/* SPDX-License-Identifier: GPL-2.0 */

#ifndef XILINX_LL_TEMAC_H
#define XILINX_LL_TEMAC_H

#include <linux/netdevice.h>
#include <linux/of.h>
#include <linux/spinlock.h>

#ifdef CONFIG_PPC_DCR
#include <asm/dcr.h>
#include <asm/dcr-regs.h>
#endif

/* packet size info */
#define XTE_HDR_SIZE			14      /* size of Ethernet header */
#define XTE_TRL_SIZE			4       /* size of Ethernet trailer (FCS) */
#define XTE_JUMBO_MTU			9000
#define XTE_MAX_JUMBO_FRAME_SIZE	(XTE_JUMBO_MTU + XTE_HDR_SIZE + XTE_TRL_SIZE)

/*  Configuration options */

/*  Accept all incoming packets.
 *  This option defaults to disabled (cleared)
 */
#define XTE_OPTION_PROMISC                      (1 << 0)
/*  Jumbo frame support for Tx & Rx.
 *  This option defaults to disabled (cleared)
 */
#define XTE_OPTION_JUMBO                        (1 << 1)
/*  VLAN Rx & Tx frame support.
 *  This option defaults to disabled (cleared)
 */
#define XTE_OPTION_VLAN                         (1 << 2)
/*  Enable recognition of flow control frames on Rx
 *  This option defaults to enabled (set)
 */
#define XTE_OPTION_FLOW_CONTROL                 (1 << 4)
/*  Strip FCS and PAD from incoming frames.
 *  Note: PAD from VLAN frames is not stripped.
 *  This option defaults to disabled (set)
 */
#define XTE_OPTION_FCS_STRIP                    (1 << 5)
/*  Generate FCS field and add PAD automatically for outgoing frames.
 *  This option defaults to enabled (set)
 */
#define XTE_OPTION_FCS_INSERT                   (1 << 6)
/*  Enable Length/Type error checking for incoming frames. When this option is
 *  set, the MAC will filter frames that have a mismatched type/length field
 *  and if XTE_OPTION_REPORT_RXERR is set, the user is notified when these
 *  types of frames are encountered. When this option is cleared, the MAC will
 *  allow these types of frames to be received.
 *  This option defaults to enabled (set)
 */
#define XTE_OPTION_LENTYPE_ERR                  (1 << 7)
/*  Enable the transmitter.
 *  This option defaults to enabled (set)
 */
#define XTE_OPTION_TXEN                         (1 << 11)
/*  Enable the receiver
 *  This option defaults to enabled (set)
 */
#define XTE_OPTION_RXEN                         (1 << 12)

/*  Default options set when device is initialized or reset */
#define XTE_OPTION_DEFAULTS                     \
	(XTE_OPTION_TXEN |                          \
	 XTE_OPTION_FLOW_CONTROL |                  \
	 XTE_OPTION_RXEN)

/* XPS_LL_TEMAC SDMA registers definition */

#define TX_NXTDESC_PTR      0x00            /* r */
#define TX_CURBUF_ADDR      0x01            /* r */
#define TX_CURBUF_LENGTH    0x02            /* r */
#define TX_CURDESC_PTR      0x03            /* rw */
#define TX_TAILDESC_PTR     0x04            /* rw */
#define TX_CHNL_CTRL        0x05            /* rw */
/*
 *  0:7      24:31       IRQTimeout
 *  8:15     16:23       IRQCount
 *  16:20    11:15       Reserved
 *  21       10          0
 *  22       9           UseIntOnEnd
 *  23       8           LdIRQCnt
 *  24       7           IRQEn
 *  25:28    3:6         Reserved
 *  29       2           IrqErrEn
 *  30       1           IrqDlyEn
 *  31       0           IrqCoalEn
 */
#define CHNL_CTRL_IRQ_IOE       (1 << 9)
#define CHNL_CTRL_IRQ_EN        (1 << 7)
#define CHNL_CTRL_IRQ_ERR_EN    (1 << 2)
#define CHNL_CTRL_IRQ_DLY_EN    (1 << 1)
#define CHNL_CTRL_IRQ_COAL_EN   (1 << 0)
#define TX_IRQ_REG          0x06            /* rw */
/*
 *  0:7      24:31       DltTmrValue
 *  8:15     16:23       ClscCntrValue
 *  16:17    14:15       Reserved
 *  18:21    10:13       ClscCnt
 *  22:23    8:9         DlyCnt
 *  24:28    3::7        Reserved
 *  29       2           ErrIrq
 *  30       1           DlyIrq
 *  31       0           CoalIrq
 */
#define TX_CHNL_STS         0x07            /* r */
/*
 *  0:9      22:31   Reserved
 *  10       21      TailPErr
 *  11       20      CmpErr
 *  12       19      AddrErr
 *  13       18      NxtPErr
 *  14       17      CurPErr
 *  15       16      BsyWr
 *  16:23    8:15    Reserved
 *  24       7       Error
 *  25       6       IOE
 *  26       5       SOE
 *  27       4       Cmplt
 *  28       3       SOP
 *  29       2       EOP
 *  30       1       EngBusy
 *  31       0       Reserved
 */

#define RX_NXTDESC_PTR      0x08            /* r */
#define RX_CURBUF_ADDR      0x09            /* r */
#define RX_CURBUF_LENGTH    0x0a            /* r */
#define RX_CURDESC_PTR      0x0b            /* rw */
#define RX_TAILDESC_PTR     0x0c            /* rw */
#define RX_CHNL_CTRL        0x0d            /* rw */
/*
 *  0:7      24:31       IRQTimeout
 *  8:15     16:23       IRQCount
 *  16:20    11:15       Reserved
 *  21       10          0
 *  22       9           UseIntOnEnd
 *  23       8           LdIRQCnt
 *  24       7           IRQEn
 *  25:28    3:6         Reserved
 *  29       2           IrqErrEn
 *  30       1           IrqDlyEn
 *  31       0           IrqCoalEn
 */
#define RX_IRQ_REG          0x0e            /* rw */
#define IRQ_COAL        (1 << 0)
#define IRQ_DLY         (1 << 1)
#define IRQ_ERR         (1 << 2)
#define IRQ_DMAERR      (1 << 7)            /* this is not documented ??? */
/*
 *  0:7      24:31       DltTmrValue
 *  8:15     16:23       ClscCntrValue
 *  16:17    14:15       Reserved
 *  18:21    10:13       ClscCnt
 *  22:23    8:9         DlyCnt
 *  24:28    3::7        Reserved
 */
#define RX_CHNL_STS         0x0f        /* r */
#define CHNL_STS_ENGBUSY    (1 << 1)
#define CHNL_STS_EOP        (1 << 2)
#define CHNL_STS_SOP        (1 << 3)
#define CHNL_STS_CMPLT      (1 << 4)
#define CHNL_STS_SOE        (1 << 5)
#define CHNL_STS_IOE        (1 << 6)
#define CHNL_STS_ERR        (1 << 7)

#define CHNL_STS_BSYWR      (1 << 16)
#define CHNL_STS_CURPERR    (1 << 17)
#define CHNL_STS_NXTPERR    (1 << 18)
#define CHNL_STS_ADDRERR    (1 << 19)
#define CHNL_STS_CMPERR     (1 << 20)
#define CHNL_STS_TAILERR    (1 << 21)
/*
 *  0:9      22:31   Reserved
 *  10       21      TailPErr
 *  11       20      CmpErr
 *  12       19      AddrErr
 *  13       18      NxtPErr
 *  14       17      CurPErr
 *  15       16      BsyWr
 *  16:23    8:15    Reserved
 *  24       7       Error
 *  25       6       IOE
 *  26       5       SOE
 *  27       4       Cmplt
 *  28       3       SOP
 *  29       2       EOP
 *  30       1       EngBusy
 *  31       0       Reserved
 */

#define DMA_CONTROL_REG             0x10            /* rw */
#define DMA_CONTROL_RST                 (1 << 0)
#define DMA_TAIL_ENABLE                 (1 << 2)

/* XPS_LL_TEMAC direct registers definition */

#define XTE_RAF0_OFFSET              0x00
#define RAF0_RST                        (1 << 0)
#define RAF0_MCSTREJ                    (1 << 1)
#define RAF0_BCSTREJ                    (1 << 2)
#define XTE_TPF0_OFFSET              0x04
#define XTE_IFGP0_OFFSET             0x08
#define XTE_ISR0_OFFSET              0x0c
#define ISR0_HARDACSCMPLT               (1 << 0)
#define ISR0_AUTONEG                    (1 << 1)
#define ISR0_RXCMPLT                    (1 << 2)
#define ISR0_RXREJ                      (1 << 3)
#define ISR0_RXFIFOOVR                  (1 << 4)
#define ISR0_TXCMPLT                    (1 << 5)
#define ISR0_RXDCMLCK                   (1 << 6)

#define XTE_IPR0_OFFSET              0x10
#define XTE_IER0_OFFSET              0x14

#define XTE_MSW0_OFFSET              0x20
#define XTE_LSW0_OFFSET              0x24
#define XTE_CTL0_OFFSET              0x28
#define XTE_RDY0_OFFSET              0x2c

#define XTE_RSE_MIIM_RR_MASK      0x0002
#define XTE_RSE_MIIM_WR_MASK      0x0004
#define XTE_RSE_CFG_RR_MASK       0x0020
#define XTE_RSE_CFG_WR_MASK       0x0040
#define XTE_RDY0_HARD_ACS_RDY_MASK  (0x10000)

/* XPS_LL_TEMAC indirect registers offset definition */

#define	XTE_RXC0_OFFSET			0x00000200 /* Rx configuration word 0 */
#define	XTE_RXC1_OFFSET			0x00000240 /* Rx configuration word 1 */
#define XTE_RXC1_RXRST_MASK		(1 << 31)  /* Receiver reset */
#define XTE_RXC1_RXJMBO_MASK		(1 << 30)  /* Jumbo frame enable */
#define XTE_RXC1_RXFCS_MASK		(1 << 29)  /* FCS not stripped */
#define XTE_RXC1_RXEN_MASK		(1 << 28)  /* Receiver enable */
#define XTE_RXC1_RXVLAN_MASK		(1 << 27)  /* VLAN enable */
#define XTE_RXC1_RXHD_MASK		(1 << 26)  /* Half duplex */
#define XTE_RXC1_RXLT_MASK		(1 << 25)  /* Length/type check disable */

#define XTE_TXC_OFFSET			0x00000280 /*  Tx configuration */
#define XTE_TXC_TXRST_MASK		(1 << 31)  /* Transmitter reset */
#define XTE_TXC_TXJMBO_MASK		(1 << 30)  /* Jumbo frame enable */
#define XTE_TXC_TXFCS_MASK		(1 << 29)  /* Generate FCS */
#define XTE_TXC_TXEN_MASK		(1 << 28)  /* Transmitter enable */
#define XTE_TXC_TXVLAN_MASK		(1 << 27)  /* VLAN enable */
#define XTE_TXC_TXHD_MASK		(1 << 26)  /* Half duplex */

#define XTE_FCC_OFFSET			0x000002C0 /* Flow control config */
#define XTE_FCC_RXFLO_MASK		(1 << 29)  /* Rx flow control enable */
#define XTE_FCC_TXFLO_MASK		(1 << 30)  /* Tx flow control enable */

#define XTE_EMCFG_OFFSET		0x00000300 /* EMAC configuration */
#define XTE_EMCFG_LINKSPD_MASK		0xC0000000 /* Link speed */
#define XTE_EMCFG_HOSTEN_MASK		(1 << 26)  /* Host interface enable */
#define XTE_EMCFG_LINKSPD_10		0x00000000 /* 10 Mbit LINKSPD_MASK */
#define XTE_EMCFG_LINKSPD_100		(1 << 30)  /* 100 Mbit LINKSPD_MASK */
#define XTE_EMCFG_LINKSPD_1000		(1 << 31)  /* 1000 Mbit LINKSPD_MASK */

#define XTE_GMIC_OFFSET			0x00000320 /* RGMII/SGMII config */
#define XTE_MC_OFFSET			0x00000340 /* MDIO configuration */
#define XTE_UAW0_OFFSET			0x00000380 /* Unicast address word 0 */
#define XTE_UAW1_OFFSET			0x00000384 /* Unicast address word 1 */

#define XTE_MAW0_OFFSET			0x00000388 /* Multicast addr word 0 */
#define XTE_MAW1_OFFSET			0x0000038C /* Multicast addr word 1 */
#define XTE_AFM_OFFSET			0x00000390 /* Promiscuous mode */
#define XTE_AFM_EPPRM_MASK		(1 << 31)  /* Promiscuous mode enable */

/* Interrupt Request status */
#define XTE_TIS_OFFSET			0x000003A0
#define TIS_FRIS			(1 << 0)
#define TIS_MRIS			(1 << 1)
#define TIS_MWIS			(1 << 2)
#define TIS_ARIS			(1 << 3)
#define TIS_AWIS			(1 << 4)
#define TIS_CRIS			(1 << 5)
#define TIS_CWIS			(1 << 6)

#define XTE_TIE_OFFSET			0x000003A4 /* Interrupt enable */

/* MII Management Control register (MGTCR) */
#define XTE_MGTDR_OFFSET		0x000003B0 /* MII data */
#define XTE_MIIMAI_OFFSET		0x000003B4 /* MII control */

#define CNTLREG_WRITE_ENABLE_MASK   0x8000
#define CNTLREG_EMAC1SEL_MASK       0x0400
#define CNTLREG_ADDRESSCODE_MASK    0x03ff

/* CDMAC descriptor status bit definitions */

#define STS_CTRL_APP0_ERR         (1 << 31)
#define STS_CTRL_APP0_IRQONEND    (1 << 30)
/* undocumented */
#define STS_CTRL_APP0_STOPONEND   (1 << 29)
#define STS_CTRL_APP0_CMPLT       (1 << 28)
#define STS_CTRL_APP0_SOP         (1 << 27)
#define STS_CTRL_APP0_EOP         (1 << 26)
#define STS_CTRL_APP0_ENGBUSY     (1 << 25)
/* undocumented */
#define STS_CTRL_APP0_ENGRST      (1 << 24)

#define TX_CONTROL_CALC_CSUM_MASK   1

#define MULTICAST_CAM_TABLE_NUM 4

/* TEMAC Synthesis features */
#define TEMAC_FEATURE_RX_CSUM  (1 << 0)
#define TEMAC_FEATURE_TX_CSUM  (1 << 1)

/* TX/RX CURDESC_PTR points to first descriptor */
/* TX/RX TAILDESC_PTR points to last descriptor in linked list */

/**
 * struct cdmac_bd - LocalLink buffer descriptor format
 *
 * app0 bits:
 *	0    Error
 *	1    IrqOnEnd    generate an interrupt at completion of DMA  op
 *	2    reserved
 *	3    completed   Current descriptor completed
 *	4    SOP         TX - marks first desc/ RX marks first desct
 *	5    EOP         TX marks last desc/RX marks last desc
 *	6    EngBusy     DMA is processing
 *	7    reserved
 *	8:31 application specific
 */
struct cdmac_bd {
	u32 next;	/* Physical address of next buffer descriptor */
	u32 phys;
	u32 len;
	u32 app0;
	u32 app1;	/* TX start << 16 | insert */
	u32 app2;	/* TX csum */
	u32 app3;
	u32 app4;	/* skb for TX length for RX */
};

struct temac_local {
	struct net_device *ndev;
	struct device *dev;

	/* Connection to PHY device */
	struct device_node *phy_node;
	/* For non-device-tree devices */
	char phy_name[MII_BUS_ID_SIZE + 3];
	phy_interface_t phy_interface;

	/* MDIO bus data */
	struct mii_bus *mii_bus;	/* MII bus reference */

	/* IO registers, dma functions and IRQs */
	void __iomem *regs;
	void __iomem *sdma_regs;
#ifdef CONFIG_PPC_DCR
	dcr_host_t sdma_dcrs;
#endif
	u32 (*temac_ior)(struct temac_local *lp, int offset);
	void (*temac_iow)(struct temac_local *lp, int offset, u32 value);
	u32 (*dma_in)(struct temac_local *lp, int reg);
	void (*dma_out)(struct temac_local *lp, int reg, u32 value);

	int tx_irq;
	int rx_irq;
	int emac_num;

	struct sk_buff **rx_skb;
	spinlock_t rx_lock;
	/* For synchronization of indirect register access.  Must be
	 * shared mutex between interfaces in same TEMAC block.
	 */
	spinlock_t *indirect_lock;
	u32 options;			/* Current options word */
	int last_link;
	unsigned int temac_features;

	/* Buffer descriptors */
	struct cdmac_bd *tx_bd_v;
	dma_addr_t tx_bd_p;
	u32 tx_bd_num;
	struct cdmac_bd *rx_bd_v;
	dma_addr_t rx_bd_p;
	u32 rx_bd_num;
	int tx_bd_ci;
	int tx_bd_tail;
	int rx_bd_ci;
	int rx_bd_tail;

	/* DMA channel control setup */
	u8 coalesce_count_tx;
	u8 coalesce_delay_tx;
	u8 coalesce_count_rx;
	u8 coalesce_delay_rx;

	struct delayed_work restart_work;
};

/* Wrappers for temac_ior()/temac_iow() function pointers above */
#define temac_ior(lp, o) ((lp)->temac_ior(lp, o))
#define temac_iow(lp, o, v) ((lp)->temac_iow(lp, o, v))

/* xilinx_temac.c */
int temac_indirect_busywait(struct temac_local *lp);
u32 temac_indirect_in32(struct temac_local *lp, int reg);
u32 temac_indirect_in32_locked(struct temac_local *lp, int reg);
void temac_indirect_out32(struct temac_local *lp, int reg, u32 value);
void temac_indirect_out32_locked(struct temac_local *lp, int reg, u32 value);

/* xilinx_temac_mdio.c */
int temac_mdio_setup(struct temac_local *lp, struct platform_device *pdev);
void temac_mdio_teardown(struct temac_local *lp);

#endif /* XILINX_LL_TEMAC_H */