* Qualcomm Atheros QCA8xxx switch family

Required properties:

- compatible: should be one of:
    "qca,qca8327"
    "qca,qca8334"
    "qca,qca8337"

- #size-cells: must be 0
- #address-cells: must be 1

Optional properties:

- reset-gpios: GPIO to be used to reset the whole device

Subnodes:

The integrated switch subnode should be specified according to the binding
described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
mdio-bus each subnode describing a port needs to have a valid phandle
referencing the internal PHY it is connected to. This is because there's no
N:N mapping of port and PHY id.
To declare the internal mdio-bus configuration, declare a mdio node in the
switch node and declare the phandle for the port referencing the internal
PHY is connected to. In this config a internal mdio-bus is registered and
the mdio MASTER is used as communication.

Don't use mixed external and internal mdio-bus configurations, as this is
not supported by the hardware.

The CPU port of this switch is always port 0.

A CPU port node has the following optional node:

- fixed-link            : Fixed-link subnode describing a link to a non-MDIO
                          managed entity. See
                          Documentation/devicetree/bindings/net/fixed-link.txt
                          for details.

For QCA8K the 'fixed-link' sub-node supports only the following properties:

- 'speed' (integer, mandatory), to indicate the link speed. Accepted
  values are 10, 100 and 1000
- 'full-duplex' (boolean, optional), to indicate that full duplex is
  used. When absent, half duplex is assumed.

Examples:

for the external mdio-bus configuration:

	&mdio0 {
		phy_port1: phy@0 {
			reg = <0>;
		};

		phy_port2: phy@1 {
			reg = <1>;
		};

		phy_port3: phy@2 {
			reg = <2>;
		};

		phy_port4: phy@3 {
			reg = <3>;
		};

		phy_port5: phy@4 {
			reg = <4>;
		};

		switch@10 {
			compatible = "qca,qca8337";
			#address-cells = <1>;
			#size-cells = <0>;

			reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
			reg = <0x10>;

			ports {
				#address-cells = <1>;
				#size-cells = <0>;
				port@0 {
					reg = <0>;
					label = "cpu";
					ethernet = <&gmac1>;
					phy-mode = "rgmii";
					fixed-link {
						speed = 1000;
						full-duplex;
					};
				};

				port@1 {
					reg = <1>;
					label = "lan1";
					phy-handle = <&phy_port1>;
				};

				port@2 {
					reg = <2>;
					label = "lan2";
					phy-handle = <&phy_port2>;
				};

				port@3 {
					reg = <3>;
					label = "lan3";
					phy-handle = <&phy_port3>;
				};

				port@4 {
					reg = <4>;
					label = "lan4";
					phy-handle = <&phy_port4>;
				};

				port@5 {
					reg = <5>;
					label = "wan";
					phy-handle = <&phy_port5>;
				};
			};
		};
	};

for the internal master mdio-bus configuration:

	&mdio0 {
		switch@10 {
			compatible = "qca,qca8337";
			#address-cells = <1>;
			#size-cells = <0>;

			reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
			reg = <0x10>;

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					label = "cpu";
					ethernet = <&gmac1>;
					phy-mode = "rgmii";
					fixed-link {
						speed = 1000;
						full-duplex;
					};
				};

				port@1 {
					reg = <1>;
					label = "lan1";
					phy-mode = "internal";
					phy-handle = <&phy_port1>;
				};

				port@2 {
					reg = <2>;
					label = "lan2";
					phy-mode = "internal";
					phy-handle = <&phy_port2>;
				};

				port@3 {
					reg = <3>;
					label = "lan3";
					phy-mode = "internal";
					phy-handle = <&phy_port3>;
				};

				port@4 {
					reg = <4>;
					label = "lan4";
					phy-mode = "internal";
					phy-handle = <&phy_port4>;
				};

				port@5 {
					reg = <5>;
					label = "wan";
					phy-mode = "internal";
					phy-handle = <&phy_port5>;
				};
			};

			mdio {
				#address-cells = <1>;
				#size-cells = <0>;

				phy_port1: phy@0 {
					reg = <0>;
				};

				phy_port2: phy@1 {
					reg = <1>;
				};

				phy_port3: phy@2 {
					reg = <2>;
				};

				phy_port4: phy@3 {
					reg = <3>;
				};

				phy_port5: phy@4 {
					reg = <4>;
				};
			};
		};
	};