// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Device Tree file for Freescale LS2080A RDB Board.
 *
 * Copyright 2016 Freescale Semiconductor, Inc.
 * Copyright 2017-2020 NXP
 *
 * Abhimanyu Saini <abhimanyu.saini@nxp.com>
 *
 */

&esdhc {
	status = "okay";
};

&ifc {
	status = "okay";
	#address-cells = <2>;
	#size-cells = <1>;
	ranges = <0x0 0x0 0x5 0x80000000 0x08000000
		  0x2 0x0 0x5 0x30000000 0x00010000
		  0x3 0x0 0x5 0x20000000 0x00010000>;

	nor@0,0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "cfi-flash";
		reg = <0x0 0x0 0x8000000>;
		bank-width = <2>;
		device-width = <1>;
	};

	nand@2,0 {
	     compatible = "fsl,ifc-nand";
	     reg = <0x2 0x0 0x10000>;
	};

	cpld@3,0 {
	     reg = <0x3 0x0 0x10000>;
	     compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis";
	};

};

&i2c0 {
	status = "okay";
	pca9547@75 {
		compatible = "nxp,pca9547";
		reg = <0x75>;
		#address-cells = <1>;
		#size-cells = <0>;
		i2c@1 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x01>;
			rtc@68 {
				compatible = "dallas,ds3232";
				reg = <0x68>;
				/* IRQ_RTC_B -> IRQ06, active low */
				interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
			};
		};

		i2c@2 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x02>;

			ina220@40 {
				compatible = "ti,ina220";
				reg = <0x40>;
				shunt-resistor = <500>;
			};
		};

		i2c@3 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x3>;

			adt7481@4c {
				compatible = "adi,adt7461";
				reg = <0x4c>;
			};
		};
	};
};

&i2c1 {
	status = "disabled";
};

&i2c2 {
	status = "disabled";
};

&i2c3 {
	status = "disabled";
};

&dspi {
	status = "okay";
	dflash0: n25q512a@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "st,m25p80";
		spi-max-frequency = <3000000>;
		reg = <0>;
	};
};

&qspi {
	status = "okay";

	s25fs512s0: flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "jedec,spi-nor";
		spi-max-frequency = <50000000>;
		reg = <0>;
	};
};

&sata0 {
	status = "okay";
};

&sata1 {
	status = "okay";
};

&usb0 {
	status = "okay";
};

&usb1 {
	status = "okay";
};