);
struct resource *iomem;
+ int ret;
controller = kzalloc(sizeof(*controller), GFP_KERNEL);
if (!controller)
@@ -394,14 +390,15 @@
controller->phy_base = (dma_addr_t) iomem->start;
- controller->controller.start = ux500_dma_controller_start;
- controller->controller.stop = ux500_dma_controller_stop;
controller->controller.channel_alloc = ux500_dma_channel_allocate;
controller->controller.channel_release = ux500_dma_channel_release;
controller->controller.channel_program = ux500_dma_channel_program;
controller->controller.channel_abort = ux500_dma_channel_abort;
controller->controller.is_compatible = ux500_dma_is_compatible;
+ ret = ux500_dma_controller_start(controller);
+ if (ret)
+ goto plat_get_fail;
return &controller->controller;
plat_get_fail:
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 3622fff..f5ea339 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -1,22 +1,10 @@
#
# Physical Layer USB driver configuration
#
-menuconfig USB_PHY
- bool "USB Physical Layer drivers"
- help
- Most USB controllers have the physical layer signalling part
- (commonly called a PHY) built in. However, dual-role devices
- (a.k.a. USB on-the-go) which support being USB master or slave
- with the same connector often use an external PHY.
+menu "USB Physical Layer drivers"
- The drivers in this submenu add support for such PHY devices.
- They are not needed for standard master-only (or the vast
- majority of slave-only) USB interfaces.
-
- If you're not sure if this applies to you, it probably doesn't;
- say N here.
-
-if USB_PHY
+config USB_PHY
+ def_bool n
#
# USB Transceiver Drivers
@@ -24,6 +12,7 @@
config AB8500_USB
tristate "AB8500 USB Transceiver Driver"
depends on AB8500_CORE
+ select USB_PHY
help
Enable this to support the USB OTG transceiver in AB8500 chip.
This transceiver supports high and full speed devices plus,
@@ -33,12 +22,14 @@
bool "Freescale USB OTG Transceiver Driver"
depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME
select USB_OTG
+ select USB_PHY
help
Enable this to support Freescale USB OTG transceiver.
config ISP1301_OMAP
tristate "Philips ISP1301 with OMAP OTG"
depends on I2C && ARCH_OMAP_OTG
+ select USB_PHY
help
If you say yes here you get support for the Philips ISP1301
USB-On-The-Go transceiver working with the OMAP OTG controller.
@@ -52,12 +43,14 @@
config MV_U3D_PHY
bool "Marvell USB 3.0 PHY controller Driver"
depends on CPU_MMP3
+ select USB_PHY
help
Enable this to support Marvell USB 3.0 phy controller for Marvell
SoC.
config NOP_USB_XCEIV
tristate "NOP USB Transceiver Driver"
+ select USB_PHY
help
This driver is to be used by all the usb transceiver which are either
built-in with usb ip or which are autonomous and doesn't require any
@@ -76,6 +69,7 @@
tristate "OMAP USB2 PHY Driver"
depends on ARCH_OMAP2PLUS
select OMAP_CONTROL_USB
+ select USB_PHY
help
Enable this to support the transceiver that is part of SOC. This
driver takes care of all the PHY functionality apart from comparator.
@@ -85,6 +79,7 @@
config OMAP_USB3
tristate "OMAP USB3 PHY Driver"
select OMAP_CONTROL_USB
+ select USB_PHY
help
Enable this to support the USB3 PHY that is part of SOC. This
driver takes care of all the PHY functionality apart from comparator.
@@ -101,6 +96,7 @@
config SAMSUNG_USB2PHY
tristate "Samsung USB 2.0 PHY controller Driver"
select SAMSUNG_USBPHY
+ select USB_PHY
help
Enable this to support Samsung USB 2.0 (High Speed) PHY controller
driver for Samsung SoCs.
@@ -108,6 +104,7 @@
config SAMSUNG_USB3PHY
tristate "Samsung USB 3.0 PHY controller Driver"
select SAMSUNG_USBPHY
+ select USB_PHY
help
Enable this to support Samsung USB 3.0 (Super Speed) phy controller
for samsung SoCs.
@@ -115,6 +112,7 @@
config TWL4030_USB
tristate "TWL4030 USB Transceiver Driver"
depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
+ select USB_PHY
help
Enable this to support the USB OTG transceiver on TWL4030
family chips (including the TWL5030 and TPS659x0 devices).
@@ -135,6 +133,7 @@
config USB_GPIO_VBUS
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
depends on GPIOLIB
+ select USB_PHY
help
Provides simple GPIO VBUS sensing for controllers with an
internal transceiver via the usb_phy interface, and
@@ -145,6 +144,7 @@
tristate "NXP ISP1301 USB transceiver support"
depends on USB || USB_GADGET
depends on I2C
+ select USB_PHY
help
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
This chip is typically used as USB transceiver for USB host, gadget
@@ -156,6 +156,7 @@
config USB_MSM_OTG
tristate "OTG support for Qualcomm on-chip USB controller"
depends on (USB || USB_GADGET) && ARCH_MSM
+ select USB_PHY
help
Enable this to support the USB OTG transceiver on MSM chips. It
handles PHY initialization, clock management, and workarounds
@@ -169,6 +170,7 @@
tristate "Marvell USB OTG support"
depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
select USB_OTG
+ select USB_PHY
help
Say Y here if you want to build Marvell USB OTG transciever
driver in kernel (including PXA and MMP series). This driver
@@ -180,6 +182,7 @@
tristate "Freescale MXS USB PHY support"
depends on ARCH_MXC || ARCH_MXS
select STMP_DEVICE
+ select USB_PHY
help
Enable this to support the Freescale MXS USB PHY.
@@ -188,6 +191,7 @@
config USB_RCAR_PHY
tristate "Renesas R-Car USB PHY support"
depends on USB || USB_GADGET
+ select USB_PHY
help
Say Y here to add support for the Renesas R-Car USB common PHY driver.
This chip is typically used as USB PHY for USB host, gadget.
@@ -210,4 +214,4 @@
Provides read/write operations to the ULPI phy register set for
controllers with a viewport register (e.g. Chipidea/ARC controllers).
-endif # USB_PHY
+endmenu
diff --git a/drivers/usb/phy/phy-fsl-usb.c b/drivers/usb/phy/phy-fsl-usb.c
index e771baf..e965cf6 100644
--- a/drivers/usb/phy/phy-fsl-usb.c
+++ b/drivers/usb/phy/phy-fsl-usb.c
@@ -834,7 +834,7 @@
int status;
struct resource *res;
u32 temp;
- struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
+ struct fsl_usb2_platform_data *pdata = dev_get_platdata(&pdev->dev);
p_otg = container_of(otg_trans, struct fsl_otg, phy);
fsm = &p_otg->fsm;
@@ -1105,7 +1105,7 @@
{
int ret;
- if (!pdev->dev.platform_data)
+ if (!dev_get_platdata(&pdev->dev))
return -ENODEV;
/* configure the OTG */
@@ -1137,7 +1137,7 @@
static int fsl_otg_remove(struct platform_device *pdev)
{
- struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
+ struct fsl_usb2_platform_data *pdata = dev_get_platdata(&pdev->dev);
usb_remove_phy(&fsl_otg_dev->phy);
free_irq(fsl_otg_dev->irq, fsl_otg_dev);
diff --git a/drivers/usb/phy/phy-generic.c b/drivers/usb/phy/phy-generic.c
index f379b7d..406f8e4 100644
--- a/drivers/usb/phy/phy-generic.c
+++ b/drivers/usb/phy/phy-generic.c
@@ -142,7 +142,8 @@
static int usb_phy_gen_xceiv_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
- struct usb_phy_gen_xceiv_platform_data *pdata = pdev->dev.platform_data;
+ struct usb_phy_gen_xceiv_platform_data *pdata =
+ dev_get_platdata(&pdev->dev);
struct usb_phy_gen_xceiv *nop;
enum usb_phy_type type = USB_PHY_TYPE_USB2;
int err;
diff --git a/drivers/usb/phy/phy-gpio-vbus-usb.c b/drivers/usb/phy/phy-gpio-vbus-usb.c
index 8443335..b2f29c9 100644
--- a/drivers/usb/phy/phy-gpio-vbus-usb.c
+++ b/drivers/usb/phy/phy-gpio-vbus-usb.c
@@ -101,7 +101,7 @@
{
struct gpio_vbus_data *gpio_vbus =
container_of(work, struct gpio_vbus_data, work.work);
- struct gpio_vbus_mach_info *pdata = gpio_vbus->dev->platform_data;
+ struct gpio_vbus_mach_info *pdata = dev_get_platdata(gpio_vbus->dev);
int gpio, status, vbus;
if (!gpio_vbus->phy.otg->gadget)
@@ -155,7 +155,7 @@
static irqreturn_t gpio_vbus_irq(int irq, void *data)
{
struct platform_device *pdev = data;
- struct gpio_vbus_mach_info *pdata = pdev->dev.platform_data;
+ struct gpio_vbus_mach_info *pdata = dev_get_platdata(&pdev->dev);
struct gpio_vbus_data *gpio_vbus = platform_get_drvdata(pdev);
struct usb_otg *otg = gpio_vbus->phy.otg;
@@ -182,7 +182,7 @@
gpio_vbus = container_of(otg->phy, struct gpio_vbus_data, phy);
pdev = to_platform_device(gpio_vbus->dev);
- pdata = gpio_vbus->dev->platform_data;
+ pdata = dev_get_platdata(gpio_vbus->dev);
gpio = pdata->gpio_pullup;
if (!gadget) {
@@ -243,7 +243,7 @@
static int __init gpio_vbus_probe(struct platform_device *pdev)
{
- struct gpio_vbus_mach_info *pdata = pdev->dev.platform_data;
+ struct gpio_vbus_mach_info *pdata = dev_get_platdata(&pdev->dev);
struct gpio_vbus_data *gpio_vbus;
struct resource *res;
int err, gpio, irq;
@@ -352,7 +352,7 @@
static int __exit gpio_vbus_remove(struct platform_device *pdev)
{
struct gpio_vbus_data *gpio_vbus = platform_get_drvdata(pdev);
- struct gpio_vbus_mach_info *pdata = pdev->dev.platform_data;
+ struct gpio_vbus_mach_info *pdata = dev_get_platdata(&pdev->dev);
int gpio = pdata->gpio_vbus;
device_init_wakeup(&pdev->dev, 0);
diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c
index d08f334..e9d4cd9 100644
--- a/drivers/usb/phy/phy-msm-usb.c
+++ b/drivers/usb/phy/phy-msm-usb.c
@@ -1419,7 +1419,7 @@
struct usb_phy *phy;
dev_info(&pdev->dev, "msm_otg probe\n");
- if (!pdev->dev.platform_data) {
+ if (!dev_get_platdata(&pdev->dev)) {
dev_err(&pdev->dev, "No platform data given. Bailing out\n");
return -ENODEV;
}
@@ -1436,7 +1436,7 @@
return -ENOMEM;
}
- motg->pdata = pdev->dev.platform_data;
+ motg->pdata = dev_get_platdata(&pdev->dev);
phy = &motg->phy;
phy->dev = &pdev->dev;
diff --git a/drivers/usb/phy/phy-mv-u3d-usb.c b/drivers/usb/phy/phy-mv-u3d-usb.c
index 1568ea6..d317903 100644
--- a/drivers/usb/phy/phy-mv-u3d-usb.c
+++ b/drivers/usb/phy/phy-mv-u3d-usb.c
@@ -82,7 +82,7 @@
writel_relaxed(value, data);
}
-void mv_u3d_phy_shutdown(struct usb_phy *phy)
+static void mv_u3d_phy_shutdown(struct usb_phy *phy)
{
struct mv_u3d_phy *mv_u3d_phy;
void __iomem *base;
@@ -271,7 +271,7 @@
void __iomem *phy_base;
int ret;
- pdata = pdev->dev.platform_data;
+ pdata = dev_get_platdata(&pdev->dev);
if (!pdata) {
dev_err(&pdev->dev, "%s: no platform data defined\n", __func__);
return -EINVAL;
diff --git a/drivers/usb/phy/phy-mv-usb.c b/drivers/usb/phy/phy-mv-usb.c
index 4a6b03c..98f6ac6a 100644
--- a/drivers/usb/phy/phy-mv-usb.c
+++ b/drivers/usb/phy/phy-mv-usb.c
@@ -653,7 +653,7 @@
.attrs = inputs_attrs,
};
-int mv_otg_remove(struct platform_device *pdev)
+static int mv_otg_remove(struct platform_device *pdev)
{
struct mv_otg *mvotg = platform_get_drvdata(pdev);
@@ -673,7 +673,7 @@
static int mv_otg_probe(struct platform_device *pdev)
{
- struct mv_usb_platform_data *pdata = pdev->dev.platform_data;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct mv_otg *mvotg;
struct usb_otg *otg;
struct resource *r;
@@ -893,7 +893,7 @@
static struct platform_driver mv_otg_driver = {
.probe = mv_otg_probe,
- .remove = __exit_p(mv_otg_remove),
+ .remove = mv_otg_remove,
.driver = {
.owner = THIS_MODULE,
.name = driver_name,
diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c
index bd601c5..fdd33b4 100644
--- a/drivers/usb/phy/phy-mxs-usb.c
+++ b/drivers/usb/phy/phy-mxs-usb.c
@@ -41,11 +41,14 @@
#define to_mxs_phy(p) container_of((p), struct mxs_phy, phy)
-static void mxs_phy_hw_init(struct mxs_phy *mxs_phy)
+static int mxs_phy_hw_init(struct mxs_phy *mxs_phy)
{
+ int ret;
void __iomem *base = mxs_phy->phy.io_priv;
- stmp_reset_block(base + HW_USBPHY_CTRL);
+ ret = stmp_reset_block(base + HW_USBPHY_CTRL);
+ if (ret)
+ return ret;
/* Power up the PHY */
writel(0, base + HW_USBPHY_PWD);
@@ -54,6 +57,8 @@
writel(BM_USBPHY_CTRL_ENUTMILEVEL2 |
BM_USBPHY_CTRL_ENUTMILEVEL3,
base + HW_USBPHY_CTRL_SET);
+
+ return 0;
}
static int mxs_phy_init(struct usb_phy *phy)
@@ -61,9 +66,7 @@
struct mxs_phy *mxs_phy = to_mxs_phy(phy);
clk_prepare_enable(mxs_phy->clk);
- mxs_phy_hw_init(mxs_phy);
-
- return 0;
+ return mxs_phy_hw_init(mxs_phy);
}
static void mxs_phy_shutdown(struct usb_phy *phy)
diff --git a/drivers/usb/phy/phy-omap-control.c b/drivers/usb/phy/phy-omap-control.c
index 1419ced..a4dda8e 100644
--- a/drivers/usb/phy/phy-omap-control.c
+++ b/drivers/usb/phy/phy-omap-control.c
@@ -197,7 +197,8 @@
{
struct resource *res;
struct device_node *np = pdev->dev.of_node;
- struct omap_control_usb_platform_data *pdata = pdev->dev.platform_data;
+ struct omap_control_usb_platform_data *pdata =
+ dev_get_platdata(&pdev->dev);
control_usb = devm_kzalloc(&pdev->dev, sizeof(*control_usb),
GFP_KERNEL);
diff --git a/drivers/usb/phy/phy-omap-usb3.c b/drivers/usb/phy/phy-omap-usb3.c
index a2fb30b..fc15694 100644
--- a/drivers/usb/phy/phy-omap-usb3.c
+++ b/drivers/usb/phy/phy-omap-usb3.c
@@ -27,7 +27,6 @@
#include <linux/delay.h>
#include <linux/usb/omap_control_usb.h>
-#define NUM_SYS_CLKS 6
#define PLL_STATUS 0x00000004
#define PLL_GO 0x00000008
#define PLL_CONFIGURATION1 0x0000000C
@@ -57,26 +56,32 @@
*/
# define PLL_IDLE_TIME 100;
-enum sys_clk_rate {
- CLK_RATE_UNDEFINED = -1,
- CLK_RATE_12MHZ,
- CLK_RATE_16MHZ,
- CLK_RATE_19MHZ,
- CLK_RATE_20MHZ,
- CLK_RATE_26MHZ,
- CLK_RATE_38MHZ
+struct usb_dpll_map {
+ unsigned long rate;
+ struct usb_dpll_params params;
};
-static struct usb_dpll_params omap_usb3_dpll_params[NUM_SYS_CLKS] = {
- {1250, 5, 4, 20, 0}, /* 12 MHz */
- {3125, 20, 4, 20, 0}, /* 16.8 MHz */
- {1172, 8, 4, 20, 65537}, /* 19.2 MHz */
- {1000, 7, 4, 10, 0}, /* 20 MHz */
- {1250, 12, 4, 20, 0}, /* 26 MHz */
- {3125, 47, 4, 20, 92843}, /* 38.4 MHz */
-
+static struct usb_dpll_map dpll_map[] = {
+ {12000000, {1250, 5, 4, 20, 0} }, /* 12 MHz */
+ {16800000, {3125, 20, 4, 20, 0} }, /* 16.8 MHz */
+ {19200000, {1172, 8, 4, 20, 65537} }, /* 19.2 MHz */
+ {20000000, {1000, 7, 4, 10, 0} }, /* 20 MHz */
+ {26000000, {1250, 12, 4, 20, 0} }, /* 26 MHz */
+ {38400000, {3125, 47, 4, 20, 92843} }, /* 38.4 MHz */
};
+static struct usb_dpll_params *omap_usb3_get_dpll_params(unsigned long rate)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(dpll_map); i++) {
+ if (rate == dpll_map[i].rate)
+ return &dpll_map[i].params;
+ }
+
+ return 0;
+}
+
static int omap_usb3_suspend(struct usb_phy *x, int suspend)
{
struct omap_usb *phy = phy_to_omapusb(x);
@@ -116,26 +121,6 @@
return 0;
}
-static inline enum sys_clk_rate __get_sys_clk_index(unsigned long rate)
-{
- switch (rate) {
- case 12000000:
- return CLK_RATE_12MHZ;
- case 16800000:
- return CLK_RATE_16MHZ;
- case 19200000:
- return CLK_RATE_19MHZ;
- case 20000000:
- return CLK_RATE_20MHZ;
- case 26000000:
- return CLK_RATE_26MHZ;
- case 38400000:
- return CLK_RATE_38MHZ;
- default:
- return CLK_RATE_UNDEFINED;
- }
-}
-
static void omap_usb_dpll_relock(struct omap_usb *phy)
{
u32 val;
@@ -155,39 +140,39 @@
{
u32 val;
unsigned long rate;
- enum sys_clk_rate clk_index;
+ struct usb_dpll_params *dpll_params;
- rate = clk_get_rate(phy->sys_clk);
- clk_index = __get_sys_clk_index(rate);
-
- if (clk_index == CLK_RATE_UNDEFINED) {
- pr_err("dpll cannot be locked for sys clk freq:%luHz\n", rate);
+ rate = clk_get_rate(phy->sys_clk);
+ dpll_params = omap_usb3_get_dpll_params(rate);
+ if (!dpll_params) {
+ dev_err(phy->dev,
+ "No DPLL configuration for %lu Hz SYS CLK\n", rate);
return -EINVAL;
}
val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
val &= ~PLL_REGN_MASK;
- val |= omap_usb3_dpll_params[clk_index].n << PLL_REGN_SHIFT;
+ val |= dpll_params->n << PLL_REGN_SHIFT;
omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
val &= ~PLL_SELFREQDCO_MASK;
- val |= omap_usb3_dpll_params[clk_index].freq << PLL_SELFREQDCO_SHIFT;
+ val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
val &= ~PLL_REGM_MASK;
- val |= omap_usb3_dpll_params[clk_index].m << PLL_REGM_SHIFT;
+ val |= dpll_params->m << PLL_REGM_SHIFT;
omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION4);
val &= ~PLL_REGM_F_MASK;
- val |= omap_usb3_dpll_params[clk_index].mf << PLL_REGM_F_SHIFT;
+ val |= dpll_params->mf << PLL_REGM_F_SHIFT;
omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION4, val);
val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION3);
val &= ~PLL_SD_MASK;
- val |= omap_usb3_dpll_params[clk_index].sd << PLL_SD_SHIFT;
+ val |= dpll_params->sd << PLL_SD_SHIFT;
omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION3, val);
omap_usb_dpll_relock(phy);
@@ -198,8 +183,12 @@
static int omap_usb3_init(struct usb_phy *x)
{
struct omap_usb *phy = phy_to_omapusb(x);
+ int ret;
- omap_usb_dpll_lock(phy);
+ ret = omap_usb_dpll_lock(phy);
+ if (ret)
+ return ret;
+
omap_control_usb3_phy_power(phy->control_dev, 1);
return 0;
diff --git a/drivers/usb/phy/phy-rcar-usb.c b/drivers/usb/phy/phy-rcar-usb.c
index ae90940..33265a5 100644
--- a/drivers/usb/phy/phy-rcar-usb.c
+++ b/drivers/usb/phy/phy-rcar-usb.c
@@ -83,7 +83,7 @@
{
struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
struct device *dev = phy->dev;
- struct rcar_phy_platform_data *pdata = dev->platform_data;
+ struct rcar_phy_platform_data *pdata = dev_get_platdata(dev);
void __iomem *reg0 = priv->reg0;
void __iomem *reg1 = priv->reg1;
static const u8 ovcn_act[] = { OVC0_ACT, OVC1_ACT, OVC2_ACT };
@@ -184,17 +184,12 @@
void __iomem *reg0, *reg1 = NULL;
int ret;
- if (!pdev->dev.platform_data) {
+ if (!dev_get_platdata(&pdev->dev)) {
dev_err(dev, "No platform data\n");
return -EINVAL;
}
res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res0) {
- dev_err(dev, "Not enough platform resources\n");
- return -EINVAL;
- }
-
reg0 = devm_ioremap_resource(dev, res0);
if (IS_ERR(reg0))
return PTR_ERR(reg0);
diff --git a/drivers/usb/phy/phy-samsung-usb2.c b/drivers/usb/phy/phy-samsung-usb2.c
index 758b86d..ff70e4b 100644
--- a/drivers/usb/phy/phy-samsung-usb2.c
+++ b/drivers/usb/phy/phy-samsung-usb2.c
@@ -359,7 +359,7 @@
{
struct samsung_usbphy *sphy;
struct usb_otg *otg;
- struct samsung_usbphy_data *pdata = pdev->dev.platform_data;
+ struct samsung_usbphy_data *pdata = dev_get_platdata(&pdev->dev);
const struct samsung_usbphy_drvdata *drv_data;
struct device *dev = &pdev->dev;
struct resource *phy_mem;
diff --git a/drivers/usb/phy/phy-samsung-usb3.c b/drivers/usb/phy/phy-samsung-usb3.c
index 300e0cf..c6eb222 100644
--- a/drivers/usb/phy/phy-samsung-usb3.c
+++ b/drivers/usb/phy/phy-samsung-usb3.c
@@ -231,7 +231,7 @@
static int samsung_usb3phy_probe(struct platform_device *pdev)
{
struct samsung_usbphy *sphy;
- struct samsung_usbphy_data *pdata = pdev->dev.platform_data;
+ struct samsung_usbphy_data *pdata = dev_get_platdata(&pdev->dev);
struct device *dev = &pdev->dev;
struct resource *phy_mem;
void __iomem *phy_base;
diff --git a/drivers/usb/phy/phy-tegra-usb.c b/drivers/usb/phy/phy-tegra-usb.c
index cec0855..49fa2da 100644
--- a/drivers/usb/phy/phy-tegra-usb.c
+++ b/drivers/usb/phy/phy-tegra-usb.c
@@ -31,9 +31,11 @@
#include <linux/of_gpio.h>
#include <linux/usb/otg.h>
#include <linux/usb/ulpi.h>
+#include <linux/usb/of.h>
#include <asm/mach-types.h>
#include <linux/usb/ehci_def.h>
#include <linux/usb/tegra_usb_phy.h>
+#include <linux/regulator/consumer.h>
#define ULPI_VIEWPORT 0x170
@@ -184,27 +186,6 @@
},
};
-static struct tegra_utmip_config utmip_default[] = {
- [0] = {
- .hssync_start_delay = 9,
- .idle_wait_delay = 17,
- .elastic_limit = 16,
- .term_range_adj = 6,
- .xcvr_setup = 9,
- .xcvr_lsfslew = 1,
- .xcvr_lsrslew = 1,
- },
- [2] = {
- .hssync_start_delay = 9,
- .idle_wait_delay = 17,
- .elastic_limit = 16,
- .term_range_adj = 6,
- .xcvr_setup = 9,
- .xcvr_lsfslew = 2,
- .xcvr_lsrslew = 2,
- },
-};
-
static void set_pts(struct tegra_usb_phy *phy, u8 pts_val)
{
void __iomem *base = phy->regs;
@@ -231,7 +212,7 @@
static int utmip_pad_open(struct tegra_usb_phy *phy)
{
- phy->pad_clk = devm_clk_get(phy->dev, "utmi-pads");
+ phy->pad_clk = devm_clk_get(phy->u_phy.dev, "utmi-pads");
if (IS_ERR(phy->pad_clk)) {
pr_err("%s: can't get utmip pad clock\n", __func__);
return PTR_ERR(phy->pad_clk);
@@ -396,7 +377,7 @@
UTMIP_PLLU_ENABLE_DLY_COUNT(phy->freq->enable_delay);
writel(val, base + UTMIP_PLL_CFG1);
- if (phy->mode == TEGRA_USB_PHY_MODE_DEVICE) {
+ if (phy->mode == USB_DR_MODE_PERIPHERAL) {
val = readl(base + USB_SUSP_CTRL);
val &= ~(USB_WAKE_ON_CNNT_EN_DEV | USB_WAKE_ON_DISCON_EN_DEV);
writel(val, base + USB_SUSP_CTRL);
@@ -431,7 +412,7 @@
if (phy->is_legacy_phy) {
val = readl(base + UTMIP_SPARE_CFG0);
- if (phy->mode == TEGRA_USB_PHY_MODE_DEVICE)
+ if (phy->mode == USB_DR_MODE_PERIPHERAL)
val &= ~FUSE_SETUP_SEL;
else
val |= FUSE_SETUP_SEL;
@@ -472,7 +453,7 @@
utmi_phy_clk_disable(phy);
- if (phy->mode == TEGRA_USB_PHY_MODE_DEVICE) {
+ if (phy->mode == USB_DR_MODE_PERIPHERAL) {
val = readl(base + USB_SUSP_CTRL);
val &= ~USB_WAKEUP_DEBOUNCE_COUNT(~0);
val |= USB_WAKE_ON_CNNT_EN_DEV | USB_WAKEUP_DEBOUNCE_COUNT(5);
@@ -560,13 +541,15 @@
ret = gpio_direction_output(phy->reset_gpio, 0);
if (ret < 0) {
- dev_err(phy->dev, "gpio %d not set to 0\n", phy->reset_gpio);
+ dev_err(phy->u_phy.dev, "gpio %d not set to 0\n",
+ phy->reset_gpio);
return ret;
}
msleep(5);
ret = gpio_direction_output(phy->reset_gpio, 1);
if (ret < 0) {
- dev_err(phy->dev, "gpio %d not set to 1\n", phy->reset_gpio);
+ dev_err(phy->u_phy.dev, "gpio %d not set to 1\n",
+ phy->reset_gpio);
return ret;
}
@@ -634,6 +617,9 @@
{
struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy);
+ if (!IS_ERR(phy->vbus))
+ regulator_disable(phy->vbus);
+
clk_disable_unprepare(phy->pll_u);
}
@@ -666,29 +652,30 @@
{
int err;
- phy->clk = devm_clk_get(phy->dev, "ulpi-link");
+ phy->clk = devm_clk_get(phy->u_phy.dev, "ulpi-link");
if (IS_ERR(phy->clk)) {
pr_err("%s: can't get ulpi clock\n", __func__);
return PTR_ERR(phy->clk);
}
- err = devm_gpio_request(phy->dev, phy->reset_gpio, "ulpi_phy_reset_b");
+ err = devm_gpio_request(phy->u_phy.dev, phy->reset_gpio,
+ "ulpi_phy_reset_b");
if (err < 0) {
- dev_err(phy->dev, "request failed for gpio: %d\n",
+ dev_err(phy->u_phy.dev, "request failed for gpio: %d\n",
phy->reset_gpio);
return err;
}
err = gpio_direction_output(phy->reset_gpio, 0);
if (err < 0) {
- dev_err(phy->dev, "gpio %d direction not set to output\n",
+ dev_err(phy->u_phy.dev, "gpio %d direction not set to output\n",
phy->reset_gpio);
return err;
}
phy->ulpi = otg_ulpi_create(&ulpi_viewport_access_ops, 0);
if (!phy->ulpi) {
- dev_err(phy->dev, "otg_ulpi_create returned NULL\n");
+ dev_err(phy->u_phy.dev, "otg_ulpi_create returned NULL\n");
err = -ENOMEM;
return err;
}
@@ -703,14 +690,7 @@
int i;
int err;
- if (!phy->is_ulpi_phy) {
- if (phy->is_legacy_phy)
- phy->config = &utmip_default[0];
- else
- phy->config = &utmip_default[2];
- }
-
- phy->pll_u = devm_clk_get(phy->dev, "pll_u");
+ phy->pll_u = devm_clk_get(phy->u_phy.dev, "pll_u");
if (IS_ERR(phy->pll_u)) {
pr_err("Can't get pll_u clock\n");
return PTR_ERR(phy->pll_u);
@@ -733,6 +713,16 @@
goto fail;
}
+ if (!IS_ERR(phy->vbus)) {
+ err = regulator_enable(phy->vbus);
+ if (err) {
+ dev_err(phy->u_phy.dev,
+ "failed to enable usb vbus regulator: %d\n",
+ err);
+ goto fail;
+ }
+ }
+
if (phy->is_ulpi_phy)
err = ulpi_open(phy);
else
@@ -784,11 +774,94 @@
}
EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_end);
+static int read_utmi_param(struct platform_device *pdev, const char *param,
+ u8 *dest)
+{
+ u32 value;
+ int err = of_property_read_u32(pdev->dev.of_node, param, &value);
+ *dest = (u8)value;
+ if (err < 0)
+ dev_err(&pdev->dev, "Failed to read USB UTMI parameter %s: %d\n",
+ param, err);
+ return err;
+}
+
+static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy,
+ struct platform_device *pdev)
+{
+ struct resource *res;
+ int err;
+ struct tegra_utmip_config *config;
+
+ tegra_phy->is_ulpi_phy = false;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!res) {
+ dev_err(&pdev->dev, "Failed to get UTMI Pad regs\n");
+ return -ENXIO;
+ }
+
+ tegra_phy->pad_regs = devm_ioremap(&pdev->dev, res->start,
+ resource_size(res));
+ if (!tegra_phy->regs) {
+ dev_err(&pdev->dev, "Failed to remap UTMI Pad regs\n");
+ return -ENOMEM;
+ }
+
+ tegra_phy->config = devm_kzalloc(&pdev->dev,
+ sizeof(*tegra_phy->config), GFP_KERNEL);
+ if (!tegra_phy->config) {
+ dev_err(&pdev->dev,
+ "unable to allocate memory for USB UTMIP config\n");
+ return -ENOMEM;
+ }
+
+ config = tegra_phy->config;
+
+ err = read_utmi_param(pdev, "nvidia,hssync-start-delay",
+ &config->hssync_start_delay);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,elastic-limit",
+ &config->elastic_limit);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,idle-wait-delay",
+ &config->idle_wait_delay);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,term-range-adj",
+ &config->term_range_adj);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,xcvr-setup",
+ &config->xcvr_setup);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,xcvr-lsfslew",
+ &config->xcvr_lsfslew);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,xcvr-lsrslew",
+ &config->xcvr_lsrslew);
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
static int tegra_usb_phy_probe(struct platform_device *pdev)
{
struct resource *res;
struct tegra_usb_phy *tegra_phy = NULL;
struct device_node *np = pdev->dev.of_node;
+ enum usb_phy_interface phy_type;
int err;
tegra_phy = devm_kzalloc(&pdev->dev, sizeof(*tegra_phy), GFP_KERNEL);
@@ -813,23 +886,15 @@
tegra_phy->is_legacy_phy =
of_property_read_bool(np, "nvidia,has-legacy-mode");
- err = of_property_match_string(np, "phy_type", "ulpi");
- if (err < 0) {
- tegra_phy->is_ulpi_phy = false;
+ phy_type = of_usb_get_phy_mode(np);
+ switch (phy_type) {
+ case USBPHY_INTERFACE_MODE_UTMI:
+ err = utmi_phy_probe(tegra_phy, pdev);
+ if (err < 0)
+ return err;
+ break;
- res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
- if (!res) {
- dev_err(&pdev->dev, "Failed to get UTMI Pad regs\n");
- return -ENXIO;
- }
-
- tegra_phy->pad_regs = devm_ioremap(&pdev->dev, res->start,
- resource_size(res));
- if (!tegra_phy->regs) {
- dev_err(&pdev->dev, "Failed to remap UTMI Pad regs\n");
- return -ENOMEM;
- }
- } else {
+ case USBPHY_INTERFACE_MODE_ULPI:
tegra_phy->is_ulpi_phy = true;
tegra_phy->reset_gpio =
@@ -839,19 +904,35 @@
tegra_phy->reset_gpio);
return tegra_phy->reset_gpio;
}
+ tegra_phy->config = NULL;
+ break;
+
+ default:
+ dev_err(&pdev->dev, "phy_type is invalid or unsupported\n");
+ return -EINVAL;
}
- err = of_property_match_string(np, "dr_mode", "otg");
- if (err < 0) {
- err = of_property_match_string(np, "dr_mode", "peripheral");
- if (err < 0)
- tegra_phy->mode = TEGRA_USB_PHY_MODE_HOST;
- else
- tegra_phy->mode = TEGRA_USB_PHY_MODE_DEVICE;
- } else
- tegra_phy->mode = TEGRA_USB_PHY_MODE_OTG;
+ if (of_find_property(np, "dr_mode", NULL))
+ tegra_phy->mode = of_usb_get_dr_mode(np);
+ else
+ tegra_phy->mode = USB_DR_MODE_HOST;
- tegra_phy->dev = &pdev->dev;
+ if (tegra_phy->mode == USB_DR_MODE_UNKNOWN) {
+ dev_err(&pdev->dev, "dr_mode is invalid\n");
+ return -EINVAL;
+ }
+
+ /* On some boards, the VBUS regulator doesn't need to be controlled */
+ if (of_find_property(np, "vbus-supply", NULL)) {
+ tegra_phy->vbus = devm_regulator_get(&pdev->dev, "vbus");
+ if (IS_ERR(tegra_phy->vbus))
+ return PTR_ERR(tegra_phy->vbus);
+ } else {
+ dev_notice(&pdev->dev, "no vbus regulator");
+ tegra_phy->vbus = ERR_PTR(-ENODEV);
+ }
+
+ tegra_phy->u_phy.dev = &pdev->dev;
err = tegra_usb_phy_init(tegra_phy);
if (err < 0)
return err;
@@ -860,6 +941,22 @@
tegra_phy->u_phy.set_suspend = tegra_usb_phy_suspend;
dev_set_drvdata(&pdev->dev, tegra_phy);
+
+ err = usb_add_phy_dev(&tegra_phy->u_phy);
+ if (err < 0) {
+ tegra_usb_phy_close(&tegra_phy->u_phy);
+ return err;
+ }
+
+ return 0;
+}
+
+static int tegra_usb_phy_remove(struct platform_device *pdev)
+{
+ struct tegra_usb_phy *tegra_phy = platform_get_drvdata(pdev);
+
+ usb_remove_phy(&tegra_phy->u_phy);
+
return 0;
}
@@ -871,6 +968,7 @@
static struct platform_driver tegra_usb_phy_driver = {
.probe = tegra_usb_phy_probe,
+ .remove = tegra_usb_phy_remove,
.driver = {
.name = "tegra-phy",
.owner = THIS_MODULE,
@@ -879,29 +977,5 @@
};
module_platform_driver(tegra_usb_phy_driver);
-static int tegra_usb_phy_match(struct device *dev, void *data)
-{
- struct tegra_usb_phy *tegra_phy = dev_get_drvdata(dev);
- struct device_node *dn = data;
-
- return (tegra_phy->dev->of_node == dn) ? 1 : 0;
-}
-
-struct usb_phy *tegra_usb_get_phy(struct device_node *dn)
-{
- struct device *dev;
- struct tegra_usb_phy *tegra_phy;
-
- dev = driver_find_device(&tegra_usb_phy_driver.driver, NULL, dn,
- tegra_usb_phy_match);
- if (!dev)
- return ERR_PTR(-EPROBE_DEFER);
-
- tegra_phy = dev_get_drvdata(dev);
-
- return &tegra_phy->u_phy;
-}
-EXPORT_SYMBOL_GPL(tegra_usb_get_phy);
-
MODULE_DESCRIPTION("Tegra USB PHY driver");
MODULE_LICENSE("GPL v2");
diff --git a/drivers/usb/phy/phy-twl4030-usb.c b/drivers/usb/phy/phy-twl4030-usb.c
index 8f78d2d..90730c8 100644
--- a/drivers/usb/phy/phy-twl4030-usb.c
+++ b/drivers/usb/phy/phy-twl4030-usb.c
@@ -648,7 +648,7 @@
static int twl4030_usb_probe(struct platform_device *pdev)
{
- struct twl4030_usb_data *pdata = pdev->dev.platform_data;
+ struct twl4030_usb_data *pdata = dev_get_platdata(&pdev->dev);
struct twl4030_usb *twl;
int status, err;
struct usb_otg *otg;
diff --git a/drivers/usb/phy/phy-twl6030-usb.c b/drivers/usb/phy/phy-twl6030-usb.c
index 1753bd3..16dbc93 100644
--- a/drivers/usb/phy/phy-twl6030-usb.c
+++ b/drivers/usb/phy/phy-twl6030-usb.c
@@ -324,7 +324,7 @@
int status, err;
struct device_node *np = pdev->dev.of_node;
struct device *dev = &pdev->dev;
- struct twl4030_usb_data *pdata = dev->platform_data;
+ struct twl4030_usb_data *pdata = dev_get_platdata(dev);
twl = devm_kzalloc(dev, sizeof *twl, GFP_KERNEL);
if (!twl)
diff --git a/drivers/usb/renesas_usbhs/common.c b/drivers/usb/renesas_usbhs/common.c
index cfd2050..3b39757 100644
--- a/drivers/usb/renesas_usbhs/common.c
+++ b/drivers/usb/renesas_usbhs/common.c
@@ -416,7 +416,7 @@
*/
static int usbhs_probe(struct platform_device *pdev)
{
- struct renesas_usbhs_platform_info *info = pdev->dev.platform_data;
+ struct renesas_usbhs_platform_info *info = dev_get_platdata(&pdev->dev);
struct renesas_usbhs_driver_callback *dfunc;
struct usbhs_priv *priv;
struct resource *res, *irq_res;
@@ -558,7 +558,7 @@
static int usbhs_remove(struct platform_device *pdev)
{
struct usbhs_priv *priv = usbhs_pdev_to_priv(pdev);
- struct renesas_usbhs_platform_info *info = pdev->dev.platform_data;
+ struct renesas_usbhs_platform_info *info = dev_get_platdata(&pdev->dev);
struct renesas_usbhs_driver_callback *dfunc = &info->driver_callback;
dev_dbg(&pdev->dev, "usb remove\n");
diff --git a/drivers/usb/renesas_usbhs/mod_gadget.c b/drivers/usb/renesas_usbhs/mod_gadget.c
index 805940c..3385aeb 100644
--- a/drivers/usb/renesas_usbhs/mod_gadget.c
+++ b/drivers/usb/renesas_usbhs/mod_gadget.c
@@ -77,9 +77,9 @@
struct usbhsg_gpriv, mod)
#define __usbhsg_for_each_uep(start, pos, g, i) \
- for (i = start, pos = (g)->uep + i; \
- i < (g)->uep_size; \
- i++, pos = (g)->uep + i)
+ for ((i) = start; \
+ ((i) < (g)->uep_size) && ((pos) = (g)->uep + (i)); \
+ (i)++)
#define usbhsg_for_each_uep(pos, gpriv, i) \
__usbhsg_for_each_uep(1, pos, gpriv, i)
diff --git a/drivers/usb/renesas_usbhs/mod_host.c b/drivers/usb/renesas_usbhs/mod_host.c
index b868154..e40f565 100644
--- a/drivers/usb/renesas_usbhs/mod_host.c
+++ b/drivers/usb/renesas_usbhs/mod_host.c
@@ -111,9 +111,9 @@
container_of(usbhs_mod_get(priv, USBHS_HOST), struct usbhsh_hpriv, mod)
#define __usbhsh_for_each_udev(start, pos, h, i) \
- for (i = start, pos = (h)->udev + i; \
- i < USBHSH_DEVICE_MAX; \
- i++, pos = (h)->udev + i)
+ for ((i) = start; \
+ ((i) < USBHSH_DEVICE_MAX) && ((pos) = (h)->udev + (i)); \
+ (i)++)
#define usbhsh_for_each_udev(pos, hpriv, i) \
__usbhsh_for_each_udev(1, pos, hpriv, i)
diff --git a/drivers/usb/renesas_usbhs/pipe.h b/drivers/usb/renesas_usbhs/pipe.h
index b476fde..3e53498 100644
--- a/drivers/usb/renesas_usbhs/pipe.h
+++ b/drivers/usb/renesas_usbhs/pipe.h
@@ -54,9 +54,9 @@
* pipe list
*/
#define __usbhs_for_each_pipe(start, pos, info, i) \
- for (i = start, pos = (info)->pipe + i; \
- i < (info)->size; \
- i++, pos = (info)->pipe + i)
+ for ((i) = start; \
+ ((i) < (info)->size) && ((pos) = (info)->pipe + (i)); \
+ (i)++)
#define usbhs_for_each_pipe(pos, priv, i) \
__usbhs_for_each_pipe(1, pos, &((priv)->pipe_info), i)
diff --git a/drivers/usb/usb-common.c b/drivers/usb/usb-common.c
index 675384d..d771870a 100644
--- a/drivers/usb/usb-common.c
+++ b/drivers/usb/usb-common.c
@@ -43,20 +43,20 @@
}
EXPORT_SYMBOL_GPL(usb_otg_state_string);
+static const char *const speed_names[] = {
+ [USB_SPEED_UNKNOWN] = "UNKNOWN",
+ [USB_SPEED_LOW] = "low-speed",
+ [USB_SPEED_FULL] = "full-speed",
+ [USB_SPEED_HIGH] = "high-speed",
+ [USB_SPEED_WIRELESS] = "wireless",
+ [USB_SPEED_SUPER] = "super-speed",
+};
+
const char *usb_speed_string(enum usb_device_speed speed)
{
- static const char *const names[] = {
- [USB_SPEED_UNKNOWN] = "UNKNOWN",
- [USB_SPEED_LOW] = "low-speed",
- [USB_SPEED_FULL] = "full-speed",
- [USB_SPEED_HIGH] = "high-speed",
- [USB_SPEED_WIRELESS] = "wireless",
- [USB_SPEED_SUPER] = "super-speed",
- };
-
- if (speed < 0 || speed >= ARRAY_SIZE(names))
+ if (speed < 0 || speed >= ARRAY_SIZE(speed_names))
speed = USB_SPEED_UNKNOWN;
- return names[speed];
+ return speed_names[speed];
}
EXPORT_SYMBOL_GPL(usb_speed_string);
@@ -112,6 +112,33 @@
return USB_DR_MODE_UNKNOWN;
}
EXPORT_SYMBOL_GPL(of_usb_get_dr_mode);
+
+/**
+ * of_usb_get_maximum_speed - Get maximum requested speed for a given USB
+ * controller.
+ * @np: Pointer to the given device_node
+ *
+ * The function gets the maximum speed string from property "maximum-speed",
+ * and returns the corresponding enum usb_device_speed.
+ */
+enum usb_device_speed of_usb_get_maximum_speed(struct device_node *np)
+{
+ const char *maximum_speed;
+ int err;
+ int i;
+
+ err = of_property_read_string(np, "maximum-speed", &maximum_speed);
+ if (err < 0)
+ return USB_SPEED_UNKNOWN;
+
+ for (i = 0; i < ARRAY_SIZE(speed_names); i++)
+ if (strcmp(maximum_speed, speed_names[i]) == 0)
+ return i;
+
+ return USB_SPEED_UNKNOWN;
+}
+EXPORT_SYMBOL_GPL(of_usb_get_maximum_speed);
+
#endif
MODULE_LICENSE("GPL");
diff --git a/include/linux/platform_data/tegra_usb.h b/include/linux/platform_data/tegra_usb.h
deleted file mode 100644
index 66c673f..0000000
--- a/include/linux/platform_data/tegra_usb.h
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * Copyright (C) 2010 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef _TEGRA_USB_H_
-#define _TEGRA_USB_H_
-
-enum tegra_usb_operating_modes {
- TEGRA_USB_DEVICE,
- TEGRA_USB_HOST,
- TEGRA_USB_OTG,
-};
-
-struct tegra_ehci_platform_data {
- enum tegra_usb_operating_modes operating_mode;
- /* power down the phy on bus suspend */
- int power_down_on_bus_suspend;
- void *phy_config;
- int vbus_gpio;
-};
-
-#endif /* _TEGRA_USB_H_ */
diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h
index f1b0dca..942ef5e 100644
--- a/include/linux/usb/gadget.h
+++ b/include/linux/usb/gadget.h
@@ -22,6 +22,7 @@
#include <linux/slab.h>
#include <linux/scatterlist.h>
#include <linux/types.h>
+#include <linux/workqueue.h>
#include <linux/usb/ch9.h>
struct usb_ep;
@@ -475,6 +476,7 @@
/**
* struct usb_gadget - represents a usb slave device
+ * @work: (internal use) Workqueue to be used for sysfs_notify()
* @ops: Function pointers used to access hardware-specific operations.
* @ep0: Endpoint zero, used when reading or writing responses to
* driver setup() requests
@@ -520,6 +522,7 @@
* device is acting as a B-Peripheral (so is_a_peripheral is false).
*/
struct usb_gadget {
+ struct work_struct work;
/* readonly to gadget driver */
const struct usb_gadget_ops *ops;
struct usb_ep *ep0;
@@ -538,6 +541,7 @@
unsigned out_epnum;
unsigned in_epnum;
};
+#define work_to_gadget(w) (container_of((w), struct usb_gadget, work))
static inline void set_gadget_data(struct usb_gadget *gadget, void *data)
{ dev_set_drvdata(&gadget->dev, data); }
diff --git a/include/linux/usb/of.h b/include/linux/usb/of.h
index a0ef405..8c38aa2 100644
--- a/include/linux/usb/of.h
+++ b/include/linux/usb/of.h
@@ -7,19 +7,27 @@
#ifndef __LINUX_USB_OF_H
#define __LINUX_USB_OF_H
+#include <linux/usb/ch9.h>
#include <linux/usb/otg.h>
#include <linux/usb/phy.h>
#if IS_ENABLED(CONFIG_OF)
enum usb_dr_mode of_usb_get_dr_mode(struct device_node *np);
+enum usb_device_speed of_usb_get_maximum_speed(struct device_node *np);
#else
static inline enum usb_dr_mode of_usb_get_dr_mode(struct device_node *np)
{
return USB_DR_MODE_UNKNOWN;
}
+
+static inline enum usb_device_speed
+of_usb_get_maximum_speed(struct device_node *np)
+{
+ return USB_SPEED_UNKNOWN;
+}
#endif
-#if IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_USB_PHY)
+#if IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_USB_SUPPORT)
enum usb_phy_interface of_usb_get_phy_mode(struct device_node *np);
#else
static inline enum usb_phy_interface of_usb_get_phy_mode(struct device_node *np)
diff --git a/include/linux/usb/phy.h b/include/linux/usb/phy.h
index 4403680..6c0b1c5 100644
--- a/include/linux/usb/phy.h
+++ b/include/linux/usb/phy.h
@@ -142,7 +142,7 @@
/* helpers for direct access thru low-level io interface */
static inline int usb_phy_io_read(struct usb_phy *x, u32 reg)
{
- if (x->io_ops && x->io_ops->read)
+ if (x && x->io_ops && x->io_ops->read)
return x->io_ops->read(x, reg);
return -EINVAL;
@@ -150,7 +150,7 @@
static inline int usb_phy_io_write(struct usb_phy *x, u32 val, u32 reg)
{
- if (x->io_ops && x->io_ops->write)
+ if (x && x->io_ops && x->io_ops->write)
return x->io_ops->write(x, val, reg);
return -EINVAL;
@@ -159,7 +159,7 @@
static inline int
usb_phy_init(struct usb_phy *x)
{
- if (x->init)
+ if (x && x->init)
return x->init(x);
return 0;
@@ -168,14 +168,14 @@
static inline void
usb_phy_shutdown(struct usb_phy *x)
{
- if (x->shutdown)
+ if (x && x->shutdown)
x->shutdown(x);
}
static inline int
usb_phy_vbus_on(struct usb_phy *x)
{
- if (!x->set_vbus)
+ if (!x || !x->set_vbus)
return 0;
return x->set_vbus(x, true);
@@ -184,7 +184,7 @@
static inline int
usb_phy_vbus_off(struct usb_phy *x)
{
- if (!x->set_vbus)
+ if (!x || !x->set_vbus)
return 0;
return x->set_vbus(x, false);
@@ -258,7 +258,7 @@
static inline int
usb_phy_set_suspend(struct usb_phy *x, int suspend)
{
- if (x->set_suspend != NULL)
+ if (x && x->set_suspend != NULL)
return x->set_suspend(x, suspend);
else
return 0;
@@ -267,7 +267,7 @@
static inline int
usb_phy_notify_connect(struct usb_phy *x, enum usb_device_speed speed)
{
- if (x->notify_connect)
+ if (x && x->notify_connect)
return x->notify_connect(x, speed);
else
return 0;
@@ -276,7 +276,7 @@
static inline int
usb_phy_notify_disconnect(struct usb_phy *x, enum usb_device_speed speed)
{
- if (x->notify_disconnect)
+ if (x && x->notify_disconnect)
return x->notify_disconnect(x, speed);
else
return 0;
diff --git a/include/linux/usb/tegra_usb_phy.h b/include/linux/usb/tegra_usb_phy.h
index d2ca919..d3db274 100644
--- a/include/linux/usb/tegra_usb_phy.h
+++ b/include/linux/usb/tegra_usb_phy.h
@@ -28,23 +28,12 @@
u8 xcvr_lsrslew;
};
-struct tegra_ulpi_config {
- int reset_gpio;
- const char *clk;
-};
-
enum tegra_usb_phy_port_speed {
TEGRA_USB_PHY_PORT_SPEED_FULL = 0,
TEGRA_USB_PHY_PORT_SPEED_LOW,
TEGRA_USB_PHY_PORT_SPEED_HIGH,
};
-enum tegra_usb_phy_mode {
- TEGRA_USB_PHY_MODE_DEVICE,
- TEGRA_USB_PHY_MODE_HOST,
- TEGRA_USB_PHY_MODE_OTG,
-};
-
struct tegra_xtal_freq;
struct tegra_usb_phy {
@@ -55,18 +44,16 @@
struct clk *clk;
struct clk *pll_u;
struct clk *pad_clk;
- enum tegra_usb_phy_mode mode;
+ struct regulator *vbus;
+ enum usb_dr_mode mode;
void *config;
struct usb_phy *ulpi;
struct usb_phy u_phy;
- struct device *dev;
bool is_legacy_phy;
bool is_ulpi_phy;
int reset_gpio;
};
-struct usb_phy *tegra_usb_get_phy(struct device_node *dn);
-
void tegra_usb_phy_preresume(struct usb_phy *phy);
void tegra_usb_phy_postresume(struct usb_phy *phy);
