Merge branch 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: normal_i2c arrays should be const
hwmon: New driver for Analog Devices ADT7473 sensor chip
hwmon: (coretemp) Add Penryn CPU to coretemp
hwmon: (coretemp) Add TjMax detection for mobile CPUs
hwmon: (applesmc) sensors set for MacBook2
hwmon: (thmc50) Storage class should be before const qualifier
hwmon: (coretemp) fix section mismatch warning
hwmon: (coretemp) Add maximum cooling temperature readout
hwmon: (adm1026) Properly terminate sysfs groups
hwmon: (vt8231) Update maintainer email address
hwmon: (vt8231) Add individual alarm files
hwmon: (via686a) Add individual alarm files
hwmon: (smsc47m1) Add individual alarm files
hwmon: (max1619) Add individual alarm and fault files
hwmon: (lm92) Add individual alarm files
diff --git a/Documentation/hwmon/adt7473 b/Documentation/hwmon/adt7473
new file mode 100644
index 0000000..22d8b19
--- /dev/null
+++ b/Documentation/hwmon/adt7473
@@ -0,0 +1,79 @@
+Kernel driver adt7473
+======================
+
+Supported chips:
+ * Analog Devices ADT7473
+ Prefix: 'adt7473'
+ Addresses scanned: I2C 0x2C, 0x2D, 0x2E
+ Datasheet: Publicly available at the Analog Devices website
+
+Author: Darrick J. Wong
+
+Description
+-----------
+
+This driver implements support for the Analog Devices ADT7473 chip family.
+
+The LM85 uses the 2-wire interface compatible with the SMBUS 2.0
+specification. Using an analog to digital converter it measures three (3)
+temperatures and two (2) voltages. It has three (3) 16-bit counters for
+measuring fan speed. There are three (3) PWM outputs that can be used
+to control fan speed.
+
+A sophisticated control system for the PWM outputs is designed into the
+LM85 that allows fan speed to be adjusted automatically based on any of the
+three temperature sensors. Each PWM output is individually adjustable and
+programmable. Once configured, the ADT7473 will adjust the PWM outputs in
+response to the measured temperatures without further host intervention.
+This feature can also be disabled for manual control of the PWM's.
+
+Each of the measured inputs (voltage, temperature, fan speed) has
+corresponding high/low limit values. The ADT7473 will signal an ALARM if
+any measured value exceeds either limit.
+
+The ADT7473 samples all inputs continuously. The driver will not read
+the registers more often than once every other second. Further,
+configuration data is only read once per minute.
+
+Special Features
+----------------
+
+The ADT7473 have a 10-bit ADC and can therefore measure temperatures
+with 0.25 degC resolution. Temperature readings can be configured either
+for twos complement format or "Offset 64" format, wherein 63 is subtracted
+from the raw value to get the temperature value.
+
+The Analog Devices datasheet is very detailed and describes a procedure for
+determining an optimal configuration for the automatic PWM control.
+
+Hardware Configurations
+-----------------------
+
+The ADT7473 chips have an optional SMBALERT output that can be used to
+signal the chipset in case a limit is exceeded or the temperature sensors
+fail. Individual sensor interrupts can be masked so they won't trigger
+SMBALERT. The SMBALERT output if configured replaces the PWM2 function.
+
+Configuration Notes
+-------------------
+
+Besides standard interfaces driver adds the following:
+
+* PWM Control
+
+* pwm#_auto_point1_pwm and pwm#_auto_point1_temp and
+* pwm#_auto_point2_pwm and pwm#_auto_point2_temp -
+
+point1: Set the pwm speed at a lower temperature bound.
+point2: Set the pwm speed at a higher temperature bound.
+
+The ADT7473 will scale the pwm between the lower and higher pwm speed when
+the temperature is between the two temperature boundaries. PWM values range
+from 0 (off) to 255 (full speed).
+
+Notes
+-----
+
+The NVIDIA binary driver presents an ADT7473 chip via an on-card i2c bus.
+Unfortunately, they fail to set the i2c adapter class, so this driver may
+fail to find the chip until the nvidia driver is patched.
diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp
index 170bf86..dbbe6c70 100644
--- a/Documentation/hwmon/coretemp
+++ b/Documentation/hwmon/coretemp
@@ -4,9 +4,10 @@
Supported chips:
* All Intel Core family
Prefix: 'coretemp'
- CPUID: family 0x6, models 0xe, 0xf, 0x16
+ CPUID: family 0x6, models 0xe, 0xf, 0x16, 0x17
Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual
Volume 3A: System Programming Guide
+ http://softwarecommunity.intel.com/Wiki/Mobility/720.htm
Author: Rudolf Marek
@@ -25,7 +26,8 @@
the Out-Of-Spec bit. Following table summarizes the exported sysfs files:
temp1_input - Core temperature (in millidegrees Celsius).
-temp1_crit - Maximum junction temperature (in millidegrees Celsius).
+temp1_max - All cooling devices should be turned on (on Core2).
+temp1_crit - Maximum junction temperature (in millidegrees Celsius).
temp1_crit_alarm - Set when Out-of-spec bit is set, never clears.
Correct CPU operation is no longer guaranteed.
temp1_label - Contains string "Core X", where X is processor
diff --git a/MAINTAINERS b/MAINTAINERS
index fd81e06..962babe 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4261,7 +4261,7 @@
VT8231 HARDWARE MONITOR DRIVER
P: Roger Lucas
-M: roger@planbit.co.uk
+M: vt8231@hiddenengine.co.uk
L: lm-sensors@lm-sensors.org
S: Maintained
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 410ffe4..368879f 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -143,6 +143,16 @@
This driver can also be built as a module. If so, the module
will be called adt7470.
+config SENSORS_ADT7473
+ tristate "Analog Devices ADT7473"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ ADT7473 temperature monitoring chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called adt7473.
+
config SENSORS_K8TEMP
tristate "AMD Athlon64/FX or Opteron temperature sensor"
depends on X86 && PCI && EXPERIMENTAL
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 8241613..3bdb05a 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -24,6 +24,7 @@
obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o
obj-$(CONFIG_SENSORS_ADS7828) += ads7828.o
obj-$(CONFIG_SENSORS_ADT7470) += adt7470.o
+obj-$(CONFIG_SENSORS_ADT7473) += adt7473.o
obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o
obj-$(CONFIG_SENSORS_AMS) += ams/
obj-$(CONFIG_SENSORS_ATXP1) += atxp1.o
diff --git a/drivers/hwmon/ad7418.c b/drivers/hwmon/ad7418.c
index fcd7fe7..466b9ee 100644
--- a/drivers/hwmon/ad7418.c
+++ b/drivers/hwmon/ad7418.c
@@ -26,7 +26,7 @@
#define DRV_VERSION "0.3"
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x28, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x28, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_3(ad7416, ad7417, ad7418);
diff --git a/drivers/hwmon/adm1021.c b/drivers/hwmon/adm1021.c
index b96be77..ecbf694 100644
--- a/drivers/hwmon/adm1021.c
+++ b/drivers/hwmon/adm1021.c
@@ -31,10 +31,8 @@
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a,
- 0x29, 0x2a, 0x2b,
- 0x4c, 0x4d, 0x4e,
- I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = {
+ 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_8(adm1021, adm1023, max1617, max1617a, thmc10, lm84, gl523sm,
diff --git a/drivers/hwmon/adm1025.c b/drivers/hwmon/adm1025.c
index e96c372..1d76de7 100644
--- a/drivers/hwmon/adm1025.c
+++ b/drivers/hwmon/adm1025.c
@@ -62,7 +62,7 @@
* NE1619 has two possible addresses: 0x2c and 0x2d.
*/
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/adm1026.c b/drivers/hwmon/adm1026.c
index 8002f68..904c6ce 100644
--- a/drivers/hwmon/adm1026.c
+++ b/drivers/hwmon/adm1026.c
@@ -35,7 +35,7 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(adm1026);
@@ -1624,6 +1624,7 @@
&dev_attr_temp3_crit_enable.attr,
&dev_attr_temp3_auto_point1_pwm.attr,
&dev_attr_temp3_auto_point2_pwm.attr,
+ NULL
};
static const struct attribute_group adm1026_group_temp3 = {
@@ -1639,6 +1640,7 @@
&sensor_dev_attr_in9_max.dev_attr.attr,
&sensor_dev_attr_in9_min.dev_attr.attr,
&sensor_dev_attr_in9_alarm.dev_attr.attr,
+ NULL
};
static const struct attribute_group adm1026_group_in8_9 = {
diff --git a/drivers/hwmon/adm1029.c b/drivers/hwmon/adm1029.c
index 0bc897d..2c6608d 100644
--- a/drivers/hwmon/adm1029.c
+++ b/drivers/hwmon/adm1029.c
@@ -39,10 +39,8 @@
* Addresses to scan
*/
-static unsigned short normal_i2c[] = {
- 0x28, 0x29, 0x2a,
- 0x2b, 0x2c, 0x2d,
- 0x2e, 0x2f, I2C_CLIENT_END
+static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d,
+ 0x2e, 0x2f, I2C_CLIENT_END
};
/*
diff --git a/drivers/hwmon/adm1031.c b/drivers/hwmon/adm1031.c
index 5aaad36..2bffcab 100644
--- a/drivers/hwmon/adm1031.c
+++ b/drivers/hwmon/adm1031.c
@@ -61,7 +61,7 @@
#define ADM1031_CONF2_TEMP_ENABLE(chan) (0x10 << (chan))
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_2(adm1030, adm1031);
diff --git a/drivers/hwmon/adm9240.c b/drivers/hwmon/adm9240.c
index 7671d2b..149ef25 100644
--- a/drivers/hwmon/adm9240.c
+++ b/drivers/hwmon/adm9240.c
@@ -52,7 +52,7 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
I2C_CLIENT_END };
/* Insmod parameters */
diff --git a/drivers/hwmon/ads7828.c b/drivers/hwmon/ads7828.c
index 6b8a73e..ed71a8b 100644
--- a/drivers/hwmon/ads7828.c
+++ b/drivers/hwmon/ads7828.c
@@ -44,7 +44,7 @@
#define ADS7828_INT_VREF_MV 2500 /* Internal vref is 2.5V, 2500mV */
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
+static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
I2C_CLIENT_END };
/* Insmod parameters */
diff --git a/drivers/hwmon/adt7470.c b/drivers/hwmon/adt7470.c
index 747693a..6b5325f 100644
--- a/drivers/hwmon/adt7470.c
+++ b/drivers/hwmon/adt7470.c
@@ -30,7 +30,7 @@
#include <linux/log2.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2C, 0x2E, 0x2F, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2C, 0x2E, 0x2F, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(adt7470);
diff --git a/drivers/hwmon/adt7473.c b/drivers/hwmon/adt7473.c
new file mode 100644
index 0000000..9587869
--- /dev/null
+++ b/drivers/hwmon/adt7473.c
@@ -0,0 +1,1157 @@
+/*
+ * A hwmon driver for the Analog Devices ADT7473
+ * Copyright (C) 2007 IBM
+ *
+ * Author: Darrick J. Wong <djwong@us.ibm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+#include <linux/log2.h>
+
+/* Addresses to scan */
+static const unsigned short normal_i2c[] = { 0x2C, 0x2D, 0x2E, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(adt7473);
+
+/* ADT7473 registers */
+#define ADT7473_REG_BASE_ADDR 0x20
+
+#define ADT7473_REG_VOLT_BASE_ADDR 0x21
+#define ADT7473_REG_VOLT_MAX_ADDR 0x22
+#define ADT7473_REG_VOLT_MIN_BASE_ADDR 0x46
+#define ADT7473_REG_VOLT_MIN_MAX_ADDR 0x49
+
+#define ADT7473_REG_TEMP_BASE_ADDR 0x25
+#define ADT7473_REG_TEMP_MAX_ADDR 0x27
+#define ADT7473_REG_TEMP_LIMITS_BASE_ADDR 0x4E
+#define ADT7473_REG_TEMP_LIMITS_MAX_ADDR 0x53
+#define ADT7473_REG_TEMP_TMIN_BASE_ADDR 0x67
+#define ADT7473_REG_TEMP_TMIN_MAX_ADDR 0x69
+#define ADT7473_REG_TEMP_TMAX_BASE_ADDR 0x6A
+#define ADT7473_REG_TEMP_TMAX_MAX_ADDR 0x6C
+
+#define ADT7473_REG_FAN_BASE_ADDR 0x28
+#define ADT7473_REG_FAN_MAX_ADDR 0x2F
+#define ADT7473_REG_FAN_MIN_BASE_ADDR 0x54
+#define ADT7473_REG_FAN_MIN_MAX_ADDR 0x5B
+
+#define ADT7473_REG_PWM_BASE_ADDR 0x30
+#define ADT7473_REG_PWM_MAX_ADDR 0x32
+#define ADT7473_REG_PWM_MIN_BASE_ADDR 0x64
+#define ADT7473_REG_PWM_MIN_MAX_ADDR 0x66
+#define ADT7473_REG_PWM_MAX_BASE_ADDR 0x38
+#define ADT7473_REG_PWM_MAX_MAX_ADDR 0x3A
+#define ADT7473_REG_PWM_BHVR_BASE_ADDR 0x5C
+#define ADT7473_REG_PWM_BHVR_MAX_ADDR 0x5E
+#define ADT7473_PWM_BHVR_MASK 0xE0
+#define ADT7473_PWM_BHVR_SHIFT 5
+
+#define ADT7473_REG_CFG1 0x40
+#define ADT7473_CFG1_START 0x01
+#define ADT7473_CFG1_READY 0x04
+#define ADT7473_REG_CFG2 0x73
+#define ADT7473_REG_CFG3 0x78
+#define ADT7473_REG_CFG4 0x7D
+#define ADT7473_CFG4_MAX_DUTY_AT_OVT 0x08
+#define ADT7473_REG_CFG5 0x7C
+#define ADT7473_CFG5_TEMP_TWOS 0x01
+#define ADT7473_CFG5_TEMP_OFFSET 0x02
+
+#define ADT7473_REG_DEVICE 0x3D
+#define ADT7473_VENDOR 0x41
+#define ADT7473_REG_VENDOR 0x3E
+#define ADT7473_DEVICE 0x73
+#define ADT7473_REG_REVISION 0x3F
+#define ADT7473_REV_68 0x68
+#define ADT7473_REV_69 0x69
+
+#define ADT7473_REG_ALARM1 0x41
+#define ADT7473_VCCP_ALARM 0x02
+#define ADT7473_VCC_ALARM 0x04
+#define ADT7473_R1T_ALARM 0x10
+#define ADT7473_LT_ALARM 0x20
+#define ADT7473_R2T_ALARM 0x40
+#define ADT7473_OOL 0x80
+#define ADT7473_REG_ALARM2 0x42
+#define ADT7473_OVT_ALARM 0x02
+#define ADT7473_FAN1_ALARM 0x04
+#define ADT7473_FAN2_ALARM 0x08
+#define ADT7473_FAN3_ALARM 0x10
+#define ADT7473_FAN4_ALARM 0x20
+#define ADT7473_R1T_SHORT 0x40
+#define ADT7473_R2T_SHORT 0x80
+#define ADT7473_REG_MAX_ADDR 0x80
+
+#define ALARM2(x) ((x) << 8)
+
+#define ADT7473_VOLT_COUNT 2
+#define ADT7473_REG_VOLT(x) (ADT7473_REG_VOLT_BASE_ADDR + (x))
+#define ADT7473_REG_VOLT_MIN(x) (ADT7473_REG_VOLT_MIN_BASE_ADDR + ((x) * 2))
+#define ADT7473_REG_VOLT_MAX(x) (ADT7473_REG_VOLT_MIN_BASE_ADDR + \
+ ((x) * 2) + 1)
+
+#define ADT7473_TEMP_COUNT 3
+#define ADT7473_REG_TEMP(x) (ADT7473_REG_TEMP_BASE_ADDR + (x))
+#define ADT7473_REG_TEMP_MIN(x) (ADT7473_REG_TEMP_LIMITS_BASE_ADDR + ((x) * 2))
+#define ADT7473_REG_TEMP_MAX(x) (ADT7473_REG_TEMP_LIMITS_BASE_ADDR + \
+ ((x) * 2) + 1)
+#define ADT7473_REG_TEMP_TMIN(x) (ADT7473_REG_TEMP_TMIN_BASE_ADDR + (x))
+#define ADT7473_REG_TEMP_TMAX(x) (ADT7473_REG_TEMP_TMAX_BASE_ADDR + (x))
+
+#define ADT7473_FAN_COUNT 4
+#define ADT7473_REG_FAN(x) (ADT7473_REG_FAN_BASE_ADDR + ((x) * 2))
+#define ADT7473_REG_FAN_MIN(x) (ADT7473_REG_FAN_MIN_BASE_ADDR + ((x) * 2))
+
+#define ADT7473_PWM_COUNT 3
+#define ADT7473_REG_PWM(x) (ADT7473_REG_PWM_BASE_ADDR + (x))
+#define ADT7473_REG_PWM_MAX(x) (ADT7473_REG_PWM_MAX_BASE_ADDR + (x))
+#define ADT7473_REG_PWM_MIN(x) (ADT7473_REG_PWM_MIN_BASE_ADDR + (x))
+#define ADT7473_REG_PWM_BHVR(x) (ADT7473_REG_PWM_BHVR_BASE_ADDR + (x))
+
+/* How often do we reread sensors values? (In jiffies) */
+#define SENSOR_REFRESH_INTERVAL (2 * HZ)
+
+/* How often do we reread sensor limit values? (In jiffies) */
+#define LIMIT_REFRESH_INTERVAL (60 * HZ)
+
+/* datasheet says to divide this number by the fan reading to get fan rpm */
+#define FAN_PERIOD_TO_RPM(x) ((90000 * 60) / (x))
+#define FAN_RPM_TO_PERIOD FAN_PERIOD_TO_RPM
+#define FAN_PERIOD_INVALID 65535
+#define FAN_DATA_VALID(x) ((x) && (x) != FAN_PERIOD_INVALID)
+
+struct adt7473_data {
+ struct i2c_client client;
+ struct device *hwmon_dev;
+ struct attribute_group attrs;
+ struct mutex lock;
+ char sensors_valid;
+ char limits_valid;
+ unsigned long sensors_last_updated; /* In jiffies */
+ unsigned long limits_last_updated; /* In jiffies */
+
+ u8 volt[ADT7473_VOLT_COUNT];
+ s8 volt_min[ADT7473_VOLT_COUNT];
+ s8 volt_max[ADT7473_VOLT_COUNT];
+
+ s8 temp[ADT7473_TEMP_COUNT];
+ s8 temp_min[ADT7473_TEMP_COUNT];
+ s8 temp_max[ADT7473_TEMP_COUNT];
+ s8 temp_tmin[ADT7473_TEMP_COUNT];
+ /* This is called the !THERM limit in the datasheet */
+ s8 temp_tmax[ADT7473_TEMP_COUNT];
+
+ u16 fan[ADT7473_FAN_COUNT];
+ u16 fan_min[ADT7473_FAN_COUNT];
+
+ u8 pwm[ADT7473_PWM_COUNT];
+ u8 pwm_max[ADT7473_PWM_COUNT];
+ u8 pwm_min[ADT7473_PWM_COUNT];
+ u8 pwm_behavior[ADT7473_PWM_COUNT];
+
+ u8 temp_twos_complement;
+ u8 temp_offset;
+
+ u16 alarm;
+ u8 max_duty_at_overheat;
+};
+
+static int adt7473_attach_adapter(struct i2c_adapter *adapter);
+static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind);
+static int adt7473_detach_client(struct i2c_client *client);
+
+static struct i2c_driver adt7473_driver = {
+ .driver = {
+ .name = "adt7473",
+ },
+ .attach_adapter = adt7473_attach_adapter,
+ .detach_client = adt7473_detach_client,
+};
+
+/*
+ * 16-bit registers on the ADT7473 are low-byte first. The data sheet says
+ * that the low byte must be read before the high byte.
+ */
+static inline int adt7473_read_word_data(struct i2c_client *client, u8 reg)
+{
+ u16 foo;
+ foo = i2c_smbus_read_byte_data(client, reg);
+ foo |= ((u16)i2c_smbus_read_byte_data(client, reg + 1) << 8);
+ return foo;
+}
+
+static inline int adt7473_write_word_data(struct i2c_client *client, u8 reg,
+ u16 value)
+{
+ return i2c_smbus_write_byte_data(client, reg, value & 0xFF)
+ && i2c_smbus_write_byte_data(client, reg + 1, value >> 8);
+}
+
+static void adt7473_init_client(struct i2c_client *client)
+{
+ int reg = i2c_smbus_read_byte_data(client, ADT7473_REG_CFG1);
+
+ if (!(reg & ADT7473_CFG1_READY)) {
+ dev_err(&client->dev, "Chip not ready.\n");
+ } else {
+ /* start monitoring */
+ i2c_smbus_write_byte_data(client, ADT7473_REG_CFG1,
+ reg | ADT7473_CFG1_START);
+ }
+}
+
+static struct adt7473_data *adt7473_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ unsigned long local_jiffies = jiffies;
+ u8 cfg;
+ int i;
+
+ mutex_lock(&data->lock);
+ if (time_before(local_jiffies, data->sensors_last_updated +
+ SENSOR_REFRESH_INTERVAL)
+ && data->sensors_valid)
+ goto no_sensor_update;
+
+ for (i = 0; i < ADT7473_VOLT_COUNT; i++)
+ data->volt[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_VOLT(i));
+
+ /* Determine temperature encoding */
+ cfg = i2c_smbus_read_byte_data(client, ADT7473_REG_CFG5);
+ data->temp_twos_complement = (cfg & ADT7473_CFG5_TEMP_TWOS);
+
+ /*
+ * What does this do? it implies a variable temperature sensor
+ * offset, but the datasheet doesn't say anything about this bit
+ * and other parts of the datasheet imply that "offset64" mode
+ * means that you shift temp values by -64 if the above bit was set.
+ */
+ data->temp_offset = (cfg & ADT7473_CFG5_TEMP_OFFSET);
+
+ for (i = 0; i < ADT7473_TEMP_COUNT; i++)
+ data->temp[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_TEMP(i));
+
+ for (i = 0; i < ADT7473_FAN_COUNT; i++)
+ data->fan[i] = adt7473_read_word_data(client,
+ ADT7473_REG_FAN(i));
+
+ for (i = 0; i < ADT7473_PWM_COUNT; i++)
+ data->pwm[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_PWM(i));
+
+ data->alarm = i2c_smbus_read_byte_data(client, ADT7473_REG_ALARM1);
+ if (data->alarm & ADT7473_OOL)
+ data->alarm |= ALARM2(i2c_smbus_read_byte_data(client,
+ ADT7473_REG_ALARM2));
+
+ data->sensors_last_updated = local_jiffies;
+ data->sensors_valid = 1;
+
+no_sensor_update:
+ if (time_before(local_jiffies, data->limits_last_updated +
+ LIMIT_REFRESH_INTERVAL)
+ && data->limits_valid)
+ goto out;
+
+ for (i = 0; i < ADT7473_VOLT_COUNT; i++) {
+ data->volt_min[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_VOLT_MIN(i));
+ data->volt_max[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_VOLT_MAX(i));
+ }
+
+ for (i = 0; i < ADT7473_TEMP_COUNT; i++) {
+ data->temp_min[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_TEMP_MIN(i));
+ data->temp_max[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_TEMP_MAX(i));
+ data->temp_tmin[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_TEMP_TMIN(i));
+ data->temp_tmax[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_TEMP_TMAX(i));
+ }
+
+ for (i = 0; i < ADT7473_FAN_COUNT; i++)
+ data->fan_min[i] = adt7473_read_word_data(client,
+ ADT7473_REG_FAN_MIN(i));
+
+ for (i = 0; i < ADT7473_PWM_COUNT; i++) {
+ data->pwm_max[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_PWM_MAX(i));
+ data->pwm_min[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_PWM_MIN(i));
+ data->pwm_behavior[i] = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_PWM_BHVR(i));
+ }
+
+ data->limits_last_updated = local_jiffies;
+ data->limits_valid = 1;
+
+out:
+ mutex_unlock(&data->lock);
+ return data;
+}
+
+/*
+ * On this chip, voltages are given as a count of steps between a minimum
+ * and maximum voltage, not a direct voltage.
+ */
+static const int volt_convert_table[][2] = {
+ {2997, 3},
+ {4395, 4},
+};
+
+static int decode_volt(int volt_index, u8 raw)
+{
+ int cmax = volt_convert_table[volt_index][0];
+ int cmin = volt_convert_table[volt_index][1];
+ return ((raw * (cmax - cmin)) / 255) + cmin;
+}
+
+static u8 encode_volt(int volt_index, int cooked)
+{
+ int cmax = volt_convert_table[volt_index][0];
+ int cmin = volt_convert_table[volt_index][1];
+ u8 x;
+
+ if (cooked > cmax)
+ cooked = cmax;
+ else if (cooked < cmin)
+ cooked = cmin;
+
+ x = ((cooked - cmin) * 255) / (cmax - cmin);
+
+ return x;
+}
+
+static ssize_t show_volt_min(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n",
+ decode_volt(attr->index, data->volt_min[attr->index]));
+}
+
+static ssize_t set_volt_min(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int volt = encode_volt(attr->index, simple_strtol(buf, NULL, 10));
+
+ mutex_lock(&data->lock);
+ data->volt_min[attr->index] = volt;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_VOLT_MIN(attr->index),
+ volt);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_volt_max(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n",
+ decode_volt(attr->index, data->volt_max[attr->index]));
+}
+
+static ssize_t set_volt_max(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int volt = encode_volt(attr->index, simple_strtol(buf, NULL, 10));
+
+ mutex_lock(&data->lock);
+ data->volt_max[attr->index] = volt;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_VOLT_MAX(attr->index),
+ volt);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_volt(struct device *dev, struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+
+ return sprintf(buf, "%d\n",
+ decode_volt(attr->index, data->volt[attr->index]));
+}
+
+/*
+ * This chip can report temperature data either as a two's complement
+ * number in the range -128 to 127, or as an unsigned number that must
+ * be offset by 64.
+ */
+static int decode_temp(struct adt7473_data *data, u8 raw)
+{
+ if (data->temp_twos_complement)
+ return (s8)raw;
+ return raw - 64;
+}
+
+static u8 encode_temp(struct adt7473_data *data, int cooked)
+{
+ if (data->temp_twos_complement)
+ return (cooked & 0xFF);
+ return cooked + 64;
+}
+
+static ssize_t show_temp_min(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n",
+ 1000 * decode_temp(data, data->temp_min[attr->index]));
+}
+
+static ssize_t set_temp_min(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10) / 1000;
+ temp = encode_temp(data, temp);
+
+ mutex_lock(&data->lock);
+ data->temp_min[attr->index] = temp;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_MIN(attr->index),
+ temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_temp_max(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n",
+ 1000 * decode_temp(data, data->temp_max[attr->index]));
+}
+
+static ssize_t set_temp_max(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10) / 1000;
+ temp = encode_temp(data, temp);
+
+ mutex_lock(&data->lock);
+ data->temp_max[attr->index] = temp;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_MAX(attr->index),
+ temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_temp(struct device *dev, struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n",
+ 1000 * decode_temp(data, data->temp[attr->index]));
+}
+
+static ssize_t show_fan_min(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+
+ if (FAN_DATA_VALID(data->fan_min[attr->index]))
+ return sprintf(buf, "%d\n",
+ FAN_PERIOD_TO_RPM(data->fan_min[attr->index]));
+ else
+ return sprintf(buf, "0\n");
+}
+
+static ssize_t set_fan_min(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10);
+
+ if (!temp)
+ return -EINVAL;
+ temp = FAN_RPM_TO_PERIOD(temp);
+
+ mutex_lock(&data->lock);
+ data->fan_min[attr->index] = temp;
+ adt7473_write_word_data(client, ADT7473_REG_FAN_MIN(attr->index), temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_fan(struct device *dev, struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+
+ if (FAN_DATA_VALID(data->fan[attr->index]))
+ return sprintf(buf, "%d\n",
+ FAN_PERIOD_TO_RPM(data->fan[attr->index]));
+ else
+ return sprintf(buf, "0\n");
+}
+
+static ssize_t show_max_duty_at_crit(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n", data->max_duty_at_overheat);
+}
+
+static ssize_t set_max_duty_at_crit(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ u8 reg;
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10);
+ temp = temp && 0xFF;
+
+ mutex_lock(&data->lock);
+ data->max_duty_at_overheat = temp;
+ reg = i2c_smbus_read_byte_data(client, ADT7473_REG_CFG4);
+ if (temp)
+ reg |= ADT7473_CFG4_MAX_DUTY_AT_OVT;
+ else
+ reg &= ~ADT7473_CFG4_MAX_DUTY_AT_OVT;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_CFG4, reg);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_pwm(struct device *dev, struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n", data->pwm[attr->index]);
+}
+
+static ssize_t set_pwm(struct device *dev, struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10);
+
+ mutex_lock(&data->lock);
+ data->pwm[attr->index] = temp;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_PWM(attr->index), temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_pwm_max(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n", data->pwm_max[attr->index]);
+}
+
+static ssize_t set_pwm_max(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10);
+
+ mutex_lock(&data->lock);
+ data->pwm_max[attr->index] = temp;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_MAX(attr->index),
+ temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_pwm_min(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n", data->pwm_min[attr->index]);
+}
+
+static ssize_t set_pwm_min(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10);
+
+ mutex_lock(&data->lock);
+ data->pwm_min[attr->index] = temp;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_MIN(attr->index),
+ temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_temp_tmax(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n",
+ 1000 * decode_temp(data, data->temp_tmax[attr->index]));
+}
+
+static ssize_t set_temp_tmax(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10) / 1000;
+ temp = encode_temp(data, temp);
+
+ mutex_lock(&data->lock);
+ data->temp_tmax[attr->index] = temp;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_TMAX(attr->index),
+ temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_temp_tmin(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ return sprintf(buf, "%d\n",
+ 1000 * decode_temp(data, data->temp_tmin[attr->index]));
+}
+
+static ssize_t set_temp_tmin(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10) / 1000;
+ temp = encode_temp(data, temp);
+
+ mutex_lock(&data->lock);
+ data->temp_tmin[attr->index] = temp;
+ i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_TMIN(attr->index),
+ temp);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_pwm_enable(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+
+ switch (data->pwm_behavior[attr->index] >> ADT7473_PWM_BHVR_SHIFT) {
+ case 3:
+ return sprintf(buf, "0\n");
+ case 7:
+ return sprintf(buf, "1\n");
+ default:
+ return sprintf(buf, "2\n");
+ }
+}
+
+static ssize_t set_pwm_enable(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ u8 reg;
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10);
+
+ switch (temp) {
+ case 0:
+ temp = 3;
+ break;
+ case 1:
+ temp = 7;
+ break;
+ case 2:
+ /* Enter automatic mode with fans off */
+ temp = 4;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ mutex_lock(&data->lock);
+ reg = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_PWM_BHVR(attr->index));
+ reg = (temp << ADT7473_PWM_BHVR_SHIFT) |
+ (reg & ~ADT7473_PWM_BHVR_MASK);
+ i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_BHVR(attr->index),
+ reg);
+ data->pwm_behavior[attr->index] = reg;
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_pwm_auto_temp(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+ int bhvr = data->pwm_behavior[attr->index] >> ADT7473_PWM_BHVR_SHIFT;
+
+ switch (bhvr) {
+ case 3:
+ case 4:
+ case 7:
+ return sprintf(buf, "0\n");
+ case 0:
+ case 1:
+ case 5:
+ case 6:
+ return sprintf(buf, "%d\n", bhvr + 1);
+ case 2:
+ return sprintf(buf, "4\n");
+ }
+ /* shouldn't ever get here */
+ BUG();
+}
+
+static ssize_t set_pwm_auto_temp(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf,
+ size_t count)
+{
+ u8 reg;
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adt7473_data *data = i2c_get_clientdata(client);
+ int temp = simple_strtol(buf, NULL, 10);
+
+ switch (temp) {
+ case 1:
+ case 2:
+ case 6:
+ case 7:
+ temp--;
+ break;
+ case 0:
+ temp = 4;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ mutex_lock(&data->lock);
+ reg = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_PWM_BHVR(attr->index));
+ reg = (temp << ADT7473_PWM_BHVR_SHIFT) |
+ (reg & ~ADT7473_PWM_BHVR_MASK);
+ i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_BHVR(attr->index),
+ reg);
+ data->pwm_behavior[attr->index] = reg;
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_alarm(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct adt7473_data *data = adt7473_update_device(dev);
+
+ if (data->alarm & attr->index)
+ return sprintf(buf, "1\n");
+ else
+ return sprintf(buf, "0\n");
+}
+
+
+static SENSOR_DEVICE_ATTR(in1_max, S_IWUSR | S_IRUGO, show_volt_max,
+ set_volt_max, 0);
+static SENSOR_DEVICE_ATTR(in2_max, S_IWUSR | S_IRUGO, show_volt_max,
+ set_volt_max, 1);
+
+static SENSOR_DEVICE_ATTR(in1_min, S_IWUSR | S_IRUGO, show_volt_min,
+ set_volt_min, 0);
+static SENSOR_DEVICE_ATTR(in2_min, S_IWUSR | S_IRUGO, show_volt_min,
+ set_volt_min, 1);
+
+static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, show_volt, NULL, 0);
+static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, show_volt, NULL, 1);
+
+static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL,
+ ADT7473_VCCP_ALARM);
+static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL,
+ ADT7473_VCC_ALARM);
+
+static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp_max,
+ set_temp_max, 0);
+static SENSOR_DEVICE_ATTR(temp2_max, S_IWUSR | S_IRUGO, show_temp_max,
+ set_temp_max, 1);
+static SENSOR_DEVICE_ATTR(temp3_max, S_IWUSR | S_IRUGO, show_temp_max,
+ set_temp_max, 2);
+
+static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp_min,
+ set_temp_min, 0);
+static SENSOR_DEVICE_ATTR(temp2_min, S_IWUSR | S_IRUGO, show_temp_min,
+ set_temp_min, 1);
+static SENSOR_DEVICE_ATTR(temp3_min, S_IWUSR | S_IRUGO, show_temp_min,
+ set_temp_min, 2);
+
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 2);
+
+static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL,
+ ADT7473_R1T_ALARM | ALARM2(ADT7473_R1T_SHORT));
+static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL,
+ ADT7473_LT_ALARM);
+static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL,
+ ADT7473_R2T_ALARM | ALARM2(ADT7473_R2T_SHORT));
+
+static SENSOR_DEVICE_ATTR(fan1_min, S_IWUSR | S_IRUGO, show_fan_min,
+ set_fan_min, 0);
+static SENSOR_DEVICE_ATTR(fan2_min, S_IWUSR | S_IRUGO, show_fan_min,
+ set_fan_min, 1);
+static SENSOR_DEVICE_ATTR(fan3_min, S_IWUSR | S_IRUGO, show_fan_min,
+ set_fan_min, 2);
+static SENSOR_DEVICE_ATTR(fan4_min, S_IWUSR | S_IRUGO, show_fan_min,
+ set_fan_min, 3);
+
+static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 0);
+static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan, NULL, 1);
+static SENSOR_DEVICE_ATTR(fan3_input, S_IRUGO, show_fan, NULL, 2);
+static SENSOR_DEVICE_ATTR(fan4_input, S_IRUGO, show_fan, NULL, 3);
+
+static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL,
+ ALARM2(ADT7473_FAN1_ALARM));
+static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL,
+ ALARM2(ADT7473_FAN2_ALARM));
+static SENSOR_DEVICE_ATTR(fan3_alarm, S_IRUGO, show_alarm, NULL,
+ ALARM2(ADT7473_FAN3_ALARM));
+static SENSOR_DEVICE_ATTR(fan4_alarm, S_IRUGO, show_alarm, NULL,
+ ALARM2(ADT7473_FAN4_ALARM));
+
+static SENSOR_DEVICE_ATTR(pwm_use_point2_pwm_at_crit, S_IWUSR | S_IRUGO,
+ show_max_duty_at_crit, set_max_duty_at_crit, 0);
+
+static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 0);
+static SENSOR_DEVICE_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 1);
+static SENSOR_DEVICE_ATTR(pwm3, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 2);
+
+static SENSOR_DEVICE_ATTR(pwm1_auto_point1_pwm, S_IWUSR | S_IRUGO,
+ show_pwm_min, set_pwm_min, 0);
+static SENSOR_DEVICE_ATTR(pwm2_auto_point1_pwm, S_IWUSR | S_IRUGO,
+ show_pwm_min, set_pwm_min, 1);
+static SENSOR_DEVICE_ATTR(pwm3_auto_point1_pwm, S_IWUSR | S_IRUGO,
+ show_pwm_min, set_pwm_min, 2);
+
+static SENSOR_DEVICE_ATTR(pwm1_auto_point2_pwm, S_IWUSR | S_IRUGO,
+ show_pwm_max, set_pwm_max, 0);
+static SENSOR_DEVICE_ATTR(pwm2_auto_point2_pwm, S_IWUSR | S_IRUGO,
+ show_pwm_max, set_pwm_max, 1);
+static SENSOR_DEVICE_ATTR(pwm3_auto_point2_pwm, S_IWUSR | S_IRUGO,
+ show_pwm_max, set_pwm_max, 2);
+
+static SENSOR_DEVICE_ATTR(temp1_auto_point1_temp, S_IWUSR | S_IRUGO,
+ show_temp_tmin, set_temp_tmin, 0);
+static SENSOR_DEVICE_ATTR(temp2_auto_point1_temp, S_IWUSR | S_IRUGO,
+ show_temp_tmin, set_temp_tmin, 1);
+static SENSOR_DEVICE_ATTR(temp3_auto_point1_temp, S_IWUSR | S_IRUGO,
+ show_temp_tmin, set_temp_tmin, 2);
+
+static SENSOR_DEVICE_ATTR(temp1_auto_point2_temp, S_IWUSR | S_IRUGO,
+ show_temp_tmax, set_temp_tmax, 0);
+static SENSOR_DEVICE_ATTR(temp2_auto_point2_temp, S_IWUSR | S_IRUGO,
+ show_temp_tmax, set_temp_tmax, 1);
+static SENSOR_DEVICE_ATTR(temp3_auto_point2_temp, S_IWUSR | S_IRUGO,
+ show_temp_tmax, set_temp_tmax, 2);
+
+static SENSOR_DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO, show_pwm_enable,
+ set_pwm_enable, 0);
+static SENSOR_DEVICE_ATTR(pwm2_enable, S_IWUSR | S_IRUGO, show_pwm_enable,
+ set_pwm_enable, 1);
+static SENSOR_DEVICE_ATTR(pwm3_enable, S_IWUSR | S_IRUGO, show_pwm_enable,
+ set_pwm_enable, 2);
+
+static SENSOR_DEVICE_ATTR(pwm1_auto_channels_temp, S_IWUSR | S_IRUGO,
+ show_pwm_auto_temp, set_pwm_auto_temp, 0);
+static SENSOR_DEVICE_ATTR(pwm2_auto_channels_temp, S_IWUSR | S_IRUGO,
+ show_pwm_auto_temp, set_pwm_auto_temp, 1);
+static SENSOR_DEVICE_ATTR(pwm3_auto_channels_temp, S_IWUSR | S_IRUGO,
+ show_pwm_auto_temp, set_pwm_auto_temp, 2);
+
+static struct attribute *adt7473_attr[] =
+{
+ &sensor_dev_attr_in1_max.dev_attr.attr,
+ &sensor_dev_attr_in2_max.dev_attr.attr,
+ &sensor_dev_attr_in1_min.dev_attr.attr,
+ &sensor_dev_attr_in2_min.dev_attr.attr,
+ &sensor_dev_attr_in1_input.dev_attr.attr,
+ &sensor_dev_attr_in2_input.dev_attr.attr,
+ &sensor_dev_attr_in1_alarm.dev_attr.attr,
+ &sensor_dev_attr_in2_alarm.dev_attr.attr,
+
+ &sensor_dev_attr_temp1_max.dev_attr.attr,
+ &sensor_dev_attr_temp2_max.dev_attr.attr,
+ &sensor_dev_attr_temp3_max.dev_attr.attr,
+ &sensor_dev_attr_temp1_min.dev_attr.attr,
+ &sensor_dev_attr_temp2_min.dev_attr.attr,
+ &sensor_dev_attr_temp3_min.dev_attr.attr,
+ &sensor_dev_attr_temp1_input.dev_attr.attr,
+ &sensor_dev_attr_temp2_input.dev_attr.attr,
+ &sensor_dev_attr_temp3_input.dev_attr.attr,
+ &sensor_dev_attr_temp1_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp3_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_temp2_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_temp3_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_temp1_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_temp2_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_temp3_auto_point2_temp.dev_attr.attr,
+
+ &sensor_dev_attr_fan1_min.dev_attr.attr,
+ &sensor_dev_attr_fan2_min.dev_attr.attr,
+ &sensor_dev_attr_fan3_min.dev_attr.attr,
+ &sensor_dev_attr_fan4_min.dev_attr.attr,
+ &sensor_dev_attr_fan1_input.dev_attr.attr,
+ &sensor_dev_attr_fan2_input.dev_attr.attr,
+ &sensor_dev_attr_fan3_input.dev_attr.attr,
+ &sensor_dev_attr_fan4_input.dev_attr.attr,
+ &sensor_dev_attr_fan1_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan2_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan3_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan4_alarm.dev_attr.attr,
+
+ &sensor_dev_attr_pwm_use_point2_pwm_at_crit.dev_attr.attr,
+
+ &sensor_dev_attr_pwm1.dev_attr.attr,
+ &sensor_dev_attr_pwm2.dev_attr.attr,
+ &sensor_dev_attr_pwm3.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_point1_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_point1_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_point2_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_point2_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_point2_pwm.dev_attr.attr,
+
+ &sensor_dev_attr_pwm1_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm2_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm3_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_channels_temp.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_channels_temp.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_channels_temp.dev_attr.attr,
+
+ NULL
+};
+
+static int adt7473_attach_adapter(struct i2c_adapter *adapter)
+{
+ if (!(adapter->class & I2C_CLASS_HWMON))
+ return 0;
+ return i2c_probe(adapter, &addr_data, adt7473_detect);
+}
+
+static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind)
+{
+ struct i2c_client *client;
+ struct adt7473_data *data;
+ int err = 0;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+ goto exit;
+
+ data = kzalloc(sizeof(struct adt7473_data), GFP_KERNEL);
+ if (!data) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ client = &data->client;
+ client->addr = address;
+ client->adapter = adapter;
+ client->driver = &adt7473_driver;
+
+ i2c_set_clientdata(client, data);
+
+ mutex_init(&data->lock);
+
+ if (kind <= 0) {
+ int vendor, device, revision;
+
+ vendor = i2c_smbus_read_byte_data(client, ADT7473_REG_VENDOR);
+ if (vendor != ADT7473_VENDOR) {
+ err = -ENODEV;
+ goto exit_free;
+ }
+
+ device = i2c_smbus_read_byte_data(client, ADT7473_REG_DEVICE);
+ if (device != ADT7473_DEVICE) {
+ err = -ENODEV;
+ goto exit_free;
+ }
+
+ revision = i2c_smbus_read_byte_data(client,
+ ADT7473_REG_REVISION);
+ if (revision != ADT7473_REV_68 && revision != ADT7473_REV_69) {
+ err = -ENODEV;
+ goto exit_free;
+ }
+ } else
+ dev_dbg(&adapter->dev, "detection forced\n");
+
+ strlcpy(client->name, "adt7473", I2C_NAME_SIZE);
+
+ err = i2c_attach_client(client);
+ if (err)
+ goto exit_free;
+
+ dev_info(&client->dev, "%s chip found\n", client->name);
+
+ /* Initialize the ADT7473 chip */
+ adt7473_init_client(client);
+
+ /* Register sysfs hooks */
+ data->attrs.attrs = adt7473_attr;
+ err = sysfs_create_group(&client->dev.kobj, &data->attrs);
+ if (err)
+ goto exit_detach;
+
+ data->hwmon_dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ goto exit_remove;
+ }
+
+ return 0;
+
+exit_remove:
+ sysfs_remove_group(&client->dev.kobj, &data->attrs);
+exit_detach:
+ i2c_detach_client(client);
+exit_free:
+ kfree(data);
+exit:
+ return err;
+}
+
+static int adt7473_detach_client(struct i2c_client *client)
+{
+ struct adt7473_data *data = i2c_get_clientdata(client);
+
+ hwmon_device_unregister(data->hwmon_dev);
+ sysfs_remove_group(&client->dev.kobj, &data->attrs);
+ i2c_detach_client(client);
+ kfree(data);
+ return 0;
+}
+
+static int __init adt7473_init(void)
+{
+ return i2c_add_driver(&adt7473_driver);
+}
+
+static void __exit adt7473_exit(void)
+{
+ i2c_del_driver(&adt7473_driver);
+}
+
+MODULE_AUTHOR("Darrick J. Wong <djwong@us.ibm.com>");
+MODULE_DESCRIPTION("ADT7473 driver");
+MODULE_LICENSE("GPL");
+
+module_init(adt7473_init);
+module_exit(adt7473_exit);
diff --git a/drivers/hwmon/applesmc.c b/drivers/hwmon/applesmc.c
index 0c94770..aacc0c4 100644
--- a/drivers/hwmon/applesmc.c
+++ b/drivers/hwmon/applesmc.c
@@ -84,12 +84,15 @@
/* Set 0: Macbook Pro */
{ "TA0P", "TB0T", "TC0D", "TC0P", "TG0H", "TG0P", "TG0T", "Th0H",
"Th1H", "Tm0P", "Ts0P", "Ts1P", NULL },
-/* Set 1: Macbook set */
+/* Set 1: Macbook2 set */
+ { "TB0T", "TC0D", "TC0P", "TM0P", "TN0P", "TN1P", "TTF0", "Th0H",
+ "Th0S", "Th1H", NULL },
+/* Set 2: Macbook set */
{ "TB0T", "TC0D", "TC0P", "TM0P", "TN0P", "TN1P", "Th0H", "Th0S",
"Th1H", "Ts0P", NULL },
-/* Set 2: Macmini set */
+/* Set 3: Macmini set */
{ "TC0D", "TC0P", NULL },
-/* Set 3: Mac Pro (2 x Quad-Core) */
+/* Set 4: Mac Pro (2 x Quad-Core) */
{ "TA0P", "TCAG", "TCAH", "TCBG", "TCBH", "TC0C", "TC0D", "TC0P",
"TC1C", "TC1D", "TC2C", "TC2D", "TC3C", "TC3D", "THTG", "TH0P",
"TH1P", "TH2P", "TH3P", "TMAP", "TMAS", "TMBS", "TM0P", "TM0S",
@@ -1212,12 +1215,14 @@
static __initdata struct dmi_match_data applesmc_dmi_data[] = {
/* MacBook Pro: accelerometer, backlight and temperature set 0 */
{ .accelerometer = 1, .light = 1, .temperature_set = 0 },
-/* MacBook: accelerometer and temperature set 1 */
+/* MacBook2: accelerometer and temperature set 1 */
{ .accelerometer = 1, .light = 0, .temperature_set = 1 },
-/* MacMini: temperature set 2 */
- { .accelerometer = 0, .light = 0, .temperature_set = 2 },
-/* MacPro: temperature set 3 */
+/* MacBook: accelerometer and temperature set 2 */
+ { .accelerometer = 1, .light = 0, .temperature_set = 2 },
+/* MacMini: temperature set 3 */
{ .accelerometer = 0, .light = 0, .temperature_set = 3 },
+/* MacPro: temperature set 4 */
+ { .accelerometer = 0, .light = 0, .temperature_set = 4 },
};
/* Note that DMI_MATCH(...,"MacBook") will match "MacBookPro1,1".
@@ -1229,16 +1234,20 @@
(void*)&applesmc_dmi_data[0]},
{ applesmc_dmi_match, "Apple MacBook", {
DMI_MATCH(DMI_BOARD_VENDOR,"Apple"),
- DMI_MATCH(DMI_PRODUCT_NAME,"MacBook") },
+ DMI_MATCH(DMI_PRODUCT_NAME,"MacBook2") },
(void*)&applesmc_dmi_data[1]},
+ { applesmc_dmi_match, "Apple MacBook", {
+ DMI_MATCH(DMI_BOARD_VENDOR,"Apple"),
+ DMI_MATCH(DMI_PRODUCT_NAME,"MacBook") },
+ (void*)&applesmc_dmi_data[2]},
{ applesmc_dmi_match, "Apple Macmini", {
DMI_MATCH(DMI_BOARD_VENDOR,"Apple"),
DMI_MATCH(DMI_PRODUCT_NAME,"Macmini") },
- (void*)&applesmc_dmi_data[2]},
+ (void*)&applesmc_dmi_data[3]},
{ applesmc_dmi_match, "Apple MacPro2", {
DMI_MATCH(DMI_BOARD_VENDOR,"Apple"),
DMI_MATCH(DMI_PRODUCT_NAME,"MacPro2") },
- (void*)&applesmc_dmi_data[3]},
+ (void*)&applesmc_dmi_data[4]},
{ .ident = NULL }
};
diff --git a/drivers/hwmon/asb100.c b/drivers/hwmon/asb100.c
index 950cea8..84712a2 100644
--- a/drivers/hwmon/asb100.c
+++ b/drivers/hwmon/asb100.c
@@ -49,7 +49,7 @@
#include "lm75.h"
/* I2C addresses to scan */
-static unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(asb100);
diff --git a/drivers/hwmon/atxp1.c b/drivers/hwmon/atxp1.c
index cce3350..01c17e3 100644
--- a/drivers/hwmon/atxp1.c
+++ b/drivers/hwmon/atxp1.c
@@ -42,7 +42,7 @@
#define ATXP1_VIDMASK 0x1f
#define ATXP1_GPIO1MASK 0x0f
-static unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END };
I2C_CLIENT_INSMOD_1(atxp1);
diff --git a/drivers/hwmon/coretemp.c b/drivers/hwmon/coretemp.c
index 3ee60d2..70239ac 100644
--- a/drivers/hwmon/coretemp.c
+++ b/drivers/hwmon/coretemp.c
@@ -38,7 +38,8 @@
#define DRVNAME "coretemp"
-typedef enum { SHOW_TEMP, SHOW_TJMAX, SHOW_LABEL, SHOW_NAME } SHOW;
+typedef enum { SHOW_TEMP, SHOW_TJMAX, SHOW_TTARGET, SHOW_LABEL,
+ SHOW_NAME } SHOW;
/*
* Functions declaration
@@ -55,6 +56,7 @@
unsigned long last_updated; /* in jiffies */
int temp;
int tjmax;
+ int ttarget;
u8 alarm;
};
@@ -93,9 +95,10 @@
if (attr->index == SHOW_TEMP)
err = data->valid ? sprintf(buf, "%d\n", data->temp) : -EAGAIN;
- else
+ else if (attr->index == SHOW_TJMAX)
err = sprintf(buf, "%d\n", data->tjmax);
-
+ else
+ err = sprintf(buf, "%d\n", data->ttarget);
return err;
}
@@ -103,6 +106,8 @@
SHOW_TEMP);
static SENSOR_DEVICE_ATTR(temp1_crit, S_IRUGO, show_temp, NULL,
SHOW_TJMAX);
+static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, show_temp, NULL,
+ SHOW_TTARGET);
static DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL);
static SENSOR_DEVICE_ATTR(temp1_label, S_IRUGO, show_name, NULL, SHOW_LABEL);
static SENSOR_DEVICE_ATTR(name, S_IRUGO, show_name, NULL, SHOW_NAME);
@@ -147,6 +152,56 @@
return data;
}
+static int __devinit adjust_tjmax(struct cpuinfo_x86 *c, u32 id, struct device *dev)
+{
+ /* The 100C is default for both mobile and non mobile CPUs */
+
+ int tjmax = 100000;
+ int ismobile = 1;
+ int err;
+ u32 eax, edx;
+
+ /* Early chips have no MSR for TjMax */
+
+ if ((c->x86_model == 0xf) && (c->x86_mask < 4)) {
+ ismobile = 0;
+ }
+
+ if ((c->x86_model > 0xe) && (ismobile)) {
+
+ /* Now we can detect the mobile CPU using Intel provided table
+ http://softwarecommunity.intel.com/Wiki/Mobility/720.htm
+ For Core2 cores, check MSR 0x17, bit 28 1 = Mobile CPU
+ */
+
+ err = rdmsr_safe_on_cpu(id, 0x17, &eax, &edx);
+ if (err) {
+ dev_warn(dev,
+ "Unable to access MSR 0x17, assuming desktop"
+ " CPU\n");
+ ismobile = 0;
+ } else if (!(eax & 0x10000000)) {
+ ismobile = 0;
+ }
+ }
+
+ if (ismobile) {
+
+ err = rdmsr_safe_on_cpu(id, 0xee, &eax, &edx);
+ if (err) {
+ dev_warn(dev,
+ "Unable to access MSR 0xEE, for Tjmax, left"
+ " at default");
+ } else if (eax & 0x40000000) {
+ tjmax = 85000;
+ }
+ } else {
+ dev_warn(dev, "Using relative temperature scale!\n");
+ }
+
+ return tjmax;
+}
+
static int __devinit coretemp_probe(struct platform_device *pdev)
{
struct coretemp_data *data;
@@ -163,8 +218,6 @@
data->id = pdev->id;
data->name = "coretemp";
mutex_init(&data->update_lock);
- /* Tjmax default is 100 degrees C */
- data->tjmax = 100000;
/* test if we can access the THERM_STATUS MSR */
err = rdmsr_safe_on_cpu(data->id, MSR_IA32_THERM_STATUS, &eax, &edx);
@@ -191,40 +244,29 @@
}
}
- /* Some processors have Tjmax 85 following magic should detect it
- Intel won't disclose the information without signed NDA, but
- individuals cannot sign it. Catch(ed) 22.
- */
+ data->tjmax = adjust_tjmax(c, data->id, &pdev->dev);
+ platform_set_drvdata(pdev, data);
- if (((c->x86_model == 0xf) && (c->x86_mask > 3)) ||
- (c->x86_model == 0xe)) {
- err = rdmsr_safe_on_cpu(data->id, 0xee, &eax, &edx);
+ /* read the still undocumented IA32_TEMPERATURE_TARGET it exists
+ on older CPUs but not in this register */
+
+ if (c->x86_model > 0xe) {
+ err = rdmsr_safe_on_cpu(data->id, 0x1a2, &eax, &edx);
if (err) {
- dev_warn(&pdev->dev,
- "Unable to access MSR 0xEE, Tjmax left at %d "
- "degrees C\n", data->tjmax/1000);
- } else if (eax & 0x40000000) {
- data->tjmax = 85000;
+ dev_warn(&pdev->dev, "Unable to read"
+ " IA32_TEMPERATURE_TARGET MSR\n");
+ } else {
+ data->ttarget = data->tjmax -
+ (((eax >> 8) & 0xff) * 1000);
+ err = device_create_file(&pdev->dev,
+ &sensor_dev_attr_temp1_max.dev_attr);
+ if (err)
+ goto exit_free;
}
}
- /* Intel says that above should not work for desktop Core2 processors,
- but it seems to work. There is no other way how get the absolute
- readings. Warn the user about this. First check if are desktop,
- bit 50 of MSR_IA32_PLATFORM_ID should be 0.
- */
-
- rdmsr_safe_on_cpu(data->id, MSR_IA32_PLATFORM_ID, &eax, &edx);
-
- if ((c->x86_model == 0xf) && (!(edx & 0x00040000))) {
- dev_warn(&pdev->dev, "Using undocumented features, absolute "
- "temperature might be wrong!\n");
- }
-
- platform_set_drvdata(pdev, data);
-
if ((err = sysfs_create_group(&pdev->dev.kobj, &coretemp_group)))
- goto exit_free;
+ goto exit_dev;
data->hwmon_dev = hwmon_device_register(&pdev->dev);
if (IS_ERR(data->hwmon_dev)) {
@@ -238,6 +280,8 @@
exit_class:
sysfs_remove_group(&pdev->dev.kobj, &coretemp_group);
+exit_dev:
+ device_remove_file(&pdev->dev, &sensor_dev_attr_temp1_max.dev_attr);
exit_free:
kfree(data);
exit:
@@ -250,6 +294,7 @@
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&pdev->dev.kobj, &coretemp_group);
+ device_remove_file(&pdev->dev, &sensor_dev_attr_temp1_max.dev_attr);
platform_set_drvdata(pdev, NULL);
kfree(data);
return 0;
@@ -330,7 +375,7 @@
mutex_unlock(&pdev_list_mutex);
}
-static int coretemp_cpu_callback(struct notifier_block *nfb,
+static int __cpuinit coretemp_cpu_callback(struct notifier_block *nfb,
unsigned long action, void *hcpu)
{
unsigned int cpu = (unsigned long) hcpu;
@@ -347,7 +392,7 @@
return NOTIFY_OK;
}
-static struct notifier_block coretemp_cpu_notifier = {
+static struct notifier_block coretemp_cpu_notifier __refdata = {
.notifier_call = coretemp_cpu_callback,
};
#endif /* !CONFIG_HOTPLUG_CPU */
@@ -368,10 +413,10 @@
for_each_online_cpu(i) {
struct cpuinfo_x86 *c = &cpu_data(i);
- /* check if family 6, models e, f, 16 */
+ /* check if family 6, models 0xe, 0xf, 0x16, 0x17 */
if ((c->cpuid_level < 0) || (c->x86 != 0x6) ||
!((c->x86_model == 0xe) || (c->x86_model == 0xf) ||
- (c->x86_model == 0x16))) {
+ (c->x86_model == 0x16) || (c->x86_model == 0x17))) {
/* supported CPU not found, but report the unknown
family 6 CPU */
diff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c
index ddddd9f..7673f65 100644
--- a/drivers/hwmon/dme1737.c
+++ b/drivers/hwmon/dme1737.c
@@ -49,7 +49,7 @@
MODULE_PARM_DESC(force_id, "Override the detected device ID");
/* Addresses to scan */
-static unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END};
+static const unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END};
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(dme1737);
diff --git a/drivers/hwmon/ds1621.c b/drivers/hwmon/ds1621.c
index 3f5163d..5f300ff 100644
--- a/drivers/hwmon/ds1621.c
+++ b/drivers/hwmon/ds1621.c
@@ -34,7 +34,7 @@
#include "lm75.h"
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
+static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
/* Insmod parameters */
diff --git a/drivers/hwmon/f75375s.c b/drivers/hwmon/f75375s.c
index 6892f76..1464338 100644
--- a/drivers/hwmon/f75375s.c
+++ b/drivers/hwmon/f75375s.c
@@ -37,7 +37,7 @@
#include <linux/f75375s.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2d, 0x2e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_2(f75373, f75375);
diff --git a/drivers/hwmon/fscher.c b/drivers/hwmon/fscher.c
index 721c701..ed26b66 100644
--- a/drivers/hwmon/fscher.c
+++ b/drivers/hwmon/fscher.c
@@ -40,7 +40,7 @@
* Addresses to scan
*/
-static unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/fschmd.c b/drivers/hwmon/fschmd.c
index b7c9eef..bd89d27 100644
--- a/drivers/hwmon/fschmd.c
+++ b/drivers/hwmon/fschmd.c
@@ -44,7 +44,7 @@
#include <linux/dmi.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_5(fscpos, fscher, fscscy, fschrc, fschmd);
diff --git a/drivers/hwmon/fscpos.c b/drivers/hwmon/fscpos.c
index 2f10753..00f4848 100644
--- a/drivers/hwmon/fscpos.c
+++ b/drivers/hwmon/fscpos.c
@@ -43,7 +43,7 @@
/*
* Addresses to scan
*/
-static unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/gl518sm.c b/drivers/hwmon/gl518sm.c
index 3b1ac48..33e9e8a 100644
--- a/drivers/hwmon/gl518sm.c
+++ b/drivers/hwmon/gl518sm.c
@@ -44,7 +44,7 @@
#include <linux/sysfs.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_2(gl518sm_r00, gl518sm_r80);
diff --git a/drivers/hwmon/gl520sm.c b/drivers/hwmon/gl520sm.c
index 03ecdc3..8984ef1 100644
--- a/drivers/hwmon/gl520sm.c
+++ b/drivers/hwmon/gl520sm.c
@@ -39,7 +39,7 @@
MODULE_PARM_DESC(extra_sensor_type, "Type of extra sensor (0=autodetect, 1=temperature, 2=voltage)");
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(gl520sm);
diff --git a/drivers/hwmon/lm63.c b/drivers/hwmon/lm63.c
index 650b07d..1162870 100644
--- a/drivers/hwmon/lm63.c
+++ b/drivers/hwmon/lm63.c
@@ -53,7 +53,7 @@
* Address is fully defined internally and cannot be changed.
*/
-static unsigned short normal_i2c[] = { 0x4c, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x4c, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/lm75.c b/drivers/hwmon/lm75.c
index e5c35a3..115f409 100644
--- a/drivers/hwmon/lm75.c
+++ b/drivers/hwmon/lm75.c
@@ -31,7 +31,7 @@
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
+static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
/* Insmod parameters */
diff --git a/drivers/hwmon/lm77.c b/drivers/hwmon/lm77.c
index 459b70a..36d5a8c 100644
--- a/drivers/hwmon/lm77.c
+++ b/drivers/hwmon/lm77.c
@@ -36,7 +36,8 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
+ I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(lm77);
diff --git a/drivers/hwmon/lm78.c b/drivers/hwmon/lm78.c
index 0a9eb1f..ed7859f 100644
--- a/drivers/hwmon/lm78.c
+++ b/drivers/hwmon/lm78.c
@@ -37,8 +37,8 @@
static struct platform_device *pdev;
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d,
- 0x2e, 0x2f, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d,
+ 0x2e, 0x2f, I2C_CLIENT_END };
static unsigned short isa_address = 0x290;
/* Insmod parameters */
diff --git a/drivers/hwmon/lm80.c b/drivers/hwmon/lm80.c
index a2ca055..26c91c9 100644
--- a/drivers/hwmon/lm80.c
+++ b/drivers/hwmon/lm80.c
@@ -32,8 +32,8 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c,
- 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d,
+ 0x2e, 0x2f, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(lm80);
diff --git a/drivers/hwmon/lm83.c b/drivers/hwmon/lm83.c
index 6e8903a..6a8642f 100644
--- a/drivers/hwmon/lm83.c
+++ b/drivers/hwmon/lm83.c
@@ -48,10 +48,8 @@
* addresses.
*/
-static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a,
- 0x29, 0x2a, 0x2b,
- 0x4c, 0x4d, 0x4e,
- I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = {
+ 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index 4bb0f29..182fe6a 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -35,7 +35,7 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_6(lm85b, lm85c, adm1027, adt7463, emc6d100, emc6d102);
diff --git a/drivers/hwmon/lm87.c b/drivers/hwmon/lm87.c
index 8ee07c5..e1c183f 100644
--- a/drivers/hwmon/lm87.c
+++ b/drivers/hwmon/lm87.c
@@ -73,7 +73,7 @@
* LM87 has three possible addresses: 0x2c, 0x2d and 0x2e.
*/
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
index f7ec95b..d1a3da3 100644
--- a/drivers/hwmon/lm90.c
+++ b/drivers/hwmon/lm90.c
@@ -101,10 +101,8 @@
* 0x4c, 0x4d or 0x4e.
*/
-static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a,
- 0x29, 0x2a, 0x2b,
- 0x4c, 0x4d, 0x4e,
- I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = {
+ 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/lm92.c b/drivers/hwmon/lm92.c
index af5c77d..c31942e 100644
--- a/drivers/hwmon/lm92.c
+++ b/drivers/hwmon/lm92.c
@@ -45,13 +45,14 @@
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
/* The LM92 and MAX6635 have 2 two-state pins for address selection,
resulting in 4 possible addresses. */
-static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
- I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
+ I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(lm92);
@@ -209,6 +210,14 @@
return sprintf(buf, "%d\n", ALARMS_FROM_REG(data->temp1_input));
}
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ int bitnr = to_sensor_dev_attr(attr)->index;
+ struct lm92_data *data = lm92_update_device(dev);
+ return sprintf(buf, "%d\n", (data->temp1_input >> bitnr) & 1);
+}
+
static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp1_input, NULL);
static DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_temp1_crit,
set_temp1_crit);
@@ -221,6 +230,9 @@
set_temp1_max);
static DEVICE_ATTR(temp1_max_hyst, S_IRUGO, show_temp1_max_hyst, NULL);
static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
+static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 1);
/*
@@ -297,7 +309,9 @@
&dev_attr_temp1_max.attr,
&dev_attr_temp1_max_hyst.attr,
&dev_attr_alarms.attr,
-
+ &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
NULL
};
diff --git a/drivers/hwmon/lm93.c b/drivers/hwmon/lm93.c
index ea61946..5e678f5 100644
--- a/drivers/hwmon/lm93.c
+++ b/drivers/hwmon/lm93.c
@@ -142,7 +142,7 @@
I2C_FUNC_SMBUS_WORD_DATA)
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(lm93);
diff --git a/drivers/hwmon/max1619.c b/drivers/hwmon/max1619.c
index 38a44c3..7e7267a 100644
--- a/drivers/hwmon/max1619.c
+++ b/drivers/hwmon/max1619.c
@@ -32,14 +32,13 @@
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
#include <linux/sysfs.h>
-static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a,
- 0x29, 0x2a, 0x2b,
- 0x4c, 0x4d, 0x4e,
- I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = {
+ 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END };
/*
* Insmod parameters
@@ -161,6 +160,14 @@
return sprintf(buf, "%d\n", data->alarms);
}
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ int bitnr = to_sensor_dev_attr(attr)->index;
+ struct max1619_data *data = max1619_update_device(dev);
+ return sprintf(buf, "%d\n", (data->alarms >> bitnr) & 1);
+}
+
static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_input1, NULL);
static DEVICE_ATTR(temp2_input, S_IRUGO, show_temp_input2, NULL);
static DEVICE_ATTR(temp2_min, S_IWUSR | S_IRUGO, show_temp_low2,
@@ -172,6 +179,10 @@
static DEVICE_ATTR(temp2_crit_hyst, S_IWUSR | S_IRUGO, show_temp_hyst2,
set_temp_hyst2);
static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
+static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp2_min_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 4);
static struct attribute *max1619_attributes[] = {
&dev_attr_temp1_input.attr,
@@ -182,6 +193,10 @@
&dev_attr_temp2_crit_hyst.attr,
&dev_attr_alarms.attr,
+ &sensor_dev_attr_temp2_crit_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_fault.dev_attr.attr,
+ &sensor_dev_attr_temp2_min_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
NULL
};
diff --git a/drivers/hwmon/max6650.c b/drivers/hwmon/max6650.c
index 755570c..52d528b 100644
--- a/drivers/hwmon/max6650.c
+++ b/drivers/hwmon/max6650.c
@@ -44,7 +44,8 @@
* Addresses to scan. There are four disjoint possibilities, by pin config.
*/
-static unsigned short normal_i2c[] = {0x1b, 0x1f, 0x48, 0x4b, I2C_CLIENT_END};
+static const unsigned short normal_i2c[] = {0x1b, 0x1f, 0x48, 0x4b,
+ I2C_CLIENT_END};
/*
* Insmod parameters
diff --git a/drivers/hwmon/smsc47m1.c b/drivers/hwmon/smsc47m1.c
index 0d7f0c4..d1b4985 100644
--- a/drivers/hwmon/smsc47m1.c
+++ b/drivers/hwmon/smsc47m1.c
@@ -198,6 +198,14 @@
return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[attr->index]));
}
+static ssize_t get_fan_alarm(struct device *dev, struct device_attribute
+ *devattr, char *buf)
+{
+ int bitnr = to_sensor_dev_attr(devattr)->index;
+ struct smsc47m1_data *data = smsc47m1_update_device(dev, 0);
+ return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
+}
+
static ssize_t get_pwm(struct device *dev, struct device_attribute
*devattr, char *buf)
{
@@ -347,6 +355,8 @@
get_fan_min, set_fan_min, offset - 1); \
static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, \
get_fan_div, set_fan_div, offset - 1); \
+static SENSOR_DEVICE_ATTR(fan##offset##_alarm, S_IRUGO, get_fan_alarm, \
+ NULL, offset - 1); \
static SENSOR_DEVICE_ATTR(pwm##offset, S_IRUGO | S_IWUSR, \
get_pwm, set_pwm, offset - 1); \
static SENSOR_DEVICE_ATTR(pwm##offset##_enable, S_IRUGO | S_IWUSR, \
@@ -374,12 +384,15 @@
&sensor_dev_attr_fan1_input.dev_attr.attr,
&sensor_dev_attr_fan1_min.dev_attr.attr,
&sensor_dev_attr_fan1_div.dev_attr.attr,
+ &sensor_dev_attr_fan1_alarm.dev_attr.attr,
&sensor_dev_attr_fan2_input.dev_attr.attr,
&sensor_dev_attr_fan2_min.dev_attr.attr,
&sensor_dev_attr_fan2_div.dev_attr.attr,
+ &sensor_dev_attr_fan2_alarm.dev_attr.attr,
&sensor_dev_attr_fan3_input.dev_attr.attr,
&sensor_dev_attr_fan3_min.dev_attr.attr,
&sensor_dev_attr_fan3_div.dev_attr.attr,
+ &sensor_dev_attr_fan3_alarm.dev_attr.attr,
&sensor_dev_attr_pwm1.dev_attr.attr,
&sensor_dev_attr_pwm1_enable.dev_attr.attr,
@@ -533,7 +546,9 @@
|| (err = device_create_file(dev,
&sensor_dev_attr_fan1_min.dev_attr))
|| (err = device_create_file(dev,
- &sensor_dev_attr_fan1_div.dev_attr)))
+ &sensor_dev_attr_fan1_div.dev_attr))
+ || (err = device_create_file(dev,
+ &sensor_dev_attr_fan1_alarm.dev_attr)))
goto error_remove_files;
} else
dev_dbg(dev, "Fan 1 not enabled by hardware, skipping\n");
@@ -544,7 +559,9 @@
|| (err = device_create_file(dev,
&sensor_dev_attr_fan2_min.dev_attr))
|| (err = device_create_file(dev,
- &sensor_dev_attr_fan2_div.dev_attr)))
+ &sensor_dev_attr_fan2_div.dev_attr))
+ || (err = device_create_file(dev,
+ &sensor_dev_attr_fan2_alarm.dev_attr)))
goto error_remove_files;
} else
dev_dbg(dev, "Fan 2 not enabled by hardware, skipping\n");
@@ -555,7 +572,9 @@
|| (err = device_create_file(dev,
&sensor_dev_attr_fan3_min.dev_attr))
|| (err = device_create_file(dev,
- &sensor_dev_attr_fan3_div.dev_attr)))
+ &sensor_dev_attr_fan3_div.dev_attr))
+ || (err = device_create_file(dev,
+ &sensor_dev_attr_fan3_alarm.dev_attr)))
goto error_remove_files;
} else if (data->type == smsc47m2)
dev_dbg(dev, "Fan 3 not enabled by hardware, skipping\n");
diff --git a/drivers/hwmon/smsc47m192.c b/drivers/hwmon/smsc47m192.c
index 8b0c188..3c9db65 100644
--- a/drivers/hwmon/smsc47m192.c
+++ b/drivers/hwmon/smsc47m192.c
@@ -34,7 +34,7 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(smsc47m192);
diff --git a/drivers/hwmon/thmc50.c b/drivers/hwmon/thmc50.c
index 04dd769..76a3859 100644
--- a/drivers/hwmon/thmc50.c
+++ b/drivers/hwmon/thmc50.c
@@ -32,7 +32,7 @@
MODULE_LICENSE("GPL");
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_2(thmc50, adm1022);
@@ -52,9 +52,9 @@
*/
#define THMC50_REG_INTR 0x41
-const static u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 };
-const static u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C };
-const static u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B };
+static const u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 };
+static const u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C };
+static const u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B };
#define THMC50_REG_CONF_nFANOFF 0x20
diff --git a/drivers/hwmon/via686a.c b/drivers/hwmon/via686a.c
index 2635bba..f1ee5e7 100644
--- a/drivers/hwmon/via686a.c
+++ b/drivers/hwmon/via686a.c
@@ -533,6 +533,24 @@
}
static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ int bitnr = to_sensor_dev_attr(attr)->index;
+ struct via686a_data *data = via686a_update_device(dev);
+ return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
+}
+static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
+static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
+static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8);
+static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 11);
+static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 15);
+static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6);
+static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7);
+
static ssize_t show_name(struct device *dev, struct device_attribute
*devattr, char *buf)
{
@@ -557,6 +575,11 @@
&sensor_dev_attr_in2_max.dev_attr.attr,
&sensor_dev_attr_in3_max.dev_attr.attr,
&sensor_dev_attr_in4_max.dev_attr.attr,
+ &sensor_dev_attr_in0_alarm.dev_attr.attr,
+ &sensor_dev_attr_in1_alarm.dev_attr.attr,
+ &sensor_dev_attr_in2_alarm.dev_attr.attr,
+ &sensor_dev_attr_in3_alarm.dev_attr.attr,
+ &sensor_dev_attr_in4_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
@@ -567,6 +590,9 @@
&sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
+ &sensor_dev_attr_temp1_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp3_alarm.dev_attr.attr,
&sensor_dev_attr_fan1_input.dev_attr.attr,
&sensor_dev_attr_fan2_input.dev_attr.attr,
@@ -574,6 +600,8 @@
&sensor_dev_attr_fan2_min.dev_attr.attr,
&sensor_dev_attr_fan1_div.dev_attr.attr,
&sensor_dev_attr_fan2_div.dev_attr.attr,
+ &sensor_dev_attr_fan1_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan2_alarm.dev_attr.attr,
&dev_attr_alarms.attr,
&dev_attr_name.attr,
diff --git a/drivers/hwmon/vt8231.c b/drivers/hwmon/vt8231.c
index f876617..5bc5727 100644
--- a/drivers/hwmon/vt8231.c
+++ b/drivers/hwmon/vt8231.c
@@ -2,7 +2,7 @@
vt8231.c - Part of lm_sensors, Linux kernel modules
for hardware monitoring
- Copyright (c) 2005 Roger Lucas <roger@planbit.co.uk>
+ Copyright (c) 2005 Roger Lucas <vt8231@hiddenengine.co.uk>
Copyright (c) 2002 Mark D. Studebaker <mdsxyz123@yahoo.com>
Aaron M. Marsh <amarsh@sdf.lonestar.org>
@@ -541,6 +541,28 @@
}
static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ int bitnr = to_sensor_dev_attr(attr)->index;
+ struct vt8231_data *data = vt8231_update_device(dev);
+ return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
+}
+static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 11);
+static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp4_alarm, S_IRUGO, show_alarm, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp5_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp6_alarm, S_IRUGO, show_alarm, NULL, 8);
+static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 11);
+static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 0);
+static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 1);
+static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8);
+static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6);
+static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7);
+
static ssize_t show_name(struct device *dev, struct device_attribute
*devattr, char *buf)
{
@@ -549,36 +571,42 @@
}
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
-static struct attribute *vt8231_attributes_temps[6][4] = {
+static struct attribute *vt8231_attributes_temps[6][5] = {
{
&dev_attr_temp1_input.attr,
&dev_attr_temp1_max_hyst.attr,
&dev_attr_temp1_max.attr,
+ &sensor_dev_attr_temp1_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_temp2_input.dev_attr.attr,
&sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp2_max.dev_attr.attr,
+ &sensor_dev_attr_temp2_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_temp3_input.dev_attr.attr,
&sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp3_max.dev_attr.attr,
+ &sensor_dev_attr_temp3_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_temp4_input.dev_attr.attr,
&sensor_dev_attr_temp4_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp4_max.dev_attr.attr,
+ &sensor_dev_attr_temp4_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_temp5_input.dev_attr.attr,
&sensor_dev_attr_temp5_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp5_max.dev_attr.attr,
+ &sensor_dev_attr_temp5_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_temp6_input.dev_attr.attr,
&sensor_dev_attr_temp6_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp6_max.dev_attr.attr,
+ &sensor_dev_attr_temp6_alarm.dev_attr.attr,
NULL
}
};
@@ -592,36 +620,42 @@
{ .attrs = vt8231_attributes_temps[5] },
};
-static struct attribute *vt8231_attributes_volts[6][4] = {
+static struct attribute *vt8231_attributes_volts[6][5] = {
{
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in0_min.dev_attr.attr,
&sensor_dev_attr_in0_max.dev_attr.attr,
+ &sensor_dev_attr_in0_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in1_min.dev_attr.attr,
&sensor_dev_attr_in1_max.dev_attr.attr,
+ &sensor_dev_attr_in1_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in2_min.dev_attr.attr,
&sensor_dev_attr_in2_max.dev_attr.attr,
+ &sensor_dev_attr_in2_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_in3_input.dev_attr.attr,
&sensor_dev_attr_in3_min.dev_attr.attr,
&sensor_dev_attr_in3_max.dev_attr.attr,
+ &sensor_dev_attr_in3_alarm.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_in4_input.dev_attr.attr,
&sensor_dev_attr_in4_min.dev_attr.attr,
&sensor_dev_attr_in4_max.dev_attr.attr,
+ &sensor_dev_attr_in4_alarm.dev_attr.attr,
NULL
}, {
&dev_attr_in5_input.attr,
&dev_attr_in5_min.attr,
&dev_attr_in5_max.attr,
+ &sensor_dev_attr_in5_alarm.dev_attr.attr,
NULL
}
};
@@ -642,6 +676,8 @@
&sensor_dev_attr_fan2_min.dev_attr.attr,
&sensor_dev_attr_fan1_div.dev_attr.attr,
&sensor_dev_attr_fan2_div.dev_attr.attr,
+ &sensor_dev_attr_fan1_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan2_alarm.dev_attr.attr,
&dev_attr_alarms.attr,
&dev_attr_name.attr,
NULL
@@ -963,7 +999,7 @@
}
}
-MODULE_AUTHOR("Roger Lucas <roger@planbit.co.uk>");
+MODULE_AUTHOR("Roger Lucas <vt8231@hiddenengine.co.uk>");
MODULE_DESCRIPTION("VT8231 sensors");
MODULE_LICENSE("GPL");
diff --git a/drivers/hwmon/w83781d.c b/drivers/hwmon/w83781d.c
index 7421f6e..5c85670e 100644
--- a/drivers/hwmon/w83781d.c
+++ b/drivers/hwmon/w83781d.c
@@ -53,8 +53,8 @@
static struct platform_device *pdev;
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d,
- 0x2e, 0x2f, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d,
+ 0x2e, 0x2f, I2C_CLIENT_END };
static unsigned short isa_address = 0x290;
/* Insmod parameters */
diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c
index 85bd21e..85077c4 100644
--- a/drivers/hwmon/w83791d.c
+++ b/drivers/hwmon/w83791d.c
@@ -47,7 +47,8 @@
#define NUMBER_OF_TEMPIN 3
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
+ I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(w83791d);
diff --git a/drivers/hwmon/w83792d.c b/drivers/hwmon/w83792d.c
index 007449d..299629d 100644
--- a/drivers/hwmon/w83792d.c
+++ b/drivers/hwmon/w83792d.c
@@ -46,7 +46,8 @@
#include <linux/sysfs.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
+ I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(w83792d);
diff --git a/drivers/hwmon/w83793.c b/drivers/hwmon/w83793.c
index 3ba1d6b..ee35af9 100644
--- a/drivers/hwmon/w83793.c
+++ b/drivers/hwmon/w83793.c
@@ -37,7 +37,8 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
+ I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(w83793);
diff --git a/drivers/hwmon/w83l785ts.c b/drivers/hwmon/w83l785ts.c
index 1d6259d..77f2d48 100644
--- a/drivers/hwmon/w83l785ts.c
+++ b/drivers/hwmon/w83l785ts.c
@@ -49,7 +49,7 @@
* Address is fully defined internally and cannot be changed.
*/
-static unsigned short normal_i2c[] = { 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2e, I2C_CLIENT_END };
/*
* Insmod parameters
diff --git a/drivers/hwmon/w83l786ng.c b/drivers/hwmon/w83l786ng.c
index 1dbee4f..41e22dd 100644
--- a/drivers/hwmon/w83l786ng.c
+++ b/drivers/hwmon/w83l786ng.c
@@ -35,7 +35,7 @@
#include <linux/mutex.h>
/* Addresses to scan */
-static unsigned short normal_i2c[] = { 0x2e, 0x2f, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2e, 0x2f, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(w83l786ng);
