// SPDX-License-Identifier: GPL-2.0
/*
 * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
 */

/dts-v1/;

#include "k3-j721e-som-p0.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/net/ti-dp83867.h>
#include <dt-bindings/phy/phy-cadence.h>

/ {
	compatible = "ti,j721e-evm", "ti,j721e";
	model = "Texas Instruments J721e EVM";

	chosen {
		stdout-path = "serial2:115200n8";
		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
	};

	gpio_keys: gpio-keys {
		compatible = "gpio-keys";
		autorepeat;
		pinctrl-names = "default";
		pinctrl-0 = <&sw10_button_pins_default &sw11_button_pins_default>;

		sw10: switch-10 {
			label = "GPIO Key USER1";
			linux,code = <BTN_0>;
			gpios = <&main_gpio0 0 GPIO_ACTIVE_LOW>;
		};

		sw11: switch-11 {
			label = "GPIO Key USER2";
			linux,code = <BTN_1>;
			gpios = <&wkup_gpio0 7 GPIO_ACTIVE_LOW>;
		};
	};

	evm_12v0: fixedregulator-evm12v0 {
		/* main supply */
		compatible = "regulator-fixed";
		regulator-name = "evm_12v0";
		regulator-min-microvolt = <12000000>;
		regulator-max-microvolt = <12000000>;
		regulator-always-on;
		regulator-boot-on;
	};

	vsys_3v3: fixedregulator-vsys3v3 {
		/* Output of LMS140 */
		compatible = "regulator-fixed";
		regulator-name = "vsys_3v3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&evm_12v0>;
		regulator-always-on;
		regulator-boot-on;
	};

	vsys_5v0: fixedregulator-vsys5v0 {
		/* Output of LM5140 */
		compatible = "regulator-fixed";
		regulator-name = "vsys_5v0";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		vin-supply = <&evm_12v0>;
		regulator-always-on;
		regulator-boot-on;
	};

	vdd_mmc1: fixedregulator-sd {
		compatible = "regulator-fixed";
		regulator-name = "vdd_mmc1";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		enable-active-high;
		vin-supply = <&vsys_3v3>;
		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
	};

	vdd_sd_dv_alt: gpio-regulator-TLV71033 {
		compatible = "regulator-gpio";
		pinctrl-names = "default";
		pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
		regulator-name = "tlv71033";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		vin-supply = <&vsys_5v0>;
		gpios = <&main_gpio0 117 GPIO_ACTIVE_HIGH>;
		states = <1800000 0x0>,
			 <3300000 0x1>;
	};

	sound0: sound-0 {
		compatible = "ti,j721e-cpb-audio";
		model = "j721e-cpb";

		ti,cpb-mcasp = <&mcasp10>;
		ti,cpb-codec = <&pcm3168a_1>;

		clocks = <&k3_clks 184 1>,
			 <&k3_clks 184 2>, <&k3_clks 184 4>,
			 <&k3_clks 157 371>,
			 <&k3_clks 157 400>, <&k3_clks 157 401>;
		clock-names = "cpb-mcasp-auxclk",
			      "cpb-mcasp-auxclk-48000", "cpb-mcasp-auxclk-44100",
			      "cpb-codec-scki",
			      "cpb-codec-scki-48000", "cpb-codec-scki-44100";
	};

	transceiver1: can-phy0 {
		compatible = "ti,tcan1043";
		#phy-cells = <0>;
		max-bitrate = <5000000>;
		pinctrl-names = "default";
		pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
		standby-gpios = <&wkup_gpio0 54 GPIO_ACTIVE_LOW>;
		enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>;
	};

	transceiver2: can-phy1 {
		compatible = "ti,tcan1042";
		#phy-cells = <0>;
		max-bitrate = <5000000>;
		pinctrl-names = "default";
		pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
	};

	transceiver3: can-phy2 {
		compatible = "ti,tcan1043";
		#phy-cells = <0>;
		max-bitrate = <5000000>;
		standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>;
		enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
	};

	transceiver4: can-phy3 {
		compatible = "ti,tcan1042";
		#phy-cells = <0>;
		max-bitrate = <5000000>;
		pinctrl-names = "default";
		pinctrl-0 = <&main_mcan2_gpio_pins_default>;
		standby-gpios = <&main_gpio0 127 GPIO_ACTIVE_HIGH>;
	};

	dp_pwr_3v3: regulator-dp-pwr {
		compatible = "regulator-fixed";
		regulator-name = "dp-pwr";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		gpio = <&exp4 0 GPIO_ACTIVE_HIGH>; /* P0 - DP0_PWR_SW_EN */
		enable-active-high;
	};

	dp0: connector {
		compatible = "dp-connector";
		label = "DP0";
		type = "full-size";
		dp-pwr-supply = <&dp_pwr_3v3>;

		port {
			dp_connector_in: endpoint {
				remote-endpoint = <&dp0_out>;
			};
		};
	};
};

&main_pmx0 {
	sw10_button_pins_default: sw10-button-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
		>;
	};

	main_mmc1_pins_default: main-mmc1-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
			J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
			J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
			J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
			J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
			J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
			J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
			J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */
		>;
	};

	vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x1d8, PIN_INPUT, 7) /* (W4) SPI1_CS1.GPIO0_117 */
		>;
	};

	main_usbss0_pins_default: main-usbss0-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
		>;
	};

	main_usbss1_pins_default: main-usbss1-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
		>;
	};

	dp0_pins_default: dp0-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */
		>;
	};

	main_i2c1_exp4_pins_default: main-i2c1-exp4-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
		>;
	};

	main_i2c0_pins_default: main-i2c0-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
			J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
		>;
	};

	main_i2c1_pins_default: main-i2c1-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
			J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
		>;
	};

	main_i2c3_pins_default: main-i2c3-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
			J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
		>;
	};

	main_i2c6_pins_default: main-i2c6-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */
			J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */
		>;
	};

	mcasp10_pins_default: mcasp10-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
			J721E_IOPAD(0x160, PIN_OUTPUT_PULLDOWN, 12) /* (V28) RGMII5_TD3.MCASP10_AXR0 */
			J721E_IOPAD(0x164, PIN_OUTPUT_PULLDOWN, 12) /* (V29) RGMII5_TD2.MCASP10_AXR1 */
			J721E_IOPAD(0x170, PIN_OUTPUT_PULLDOWN, 12) /* (U29) RGMII5_TXC.MCASP10_AXR2 */
			J721E_IOPAD(0x174, PIN_OUTPUT_PULLDOWN, 12) /* (U25) RGMII5_RXC.MCASP10_AXR3 */
			J721E_IOPAD(0x198, PIN_INPUT_PULLDOWN, 12) /* (V25) RGMII6_TD1.MCASP10_AXR4 */
			J721E_IOPAD(0x19c, PIN_INPUT_PULLDOWN, 12) /* (W27) RGMII6_TD0.MCASP10_AXR5 */
			J721E_IOPAD(0x1a0, PIN_INPUT_PULLDOWN, 12) /* (W29) RGMII6_TXC.MCASP10_AXR6 */
		>;
	};

	audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
		>;
	};

	main_mcan0_pins_default: main-mcan0-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x208, PIN_INPUT, 0) /* (W5) MCAN0_RX */
			J721E_IOPAD(0x20c, PIN_OUTPUT, 0) /* (W6) MCAN0_TX */
		>;
	};

	main_mcan2_pins_default: main-mcan2-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x01f0, PIN_INPUT, 3) /* (AC2) MCAN2_RX.GPIO0_123 */
			J721E_IOPAD(0x01f4, PIN_OUTPUT, 3) /* (AB1) MCAN2_TX.GPIO0_124 */
		>;
	};

	main_mcan2_gpio_pins_default: main-mcan2-gpio-pins-default {
		pinctrl-single,pins = <
			J721E_IOPAD(0x200, PIN_INPUT, 7) /* (AC4) UART1_CTSn.GPIO0_127 */
		>;
	};
};

&wkup_pmx0 {
	sw11_button_pins_default: sw11-button-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
		>;
	};

	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */
			J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (C22) MCU_OSPI1_CSn0 */
			J721E_WKUP_IOPAD(0x40, PIN_INPUT, 0) /* (D22) MCU_OSPI1_D0 */
			J721E_WKUP_IOPAD(0x44, PIN_INPUT, 0) /* (G22) MCU_OSPI1_D1 */
			J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (D23) MCU_OSPI1_D2 */
			J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
			J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
			J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
		>;
	};

	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
			J721E_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
			J721E_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
			J721E_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
			J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
			J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
			J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
		>;
	};

	mcu_mdio_pins_default: mcu-mdio1-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
		>;
	};

	mcu_mcan0_pins_default: mcu-mcan0-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0xac, PIN_INPUT, 0) /* (C29) MCU_MCAN0_RX */
			J721E_WKUP_IOPAD(0xa8, PIN_OUTPUT, 0) /* (D29) MCU_MCAN0_TX */
		>;
	};

	mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 7) /* (F26) WKUP_GPIO0_0 */
			J721E_WKUP_IOPAD(0x98, PIN_INPUT, 7) /* (E28) MCU_SPI0_D1.WKUP_GPIO0_54 */
		>;
	};

	mcu_mcan1_pins_default: mcu-mcan1-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0xc4, PIN_INPUT, 0) /* (G24) WKUP_GPIO0_5.MCU_MCAN1_RX */
			J721E_WKUP_IOPAD(0xc0, PIN_OUTPUT, 0) /* (G25) WKUP_GPIO0_4.MCU_MCAN1_TX */
		>;
	};

	mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0xb8, PIN_INPUT, 7) /* (F28) WKUP_GPIO0_2 */
		>;
	};
};

&wkup_uart0 {
	/* Wakeup UART is used by System firmware */
	status = "reserved";
};

&mcu_uart0 {
	status = "okay";
	/* Default pinmux */
};

&main_uart0 {
	status = "okay";
	/* Shared with ATF on this platform */
	power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
};

&main_uart1 {
	status = "okay";
	/* Default pinmux */
};

&main_uart2 {
	status = "okay";
	/* Default pinmux */
};

&main_uart4 {
	status = "okay";
	/* Default pinmux */
};

&main_gpio2 {
	status = "disabled";
};

&main_gpio3 {
	status = "disabled";
};

&main_gpio4 {
	status = "disabled";
};

&main_gpio5 {
	status = "disabled";
};

&main_gpio6 {
	status = "disabled";
};

&main_gpio7 {
	status = "disabled";
};

&wkup_gpio1 {
	status = "disabled";
};

&main_sdhci0 {
	/* eMMC */
	non-removable;
	ti,driver-strength-ohm = <50>;
	disable-wp;
};

&main_sdhci1 {
	/* SD/MMC */
	vmmc-supply = <&vdd_mmc1>;
	vqmmc-supply = <&vdd_sd_dv_alt>;
	pinctrl-names = "default";
	pinctrl-0 = <&main_mmc1_pins_default>;
	ti,driver-strength-ohm = <50>;
	disable-wp;
};

&main_sdhci2 {
	/* Unused */
	status = "disabled";
};

&usb_serdes_mux {
	idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
};

&serdes_ln_ctrl {
	idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_PCIE0_LANE1>,
		      <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>,
		      <J721E_SERDES2_LANE0_PCIE2_LANE0>, <J721E_SERDES2_LANE1_PCIE2_LANE1>,
		      <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
		      <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
		      <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
};

&serdes_wiz3 {
	typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
	typec-dir-debounce-ms = <700>;	/* TUSB321, tCCB_DEFAULT 133 ms */
};

&serdes3 {
	serdes3_usb_link: phy@0 {
		reg = <0>;
		cdns,num-lanes = <2>;
		#phy-cells = <0>;
		cdns,phy-type = <PHY_TYPE_USB3>;
		resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>;
	};
};

&usbss0 {
	pinctrl-names = "default";
	pinctrl-0 = <&main_usbss0_pins_default>;
	ti,vbus-divider;
};

&usb0 {
	dr_mode = "otg";
	maximum-speed = "super-speed";
	phys = <&serdes3_usb_link>;
	phy-names = "cdns3,usb3-phy";
};

&usbss1 {
	pinctrl-names = "default";
	pinctrl-0 = <&main_usbss1_pins_default>;
	ti,usb2-only;
};

&usb1 {
	dr_mode = "host";
	maximum-speed = "high-speed";
};

&ospi1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0x0>;
		spi-tx-bus-width = <1>;
		spi-rx-bus-width = <4>;
		spi-max-frequency = <40000000>;
		cdns,tshsl-ns = <60>;
		cdns,tsd2d-ns = <60>;
		cdns,tchsh-ns = <60>;
		cdns,tslch-ns = <60>;
		cdns,read-delay = <2>;
	};
};

&tscadc0 {
	adc {
		ti,adc-channels = <0 1 2 3 4 5 6 7>;
	};
};

&tscadc1 {
	adc {
		ti,adc-channels = <0 1 2 3 4 5 6 7>;
	};
};

&main_i2c0 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&main_i2c0_pins_default>;
	clock-frequency = <400000>;

	exp1: gpio@20 {
		compatible = "ti,tca6416";
		reg = <0x20>;
		gpio-controller;
		#gpio-cells = <2>;
	};

	exp2: gpio@22 {
		compatible = "ti,tca6424";
		reg = <0x22>;
		gpio-controller;
		#gpio-cells = <2>;

		p09-hog {
			/* P11 - MCASP/TRACE_MUX_S0 */
			gpio-hog;
			gpios = <9 GPIO_ACTIVE_HIGH>;
			output-low;
			line-name = "MCASP/TRACE_MUX_S0";
		};

		p10-hog {
			/* P12 - MCASP/TRACE_MUX_S1 */
			gpio-hog;
			gpios = <10 GPIO_ACTIVE_HIGH>;
			output-high;
			line-name = "MCASP/TRACE_MUX_S1";
		};
	};
};

&main_i2c1 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&main_i2c1_pins_default>;
	clock-frequency = <400000>;

	exp4: gpio@20 {
		compatible = "ti,tca6408";
		reg = <0x20>;
		gpio-controller;
		#gpio-cells = <2>;
		pinctrl-names = "default";
		pinctrl-0 = <&main_i2c1_exp4_pins_default>;
		interrupt-parent = <&main_gpio1>;
		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
		interrupt-controller;
		#interrupt-cells = <2>;
	};
};

&k3_clks {
	/* Confiure AUDIO_EXT_REFCLK2 pin as output */
	pinctrl-names = "default";
	pinctrl-0 = <&audi_ext_refclk2_pins_default>;
};

&main_i2c3 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&main_i2c3_pins_default>;
	clock-frequency = <400000>;

	exp3: gpio@20 {
		compatible = "ti,tca6408";
		reg = <0x20>;
		gpio-controller;
		#gpio-cells = <2>;
	};

	pcm3168a_1: audio-codec@44 {
		compatible = "ti,pcm3168a";
		reg = <0x44>;

		#sound-dai-cells = <1>;

		reset-gpios = <&exp3 0 GPIO_ACTIVE_LOW>;

		/* C_AUDIO_REFCLK2 -> RGMII6_RXC (W26) */
		clocks = <&k3_clks 157 371>;
		clock-names = "scki";

		/* HSDIV3_16FFT_MAIN_4_HSDIVOUT2_CLK -> REFCLK2 */
		assigned-clocks = <&k3_clks 157 371>;
		assigned-clock-parents = <&k3_clks 157 400>;
		assigned-clock-rates = <24576000>; /* for 48KHz */

		VDD1-supply = <&vsys_3v3>;
		VDD2-supply = <&vsys_3v3>;
		VCCAD1-supply = <&vsys_5v0>;
		VCCAD2-supply = <&vsys_5v0>;
		VCCDA1-supply = <&vsys_5v0>;
		VCCDA2-supply = <&vsys_5v0>;
	};
};

&main_i2c6 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&main_i2c6_pins_default>;
	clock-frequency = <400000>;

	exp5: gpio@20 {
		compatible = "ti,tca6408";
		reg = <0x20>;
		gpio-controller;
		#gpio-cells = <2>;
	};
};

&mcu_cpsw {
	pinctrl-names = "default";
	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
};

&davinci_mdio {
	phy0: ethernet-phy@0 {
		reg = <0>;
		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
	};
};

&cpsw_port1 {
	phy-mode = "rgmii-rxid";
	phy-handle = <&phy0>;
};

&dss {
	/*
	 * These clock assignments are chosen to enable the following outputs:
	 *
	 * VP0 - DisplayPort SST
	 * VP1 - DPI0
	 * VP2 - DSI
	 * VP3 - DPI1
	 */

	assigned-clocks = <&k3_clks 152 1>,
			  <&k3_clks 152 4>,
			  <&k3_clks 152 9>,
			  <&k3_clks 152 13>;
	assigned-clock-parents = <&k3_clks 152 2>,	/* PLL16_HSDIV0 */
				 <&k3_clks 152 6>,	/* PLL19_HSDIV0 */
				 <&k3_clks 152 11>,	/* PLL18_HSDIV0 */
				 <&k3_clks 152 18>;	/* PLL23_HSDIV0 */
};

&dss_ports {
	port {
		dpi0_out: endpoint {
			remote-endpoint = <&dp0_in>;
		};
	};
};

&dp0_ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
		reg = <0>;
		dp0_in: endpoint {
			remote-endpoint = <&dpi0_out>;
		};
	};

	port@4 {
		reg = <4>;
		dp0_out: endpoint {
			remote-endpoint = <&dp_connector_in>;
		};
	};
};

&mcasp10 {
	status = "okay";
	#sound-dai-cells = <0>;

	pinctrl-names = "default";
	pinctrl-0 = <&mcasp10_pins_default>;

	op-mode = <0>;          /* MCASP_IIS_MODE */
	tdm-slots = <2>;
	auxclk-fs-ratio = <256>;

	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
		1 1 1 1
		2 2 2 0
	>;
	tx-num-evt = <0>;
	rx-num-evt = <0>;
};

&cmn_refclk1 {
	clock-frequency = <100000000>;
};

&wiz0_pll1_refclk {
	assigned-clocks = <&wiz0_pll1_refclk>;
	assigned-clock-parents = <&cmn_refclk1>;
};

&wiz0_refclk_dig {
	assigned-clocks = <&wiz0_refclk_dig>;
	assigned-clock-parents = <&cmn_refclk1>;
};

&wiz1_pll1_refclk {
	assigned-clocks = <&wiz1_pll1_refclk>;
	assigned-clock-parents = <&cmn_refclk1>;
};

&wiz1_refclk_dig {
	assigned-clocks = <&wiz1_refclk_dig>;
	assigned-clock-parents = <&cmn_refclk1>;
};

&wiz2_pll1_refclk {
	assigned-clocks = <&wiz2_pll1_refclk>;
	assigned-clock-parents = <&cmn_refclk1>;
};

&wiz2_refclk_dig {
	assigned-clocks = <&wiz2_refclk_dig>;
	assigned-clock-parents = <&cmn_refclk1>;
};

&serdes0 {
	assigned-clocks = <&serdes0 CDNS_SIERRA_PLL_CMNLC>;
	assigned-clock-parents = <&wiz0_pll1_refclk>;

	serdes0_pcie_link: phy@0 {
		reg = <0>;
		cdns,num-lanes = <1>;
		#phy-cells = <0>;
		cdns,phy-type = <PHY_TYPE_PCIE>;
		resets = <&serdes_wiz0 1>;
	};
};

&serdes1 {
	assigned-clocks = <&serdes1 CDNS_SIERRA_PLL_CMNLC>;
	assigned-clock-parents = <&wiz1_pll1_refclk>;

	serdes1_pcie_link: phy@0 {
		reg = <0>;
		cdns,num-lanes = <2>;
		#phy-cells = <0>;
		cdns,phy-type = <PHY_TYPE_PCIE>;
		resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>;
	};
};

&serdes2 {
	assigned-clocks = <&serdes2 CDNS_SIERRA_PLL_CMNLC>;
	assigned-clock-parents = <&wiz2_pll1_refclk>;

	serdes2_pcie_link: phy@0 {
		reg = <0>;
		cdns,num-lanes = <2>;
		#phy-cells = <0>;
		cdns,phy-type = <PHY_TYPE_PCIE>;
		resets = <&serdes_wiz2 1>, <&serdes_wiz2 2>;
	};
};

&serdes4 {
	torrent_phy_dp: phy@0 {
		reg = <0>;
		resets = <&serdes_wiz4 1>;
		cdns,phy-type = <PHY_TYPE_DP>;
		cdns,num-lanes = <4>;
		cdns,max-bit-rate = <5400>;
		#phy-cells = <0>;
	};
};

&mhdp {
	phys = <&torrent_phy_dp>;
	phy-names = "dpphy";
	pinctrl-names = "default";
	pinctrl-0 = <&dp0_pins_default>;
};

&pcie0_rc {
	reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
	phys = <&serdes0_pcie_link>;
	phy-names = "pcie-phy";
	num-lanes = <1>;
};

&pcie1_rc {
	reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
	phys = <&serdes1_pcie_link>;
	phy-names = "pcie-phy";
	num-lanes = <2>;
};

&pcie2_rc {
	reset-gpios = <&exp2 20 GPIO_ACTIVE_HIGH>;
	phys = <&serdes2_pcie_link>;
	phy-names = "pcie-phy";
	num-lanes = <2>;
};

&pcie0_ep {
	phys = <&serdes0_pcie_link>;
	phy-names = "pcie-phy";
	num-lanes = <1>;
	status = "disabled";
};

&pcie1_ep {
	phys = <&serdes1_pcie_link>;
	phy-names = "pcie-phy";
	num-lanes = <2>;
	status = "disabled";
};

&pcie2_ep {
	phys = <&serdes2_pcie_link>;
	phy-names = "pcie-phy";
	num-lanes = <2>;
	status = "disabled";
};

&pcie3_rc {
	status = "disabled";
};

&pcie3_ep {
	status = "disabled";
};

&icssg0_mdio {
	status = "disabled";
};

&icssg1_mdio {
	status = "disabled";
};

&mcu_mcan0 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&mcu_mcan0_pins_default>;
	phys = <&transceiver1>;
};

&mcu_mcan1 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&mcu_mcan1_pins_default>;
	phys = <&transceiver2>;
};

&main_mcan0 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&main_mcan0_pins_default>;
	phys = <&transceiver3>;
};

&main_mcan2 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&main_mcan2_pins_default>;
	phys = <&transceiver4>;
};