diff --git a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts
old mode 100755
new mode 100644
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index f0cbd86..d4b7c59 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -469,6 +469,7 @@
 			ti,hwmods = "rtc";
 			clocks = <&clk_32768_ck>;
 			clock-names = "int-clk";
+			system-power-controller;
 			status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts
index 9fb4772..ad2ae25 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/imx23-evk.dts
@@ -13,6 +13,43 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 29 0>;
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 18 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	apb@80000000 {
 		apbh@80000000 {
 			gpmi-nand@8000c000 {
@@ -52,31 +89,11 @@
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a>;
-				lcd-supply = <&reg_lcd_3v3>;
-				display = <&display0>;
 				status = "okay";
 
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9200000>;
-							hactive = <480>;
-							vactive = <272>;
-							hback-porch = <15>;
-							hfront-porch = <8>;
-							vback-porch = <12>;
-							vfront-porch = <4>;
-							hsync-len = <1>;
-							vsync-len = <1>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
+				port {
+					display_out: endpoint {
+						remote-endpoint = <&panel_in>;
 					};
 				};
 			};
@@ -118,32 +135,7 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_vddio_sd0: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 29 0>;
-		};
-
-		reg_lcd_3v3: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 18 0>;
-			enable-active-high;
-		};
-	};
-
-	backlight {
+	backlight_display: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 2 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 6b0ae66..93ab5bd 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -13,6 +13,87 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+
+	reg_fec_3v3: regulator-fec-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 15 0>;
+	};
+
+	reg_usb0_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 9 0>;
+		enable-active-high;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 8 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 30 0>;
+		enable-active-high;
+	};
+
+	reg_can_3v3: regulator-can-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 13 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	apb@80000000 {
 		apbh@80000000 {
 			gpmi-nand@8000c000 {
@@ -116,31 +197,11 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a
 					     &lcdif_pins_evk>;
-				lcd-supply = <&reg_lcd_3v3>;
-				display = <&display0>;
 				status = "okay";
 
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33500000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <89>;
-							hfront-porch = <164>;
-							vback-porch = <23>;
-							vfront-porch = <10>;
-							hsync-len = <10>;
-							vsync-len = <10>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
+				port {
+					display_out: endpoint {
+						remote-endpoint = <&panel_in>;
 					};
 				};
 			};
@@ -269,80 +330,6 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_vddio_sd0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 28 0>;
-		};
-
-		reg_fec_3v3: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "fec-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 15 0>;
-		};
-
-		reg_usb0_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 9 0>;
-			enable-active-high;
-		};
-
-		reg_usb1_vbus: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 8 0>;
-			enable-active-high;
-		};
-
-		reg_lcd_3v3: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 30 0>;
-			enable-active-high;
-		};
-
-		reg_can_3v3: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "can-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 13 0>;
-			enable-active-high;
-		};
-
-	};
-
 	sound {
 		compatible = "fsl,imx28-evk-sgtl5000",
 			     "fsl,mxs-audio-sgtl5000";
@@ -363,7 +350,7 @@
 		};
 	};
 
-	backlight {
+	backlight_display: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 2 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index 7cbc2ff..7234e83 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -126,10 +126,14 @@
 		interrupt-names = "msi";
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0x7>;
-		interrupt-map = <0 0 0 1 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 2 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 3 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 4 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		/*
+		 * Reference manual lists pci irqs incorrectly
+		 * Real hardware ordering is same as imx6: D+MSI, C, B, A
+		 */
+		interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
 			 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
 			 <&clks IMX7D_PCIE_PHY_ROOT_CLK>;
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
index 12d6822..04758a2 100644
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -354,7 +354,7 @@
 &mmc2 {
 	vmmc-supply = <&vsdio>;
 	bus-width = <8>;
-	non-removable;
+	ti,non-removable;
 };
 
 &mmc3 {
@@ -621,15 +621,6 @@
 		OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_fsx */
 		>;
 	};
-};
-
-&omap4_pmx_wkup {
-	usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
-		/* gpio_wk0 */
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
-		>;
-	};
 
 	vibrator_direction_pin: pinmux_vibrator_direction_pin {
 		pinctrl-single,pins = <
@@ -644,6 +635,15 @@
 	};
 };
 
+&omap4_pmx_wkup {
+	usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
+		/* gpio_wk0 */
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
+		>;
+	};
+};
+
 /*
  * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
  * uart1 wakeirq.
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index e2c1276..7eca43ff 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -257,6 +257,7 @@
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_LVDS=y
 CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_PANEL_SEIKO_43WVF1G=y
 CONFIG_DRM_DW_HDMI_AHB_AUDIO=m
 CONFIG_DRM_DW_HDMI_CEC=y
 CONFIG_DRM_IMX=y
diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
index 148226e..7b82128 100644
--- a/arch/arm/configs/mxs_defconfig
+++ b/arch/arm/configs/mxs_defconfig
@@ -95,6 +95,7 @@
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_DRM=y
+CONFIG_DRM_PANEL_SEIKO_43WVF1G=y
 CONFIG_DRM_MXSFB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
diff --git a/arch/arm/configs/versatile_defconfig b/arch/arm/configs/versatile_defconfig
index df68dc4..5282324 100644
--- a/arch/arm/configs/versatile_defconfig
+++ b/arch/arm/configs/versatile_defconfig
@@ -5,19 +5,19 @@
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_PARTITION_ADVANCED=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_VERSATILE=y
 CONFIG_AEABI=y
 CONFIG_OABI_COMPAT=y
-CONFIG_CMA=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="root=1f03 mem=32M"
 CONFIG_FPE_NWFPE=y
 CONFIG_VFP=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -59,6 +59,7 @@
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_ARM_VERSATILE=y
 CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_DUMB_VGA_DAC=y
 CONFIG_DRM_PL111=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
@@ -89,9 +90,10 @@
 CONFIG_NFSD_V3=y
 CONFIG_NLS_CODEPAGE_850=m
 CONFIG_NLS_ISO8859_1=m
+CONFIG_FONTS=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
-CONFIG_FONTS=y
-CONFIG_FONT_ACORN_8x8=y
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index 2ceffd8..cd65ea4 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -2161,6 +2161,37 @@ static int of_dev_hwmod_lookup(struct device_node *np,
 }
 
 /**
+ * omap_hwmod_fix_mpu_rt_idx - fix up mpu_rt_idx register offsets
+ *
+ * @oh: struct omap_hwmod *
+ * @np: struct device_node *
+ *
+ * Fix up module register offsets for modules with mpu_rt_idx.
+ * Only needed for cpsw with interconnect target module defined
+ * in device tree while still using legacy hwmod platform data
+ * for rev, sysc and syss registers.
+ *
+ * Can be removed when all cpsw hwmod platform data has been
+ * dropped.
+ */
+static void omap_hwmod_fix_mpu_rt_idx(struct omap_hwmod *oh,
+				      struct device_node *np,
+				      struct resource *res)
+{
+	struct device_node *child = NULL;
+	int error;
+
+	child = of_get_next_child(np, child);
+	if (!child)
+		return;
+
+	error = of_address_to_resource(child, oh->mpu_rt_idx, res);
+	if (error)
+		pr_err("%s: error mapping mpu_rt_idx: %i\n",
+		       __func__, error);
+}
+
+/**
  * omap_hwmod_parse_module_range - map module IO range from device tree
  * @oh: struct omap_hwmod *
  * @np: struct device_node *
@@ -2220,7 +2251,13 @@ int omap_hwmod_parse_module_range(struct omap_hwmod *oh,
 	size = be32_to_cpup(ranges);
 
 	pr_debug("omap_hwmod: %s %s at 0x%llx size 0x%llx\n",
-		 oh->name, np->name, base, size);
+		 oh ? oh->name : "", np->name, base, size);
+
+	if (oh && oh->mpu_rt_idx) {
+		omap_hwmod_fix_mpu_rt_idx(oh, np, res);
+
+		return 0;
+	}
 
 	res->start = base;
 	res->end = base + size - 1;
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index f67e8d5..db8d364 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -38,6 +38,7 @@
 CONFIG_ARCH_BERLIN=y
 CONFIG_ARCH_BRCMSTB=y
 CONFIG_ARCH_EXYNOS=y
+CONFIG_ARCH_K3=y
 CONFIG_ARCH_LAYERSCAPE=y
 CONFIG_ARCH_LG1K=y
 CONFIG_ARCH_HISI=y
@@ -605,6 +606,8 @@
 CONFIG_ARCH_TEGRA_210_SOC=y
 CONFIG_ARCH_TEGRA_186_SOC=y
 CONFIG_ARCH_TEGRA_194_SOC=y
+CONFIG_ARCH_K3_AM6_SOC=y
+CONFIG_SOC_TI=y
 CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
 CONFIG_EXTCON_USB_GPIO=y
 CONFIG_EXTCON_USBC_CROS_EC=y
diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c
index c9bac9d..e4fe954 100644
--- a/drivers/bus/ti-sysc.c
+++ b/drivers/bus/ti-sysc.c
@@ -498,32 +498,29 @@ static int sysc_check_registers(struct sysc *ddata)
 
 /**
  * syc_ioremap - ioremap register space for the interconnect target module
- * @ddata: deviec driver data
+ * @ddata: device driver data
  *
  * Note that the interconnect target module registers can be anywhere
- * within the first child device address space. For example, SGX has
- * them at offset 0x1fc00 in the 32MB module address space. We just
- * what we need around the interconnect target module registers.
+ * within the interconnect target module range. For example, SGX has
+ * them at offset 0x1fc00 in the 32MB module address space. And cpsw
+ * has them at offset 0x1200 in the CPSW_WR child. Usually the
+ * the interconnect target module registers are at the beginning of
+ * the module range though.
  */
 static int sysc_ioremap(struct sysc *ddata)
 {
-	u32 size = 0;
+	int size;
 
-	if (ddata->offsets[SYSC_SYSSTATUS] >= 0)
-		size = ddata->offsets[SYSC_SYSSTATUS];
-	else if (ddata->offsets[SYSC_SYSCONFIG] >= 0)
-		size = ddata->offsets[SYSC_SYSCONFIG];
-	else if (ddata->offsets[SYSC_REVISION] >= 0)
-		size = ddata->offsets[SYSC_REVISION];
-	else
+	size = max3(ddata->offsets[SYSC_REVISION],
+		    ddata->offsets[SYSC_SYSCONFIG],
+		    ddata->offsets[SYSC_SYSSTATUS]);
+
+	if (size < 0 || (size + sizeof(u32)) > ddata->module_size)
 		return -EINVAL;
 
-	size &= 0xfff00;
-	size += SZ_256;
-
 	ddata->module_va = devm_ioremap(ddata->dev,
 					ddata->module_pa,
-					size);
+					size + sizeof(u32));
 	if (!ddata->module_va)
 		return -EIO;
 
@@ -1224,10 +1221,10 @@ static int sysc_child_suspend_noirq(struct device *dev)
 	if (!pm_runtime_status_suspended(dev)) {
 		error = pm_generic_runtime_suspend(dev);
 		if (error) {
-			dev_err(dev, "%s error at %i: %i\n",
-				__func__, __LINE__, error);
+			dev_warn(dev, "%s busy at %i: %i\n",
+				 __func__, __LINE__, error);
 
-			return error;
+			return 0;
 		}
 
 		error = sysc_runtime_suspend(ddata->dev);