blob: 823c9cc98f18b26b9262dfd3d55938fb4c69570f [file] [log] [blame]
/*
* TI DA830/OMAP L137 EVM board
*
* Author: Mark A. Greer <mgreer@mvista.com>
* Derived from: arch/arm/mach-davinci/board-dm644x-evm.c
*
* 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/interrupt.h>
#include <linux/gpio.h>
#include <linux/gpio/machine.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/platform_data/pcf857x.h>
#include <linux/property.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/platform_data/gpio-davinci.h>
#include <linux/platform_data/mtd-davinci.h>
#include <linux/platform_data/mtd-davinci-aemif.h>
#include <linux/platform_data/spi-davinci.h>
#include <linux/platform_data/usb-davinci.h>
#include <linux/platform_data/ti-aemif.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/nvmem-provider.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
#include <mach/mux.h>
#include <mach/da8xx.h>
#include "irqs.h"
#define DA830_EVM_PHY_ID ""
/*
* USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
*/
#define ON_BD_USB_DRV GPIO_TO_PIN(1, 15)
#define ON_BD_USB_OVC GPIO_TO_PIN(2, 4)
static const short da830_evm_usb11_pins[] = {
DA830_GPIO1_15, DA830_GPIO2_4,
-1
};
static struct regulator_consumer_supply da830_evm_usb_supplies[] = {
REGULATOR_SUPPLY("vbus", NULL),
};
static struct regulator_init_data da830_evm_usb_vbus_data = {
.consumer_supplies = da830_evm_usb_supplies,
.num_consumer_supplies = ARRAY_SIZE(da830_evm_usb_supplies),
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
};
static struct fixed_voltage_config da830_evm_usb_vbus = {
.supply_name = "vbus",
.microvolts = 33000000,
.init_data = &da830_evm_usb_vbus_data,
};
static struct platform_device da830_evm_usb_vbus_device = {
.name = "reg-fixed-voltage",
.id = 0,
.dev = {
.platform_data = &da830_evm_usb_vbus,
},
};
static struct gpiod_lookup_table da830_evm_usb_oc_gpio_lookup = {
.dev_id = "ohci-da8xx",
.table = {
GPIO_LOOKUP("davinci_gpio", ON_BD_USB_OVC, "oc", 0),
{ }
},
};
static struct gpiod_lookup_table da830_evm_usb_vbus_gpio_lookup = {
.dev_id = "reg-fixed-voltage.0",
.table = {
GPIO_LOOKUP("davinci_gpio", ON_BD_USB_DRV, NULL, 0),
{ }
},
};
static struct gpiod_lookup_table *da830_evm_usb_gpio_lookups[] = {
&da830_evm_usb_oc_gpio_lookup,
&da830_evm_usb_vbus_gpio_lookup,
};
static struct da8xx_ohci_root_hub da830_evm_usb11_pdata = {
/* TPS2065 switch @ 5V */
.potpgt = (3 + 1) / 2, /* 3 ms max */
};
static __init void da830_evm_usb_init(void)
{
int ret;
ret = da8xx_register_usb_phy_clocks();
if (ret)
pr_warn("%s: USB PHY CLK registration failed: %d\n",
__func__, ret);
gpiod_add_lookup_tables(da830_evm_usb_gpio_lookups,
ARRAY_SIZE(da830_evm_usb_gpio_lookups));
ret = da8xx_register_usb_phy();
if (ret)
pr_warn("%s: USB PHY registration failed: %d\n",
__func__, ret);
ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
if (ret)
pr_warn("%s: USB 2.0 PinMux setup failed: %d\n", __func__, ret);
else {
/*
* TPS2065 switch @ 5V supplies 1 A (sustains 1.5 A),
* with the power on to power good time of 3 ms.
*/
ret = da8xx_register_usb20(1000, 3);
if (ret)
pr_warn("%s: USB 2.0 registration failed: %d\n",
__func__, ret);
}
ret = davinci_cfg_reg_list(da830_evm_usb11_pins);
if (ret) {
pr_warn("%s: USB 1.1 PinMux setup failed: %d\n", __func__, ret);
return;
}
ret = platform_device_register(&da830_evm_usb_vbus_device);
if (ret) {
pr_warn("%s: Unable to register the vbus supply\n", __func__);
return;
}
ret = da8xx_register_usb11(&da830_evm_usb11_pdata);
if (ret)
pr_warn("%s: USB 1.1 registration failed: %d\n", __func__, ret);
}
static const short da830_evm_mcasp1_pins[] = {
DA830_AHCLKX1, DA830_ACLKX1, DA830_AFSX1, DA830_AHCLKR1, DA830_AFSR1,
DA830_AMUTE1, DA830_AXR1_0, DA830_AXR1_1, DA830_AXR1_2, DA830_AXR1_5,
DA830_ACLKR1, DA830_AXR1_6, DA830_AXR1_7, DA830_AXR1_8, DA830_AXR1_10,
DA830_AXR1_11,
-1
};
static u8 da830_iis_serializer_direction[] = {
RX_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
INACTIVE_MODE, TX_MODE, INACTIVE_MODE, INACTIVE_MODE,
INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
};
static struct snd_platform_data da830_evm_snd_data = {
.tx_dma_offset = 0x2000,
.rx_dma_offset = 0x2000,
.op_mode = DAVINCI_MCASP_IIS_MODE,
.num_serializer = ARRAY_SIZE(da830_iis_serializer_direction),
.tdm_slots = 2,
.serial_dir = da830_iis_serializer_direction,
.asp_chan_q = EVENTQ_0,
.version = MCASP_VERSION_2,
.txnumevt = 1,
.rxnumevt = 1,
};
/*
* GPIO2[1] is used as MMC_SD_WP and GPIO2[2] as MMC_SD_INS.
*/
static const short da830_evm_mmc_sd_pins[] = {
DA830_MMCSD_DAT_0, DA830_MMCSD_DAT_1, DA830_MMCSD_DAT_2,
DA830_MMCSD_DAT_3, DA830_MMCSD_DAT_4, DA830_MMCSD_DAT_5,
DA830_MMCSD_DAT_6, DA830_MMCSD_DAT_7, DA830_MMCSD_CLK,
DA830_MMCSD_CMD, DA830_GPIO2_1, DA830_GPIO2_2,
-1
};
#define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1)
#define DA830_MMCSD_CD_PIN GPIO_TO_PIN(2, 2)
static struct gpiod_lookup_table mmc_gpios_table = {
.dev_id = "da830-mmc.0",
.table = {
/* gpio chip 1 contains gpio range 32-63 */
GPIO_LOOKUP("davinci_gpio", DA830_MMCSD_CD_PIN, "cd",
GPIO_ACTIVE_LOW),
GPIO_LOOKUP("davinci_gpio", DA830_MMCSD_WP_PIN, "wp",
GPIO_ACTIVE_LOW),
{ }
},
};
static struct davinci_mmc_config da830_evm_mmc_config = {
.wires = 8,
.max_freq = 50000000,
.caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
};
static inline void da830_evm_init_mmc(void)
{
int ret;
ret = davinci_cfg_reg_list(da830_evm_mmc_sd_pins);
if (ret) {
pr_warn("%s: mmc/sd mux setup failed: %d\n", __func__, ret);
return;
}
gpiod_add_lookup_table(&mmc_gpios_table);
ret = da8xx_register_mmcsd0(&da830_evm_mmc_config);
if (ret) {
pr_warn("%s: mmc/sd registration failed: %d\n", __func__, ret);
gpiod_remove_lookup_table(&mmc_gpios_table);
}
}
#define HAS_MMC IS_ENABLED(CONFIG_MMC_DAVINCI)
#ifdef CONFIG_DA830_UI_NAND
static struct mtd_partition da830_evm_nand_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
[0] = {
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
[1] = {
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* kernel */
[2] = {
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0,
},
/* file system */
[3] = {
.name = "filesystem",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0,
}
};
/* flash bbt descriptors */
static uint8_t da830_evm_nand_bbt_pattern[] = { 'B', 'b', 't', '0' };
static uint8_t da830_evm_nand_mirror_pattern[] = { '1', 't', 'b', 'B' };
static struct nand_bbt_descr da830_evm_nand_bbt_main_descr = {
.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
NAND_BBT_WRITE | NAND_BBT_2BIT |
NAND_BBT_VERSION | NAND_BBT_PERCHIP,
.offs = 2,
.len = 4,
.veroffs = 16,
.maxblocks = 4,
.pattern = da830_evm_nand_bbt_pattern
};
static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = {
.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
NAND_BBT_WRITE | NAND_BBT_2BIT |
NAND_BBT_VERSION | NAND_BBT_PERCHIP,
.offs = 2,
.len = 4,
.veroffs = 16,
.maxblocks = 4,
.pattern = da830_evm_nand_mirror_pattern
};
static struct davinci_aemif_timing da830_evm_nandflash_timing = {
.wsetup = 24,
.wstrobe = 21,
.whold = 14,
.rsetup = 19,
.rstrobe = 50,
.rhold = 0,
.ta = 20,
};
static struct davinci_nand_pdata da830_evm_nand_pdata = {
.core_chipsel = 1,
.parts = da830_evm_nand_partitions,
.nr_parts = ARRAY_SIZE(da830_evm_nand_partitions),
.engine_type = NAND_ECC_ENGINE_TYPE_ON_HOST,
.ecc_bits = 4,
.bbt_options = NAND_BBT_USE_FLASH,
.bbt_td = &da830_evm_nand_bbt_main_descr,
.bbt_md = &da830_evm_nand_bbt_mirror_descr,
.timing = &da830_evm_nandflash_timing,
};
static struct resource da830_evm_nand_resources[] = {
[0] = { /* First memory resource is NAND I/O window */
.start = DA8XX_AEMIF_CS3_BASE,
.end = DA8XX_AEMIF_CS3_BASE + PAGE_SIZE - 1,
.flags = IORESOURCE_MEM,
},
[1] = { /* Second memory resource is AEMIF control registers */
.start = DA8XX_AEMIF_CTL_BASE,
.end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device da830_evm_aemif_devices[] = {
{
.name = "davinci_nand",
.id = 1,
.dev = {
.platform_data = &da830_evm_nand_pdata,
},
.num_resources = ARRAY_SIZE(da830_evm_nand_resources),
.resource = da830_evm_nand_resources,
},
};
static struct resource da830_evm_aemif_resource[] = {
{
.start = DA8XX_AEMIF_CTL_BASE,
.end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct aemif_abus_data da830_evm_aemif_abus_data[] = {
{
.cs = 3,
},
};
static struct aemif_platform_data da830_evm_aemif_pdata = {
.abus_data = da830_evm_aemif_abus_data,
.num_abus_data = ARRAY_SIZE(da830_evm_aemif_abus_data),
.sub_devices = da830_evm_aemif_devices,
.num_sub_devices = ARRAY_SIZE(da830_evm_aemif_devices),
.cs_offset = 2,
};
static struct platform_device da830_evm_aemif_device = {
.name = "ti-aemif",
.id = -1,
.dev = {
.platform_data = &da830_evm_aemif_pdata,
},
.resource = da830_evm_aemif_resource,
.num_resources = ARRAY_SIZE(da830_evm_aemif_resource),
};
/*
* UI board NAND/NOR flashes only use 8-bit data bus.
*/
static const short da830_evm_emif25_pins[] = {
DA830_EMA_D_0, DA830_EMA_D_1, DA830_EMA_D_2, DA830_EMA_D_3,
DA830_EMA_D_4, DA830_EMA_D_5, DA830_EMA_D_6, DA830_EMA_D_7,
DA830_EMA_A_0, DA830_EMA_A_1, DA830_EMA_A_2, DA830_EMA_A_3,
DA830_EMA_A_4, DA830_EMA_A_5, DA830_EMA_A_6, DA830_EMA_A_7,
DA830_EMA_A_8, DA830_EMA_A_9, DA830_EMA_A_10, DA830_EMA_A_11,
DA830_EMA_A_12, DA830_EMA_BA_0, DA830_EMA_BA_1, DA830_NEMA_WE,
DA830_NEMA_CS_2, DA830_NEMA_CS_3, DA830_NEMA_OE, DA830_EMA_WAIT_0,
-1
};
static inline void da830_evm_init_nand(int mux_mode)
{
int ret;
if (HAS_MMC) {
pr_warn("WARNING: both MMC/SD and NAND are enabled, but they share AEMIF pins\n"
"\tDisable MMC/SD for NAND support\n");
return;
}
ret = davinci_cfg_reg_list(da830_evm_emif25_pins);
if (ret)
pr_warn("%s: emif25 mux setup failed: %d\n", __func__, ret);
ret = platform_device_register(&da830_evm_aemif_device);
if (ret)
pr_warn("%s: AEMIF device not registered\n", __func__);
gpio_direction_output(mux_mode, 1);
}
#else
static inline void da830_evm_init_nand(int mux_mode) { }
#endif
#ifdef CONFIG_DA830_UI_LCD
static inline void da830_evm_init_lcdc(int mux_mode)
{
int ret;
ret = davinci_cfg_reg_list(da830_lcdcntl_pins);
if (ret)
pr_warn("%s: lcdcntl mux setup failed: %d\n", __func__, ret);
ret = da8xx_register_lcdc(&sharp_lcd035q3dg01_pdata);
if (ret)
pr_warn("%s: lcd setup failed: %d\n", __func__, ret);
gpio_direction_output(mux_mode, 0);
}
#else
static inline void da830_evm_init_lcdc(int mux_mode) { }
#endif
static struct nvmem_cell_info da830_evm_nvmem_cells[] = {
{
.name = "macaddr",
.offset = 0x7f00,
.bytes = ETH_ALEN,
}
};
static struct nvmem_cell_table da830_evm_nvmem_cell_table = {
.nvmem_name = "1-00500",
.cells = da830_evm_nvmem_cells,
.ncells = ARRAY_SIZE(da830_evm_nvmem_cells),
};
static struct nvmem_cell_lookup da830_evm_nvmem_cell_lookup = {
.nvmem_name = "1-00500",
.cell_name = "macaddr",
.dev_id = "davinci_emac.1",
.con_id = "mac-address",
};
static const struct property_entry da830_evm_i2c_eeprom_properties[] = {
PROPERTY_ENTRY_U32("pagesize", 64),
{ }
};
static const struct software_node da830_evm_i2c_eeprom_node = {
.properties = da830_evm_i2c_eeprom_properties,
};
static int __init da830_evm_ui_expander_setup(struct i2c_client *client,
int gpio, unsigned ngpio, void *context)
{
gpio_request(gpio + 6, "UI MUX_MODE");
/* Drive mux mode low to match the default without UI card */
gpio_direction_output(gpio + 6, 0);
da830_evm_init_lcdc(gpio + 6);
da830_evm_init_nand(gpio + 6);
return 0;
}
static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
unsigned ngpio, void *context)
{
gpio_free(gpio + 6);
return 0;
}
static struct pcf857x_platform_data __initdata da830_evm_ui_expander_info = {
.gpio_base = DAVINCI_N_GPIO,
.setup = da830_evm_ui_expander_setup,
.teardown = da830_evm_ui_expander_teardown,
};
static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
{
I2C_BOARD_INFO("24c256", 0x50),
.swnode = &da830_evm_i2c_eeprom_node,
},
{
I2C_BOARD_INFO("tlv320aic3x", 0x18),
},
{
I2C_BOARD_INFO("pcf8574", 0x3f),
.platform_data = &da830_evm_ui_expander_info,
},
};
static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
.bus_freq = 100, /* kHz */
.bus_delay = 0, /* usec */
};
/*
* The following EDMA channels/slots are not being used by drivers (for
* example: Timer, GPIO, UART events etc) on da830/omap-l137 EVM, hence
* they are being reserved for codecs on the DSP side.
*/
static const s16 da830_dma_rsv_chans[][2] = {
/* (offset, number) */
{ 8, 2},
{12, 2},
{24, 4},
{30, 2},
{-1, -1}
};
static const s16 da830_dma_rsv_slots[][2] = {
/* (offset, number) */
{ 8, 2},
{12, 2},
{24, 4},
{30, 26},
{-1, -1}
};
static struct edma_rsv_info da830_edma_rsv[] = {
{
.rsv_chans = da830_dma_rsv_chans,
.rsv_slots = da830_dma_rsv_slots,
},
};
static struct mtd_partition da830evm_spiflash_part[] = {
[0] = {
.name = "DSP-UBL",
.offset = 0,
.size = SZ_8K,
.mask_flags = MTD_WRITEABLE,
},
[1] = {
.name = "ARM-UBL",
.offset = MTDPART_OFS_APPEND,
.size = SZ_16K + SZ_8K,
.mask_flags = MTD_WRITEABLE,
},
[2] = {
.name = "U-Boot",
.offset = MTDPART_OFS_APPEND,
.size = SZ_256K - SZ_32K,
.mask_flags = MTD_WRITEABLE,
},
[3] = {
.name = "U-Boot-Environment",
.offset = MTDPART_OFS_APPEND,
.size = SZ_16K,
.mask_flags = 0,
},
[4] = {
.name = "Kernel",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0,
},
};
static struct flash_platform_data da830evm_spiflash_data = {
.name = "m25p80",
.parts = da830evm_spiflash_part,
.nr_parts = ARRAY_SIZE(da830evm_spiflash_part),
.type = "w25x32",
};
static struct davinci_spi_config da830evm_spiflash_cfg = {
.io_type = SPI_IO_TYPE_DMA,
.c2tdelay = 8,
.t2cdelay = 8,
};
static struct spi_board_info da830evm_spi_info[] = {
{
.modalias = "m25p80",
.platform_data = &da830evm_spiflash_data,
.controller_data = &da830evm_spiflash_cfg,
.mode = SPI_MODE_0,
.max_speed_hz = 30000000,
.bus_num = 0,
.chip_select = 0,
},
};
static __init void da830_evm_init(void)
{
struct davinci_soc_info *soc_info = &davinci_soc_info;
int ret;
da830_register_clocks();
ret = da830_register_gpio();
if (ret)
pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
ret = da830_register_edma(da830_edma_rsv);
if (ret)
pr_warn("%s: edma registration failed: %d\n", __func__, ret);
ret = davinci_cfg_reg_list(da830_i2c0_pins);
if (ret)
pr_warn("%s: i2c0 mux setup failed: %d\n", __func__, ret);
ret = da8xx_register_i2c(0, &da830_evm_i2c_0_pdata);
if (ret)
pr_warn("%s: i2c0 registration failed: %d\n", __func__, ret);
da830_evm_usb_init();
soc_info->emac_pdata->rmii_en = 1;
soc_info->emac_pdata->phy_id = DA830_EVM_PHY_ID;
ret = davinci_cfg_reg_list(da830_cpgmac_pins);
if (ret)
pr_warn("%s: cpgmac mux setup failed: %d\n", __func__, ret);
ret = da8xx_register_emac();
if (ret)
pr_warn("%s: emac registration failed: %d\n", __func__, ret);
ret = da8xx_register_watchdog();
if (ret)
pr_warn("%s: watchdog registration failed: %d\n",
__func__, ret);
davinci_serial_init(da8xx_serial_device);
nvmem_add_cell_table(&da830_evm_nvmem_cell_table);
nvmem_add_cell_lookups(&da830_evm_nvmem_cell_lookup, 1);
i2c_register_board_info(1, da830_evm_i2c_devices,
ARRAY_SIZE(da830_evm_i2c_devices));
ret = davinci_cfg_reg_list(da830_evm_mcasp1_pins);
if (ret)
pr_warn("%s: mcasp1 mux setup failed: %d\n", __func__, ret);
da8xx_register_mcasp(1, &da830_evm_snd_data);
da830_evm_init_mmc();
ret = da8xx_register_rtc();
if (ret)
pr_warn("%s: rtc setup failed: %d\n", __func__, ret);
ret = spi_register_board_info(da830evm_spi_info,
ARRAY_SIZE(da830evm_spi_info));
if (ret)
pr_warn("%s: spi info registration failed: %d\n",
__func__, ret);
ret = da8xx_register_spi_bus(0, ARRAY_SIZE(da830evm_spi_info));
if (ret)
pr_warn("%s: spi 0 registration failed: %d\n", __func__, ret);
regulator_has_full_constraints();
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init da830_evm_console_init(void)
{
if (!machine_is_davinci_da830_evm())
return 0;
return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(da830_evm_console_init);
#endif
static void __init da830_evm_map_io(void)
{
da830_init();
}
MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
.atag_offset = 0x100,
.map_io = da830_evm_map_io,
.init_irq = da830_init_irq,
.init_time = da830_init_time,
.init_machine = da830_evm_init,
.init_late = davinci_init_late,
.dma_zone_size = SZ_128M,
MACHINE_END