| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * SPI-Engine SPI controller driver |
| * Copyright 2015 Analog Devices Inc. |
| * Author: Lars-Peter Clausen <lars@metafoo.de> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/completion.h> |
| #include <linux/fpga/adi-axi-common.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/of.h> |
| #include <linux/module.h> |
| #include <linux/overflow.h> |
| #include <linux/platform_device.h> |
| #include <linux/spi/spi.h> |
| |
| #define SPI_ENGINE_REG_RESET 0x40 |
| |
| #define SPI_ENGINE_REG_INT_ENABLE 0x80 |
| #define SPI_ENGINE_REG_INT_PENDING 0x84 |
| #define SPI_ENGINE_REG_INT_SOURCE 0x88 |
| |
| #define SPI_ENGINE_REG_SYNC_ID 0xc0 |
| |
| #define SPI_ENGINE_REG_CMD_FIFO_ROOM 0xd0 |
| #define SPI_ENGINE_REG_SDO_FIFO_ROOM 0xd4 |
| #define SPI_ENGINE_REG_SDI_FIFO_LEVEL 0xd8 |
| |
| #define SPI_ENGINE_REG_CMD_FIFO 0xe0 |
| #define SPI_ENGINE_REG_SDO_DATA_FIFO 0xe4 |
| #define SPI_ENGINE_REG_SDI_DATA_FIFO 0xe8 |
| #define SPI_ENGINE_REG_SDI_DATA_FIFO_PEEK 0xec |
| |
| #define SPI_ENGINE_INT_CMD_ALMOST_EMPTY BIT(0) |
| #define SPI_ENGINE_INT_SDO_ALMOST_EMPTY BIT(1) |
| #define SPI_ENGINE_INT_SDI_ALMOST_FULL BIT(2) |
| #define SPI_ENGINE_INT_SYNC BIT(3) |
| |
| #define SPI_ENGINE_CONFIG_CPHA BIT(0) |
| #define SPI_ENGINE_CONFIG_CPOL BIT(1) |
| #define SPI_ENGINE_CONFIG_3WIRE BIT(2) |
| |
| #define SPI_ENGINE_INST_TRANSFER 0x0 |
| #define SPI_ENGINE_INST_ASSERT 0x1 |
| #define SPI_ENGINE_INST_WRITE 0x2 |
| #define SPI_ENGINE_INST_MISC 0x3 |
| #define SPI_ENGINE_INST_CS_INV 0x4 |
| |
| #define SPI_ENGINE_CMD_REG_CLK_DIV 0x0 |
| #define SPI_ENGINE_CMD_REG_CONFIG 0x1 |
| #define SPI_ENGINE_CMD_REG_XFER_BITS 0x2 |
| |
| #define SPI_ENGINE_MISC_SYNC 0x0 |
| #define SPI_ENGINE_MISC_SLEEP 0x1 |
| |
| #define SPI_ENGINE_TRANSFER_WRITE 0x1 |
| #define SPI_ENGINE_TRANSFER_READ 0x2 |
| |
| /* Arbitrary sync ID for use by host->cur_msg */ |
| #define AXI_SPI_ENGINE_CUR_MSG_SYNC_ID 0x1 |
| |
| #define SPI_ENGINE_CMD(inst, arg1, arg2) \ |
| (((inst) << 12) | ((arg1) << 8) | (arg2)) |
| |
| #define SPI_ENGINE_CMD_TRANSFER(flags, n) \ |
| SPI_ENGINE_CMD(SPI_ENGINE_INST_TRANSFER, (flags), (n)) |
| #define SPI_ENGINE_CMD_ASSERT(delay, cs) \ |
| SPI_ENGINE_CMD(SPI_ENGINE_INST_ASSERT, (delay), (cs)) |
| #define SPI_ENGINE_CMD_WRITE(reg, val) \ |
| SPI_ENGINE_CMD(SPI_ENGINE_INST_WRITE, (reg), (val)) |
| #define SPI_ENGINE_CMD_SLEEP(delay) \ |
| SPI_ENGINE_CMD(SPI_ENGINE_INST_MISC, SPI_ENGINE_MISC_SLEEP, (delay)) |
| #define SPI_ENGINE_CMD_SYNC(id) \ |
| SPI_ENGINE_CMD(SPI_ENGINE_INST_MISC, SPI_ENGINE_MISC_SYNC, (id)) |
| #define SPI_ENGINE_CMD_CS_INV(flags) \ |
| SPI_ENGINE_CMD(SPI_ENGINE_INST_CS_INV, 0, (flags)) |
| |
| struct spi_engine_program { |
| unsigned int length; |
| uint16_t instructions[] __counted_by(length); |
| }; |
| |
| /** |
| * struct spi_engine_message_state - SPI engine per-message state |
| */ |
| struct spi_engine_message_state { |
| /** @cmd_length: Number of elements in cmd_buf array. */ |
| unsigned cmd_length; |
| /** @cmd_buf: Array of commands not yet written to CMD FIFO. */ |
| const uint16_t *cmd_buf; |
| /** @tx_xfer: Next xfer with tx_buf not yet fully written to TX FIFO. */ |
| struct spi_transfer *tx_xfer; |
| /** @tx_length: Size of tx_buf in bytes. */ |
| unsigned int tx_length; |
| /** @tx_buf: Bytes not yet written to TX FIFO. */ |
| const uint8_t *tx_buf; |
| /** @rx_xfer: Next xfer with rx_buf not yet fully written to RX FIFO. */ |
| struct spi_transfer *rx_xfer; |
| /** @rx_length: Size of tx_buf in bytes. */ |
| unsigned int rx_length; |
| /** @rx_buf: Bytes not yet written to the RX FIFO. */ |
| uint8_t *rx_buf; |
| }; |
| |
| struct spi_engine { |
| struct clk *clk; |
| struct clk *ref_clk; |
| |
| spinlock_t lock; |
| |
| void __iomem *base; |
| struct spi_engine_message_state msg_state; |
| struct completion msg_complete; |
| unsigned int int_enable; |
| /* shadows hardware CS inversion flag state */ |
| u8 cs_inv; |
| }; |
| |
| static void spi_engine_program_add_cmd(struct spi_engine_program *p, |
| bool dry, uint16_t cmd) |
| { |
| p->length++; |
| |
| if (!dry) |
| p->instructions[p->length - 1] = cmd; |
| } |
| |
| static unsigned int spi_engine_get_config(struct spi_device *spi) |
| { |
| unsigned int config = 0; |
| |
| if (spi->mode & SPI_CPOL) |
| config |= SPI_ENGINE_CONFIG_CPOL; |
| if (spi->mode & SPI_CPHA) |
| config |= SPI_ENGINE_CONFIG_CPHA; |
| if (spi->mode & SPI_3WIRE) |
| config |= SPI_ENGINE_CONFIG_3WIRE; |
| |
| return config; |
| } |
| |
| static void spi_engine_gen_xfer(struct spi_engine_program *p, bool dry, |
| struct spi_transfer *xfer) |
| { |
| unsigned int len; |
| |
| if (xfer->bits_per_word <= 8) |
| len = xfer->len; |
| else if (xfer->bits_per_word <= 16) |
| len = xfer->len / 2; |
| else |
| len = xfer->len / 4; |
| |
| while (len) { |
| unsigned int n = min(len, 256U); |
| unsigned int flags = 0; |
| |
| if (xfer->tx_buf) |
| flags |= SPI_ENGINE_TRANSFER_WRITE; |
| if (xfer->rx_buf) |
| flags |= SPI_ENGINE_TRANSFER_READ; |
| |
| spi_engine_program_add_cmd(p, dry, |
| SPI_ENGINE_CMD_TRANSFER(flags, n - 1)); |
| len -= n; |
| } |
| } |
| |
| static void spi_engine_gen_sleep(struct spi_engine_program *p, bool dry, |
| int delay_ns, int inst_ns, u32 sclk_hz) |
| { |
| unsigned int t; |
| |
| /* |
| * Negative delay indicates error, e.g. from spi_delay_to_ns(). And if |
| * delay is less that the instruction execution time, there is no need |
| * for an extra sleep instruction since the instruction execution time |
| * will already cover the required delay. |
| */ |
| if (delay_ns < 0 || delay_ns <= inst_ns) |
| return; |
| |
| t = DIV_ROUND_UP_ULL((u64)(delay_ns - inst_ns) * sclk_hz, NSEC_PER_SEC); |
| while (t) { |
| unsigned int n = min(t, 256U); |
| |
| spi_engine_program_add_cmd(p, dry, SPI_ENGINE_CMD_SLEEP(n - 1)); |
| t -= n; |
| } |
| } |
| |
| static void spi_engine_gen_cs(struct spi_engine_program *p, bool dry, |
| struct spi_device *spi, bool assert) |
| { |
| unsigned int mask = 0xff; |
| |
| if (assert) |
| mask ^= BIT(spi_get_chipselect(spi, 0)); |
| |
| spi_engine_program_add_cmd(p, dry, SPI_ENGINE_CMD_ASSERT(0, mask)); |
| } |
| |
| /* |
| * Performs precompile steps on the message. |
| * |
| * The SPI core does most of the message/transfer validation and filling in |
| * fields for us via __spi_validate(). This fixes up anything remaining not |
| * done there. |
| * |
| * NB: This is separate from spi_engine_compile_message() because the latter |
| * is called twice and would otherwise result in double-evaluation. |
| */ |
| static void spi_engine_precompile_message(struct spi_message *msg) |
| { |
| unsigned int clk_div, max_hz = msg->spi->controller->max_speed_hz; |
| struct spi_transfer *xfer; |
| |
| list_for_each_entry(xfer, &msg->transfers, transfer_list) { |
| clk_div = DIV_ROUND_UP(max_hz, xfer->speed_hz); |
| xfer->effective_speed_hz = max_hz / min(clk_div, 256U); |
| } |
| } |
| |
| static void spi_engine_compile_message(struct spi_message *msg, bool dry, |
| struct spi_engine_program *p) |
| { |
| struct spi_device *spi = msg->spi; |
| struct spi_controller *host = spi->controller; |
| struct spi_transfer *xfer; |
| int clk_div, new_clk_div, inst_ns; |
| bool keep_cs = false; |
| u8 bits_per_word = 0; |
| |
| /* |
| * Take into account instruction execution time for more accurate sleep |
| * times, especially when the delay is small. |
| */ |
| inst_ns = DIV_ROUND_UP(NSEC_PER_SEC, host->max_speed_hz); |
| |
| clk_div = 1; |
| |
| spi_engine_program_add_cmd(p, dry, |
| SPI_ENGINE_CMD_WRITE(SPI_ENGINE_CMD_REG_CONFIG, |
| spi_engine_get_config(spi))); |
| |
| xfer = list_first_entry(&msg->transfers, struct spi_transfer, transfer_list); |
| spi_engine_gen_cs(p, dry, spi, !xfer->cs_off); |
| |
| list_for_each_entry(xfer, &msg->transfers, transfer_list) { |
| new_clk_div = host->max_speed_hz / xfer->effective_speed_hz; |
| if (new_clk_div != clk_div) { |
| clk_div = new_clk_div; |
| /* actual divider used is register value + 1 */ |
| spi_engine_program_add_cmd(p, dry, |
| SPI_ENGINE_CMD_WRITE(SPI_ENGINE_CMD_REG_CLK_DIV, |
| clk_div - 1)); |
| } |
| |
| if (bits_per_word != xfer->bits_per_word) { |
| bits_per_word = xfer->bits_per_word; |
| spi_engine_program_add_cmd(p, dry, |
| SPI_ENGINE_CMD_WRITE(SPI_ENGINE_CMD_REG_XFER_BITS, |
| bits_per_word)); |
| } |
| |
| spi_engine_gen_xfer(p, dry, xfer); |
| spi_engine_gen_sleep(p, dry, spi_delay_to_ns(&xfer->delay, xfer), |
| inst_ns, xfer->effective_speed_hz); |
| |
| if (xfer->cs_change) { |
| if (list_is_last(&xfer->transfer_list, &msg->transfers)) { |
| keep_cs = true; |
| } else { |
| if (!xfer->cs_off) |
| spi_engine_gen_cs(p, dry, spi, false); |
| |
| spi_engine_gen_sleep(p, dry, spi_delay_to_ns( |
| &xfer->cs_change_delay, xfer), inst_ns, |
| xfer->effective_speed_hz); |
| |
| if (!list_next_entry(xfer, transfer_list)->cs_off) |
| spi_engine_gen_cs(p, dry, spi, true); |
| } |
| } else if (!list_is_last(&xfer->transfer_list, &msg->transfers) && |
| xfer->cs_off != list_next_entry(xfer, transfer_list)->cs_off) { |
| spi_engine_gen_cs(p, dry, spi, xfer->cs_off); |
| } |
| } |
| |
| if (!keep_cs) |
| spi_engine_gen_cs(p, dry, spi, false); |
| |
| /* |
| * Restore clockdiv to default so that future gen_sleep commands don't |
| * have to be aware of the current register state. |
| */ |
| if (clk_div != 1) |
| spi_engine_program_add_cmd(p, dry, |
| SPI_ENGINE_CMD_WRITE(SPI_ENGINE_CMD_REG_CLK_DIV, 0)); |
| } |
| |
| static void spi_engine_xfer_next(struct spi_message *msg, |
| struct spi_transfer **_xfer) |
| { |
| struct spi_transfer *xfer = *_xfer; |
| |
| if (!xfer) { |
| xfer = list_first_entry(&msg->transfers, |
| struct spi_transfer, transfer_list); |
| } else if (list_is_last(&xfer->transfer_list, &msg->transfers)) { |
| xfer = NULL; |
| } else { |
| xfer = list_next_entry(xfer, transfer_list); |
| } |
| |
| *_xfer = xfer; |
| } |
| |
| static void spi_engine_tx_next(struct spi_message *msg) |
| { |
| struct spi_engine_message_state *st = msg->state; |
| struct spi_transfer *xfer = st->tx_xfer; |
| |
| do { |
| spi_engine_xfer_next(msg, &xfer); |
| } while (xfer && !xfer->tx_buf); |
| |
| st->tx_xfer = xfer; |
| if (xfer) { |
| st->tx_length = xfer->len; |
| st->tx_buf = xfer->tx_buf; |
| } else { |
| st->tx_buf = NULL; |
| } |
| } |
| |
| static void spi_engine_rx_next(struct spi_message *msg) |
| { |
| struct spi_engine_message_state *st = msg->state; |
| struct spi_transfer *xfer = st->rx_xfer; |
| |
| do { |
| spi_engine_xfer_next(msg, &xfer); |
| } while (xfer && !xfer->rx_buf); |
| |
| st->rx_xfer = xfer; |
| if (xfer) { |
| st->rx_length = xfer->len; |
| st->rx_buf = xfer->rx_buf; |
| } else { |
| st->rx_buf = NULL; |
| } |
| } |
| |
| static bool spi_engine_write_cmd_fifo(struct spi_engine *spi_engine, |
| struct spi_message *msg) |
| { |
| void __iomem *addr = spi_engine->base + SPI_ENGINE_REG_CMD_FIFO; |
| struct spi_engine_message_state *st = msg->state; |
| unsigned int n, m, i; |
| const uint16_t *buf; |
| |
| n = readl_relaxed(spi_engine->base + SPI_ENGINE_REG_CMD_FIFO_ROOM); |
| while (n && st->cmd_length) { |
| m = min(n, st->cmd_length); |
| buf = st->cmd_buf; |
| for (i = 0; i < m; i++) |
| writel_relaxed(buf[i], addr); |
| st->cmd_buf += m; |
| st->cmd_length -= m; |
| n -= m; |
| } |
| |
| return st->cmd_length != 0; |
| } |
| |
| static bool spi_engine_write_tx_fifo(struct spi_engine *spi_engine, |
| struct spi_message *msg) |
| { |
| void __iomem *addr = spi_engine->base + SPI_ENGINE_REG_SDO_DATA_FIFO; |
| struct spi_engine_message_state *st = msg->state; |
| unsigned int n, m, i; |
| |
| n = readl_relaxed(spi_engine->base + SPI_ENGINE_REG_SDO_FIFO_ROOM); |
| while (n && st->tx_length) { |
| if (st->tx_xfer->bits_per_word <= 8) { |
| const u8 *buf = st->tx_buf; |
| |
| m = min(n, st->tx_length); |
| for (i = 0; i < m; i++) |
| writel_relaxed(buf[i], addr); |
| st->tx_buf += m; |
| st->tx_length -= m; |
| } else if (st->tx_xfer->bits_per_word <= 16) { |
| const u16 *buf = (const u16 *)st->tx_buf; |
| |
| m = min(n, st->tx_length / 2); |
| for (i = 0; i < m; i++) |
| writel_relaxed(buf[i], addr); |
| st->tx_buf += m * 2; |
| st->tx_length -= m * 2; |
| } else { |
| const u32 *buf = (const u32 *)st->tx_buf; |
| |
| m = min(n, st->tx_length / 4); |
| for (i = 0; i < m; i++) |
| writel_relaxed(buf[i], addr); |
| st->tx_buf += m * 4; |
| st->tx_length -= m * 4; |
| } |
| n -= m; |
| if (st->tx_length == 0) |
| spi_engine_tx_next(msg); |
| } |
| |
| return st->tx_length != 0; |
| } |
| |
| static bool spi_engine_read_rx_fifo(struct spi_engine *spi_engine, |
| struct spi_message *msg) |
| { |
| void __iomem *addr = spi_engine->base + SPI_ENGINE_REG_SDI_DATA_FIFO; |
| struct spi_engine_message_state *st = msg->state; |
| unsigned int n, m, i; |
| |
| n = readl_relaxed(spi_engine->base + SPI_ENGINE_REG_SDI_FIFO_LEVEL); |
| while (n && st->rx_length) { |
| if (st->rx_xfer->bits_per_word <= 8) { |
| u8 *buf = st->rx_buf; |
| |
| m = min(n, st->rx_length); |
| for (i = 0; i < m; i++) |
| buf[i] = readl_relaxed(addr); |
| st->rx_buf += m; |
| st->rx_length -= m; |
| } else if (st->rx_xfer->bits_per_word <= 16) { |
| u16 *buf = (u16 *)st->rx_buf; |
| |
| m = min(n, st->rx_length / 2); |
| for (i = 0; i < m; i++) |
| buf[i] = readl_relaxed(addr); |
| st->rx_buf += m * 2; |
| st->rx_length -= m * 2; |
| } else { |
| u32 *buf = (u32 *)st->rx_buf; |
| |
| m = min(n, st->rx_length / 4); |
| for (i = 0; i < m; i++) |
| buf[i] = readl_relaxed(addr); |
| st->rx_buf += m * 4; |
| st->rx_length -= m * 4; |
| } |
| n -= m; |
| if (st->rx_length == 0) |
| spi_engine_rx_next(msg); |
| } |
| |
| return st->rx_length != 0; |
| } |
| |
| static irqreturn_t spi_engine_irq(int irq, void *devid) |
| { |
| struct spi_controller *host = devid; |
| struct spi_message *msg = host->cur_msg; |
| struct spi_engine *spi_engine = spi_controller_get_devdata(host); |
| unsigned int disable_int = 0; |
| unsigned int pending; |
| int completed_id = -1; |
| |
| pending = readl_relaxed(spi_engine->base + SPI_ENGINE_REG_INT_PENDING); |
| |
| if (pending & SPI_ENGINE_INT_SYNC) { |
| writel_relaxed(SPI_ENGINE_INT_SYNC, |
| spi_engine->base + SPI_ENGINE_REG_INT_PENDING); |
| completed_id = readl_relaxed( |
| spi_engine->base + SPI_ENGINE_REG_SYNC_ID); |
| } |
| |
| spin_lock(&spi_engine->lock); |
| |
| if (pending & SPI_ENGINE_INT_CMD_ALMOST_EMPTY) { |
| if (!spi_engine_write_cmd_fifo(spi_engine, msg)) |
| disable_int |= SPI_ENGINE_INT_CMD_ALMOST_EMPTY; |
| } |
| |
| if (pending & SPI_ENGINE_INT_SDO_ALMOST_EMPTY) { |
| if (!spi_engine_write_tx_fifo(spi_engine, msg)) |
| disable_int |= SPI_ENGINE_INT_SDO_ALMOST_EMPTY; |
| } |
| |
| if (pending & (SPI_ENGINE_INT_SDI_ALMOST_FULL | SPI_ENGINE_INT_SYNC)) { |
| if (!spi_engine_read_rx_fifo(spi_engine, msg)) |
| disable_int |= SPI_ENGINE_INT_SDI_ALMOST_FULL; |
| } |
| |
| if (pending & SPI_ENGINE_INT_SYNC && msg) { |
| if (completed_id == AXI_SPI_ENGINE_CUR_MSG_SYNC_ID) { |
| msg->status = 0; |
| msg->actual_length = msg->frame_length; |
| complete(&spi_engine->msg_complete); |
| disable_int |= SPI_ENGINE_INT_SYNC; |
| } |
| } |
| |
| if (disable_int) { |
| spi_engine->int_enable &= ~disable_int; |
| writel_relaxed(spi_engine->int_enable, |
| spi_engine->base + SPI_ENGINE_REG_INT_ENABLE); |
| } |
| |
| spin_unlock(&spi_engine->lock); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int spi_engine_optimize_message(struct spi_message *msg) |
| { |
| struct spi_engine_program p_dry, *p; |
| |
| spi_engine_precompile_message(msg); |
| |
| p_dry.length = 0; |
| spi_engine_compile_message(msg, true, &p_dry); |
| |
| p = kzalloc(struct_size(p, instructions, p_dry.length + 1), GFP_KERNEL); |
| if (!p) |
| return -ENOMEM; |
| |
| spi_engine_compile_message(msg, false, p); |
| |
| spi_engine_program_add_cmd(p, false, SPI_ENGINE_CMD_SYNC( |
| AXI_SPI_ENGINE_CUR_MSG_SYNC_ID)); |
| |
| msg->opt_state = p; |
| |
| return 0; |
| } |
| |
| static int spi_engine_unoptimize_message(struct spi_message *msg) |
| { |
| kfree(msg->opt_state); |
| |
| return 0; |
| } |
| |
| static int spi_engine_setup(struct spi_device *device) |
| { |
| struct spi_controller *host = device->controller; |
| struct spi_engine *spi_engine = spi_controller_get_devdata(host); |
| |
| if (device->mode & SPI_CS_HIGH) |
| spi_engine->cs_inv |= BIT(spi_get_chipselect(device, 0)); |
| else |
| spi_engine->cs_inv &= ~BIT(spi_get_chipselect(device, 0)); |
| |
| writel_relaxed(SPI_ENGINE_CMD_CS_INV(spi_engine->cs_inv), |
| spi_engine->base + SPI_ENGINE_REG_CMD_FIFO); |
| |
| /* |
| * In addition to setting the flags, we have to do a CS assert command |
| * to make the new setting actually take effect. |
| */ |
| writel_relaxed(SPI_ENGINE_CMD_ASSERT(0, 0xff), |
| spi_engine->base + SPI_ENGINE_REG_CMD_FIFO); |
| |
| return 0; |
| } |
| |
| static int spi_engine_transfer_one_message(struct spi_controller *host, |
| struct spi_message *msg) |
| { |
| struct spi_engine *spi_engine = spi_controller_get_devdata(host); |
| struct spi_engine_message_state *st = &spi_engine->msg_state; |
| struct spi_engine_program *p = msg->opt_state; |
| unsigned int int_enable = 0; |
| unsigned long flags; |
| |
| /* reinitialize message state for this transfer */ |
| memset(st, 0, sizeof(*st)); |
| st->cmd_buf = p->instructions; |
| st->cmd_length = p->length; |
| msg->state = st; |
| |
| reinit_completion(&spi_engine->msg_complete); |
| |
| spin_lock_irqsave(&spi_engine->lock, flags); |
| |
| if (spi_engine_write_cmd_fifo(spi_engine, msg)) |
| int_enable |= SPI_ENGINE_INT_CMD_ALMOST_EMPTY; |
| |
| spi_engine_tx_next(msg); |
| if (spi_engine_write_tx_fifo(spi_engine, msg)) |
| int_enable |= SPI_ENGINE_INT_SDO_ALMOST_EMPTY; |
| |
| spi_engine_rx_next(msg); |
| if (st->rx_length != 0) |
| int_enable |= SPI_ENGINE_INT_SDI_ALMOST_FULL; |
| |
| int_enable |= SPI_ENGINE_INT_SYNC; |
| |
| writel_relaxed(int_enable, |
| spi_engine->base + SPI_ENGINE_REG_INT_ENABLE); |
| spi_engine->int_enable = int_enable; |
| spin_unlock_irqrestore(&spi_engine->lock, flags); |
| |
| if (!wait_for_completion_timeout(&spi_engine->msg_complete, |
| msecs_to_jiffies(5000))) { |
| dev_err(&host->dev, |
| "Timeout occurred while waiting for transfer to complete. Hardware is probably broken.\n"); |
| msg->status = -ETIMEDOUT; |
| } |
| |
| spi_finalize_current_message(host); |
| |
| return msg->status; |
| } |
| |
| static void spi_engine_release_hw(void *p) |
| { |
| struct spi_engine *spi_engine = p; |
| |
| writel_relaxed(0xff, spi_engine->base + SPI_ENGINE_REG_INT_PENDING); |
| writel_relaxed(0x00, spi_engine->base + SPI_ENGINE_REG_INT_ENABLE); |
| writel_relaxed(0x01, spi_engine->base + SPI_ENGINE_REG_RESET); |
| } |
| |
| static int spi_engine_probe(struct platform_device *pdev) |
| { |
| struct spi_engine *spi_engine; |
| struct spi_controller *host; |
| unsigned int version; |
| int irq; |
| int ret; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| host = devm_spi_alloc_host(&pdev->dev, sizeof(*spi_engine)); |
| if (!host) |
| return -ENOMEM; |
| |
| spi_engine = spi_controller_get_devdata(host); |
| |
| spin_lock_init(&spi_engine->lock); |
| init_completion(&spi_engine->msg_complete); |
| |
| spi_engine->clk = devm_clk_get_enabled(&pdev->dev, "s_axi_aclk"); |
| if (IS_ERR(spi_engine->clk)) |
| return PTR_ERR(spi_engine->clk); |
| |
| spi_engine->ref_clk = devm_clk_get_enabled(&pdev->dev, "spi_clk"); |
| if (IS_ERR(spi_engine->ref_clk)) |
| return PTR_ERR(spi_engine->ref_clk); |
| |
| spi_engine->base = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(spi_engine->base)) |
| return PTR_ERR(spi_engine->base); |
| |
| version = readl(spi_engine->base + ADI_AXI_REG_VERSION); |
| if (ADI_AXI_PCORE_VER_MAJOR(version) != 1) { |
| dev_err(&pdev->dev, "Unsupported peripheral version %u.%u.%u\n", |
| ADI_AXI_PCORE_VER_MAJOR(version), |
| ADI_AXI_PCORE_VER_MINOR(version), |
| ADI_AXI_PCORE_VER_PATCH(version)); |
| return -ENODEV; |
| } |
| |
| writel_relaxed(0x00, spi_engine->base + SPI_ENGINE_REG_RESET); |
| writel_relaxed(0xff, spi_engine->base + SPI_ENGINE_REG_INT_PENDING); |
| writel_relaxed(0x00, spi_engine->base + SPI_ENGINE_REG_INT_ENABLE); |
| |
| ret = devm_add_action_or_reset(&pdev->dev, spi_engine_release_hw, |
| spi_engine); |
| if (ret) |
| return ret; |
| |
| ret = devm_request_irq(&pdev->dev, irq, spi_engine_irq, 0, pdev->name, |
| host); |
| if (ret) |
| return ret; |
| |
| host->dev.of_node = pdev->dev.of_node; |
| host->mode_bits = SPI_CPOL | SPI_CPHA | SPI_3WIRE; |
| host->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32); |
| host->max_speed_hz = clk_get_rate(spi_engine->ref_clk) / 2; |
| host->transfer_one_message = spi_engine_transfer_one_message; |
| host->optimize_message = spi_engine_optimize_message; |
| host->unoptimize_message = spi_engine_unoptimize_message; |
| host->num_chipselect = 8; |
| |
| /* Some features depend of the IP core version. */ |
| if (ADI_AXI_PCORE_VER_MINOR(version) >= 2) { |
| host->mode_bits |= SPI_CS_HIGH; |
| host->setup = spi_engine_setup; |
| } |
| |
| if (host->max_speed_hz == 0) |
| return dev_err_probe(&pdev->dev, -EINVAL, "spi_clk rate is 0"); |
| |
| return devm_spi_register_controller(&pdev->dev, host); |
| } |
| |
| static const struct of_device_id spi_engine_match_table[] = { |
| { .compatible = "adi,axi-spi-engine-1.00.a" }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, spi_engine_match_table); |
| |
| static struct platform_driver spi_engine_driver = { |
| .probe = spi_engine_probe, |
| .driver = { |
| .name = "spi-engine", |
| .of_match_table = spi_engine_match_table, |
| }, |
| }; |
| module_platform_driver(spi_engine_driver); |
| |
| MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>"); |
| MODULE_DESCRIPTION("Analog Devices SPI engine peripheral driver"); |
| MODULE_LICENSE("GPL"); |