// SPDX-License-Identifier: GPL-2.0
/dts-v1/;

#include "skeleton.dtsi"
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
#include <dt-bindings/reset/qcom,gcc-msm8960.h>
#include <dt-bindings/clock/qcom,mmcc-msm8960.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
	model = "Qualcomm APQ8064";
	compatible = "qcom,apq8064";
	interrupt-parent = <&intc>;

	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		smem_region: smem@80000000 {
			reg = <0x80000000 0x200000>;
			no-map;
		};

		wcnss_mem: wcnss@8f000000 {
			reg = <0x8f000000 0x700000>;
			no-map;
		};
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <0>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc0>;
			qcom,saw = <&saw0>;
			cpu-idle-states = <&CPU_SPC>;
		};

		CPU1: cpu@1 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <1>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc1>;
			qcom,saw = <&saw1>;
			cpu-idle-states = <&CPU_SPC>;
		};

		CPU2: cpu@2 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <2>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc2>;
			qcom,saw = <&saw2>;
			cpu-idle-states = <&CPU_SPC>;
		};

		CPU3: cpu@3 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <3>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc3>;
			qcom,saw = <&saw3>;
			cpu-idle-states = <&CPU_SPC>;
		};

		L2: l2-cache {
			compatible = "cache";
			cache-level = <2>;
		};

		idle-states {
			CPU_SPC: spc {
				compatible = "qcom,idle-state-spc",
						"arm,idle-state";
				entry-latency-us = <400>;
				exit-latency-us = <900>;
				min-residency-us = <3000>;
			};
		};
	};

	thermal-zones {
		cpu-thermal0 {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&gcc 7>;
			coefficients = <1199 0>;

			trips {
				cpu_alert0: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit0: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu-thermal1 {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&gcc 8>;
			coefficients = <1132 0>;

			trips {
				cpu_alert1: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit1: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu-thermal2 {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&gcc 9>;
			coefficients = <1199 0>;

			trips {
				cpu_alert2: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit2: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu-thermal3 {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&gcc 10>;
			coefficients = <1132 0>;

			trips {
				cpu_alert3: trip0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit3: trip1 {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};
	};

	cpu-pmu {
		compatible = "qcom,krait-pmu";
		interrupts = <1 10 0x304>;
	};

	clocks {
		cxo_board: cxo_board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <19200000>;
		};

		pxo_board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <27000000>;
		};

		sleep_clk: sleep_clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32768>;
		};
	};

	sfpb_mutex: hwmutex {
		compatible = "qcom,sfpb-mutex";
		syscon = <&sfpb_wrapper_mutex 0x604 0x4>;
		#hwlock-cells = <1>;
	};

	smem {
		compatible = "qcom,smem";
		memory-region = <&smem_region>;

		hwlocks = <&sfpb_mutex 3>;
	};

	smd {
		compatible = "qcom,smd";

		modem@0 {
			interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;

			qcom,ipc = <&l2cc 8 3>;
			qcom,smd-edge = <0>;

			status = "disabled";
		};

		q6@1 {
			interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;

			qcom,ipc = <&l2cc 8 15>;
			qcom,smd-edge = <1>;

			status = "disabled";
		};

		dsps@3 {
			interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;

			qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
			qcom,smd-edge = <3>;

			status = "disabled";
		};

		riva@6 {
			interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;

			qcom,ipc = <&l2cc 8 25>;
			qcom,smd-edge = <6>;

			status = "disabled";
		};
	};

	smsm {
		compatible = "qcom,smsm";

		#address-cells = <1>;
		#size-cells = <0>;

		qcom,ipc-1 = <&l2cc 8 4>;
		qcom,ipc-2 = <&l2cc 8 14>;
		qcom,ipc-3 = <&l2cc 8 23>;
		qcom,ipc-4 = <&sps_sic_non_secure 0x4094 0>;

		apps_smsm: apps@0 {
			reg = <0>;
			#qcom,smem-state-cells = <1>;
		};

		modem_smsm: modem@1 {
			reg = <1>;
			interrupts = <0 38 IRQ_TYPE_EDGE_RISING>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		q6_smsm: q6@2 {
			reg = <2>;
			interrupts = <0 89 IRQ_TYPE_EDGE_RISING>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		wcnss_smsm: wcnss@3 {
			reg = <3>;
			interrupts = <0 204 IRQ_TYPE_EDGE_RISING>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		dsps_smsm: dsps@4 {
			reg = <4>;
			interrupts = <0 137 IRQ_TYPE_EDGE_RISING>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	firmware {
		scm {
			compatible = "qcom,scm-apq8064";

			clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
			clock-names = "core";
		};
	};

	soc: soc {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;
		compatible = "simple-bus";

		tlmm_pinmux: pinctrl@800000 {
			compatible = "qcom,apq8064-pinctrl";
			reg = <0x800000 0x4000>;

			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;

			pinctrl-names = "default";
			pinctrl-0 = <&ps_hold>;
		};

		sfpb_wrapper_mutex: syscon@1200000 {
			compatible = "syscon";
			reg = <0x01200000 0x8000>;
		};

		intc: interrupt-controller@2000000 {
			compatible = "qcom,msm-qgic2";
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0x02000000 0x1000>,
			      <0x02002000 0x1000>;
		};

		timer@200a000 {
			compatible = "qcom,kpss-timer",
				     "qcom,kpss-wdt-apq8064", "qcom,msm-timer";
			interrupts = <1 1 0x301>,
				     <1 2 0x301>,
				     <1 3 0x301>;
			reg = <0x0200a000 0x100>;
			clock-frequency = <27000000>,
					  <32768>;
			cpu-offset = <0x80000>;
		};

		acc0: clock-controller@2088000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
		};

		acc1: clock-controller@2098000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
		};

		acc2: clock-controller@20a8000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
		};

		acc3: clock-controller@20b8000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
		};

		saw0: power-controller@2089000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		saw1: power-controller@2099000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		saw2: power-controller@20a9000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		saw3: power-controller@20b9000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		sps_sic_non_secure: sps-sic-non-secure@12100000 {
			compatible	= "syscon";
			reg		= <0x12100000 0x10000>;
		};

		gsbi1: gsbi@12440000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <1>;
			reg = <0x12440000 0x100>;
			clocks = <&gcc GSBI1_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			syscon-tcsr = <&tcsr>;

			gsbi1_serial: serial@12450000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x12450000 0x100>,
				      <0x12400000 0x03>;
				interrupts = <0 193 0x0>;
				clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};

			gsbi1_i2c: i2c@12460000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				pinctrl-0 = <&i2c1_pins>;
				pinctrl-1 = <&i2c1_pins_sleep>;
				pinctrl-names = "default", "sleep";
				reg = <0x12460000 0x1000>;
				interrupts = <0 194 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
				clock-names = "core", "iface";
				#address-cells = <1>;
				#size-cells = <0>;
			};

		};

		gsbi2: gsbi@12480000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <2>;
			reg = <0x12480000 0x100>;
			clocks = <&gcc GSBI2_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			syscon-tcsr = <&tcsr>;

			gsbi2_i2c: i2c@124a0000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				reg = <0x124a0000 0x1000>;
				pinctrl-0 = <&i2c2_pins>;
				pinctrl-1 = <&i2c2_pins_sleep>;
				pinctrl-names = "default", "sleep";
				interrupts = <0 196 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
				clock-names = "core", "iface";
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gsbi3: gsbi@16200000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <3>;
			reg = <0x16200000 0x100>;
			clocks = <&gcc GSBI3_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			gsbi3_i2c: i2c@16280000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				pinctrl-0 = <&i2c3_pins>;
				pinctrl-1 = <&i2c3_pins_sleep>;
				pinctrl-names = "default", "sleep";
				reg = <0x16280000 0x1000>;
				interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI3_QUP_CLK>,
					 <&gcc GSBI3_H_CLK>;
				clock-names = "core", "iface";
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gsbi4: gsbi@16300000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <4>;
			reg = <0x16300000 0x03>;
			clocks = <&gcc GSBI4_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			gsbi4_i2c: i2c@16380000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				pinctrl-0 = <&i2c4_pins>;
				pinctrl-1 = <&i2c4_pins_sleep>;
				pinctrl-names = "default", "sleep";
				reg = <0x16380000 0x1000>;
				interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI4_QUP_CLK>,
					 <&gcc GSBI4_H_CLK>;
				clock-names = "core", "iface";
			};
		};

		gsbi5: gsbi@1a200000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <5>;
			reg = <0x1a200000 0x03>;
			clocks = <&gcc GSBI5_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			gsbi5_serial: serial@1a240000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x1a240000 0x100>,
				      <0x1a200000 0x03>;
				interrupts = <0 154 0x0>;
				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};

			gsbi5_spi: spi@1a280000 {
				compatible = "qcom,spi-qup-v1.1.1";
				reg = <0x1a280000 0x1000>;
				interrupts = <0 155 0>;
				pinctrl-0 = <&spi5_default>;
				pinctrl-1 = <&spi5_sleep>;
				pinctrl-names = "default", "sleep";
				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gsbi6: gsbi@16500000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <6>;
			reg = <0x16500000 0x03>;
			clocks = <&gcc GSBI6_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			gsbi6_serial: serial@16540000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x16540000 0x100>,
				      <0x16500000 0x03>;
				interrupts = <0 156 0x0>;
				clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};

			gsbi6_i2c: i2c@16580000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				pinctrl-0 = <&i2c6_pins>;
				pinctrl-1 = <&i2c6_pins_sleep>;
				pinctrl-names = "default", "sleep";
				reg = <0x16580000 0x1000>;
				interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI6_QUP_CLK>,
					 <&gcc GSBI6_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};
		};

		gsbi7: gsbi@16600000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <7>;
			reg = <0x16600000 0x100>;
			clocks = <&gcc GSBI7_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			syscon-tcsr = <&tcsr>;

			gsbi7_serial: serial@16640000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x16640000 0x1000>,
				      <0x16600000 0x1000>;
				interrupts = <0 158 0x0>;
				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};

			gsbi7_i2c: i2c@16680000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				pinctrl-0 = <&i2c7_pins>;
				pinctrl-1 = <&i2c7_pins_sleep>;
				pinctrl-names = "default", "sleep";
				reg = <0x16680000 0x1000>;
				interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI7_QUP_CLK>,
					 <&gcc GSBI7_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};
		};

		rng@1a500000 {
			compatible = "qcom,prng";
			reg = <0x1a500000 0x200>;
			clocks = <&gcc PRNG_CLK>;
			clock-names = "core";
		};

		ssbi@c00000 {
			compatible = "qcom,ssbi";
			reg = <0x00c00000 0x1000>;
			qcom,controller-type = "pmic-arbiter";

			pm8821: pmic@1 {
				compatible = "qcom,pm8821";
				interrupt-parent = <&tlmm_pinmux>;
				interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
				#interrupt-cells = <2>;
				interrupt-controller;
				#address-cells = <1>;
				#size-cells = <0>;

				pm8821_mpps: mpps@50 {
					compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
					reg = <0x50>;
					interrupts = <24 IRQ_TYPE_NONE>,
						     <25 IRQ_TYPE_NONE>,
						     <26 IRQ_TYPE_NONE>,
						     <27 IRQ_TYPE_NONE>;
					gpio-controller;
					#gpio-cells = <2>;
				};
			};
		};

		qcom,ssbi@500000 {
			compatible = "qcom,ssbi";
			reg = <0x00500000 0x1000>;
			qcom,controller-type = "pmic-arbiter";

			pmicintc: pmic@0 {
				compatible = "qcom,pm8921";
				interrupt-parent = <&tlmm_pinmux>;
				interrupts = <74 8>;
				#interrupt-cells = <2>;
				interrupt-controller;
				#address-cells = <1>;
				#size-cells = <0>;

				pm8921_gpio: gpio@150 {

					compatible = "qcom,pm8921-gpio",
						     "qcom,ssbi-gpio";
					reg = <0x150>;
					interrupts = <192 IRQ_TYPE_NONE>,
						     <193 IRQ_TYPE_NONE>,
						     <194 IRQ_TYPE_NONE>,
						     <195 IRQ_TYPE_NONE>,
						     <196 IRQ_TYPE_NONE>,
						     <197 IRQ_TYPE_NONE>,
						     <198 IRQ_TYPE_NONE>,
						     <199 IRQ_TYPE_NONE>,
						     <200 IRQ_TYPE_NONE>,
						     <201 IRQ_TYPE_NONE>,
						     <202 IRQ_TYPE_NONE>,
						     <203 IRQ_TYPE_NONE>,
						     <204 IRQ_TYPE_NONE>,
						     <205 IRQ_TYPE_NONE>,
						     <206 IRQ_TYPE_NONE>,
						     <207 IRQ_TYPE_NONE>,
						     <208 IRQ_TYPE_NONE>,
						     <209 IRQ_TYPE_NONE>,
						     <210 IRQ_TYPE_NONE>,
						     <211 IRQ_TYPE_NONE>,
						     <212 IRQ_TYPE_NONE>,
						     <213 IRQ_TYPE_NONE>,
						     <214 IRQ_TYPE_NONE>,
						     <215 IRQ_TYPE_NONE>,
						     <216 IRQ_TYPE_NONE>,
						     <217 IRQ_TYPE_NONE>,
						     <218 IRQ_TYPE_NONE>,
						     <219 IRQ_TYPE_NONE>,
						     <220 IRQ_TYPE_NONE>,
						     <221 IRQ_TYPE_NONE>,
						     <222 IRQ_TYPE_NONE>,
						     <223 IRQ_TYPE_NONE>,
						     <224 IRQ_TYPE_NONE>,
						     <225 IRQ_TYPE_NONE>,
						     <226 IRQ_TYPE_NONE>,
						     <227 IRQ_TYPE_NONE>,
						     <228 IRQ_TYPE_NONE>,
						     <229 IRQ_TYPE_NONE>,
						     <230 IRQ_TYPE_NONE>,
						     <231 IRQ_TYPE_NONE>,
						     <232 IRQ_TYPE_NONE>,
						     <233 IRQ_TYPE_NONE>,
						     <234 IRQ_TYPE_NONE>,
						     <235 IRQ_TYPE_NONE>;
					gpio-controller;
					#gpio-cells = <2>;

				};

				pm8921_mpps: mpps@50 {
					compatible = "qcom,pm8921-mpp",
						     "qcom,ssbi-mpp";
					reg = <0x50>;
					gpio-controller;
					#gpio-cells = <2>;
					interrupts =
					<128 IRQ_TYPE_NONE>,
					<129 IRQ_TYPE_NONE>,
					<130 IRQ_TYPE_NONE>,
					<131 IRQ_TYPE_NONE>,
					<132 IRQ_TYPE_NONE>,
					<133 IRQ_TYPE_NONE>,
					<134 IRQ_TYPE_NONE>,
					<135 IRQ_TYPE_NONE>,
					<136 IRQ_TYPE_NONE>,
					<137 IRQ_TYPE_NONE>,
					<138 IRQ_TYPE_NONE>,
					<139 IRQ_TYPE_NONE>;
				};

				rtc@11d {
					compatible = "qcom,pm8921-rtc";
					interrupt-parent = <&pmicintc>;
					interrupts = <39 1>;
					reg = <0x11d>;
					allow-set-time;
				};

				pwrkey@1c {
					compatible = "qcom,pm8921-pwrkey";
					reg = <0x1c>;
					interrupt-parent = <&pmicintc>;
					interrupts = <50 1>, <51 1>;
					debounce = <15625>;
					pull-up;
				};
			};
		};

		qfprom: qfprom@700000 {
			compatible	= "qcom,qfprom";
			reg		= <0x00700000 0x1000>;
			#address-cells	= <1>;
			#size-cells	= <1>;
			ranges;
			tsens_calib: calib {
				reg = <0x404 0x10>;
			};
			tsens_backup: backup_calib {
				reg = <0x414 0x10>;
			};
		};

		gcc: clock-controller@900000 {
			compatible = "qcom,gcc-apq8064";
			reg = <0x00900000 0x4000>;
			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
			nvmem-cell-names = "calib", "calib_backup";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#thermal-sensor-cells = <1>;
		};

		lcc: clock-controller@28000000 {
			compatible = "qcom,lcc-apq8064";
			reg = <0x28000000 0x1000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		mmcc: clock-controller@4000000 {
			compatible = "qcom,mmcc-apq8064";
			reg = <0x4000000 0x1000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		l2cc: clock-controller@2011000 {
			compatible	= "syscon";
			reg		= <0x2011000 0x1000>;
		};

		rpm@108000 {
			compatible	= "qcom,rpm-apq8064";
			reg		= <0x108000 0x1000>;
			qcom,ipc	= <&l2cc 0x8 2>;

			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
			interrupt-names	= "ack", "err", "wakeup";

			rpmcc: clock-controller {
				compatible	= "qcom,rpmcc-apq8064", "qcom,rpmcc";
				#clock-cells = <1>;
			};

			regulators {
				compatible = "qcom,rpm-pm8921-regulators";

				pm8921_s1: s1 {};
				pm8921_s2: s2 {};
				pm8921_s3: s3 {};
				pm8921_s4: s4 {};
				pm8921_s7: s7 {};
				pm8921_s8: s8 {};

				pm8921_l1: l1 {};
				pm8921_l2: l2 {};
				pm8921_l3: l3 {};
				pm8921_l4: l4 {};
				pm8921_l5: l5 {};
				pm8921_l6: l6 {};
				pm8921_l7: l7 {};
				pm8921_l8: l8 {};
				pm8921_l9: l9 {};
				pm8921_l10: l10 {};
				pm8921_l11: l11 {};
				pm8921_l12: l12 {};
				pm8921_l14: l14 {};
				pm8921_l15: l15 {};
				pm8921_l16: l16 {};
				pm8921_l17: l17 {};
				pm8921_l18: l18 {};
				pm8921_l21: l21 {};
				pm8921_l22: l22 {};
				pm8921_l23: l23 {};
				pm8921_l24: l24 {};
				pm8921_l25: l25 {};
				pm8921_l26: l26 {};
				pm8921_l27: l27 {};
				pm8921_l28: l28 {};
				pm8921_l29: l29 {};

				pm8921_lvs1: lvs1 {};
				pm8921_lvs2: lvs2 {};
				pm8921_lvs3: lvs3 {};
				pm8921_lvs4: lvs4 {};
				pm8921_lvs5: lvs5 {};
				pm8921_lvs6: lvs6 {};
				pm8921_lvs7: lvs7 {};

				pm8921_usb_switch: usb-switch {};

				pm8921_hdmi_switch: hdmi-switch {
					bias-pull-down;
				};

				pm8921_ncp: ncp {};
			};
		};

		usb1: usb@12500000 {
			compatible = "qcom,ci-hdrc";
			reg = <0x12500000 0x200>,
			      <0x12500200 0x200>;
			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
			clock-names = "core", "iface";
			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
			assigned-clock-rates = <60000000>;
			resets = <&gcc USB_HS1_RESET>;
			reset-names = "core";
			phy_type = "ulpi";
			ahb-burst-config = <0>;
			phys = <&usb_hs1_phy>;
			phy-names = "usb-phy";
			status = "disabled";
			#reset-cells = <1>;

			ulpi {
				usb_hs1_phy: phy {
					compatible = "qcom,usb-hs-phy-apq8064",
						     "qcom,usb-hs-phy";
					clocks = <&sleep_clk>, <&cxo_board>;
					clock-names = "sleep", "ref";
					resets = <&usb1 0>;
					reset-names = "por";
					#phy-cells = <0>;
				};
			};
		};

		usb3: usb@12520000 {
			compatible = "qcom,ci-hdrc";
			reg = <0x12520000 0x200>,
			      <0x12520200 0x200>;
			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
			clock-names = "core", "iface";
			assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
			assigned-clock-rates = <60000000>;
			resets = <&gcc USB_HS3_RESET>;
			reset-names = "core";
			phy_type = "ulpi";
			ahb-burst-config = <0>;
			phys = <&usb_hs3_phy>;
			phy-names = "usb-phy";
			status = "disabled";
			#reset-cells = <1>;

			ulpi {
				usb_hs3_phy: phy {
					compatible = "qcom,usb-hs-phy-apq8064",
						     "qcom,usb-hs-phy";
					#phy-cells = <0>;
					clocks = <&sleep_clk>, <&cxo_board>;
					clock-names = "sleep", "ref";
					resets = <&usb3 0>;
					reset-names = "por";
				};
			};
		};

		usb4: usb@12530000 {
			compatible = "qcom,ci-hdrc";
			reg = <0x12530000 0x200>,
			      <0x12530200 0x200>;
			interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
			clock-names = "core", "iface";
			assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
			assigned-clock-rates = <60000000>;
			resets = <&gcc USB_HS4_RESET>;
			reset-names = "core";
			phy_type = "ulpi";
			ahb-burst-config = <0>;
			phys = <&usb_hs4_phy>;
			phy-names = "usb-phy";
			status = "disabled";
			#reset-cells = <1>;

			ulpi {
				usb_hs4_phy: phy {
					compatible = "qcom,usb-hs-phy-apq8064",
						     "qcom,usb-hs-phy";
					#phy-cells = <0>;
					clocks = <&sleep_clk>, <&cxo_board>;
					clock-names = "sleep", "ref";
					resets = <&usb4 0>;
					reset-names = "por";
				};
			};
		};

		sata_phy0: phy@1b400000 {
			compatible	= "qcom,apq8064-sata-phy";
			status		= "disabled";
			reg		= <0x1b400000 0x200>;
			reg-names	= "phy_mem";
			clocks		= <&gcc SATA_PHY_CFG_CLK>;
			clock-names	= "cfg";
			#phy-cells	= <0>;
		};

		sata0: sata@29000000 {
			compatible		= "qcom,apq8064-ahci", "generic-ahci";
			status			= "disabled";
			reg			= <0x29000000 0x180>;
			interrupts		= <GIC_SPI 209 IRQ_TYPE_NONE>;

			clocks			= <&gcc SFAB_SATA_S_H_CLK>,
						<&gcc SATA_H_CLK>,
						<&gcc SATA_A_CLK>,
						<&gcc SATA_RXOOB_CLK>,
						<&gcc SATA_PMALIVE_CLK>;
			clock-names		= "slave_iface",
						"iface",
						"bus",
						"rxoob",
						"core_pmalive";

			assigned-clocks		= <&gcc SATA_RXOOB_CLK>,
						<&gcc SATA_PMALIVE_CLK>;
			assigned-clock-rates	= <100000000>, <100000000>;

			phys			= <&sata_phy0>;
			phy-names		= "sata-phy";
			ports-implemented	= <0x1>;
		};

		/* Temporary fixed regulator */
		sdcc1bam:dma@12402000{
			compatible = "qcom,bam-v1.3.0";
			reg = <0x12402000 0x8000>;
			interrupts = <0 98 0>;
			clocks = <&gcc SDC1_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		sdcc3bam:dma@12182000{
			compatible = "qcom,bam-v1.3.0";
			reg = <0x12182000 0x8000>;
			interrupts = <0 96 0>;
			clocks = <&gcc SDC3_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		sdcc4bam:dma@121c2000{
			compatible = "qcom,bam-v1.3.0";
			reg = <0x121c2000 0x8000>;
			interrupts = <0 95 0>;
			clocks = <&gcc SDC4_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		amba {
			compatible = "simple-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			sdcc1: sdcc@12400000 {
				status		= "disabled";
				compatible	= "arm,pl18x", "arm,primecell";
				pinctrl-names	= "default";
				pinctrl-0	= <&sdcc1_pins>;
				arm,primecell-periphid = <0x00051180>;
				reg		= <0x12400000 0x2000>;
				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names	= "cmd_irq";
				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
				clock-names	= "mclk", "apb_pclk";
				bus-width	= <8>;
				max-frequency	= <96000000>;
				non-removable;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
				dma-names = "tx", "rx";
			};

			sdcc3: sdcc@12180000 {
				compatible	= "arm,pl18x", "arm,primecell";
				arm,primecell-periphid = <0x00051180>;
				status		= "disabled";
				reg		= <0x12180000 0x2000>;
				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names	= "cmd_irq";
				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
				clock-names	= "mclk", "apb_pclk";
				bus-width	= <4>;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				max-frequency	= <192000000>;
				no-1-8-v;
				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
				dma-names = "tx", "rx";
			};

			sdcc4: sdcc@121c0000 {
				compatible	= "arm,pl18x", "arm,primecell";
				arm,primecell-periphid = <0x00051180>;
				status		= "disabled";
				reg		= <0x121c0000 0x2000>;
				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names	= "cmd_irq";
				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
				clock-names	= "mclk", "apb_pclk";
				bus-width	= <4>;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				max-frequency	= <48000000>;
				dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
				dma-names = "tx", "rx";
				pinctrl-names = "default";
				pinctrl-0 = <&sdc4_gpios>;
			};
		};

		tcsr: syscon@1a400000 {
			compatible = "qcom,tcsr-apq8064", "syscon";
			reg = <0x1a400000 0x100>;
		};

		gpu: adreno-3xx@4300000 {
			compatible = "qcom,adreno-3xx";
			reg = <0x04300000 0x20000>;
			reg-names = "kgsl_3d0_reg_memory";
			interrupts = <GIC_SPI 80 0>;
			interrupt-names = "kgsl_3d0_irq";
			clock-names =
			    "core_clk",
			    "iface_clk",
			    "mem_clk",
			    "mem_iface_clk";
			clocks =
			    <&mmcc GFX3D_CLK>,
			    <&mmcc GFX3D_AHB_CLK>,
			    <&mmcc GFX3D_AXI_CLK>,
			    <&mmcc MMSS_IMEM_AHB_CLK>;
			qcom,chipid = <0x03020002>;

			iommus = <&gfx3d 0
				  &gfx3d 1
				  &gfx3d 2
				  &gfx3d 3
				  &gfx3d 4
				  &gfx3d 5
				  &gfx3d 6
				  &gfx3d 7
				  &gfx3d 8
				  &gfx3d 9
				  &gfx3d 10
				  &gfx3d 11
				  &gfx3d 12
				  &gfx3d 13
				  &gfx3d 14
				  &gfx3d 15
				  &gfx3d 16
				  &gfx3d 17
				  &gfx3d 18
				  &gfx3d 19
				  &gfx3d 20
				  &gfx3d 21
				  &gfx3d 22
				  &gfx3d 23
				  &gfx3d 24
				  &gfx3d 25
				  &gfx3d 26
				  &gfx3d 27
				  &gfx3d 28
				  &gfx3d 29
				  &gfx3d 30
				  &gfx3d 31
				  &gfx3d1 0
				  &gfx3d1 1
				  &gfx3d1 2
				  &gfx3d1 3
				  &gfx3d1 4
				  &gfx3d1 5
				  &gfx3d1 6
				  &gfx3d1 7
				  &gfx3d1 8
				  &gfx3d1 9
				  &gfx3d1 10
				  &gfx3d1 11
				  &gfx3d1 12
				  &gfx3d1 13
				  &gfx3d1 14
				  &gfx3d1 15
				  &gfx3d1 16
				  &gfx3d1 17
				  &gfx3d1 18
				  &gfx3d1 19
				  &gfx3d1 20
				  &gfx3d1 21
				  &gfx3d1 22
				  &gfx3d1 23
				  &gfx3d1 24
				  &gfx3d1 25
				  &gfx3d1 26
				  &gfx3d1 27
				  &gfx3d1 28
				  &gfx3d1 29
				  &gfx3d1 30
				  &gfx3d1 31>;

			qcom,gpu-pwrlevels {
				compatible = "qcom,gpu-pwrlevels";
				qcom,gpu-pwrlevel@0 {
					qcom,gpu-freq = <450000000>;
				};
				qcom,gpu-pwrlevel@1 {
					qcom,gpu-freq = <27000000>;
				};
			};
		};

		mmss_sfpb: syscon@5700000 {
			compatible = "syscon";
			reg = <0x5700000 0x70>;
		};

		dsi0: mdss_dsi@4700000 {
			compatible = "qcom,mdss-dsi-ctrl";
			label = "MDSS DSI CTRL->0";
			#address-cells = <1>;
			#size-cells = <0>;
			interrupts = <GIC_SPI 82 0>;
			reg = <0x04700000 0x200>;
			reg-names = "dsi_ctrl";

			clocks = <&mmcc DSI_M_AHB_CLK>,
				<&mmcc DSI_S_AHB_CLK>,
				<&mmcc AMP_AHB_CLK>,
				<&mmcc DSI_CLK>,
				<&mmcc DSI1_BYTE_CLK>,
				<&mmcc DSI_PIXEL_CLK>,
				<&mmcc DSI1_ESC_CLK>;
			clock-names = "iface_clk", "bus_clk", "core_mmss_clk",
					"src_clk", "byte_clk", "pixel_clk",
					"core_clk";

			assigned-clocks = <&mmcc DSI1_BYTE_SRC>,
					<&mmcc DSI1_ESC_SRC>,
					<&mmcc DSI_SRC>,
					<&mmcc DSI_PIXEL_SRC>;
			assigned-clock-parents = <&dsi0_phy 0>,
						<&dsi0_phy 0>,
						<&dsi0_phy 1>,
						<&dsi0_phy 1>;
			syscon-sfpb = <&mmss_sfpb>;
			phys = <&dsi0_phy>;
			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					dsi0_in: endpoint {
					};
				};

				port@1 {
					reg = <1>;
					dsi0_out: endpoint {
					};
				};
			};
		};


		dsi0_phy: dsi-phy@4700200 {
			compatible = "qcom,dsi-phy-28nm-8960";
			#clock-cells = <1>;
			#phy-cells = <0>;

			reg = <0x04700200 0x100>,
				<0x04700300 0x200>,
				<0x04700500 0x5c>;
			reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
			clock-names = "iface_clk";
			clocks = <&mmcc DSI_M_AHB_CLK>;
		};


		mdp_port0: iommu@7500000 {
			compatible = "qcom,apq8064-iommu";
			#iommu-cells = <1>;
			clock-names =
			    "smmu_pclk",
			    "iommu_clk";
			clocks =
			    <&mmcc SMMU_AHB_CLK>,
			    <&mmcc MDP_AXI_CLK>;
			reg = <0x07500000 0x100000>;
			interrupts =
			    <GIC_SPI 63 0>,
			    <GIC_SPI 64 0>;
			qcom,ncb = <2>;
		};

		mdp_port1: iommu@7600000 {
			compatible = "qcom,apq8064-iommu";
			#iommu-cells = <1>;
			clock-names =
			    "smmu_pclk",
			    "iommu_clk";
			clocks =
			    <&mmcc SMMU_AHB_CLK>,
			    <&mmcc MDP_AXI_CLK>;
			reg = <0x07600000 0x100000>;
			interrupts =
			    <GIC_SPI 61 0>,
			    <GIC_SPI 62 0>;
			qcom,ncb = <2>;
		};

		gfx3d: iommu@7c00000 {
			compatible = "qcom,apq8064-iommu";
			#iommu-cells = <1>;
			clock-names =
			    "smmu_pclk",
			    "iommu_clk";
			clocks =
			    <&mmcc SMMU_AHB_CLK>,
			    <&mmcc GFX3D_AXI_CLK>;
			reg = <0x07c00000 0x100000>;
			interrupts =
			    <GIC_SPI 69 0>,
			    <GIC_SPI 70 0>;
			qcom,ncb = <3>;
		};

		gfx3d1: iommu@7d00000 {
			compatible = "qcom,apq8064-iommu";
			#iommu-cells = <1>;
			clock-names =
			    "smmu_pclk",
			    "iommu_clk";
			clocks =
			    <&mmcc SMMU_AHB_CLK>,
			    <&mmcc GFX3D_AXI_CLK>;
			reg = <0x07d00000 0x100000>;
			interrupts =
			    <GIC_SPI 210 0>,
			    <GIC_SPI 211 0>;
			qcom,ncb = <3>;
		};

		pcie: pci@1b500000 {
			compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
			reg = <0x1b500000 0x1000
			       0x1b502000 0x80
			       0x1b600000 0x100
			       0x0ff00000 0x100000>;
			reg-names = "dbi", "elbi", "parf", "config";
			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000   /* I/O */
				  0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */
			interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
			clocks = <&gcc PCIE_A_CLK>,
				 <&gcc PCIE_H_CLK>,
				 <&gcc PCIE_PHY_REF_CLK>;
			clock-names = "core", "iface", "phy";
			resets = <&gcc PCIE_ACLK_RESET>,
				 <&gcc PCIE_HCLK_RESET>,
				 <&gcc PCIE_POR_RESET>,
				 <&gcc PCIE_PCI_RESET>,
				 <&gcc PCIE_PHY_RESET>;
			reset-names = "axi", "ahb", "por", "pci", "phy";
			status = "disabled";
		};

		hdmi: hdmi-tx@4a00000 {
			compatible = "qcom,hdmi-tx-8960";
			pinctrl-names = "default";
			pinctrl-0 = <&hdmi_pinctrl>;
			reg = <0x04a00000 0x2f0>;
			reg-names = "core_physical";
			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&mmcc HDMI_APP_CLK>,
				 <&mmcc HDMI_M_AHB_CLK>,
				 <&mmcc HDMI_S_AHB_CLK>;
			clock-names = "core_clk",
				      "master_iface_clk",
				      "slave_iface_clk";

			phys = <&hdmi_phy>;
			phy-names = "hdmi-phy";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					hdmi_in: endpoint {
					};
				};

				port@1 {
					reg = <1>;
					hdmi_out: endpoint {
					};
				};
			};
		};

		hdmi_phy: hdmi-phy@4a00400 {
			compatible = "qcom,hdmi-phy-8960";
			reg = <0x4a00400 0x60>,
			      <0x4a00500 0x100>;
			reg-names = "hdmi_phy",
				    "hdmi_pll";

			clocks = <&mmcc HDMI_S_AHB_CLK>;
			clock-names = "slave_iface_clk";
			#phy-cells = <0>;
		};

		mdp: mdp@5100000 {
			compatible = "qcom,mdp4";
			reg = <0x05100000 0xf0000>;
			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&mmcc MDP_CLK>,
				 <&mmcc MDP_AHB_CLK>,
				 <&mmcc MDP_AXI_CLK>,
				 <&mmcc MDP_LUT_CLK>,
				 <&mmcc HDMI_TV_CLK>,
				 <&mmcc MDP_TV_CLK>;
			clock-names = "core_clk",
				      "iface_clk",
				      "bus_clk",
				      "lut_clk",
				      "hdmi_clk",
				      "tv_clk";

			iommus = <&mdp_port0 0
				  &mdp_port0 2
				  &mdp_port1 0
				  &mdp_port1 2>;

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					mdp_lvds_out: endpoint {
					};
				};

				port@1 {
					reg = <1>;
					mdp_dsi1_out: endpoint {
					};
				};

				port@2 {
					reg = <2>;
					mdp_dsi2_out: endpoint {
					};
				};

				port@3 {
					reg = <3>;
					mdp_dtv_out: endpoint {
					};
				};
			};
		};

		riva: riva-pil@3204000 {
			compatible = "qcom,riva-pil";

			reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
			reg-names = "ccu", "dxe", "pmu";

			interrupts-extended = <&intc GIC_SPI 199 IRQ_TYPE_EDGE_RISING>,
					      <&wcnss_smsm 6 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal";

			memory-region = <&wcnss_mem>;

			vddcx-supply = <&pm8921_s3>;
			vddmx-supply = <&pm8921_l24>;
			vddpx-supply = <&pm8921_s4>;

			status = "disabled";

			iris {
				compatible = "qcom,wcn3660";

				clocks = <&cxo_board>;
				clock-names = "xo";

				vddxo-supply = <&pm8921_l4>;
				vddrfa-supply = <&pm8921_s2>;
				vddpa-supply = <&pm8921_l10>;
				vdddig-supply = <&pm8921_lvs2>;
			};

			smd-edge {
				interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_RISING>;

				qcom,ipc = <&l2cc 8 25>;
				qcom,smd-edge = <6>;

				label = "riva";

				wcnss {
					compatible = "qcom,wcnss";
					qcom,smd-channels = "WCNSS_CTRL";

					qcom,mmio = <&riva>;

					bt {
						compatible = "qcom,wcnss-bt";
					};

					wifi {
						compatible = "qcom,wcnss-wlan";

						interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
							     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
						interrupt-names = "tx", "rx";

						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
						qcom,smem-state-names = "tx-enable", "tx-rings-empty";
					};
				};
			};
		};

		etb@1a01000 {
			compatible = "coresight-etb10", "arm,primecell";
			reg = <0x1a01000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			port {
				etb_in: endpoint {
					slave-mode;
					remote-endpoint = <&replicator_out0>;
				};
			};
		};

		tpiu@1a03000 {
			compatible = "arm,coresight-tpiu", "arm,primecell";
			reg = <0x1a03000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			port {
				tpiu_in: endpoint {
					slave-mode;
					remote-endpoint = <&replicator_out1>;
				};
			};
		};

		replicator {
			compatible = "arm,coresight-replicator";

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					replicator_out0: endpoint {
						remote-endpoint = <&etb_in>;
					};
				};
				port@1 {
					reg = <1>;
					replicator_out1: endpoint {
						remote-endpoint = <&tpiu_in>;
					};
				};
				port@2 {
					reg = <0>;
					replicator_in: endpoint {
						slave-mode;
						remote-endpoint = <&funnel_out>;
					};
				};
			};
		};

		funnel@1a04000 {
			compatible = "arm,coresight-funnel", "arm,primecell";
			reg = <0x1a04000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				/*
				 * Not described input ports:
				 * 2 - connected to STM component
				 * 3 - not-connected
				 * 6 - not-connected
				 * 7 - not-connected
				 */
				port@0 {
					reg = <0>;
					funnel_in0: endpoint {
						slave-mode;
						remote-endpoint = <&etm0_out>;
					};
				};
				port@1 {
					reg = <1>;
					funnel_in1: endpoint {
						slave-mode;
						remote-endpoint = <&etm1_out>;
					};
				};
				port@4 {
					reg = <4>;
					funnel_in4: endpoint {
						slave-mode;
						remote-endpoint = <&etm2_out>;
					};
				};
				port@5 {
					reg = <5>;
					funnel_in5: endpoint {
						slave-mode;
						remote-endpoint = <&etm3_out>;
					};
				};
				port@8 {
					reg = <0>;
					funnel_out: endpoint {
						remote-endpoint = <&replicator_in>;
					};
				};
			};
		};

		etm@1a1c000 {
			compatible = "arm,coresight-etm3x", "arm,primecell";
			reg = <0x1a1c000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU0>;

			port {
				etm0_out: endpoint {
					remote-endpoint = <&funnel_in0>;
				};
			};
		};

		etm@1a1d000 {
			compatible = "arm,coresight-etm3x", "arm,primecell";
			reg = <0x1a1d000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU1>;

			port {
				etm1_out: endpoint {
					remote-endpoint = <&funnel_in1>;
				};
			};
		};

		etm@1a1e000 {
			compatible = "arm,coresight-etm3x", "arm,primecell";
			reg = <0x1a1e000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU2>;

			port {
				etm2_out: endpoint {
					remote-endpoint = <&funnel_in4>;
				};
			};
		};

		etm@1a1f000 {
			compatible = "arm,coresight-etm3x", "arm,primecell";
			reg = <0x1a1f000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU3>;

			port {
				etm3_out: endpoint {
					remote-endpoint = <&funnel_in5>;
				};
			};
		};
	};
};
#include "qcom-apq8064-pins.dtsi"