mfd: Refactor DB8500 PRCMU reg access
Instead of carrying around the __PRCMU_BASE in every read or
write to the PRCMU registers, move it out to the register
definition file and define registers along with their base
offset so that the code gets easier to read.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 02a15d7..b5bd245 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -412,7 +412,7 @@
static DEFINE_SPINLOCK(clk_mgt_lock);
-#define CLK_MGT_ENTRY(_name)[PRCMU_##_name] = { (PRCM_##_name##_MGT), 0 }
+#define CLK_MGT_ENTRY(_name)[PRCMU_##_name] = { (PRCM_##_name##_MGT_OFF), 0 }
struct clk_mgt clk_mgt[PRCMU_NUM_REG_CLOCKS] = {
CLK_MGT_ENTRY(SGACLK),
CLK_MGT_ENTRY(UARTCLK),
@@ -499,45 +499,41 @@
unsigned int plldsifreq;
/* Clear DSIPLL_RESETN */
- writel(PRCMU_RESET_DSIPLL, (_PRCMU_BASE + PRCM_APE_RESETN_CLR));
+ writel(PRCMU_RESET_DSIPLL, PRCM_APE_RESETN_CLR);
/* Unclamp DSIPLL in/out */
- writel(PRCMU_UNCLAMP_DSIPLL, (_PRCMU_BASE + PRCM_MMIP_LS_CLAMP_CLR));
+ writel(PRCMU_UNCLAMP_DSIPLL, PRCM_MMIP_LS_CLAMP_CLR);
if (prcmu_is_u8400())
plldsifreq = PRCMU_PLLDSI_FREQ_SETTING_U8400;
else
plldsifreq = PRCMU_PLLDSI_FREQ_SETTING;
/* Set DSI PLL FREQ */
- writel(plldsifreq, (_PRCMU_BASE + PRCM_PLLDSI_FREQ));
- writel(PRCMU_DSI_PLLOUT_SEL_SETTING,
- (_PRCMU_BASE + PRCM_DSI_PLLOUT_SEL));
+ writel(plldsifreq, PRCM_PLLDSI_FREQ);
+ writel(PRCMU_DSI_PLLOUT_SEL_SETTING, PRCM_DSI_PLLOUT_SEL);
/* Enable Escape clocks */
- writel(PRCMU_ENABLE_ESCAPE_CLOCK_DIV,
- (_PRCMU_BASE + PRCM_DSITVCLK_DIV));
+ writel(PRCMU_ENABLE_ESCAPE_CLOCK_DIV, PRCM_DSITVCLK_DIV);
/* Start DSI PLL */
- writel(PRCMU_ENABLE_PLLDSI, (_PRCMU_BASE + PRCM_PLLDSI_ENABLE));
+ writel(PRCMU_ENABLE_PLLDSI, PRCM_PLLDSI_ENABLE);
/* Reset DSI PLL */
- writel(PRCMU_DSI_RESET_SW, (_PRCMU_BASE + PRCM_DSI_SW_RESET));
+ writel(PRCMU_DSI_RESET_SW, PRCM_DSI_SW_RESET);
for (i = 0; i < 10; i++) {
- if ((readl(_PRCMU_BASE + PRCM_PLLDSI_LOCKP) &
- PRCMU_PLLDSI_LOCKP_LOCKED)
+ if ((readl(PRCM_PLLDSI_LOCKP) & PRCMU_PLLDSI_LOCKP_LOCKED)
== PRCMU_PLLDSI_LOCKP_LOCKED)
break;
udelay(100);
}
/* Set DSIPLL_RESETN */
- writel(PRCMU_RESET_DSIPLL, (_PRCMU_BASE + PRCM_APE_RESETN_SET));
+ writel(PRCMU_RESET_DSIPLL, PRCM_APE_RESETN_SET);
return 0;
}
int prcmu_disable_dsipll(void)
{
/* Disable dsi pll */
- writel(PRCMU_DISABLE_PLLDSI, (_PRCMU_BASE + PRCM_PLLDSI_ENABLE));
+ writel(PRCMU_DISABLE_PLLDSI, PRCM_PLLDSI_ENABLE);
/* Disable escapeclock */
- writel(PRCMU_DISABLE_ESCAPE_CLOCK_DIV,
- (_PRCMU_BASE + PRCM_DSITVCLK_DIV));
+ writel(PRCMU_DISABLE_ESCAPE_CLOCK_DIV, PRCM_DSITVCLK_DIV);
return 0;
}
@@ -554,15 +550,15 @@
spin_lock_irqsave(&clk_mgt_lock, flags);
/* Grab the HW semaphore. */
- while ((readl(_PRCMU_BASE + PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
+ while ((readl(PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
cpu_relax();
- writel(dsiclk, (_PRCMU_BASE + PRCM_HDMICLK_MGT));
- writel(PRCMU_DSI_LP_CLOCK_SETTING, (_PRCMU_BASE + PRCM_TVCLK_MGT));
- writel(PRCMU_DPI_CLOCK_SETTING, (_PRCMU_BASE + PRCM_LCDCLK_MGT));
+ writel(dsiclk, PRCM_HDMICLK_MGT);
+ writel(PRCMU_DSI_LP_CLOCK_SETTING, PRCM_TVCLK_MGT);
+ writel(PRCMU_DPI_CLOCK_SETTING, PRCM_LCDCLK_MGT);
/* Release the HW semaphore. */
- writel(0, (_PRCMU_BASE + PRCM_SEM));
+ writel(0, PRCM_SEM);
spin_unlock_irqrestore(&clk_mgt_lock, flags);
@@ -578,8 +574,8 @@
unsigned long flags;
spin_lock_irqsave(&gpiocr_lock, flags);
- reg = readl(_PRCMU_BASE + PRCM_GPIOCR);
- writel(reg | PRCM_GPIOCR_SPI2_SELECT, _PRCMU_BASE + PRCM_GPIOCR);
+ reg = readl(PRCM_GPIOCR);
+ writel(reg | PRCM_GPIOCR_SPI2_SELECT, PRCM_GPIOCR);
spin_unlock_irqrestore(&gpiocr_lock, flags);
}
@@ -592,8 +588,8 @@
unsigned long flags;
spin_lock_irqsave(&gpiocr_lock, flags);
- reg = readl(_PRCMU_BASE + PRCM_GPIOCR);
- writel(reg & ~PRCM_GPIOCR_SPI2_SELECT, _PRCMU_BASE + PRCM_GPIOCR);
+ reg = readl(PRCM_GPIOCR);
+ writel(reg & ~PRCM_GPIOCR_SPI2_SELECT, PRCM_GPIOCR);
spin_unlock_irqrestore(&gpiocr_lock, flags);
}
@@ -701,7 +697,7 @@
spin_lock_irqsave(&clkout_lock, flags);
- val = readl(_PRCMU_BASE + PRCM_CLKOCR);
+ val = readl(PRCM_CLKOCR);
if (val & div_mask) {
if (div) {
if ((val & mask) != bits) {
@@ -715,7 +711,7 @@
}
}
}
- writel((bits | (val & ~mask)), (_PRCMU_BASE + PRCM_CLKOCR));
+ writel((bits | (val & ~mask)), PRCM_CLKOCR);
requests[clkout] += (div ? 1 : -1);
unlock_and_return:
@@ -732,7 +728,7 @@
spin_lock_irqsave(&mb0_transfer.lock, flags);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
cpu_relax();
writeb(MB0H_POWER_STATE_TRANS, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB0));
@@ -741,7 +737,7 @@
writeb((keep_ulp_clk ? 1 : 0),
(tcdm_base + PRCM_REQ_MB0_ULP_CLOCK_STATE));
writeb(0, (tcdm_base + PRCM_REQ_MB0_DO_NOT_WFI));
- writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(0), PRCM_MBOX_CPU_SET);
spin_unlock_irqrestore(&mb0_transfer.lock, flags);
@@ -770,12 +766,12 @@
return;
for (i = 0; i < 2; i++) {
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
cpu_relax();
writel(dbb_events, (tcdm_base + PRCM_REQ_MB0_WAKEUP_8500));
writel(abb_events, (tcdm_base + PRCM_REQ_MB0_WAKEUP_4500));
writeb(header[i], (tcdm_base + PRCM_MBOX_HEADER_REQ_MB0));
- writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(0), PRCM_MBOX_CPU_SET);
}
last_dbb_events = dbb_events;
last_abb_events = abb_events;
@@ -840,14 +836,14 @@
mutex_lock(&mb1_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
cpu_relax();
writeb(MB1H_ARM_APE_OPP, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
writeb(opp, (tcdm_base + PRCM_REQ_MB1_ARM_OPP));
writeb(APE_NO_CHANGE, (tcdm_base + PRCM_REQ_MB1_APE_OPP));
- writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(1), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb1_transfer.work);
if ((mb1_transfer.ack.header != MB1H_ARM_APE_OPP) ||
@@ -876,7 +872,7 @@
*/
int prcmu_get_ddr_opp(void)
{
- return readb(_PRCMU_BASE + PRCM_DDR_SUBSYS_APE_MINBW);
+ return readb(PRCM_DDR_SUBSYS_APE_MINBW);
}
/**
@@ -892,7 +888,7 @@
return -EINVAL;
/* Changing the DDR OPP can hang the hardware pre-v21 */
if (cpu_is_u8500v20_or_later() && !cpu_is_u8500v20())
- writeb(opp, (_PRCMU_BASE + PRCM_DDR_SUBSYS_APE_MINBW));
+ writeb(opp, PRCM_DDR_SUBSYS_APE_MINBW);
return 0;
}
@@ -909,14 +905,14 @@
mutex_lock(&mb1_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
cpu_relax();
writeb(MB1H_ARM_APE_OPP, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
writeb(ARM_NO_CHANGE, (tcdm_base + PRCM_REQ_MB1_ARM_OPP));
writeb(opp, (tcdm_base + PRCM_REQ_MB1_APE_OPP));
- writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(1), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb1_transfer.work);
if ((mb1_transfer.ack.header != MB1H_ARM_APE_OPP) ||
@@ -966,12 +962,12 @@
header = MB1H_RELEASE_APE_OPP_100_VOLT;
}
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
cpu_relax();
writeb(header, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
- writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(1), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb1_transfer.work);
if ((mb1_transfer.ack.header != header) ||
@@ -995,13 +991,13 @@
mutex_lock(&mb1_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
cpu_relax();
writeb(MB1H_RELEASE_USB_WAKEUP,
(tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
- writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(1), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb1_transfer.work);
if ((mb1_transfer.ack.header != MB1H_RELEASE_USB_WAKEUP) ||
@@ -1048,7 +1044,7 @@
mutex_lock(&mb2_transfer.lock);
/* wait for mailbox */
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(2))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(2))
cpu_relax();
/* fill in mailbox */
@@ -1058,7 +1054,7 @@
writeb(MB2H_DPS, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB2));
- writel(MBOX_BIT(2), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(2), PRCM_MBOX_CPU_SET);
/*
* The current firmware version does not handle errors correctly,
@@ -1145,13 +1141,13 @@
spin_lock_irqsave(&mb3_transfer.lock, flags);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(3))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(3))
cpu_relax();
writeb((enable ? ON : OFF), (tcdm_base + PRCM_REQ_MB3_SYSCLK_MGT));
writeb(MB3H_SYSCLK, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB3));
- writel(MBOX_BIT(3), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(3), PRCM_MBOX_CPU_SET);
spin_unlock_irqrestore(&mb3_transfer.lock, flags);
@@ -1177,7 +1173,7 @@
if (!enable)
val |= PRCM_TCR_STOP_TIMERS;
- writel(val, (_PRCMU_BASE + PRCM_TCR));
+ writel(val, PRCM_TCR);
return 0;
}
@@ -1190,7 +1186,7 @@
spin_lock_irqsave(&clk_mgt_lock, flags);
/* Grab the HW semaphore. */
- while ((readl(_PRCMU_BASE + PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
+ while ((readl(PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
cpu_relax();
val = readl(_PRCMU_BASE + clk_mgt[clock].offset);
@@ -1203,7 +1199,7 @@
writel(val, (_PRCMU_BASE + clk_mgt[clock].offset));
/* Release the HW semaphore. */
- writel(0, (_PRCMU_BASE + PRCM_SEM));
+ writel(0, PRCM_SEM);
spin_unlock_irqrestore(&clk_mgt_lock, flags);
@@ -1238,7 +1234,7 @@
mutex_lock(&mb4_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
cpu_relax();
writeb(MB4H_MEM_ST, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
@@ -1248,7 +1244,7 @@
(tcdm_base + PRCM_REQ_MB4_DDR_ST_AP_DEEP_IDLE));
writeb(state, (tcdm_base + PRCM_REQ_MB4_ESRAM0_ST));
- writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(4), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb4_transfer.work);
mutex_unlock(&mb4_transfer.lock);
@@ -1260,13 +1256,13 @@
{
mutex_lock(&mb4_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
cpu_relax();
writeb(threshold, (tcdm_base + PRCM_REQ_MB4_HOTDOG_THRESHOLD));
writeb(MB4H_HOTDOG, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
- writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(4), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb4_transfer.work);
mutex_unlock(&mb4_transfer.lock);
@@ -1278,7 +1274,7 @@
{
mutex_lock(&mb4_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
cpu_relax();
writeb(low, (tcdm_base + PRCM_REQ_MB4_HOTMON_LOW));
@@ -1287,7 +1283,7 @@
(tcdm_base + PRCM_REQ_MB4_HOTMON_CONFIG));
writeb(MB4H_HOTMON, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
- writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(4), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb4_transfer.work);
mutex_unlock(&mb4_transfer.lock);
@@ -1299,13 +1295,13 @@
{
mutex_lock(&mb4_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(4))
cpu_relax();
writew(val, (tcdm_base + PRCM_REQ_MB4_HOT_PERIOD));
writeb(MB4H_HOT_PERIOD, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB4));
- writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(4), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb4_transfer.work);
mutex_unlock(&mb4_transfer.lock);
@@ -1345,7 +1341,7 @@
spin_lock_irqsave(&clk_mgt_lock, flags);
/* Grab the HW semaphore. */
- while ((readl(_PRCMU_BASE + PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
+ while ((readl(PRCM_SEM) & PRCM_SEM_PRCM_SEM) != 0)
cpu_relax();
val = readl(_PRCMU_BASE + clk_mgt[clock].offset);
@@ -1354,7 +1350,7 @@
writel(val, (_PRCMU_BASE + clk_mgt[clock].offset));
/* Release the HW semaphore. */
- writel(0, (_PRCMU_BASE + PRCM_SEM));
+ writel(0, PRCM_SEM);
spin_unlock_irqrestore(&clk_mgt_lock, flags);
@@ -1380,7 +1376,7 @@
mutex_lock(&mb5_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
cpu_relax();
writeb(PRCMU_I2C_READ(slave), (tcdm_base + PRCM_REQ_MB5_I2C_SLAVE_OP));
@@ -1388,7 +1384,7 @@
writeb(reg, (tcdm_base + PRCM_REQ_MB5_I2C_REG));
writeb(0, (tcdm_base + PRCM_REQ_MB5_I2C_VAL));
- writel(MBOX_BIT(5), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(5), PRCM_MBOX_CPU_SET);
if (!wait_for_completion_timeout(&mb5_transfer.work,
msecs_to_jiffies(20000))) {
@@ -1426,7 +1422,7 @@
mutex_lock(&mb5_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
cpu_relax();
writeb(PRCMU_I2C_WRITE(slave), (tcdm_base + PRCM_REQ_MB5_I2C_SLAVE_OP));
@@ -1434,7 +1430,7 @@
writeb(reg, (tcdm_base + PRCM_REQ_MB5_I2C_REG));
writeb(*value, (tcdm_base + PRCM_REQ_MB5_I2C_VAL));
- writel(MBOX_BIT(5), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(5), PRCM_MBOX_CPU_SET);
if (!wait_for_completion_timeout(&mb5_transfer.work,
msecs_to_jiffies(20000))) {
@@ -1459,14 +1455,13 @@
mutex_lock(&mb0_transfer.ac_wake_lock);
- val = readl(_PRCMU_BASE + PRCM_HOSTACCESS_REQ);
+ val = readl(PRCM_HOSTACCESS_REQ);
if (val & PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ)
goto unlock_and_return;
atomic_set(&ac_wake_req_state, 1);
- writel((val | PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ),
- (_PRCMU_BASE + PRCM_HOSTACCESS_REQ));
+ writel((val | PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ), PRCM_HOSTACCESS_REQ);
if (!wait_for_completion_timeout(&mb0_transfer.ac_wake_work,
msecs_to_jiffies(20000))) {
@@ -1487,12 +1482,12 @@
mutex_lock(&mb0_transfer.ac_wake_lock);
- val = readl(_PRCMU_BASE + PRCM_HOSTACCESS_REQ);
+ val = readl(PRCM_HOSTACCESS_REQ);
if (!(val & PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ))
goto unlock_and_return;
writel((val & ~PRCM_HOSTACCESS_REQ_HOSTACCESS_REQ),
- (_PRCMU_BASE + PRCM_HOSTACCESS_REQ));
+ PRCM_HOSTACCESS_REQ);
if (!wait_for_completion_timeout(&mb0_transfer.ac_wake_work,
msecs_to_jiffies(20000))) {
@@ -1520,7 +1515,7 @@
void prcmu_system_reset(u16 reset_code)
{
writew(reset_code, (tcdm_base + PRCM_SW_RST_REASON));
- writel(1, (_PRCMU_BASE + PRCM_APE_SOFTRST));
+ writel(1, PRCM_APE_SOFTRST);
}
/**
@@ -1530,11 +1525,11 @@
{
mutex_lock(&mb1_transfer.lock);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(1))
cpu_relax();
writeb(MB1H_RESET_MODEM, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB1));
- writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(1), PRCM_MBOX_CPU_SET);
wait_for_completion(&mb1_transfer.work);
/*
@@ -1551,11 +1546,11 @@
spin_lock_irqsave(&mb0_transfer.lock, flags);
- while (readl(_PRCMU_BASE + PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
cpu_relax();
writeb(MB0H_READ_WAKEUP_ACK, (tcdm_base + PRCM_MBOX_HEADER_REQ_MB0));
- writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_MBOX_CPU_SET));
+ writel(MBOX_BIT(0), PRCM_MBOX_CPU_SET);
spin_unlock_irqrestore(&mb0_transfer.lock, flags);
}
@@ -1600,7 +1595,7 @@
r = false;
break;
}
- writel(MBOX_BIT(0), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(0), PRCM_ARM_IT1_CLR);
return r;
}
@@ -1613,7 +1608,7 @@
PRCM_ACK_MB1_CURRENT_APE_OPP);
mb1_transfer.ack.ape_voltage_status = readb(tcdm_base +
PRCM_ACK_MB1_APE_VOLTAGE_STATUS);
- writel(MBOX_BIT(1), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(1), PRCM_ARM_IT1_CLR);
complete(&mb1_transfer.work);
return false;
}
@@ -1621,14 +1616,14 @@
static bool read_mailbox_2(void)
{
mb2_transfer.ack.status = readb(tcdm_base + PRCM_ACK_MB2_DPS_STATUS);
- writel(MBOX_BIT(2), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(2), PRCM_ARM_IT1_CLR);
complete(&mb2_transfer.work);
return false;
}
static bool read_mailbox_3(void)
{
- writel(MBOX_BIT(3), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(3), PRCM_ARM_IT1_CLR);
return false;
}
@@ -1650,7 +1645,7 @@
break;
}
- writel(MBOX_BIT(4), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(4), PRCM_ARM_IT1_CLR);
if (do_complete)
complete(&mb4_transfer.work);
@@ -1662,20 +1657,20 @@
{
mb5_transfer.ack.status = readb(tcdm_base + PRCM_ACK_MB5_I2C_STATUS);
mb5_transfer.ack.value = readb(tcdm_base + PRCM_ACK_MB5_I2C_VAL);
- writel(MBOX_BIT(5), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(5), PRCM_ARM_IT1_CLR);
complete(&mb5_transfer.work);
return false;
}
static bool read_mailbox_6(void)
{
- writel(MBOX_BIT(6), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(6), PRCM_ARM_IT1_CLR);
return false;
}
static bool read_mailbox_7(void)
{
- writel(MBOX_BIT(7), (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(MBOX_BIT(7), PRCM_ARM_IT1_CLR);
return false;
}
@@ -1696,7 +1691,7 @@
u8 n;
irqreturn_t r;
- bits = (readl(_PRCMU_BASE + PRCM_ARM_IT1_VAL) & ALL_MBOX_BITS);
+ bits = (readl(PRCM_ARM_IT1_VAL) & ALL_MBOX_BITS);
if (unlikely(!bits))
return IRQ_NONE;
@@ -2025,7 +2020,7 @@
return -ENODEV;
/* Clean up the mailbox interrupts after pre-kernel code. */
- writel(ALL_MBOX_BITS, (_PRCMU_BASE + PRCM_ARM_IT1_CLR));
+ writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLR);
err = request_threaded_irq(IRQ_DB8500_PRCMU1, prcmu_irq_handler,
prcmu_irq_thread_fn, IRQF_NO_SUSPEND, "prcmu", NULL);
