| // SPDX-License-Identifier: GPL-2.0 |
| #include "qcom-msm8974pro.dtsi" |
| #include "pma8084.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include <dt-bindings/leds/common.h> |
| |
| / { |
| chassis-type = "handset"; |
| |
| aliases { |
| serial0 = &blsp1_uart1; |
| mmc0 = &sdhc_1; /* SDC1 eMMC slot */ |
| mmc1 = &sdhc_3; /* SDC2 SD card slot */ |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_pin_a>; |
| |
| key-volume-down { |
| label = "volume_down"; |
| gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| debounce-interval = <15>; |
| }; |
| |
| key-home { |
| label = "home_key"; |
| gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_HOMEPAGE>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| |
| key-volume-up { |
| label = "volume_up"; |
| gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEUP>; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| i2c-gpio-touchkey { |
| compatible = "i2c-gpio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c_touchkey_pins>; |
| |
| touchkey@20 { |
| compatible = "cypress,tm2-touchkey"; |
| reg = <0x20>; |
| |
| interrupt-parent = <&pma8084_gpios>; |
| interrupts = <6 IRQ_TYPE_EDGE_FALLING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touchkey_pin>; |
| |
| vcc-supply = <&max77826_ldo15>; |
| vdd-supply = <&pma8084_l19>; |
| |
| linux,keycodes = <KEY_APPSELECT KEY_BACK>; |
| }; |
| }; |
| |
| i2c_led_gpio: i2c-gpio-led { |
| compatible = "i2c-gpio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c_led_gpioex_pins>; |
| |
| i2c-gpio,delay-us = <2>; |
| |
| gpio_expander: gpio@20 { |
| compatible = "nxp,pcal6416"; |
| reg = <0x20>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| vcc-supply = <&pma8084_s4>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpioex_pin>; |
| |
| reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>; |
| }; |
| |
| led-controller@30 { |
| compatible = "panasonic,an30259a"; |
| reg = <0x30>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@1 { |
| reg = <1>; |
| function = LED_FUNCTION_STATUS; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| function = LED_FUNCTION_STATUS; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@3 { |
| reg = <3>; |
| function = LED_FUNCTION_STATUS; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| vreg_wlan: wlan-regulator { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "wl-reg"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vreg_panel: panel-regulator { |
| compatible = "regulator-fixed"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&panel_en_pin>; |
| |
| regulator-name = "panel-vddr-reg"; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <1500000>; |
| |
| gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vreg_vph_pwr: vreg-vph-pwr { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph-pwr"; |
| |
| regulator-min-microvolt = <3600000>; |
| regulator-max-microvolt = <3600000>; |
| |
| regulator-always-on; |
| }; |
| }; |
| |
| &blsp1_i2c2 { |
| status = "okay"; |
| |
| touchscreen@20 { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x20>; |
| |
| interrupt-parent = <&pma8084_gpios>; |
| interrupts = <8 IRQ_TYPE_EDGE_FALLING>; |
| |
| vdd-supply = <&max77826_ldo13>; |
| vio-supply = <&pma8084_lvs2>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touch_pin>; |
| |
| syna,startup-delay-ms = <100>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| rmi4-f01@1 { |
| reg = <0x1>; |
| syna,nosleep-mode = <1>; |
| }; |
| |
| rmi4-f12@12 { |
| reg = <0x12>; |
| syna,sensor-type = <1>; |
| }; |
| }; |
| }; |
| |
| &blsp1_i2c6 { |
| status = "okay"; |
| |
| pmic@60 { |
| reg = <0x60>; |
| compatible = "maxim,max77826"; |
| |
| regulators { |
| max77826_ldo1: LDO1 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| max77826_ldo2: LDO2 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| }; |
| |
| max77826_ldo3: LDO3 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| max77826_ldo4: LDO4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| max77826_ldo5: LDO5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| max77826_ldo6: LDO6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| max77826_ldo7: LDO7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| max77826_ldo8: LDO8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| max77826_ldo9: LDO9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| max77826_ldo10: LDO10 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| max77826_ldo11: LDO11 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| max77826_ldo12: LDO12 { |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| max77826_ldo13: LDO13 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| max77826_ldo14: LDO14 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| max77826_ldo15: LDO15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| max77826_buck: BUCK { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| max77826_buckboost: BUCKBOOST { |
| regulator-min-microvolt = <3400000>; |
| regulator-max-microvolt = <3400000>; |
| }; |
| }; |
| }; |
| }; |
| |
| &blsp1_uart2 { |
| status = "okay"; |
| }; |
| |
| &blsp2_i2c6 { |
| status = "okay"; |
| |
| fuelgauge@36 { |
| compatible = "maxim,max17048"; |
| reg = <0x36>; |
| |
| maxim,double-soc; |
| maxim,rcomp = /bits/ 8 <0x56>; |
| |
| interrupt-parent = <&pma8084_gpios>; |
| interrupts = <21 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&fuelgauge_pin>; |
| }; |
| }; |
| |
| &blsp2_uart2 { |
| status = "okay"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_uart2_pins_active>; |
| pinctrl-1 = <&blsp2_uart2_pins_sleep>; |
| |
| bluetooth { |
| compatible = "brcm,bcm43540-bt"; |
| max-speed = <3000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_pins>; |
| device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>; |
| shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <75 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "host-wakeup"; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| status = "okay"; |
| |
| vdda-supply = <&pma8084_l2>; |
| vdd-supply = <&pma8084_l22>; |
| vddio-supply = <&pma8084_l12>; |
| |
| panel: panel@0 { |
| reg = <0>; |
| compatible = "samsung,s6e3fa2"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&panel_te_pin &panel_rst_pin>; |
| |
| iovdd-supply = <&pma8084_lvs4>; |
| vddr-supply = <&vreg_panel>; |
| |
| reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <&panel_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi0_phy { |
| status = "okay"; |
| |
| vddio-supply = <&pma8084_l12>; |
| }; |
| |
| &pma8084_gpios { |
| gpio_keys_pin_a: gpio-keys-active-state { |
| pins = "gpio2", "gpio3", "gpio5"; |
| function = "normal"; |
| |
| bias-pull-up; |
| power-source = <PMA8084_GPIO_S4>; |
| }; |
| |
| touchkey_pin: touchkey-int-state { |
| pins = "gpio6"; |
| function = "normal"; |
| bias-disable; |
| input-enable; |
| power-source = <PMA8084_GPIO_S4>; |
| }; |
| |
| touch_pin: touchscreen-int-state { |
| pins = "gpio8"; |
| function = "normal"; |
| bias-disable; |
| input-enable; |
| power-source = <PMA8084_GPIO_S4>; |
| }; |
| |
| panel_en_pin: panel-en-state { |
| pins = "gpio14"; |
| function = "normal"; |
| bias-pull-up; |
| power-source = <PMA8084_GPIO_S4>; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| }; |
| |
| wlan_sleep_clk_pin: wlan-sleep-clk-state { |
| pins = "gpio16"; |
| function = "func2"; |
| |
| output-high; |
| power-source = <PMA8084_GPIO_S4>; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; |
| }; |
| |
| panel_rst_pin: panel-rst-state { |
| pins = "gpio17"; |
| function = "normal"; |
| bias-disable; |
| power-source = <PMA8084_GPIO_S4>; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| }; |
| |
| fuelgauge_pin: fuelgauge-int-state { |
| pins = "gpio21"; |
| function = "normal"; |
| bias-disable; |
| input-enable; |
| power-source = <PMA8084_GPIO_S4>; |
| }; |
| }; |
| |
| &reserved_memory { |
| ramoops@3e8e0000 { |
| compatible = "ramoops"; |
| reg = <0x3e8e0000 0x200000>; |
| |
| console-size = <0x100000>; |
| record-size = <0x10000>; |
| ftrace-size = <0x10000>; |
| pmsg-size = <0x80000>; |
| ecc-size = <8>; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| status = "okay"; |
| cx-supply = <&pma8084_s2>; |
| }; |
| |
| &remoteproc_mss { |
| status = "okay"; |
| cx-supply = <&pma8084_s2>; |
| mss-supply = <&pma8084_s6>; |
| mx-supply = <&pma8084_s1>; |
| pll-supply = <&pma8084_l12>; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pma8084-regulators"; |
| |
| pma8084_s1: s1 { |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-always-on; |
| }; |
| |
| pma8084_s2: s2 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pma8084_s3: s3 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| pma8084_s4: s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pma8084_s5: s5 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| }; |
| |
| pma8084_s6: s6 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pma8084_l1: l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pma8084_l2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pma8084_l3: l3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pma8084_l4: l4 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pma8084_l5: l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pma8084_l6: l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pma8084_l7: l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pma8084_l8: l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pma8084_l9: l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pma8084_l10: l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pma8084_l11: l11 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| pma8084_l12: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| pma8084_l13: l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pma8084_l14: l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pma8084_l15: l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pma8084_l16: l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| pma8084_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pma8084_l18: l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pma8084_l19: l19 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| pma8084_l20: l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| }; |
| |
| pma8084_l21: l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| }; |
| |
| pma8084_l22: l22 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| pma8084_l23: l23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| pma8084_l24: l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| }; |
| |
| pma8084_l25: l25 { |
| regulator-min-microvolt = <2100000>; |
| regulator-max-microvolt = <2100000>; |
| }; |
| |
| pma8084_l26: l26 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pma8084_l27: l27 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pma8084_lvs1: lvs1 {}; |
| pma8084_lvs2: lvs2 {}; |
| pma8084_lvs3: lvs3 {}; |
| pma8084_lvs4: lvs4 {}; |
| |
| pma8084_5vs1: 5vs1 {}; |
| }; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| |
| vmmc-supply = <&pma8084_l20>; |
| vqmmc-supply = <&pma8084_s4>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_on>; |
| pinctrl-1 = <&sdc1_off>; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| max-frequency = <100000000>; |
| vmmc-supply = <&vreg_wlan>; |
| vqmmc-supply = <&pma8084_s4>; |
| non-removable; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_on>; |
| pinctrl-1 = <&sdc2_off>; |
| |
| wifi@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| |
| /* |
| * Allow all klte* variants to load the same NVRAM file, |
| * as they have little difference in the WiFi part. |
| */ |
| brcm,board-type = "samsung,klte"; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <92 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "host-wake"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>; |
| }; |
| }; |
| |
| &sdhc_3 { |
| status = "okay"; |
| max-frequency = <100000000>; |
| vmmc-supply = <&pma8084_l21>; |
| vqmmc-supply = <&pma8084_l13>; |
| |
| /* |
| * cd-gpio is intentionally disabled. If enabled, an SD card |
| * present during boot is not initialized correctly. Without |
| * cd-gpios the driver resorts to polling, so hotplug works. |
| */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>; |
| /* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */ |
| }; |
| |
| &tlmm { |
| /* This seems suspicious, but somebody with this device should look into it. */ |
| blsp2_uart2_pins_active: blsp2-uart2-pins-active-state { |
| pins = "gpio45", "gpio46", "gpio47", "gpio48"; |
| function = "blsp_uart8"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state { |
| pins = "gpio45", "gpio46", "gpio47", "gpio48"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| bt_pins: bt-pins-state { |
| hostwake-pins { |
| pins = "gpio75"; |
| function = "gpio"; |
| drive-strength = <16>; |
| }; |
| |
| devwake-pins { |
| pins = "gpio91"; |
| function = "gpio"; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| sdc1_on: sdhc1-on-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| drive-strength = <4>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <4>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdc3_on: sdc3-on-state { |
| pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40"; |
| function = "sdc3"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| sdhc3_cd_pin: sdc3-cd-on-state { |
| pins = "gpio62"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| sdc2_on: sdhc2-on-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc2_cmd", "sdc2_data"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| |
| i2c_touchkey_pins: i2c-touchkey-state { |
| pins = "gpio95", "gpio96"; |
| function = "gpio"; |
| bias-pull-up; |
| }; |
| |
| i2c_led_gpioex_pins: i2c-led-gpioex-state { |
| function = "gpio"; |
| bias-pull-down; |
| }; |
| |
| gpioex_pin: gpioex-state { |
| pins = "gpio145"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| wifi_pin: wifi-state { |
| pins = "gpio92"; |
| function = "gpio"; |
| bias-pull-down; |
| }; |
| |
| panel_te_pin: panel-state { |
| pins = "gpio12"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| &usb { |
| status = "okay"; |
| |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| }; |
| |
| &usb_hs1_phy { |
| status = "okay"; |
| |
| v1p8-supply = <&pma8084_l6>; |
| v3p3-supply = <&pma8084_l24>; |
| |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| }; |
