V4L/DVB (6199): cx23885: Changes to allow demodulators on each transport bus
cx23885: Changes to allow demodulators on each transport bus.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
diff --git a/drivers/media/video/cx23885/cx23885-cards.c b/drivers/media/video/cx23885/cx23885-cards.c
index cdda11d..b9012ac 100644
--- a/drivers/media/video/cx23885/cx23885-cards.c
+++ b/drivers/media/video/cx23885/cx23885-cards.c
@@ -111,7 +111,7 @@
},
[CX23885_BOARD_DVICO_FUSIONHDTV_5_EXP] = {
.name = "DViCO FusionHDTV5 Express",
- .portc = CX23885_MPEG_DVB,
+ .portb = CX23885_MPEG_DVB,
},
};
const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
@@ -197,8 +197,43 @@
dev->name, tv.model);
}
+void cx23885_gpio_setup(struct cx23885_dev *dev)
+{
+ switch(dev->board) {
+ case CX23885_BOARD_HAUPPAUGE_HVR1250:
+ /* GPIO-0 cx24227 demodulator reset */
+ cx_set(GP0_IO, 0x00010001); /* Bring the part out of reset */
+ break;
+ case CX23885_BOARD_HAUPPAUGE_HVR1800:
+ /* GPIO-0 656_CLK */
+ /* GPIO-1 656_D0 */
+ /* GPIO-2 8295A Reset */
+ /* GPIO-3-10 cx23417 data0-7 */
+ /* GPIO-11-14 cx23417 addr0-3 */
+ /* GPIO-15-18 cx23417 READY, CS, RD, WR */
+ /* GPIO-19 IR_RX */
+ // FIXME: Analog requires the tuner is brought out of reset
+ break;
+ }
+}
+
+int cx23885_ir_init(struct cx23885_dev *dev)
+{
+ switch (dev->board) {
+ case CX23885_BOARD_HAUPPAUGE_HVR1250:
+ case CX23885_BOARD_HAUPPAUGE_HVR1800:
+ /* FIXME: Implement me */
+ break;
+ }
+
+ return 0;
+}
+
void cx23885_card_setup(struct cx23885_dev *dev)
{
+ struct cx23885_tsport *ts1 = &dev->ts1;
+ struct cx23885_tsport *ts2 = &dev->ts2;
+
static u8 eeprom[256];
if (dev->i2c_bus[0].i2c_rc == 0) {
@@ -215,6 +250,22 @@
hauppauge_eeprom(dev, eeprom+0x80);
break;
}
+
+ switch (dev->board) {
+ case CX23885_BOARD_DVICO_FUSIONHDTV_5_EXP:
+ ts1->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
+ ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */
+ ts1->src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+ break;
+ case CX23885_BOARD_HAUPPAUGE_HVR1250:
+ case CX23885_BOARD_HAUPPAUGE_HVR1800:
+ case CX23885_BOARD_HAUPPAUGE_HVR1800lp:
+ default:
+ ts2->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
+ ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
+ ts2->src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+ }
+
}
/* ------------------------------------------------------------------ */
diff --git a/drivers/media/video/cx23885/cx23885-core.c b/drivers/media/video/cx23885/cx23885-core.c
index bcba192..5187996 100644
--- a/drivers/media/video/cx23885/cx23885-core.c
+++ b/drivers/media/video/cx23885/cx23885-core.c
@@ -604,24 +604,7 @@
cx23885_sram_channel_setup(dev, &dev->sram_channels[ SRAM_CH08 ], 128, 0);
cx23885_sram_channel_setup(dev, &dev->sram_channels[ SRAM_CH09 ], 128, 0);
- switch(dev->board) {
- case CX23885_BOARD_HAUPPAUGE_HVR1250:
- /* GPIO-0 cx24227 demodulator reset */
- dprintk( 1, "%s() Configuring HVR1250 GPIO's\n", __FUNCTION__);
- cx_set(GP0_IO, 0x00010001); /* Bring the part out of reset */
- break;
- case CX23885_BOARD_HAUPPAUGE_HVR1800:
- /* GPIO-0 656_CLK */
- /* GPIO-1 656_D0 */
- /* GPIO-2 8295A Reset */
- /* GPIO-3-10 cx23417 data0-7 */
- /* GPIO-11-14 cx23417 addr0-3 */
- /* GPIO-15-18 cx23417 READY, CS, RD, WR */
- /* GPIO-19 IR_RX */
- dprintk( 1, "%s() Configuring HVR1800 GPIO's\n", __FUNCTION__);
- // FIXME: Analog requires the tuner is brought out of reset
- break;
- }
+ cx23885_gpio_setup(dev);
}
@@ -656,17 +639,68 @@
int cx23885_risc_stopper(struct pci_dev *pci, struct btcx_riscmem *risc,
u32 reg, u32 mask, u32 value);
-static int cx23885_ir_init(struct cx23885_dev *dev)
+static int cx23885_init_tsport(struct cx23885_dev *dev, struct cx23885_tsport *port, int portno)
{
- dprintk(1, "%s()\n", __FUNCTION__);
+ dprintk(1, "%s(portno=%d)\n", __FUNCTION__, portno);
- switch (dev->board) {
- case CX23885_BOARD_HAUPPAUGE_HVR1250:
- case CX23885_BOARD_HAUPPAUGE_HVR1800:
- dprintk(1, "%s() FIXME - Implement IR support\n", __FUNCTION__);
+ /* Transport bus init dma queue - Common settings */
+ port->dma_ctl_val = 0x11; /* Enable RISC controller and Fifo */
+ port->ts_int_msk_val = 0x1111; /* TS port bits for RISC */
+
+ spin_lock_init(&port->slock);
+ port->dev = dev;
+ port->nr = portno;
+
+ INIT_LIST_HEAD(&port->mpegq.active);
+ INIT_LIST_HEAD(&port->mpegq.queued);
+ port->mpegq.timeout.function = cx23885_timeout;
+ port->mpegq.timeout.data = (unsigned long)port;
+ init_timer(&port->mpegq.timeout);
+
+ switch(portno) {
+ case 1:
+ port->reg_gpcnt = VID_B_GPCNT;
+ port->reg_gpcnt_ctl = VID_B_GPCNT_CTL;
+ port->reg_dma_ctl = VID_B_DMA_CTL;
+ port->reg_lngth = VID_B_LNGTH;
+ port->reg_hw_sop_ctrl = VID_B_HW_SOP_CTL;
+ port->reg_gen_ctrl = VID_B_GEN_CTL;
+ port->reg_bd_pkt_status = VID_B_BD_PKT_STATUS;
+ port->reg_sop_status = VID_B_SOP_STATUS;
+ port->reg_fifo_ovfl_stat = VID_B_FIFO_OVFL_STAT;
+ port->reg_vld_misc = VID_B_VLD_MISC;
+ port->reg_ts_clk_en = VID_B_TS_CLK_EN;
+ port->reg_src_sel = VID_B_SRC_SEL;
+ port->reg_ts_int_msk = VID_B_INT_MSK;
+ port->reg_ts_int_stat = VID_B_INT_STAT;
+ port->sram_chno = SRAM_CH03; /* VID_B */
+ port->pci_irqmask = 0x02; /* VID_B bit1 */
break;
+ case 2:
+ port->reg_gpcnt = VID_C_GPCNT;
+ port->reg_gpcnt_ctl = VID_C_GPCNT_CTL;
+ port->reg_dma_ctl = VID_C_DMA_CTL;
+ port->reg_lngth = VID_C_LNGTH;
+ port->reg_hw_sop_ctrl = VID_C_HW_SOP_CTL;
+ port->reg_gen_ctrl = VID_C_GEN_CTL;
+ port->reg_bd_pkt_status = VID_C_BD_PKT_STATUS;
+ port->reg_sop_status = VID_C_SOP_STATUS;
+ port->reg_fifo_ovfl_stat = VID_C_FIFO_OVFL_STAT;
+ port->reg_vld_misc = VID_C_VLD_MISC;
+ port->reg_ts_clk_en = VID_C_TS_CLK_EN;
+ port->reg_src_sel = 0;
+ port->reg_ts_int_msk = VID_C_INT_MSK;
+ port->reg_ts_int_stat = VID_C_INT_STAT;
+ port->sram_chno = SRAM_CH06; /* VID_C */
+ port->pci_irqmask = 0x04; /* VID_C bit2 */
+ break;
+ default:
+ BUG();
}
+ cx23885_risc_stopper(dev->pci, &port->mpegq.stopper,
+ port->reg_dma_ctl, port->dma_ctl_val, 0x00);
+
return 0;
}
@@ -746,16 +780,11 @@
dev->i2c_bus[2].reg_wdata = I2C3_WDATA;
dev->i2c_bus[2].i2c_period = (0x07 << 24); /* 1.95MHz */
- /* Transport bus init dma queue */
- spin_lock_init(&dev->ts2.slock);
- dev->ts2.dev = dev;
- dev->ts2.nr = 2;
+ if(cx23885_boards[dev->board].portb == CX23885_MPEG_DVB)
+ cx23885_init_tsport(dev, &dev->ts1, 1);
- INIT_LIST_HEAD(&dev->ts2.mpegq.active);
- INIT_LIST_HEAD(&dev->ts2.mpegq.queued);
- dev->ts2.mpegq.timeout.function = cx23885_timeout;
- dev->ts2.mpegq.timeout.data = (unsigned long)&dev->ts2;
- init_timer(&dev->ts2.mpegq.timeout);
+ if(cx23885_boards[dev->board].portc == CX23885_MPEG_DVB)
+ cx23885_init_tsport(dev, &dev->ts2, 2);
if (get_resources(dev) < 0) {
printk(KERN_ERR "CORE %s No more PCIe resources for "
@@ -788,71 +817,21 @@
cx23885_i2c_register(&dev->i2c_bus[1]);
cx23885_i2c_register(&dev->i2c_bus[2]);
cx23885_call_i2c_clients (&dev->i2c_bus[0], TUNER_SET_STANDBY, NULL);
-
cx23885_card_setup(dev);
cx23885_ir_init(dev);
- switch (dev->board) {
- case CX23885_BOARD_DVICO_FUSIONHDTV_5_EXP:
- dev->ts2.reg_gpcnt = VID_B_GPCNT;
- dev->ts2.reg_gpcnt_ctl = VID_B_GPCNT_CTL;
- dev->ts2.reg_dma_ctl = VID_B_DMA_CTL;
- dev->ts2.reg_lngth = VID_B_LNGTH;
- dev->ts2.reg_hw_sop_ctrl = VID_B_HW_SOP_CTL;
- dev->ts2.reg_gen_ctrl = VID_B_GEN_CTL;
- dev->ts2.reg_bd_pkt_status = VID_B_BD_PKT_STATUS;
- dev->ts2.reg_sop_status = VID_B_SOP_STATUS;
- dev->ts2.reg_fifo_ovfl_stat = VID_B_FIFO_OVFL_STAT;
- dev->ts2.reg_vld_misc = VID_B_VLD_MISC;
- dev->ts2.reg_ts_clk_en = VID_B_TS_CLK_EN;
- dev->ts2.reg_ts_int_msk = VID_B_INT_MSK;
- dev->ts2.reg_src_sel = VID_B_SRC_SEL;
-
- // FIXME: Make this board specific
- dev->ts2.pci_irqmask = 0x02; /* TS Port 2 bit */
- dev->ts2.dma_ctl_val = 0x11; /* Enable RISC controller and Fifo */
- dev->ts2.ts_int_msk_val = 0x1111; /* TS port bits for RISC */
- dev->ts2.gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
- dev->ts2.ts_clk_en_val = 0x1; /* Enable TS_CLK */
- dev->ts2.src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
-
- // Drive this from cards.c (portb/c) and move it outside of this switch
- dev->ts2.sram_chno = SRAM_CH03;
- break;
- default:
- dev->ts2.reg_gpcnt = VID_C_GPCNT;
- dev->ts2.reg_gpcnt_ctl = VID_C_GPCNT_CTL;
- dev->ts2.reg_dma_ctl = VID_C_DMA_CTL;
- dev->ts2.reg_lngth = VID_C_LNGTH;
- dev->ts2.reg_hw_sop_ctrl = VID_C_HW_SOP_CTL;
- dev->ts2.reg_gen_ctrl = VID_C_GEN_CTL;
- dev->ts2.reg_bd_pkt_status = VID_C_BD_PKT_STATUS;
- dev->ts2.reg_sop_status = VID_C_SOP_STATUS;
- dev->ts2.reg_fifo_ovfl_stat = VID_C_FIFO_OVFL_STAT;
- dev->ts2.reg_vld_misc = VID_C_VLD_MISC;
- dev->ts2.reg_ts_clk_en = VID_C_TS_CLK_EN;
- dev->ts2.reg_ts_int_msk = VID_C_INT_MSK;
- dev->ts2.reg_src_sel = 0;
-
- // FIXME: Make this board specific
- dev->ts2.pci_irqmask = 0x04; /* TS Port 2 bit */
- dev->ts2.dma_ctl_val = 0x11; /* Enable RISC controller and Fifo */
- dev->ts2.ts_int_msk_val = 0x1111; /* TS port bits for RISC */
- dev->ts2.gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
- dev->ts2.ts_clk_en_val = 0x1; /* Enable TS_CLK */
- dev->ts2.src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
-
- // Drive this from cards.c (portb/c) and move it outside of this switch
- dev->ts2.sram_chno = SRAM_CH06;
+ if(cx23885_boards[dev->board].portb == CX23885_MPEG_DVB) {
+ if (cx23885_dvb_register(&dev->ts1) < 0) {
+ printk(KERN_ERR "%s() Failed to register dvb adapters on VID_B\n",
+ __FUNCTION__);
+ }
}
- cx23885_risc_stopper(dev->pci, &dev->ts2.mpegq.stopper,
- dev->ts2.reg_dma_ctl, dev->ts2.dma_ctl_val, 0x00);
-
- // FIXME: This should only be called if ts2 is being used, driven by cards.c
- if (cx23885_dvb_register(&dev->ts2) < 0) {
- printk(KERN_ERR "%s() Failed to register dvb adapters\n",
- __FUNCTION__);
+ if(cx23885_boards[dev->board].portc == CX23885_MPEG_DVB) {
+ if (cx23885_dvb_register(&dev->ts2) < 0) {
+ printk(KERN_ERR "%s() Failed to register dvb adapters on VID_C\n",
+ __FUNCTION__);
+ }
}
return 0;
@@ -870,7 +849,12 @@
if (!atomic_dec_and_test(&dev->refcount))
return;
- cx23885_dvb_unregister(&dev->ts2);
+ if(cx23885_boards[dev->board].portb == CX23885_MPEG_DVB)
+ cx23885_dvb_unregister(&dev->ts1);
+
+ if(cx23885_boards[dev->board].portc == CX23885_MPEG_DVB)
+ cx23885_dvb_unregister(&dev->ts2);
+
cx23885_i2c_unregister(&dev->i2c_bus[2]);
cx23885_i2c_unregister(&dev->i2c_bus[1]);
cx23885_i2c_unregister(&dev->i2c_bus[0]);
@@ -1289,14 +1273,66 @@
do_cancel_buffers(port, "timeout", 1);
}
+static int cx23885_irq_ts(struct cx23885_tsport *port, u32 status)
+{
+ struct cx23885_dev *dev = port->dev;
+ int handled = 0;
+ u32 count;
+
+ if ( (status & VID_BC_MSK_OPC_ERR) ||
+ (status & VID_BC_MSK_BAD_PKT) ||
+ (status & VID_BC_MSK_SYNC) ||
+ (status & VID_BC_MSK_OF))
+ {
+ if (status & VID_BC_MSK_OPC_ERR)
+ dprintk(7, " (VID_BC_MSK_OPC_ERR 0x%08x)\n", VID_BC_MSK_OPC_ERR);
+ if (status & VID_BC_MSK_BAD_PKT)
+ dprintk(7, " (VID_BC_MSK_BAD_PKT 0x%08x)\n", VID_BC_MSK_BAD_PKT);
+ if (status & VID_BC_MSK_SYNC)
+ dprintk(7, " (VID_BC_MSK_SYNC 0x%08x)\n", VID_BC_MSK_SYNC);
+ if (status & VID_BC_MSK_OF)
+ dprintk(7, " (VID_BC_MSK_OF 0x%08x)\n", VID_BC_MSK_OF);
+
+ printk(KERN_ERR "%s: mpeg risc op code error\n", dev->name);
+
+ cx_clear(port->reg_dma_ctl, port->dma_ctl_val);
+ cx23885_sram_channel_dump(dev, &dev->sram_channels[ port->sram_chno ]);
+
+ } else if (status & VID_BC_MSK_RISCI1) {
+
+ dprintk(7, " (RISCI1 0x%08x)\n", VID_BC_MSK_RISCI1);
+
+ spin_lock(&port->slock);
+ count = cx_read(port->reg_gpcnt);
+ cx23885_wakeup(port, &port->mpegq, count);
+ spin_unlock(&port->slock);
+
+ } else if (status & VID_BC_MSK_RISCI2) {
+
+ dprintk(7, " (RISCI2 0x%08x)\n", VID_BC_MSK_RISCI2);
+
+ spin_lock(&port->slock);
+ cx23885_restart_queue(port, &port->mpegq);
+ spin_unlock(&port->slock);
+
+ }
+ if (status) {
+ cx_write(port->reg_ts_int_stat, status);
+ handled = 1;
+ }
+
+ return handled;
+}
+
static irqreturn_t cx23885_irq(int irq, void *dev_id)
{
struct cx23885_dev *dev = dev_id;
- struct cx23885_tsport *port = &dev->ts2;
+ struct cx23885_tsport *ts1 = &dev->ts1;
+ struct cx23885_tsport *ts2 = &dev->ts2;
u32 pci_status, pci_mask;
u32 ts1_status, ts1_mask;
u32 ts2_status, ts2_mask;
- int count = 0, handled = 0;
+ int ts1_count = 0, ts2_count = 0, handled = 0;
pci_status = cx_read(PCI_INT_STAT);
pci_mask = cx_read(PCI_INT_MSK);
@@ -1308,10 +1344,11 @@
if ( (pci_status == 0) && (ts2_status == 0) && (ts1_status == 0) )
goto out;
- count = cx_read(port->reg_gpcnt);
+ ts1_count = cx_read(ts1->reg_gpcnt);
+ ts2_count = cx_read(ts2->reg_gpcnt);
dprintk(7, "pci_status: 0x%08x pci_mask: 0x%08x\n", pci_status, pci_mask );
- dprintk(7, "ts1_status: 0x%08x ts1_mask: 0x%08x count: 0x%x\n", ts1_status, ts1_mask, count );
- dprintk(7, "ts2_status: 0x%08x ts2_mask: 0x%08x count: 0x%x\n", ts2_status, ts2_mask, count );
+ dprintk(7, "ts1_status: 0x%08x ts1_mask: 0x%08x count: 0x%x\n", ts1_status, ts1_mask, ts1_count );
+ dprintk(7, "ts2_status: 0x%08x ts2_mask: 0x%08x count: 0x%x\n", ts2_status, ts2_mask, ts2_count );
if ( (pci_status & PCI_MSK_RISC_RD) ||
(pci_status & PCI_MSK_RISC_WR) ||
@@ -1348,90 +1385,11 @@
}
- if ( (ts1_status & VID_B_MSK_OPC_ERR) ||
- (ts1_status & VID_B_MSK_BAD_PKT) ||
- (ts1_status & VID_B_MSK_SYNC) ||
- (ts1_status & VID_B_MSK_OF))
- {
- if (ts1_status & VID_B_MSK_OPC_ERR)
- dprintk(7, " (VID_B_MSK_OPC_ERR 0x%08x)\n", VID_B_MSK_OPC_ERR);
- if (ts1_status & VID_B_MSK_BAD_PKT)
- dprintk(7, " (VID_B_MSK_BAD_PKT 0x%08x)\n", VID_B_MSK_BAD_PKT);
- if (ts1_status & VID_B_MSK_SYNC)
- dprintk(7, " (VID_B_MSK_SYNC 0x%08x)\n", VID_B_MSK_SYNC);
- if (ts1_status & VID_B_MSK_OF)
- dprintk(7, " (VID_B_MSK_OF 0x%08x)\n", VID_B_MSK_OF);
+ if (ts1_status)
+ handled += cx23885_irq_ts(ts1, ts1_status);
- printk(KERN_ERR "%s: mpeg risc op code error\n", dev->name);
-
- cx_clear(port->reg_dma_ctl, port->dma_ctl_val);
- cx23885_sram_channel_dump(dev, &dev->sram_channels[ port->sram_chno ]);
-
- } else if (ts1_status & VID_B_MSK_RISCI1) {
-
- dprintk(7, " (RISCI1 0x%08x)\n", VID_B_MSK_RISCI1);
-
- spin_lock(&port->slock);
- count = cx_read(port->reg_gpcnt);
- cx23885_wakeup(port, &port->mpegq, count);
- spin_unlock(&port->slock);
-
- } else if (ts1_status & VID_B_MSK_RISCI2) {
-
- dprintk(7, " (RISCI2 0x%08x)\n", VID_B_MSK_RISCI2);
-
- spin_lock(&port->slock);
- cx23885_restart_queue(port, &port->mpegq);
- spin_unlock(&port->slock);
-
- }
- if (ts1_status) {
- cx_write(VID_B_INT_STAT, ts1_status);
- handled = 1;
- }
-
- if ( (ts2_status & VID_C_MSK_OPC_ERR) ||
- (ts2_status & VID_C_MSK_BAD_PKT) ||
- (ts2_status & VID_C_MSK_SYNC) ||
- (ts2_status & VID_C_MSK_OF))
- {
- if (ts2_status & VID_C_MSK_OPC_ERR)
- dprintk(7, " (VID_C_MSK_OPC_ERR 0x%08x)\n", VID_C_MSK_OPC_ERR);
- if (ts2_status & VID_C_MSK_BAD_PKT)
- dprintk(7, " (VID_C_MSK_BAD_PKT 0x%08x)\n", VID_C_MSK_BAD_PKT);
- if (ts2_status & VID_C_MSK_SYNC)
- dprintk(7, " (VID_C_MSK_SYNC 0x%08x)\n", VID_C_MSK_SYNC);
- if (ts2_status & VID_C_MSK_OF)
- dprintk(7, " (VID_C_MSK_OF 0x%08x)\n", VID_C_MSK_OF);
-
- printk(KERN_ERR "%s: mpeg risc op code error\n", dev->name);
-
- cx_clear(port->reg_dma_ctl, port->dma_ctl_val);
- cx23885_sram_channel_dump(dev, &dev->sram_channels[ port->sram_chno ]);
-
- } else if (ts2_status & VID_C_MSK_RISCI1) {
-
- dprintk(7, " (RISCI1 0x%08x)\n", VID_C_MSK_RISCI1);
-
- spin_lock(&port->slock);
- count = cx_read(port->reg_gpcnt);
- cx23885_wakeup(port, &port->mpegq, count);
- spin_unlock(&port->slock);
-
- } else if (ts2_status & VID_C_MSK_RISCI2) {
-
- dprintk(7, " (RISCI2 0x%08x)\n", VID_C_MSK_RISCI2);
-
- spin_lock(&port->slock);
- cx23885_restart_queue(port, &port->mpegq);
- spin_unlock(&port->slock);
-
- }
-
- if (ts2_status) {
- cx_write(VID_C_INT_STAT, ts2_status);
- handled = 1;
- }
+ if (ts2_status)
+ handled += cx23885_irq_ts(ts2, ts2_status);
if (handled)
cx_write(PCI_INT_STAT, pci_status);
diff --git a/drivers/media/video/cx23885/cx23885-dvb.c b/drivers/media/video/cx23885/cx23885-dvb.c
index 0ace919..e0dc149 100644
--- a/drivers/media/video/cx23885/cx23885-dvb.c
+++ b/drivers/media/video/cx23885/cx23885-dvb.c
@@ -160,6 +160,7 @@
}
/* Put the analog decoder in standby to keep it quiet */
+ /* Assumption here: analog decoder is only on i2c bus 0 */
cx23885_call_i2c_clients (&dev->i2c_bus[0], TUNER_SET_STANDBY, NULL);
/* register everything */
@@ -180,8 +181,6 @@
dev->pci_slot);
err = -ENODEV;
- if (!(cx23885_boards[dev->board].portc & CX23885_MPEG_DVB))
- goto fail_core;
/* dvb stuff */
printk("%s: cx23885 based dvb card\n", dev->name);
@@ -192,7 +191,6 @@
if (err != 0)
printk("%s() dvb_register failed err = %d\n", __FUNCTION__, err);
- fail_core:
return err;
}
diff --git a/drivers/media/video/cx23885/cx23885-reg.h b/drivers/media/video/cx23885/cx23885-reg.h
index 3f1afbe..162169f 100644
--- a/drivers/media/video/cx23885/cx23885-reg.h
+++ b/drivers/media/video/cx23885/cx23885-reg.h
@@ -250,14 +250,16 @@
#define VID_C_MSK_OF (1 << 8)
#define VID_C_MSK_RISCI2 (1 << 4)
#define VID_C_MSK_RISCI1 1
-#define VID_C_INT_MSK 0x00040040
-#define VID_C_MSK_BAD_PKT (1 << 20)
-#define VID_C_MSK_OPC_ERR (1 << 16)
-#define VID_C_MSK_SYNC (1 << 12)
-#define VID_C_MSK_OF (1 << 8)
-#define VID_C_MSK_RISCI2 (1 << 4)
-#define VID_C_MSK_RISCI1 1
+/* A superset for testing purposes */
+#define VID_BC_MSK_BAD_PKT (1 << 20)
+#define VID_BC_MSK_OPC_ERR (1 << 16)
+#define VID_BC_MSK_SYNC (1 << 12)
+#define VID_BC_MSK_OF (1 << 8)
+#define VID_BC_MSK_RISCI2 (1 << 4)
+#define VID_BC_MSK_RISCI1 1
+
+#define VID_C_INT_MSK 0x00040040
#define VID_C_INT_STAT 0x00040044
#define VID_C_INT_MSTAT 0x00040048
#define VID_C_INT_SSTAT 0x0004004C
diff --git a/drivers/media/video/cx23885/cx23885.h b/drivers/media/video/cx23885/cx23885.h
index 4933274..45c47cd 100644
--- a/drivers/media/video/cx23885/cx23885.h
+++ b/drivers/media/video/cx23885/cx23885.h
@@ -168,6 +168,7 @@
u32 reg_vld_misc;
u32 reg_ts_clk_en;
u32 reg_ts_int_msk;
+ u32 reg_ts_int_stat;
u32 reg_src_sel;
/* Default register vals */
@@ -201,7 +202,7 @@
unsigned int board;
char name[32];
- struct cx23885_tsport ts2;
+ struct cx23885_tsport ts1, ts2;
/* sram configuration */
struct sram_channel *sram_channels;
@@ -269,6 +270,8 @@
extern const unsigned int cx23885_idcount;
extern void cx23885_card_list(struct cx23885_dev *dev);
+extern int cx23885_ir_init(struct cx23885_dev *dev);
+extern void cx23885_gpio_setup(struct cx23885_dev *dev);
extern void cx23885_card_setup(struct cx23885_dev *dev);
extern void cx23885_card_setup_pre_i2c(struct cx23885_dev *dev);
