Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt

V3 Semiconductor V360 EPC PCI bridge

This bridge is found in the ARM Integrator/AP (Application Platform)

Required properties:
- compatible: should be one of:
  "v3,v360epc-pci"
  "arm,integrator-ap-pci", "v3,v360epc-pci"
- reg: should contain two register areas:
  first the base address of the V3 host bridge controller, 64KB
  second the configuration area register space, 16MB
- interrupts: should contain a reference to the V3 error interrupt
  as routed on the system.
- bus-range: see pci.txt
- ranges: this follows the standard PCI bindings in the IEEE Std
  1275-1994 (see pci.txt) with the following restriction:
  - The non-prefetchable and prefetchable memory windows must
    each be exactly 256MB (0x10000000) in size.
  - The prefetchable memory window must be immediately adjacent
    to the non-prefetcable memory window
- dma-ranges: three ranges for the inbound memory region. The ranges must
  be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB,
  64MB, 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked
  as pre-fetchable. Two ranges are supported by the hardware.

Integrator-specific required properties:
- syscon: should contain a link to the syscon device node, since
  on the Integrator, some registers in the syscon are required to
  operate the V3 host bridge.

Example:

pci: pciv3@62000000 {
	compatible = "arm,integrator-ap-pci", "v3,v360epc-pci";
	#interrupt-cells = <1>;
	#size-cells = <2>;
	#address-cells = <3>;
	reg = <0x62000000 0x10000>, <0x61000000 0x01000000>;
	interrupt-parent = <&pic>;
	interrupts = <17>; /* Bus error IRQ */
	clocks = <&pciclk>;
	bus-range = <0x00 0xff>;
	ranges = 0x01000000 0 0x00000000 /* I/O space @00000000 */
		0x60000000 0 0x01000000 /* 16 MiB @ LB 60000000 */
		0x02000000 0 0x40000000 /* non-prefectable memory @40000000 */
		0x40000000 0 0x10000000 /* 256 MiB @ LB 40000000 1:1 */
		0x42000000 0 0x50000000 /* prefetchable memory @50000000 */
		0x50000000 0 0x10000000>; /* 256 MiB @ LB 50000000 1:1 */
	dma-ranges = <0x02000000 0 0x20000000 /* EBI memory space */
		0x20000000 0 0x20000000 /* 512 MB @ LB 20000000 1:1 */
		0x02000000 0 0x80000000 /* Core module alias memory */
		0x80000000 0 0x40000000>; /* 1GB @ LB 80000000 */
	interrupt-map-mask = <0xf800 0 0 0x7>;
	interrupt-map = <
	/* IDSEL 9 */
	0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */
	0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */
	0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */
	0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */
	/* IDSEL 10 */
	0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */
	0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */
	0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */
	0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */
	/* IDSEL 11 */
	0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */
	0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */
	0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */
	0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */
	/* IDSEL 12 */
	0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */
	0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */
	0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */
	0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */
	>;
};