| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Support for LGDT3306A - 8VSB/QAM-B |
| * |
| * Copyright (C) 2013 Fred Richter <frichter@hauppauge.com> |
| * - driver structure based on lgdt3305.[ch] by Michael Krufky |
| * - code based on LG3306_V0.35 API by LG Electronics Inc. |
| */ |
| |
| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| |
| #include <asm/div64.h> |
| #include <linux/kernel.h> |
| #include <linux/dvb/frontend.h> |
| #include <linux/int_log.h> |
| #include "lgdt3306a.h" |
| #include <linux/i2c-mux.h> |
| |
| |
| static int debug; |
| module_param(debug, int, 0644); |
| MODULE_PARM_DESC(debug, "set debug level (info=1, reg=2 (or-able))"); |
| |
| /* |
| * Older drivers treated QAM64 and QAM256 the same; that is the HW always |
| * used "Auto" mode during detection. Setting "forced_manual"=1 allows |
| * the user to treat these modes as separate. For backwards compatibility, |
| * it's off by default. QAM_AUTO can now be specified to achive that |
| * effect even if "forced_manual"=1 |
| */ |
| static int forced_manual; |
| module_param(forced_manual, int, 0644); |
| MODULE_PARM_DESC(forced_manual, "if set, QAM64 and QAM256 will only lock to modulation specified"); |
| |
| #define DBG_INFO 1 |
| #define DBG_REG 2 |
| #define DBG_DUMP 4 /* FGR - comment out to remove dump code */ |
| |
| #define lg_debug(fmt, arg...) \ |
| printk(KERN_DEBUG pr_fmt(fmt), ## arg) |
| |
| #define dbg_info(fmt, arg...) \ |
| do { \ |
| if (debug & DBG_INFO) \ |
| lg_debug(fmt, ## arg); \ |
| } while (0) |
| |
| #define dbg_reg(fmt, arg...) \ |
| do { \ |
| if (debug & DBG_REG) \ |
| lg_debug(fmt, ## arg); \ |
| } while (0) |
| |
| #define lg_chkerr(ret) \ |
| ({ \ |
| int __ret; \ |
| __ret = (ret < 0); \ |
| if (__ret) \ |
| pr_err("error %d on line %d\n", ret, __LINE__); \ |
| __ret; \ |
| }) |
| |
| struct lgdt3306a_state { |
| struct i2c_adapter *i2c_adap; |
| const struct lgdt3306a_config *cfg; |
| |
| struct dvb_frontend frontend; |
| |
| enum fe_modulation current_modulation; |
| u32 current_frequency; |
| u32 snr; |
| |
| struct i2c_mux_core *muxc; |
| }; |
| |
| /* |
| * LG3306A Register Usage |
| * (LG does not really name the registers, so this code does not either) |
| * |
| * 0000 -> 00FF Common control and status |
| * 1000 -> 10FF Synchronizer control and status |
| * 1F00 -> 1FFF Smart Antenna control and status |
| * 2100 -> 21FF VSB Equalizer control and status |
| * 2800 -> 28FF QAM Equalizer control and status |
| * 3000 -> 30FF FEC control and status |
| */ |
| |
| enum lgdt3306a_lock_status { |
| LG3306_UNLOCK = 0x00, |
| LG3306_LOCK = 0x01, |
| LG3306_UNKNOWN_LOCK = 0xff |
| }; |
| |
| enum lgdt3306a_neverlock_status { |
| LG3306_NL_INIT = 0x00, |
| LG3306_NL_PROCESS = 0x01, |
| LG3306_NL_LOCK = 0x02, |
| LG3306_NL_FAIL = 0x03, |
| LG3306_NL_UNKNOWN = 0xff |
| }; |
| |
| enum lgdt3306a_modulation { |
| LG3306_VSB = 0x00, |
| LG3306_QAM64 = 0x01, |
| LG3306_QAM256 = 0x02, |
| LG3306_UNKNOWN_MODE = 0xff |
| }; |
| |
| enum lgdt3306a_lock_check { |
| LG3306_SYNC_LOCK, |
| LG3306_FEC_LOCK, |
| LG3306_TR_LOCK, |
| LG3306_AGC_LOCK, |
| }; |
| |
| |
| #ifdef DBG_DUMP |
| static void lgdt3306a_DumpAllRegs(struct lgdt3306a_state *state); |
| static void lgdt3306a_DumpRegs(struct lgdt3306a_state *state); |
| #endif |
| |
| |
| static int lgdt3306a_write_reg(struct lgdt3306a_state *state, u16 reg, u8 val) |
| { |
| int ret; |
| u8 buf[] = { reg >> 8, reg & 0xff, val }; |
| struct i2c_msg msg = { |
| .addr = state->cfg->i2c_addr, .flags = 0, |
| .buf = buf, .len = 3, |
| }; |
| |
| dbg_reg("reg: 0x%04x, val: 0x%02x\n", reg, val); |
| |
| ret = i2c_transfer(state->i2c_adap, &msg, 1); |
| |
| if (ret != 1) { |
| pr_err("error (addr %02x %02x <- %02x, err = %i)\n", |
| msg.buf[0], msg.buf[1], msg.buf[2], ret); |
| if (ret < 0) |
| return ret; |
| else |
| return -EREMOTEIO; |
| } |
| return 0; |
| } |
| |
| static int lgdt3306a_read_reg(struct lgdt3306a_state *state, u16 reg, u8 *val) |
| { |
| int ret; |
| u8 reg_buf[] = { reg >> 8, reg & 0xff }; |
| struct i2c_msg msg[] = { |
| { .addr = state->cfg->i2c_addr, |
| .flags = 0, .buf = reg_buf, .len = 2 }, |
| { .addr = state->cfg->i2c_addr, |
| .flags = I2C_M_RD, .buf = val, .len = 1 }, |
| }; |
| |
| ret = i2c_transfer(state->i2c_adap, msg, 2); |
| |
| if (ret != 2) { |
| pr_err("error (addr %02x reg %04x error (ret == %i)\n", |
| state->cfg->i2c_addr, reg, ret); |
| if (ret < 0) |
| return ret; |
| else |
| return -EREMOTEIO; |
| } |
| dbg_reg("reg: 0x%04x, val: 0x%02x\n", reg, *val); |
| |
| return 0; |
| } |
| |
| #define read_reg(state, reg) \ |
| ({ \ |
| u8 __val; \ |
| int ret = lgdt3306a_read_reg(state, reg, &__val); \ |
| if (lg_chkerr(ret)) \ |
| __val = 0; \ |
| __val; \ |
| }) |
| |
| static int lgdt3306a_set_reg_bit(struct lgdt3306a_state *state, |
| u16 reg, int bit, int onoff) |
| { |
| u8 val; |
| int ret; |
| |
| dbg_reg("reg: 0x%04x, bit: %d, level: %d\n", reg, bit, onoff); |
| |
| ret = lgdt3306a_read_reg(state, reg, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| val &= ~(1 << bit); |
| val |= (onoff & 1) << bit; |
| |
| ret = lgdt3306a_write_reg(state, reg, val); |
| lg_chkerr(ret); |
| fail: |
| return ret; |
| } |
| |
| /* ------------------------------------------------------------------------ */ |
| |
| static int lgdt3306a_soft_reset(struct lgdt3306a_state *state) |
| { |
| int ret; |
| |
| dbg_info("\n"); |
| |
| ret = lgdt3306a_set_reg_bit(state, 0x0000, 7, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| msleep(20); |
| ret = lgdt3306a_set_reg_bit(state, 0x0000, 7, 1); |
| lg_chkerr(ret); |
| |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_mpeg_mode(struct lgdt3306a_state *state, |
| enum lgdt3306a_mpeg_mode mode) |
| { |
| u8 val; |
| int ret; |
| |
| dbg_info("(%d)\n", mode); |
| /* transport packet format - TPSENB=0x80 */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0071, 7, |
| mode == LGDT3306A_MPEG_PARALLEL ? 1 : 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* |
| * start of packet signal duration |
| * TPSSOPBITEN=0x40; 0=byte duration, 1=bit duration |
| */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0071, 6, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_read_reg(state, 0x0070, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| val |= 0x10; /* TPCLKSUPB=0x10 */ |
| |
| if (mode == LGDT3306A_MPEG_PARALLEL) |
| val &= ~0x10; |
| |
| ret = lgdt3306a_write_reg(state, 0x0070, val); |
| lg_chkerr(ret); |
| |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_mpeg_mode_polarity(struct lgdt3306a_state *state, |
| enum lgdt3306a_tp_clock_edge edge, |
| enum lgdt3306a_tp_valid_polarity valid) |
| { |
| u8 val; |
| int ret; |
| |
| dbg_info("edge=%d, valid=%d\n", edge, valid); |
| |
| ret = lgdt3306a_read_reg(state, 0x0070, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| val &= ~0x06; /* TPCLKPOL=0x04, TPVALPOL=0x02 */ |
| |
| if (edge == LGDT3306A_TPCLK_RISING_EDGE) |
| val |= 0x04; |
| if (valid == LGDT3306A_TP_VALID_HIGH) |
| val |= 0x02; |
| |
| ret = lgdt3306a_write_reg(state, 0x0070, val); |
| lg_chkerr(ret); |
| |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_mpeg_tristate(struct lgdt3306a_state *state, |
| int mode) |
| { |
| u8 val; |
| int ret; |
| |
| dbg_info("(%d)\n", mode); |
| |
| if (mode) { |
| ret = lgdt3306a_read_reg(state, 0x0070, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| /* |
| * Tristate bus; TPOUTEN=0x80, TPCLKOUTEN=0x20, |
| * TPDATAOUTEN=0x08 |
| */ |
| val &= ~0xa8; |
| ret = lgdt3306a_write_reg(state, 0x0070, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* AGCIFOUTENB=0x40; 1=Disable IFAGC pin */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0003, 6, 1); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| } else { |
| /* enable IFAGC pin */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0003, 6, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_read_reg(state, 0x0070, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| val |= 0xa8; /* enable bus */ |
| ret = lgdt3306a_write_reg(state, 0x0070, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| } |
| |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_ts_bus_ctrl(struct dvb_frontend *fe, int acquire) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| dbg_info("acquire=%d\n", acquire); |
| |
| return lgdt3306a_mpeg_tristate(state, acquire ? 0 : 1); |
| |
| } |
| |
| static int lgdt3306a_power(struct lgdt3306a_state *state, |
| int mode) |
| { |
| int ret; |
| |
| dbg_info("(%d)\n", mode); |
| |
| if (mode == 0) { |
| /* into reset */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0000, 7, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* power down */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0000, 0, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| } else { |
| /* out of reset */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0000, 7, 1); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* power up */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0000, 0, 1); |
| if (lg_chkerr(ret)) |
| goto fail; |
| } |
| |
| #ifdef DBG_DUMP |
| lgdt3306a_DumpAllRegs(state); |
| #endif |
| fail: |
| return ret; |
| } |
| |
| |
| static int lgdt3306a_set_vsb(struct lgdt3306a_state *state) |
| { |
| u8 val; |
| int ret; |
| |
| dbg_info("\n"); |
| |
| /* 0. Spectrum inversion detection manual; spectrum inverted */ |
| ret = lgdt3306a_read_reg(state, 0x0002, &val); |
| val &= 0xf7; /* SPECINVAUTO Off */ |
| val |= 0x04; /* SPECINV On */ |
| ret = lgdt3306a_write_reg(state, 0x0002, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 1. Selection of standard mode(0x08=QAM, 0x80=VSB) */ |
| ret = lgdt3306a_write_reg(state, 0x0008, 0x80); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 2. Bandwidth mode for VSB(6MHz) */ |
| ret = lgdt3306a_read_reg(state, 0x0009, &val); |
| val &= 0xe3; |
| val |= 0x0c; /* STDOPDETTMODE[2:0]=3 */ |
| ret = lgdt3306a_write_reg(state, 0x0009, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 3. QAM mode detection mode(None) */ |
| ret = lgdt3306a_read_reg(state, 0x0009, &val); |
| val &= 0xfc; /* STDOPDETCMODE[1:0]=0 */ |
| ret = lgdt3306a_write_reg(state, 0x0009, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 4. ADC sampling frequency rate(2x sampling) */ |
| ret = lgdt3306a_read_reg(state, 0x000d, &val); |
| val &= 0xbf; /* SAMPLING4XFEN=0 */ |
| ret = lgdt3306a_write_reg(state, 0x000d, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| #if 0 |
| /* FGR - disable any AICC filtering, testing only */ |
| |
| ret = lgdt3306a_write_reg(state, 0x0024, 0x00); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* AICCFIXFREQ0 NT N-1(Video rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x002e, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x002f, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x0030, 0x00); |
| |
| /* AICCFIXFREQ1 NT N-1(Audio rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x002b, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x002c, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x002d, 0x00); |
| |
| /* AICCFIXFREQ2 NT Co-Channel(Video rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x0028, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x0029, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x002a, 0x00); |
| |
| /* AICCFIXFREQ3 NT Co-Channel(Audio rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x0025, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x0026, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x0027, 0x00); |
| |
| #else |
| /* FGR - this works well for HVR-1955,1975 */ |
| |
| /* 5. AICCOPMODE NT N-1 Adj. */ |
| ret = lgdt3306a_write_reg(state, 0x0024, 0x5A); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* AICCFIXFREQ0 NT N-1(Video rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x002e, 0x5A); |
| ret = lgdt3306a_write_reg(state, 0x002f, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x0030, 0x00); |
| |
| /* AICCFIXFREQ1 NT N-1(Audio rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x002b, 0x36); |
| ret = lgdt3306a_write_reg(state, 0x002c, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x002d, 0x00); |
| |
| /* AICCFIXFREQ2 NT Co-Channel(Video rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x0028, 0x2A); |
| ret = lgdt3306a_write_reg(state, 0x0029, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x002a, 0x00); |
| |
| /* AICCFIXFREQ3 NT Co-Channel(Audio rejection) */ |
| ret = lgdt3306a_write_reg(state, 0x0025, 0x06); |
| ret = lgdt3306a_write_reg(state, 0x0026, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x0027, 0x00); |
| #endif |
| |
| ret = lgdt3306a_read_reg(state, 0x001e, &val); |
| val &= 0x0f; |
| val |= 0xa0; |
| ret = lgdt3306a_write_reg(state, 0x001e, val); |
| |
| ret = lgdt3306a_write_reg(state, 0x0022, 0x08); |
| |
| ret = lgdt3306a_write_reg(state, 0x0023, 0xFF); |
| |
| ret = lgdt3306a_read_reg(state, 0x211f, &val); |
| val &= 0xef; |
| ret = lgdt3306a_write_reg(state, 0x211f, val); |
| |
| ret = lgdt3306a_write_reg(state, 0x2173, 0x01); |
| |
| ret = lgdt3306a_read_reg(state, 0x1061, &val); |
| val &= 0xf8; |
| val |= 0x04; |
| ret = lgdt3306a_write_reg(state, 0x1061, val); |
| |
| ret = lgdt3306a_read_reg(state, 0x103d, &val); |
| val &= 0xcf; |
| ret = lgdt3306a_write_reg(state, 0x103d, val); |
| |
| ret = lgdt3306a_write_reg(state, 0x2122, 0x40); |
| |
| ret = lgdt3306a_read_reg(state, 0x2141, &val); |
| val &= 0x3f; |
| ret = lgdt3306a_write_reg(state, 0x2141, val); |
| |
| ret = lgdt3306a_read_reg(state, 0x2135, &val); |
| val &= 0x0f; |
| val |= 0x70; |
| ret = lgdt3306a_write_reg(state, 0x2135, val); |
| |
| ret = lgdt3306a_read_reg(state, 0x0003, &val); |
| val &= 0xf7; |
| ret = lgdt3306a_write_reg(state, 0x0003, val); |
| |
| ret = lgdt3306a_read_reg(state, 0x001c, &val); |
| val &= 0x7f; |
| ret = lgdt3306a_write_reg(state, 0x001c, val); |
| |
| /* 6. EQ step size */ |
| ret = lgdt3306a_read_reg(state, 0x2179, &val); |
| val &= 0xf8; |
| ret = lgdt3306a_write_reg(state, 0x2179, val); |
| |
| ret = lgdt3306a_read_reg(state, 0x217a, &val); |
| val &= 0xf8; |
| ret = lgdt3306a_write_reg(state, 0x217a, val); |
| |
| /* 7. Reset */ |
| ret = lgdt3306a_soft_reset(state); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| dbg_info("complete\n"); |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_set_qam(struct lgdt3306a_state *state, int modulation) |
| { |
| u8 val; |
| int ret; |
| |
| dbg_info("modulation=%d\n", modulation); |
| |
| /* 1. Selection of standard mode(0x08=QAM, 0x80=VSB) */ |
| ret = lgdt3306a_write_reg(state, 0x0008, 0x08); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 1a. Spectrum inversion detection to Auto */ |
| ret = lgdt3306a_read_reg(state, 0x0002, &val); |
| val &= 0xfb; /* SPECINV Off */ |
| val |= 0x08; /* SPECINVAUTO On */ |
| ret = lgdt3306a_write_reg(state, 0x0002, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 2. Bandwidth mode for QAM */ |
| ret = lgdt3306a_read_reg(state, 0x0009, &val); |
| val &= 0xe3; /* STDOPDETTMODE[2:0]=0 VSB Off */ |
| ret = lgdt3306a_write_reg(state, 0x0009, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 3. : 64QAM/256QAM detection(manual, auto) */ |
| ret = lgdt3306a_read_reg(state, 0x0009, &val); |
| val &= 0xfc; |
| /* Check for forced Manual modulation modes; otherwise always "auto" */ |
| if(forced_manual && (modulation != QAM_AUTO)){ |
| val |= 0x01; /* STDOPDETCMODE[1:0]= 1=Manual */ |
| } else { |
| val |= 0x02; /* STDOPDETCMODE[1:0]= 2=Auto */ |
| } |
| ret = lgdt3306a_write_reg(state, 0x0009, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 3a. : 64QAM/256QAM selection for manual */ |
| ret = lgdt3306a_read_reg(state, 0x101a, &val); |
| val &= 0xf8; |
| if (modulation == QAM_64) |
| val |= 0x02; /* QMDQMODE[2:0]=2=QAM64 */ |
| else |
| val |= 0x04; /* QMDQMODE[2:0]=4=QAM256 */ |
| |
| ret = lgdt3306a_write_reg(state, 0x101a, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 4. ADC sampling frequency rate(4x sampling) */ |
| ret = lgdt3306a_read_reg(state, 0x000d, &val); |
| val &= 0xbf; |
| val |= 0x40; /* SAMPLING4XFEN=1 */ |
| ret = lgdt3306a_write_reg(state, 0x000d, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 5. No AICC operation in QAM mode */ |
| ret = lgdt3306a_read_reg(state, 0x0024, &val); |
| val &= 0x00; |
| ret = lgdt3306a_write_reg(state, 0x0024, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 5.1 V0.36 SRDCHKALWAYS : For better QAM detection */ |
| ret = lgdt3306a_read_reg(state, 0x000a, &val); |
| val &= 0xfd; |
| val |= 0x02; |
| ret = lgdt3306a_write_reg(state, 0x000a, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 5.2 V0.36 Control of "no signal" detector function */ |
| ret = lgdt3306a_read_reg(state, 0x2849, &val); |
| val &= 0xdf; |
| ret = lgdt3306a_write_reg(state, 0x2849, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 5.3 Fix for Blonder Tongue HDE-2H-QAM and AQM modulators */ |
| ret = lgdt3306a_read_reg(state, 0x302b, &val); |
| val &= 0x7f; /* SELFSYNCFINDEN_CQS=0; disable auto reset */ |
| ret = lgdt3306a_write_reg(state, 0x302b, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 6. Reset */ |
| ret = lgdt3306a_soft_reset(state); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| dbg_info("complete\n"); |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_set_modulation(struct lgdt3306a_state *state, |
| struct dtv_frontend_properties *p) |
| { |
| int ret; |
| |
| dbg_info("\n"); |
| |
| switch (p->modulation) { |
| case VSB_8: |
| ret = lgdt3306a_set_vsb(state); |
| break; |
| case QAM_64: |
| case QAM_256: |
| case QAM_AUTO: |
| ret = lgdt3306a_set_qam(state, p->modulation); |
| break; |
| default: |
| return -EINVAL; |
| } |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| state->current_modulation = p->modulation; |
| |
| fail: |
| return ret; |
| } |
| |
| /* ------------------------------------------------------------------------ */ |
| |
| static int lgdt3306a_agc_setup(struct lgdt3306a_state *state, |
| struct dtv_frontend_properties *p) |
| { |
| /* TODO: anything we want to do here??? */ |
| dbg_info("\n"); |
| |
| switch (p->modulation) { |
| case VSB_8: |
| break; |
| case QAM_64: |
| case QAM_256: |
| case QAM_AUTO: |
| break; |
| default: |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| /* ------------------------------------------------------------------------ */ |
| |
| static int lgdt3306a_set_inversion(struct lgdt3306a_state *state, |
| int inversion) |
| { |
| int ret; |
| |
| dbg_info("(%d)\n", inversion); |
| |
| ret = lgdt3306a_set_reg_bit(state, 0x0002, 2, inversion ? 1 : 0); |
| return ret; |
| } |
| |
| static int lgdt3306a_set_inversion_auto(struct lgdt3306a_state *state, |
| int enabled) |
| { |
| int ret; |
| |
| dbg_info("(%d)\n", enabled); |
| |
| /* 0=Manual 1=Auto(QAM only) - SPECINVAUTO=0x04 */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0002, 3, enabled); |
| return ret; |
| } |
| |
| static int lgdt3306a_set_if(struct lgdt3306a_state *state, |
| struct dtv_frontend_properties *p) |
| { |
| int ret; |
| u16 if_freq_khz; |
| u8 nco1, nco2; |
| |
| switch (p->modulation) { |
| case VSB_8: |
| if_freq_khz = state->cfg->vsb_if_khz; |
| break; |
| case QAM_64: |
| case QAM_256: |
| case QAM_AUTO: |
| if_freq_khz = state->cfg->qam_if_khz; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| switch (if_freq_khz) { |
| default: |
| pr_warn("IF=%d KHz is not supported, 3250 assumed\n", |
| if_freq_khz); |
| fallthrough; |
| case 3250: /* 3.25Mhz */ |
| nco1 = 0x34; |
| nco2 = 0x00; |
| break; |
| case 3500: /* 3.50Mhz */ |
| nco1 = 0x38; |
| nco2 = 0x00; |
| break; |
| case 4000: /* 4.00Mhz */ |
| nco1 = 0x40; |
| nco2 = 0x00; |
| break; |
| case 5000: /* 5.00Mhz */ |
| nco1 = 0x50; |
| nco2 = 0x00; |
| break; |
| case 5380: /* 5.38Mhz */ |
| nco1 = 0x56; |
| nco2 = 0x14; |
| break; |
| } |
| ret = lgdt3306a_write_reg(state, 0x0010, nco1); |
| if (ret) |
| return ret; |
| ret = lgdt3306a_write_reg(state, 0x0011, nco2); |
| if (ret) |
| return ret; |
| |
| dbg_info("if_freq=%d KHz->[%04x]\n", if_freq_khz, nco1<<8 | nco2); |
| |
| return 0; |
| } |
| |
| /* ------------------------------------------------------------------------ */ |
| |
| static int lgdt3306a_i2c_gate_ctrl(struct dvb_frontend *fe, int enable) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| if (state->cfg->deny_i2c_rptr) { |
| dbg_info("deny_i2c_rptr=%d\n", state->cfg->deny_i2c_rptr); |
| return 0; |
| } |
| dbg_info("(%d)\n", enable); |
| |
| /* NI2CRPTEN=0x80 */ |
| return lgdt3306a_set_reg_bit(state, 0x0002, 7, enable ? 0 : 1); |
| } |
| |
| static int lgdt3306a_sleep(struct lgdt3306a_state *state) |
| { |
| int ret; |
| |
| dbg_info("\n"); |
| state->current_frequency = -1; /* force re-tune, when we wake */ |
| |
| ret = lgdt3306a_mpeg_tristate(state, 1); /* disable data bus */ |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_power(state, 0); /* power down */ |
| lg_chkerr(ret); |
| |
| fail: |
| return 0; |
| } |
| |
| static int lgdt3306a_fe_sleep(struct dvb_frontend *fe) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| return lgdt3306a_sleep(state); |
| } |
| |
| static int lgdt3306a_init(struct dvb_frontend *fe) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| u8 val; |
| int ret; |
| |
| dbg_info("\n"); |
| |
| /* 1. Normal operation mode */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0001, 0, 1); /* SIMFASTENB=0x01 */ |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 2. Spectrum inversion auto detection (Not valid for VSB) */ |
| ret = lgdt3306a_set_inversion_auto(state, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 3. Spectrum inversion(According to the tuner configuration) */ |
| ret = lgdt3306a_set_inversion(state, 1); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 4. Peak-to-peak voltage of ADC input signal */ |
| |
| /* ADCSEL1V=0x80=1Vpp; 0x00=2Vpp */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0004, 7, 1); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 5. ADC output data capture clock phase */ |
| |
| /* 0=same phase as ADC clock */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0004, 2, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 5a. ADC sampling clock source */ |
| |
| /* ADCCLKPLLSEL=0x08; 0=use ext clock, not PLL */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0004, 3, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 6. Automatic PLL set */ |
| |
| /* PLLSETAUTO=0x40; 0=off */ |
| ret = lgdt3306a_set_reg_bit(state, 0x0005, 6, 0); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| if (state->cfg->xtalMHz == 24) { /* 24MHz */ |
| /* 7. Frequency for PLL output(0x2564 for 192MHz for 24MHz) */ |
| ret = lgdt3306a_read_reg(state, 0x0005, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| val &= 0xc0; |
| val |= 0x25; |
| ret = lgdt3306a_write_reg(state, 0x0005, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| ret = lgdt3306a_write_reg(state, 0x0006, 0x64); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 8. ADC sampling frequency(0x180000 for 24MHz sampling) */ |
| ret = lgdt3306a_read_reg(state, 0x000d, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| val &= 0xc0; |
| val |= 0x18; |
| ret = lgdt3306a_write_reg(state, 0x000d, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| } else if (state->cfg->xtalMHz == 25) { /* 25MHz */ |
| /* 7. Frequency for PLL output */ |
| ret = lgdt3306a_read_reg(state, 0x0005, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| val &= 0xc0; |
| val |= 0x25; |
| ret = lgdt3306a_write_reg(state, 0x0005, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| ret = lgdt3306a_write_reg(state, 0x0006, 0x64); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* 8. ADC sampling frequency(0x190000 for 25MHz sampling) */ |
| ret = lgdt3306a_read_reg(state, 0x000d, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| val &= 0xc0; |
| val |= 0x19; |
| ret = lgdt3306a_write_reg(state, 0x000d, val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| } else { |
| pr_err("Bad xtalMHz=%d\n", state->cfg->xtalMHz); |
| } |
| #if 0 |
| ret = lgdt3306a_write_reg(state, 0x000e, 0x00); |
| ret = lgdt3306a_write_reg(state, 0x000f, 0x00); |
| #endif |
| |
| /* 9. Center frequency of input signal of ADC */ |
| ret = lgdt3306a_write_reg(state, 0x0010, 0x34); /* 3.25MHz */ |
| ret = lgdt3306a_write_reg(state, 0x0011, 0x00); |
| |
| /* 10. Fixed gain error value */ |
| ret = lgdt3306a_write_reg(state, 0x0014, 0); /* gain error=0 */ |
| |
| /* 10a. VSB TR BW gear shift initial step */ |
| ret = lgdt3306a_read_reg(state, 0x103c, &val); |
| val &= 0x0f; |
| val |= 0x20; /* SAMGSAUTOSTL_V[3:0] = 2 */ |
| ret = lgdt3306a_write_reg(state, 0x103c, val); |
| |
| /* 10b. Timing offset calibration in low temperature for VSB */ |
| ret = lgdt3306a_read_reg(state, 0x103d, &val); |
| val &= 0xfc; |
| val |= 0x03; |
| ret = lgdt3306a_write_reg(state, 0x103d, val); |
| |
| /* 10c. Timing offset calibration in low temperature for QAM */ |
| ret = lgdt3306a_read_reg(state, 0x1036, &val); |
| val &= 0xf0; |
| val |= 0x0c; |
| ret = lgdt3306a_write_reg(state, 0x1036, val); |
| |
| /* 11. Using the imaginary part of CIR in CIR loading */ |
| ret = lgdt3306a_read_reg(state, 0x211f, &val); |
| val &= 0xef; /* do not use imaginary of CIR */ |
| ret = lgdt3306a_write_reg(state, 0x211f, val); |
| |
| /* 12. Control of no signal detector function */ |
| ret = lgdt3306a_read_reg(state, 0x2849, &val); |
| val &= 0xef; /* NOUSENOSIGDET=0, enable no signal detector */ |
| ret = lgdt3306a_write_reg(state, 0x2849, val); |
| |
| /* FGR - put demod in some known mode */ |
| ret = lgdt3306a_set_vsb(state); |
| |
| /* 13. TP stream format */ |
| ret = lgdt3306a_mpeg_mode(state, state->cfg->mpeg_mode); |
| |
| /* 14. disable output buses */ |
| ret = lgdt3306a_mpeg_tristate(state, 1); |
| |
| /* 15. Sleep (in reset) */ |
| ret = lgdt3306a_sleep(state); |
| lg_chkerr(ret); |
| |
| c->cnr.len = 1; |
| c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_set_parameters(struct dvb_frontend *fe) |
| { |
| struct dtv_frontend_properties *p = &fe->dtv_property_cache; |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| int ret; |
| |
| dbg_info("(%d, %d)\n", p->frequency, p->modulation); |
| |
| if (state->current_frequency == p->frequency && |
| state->current_modulation == p->modulation) { |
| dbg_info(" (already set, skipping ...)\n"); |
| return 0; |
| } |
| state->current_frequency = -1; |
| state->current_modulation = -1; |
| |
| ret = lgdt3306a_power(state, 1); /* power up */ |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| if (fe->ops.tuner_ops.set_params) { |
| ret = fe->ops.tuner_ops.set_params(fe); |
| if (fe->ops.i2c_gate_ctrl) |
| fe->ops.i2c_gate_ctrl(fe, 0); |
| #if 0 |
| if (lg_chkerr(ret)) |
| goto fail; |
| state->current_frequency = p->frequency; |
| #endif |
| } |
| |
| ret = lgdt3306a_set_modulation(state, p); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_agc_setup(state, p); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_set_if(state, p); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| /* spectral_inversion defaults already set for VSB and QAM */ |
| |
| ret = lgdt3306a_mpeg_mode(state, state->cfg->mpeg_mode); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_mpeg_mode_polarity(state, |
| state->cfg->tpclk_edge, |
| state->cfg->tpvalid_polarity); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_mpeg_tristate(state, 0); /* enable data bus */ |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| ret = lgdt3306a_soft_reset(state); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| #ifdef DBG_DUMP |
| lgdt3306a_DumpAllRegs(state); |
| #endif |
| state->current_frequency = p->frequency; |
| fail: |
| return ret; |
| } |
| |
| static int lgdt3306a_get_frontend(struct dvb_frontend *fe, |
| struct dtv_frontend_properties *p) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| dbg_info("(%u, %d)\n", |
| state->current_frequency, state->current_modulation); |
| |
| p->modulation = state->current_modulation; |
| p->frequency = state->current_frequency; |
| return 0; |
| } |
| |
| static enum dvbfe_algo lgdt3306a_get_frontend_algo(struct dvb_frontend *fe) |
| { |
| #if 1 |
| return DVBFE_ALGO_CUSTOM; |
| #else |
| return DVBFE_ALGO_HW; |
| #endif |
| } |
| |
| /* ------------------------------------------------------------------------ */ |
| static int lgdt3306a_monitor_vsb(struct lgdt3306a_state *state) |
| { |
| u8 val; |
| int ret; |
| u8 snrRef, maxPowerMan, nCombDet; |
| u16 fbDlyCir; |
| |
| ret = lgdt3306a_read_reg(state, 0x21a1, &val); |
| if (ret) |
| return ret; |
| snrRef = val & 0x3f; |
| |
| ret = lgdt3306a_read_reg(state, 0x2185, &maxPowerMan); |
| if (ret) |
| return ret; |
| |
| ret = lgdt3306a_read_reg(state, 0x2191, &val); |
| if (ret) |
| return ret; |
| nCombDet = (val & 0x80) >> 7; |
| |
| ret = lgdt3306a_read_reg(state, 0x2180, &val); |
| if (ret) |
| return ret; |
| fbDlyCir = (val & 0x03) << 8; |
| |
| ret = lgdt3306a_read_reg(state, 0x2181, &val); |
| if (ret) |
| return ret; |
| fbDlyCir |= val; |
| |
| dbg_info("snrRef=%d maxPowerMan=0x%x nCombDet=%d fbDlyCir=0x%x\n", |
| snrRef, maxPowerMan, nCombDet, fbDlyCir); |
| |
| /* Carrier offset sub loop bandwidth */ |
| ret = lgdt3306a_read_reg(state, 0x1061, &val); |
| if (ret) |
| return ret; |
| val &= 0xf8; |
| if ((snrRef > 18) && (maxPowerMan > 0x68) |
| && (nCombDet == 0x01) |
| && ((fbDlyCir == 0x03FF) || (fbDlyCir < 0x6C))) { |
| /* SNR is over 18dB and no ghosting */ |
| val |= 0x00; /* final bandwidth = 0 */ |
| } else { |
| val |= 0x04; /* final bandwidth = 4 */ |
| } |
| ret = lgdt3306a_write_reg(state, 0x1061, val); |
| if (ret) |
| return ret; |
| |
| /* Adjust Notch Filter */ |
| ret = lgdt3306a_read_reg(state, 0x0024, &val); |
| if (ret) |
| return ret; |
| val &= 0x0f; |
| if (nCombDet == 0) { /* Turn on the Notch Filter */ |
| val |= 0x50; |
| } |
| ret = lgdt3306a_write_reg(state, 0x0024, val); |
| if (ret) |
| return ret; |
| |
| /* VSB Timing Recovery output normalization */ |
| ret = lgdt3306a_read_reg(state, 0x103d, &val); |
| if (ret) |
| return ret; |
| val &= 0xcf; |
| val |= 0x20; |
| ret = lgdt3306a_write_reg(state, 0x103d, val); |
| |
| return ret; |
| } |
| |
| static enum lgdt3306a_modulation |
| lgdt3306a_check_oper_mode(struct lgdt3306a_state *state) |
| { |
| u8 val = 0; |
| int ret; |
| |
| ret = lgdt3306a_read_reg(state, 0x0081, &val); |
| if (ret) |
| goto err; |
| |
| if (val & 0x80) { |
| dbg_info("VSB\n"); |
| return LG3306_VSB; |
| } |
| if (val & 0x08) { |
| ret = lgdt3306a_read_reg(state, 0x00a6, &val); |
| if (ret) |
| goto err; |
| val = val >> 2; |
| if (val & 0x01) { |
| dbg_info("QAM256\n"); |
| return LG3306_QAM256; |
| } |
| dbg_info("QAM64\n"); |
| return LG3306_QAM64; |
| } |
| err: |
| pr_warn("UNKNOWN\n"); |
| return LG3306_UNKNOWN_MODE; |
| } |
| |
| static enum lgdt3306a_lock_status |
| lgdt3306a_check_lock_status(struct lgdt3306a_state *state, |
| enum lgdt3306a_lock_check whatLock) |
| { |
| u8 val = 0; |
| int ret; |
| enum lgdt3306a_modulation modeOper; |
| enum lgdt3306a_lock_status lockStatus; |
| |
| modeOper = LG3306_UNKNOWN_MODE; |
| |
| switch (whatLock) { |
| case LG3306_SYNC_LOCK: |
| { |
| ret = lgdt3306a_read_reg(state, 0x00a6, &val); |
| if (ret) |
| return ret; |
| |
| if ((val & 0x80) == 0x80) |
| lockStatus = LG3306_LOCK; |
| else |
| lockStatus = LG3306_UNLOCK; |
| |
| dbg_info("SYNC_LOCK=%x\n", lockStatus); |
| break; |
| } |
| case LG3306_AGC_LOCK: |
| { |
| ret = lgdt3306a_read_reg(state, 0x0080, &val); |
| if (ret) |
| return ret; |
| |
| if ((val & 0x40) == 0x40) |
| lockStatus = LG3306_LOCK; |
| else |
| lockStatus = LG3306_UNLOCK; |
| |
| dbg_info("AGC_LOCK=%x\n", lockStatus); |
| break; |
| } |
| case LG3306_TR_LOCK: |
| { |
| modeOper = lgdt3306a_check_oper_mode(state); |
| if ((modeOper == LG3306_QAM64) || (modeOper == LG3306_QAM256)) { |
| ret = lgdt3306a_read_reg(state, 0x1094, &val); |
| if (ret) |
| return ret; |
| |
| if ((val & 0x80) == 0x80) |
| lockStatus = LG3306_LOCK; |
| else |
| lockStatus = LG3306_UNLOCK; |
| } else |
| lockStatus = LG3306_UNKNOWN_LOCK; |
| |
| dbg_info("TR_LOCK=%x\n", lockStatus); |
| break; |
| } |
| case LG3306_FEC_LOCK: |
| { |
| modeOper = lgdt3306a_check_oper_mode(state); |
| if ((modeOper == LG3306_QAM64) || (modeOper == LG3306_QAM256)) { |
| ret = lgdt3306a_read_reg(state, 0x0080, &val); |
| if (ret) |
| return ret; |
| |
| if ((val & 0x10) == 0x10) |
| lockStatus = LG3306_LOCK; |
| else |
| lockStatus = LG3306_UNLOCK; |
| } else |
| lockStatus = LG3306_UNKNOWN_LOCK; |
| |
| dbg_info("FEC_LOCK=%x\n", lockStatus); |
| break; |
| } |
| |
| default: |
| lockStatus = LG3306_UNKNOWN_LOCK; |
| pr_warn("UNKNOWN whatLock=%d\n", whatLock); |
| break; |
| } |
| |
| return lockStatus; |
| } |
| |
| static enum lgdt3306a_neverlock_status |
| lgdt3306a_check_neverlock_status(struct lgdt3306a_state *state) |
| { |
| u8 val = 0; |
| int ret; |
| enum lgdt3306a_neverlock_status lockStatus; |
| |
| ret = lgdt3306a_read_reg(state, 0x0080, &val); |
| if (ret) |
| return ret; |
| lockStatus = (enum lgdt3306a_neverlock_status)(val & 0x03); |
| |
| dbg_info("NeverLock=%d", lockStatus); |
| |
| return lockStatus; |
| } |
| |
| static int lgdt3306a_pre_monitoring(struct lgdt3306a_state *state) |
| { |
| u8 val = 0; |
| int ret; |
| u8 currChDiffACQ, snrRef, mainStrong, aiccrejStatus; |
| |
| /* Channel variation */ |
| ret = lgdt3306a_read_reg(state, 0x21bc, &currChDiffACQ); |
| if (ret) |
| return ret; |
| |
| /* SNR of Frame sync */ |
| ret = lgdt3306a_read_reg(state, 0x21a1, &val); |
| if (ret) |
| return ret; |
| snrRef = val & 0x3f; |
| |
| /* Strong Main CIR */ |
| ret = lgdt3306a_read_reg(state, 0x2199, &val); |
| if (ret) |
| return ret; |
| mainStrong = (val & 0x40) >> 6; |
| |
| ret = lgdt3306a_read_reg(state, 0x0090, &val); |
| if (ret) |
| return ret; |
| aiccrejStatus = (val & 0xf0) >> 4; |
| |
| dbg_info("snrRef=%d mainStrong=%d aiccrejStatus=%d currChDiffACQ=0x%x\n", |
| snrRef, mainStrong, aiccrejStatus, currChDiffACQ); |
| |
| #if 0 |
| /* Dynamic ghost exists */ |
| if ((mainStrong == 0) && (currChDiffACQ > 0x70)) |
| #endif |
| if (mainStrong == 0) { |
| ret = lgdt3306a_read_reg(state, 0x2135, &val); |
| if (ret) |
| return ret; |
| val &= 0x0f; |
| val |= 0xa0; |
| ret = lgdt3306a_write_reg(state, 0x2135, val); |
| if (ret) |
| return ret; |
| |
| ret = lgdt3306a_read_reg(state, 0x2141, &val); |
| if (ret) |
| return ret; |
| val &= 0x3f; |
| val |= 0x80; |
| ret = lgdt3306a_write_reg(state, 0x2141, val); |
| if (ret) |
| return ret; |
| |
| ret = lgdt3306a_write_reg(state, 0x2122, 0x70); |
| if (ret) |
| return ret; |
| } else { /* Weak ghost or static channel */ |
| ret = lgdt3306a_read_reg(state, 0x2135, &val); |
| if (ret) |
| return ret; |
| val &= 0x0f; |
| val |= 0x70; |
| ret = lgdt3306a_write_reg(state, 0x2135, val); |
| if (ret) |
| return ret; |
| |
| ret = lgdt3306a_read_reg(state, 0x2141, &val); |
| if (ret) |
| return ret; |
| val &= 0x3f; |
| val |= 0x40; |
| ret = lgdt3306a_write_reg(state, 0x2141, val); |
| if (ret) |
| return ret; |
| |
| ret = lgdt3306a_write_reg(state, 0x2122, 0x40); |
| if (ret) |
| return ret; |
| } |
| return 0; |
| } |
| |
| static enum lgdt3306a_lock_status |
| lgdt3306a_sync_lock_poll(struct lgdt3306a_state *state) |
| { |
| enum lgdt3306a_lock_status syncLockStatus = LG3306_UNLOCK; |
| int i; |
| |
| for (i = 0; i < 2; i++) { |
| msleep(30); |
| |
| syncLockStatus = lgdt3306a_check_lock_status(state, |
| LG3306_SYNC_LOCK); |
| |
| if (syncLockStatus == LG3306_LOCK) { |
| dbg_info("locked(%d)\n", i); |
| return LG3306_LOCK; |
| } |
| } |
| dbg_info("not locked\n"); |
| return LG3306_UNLOCK; |
| } |
| |
| static enum lgdt3306a_lock_status |
| lgdt3306a_fec_lock_poll(struct lgdt3306a_state *state) |
| { |
| enum lgdt3306a_lock_status FECLockStatus = LG3306_UNLOCK; |
| int i; |
| |
| for (i = 0; i < 2; i++) { |
| msleep(30); |
| |
| FECLockStatus = lgdt3306a_check_lock_status(state, |
| LG3306_FEC_LOCK); |
| |
| if (FECLockStatus == LG3306_LOCK) { |
| dbg_info("locked(%d)\n", i); |
| return FECLockStatus; |
| } |
| } |
| dbg_info("not locked\n"); |
| return FECLockStatus; |
| } |
| |
| static enum lgdt3306a_neverlock_status |
| lgdt3306a_neverlock_poll(struct lgdt3306a_state *state) |
| { |
| enum lgdt3306a_neverlock_status NLLockStatus = LG3306_NL_FAIL; |
| int i; |
| |
| for (i = 0; i < 5; i++) { |
| msleep(30); |
| |
| NLLockStatus = lgdt3306a_check_neverlock_status(state); |
| |
| if (NLLockStatus == LG3306_NL_LOCK) { |
| dbg_info("NL_LOCK(%d)\n", i); |
| return NLLockStatus; |
| } |
| } |
| dbg_info("NLLockStatus=%d\n", NLLockStatus); |
| return NLLockStatus; |
| } |
| |
| static u8 lgdt3306a_get_packet_error(struct lgdt3306a_state *state) |
| { |
| u8 val; |
| int ret; |
| |
| ret = lgdt3306a_read_reg(state, 0x00fa, &val); |
| if (ret) |
| return ret; |
| |
| return val; |
| } |
| |
| static const u32 valx_x10[] = { |
| 10, 11, 13, 15, 17, 20, 25, 33, 41, 50, 59, 73, 87, 100 |
| }; |
| static const u32 log10x_x1000[] = { |
| 0, 41, 114, 176, 230, 301, 398, 518, 613, 699, 771, 863, 939, 1000 |
| }; |
| |
| static u32 log10_x1000(u32 x) |
| { |
| u32 diff_val, step_val, step_log10; |
| u32 log_val = 0; |
| u32 i; |
| |
| if (x <= 0) |
| return -1000000; /* signal error */ |
| |
| if (x == 10) |
| return 0; /* log(1)=0 */ |
| |
| if (x < 10) { |
| while (x < 10) { |
| x = x * 10; |
| log_val--; |
| } |
| } else { /* x > 10 */ |
| while (x >= 100) { |
| x = x / 10; |
| log_val++; |
| } |
| } |
| log_val *= 1000; |
| |
| if (x == 10) /* was our input an exact multiple of 10 */ |
| return log_val; /* don't need to interpolate */ |
| |
| /* find our place on the log curve */ |
| for (i = 1; i < ARRAY_SIZE(valx_x10); i++) { |
| if (valx_x10[i] >= x) |
| break; |
| } |
| if (i == ARRAY_SIZE(valx_x10)) |
| return log_val + log10x_x1000[i - 1]; |
| |
| diff_val = x - valx_x10[i-1]; |
| step_val = valx_x10[i] - valx_x10[i - 1]; |
| step_log10 = log10x_x1000[i] - log10x_x1000[i - 1]; |
| |
| /* do a linear interpolation to get in-between values */ |
| return log_val + log10x_x1000[i - 1] + |
| ((diff_val*step_log10) / step_val); |
| } |
| |
| static u32 lgdt3306a_calculate_snr_x100(struct lgdt3306a_state *state) |
| { |
| u32 mse; /* Mean-Square Error */ |
| u32 pwr; /* Constelation power */ |
| u32 snr_x100; |
| |
| mse = (read_reg(state, 0x00ec) << 8) | |
| (read_reg(state, 0x00ed)); |
| pwr = (read_reg(state, 0x00e8) << 8) | |
| (read_reg(state, 0x00e9)); |
| |
| if (mse == 0) /* no signal */ |
| return 0; |
| |
| snr_x100 = log10_x1000((pwr * 10000) / mse) - 3000; |
| dbg_info("mse=%u, pwr=%u, snr_x100=%d\n", mse, pwr, snr_x100); |
| |
| return snr_x100; |
| } |
| |
| static enum lgdt3306a_lock_status |
| lgdt3306a_vsb_lock_poll(struct lgdt3306a_state *state) |
| { |
| int ret; |
| u8 cnt = 0; |
| u8 packet_error; |
| u32 snr; |
| |
| for (cnt = 0; cnt < 10; cnt++) { |
| if (lgdt3306a_sync_lock_poll(state) == LG3306_UNLOCK) { |
| dbg_info("no sync lock!\n"); |
| return LG3306_UNLOCK; |
| } |
| |
| msleep(20); |
| ret = lgdt3306a_pre_monitoring(state); |
| if (ret) |
| break; |
| |
| packet_error = lgdt3306a_get_packet_error(state); |
| snr = lgdt3306a_calculate_snr_x100(state); |
| dbg_info("cnt=%d errors=%d snr=%d\n", cnt, packet_error, snr); |
| |
| if ((snr >= 1500) && (packet_error < 0xff)) |
| return LG3306_LOCK; |
| } |
| |
| dbg_info("not locked!\n"); |
| return LG3306_UNLOCK; |
| } |
| |
| static enum lgdt3306a_lock_status |
| lgdt3306a_qam_lock_poll(struct lgdt3306a_state *state) |
| { |
| u8 cnt; |
| u8 packet_error; |
| u32 snr; |
| |
| for (cnt = 0; cnt < 10; cnt++) { |
| if (lgdt3306a_fec_lock_poll(state) == LG3306_UNLOCK) { |
| dbg_info("no fec lock!\n"); |
| return LG3306_UNLOCK; |
| } |
| |
| msleep(20); |
| |
| packet_error = lgdt3306a_get_packet_error(state); |
| snr = lgdt3306a_calculate_snr_x100(state); |
| dbg_info("cnt=%d errors=%d snr=%d\n", cnt, packet_error, snr); |
| |
| if ((snr >= 1500) && (packet_error < 0xff)) |
| return LG3306_LOCK; |
| } |
| |
| dbg_info("not locked!\n"); |
| return LG3306_UNLOCK; |
| } |
| |
| static int lgdt3306a_read_status(struct dvb_frontend *fe, |
| enum fe_status *status) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| u16 strength = 0; |
| int ret = 0; |
| |
| if (fe->ops.tuner_ops.get_rf_strength) { |
| ret = fe->ops.tuner_ops.get_rf_strength(fe, &strength); |
| if (ret == 0) |
| dbg_info("strength=%d\n", strength); |
| else |
| dbg_info("fe->ops.tuner_ops.get_rf_strength() failed\n"); |
| } |
| |
| *status = 0; |
| if (lgdt3306a_neverlock_poll(state) == LG3306_NL_LOCK) { |
| *status |= FE_HAS_SIGNAL; |
| *status |= FE_HAS_CARRIER; |
| |
| switch (state->current_modulation) { |
| case QAM_256: |
| case QAM_64: |
| case QAM_AUTO: |
| if (lgdt3306a_qam_lock_poll(state) == LG3306_LOCK) { |
| *status |= FE_HAS_VITERBI; |
| *status |= FE_HAS_SYNC; |
| |
| *status |= FE_HAS_LOCK; |
| } |
| break; |
| case VSB_8: |
| if (lgdt3306a_vsb_lock_poll(state) == LG3306_LOCK) { |
| *status |= FE_HAS_VITERBI; |
| *status |= FE_HAS_SYNC; |
| |
| *status |= FE_HAS_LOCK; |
| |
| ret = lgdt3306a_monitor_vsb(state); |
| } |
| break; |
| default: |
| ret = -EINVAL; |
| } |
| |
| if (*status & FE_HAS_SYNC) { |
| c->cnr.len = 1; |
| c->cnr.stat[0].scale = FE_SCALE_DECIBEL; |
| c->cnr.stat[0].svalue = lgdt3306a_calculate_snr_x100(state) * 10; |
| } else { |
| c->cnr.len = 1; |
| c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| } |
| } |
| return ret; |
| } |
| |
| |
| static int lgdt3306a_read_snr(struct dvb_frontend *fe, u16 *snr) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| state->snr = lgdt3306a_calculate_snr_x100(state); |
| /* report SNR in dB * 10 */ |
| *snr = state->snr/10; |
| |
| return 0; |
| } |
| |
| static int lgdt3306a_read_signal_strength(struct dvb_frontend *fe, |
| u16 *strength) |
| { |
| /* |
| * Calculate some sort of "strength" from SNR |
| */ |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| u8 val; |
| u16 snr; /* snr_x10 */ |
| int ret; |
| u32 ref_snr; /* snr*100 */ |
| u32 str; |
| |
| *strength = 0; |
| |
| switch (state->current_modulation) { |
| case VSB_8: |
| ref_snr = 1600; /* 16dB */ |
| break; |
| case QAM_64: |
| case QAM_256: |
| case QAM_AUTO: |
| /* need to know actual modulation to set proper SNR baseline */ |
| ret = lgdt3306a_read_reg(state, 0x00a6, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| if(val & 0x04) |
| ref_snr = 2800; /* QAM-256 28dB */ |
| else |
| ref_snr = 2200; /* QAM-64 22dB */ |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| ret = fe->ops.read_snr(fe, &snr); |
| if (lg_chkerr(ret)) |
| goto fail; |
| |
| if (state->snr <= (ref_snr - 100)) |
| str = 0; |
| else if (state->snr <= ref_snr) |
| str = (0xffff * 65) / 100; /* 65% */ |
| else { |
| str = state->snr - ref_snr; |
| str /= 50; |
| str += 78; /* 78%-100% */ |
| if (str > 100) |
| str = 100; |
| str = (0xffff * str) / 100; |
| } |
| *strength = (u16)str; |
| dbg_info("strength=%u\n", *strength); |
| |
| fail: |
| return ret; |
| } |
| |
| /* ------------------------------------------------------------------------ */ |
| |
| static int lgdt3306a_read_ber(struct dvb_frontend *fe, u32 *ber) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| u32 tmp; |
| |
| *ber = 0; |
| #if 1 |
| /* FGR - FIXME - I don't know what value is expected by dvb_core |
| * what is the scale of the value?? */ |
| tmp = read_reg(state, 0x00fc); /* NBERVALUE[24-31] */ |
| tmp = (tmp << 8) | read_reg(state, 0x00fd); /* NBERVALUE[16-23] */ |
| tmp = (tmp << 8) | read_reg(state, 0x00fe); /* NBERVALUE[8-15] */ |
| tmp = (tmp << 8) | read_reg(state, 0x00ff); /* NBERVALUE[0-7] */ |
| *ber = tmp; |
| dbg_info("ber=%u\n", tmp); |
| #endif |
| return 0; |
| } |
| |
| static int lgdt3306a_read_ucblocks(struct dvb_frontend *fe, u32 *ucblocks) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| *ucblocks = 0; |
| #if 1 |
| /* FGR - FIXME - I don't know what value is expected by dvb_core |
| * what happens when value wraps? */ |
| *ucblocks = read_reg(state, 0x00f4); /* TPIFTPERRCNT[0-7] */ |
| dbg_info("ucblocks=%u\n", *ucblocks); |
| #endif |
| |
| return 0; |
| } |
| |
| static int lgdt3306a_tune(struct dvb_frontend *fe, bool re_tune, |
| unsigned int mode_flags, unsigned int *delay, |
| enum fe_status *status) |
| { |
| int ret = 0; |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| dbg_info("re_tune=%u\n", re_tune); |
| |
| if (re_tune) { |
| state->current_frequency = -1; /* force re-tune */ |
| ret = lgdt3306a_set_parameters(fe); |
| if (ret != 0) |
| return ret; |
| } |
| *delay = 125; |
| ret = lgdt3306a_read_status(fe, status); |
| |
| return ret; |
| } |
| |
| static int lgdt3306a_get_tune_settings(struct dvb_frontend *fe, |
| struct dvb_frontend_tune_settings |
| *fe_tune_settings) |
| { |
| fe_tune_settings->min_delay_ms = 100; |
| dbg_info("\n"); |
| return 0; |
| } |
| |
| static enum dvbfe_search lgdt3306a_search(struct dvb_frontend *fe) |
| { |
| enum fe_status status = 0; |
| int ret; |
| |
| /* set frontend */ |
| ret = lgdt3306a_set_parameters(fe); |
| if (ret) |
| goto error; |
| |
| ret = lgdt3306a_read_status(fe, &status); |
| if (ret) |
| goto error; |
| |
| /* check if we have a valid signal */ |
| if (status & FE_HAS_LOCK) |
| return DVBFE_ALGO_SEARCH_SUCCESS; |
| else |
| return DVBFE_ALGO_SEARCH_AGAIN; |
| |
| error: |
| dbg_info("failed (%d)\n", ret); |
| return DVBFE_ALGO_SEARCH_ERROR; |
| } |
| |
| static void lgdt3306a_release(struct dvb_frontend *fe) |
| { |
| struct lgdt3306a_state *state = fe->demodulator_priv; |
| |
| dbg_info("\n"); |
| kfree(state); |
| } |
| |
| static const struct dvb_frontend_ops lgdt3306a_ops; |
| |
| struct dvb_frontend *lgdt3306a_attach(const struct lgdt3306a_config *config, |
| struct i2c_adapter *i2c_adap) |
| { |
| struct lgdt3306a_state *state = NULL; |
| int ret; |
| u8 val; |
| |
| dbg_info("(%d-%04x)\n", |
| i2c_adap ? i2c_adapter_id(i2c_adap) : 0, |
| config ? config->i2c_addr : 0); |
| |
| state = kzalloc(sizeof(struct lgdt3306a_state), GFP_KERNEL); |
| if (state == NULL) |
| goto fail; |
| |
| state->cfg = config; |
| state->i2c_adap = i2c_adap; |
| |
| memcpy(&state->frontend.ops, &lgdt3306a_ops, |
| sizeof(struct dvb_frontend_ops)); |
| state->frontend.demodulator_priv = state; |
| |
| /* verify that we're talking to a lg3306a */ |
| /* FGR - NOTE - there is no obvious ChipId to check; we check |
| * some "known" bits after reset, but it's still just a guess */ |
| ret = lgdt3306a_read_reg(state, 0x0000, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| if ((val & 0x74) != 0x74) { |
| pr_warn("expected 0x74, got 0x%x\n", (val & 0x74)); |
| #if 0 |
| /* FIXME - re-enable when we know this is right */ |
| goto fail; |
| #endif |
| } |
| ret = lgdt3306a_read_reg(state, 0x0001, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| if ((val & 0xf6) != 0xc6) { |
| pr_warn("expected 0xc6, got 0x%x\n", (val & 0xf6)); |
| #if 0 |
| /* FIXME - re-enable when we know this is right */ |
| goto fail; |
| #endif |
| } |
| ret = lgdt3306a_read_reg(state, 0x0002, &val); |
| if (lg_chkerr(ret)) |
| goto fail; |
| if ((val & 0x73) != 0x03) { |
| pr_warn("expected 0x03, got 0x%x\n", (val & 0x73)); |
| #if 0 |
| /* FIXME - re-enable when we know this is right */ |
| goto fail; |
| #endif |
| } |
| |
| state->current_frequency = -1; |
| state->current_modulation = -1; |
| |
| lgdt3306a_sleep(state); |
| |
| return &state->frontend; |
| |
| fail: |
| pr_warn("unable to detect LGDT3306A hardware\n"); |
| kfree(state); |
| return NULL; |
| } |
| EXPORT_SYMBOL_GPL(lgdt3306a_attach); |
| |
| #ifdef DBG_DUMP |
| |
| static const short regtab[] = { |
| 0x0000, /* SOFTRSTB 1'b1 1'b1 1'b1 ADCPDB 1'b1 PLLPDB GBBPDB 11111111 */ |
| 0x0001, /* 1'b1 1'b1 1'b0 1'b0 AUTORPTRS */ |
| 0x0002, /* NI2CRPTEN 1'b0 1'b0 1'b0 SPECINVAUT */ |
| 0x0003, /* AGCRFOUT */ |
| 0x0004, /* ADCSEL1V ADCCNT ADCCNF ADCCNS ADCCLKPLL */ |
| 0x0005, /* PLLINDIVSE */ |
| 0x0006, /* PLLCTRL[7:0] 11100001 */ |
| 0x0007, /* SYSINITWAITTIME[7:0] (msec) 00001000 */ |
| 0x0008, /* STDOPMODE[7:0] 10000000 */ |
| 0x0009, /* 1'b0 1'b0 1'b0 STDOPDETTMODE[2:0] STDOPDETCMODE[1:0] 00011110 */ |
| 0x000a, /* DAFTEN 1'b1 x x SCSYSLOCK */ |
| 0x000b, /* SCSYSLOCKCHKTIME[7:0] (10msec) 01100100 */ |
| 0x000d, /* x SAMPLING4 */ |
| 0x000e, /* SAMFREQ[15:8] 00000000 */ |
| 0x000f, /* SAMFREQ[7:0] 00000000 */ |
| 0x0010, /* IFFREQ[15:8] 01100000 */ |
| 0x0011, /* IFFREQ[7:0] 00000000 */ |
| 0x0012, /* AGCEN AGCREFMO */ |
| 0x0013, /* AGCRFFIXB AGCIFFIXB AGCLOCKDETRNGSEL[1:0] 1'b1 1'b0 1'b0 1'b0 11101000 */ |
| 0x0014, /* AGCFIXVALUE[7:0] 01111111 */ |
| 0x0015, /* AGCREF[15:8] 00001010 */ |
| 0x0016, /* AGCREF[7:0] 11100100 */ |
| 0x0017, /* AGCDELAY[7:0] 00100000 */ |
| 0x0018, /* AGCRFBW[3:0] AGCIFBW[3:0] 10001000 */ |
| 0x0019, /* AGCUDOUTMODE[1:0] AGCUDCTRLLEN[1:0] AGCUDCTRL */ |
| 0x001c, /* 1'b1 PFEN MFEN AICCVSYNC */ |
| 0x001d, /* 1'b0 1'b1 1'b0 1'b1 AICCVSYNC */ |
| 0x001e, /* AICCALPHA[3:0] 1'b1 1'b0 1'b1 1'b0 01111010 */ |
| 0x001f, /* AICCDETTH[19:16] AICCOFFTH[19:16] 00000000 */ |
| 0x0020, /* AICCDETTH[15:8] 01111100 */ |
| 0x0021, /* AICCDETTH[7:0] 00000000 */ |
| 0x0022, /* AICCOFFTH[15:8] 00000101 */ |
| 0x0023, /* AICCOFFTH[7:0] 11100000 */ |
| 0x0024, /* AICCOPMODE3[1:0] AICCOPMODE2[1:0] AICCOPMODE1[1:0] AICCOPMODE0[1:0] 00000000 */ |
| 0x0025, /* AICCFIXFREQ3[23:16] 00000000 */ |
| 0x0026, /* AICCFIXFREQ3[15:8] 00000000 */ |
| 0x0027, /* AICCFIXFREQ3[7:0] 00000000 */ |
| 0x0028, /* AICCFIXFREQ2[23:16] 00000000 */ |
| 0x0029, /* AICCFIXFREQ2[15:8] 00000000 */ |
| 0x002a, /* AICCFIXFREQ2[7:0] 00000000 */ |
| 0x002b, /* AICCFIXFREQ1[23:16] 00000000 */ |
| 0x002c, /* AICCFIXFREQ1[15:8] 00000000 */ |
| 0x002d, /* AICCFIXFREQ1[7:0] 00000000 */ |
| 0x002e, /* AICCFIXFREQ0[23:16] 00000000 */ |
| 0x002f, /* AICCFIXFREQ0[15:8] 00000000 */ |
| 0x0030, /* AICCFIXFREQ0[7:0] 00000000 */ |
| 0x0031, /* 1'b0 1'b1 1'b0 1'b0 x DAGC1STER */ |
| 0x0032, /* DAGC1STEN DAGC1STER */ |
| 0x0033, /* DAGC1STREF[15:8] 00001010 */ |
| 0x0034, /* DAGC1STREF[7:0] 11100100 */ |
| 0x0035, /* DAGC2NDE */ |
| 0x0036, /* DAGC2NDREF[15:8] 00001010 */ |
| 0x0037, /* DAGC2NDREF[7:0] 10000000 */ |
| 0x0038, /* DAGC2NDLOCKDETRNGSEL[1:0] */ |
| 0x003d, /* 1'b1 SAMGEARS */ |
| 0x0040, /* SAMLFGMA */ |
| 0x0041, /* SAMLFBWM */ |
| 0x0044, /* 1'b1 CRGEARSHE */ |
| 0x0045, /* CRLFGMAN */ |
| 0x0046, /* CFLFBWMA */ |
| 0x0047, /* CRLFGMAN */ |
| 0x0048, /* x x x x CRLFGSTEP_VS[3:0] xxxx1001 */ |
| 0x0049, /* CRLFBWMA */ |
| 0x004a, /* CRLFBWMA */ |
| 0x0050, /* 1'b0 1'b1 1'b1 1'b0 MSECALCDA */ |
| 0x0070, /* TPOUTEN TPIFEN TPCLKOUTE */ |
| 0x0071, /* TPSENB TPSSOPBITE */ |
| 0x0073, /* TP47HINS x x CHBERINT PERMODE[1:0] PERINT[1:0] 1xx11100 */ |
| 0x0075, /* x x x x x IQSWAPCTRL[2:0] xxxxx000 */ |
| 0x0076, /* NBERCON NBERST NBERPOL NBERWSYN */ |
| 0x0077, /* x NBERLOSTTH[2:0] NBERACQTH[3:0] x0000000 */ |
| 0x0078, /* NBERPOLY[31:24] 00000000 */ |
| 0x0079, /* NBERPOLY[23:16] 00000000 */ |
| 0x007a, /* NBERPOLY[15:8] 00000000 */ |
| 0x007b, /* NBERPOLY[7:0] 00000000 */ |
| 0x007c, /* NBERPED[31:24] 00000000 */ |
| 0x007d, /* NBERPED[23:16] 00000000 */ |
| 0x007e, /* NBERPED[15:8] 00000000 */ |
| 0x007f, /* NBERPED[7:0] 00000000 */ |
| 0x0080, /* x AGCLOCK DAGCLOCK SYSLOCK x x NEVERLOCK[1:0] */ |
| 0x0085, /* SPECINVST */ |
| 0x0088, /* SYSLOCKTIME[15:8] */ |
| 0x0089, /* SYSLOCKTIME[7:0] */ |
| 0x008c, /* FECLOCKTIME[15:8] */ |
| 0x008d, /* FECLOCKTIME[7:0] */ |
| 0x008e, /* AGCACCOUT[15:8] */ |
| 0x008f, /* AGCACCOUT[7:0] */ |
| 0x0090, /* AICCREJSTATUS[3:0] AICCREJBUSY[3:0] */ |
| 0x0091, /* AICCVSYNC */ |
| 0x009c, /* CARRFREQOFFSET[15:8] */ |
| 0x009d, /* CARRFREQOFFSET[7:0] */ |
| 0x00a1, /* SAMFREQOFFSET[23:16] */ |
| 0x00a2, /* SAMFREQOFFSET[15:8] */ |
| 0x00a3, /* SAMFREQOFFSET[7:0] */ |
| 0x00a6, /* SYNCLOCK SYNCLOCKH */ |
| #if 0 /* covered elsewhere */ |
| 0x00e8, /* CONSTPWR[15:8] */ |
| 0x00e9, /* CONSTPWR[7:0] */ |
| 0x00ea, /* BMSE[15:8] */ |
| 0x00eb, /* BMSE[7:0] */ |
| 0x00ec, /* MSE[15:8] */ |
| 0x00ed, /* MSE[7:0] */ |
| 0x00ee, /* CONSTI[7:0] */ |
| 0x00ef, /* CONSTQ[7:0] */ |
| #endif |
| 0x00f4, /* TPIFTPERRCNT[7:0] */ |
| 0x00f5, /* TPCORREC */ |
| 0x00f6, /* VBBER[15:8] */ |
| 0x00f7, /* VBBER[7:0] */ |
| 0x00f8, /* VABER[15:8] */ |
| 0x00f9, /* VABER[7:0] */ |
| 0x00fa, /* TPERRCNT[7:0] */ |
| 0x00fb, /* NBERLOCK x x x x x x x */ |
| 0x00fc, /* NBERVALUE[31:24] */ |
| 0x00fd, /* NBERVALUE[23:16] */ |
| 0x00fe, /* NBERVALUE[15:8] */ |
| 0x00ff, /* NBERVALUE[7:0] */ |
| 0x1000, /* 1'b0 WODAGCOU */ |
| 0x1005, /* x x 1'b1 1'b1 x SRD_Q_QM */ |
| 0x1009, /* SRDWAITTIME[7:0] (10msec) 00100011 */ |
| 0x100a, /* SRDWAITTIME_CQS[7:0] (msec) 01100100 */ |
| 0x101a, /* x 1'b1 1'b0 1'b0 x QMDQAMMODE[2:0] x100x010 */ |
| 0x1036, /* 1'b0 1'b1 1'b0 1'b0 SAMGSEND_CQS[3:0] 01001110 */ |
| 0x103c, /* SAMGSAUTOSTL_V[3:0] SAMGSAUTOEDL_V[3:0] 01000110 */ |
| 0x103d, /* 1'b1 1'b1 SAMCNORMBP_V[1:0] 1'b0 1'b0 SAMMODESEL_V[1:0] 11100001 */ |
| 0x103f, /* SAMZTEDSE */ |
| 0x105d, /* EQSTATUSE */ |
| 0x105f, /* x PMAPG2_V[2:0] x DMAPG2_V[2:0] x001x011 */ |
| 0x1060, /* 1'b1 EQSTATUSE */ |
| 0x1061, /* CRMAPBWSTL_V[3:0] CRMAPBWEDL_V[3:0] 00000100 */ |
| 0x1065, /* 1'b0 x CRMODE_V[1:0] 1'b1 x 1'b1 x 0x111x1x */ |
| 0x1066, /* 1'b0 1'b0 1'b1 1'b0 1'b1 PNBOOSTSE */ |
| 0x1068, /* CREPHNGAIN2_V[3:0] CREPHNPBW_V[3:0] 10010001 */ |
| 0x106e, /* x x x x x CREPHNEN_ */ |
| 0x106f, /* CREPHNTH_V[7:0] 00010101 */ |
| 0x1072, /* CRSWEEPN */ |
| 0x1073, /* CRPGAIN_V[3:0] x x 1'b1 1'b1 1001xx11 */ |
| 0x1074, /* CRPBW_V[3:0] x x 1'b1 1'b1 0001xx11 */ |
| 0x1080, /* DAFTSTATUS[1:0] x x x x x x */ |
| 0x1081, /* SRDSTATUS[1:0] x x x x x SRDLOCK */ |
| 0x10a9, /* EQSTATUS_CQS[1:0] x x x x x x */ |
| 0x10b7, /* EQSTATUS_V[1:0] x x x x x x */ |
| #if 0 /* SMART_ANT */ |
| 0x1f00, /* MODEDETE */ |
| 0x1f01, /* x x x x x x x SFNRST xxxxxxx0 */ |
| 0x1f03, /* NUMOFANT[7:0] 10000000 */ |
| 0x1f04, /* x SELMASK[6:0] x0000000 */ |
| 0x1f05, /* x SETMASK[6:0] x0000000 */ |
| 0x1f06, /* x TXDATA[6:0] x0000000 */ |
| 0x1f07, /* x CHNUMBER[6:0] x0000000 */ |
| 0x1f09, /* AGCTIME[23:16] 10011000 */ |
| 0x1f0a, /* AGCTIME[15:8] 10010110 */ |
| 0x1f0b, /* AGCTIME[7:0] 10000000 */ |
| 0x1f0c, /* ANTTIME[31:24] 00000000 */ |
| 0x1f0d, /* ANTTIME[23:16] 00000011 */ |
| 0x1f0e, /* ANTTIME[15:8] 10010000 */ |
| 0x1f0f, /* ANTTIME[7:0] 10010000 */ |
| 0x1f11, /* SYNCTIME[23:16] 10011000 */ |
| 0x1f12, /* SYNCTIME[15:8] 10010110 */ |
| 0x1f13, /* SYNCTIME[7:0] 10000000 */ |
| 0x1f14, /* SNRTIME[31:24] 00000001 */ |
| 0x1f15, /* SNRTIME[23:16] 01111101 */ |
| 0x1f16, /* SNRTIME[15:8] 01111000 */ |
| 0x1f17, /* SNRTIME[7:0] 01000000 */ |
| 0x1f19, /* FECTIME[23:16] 00000000 */ |
| 0x1f1a, /* FECTIME[15:8] 01110010 */ |
| 0x1f1b, /* FECTIME[7:0] 01110000 */ |
| 0x1f1d, /* FECTHD[7:0] 00000011 */ |
| 0x1f1f, /* SNRTHD[23:16] 00001000 */ |
| 0x1f20, /* SNRTHD[15:8] 01111111 */ |
| 0x1f21, /* SNRTHD[7:0] 10000101 */ |
| 0x1f80, /* IRQFLG x x SFSDRFLG MODEBFLG SAVEFLG SCANFLG TRACKFLG */ |
| 0x1f81, /* x SYNCCON SNRCON FECCON x STDBUSY SYNCRST AGCFZCO */ |
| 0x1f82, /* x x x SCANOPCD[4:0] */ |
| 0x1f83, /* x x x x MAINOPCD[3:0] */ |
| 0x1f84, /* x x RXDATA[13:8] */ |
| 0x1f85, /* RXDATA[7:0] */ |
| 0x1f86, /* x x SDTDATA[13:8] */ |
| 0x1f87, /* SDTDATA[7:0] */ |
| 0x1f89, /* ANTSNR[23:16] */ |
| 0x1f8a, /* ANTSNR[15:8] */ |
| 0x1f8b, /* ANTSNR[7:0] */ |
| 0x1f8c, /* x x x x ANTFEC[13:8] */ |
| 0x1f8d, /* ANTFEC[7:0] */ |
| 0x1f8e, /* MAXCNT[7:0] */ |
| 0x1f8f, /* SCANCNT[7:0] */ |
| 0x1f91, /* MAXPW[23:16] */ |
| 0x1f92, /* MAXPW[15:8] */ |
| 0x1f93, /* MAXPW[7:0] */ |
| 0x1f95, /* CURPWMSE[23:16] */ |
| 0x1f96, /* CURPWMSE[15:8] */ |
| 0x1f97, /* CURPWMSE[7:0] */ |
| #endif /* SMART_ANT */ |
| 0x211f, /* 1'b1 1'b1 1'b1 CIRQEN x x 1'b0 1'b0 1111xx00 */ |
| 0x212a, /* EQAUTOST */ |
| 0x2122, /* CHFAST[7:0] 01100000 */ |
| 0x212b, /* FFFSTEP_V[3:0] x FBFSTEP_V[2:0] 0001x001 */ |
| 0x212c, /* PHDEROTBWSEL[3:0] 1'b1 1'b1 1'b1 1'b0 10001110 */ |
| 0x212d, /* 1'b1 1'b1 1'b1 1'b1 x x TPIFLOCKS */ |
| 0x2135, /* DYNTRACKFDEQ[3:0] x 1'b0 1'b0 1'b0 1010x000 */ |
| 0x2141, /* TRMODE[1:0] 1'b1 1'b1 1'b0 1'b1 1'b1 1'b1 01110111 */ |
| 0x2162, /* AICCCTRLE */ |
| 0x2173, /* PHNCNFCNT[7:0] 00000100 */ |
| 0x2179, /* 1'b0 1'b0 1'b0 1'b1 x BADSINGLEDYNTRACKFBF[2:0] 0001x001 */ |
| 0x217a, /* 1'b0 1'b0 1'b0 1'b1 x BADSLOWSINGLEDYNTRACKFBF[2:0] 0001x001 */ |
| 0x217e, /* CNFCNTTPIF[7:0] 00001000 */ |
| 0x217f, /* TPERRCNTTPIF[7:0] 00000001 */ |
| 0x2180, /* x x x x x x FBDLYCIR[9:8] */ |
| 0x2181, /* FBDLYCIR[7:0] */ |
| 0x2185, /* MAXPWRMAIN[7:0] */ |
| 0x2191, /* NCOMBDET x x x x x x x */ |
| 0x2199, /* x MAINSTRON */ |
| 0x219a, /* FFFEQSTEPOUT_V[3:0] FBFSTEPOUT_V[2:0] */ |
| 0x21a1, /* x x SNRREF[5:0] */ |
| 0x2845, /* 1'b0 1'b1 x x FFFSTEP_CQS[1:0] FFFCENTERTAP[1:0] 01xx1110 */ |
| 0x2846, /* 1'b0 x 1'b0 1'b1 FBFSTEP_CQS[1:0] 1'b1 1'b0 0x011110 */ |
| 0x2847, /* ENNOSIGDE */ |
| 0x2849, /* 1'b1 1'b1 NOUSENOSI */ |
| 0x284a, /* EQINITWAITTIME[7:0] 01100100 */ |
| 0x3000, /* 1'b1 1'b1 1'b1 x x x 1'b0 RPTRSTM */ |
| 0x3001, /* RPTRSTWAITTIME[7:0] (100msec) 00110010 */ |
| 0x3031, /* FRAMELOC */ |
| 0x3032, /* 1'b1 1'b0 1'b0 1'b0 x x FRAMELOCKMODE_CQS[1:0] 1000xx11 */ |
| 0x30a9, /* VDLOCK_Q FRAMELOCK */ |
| 0x30aa, /* MPEGLOCK */ |
| }; |
| |
| #define numDumpRegs (ARRAY_SIZE(regtab)) |
| static u8 regval1[numDumpRegs] = {0, }; |
| static u8 regval2[numDumpRegs] = {0, }; |
| |
| static void lgdt3306a_DumpAllRegs(struct lgdt3306a_state *state) |
| { |
| memset(regval2, 0xff, sizeof(regval2)); |
| lgdt3306a_DumpRegs(state); |
| } |
| |
| static void lgdt3306a_DumpRegs(struct lgdt3306a_state *state) |
| { |
| int i; |
| int sav_debug = debug; |
| |
| if ((debug & DBG_DUMP) == 0) |
| return; |
| debug &= ~DBG_REG; /* suppress DBG_REG during reg dump */ |
| |
| lg_debug("\n"); |
| |
| for (i = 0; i < numDumpRegs; i++) { |
| lgdt3306a_read_reg(state, regtab[i], ®val1[i]); |
| if (regval1[i] != regval2[i]) { |
| lg_debug(" %04X = %02X\n", regtab[i], regval1[i]); |
| regval2[i] = regval1[i]; |
| } |
| } |
| debug = sav_debug; |
| } |
| #endif /* DBG_DUMP */ |
| |
| |
| |
| static const struct dvb_frontend_ops lgdt3306a_ops = { |
| .delsys = { SYS_ATSC, SYS_DVBC_ANNEX_B }, |
| .info = { |
| .name = "LG Electronics LGDT3306A VSB/QAM Frontend", |
| .frequency_min_hz = 54 * MHz, |
| .frequency_max_hz = 858 * MHz, |
| .frequency_stepsize_hz = 62500, |
| .caps = FE_CAN_QAM_AUTO | FE_CAN_QAM_64 | FE_CAN_QAM_256 | FE_CAN_8VSB |
| }, |
| .i2c_gate_ctrl = lgdt3306a_i2c_gate_ctrl, |
| .init = lgdt3306a_init, |
| .sleep = lgdt3306a_fe_sleep, |
| /* if this is set, it overrides the default swzigzag */ |
| .tune = lgdt3306a_tune, |
| .set_frontend = lgdt3306a_set_parameters, |
| .get_frontend = lgdt3306a_get_frontend, |
| .get_frontend_algo = lgdt3306a_get_frontend_algo, |
| .get_tune_settings = lgdt3306a_get_tune_settings, |
| .read_status = lgdt3306a_read_status, |
| .read_ber = lgdt3306a_read_ber, |
| .read_signal_strength = lgdt3306a_read_signal_strength, |
| .read_snr = lgdt3306a_read_snr, |
| .read_ucblocks = lgdt3306a_read_ucblocks, |
| .release = lgdt3306a_release, |
| .ts_bus_ctrl = lgdt3306a_ts_bus_ctrl, |
| .search = lgdt3306a_search, |
| }; |
| |
| static int lgdt3306a_select(struct i2c_mux_core *muxc, u32 chan) |
| { |
| struct i2c_client *client = i2c_mux_priv(muxc); |
| struct lgdt3306a_state *state = i2c_get_clientdata(client); |
| |
| return lgdt3306a_i2c_gate_ctrl(&state->frontend, 1); |
| } |
| |
| static int lgdt3306a_deselect(struct i2c_mux_core *muxc, u32 chan) |
| { |
| struct i2c_client *client = i2c_mux_priv(muxc); |
| struct lgdt3306a_state *state = i2c_get_clientdata(client); |
| |
| return lgdt3306a_i2c_gate_ctrl(&state->frontend, 0); |
| } |
| |
| static int lgdt3306a_probe(struct i2c_client *client) |
| { |
| struct lgdt3306a_config *config; |
| struct lgdt3306a_state *state; |
| struct dvb_frontend *fe; |
| int ret; |
| |
| if (!client->dev.platform_data) { |
| dev_err(&client->dev, "platform data is mandatory\n"); |
| return -EINVAL; |
| } |
| |
| config = kmemdup(client->dev.platform_data, |
| sizeof(struct lgdt3306a_config), GFP_KERNEL); |
| if (config == NULL) { |
| ret = -ENOMEM; |
| goto fail; |
| } |
| |
| config->i2c_addr = client->addr; |
| fe = lgdt3306a_attach(config, client->adapter); |
| if (fe == NULL) { |
| ret = -ENODEV; |
| goto err_fe; |
| } |
| |
| i2c_set_clientdata(client, fe->demodulator_priv); |
| state = fe->demodulator_priv; |
| state->frontend.ops.release = NULL; |
| |
| /* create mux i2c adapter for tuner */ |
| state->muxc = i2c_mux_alloc(client->adapter, &client->dev, |
| 1, 0, I2C_MUX_LOCKED, |
| lgdt3306a_select, lgdt3306a_deselect); |
| if (!state->muxc) { |
| ret = -ENOMEM; |
| goto err_kfree; |
| } |
| state->muxc->priv = client; |
| ret = i2c_mux_add_adapter(state->muxc, 0, 0); |
| if (ret) |
| goto err_kfree; |
| |
| /* create dvb_frontend */ |
| fe->ops.i2c_gate_ctrl = NULL; |
| *config->i2c_adapter = state->muxc->adapter[0]; |
| *config->fe = fe; |
| |
| dev_info(&client->dev, "LG Electronics LGDT3306A successfully identified\n"); |
| |
| return 0; |
| |
| err_kfree: |
| kfree(state); |
| err_fe: |
| kfree(config); |
| fail: |
| dev_warn(&client->dev, "probe failed = %d\n", ret); |
| return ret; |
| } |
| |
| static void lgdt3306a_remove(struct i2c_client *client) |
| { |
| struct lgdt3306a_state *state = i2c_get_clientdata(client); |
| |
| i2c_mux_del_adapters(state->muxc); |
| |
| state->frontend.ops.release = NULL; |
| state->frontend.demodulator_priv = NULL; |
| |
| kfree(state->cfg); |
| kfree(state); |
| } |
| |
| static const struct i2c_device_id lgdt3306a_id_table[] = { |
| {"lgdt3306a", 0}, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, lgdt3306a_id_table); |
| |
| static struct i2c_driver lgdt3306a_driver = { |
| .driver = { |
| .name = "lgdt3306a", |
| .suppress_bind_attrs = true, |
| }, |
| .probe = lgdt3306a_probe, |
| .remove = lgdt3306a_remove, |
| .id_table = lgdt3306a_id_table, |
| }; |
| |
| module_i2c_driver(lgdt3306a_driver); |
| |
| MODULE_DESCRIPTION("LG Electronics LGDT3306A ATSC/QAM-B Demodulator Driver"); |
| MODULE_AUTHOR("Fred Richter <frichter@hauppauge.com>"); |
| MODULE_LICENSE("GPL"); |
| MODULE_VERSION("0.2"); |