[media] saa7115: add config flag to change the IDQ polarity
Needed by the go7007 driver: it assumes a different polarity of the IDQ
signal, so we need to be able to tell the saa7115 about this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
diff --git a/drivers/media/i2c/saa7115.c b/drivers/media/i2c/saa7115.c
index 5d9d033..c3e7e12 100644
--- a/drivers/media/i2c/saa7115.c
+++ b/drivers/media/i2c/saa7115.c
@@ -1259,6 +1259,12 @@
(saa711x_read(sd, R_83_X_PORT_I_O_ENA_AND_OUT_CLK) & 0xfe) |
(state->output & 0x01));
}
+ if (state->ident > V4L2_IDENT_SAA7111A) {
+ if (config & SAA7115_IDQ_IS_DEFAULT)
+ saa711x_write(sd, R_85_I_PORT_SIGNAL_POLAR, 0x20);
+ else
+ saa711x_write(sd, R_85_I_PORT_SIGNAL_POLAR, 0x21);
+ }
return 0;
}
diff --git a/include/media/saa7115.h b/include/media/saa7115.h
index bab2127..8b2ecc6 100644
--- a/include/media/saa7115.h
+++ b/include/media/saa7115.h
@@ -21,6 +21,8 @@
#ifndef _SAA7115_H_
#define _SAA7115_H_
+/* s_routing inputs, outputs, and config */
+
/* SAA7111/3/4/5 HW inputs */
#define SAA7115_COMPOSITE0 0
#define SAA7115_COMPOSITE1 1
@@ -33,6 +35,25 @@
#define SAA7115_SVIDEO2 8
#define SAA7115_SVIDEO3 9
+/* outputs */
+#define SAA7115_IPORT_ON 1
+#define SAA7115_IPORT_OFF 0
+
+/* SAA7111 specific outputs. */
+#define SAA7111_VBI_BYPASS 2
+#define SAA7111_FMT_YUV422 0x00
+#define SAA7111_FMT_RGB 0x40
+#define SAA7111_FMT_CCIR 0x80
+#define SAA7111_FMT_YUV411 0xc0
+
+/* config flags */
+/* Register 0x85 should set bit 0 to 0 (it's 1 by default). This bit
+ * controls the IDQ signal polarity which is set to 'inverted' if the bit
+ * it 1 and to 'default' if it is 0. */
+#define SAA7115_IDQ_IS_DEFAULT (1 << 0)
+
+/* s_crystal_freq values and flags */
+
/* SAA7115 v4l2_crystal_freq frequency values */
#define SAA7115_FREQ_32_11_MHZ 32110000 /* 32.11 MHz crystal, SAA7114/5 only */
#define SAA7115_FREQ_24_576_MHZ 24576000 /* 24.576 MHz crystal */
@@ -42,15 +63,5 @@
#define SAA7115_FREQ_FL_CGCDIV (1 << 1) /* SA 3A[6], CGCDIV, SAA7115 only */
#define SAA7115_FREQ_FL_APLL (1 << 2) /* SA 3A[3], APLL, SAA7114/5 only */
-#define SAA7115_IPORT_ON 1
-#define SAA7115_IPORT_OFF 0
-
-/* SAA7111 specific output flags */
-#define SAA7111_VBI_BYPASS 2
-#define SAA7111_FMT_YUV422 0x00
-#define SAA7111_FMT_RGB 0x40
-#define SAA7111_FMT_CCIR 0x80
-#define SAA7111_FMT_YUV411 0xc0
-
#endif
