[SCSI] qla2xxx: Prep zero-length BSG data-transfer requests.
During command failure/non-recognition, the upper-layer
FC-transport expects the drivers to set
job-reply->reply_payload_rcv_len. Do this in a consistent manner
to avoid duplication.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/qla2xxx/qla_bsg.c b/drivers/scsi/qla2xxx/qla_bsg.c
index b2b6644..0207143 100644
--- a/drivers/scsi/qla2xxx/qla_bsg.c
+++ b/drivers/scsi/qla2xxx/qla_bsg.c
@@ -108,8 +108,6 @@
uint32_t len;
uint32_t oper;
- bsg_job->reply->reply_payload_rcv_len = 0;
-
if (!(IS_QLA24XX_TYPE(ha) || IS_QLA25XX(ha) || IS_QLA82XX(ha))) {
ret = -EINVAL;
goto exit_fcp_prio_cfg;
@@ -729,7 +727,6 @@
if (qla81xx_get_port_config(vha, config)) {
ql_log(ql_log_warn, vha, 0x701f,
"Get port config failed.\n");
- bsg_job->reply->reply_payload_rcv_len = 0;
bsg_job->reply->result = (DID_ERROR << 16);
rval = -EPERM;
goto done_free_dma_req;
@@ -743,8 +740,6 @@
new_config)) {
ql_log(ql_log_warn, vha, 0x7024,
"Internal loopback failed.\n");
- bsg_job->reply->reply_payload_rcv_len =
- 0;
bsg_job->reply->result =
(DID_ERROR << 16);
rval = -EPERM;
@@ -756,8 +751,6 @@
*/
if (qla81xx_reset_internal_loopback(vha,
config, 1)) {
- bsg_job->reply->reply_payload_rcv_len =
- 0;
bsg_job->reply->result =
(DID_ERROR << 16);
rval = -EPERM;
@@ -794,7 +787,6 @@
"MPI reset failed.\n");
}
- bsg_job->reply->reply_payload_rcv_len = 0;
bsg_job->reply->result = (DID_ERROR << 16);
rval = -EIO;
goto done_free_dma_req;
@@ -819,7 +811,6 @@
fw_sts_ptr += sizeof(response);
*fw_sts_ptr = command_sent;
rval = 0;
- bsg_job->reply->reply_payload_rcv_len = 0;
bsg_job->reply->result = (DID_ERROR << 16);
} else {
ql_dbg(ql_dbg_user, vha, 0x702d,
@@ -878,7 +869,7 @@
if (rval) {
ql_log(ql_log_warn, vha, 0x7030,
"Vendor request 84xx reset failed.\n");
- rval = bsg_job->reply->reply_payload_rcv_len = 0;
+ rval = 0;
bsg_job->reply->result = (DID_ERROR << 16);
} else {
@@ -977,9 +968,8 @@
ql_log(ql_log_warn, vha, 0x7037,
"Vendor request 84xx updatefw failed.\n");
- rval = bsg_job->reply->reply_payload_rcv_len = 0;
+ rval = 0;
bsg_job->reply->result = (DID_ERROR << 16);
-
} else {
ql_dbg(ql_dbg_user, vha, 0x7038,
"Vendor request 84xx updatefw completed.\n");
@@ -1165,7 +1155,7 @@
ql_log(ql_log_warn, vha, 0x7043,
"Vendor request 84xx mgmt failed.\n");
- rval = bsg_job->reply->reply_payload_rcv_len = 0;
+ rval = 0;
bsg_job->reply->result = (DID_ERROR << 16);
} else {
@@ -1216,8 +1206,6 @@
uint16_t mb[MAILBOX_REGISTER_COUNT];
uint8_t *rsp_ptr = NULL;
- bsg_job->reply->reply_payload_rcv_len = 0;
-
if (!IS_IIDMA_CAPABLE(vha->hw)) {
ql_log(ql_log_info, vha, 0x7046, "iiDMA not supported.\n");
return -EINVAL;
@@ -1310,8 +1298,6 @@
int valid = 0;
struct qla_hw_data *ha = vha->hw;
- bsg_job->reply->reply_payload_rcv_len = 0;
-
if (unlikely(pci_channel_offline(ha->pdev)))
return -EINVAL;
@@ -1623,6 +1609,9 @@
struct Scsi_Host *host;
scsi_qla_host_t *vha;
+ /* In case no data transferred. */
+ bsg_job->reply->reply_payload_rcv_len = 0;
+
if (bsg_job->request->msgcode == FC_BSG_RPT_ELS) {
rport = bsg_job->rport;
fcport = *(fc_port_t **) rport->dd_data;
@@ -1661,6 +1650,7 @@
case FC_BSG_RPT_CT:
default:
ql_log(ql_log_warn, vha, 0x705a, "Unsupported BSG request.\n");
+ bsg_job->reply->result = ret;
break;
}
return ret;
