regulator: cleanup comments
For spdx
Remove leading space, add space after //
Replacements
overriden to overridden
Calulate to Calculate
addional to additional
regulatior to regulator
devive to device
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220305162438.689442-1-trix@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c
index 80b65cb..cb7e500 100644
--- a/drivers/regulator/max8973-regulator.c
+++ b/drivers/regulator/max8973-regulator.c
@@ -459,7 +459,7 @@ static int max8973_thermal_read_temp(void *data, int *temp)
return ret;
}
- /* +1 degC to trigger cool devive */
+ /* +1 degC to trigger cool device */
if (val & MAX77621_CHIPID_TJINT_S)
*temp = mchip->junction_temp_warning + 1000;
else
diff --git a/drivers/regulator/sc2731-regulator.c b/drivers/regulator/sc2731-regulator.c
index 0f21f95..71e5ceb 100644
--- a/drivers/regulator/sc2731-regulator.c
+++ b/drivers/regulator/sc2731-regulator.c
@@ -1,4 +1,4 @@
- //SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2017 Spreadtrum Communications Inc.
*/
diff --git a/drivers/regulator/ti-abb-regulator.c b/drivers/regulator/ti-abb-regulator.c
index 2931a0b..bd7b2f2 100644
--- a/drivers/regulator/ti-abb-regulator.c
+++ b/drivers/regulator/ti-abb-regulator.c
@@ -42,7 +42,7 @@
/**
* struct ti_abb_info - ABB information per voltage setting
* @opp_sel: one of TI_ABB macro
- * @vset: (optional) vset value that LDOVBB needs to be overriden with.
+ * @vset: (optional) vset value that LDOVBB needs to be overridden with.
*
* Array of per voltage entries organized in the same order as regulator_desc's
* volt_table list. (selector is used to index from this array)
@@ -484,7 +484,7 @@ static int ti_abb_init_timings(struct device *dev, struct ti_abb *abb)
/* Calculate cycle rate */
cycle_rate = DIV_ROUND_CLOSEST(clock_cycles * 10, clk_rate);
- /* Calulate SR2_WTCNT_VALUE */
+ /* Calculate SR2_WTCNT_VALUE */
sr2_wt_cnt_val = DIV_ROUND_CLOSEST(abb->settling_time * 10, cycle_rate);
dev_dbg(dev, "%s: Clk_rate=%ld, sr2_cnt=0x%08x\n", __func__,
@@ -688,7 +688,7 @@ MODULE_DEVICE_TABLE(of, ti_abb_of_match);
* @pdev: ABB platform device
*
* Initializes an individual ABB LDO for required Body-Bias. ABB is used to
- * addional bias supply to SoC modules for power savings or mandatory stability
+ * additional bias supply to SoC modules for power savings or mandatory stability
* configuration at certain Operating Performance Points(OPPs).
*
* Return: 0 on success or appropriate error value when fails
diff --git a/drivers/regulator/wm8350-regulator.c b/drivers/regulator/wm8350-regulator.c
index 6579bfd..b1d5aac 100644
--- a/drivers/regulator/wm8350-regulator.c
+++ b/drivers/regulator/wm8350-regulator.c
@@ -1112,7 +1112,7 @@ static int wm8350_regulator_probe(struct platform_device *pdev)
if (pdev->id < WM8350_DCDC_1 || pdev->id > WM8350_ISINK_B)
return -ENODEV;
- /* do any regulatior specific init */
+ /* do any regulator specific init */
switch (pdev->id) {
case WM8350_DCDC_1:
val = wm8350_reg_read(wm8350, WM8350_DCDC1_LOW_POWER);
