diff --git a/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml b/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
index ff3a170..6d4cfd9 100644
--- a/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
+++ b/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
@@ -36,7 +36,11 @@
 
   vdd-supply:
     description:
-      VDD power supply to the hub
+      3V3 power supply to the hub
+
+  vdd2-supply:
+    description:
+      1V2 power supply to the hub
 
   peer-hub:
     $ref: /schemas/types.yaml#/definitions/phandle
@@ -62,6 +66,7 @@
       properties:
         reset-gpios: false
         vdd-supply: false
+        vdd2-supply: false
         peer-hub: false
         i2c-bus: false
     else:
diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
index e889158..915c820 100644
--- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
@@ -521,8 +521,8 @@
 
             interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
                          <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
-                         <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
-                         <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+                         <GIC_SPI 488 IRQ_TYPE_EDGE_BOTH>,
+                         <GIC_SPI 489 IRQ_TYPE_EDGE_BOTH>;
             interrupt-names = "hs_phy_irq", "ss_phy_irq",
                           "dm_hs_phy_irq", "dp_hs_phy_irq";
 
diff --git a/Documentation/devicetree/bindings/usb/usb-hcd.yaml b/Documentation/devicetree/bindings/usb/usb-hcd.yaml
index 692dd60..45a19d4 100644
--- a/Documentation/devicetree/bindings/usb/usb-hcd.yaml
+++ b/Documentation/devicetree/bindings/usb/usb-hcd.yaml
@@ -41,7 +41,7 @@
   - |
     usb {
         phys = <&usb2_phy1>, <&usb3_phy1>;
-        phy-names = "usb";
+        phy-names = "usb2", "usb3";
         #address-cells = <1>;
         #size-cells = <0>;
 
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 787354b..4cef568 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -87,7 +87,6 @@
 source "drivers/phy/mscc/Kconfig"
 source "drivers/phy/qualcomm/Kconfig"
 source "drivers/phy/ralink/Kconfig"
-source "drivers/phy/realtek/Kconfig"
 source "drivers/phy/renesas/Kconfig"
 source "drivers/phy/rockchip/Kconfig"
 source "drivers/phy/samsung/Kconfig"
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 868a220..fb3dc9d 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -26,7 +26,6 @@
 					   mscc/	\
 					   qualcomm/	\
 					   ralink/	\
-					   realtek/	\
 					   renesas/	\
 					   rockchip/	\
 					   samsung/	\
diff --git a/drivers/phy/realtek/Kconfig b/drivers/phy/realtek/Kconfig
deleted file mode 100644
index 75ac7e7..0000000
--- a/drivers/phy/realtek/Kconfig
+++ /dev/null
@@ -1,32 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-#
-# Phy drivers for Realtek platforms
-#
-
-if ARCH_REALTEK || COMPILE_TEST
-
-config PHY_RTK_RTD_USB2PHY
-	tristate "Realtek RTD USB2 PHY Transceiver Driver"
-	depends on USB_SUPPORT
-	select GENERIC_PHY
-	select USB_PHY
-	select USB_COMMON
-	help
-	  Enable this to support Realtek SoC USB2 phy transceiver.
-	  The DHC (digital home center) RTD series SoCs used the Synopsys
-	  DWC3 USB IP. This driver will do the PHY initialization
-	  of the parameters.
-
-config PHY_RTK_RTD_USB3PHY
-	tristate "Realtek RTD USB3 PHY Transceiver Driver"
-	depends on USB_SUPPORT
-	select GENERIC_PHY
-	select USB_PHY
-	select USB_COMMON
-	help
-	  Enable this to support Realtek SoC USB3 phy transceiver.
-	  The DHC (digital home center) RTD series SoCs used the Synopsys
-	  DWC3 USB IP. This driver will do the PHY initialization
-	  of the parameters.
-
-endif # ARCH_REALTEK || COMPILE_TEST
diff --git a/drivers/phy/realtek/Makefile b/drivers/phy/realtek/Makefile
deleted file mode 100644
index ed7b47f..0000000
--- a/drivers/phy/realtek/Makefile
+++ /dev/null
@@ -1,3 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_PHY_RTK_RTD_USB2PHY)	+= phy-rtk-usb2.o
-obj-$(CONFIG_PHY_RTK_RTD_USB3PHY)	+= phy-rtk-usb3.o
diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
deleted file mode 100644
index 0a64262..0000000
--- a/drivers/phy/realtek/phy-rtk-usb2.c
+++ /dev/null
@@ -1,1325 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- *  phy-rtk-usb2.c RTK usb2.0 PHY driver
- *
- * Copyright (C) 2023 Realtek Semiconductor Corporation
- *
- */
-
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/platform_device.h>
-#include <linux/uaccess.h>
-#include <linux/debugfs.h>
-#include <linux/nvmem-consumer.h>
-#include <linux/regmap.h>
-#include <linux/sys_soc.h>
-#include <linux/mfd/syscon.h>
-#include <linux/phy/phy.h>
-#include <linux/usb.h>
-#include <linux/usb/phy.h>
-#include <linux/usb/hcd.h>
-
-/* GUSB2PHYACCn register */
-#define PHY_NEW_REG_REQ BIT(25)
-#define PHY_VSTS_BUSY   BIT(23)
-#define PHY_VCTRL_SHIFT 8
-#define PHY_REG_DATA_MASK 0xff
-
-#define GET_LOW_NIBBLE(addr) ((addr) & 0x0f)
-#define GET_HIGH_NIBBLE(addr) (((addr) & 0xf0) >> 4)
-
-#define EFUS_USB_DC_CAL_RATE 2
-#define EFUS_USB_DC_CAL_MAX 7
-
-#define EFUS_USB_DC_DIS_RATE 1
-#define EFUS_USB_DC_DIS_MAX 7
-
-#define MAX_PHY_DATA_SIZE 20
-#define OFFEST_PHY_READ 0x20
-
-#define MAX_USB_PHY_NUM 4
-#define MAX_USB_PHY_PAGE0_DATA_SIZE 16
-#define MAX_USB_PHY_PAGE1_DATA_SIZE 16
-#define MAX_USB_PHY_PAGE2_DATA_SIZE 8
-
-#define SET_PAGE_OFFSET 0xf4
-#define SET_PAGE_0 0x9b
-#define SET_PAGE_1 0xbb
-#define SET_PAGE_2 0xdb
-
-#define PAGE_START 0xe0
-#define PAGE0_0XE4 0xe4
-#define PAGE0_0XE6 0xe6
-#define PAGE0_0XE7 0xe7
-#define PAGE1_0XE0 0xe0
-#define PAGE1_0XE2 0xe2
-
-#define SENSITIVITY_CTRL (BIT(4) | BIT(5) | BIT(6))
-#define ENABLE_AUTO_SENSITIVITY_CALIBRATION BIT(2)
-#define DEFAULT_DC_DRIVING_VALUE (0x8)
-#define DEFAULT_DC_DISCONNECTION_VALUE (0x6)
-#define HS_CLK_SELECT BIT(6)
-
-struct phy_reg {
-	void __iomem *reg_wrap_vstatus;
-	void __iomem *reg_gusb2phyacc0;
-	int vstatus_index;
-};
-
-struct phy_data {
-	u8 addr;
-	u8 data;
-};
-
-struct phy_cfg {
-	int page0_size;
-	struct phy_data page0[MAX_USB_PHY_PAGE0_DATA_SIZE];
-	int page1_size;
-	struct phy_data page1[MAX_USB_PHY_PAGE1_DATA_SIZE];
-	int page2_size;
-	struct phy_data page2[MAX_USB_PHY_PAGE2_DATA_SIZE];
-
-	int num_phy;
-
-	bool check_efuse;
-	int check_efuse_version;
-#define CHECK_EFUSE_V1 1
-#define CHECK_EFUSE_V2 2
-	int efuse_dc_driving_rate;
-	int efuse_dc_disconnect_rate;
-	int dc_driving_mask;
-	int dc_disconnect_mask;
-	bool usb_dc_disconnect_at_page0;
-	int driving_updated_for_dev_dis;
-
-	bool do_toggle;
-	bool do_toggle_driving;
-	bool use_default_parameter;
-	bool is_double_sensitivity_mode;
-};
-
-struct phy_parameter {
-	struct phy_reg phy_reg;
-
-	/* Get from efuse */
-	s8 efuse_usb_dc_cal;
-	s8 efuse_usb_dc_dis;
-
-	/* Get from dts */
-	bool inverse_hstx_sync_clock;
-	u32 driving_level;
-	s32 driving_level_compensate;
-	s32 disconnection_compensate;
-};
-
-struct rtk_phy {
-	struct usb_phy phy;
-	struct device *dev;
-
-	struct phy_cfg *phy_cfg;
-	int num_phy;
-	struct phy_parameter *phy_parameter;
-
-	struct dentry *debug_dir;
-};
-
-/* mapping 0xE0 to 0 ... 0xE7 to 7, 0xF0 to 8 ,,, 0xF7 to 15 */
-static inline int page_addr_to_array_index(u8 addr)
-{
-	return (int)((((addr) - PAGE_START) & 0x7) +
-		((((addr) - PAGE_START) & 0x10) >> 1));
-}
-
-static inline u8 array_index_to_page_addr(int index)
-{
-	return ((((index) + PAGE_START) & 0x7) +
-		((((index) & 0x8) << 1) + PAGE_START));
-}
-
-#define PHY_IO_TIMEOUT_USEC		(50000)
-#define PHY_IO_DELAY_US			(100)
-
-static inline int utmi_wait_register(void __iomem *reg, u32 mask, u32 result)
-{
-	int ret;
-	unsigned int val;
-
-	ret = read_poll_timeout(readl, val, ((val & mask) == result),
-				PHY_IO_DELAY_US, PHY_IO_TIMEOUT_USEC, false, reg);
-	if (ret) {
-		pr_err("%s can't program USB phy\n", __func__);
-		return -ETIMEDOUT;
-	}
-
-	return 0;
-}
-
-static char rtk_phy_read(struct phy_reg *phy_reg, char addr)
-{
-	void __iomem *reg_gusb2phyacc0 = phy_reg->reg_gusb2phyacc0;
-	unsigned int val;
-	int ret = 0;
-
-	addr -= OFFEST_PHY_READ;
-
-	/* polling until VBusy == 0 */
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
-	if (ret)
-		return (char)ret;
-
-	/* VCtrl = low nibble of addr, and set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
-	if (ret)
-		return (char)ret;
-
-	/* VCtrl = high nibble of addr, and set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
-	if (ret)
-		return (char)ret;
-
-	val = readl(reg_gusb2phyacc0);
-
-	return (char)(val & PHY_REG_DATA_MASK);
-}
-
-static int rtk_phy_write(struct phy_reg *phy_reg, char addr, char data)
-{
-	unsigned int val;
-	void __iomem *reg_wrap_vstatus = phy_reg->reg_wrap_vstatus;
-	void __iomem *reg_gusb2phyacc0 = phy_reg->reg_gusb2phyacc0;
-	int shift_bits = phy_reg->vstatus_index * 8;
-	int ret = 0;
-
-	/* write data to VStatusOut2 (data output to phy) */
-	writel((u32)data << shift_bits, reg_wrap_vstatus);
-
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
-	if (ret)
-		return ret;
-
-	/* VCtrl = low nibble of addr, set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
-
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
-	if (ret)
-		return ret;
-
-	/* VCtrl = high nibble of addr, set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
-
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
-	if (ret)
-		return ret;
-
-	return 0;
-}
-
-static int rtk_phy_set_page(struct phy_reg *phy_reg, int page)
-{
-	switch (page) {
-	case 0:
-		return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_0);
-	case 1:
-		return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_1);
-	case 2:
-		return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_2);
-	default:
-		pr_err("%s error page=%d\n", __func__, page);
-	}
-
-	return -EINVAL;
-}
-
-static u8 __updated_dc_disconnect_level_page0_0xe4(struct phy_cfg *phy_cfg,
-						   struct phy_parameter *phy_parameter, u8 data)
-{
-	u8 ret;
-	s32 val;
-	s32 dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
-	int offset = 4;
-
-	val = (s32)((data >> offset) & dc_disconnect_mask)
-		     + phy_parameter->efuse_usb_dc_dis
-		     + phy_parameter->disconnection_compensate;
-
-	if (val > dc_disconnect_mask)
-		val = dc_disconnect_mask;
-	else if (val < 0)
-		val = 0;
-
-	ret = (data & (~(dc_disconnect_mask << offset))) |
-		    (val & dc_disconnect_mask) << offset;
-
-	return ret;
-}
-
-/* updated disconnect level at page0 */
-static void update_dc_disconnect_level_at_page0(struct rtk_phy *rtk_phy,
-						struct phy_parameter *phy_parameter, bool update)
-{
-	struct phy_cfg *phy_cfg;
-	struct phy_reg *phy_reg;
-	struct phy_data *phy_data_page;
-	struct phy_data *phy_data;
-	u8 addr, data;
-	int offset = 4;
-	s32 dc_disconnect_mask;
-	int i;
-
-	phy_cfg = rtk_phy->phy_cfg;
-	phy_reg = &phy_parameter->phy_reg;
-
-	/* Set page 0 */
-	phy_data_page = phy_cfg->page0;
-	rtk_phy_set_page(phy_reg, 0);
-
-	i = page_addr_to_array_index(PAGE0_0XE4);
-	phy_data = phy_data_page + i;
-	if (!phy_data->addr) {
-		phy_data->addr = PAGE0_0XE4;
-		phy_data->data = rtk_phy_read(phy_reg, PAGE0_0XE4);
-	}
-
-	addr = phy_data->addr;
-	data = phy_data->data;
-	dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
-
-	if (update)
-		data = __updated_dc_disconnect_level_page0_0xe4(phy_cfg, phy_parameter, data);
-	else
-		data = (data & ~(dc_disconnect_mask << offset)) |
-			(DEFAULT_DC_DISCONNECTION_VALUE << offset);
-
-	if (rtk_phy_write(phy_reg, addr, data))
-		dev_err(rtk_phy->dev,
-			"%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
-			__func__, addr, data);
-}
-
-static u8 __updated_dc_disconnect_level_page1_0xe2(struct phy_cfg *phy_cfg,
-						   struct phy_parameter *phy_parameter, u8 data)
-{
-	u8 ret;
-	s32 val;
-	s32 dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
-
-	if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
-		val = (s32)(data & dc_disconnect_mask)
-			    + phy_parameter->efuse_usb_dc_dis
-			    + phy_parameter->disconnection_compensate;
-	} else { /* for CHECK_EFUSE_V2 or no efuse */
-		if (phy_parameter->efuse_usb_dc_dis)
-			val = (s32)(phy_parameter->efuse_usb_dc_dis +
-				    phy_parameter->disconnection_compensate);
-		else
-			val = (s32)((data & dc_disconnect_mask) +
-				    phy_parameter->disconnection_compensate);
-	}
-
-	if (val > dc_disconnect_mask)
-		val = dc_disconnect_mask;
-	else if (val < 0)
-		val = 0;
-
-	ret = (data & (~dc_disconnect_mask)) | (val & dc_disconnect_mask);
-
-	return ret;
-}
-
-/* updated disconnect level at page1 */
-static void update_dc_disconnect_level_at_page1(struct rtk_phy *rtk_phy,
-						struct phy_parameter *phy_parameter, bool update)
-{
-	struct phy_cfg *phy_cfg;
-	struct phy_data *phy_data_page;
-	struct phy_data *phy_data;
-	struct phy_reg *phy_reg;
-	u8 addr, data;
-	s32 dc_disconnect_mask;
-	int i;
-
-	phy_cfg = rtk_phy->phy_cfg;
-	phy_reg = &phy_parameter->phy_reg;
-
-	/* Set page 1 */
-	phy_data_page = phy_cfg->page1;
-	rtk_phy_set_page(phy_reg, 1);
-
-	i = page_addr_to_array_index(PAGE1_0XE2);
-	phy_data = phy_data_page + i;
-	if (!phy_data->addr) {
-		phy_data->addr = PAGE1_0XE2;
-		phy_data->data = rtk_phy_read(phy_reg, PAGE1_0XE2);
-	}
-
-	addr = phy_data->addr;
-	data = phy_data->data;
-	dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
-
-	if (update)
-		data = __updated_dc_disconnect_level_page1_0xe2(phy_cfg, phy_parameter, data);
-	else
-		data = (data & ~dc_disconnect_mask) | DEFAULT_DC_DISCONNECTION_VALUE;
-
-	if (rtk_phy_write(phy_reg, addr, data))
-		dev_err(rtk_phy->dev,
-			"%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
-			__func__, addr, data);
-}
-
-static void update_dc_disconnect_level(struct rtk_phy *rtk_phy,
-				       struct phy_parameter *phy_parameter, bool update)
-{
-	struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
-
-	if (phy_cfg->usb_dc_disconnect_at_page0)
-		update_dc_disconnect_level_at_page0(rtk_phy, phy_parameter, update);
-	else
-		update_dc_disconnect_level_at_page1(rtk_phy, phy_parameter, update);
-}
-
-static u8 __update_dc_driving_page0_0xe4(struct phy_cfg *phy_cfg,
-					 struct phy_parameter *phy_parameter, u8 data)
-{
-	s32 driving_level_compensate = phy_parameter->driving_level_compensate;
-	s32 dc_driving_mask = phy_cfg->dc_driving_mask;
-	s32 val;
-	u8 ret;
-
-	if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
-		val = (s32)(data & dc_driving_mask) + driving_level_compensate
-			    + phy_parameter->efuse_usb_dc_cal;
-	} else { /* for CHECK_EFUSE_V2 or no efuse */
-		if (phy_parameter->efuse_usb_dc_cal)
-			val = (s32)((phy_parameter->efuse_usb_dc_cal & dc_driving_mask)
-				    + driving_level_compensate);
-		else
-			val = (s32)(data & dc_driving_mask);
-	}
-
-	if (val > dc_driving_mask)
-		val = dc_driving_mask;
-	else if (val < 0)
-		val = 0;
-
-	ret = (data & (~dc_driving_mask)) | (val & dc_driving_mask);
-
-	return ret;
-}
-
-static void update_dc_driving_level(struct rtk_phy *rtk_phy,
-				    struct phy_parameter *phy_parameter)
-{
-	struct phy_cfg *phy_cfg;
-	struct phy_reg *phy_reg;
-
-	phy_reg = &phy_parameter->phy_reg;
-	phy_cfg = rtk_phy->phy_cfg;
-	if (!phy_cfg->page0[4].addr) {
-		rtk_phy_set_page(phy_reg, 0);
-		phy_cfg->page0[4].addr = PAGE0_0XE4;
-		phy_cfg->page0[4].data = rtk_phy_read(phy_reg, PAGE0_0XE4);
-	}
-
-	if (phy_parameter->driving_level != DEFAULT_DC_DRIVING_VALUE) {
-		u32 dc_driving_mask;
-		u8 driving_level;
-		u8 data;
-
-		data = phy_cfg->page0[4].data;
-		dc_driving_mask = phy_cfg->dc_driving_mask;
-		driving_level = data & dc_driving_mask;
-
-		dev_dbg(rtk_phy->dev, "%s driving_level=%d => dts driving_level=%d\n",
-			__func__, driving_level, phy_parameter->driving_level);
-
-		phy_cfg->page0[4].data = (data & (~dc_driving_mask)) |
-			    (phy_parameter->driving_level & dc_driving_mask);
-	}
-
-	phy_cfg->page0[4].data = __update_dc_driving_page0_0xe4(phy_cfg,
-								phy_parameter,
-								phy_cfg->page0[4].data);
-}
-
-static void update_hs_clk_select(struct rtk_phy *rtk_phy,
-				 struct phy_parameter *phy_parameter)
-{
-	struct phy_cfg *phy_cfg;
-	struct phy_reg *phy_reg;
-
-	phy_cfg = rtk_phy->phy_cfg;
-	phy_reg = &phy_parameter->phy_reg;
-
-	if (phy_parameter->inverse_hstx_sync_clock) {
-		if (!phy_cfg->page0[6].addr) {
-			rtk_phy_set_page(phy_reg, 0);
-			phy_cfg->page0[6].addr = PAGE0_0XE6;
-			phy_cfg->page0[6].data = rtk_phy_read(phy_reg, PAGE0_0XE6);
-		}
-
-		phy_cfg->page0[6].data = phy_cfg->page0[6].data | HS_CLK_SELECT;
-	}
-}
-
-static void do_rtk_phy_toggle(struct rtk_phy *rtk_phy,
-			      int index, bool connect)
-{
-	struct phy_parameter *phy_parameter;
-	struct phy_cfg *phy_cfg;
-	struct phy_reg *phy_reg;
-	struct phy_data *phy_data_page;
-	u8 addr, data;
-	int i;
-
-	phy_cfg = rtk_phy->phy_cfg;
-	phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-	phy_reg = &phy_parameter->phy_reg;
-
-	if (!phy_cfg->do_toggle)
-		goto out;
-
-	if (phy_cfg->is_double_sensitivity_mode)
-		goto do_toggle_driving;
-
-	/* Set page 0 */
-	rtk_phy_set_page(phy_reg, 0);
-
-	addr = PAGE0_0XE7;
-	data = rtk_phy_read(phy_reg, addr);
-
-	if (connect)
-		rtk_phy_write(phy_reg, addr, data & (~SENSITIVITY_CTRL));
-	else
-		rtk_phy_write(phy_reg, addr, data | (SENSITIVITY_CTRL));
-
-do_toggle_driving:
-
-	if (!phy_cfg->do_toggle_driving)
-		goto do_toggle;
-
-	/* Page 0 addr 0xE4 driving capability */
-
-	/* Set page 0 */
-	phy_data_page = phy_cfg->page0;
-	rtk_phy_set_page(phy_reg, 0);
-
-	i = page_addr_to_array_index(PAGE0_0XE4);
-	addr = phy_data_page[i].addr;
-	data = phy_data_page[i].data;
-
-	if (connect) {
-		rtk_phy_write(phy_reg, addr, data);
-	} else {
-		u8 value;
-		s32 tmp;
-		s32 driving_updated =
-			    phy_cfg->driving_updated_for_dev_dis;
-		s32 dc_driving_mask = phy_cfg->dc_driving_mask;
-
-		tmp = (s32)(data & dc_driving_mask) + driving_updated;
-
-		if (tmp > dc_driving_mask)
-			tmp = dc_driving_mask;
-		else if (tmp < 0)
-			tmp = 0;
-
-		value = (data & (~dc_driving_mask)) | (tmp & dc_driving_mask);
-
-		rtk_phy_write(phy_reg, addr, value);
-	}
-
-do_toggle:
-	/* restore dc disconnect level before toggle */
-	update_dc_disconnect_level(rtk_phy, phy_parameter, false);
-
-	/* Set page 1 */
-	rtk_phy_set_page(phy_reg, 1);
-
-	addr = PAGE1_0XE0;
-	data = rtk_phy_read(phy_reg, addr);
-
-	rtk_phy_write(phy_reg, addr, data &
-		      (~ENABLE_AUTO_SENSITIVITY_CALIBRATION));
-	mdelay(1);
-	rtk_phy_write(phy_reg, addr, data |
-		      (ENABLE_AUTO_SENSITIVITY_CALIBRATION));
-
-	/* update dc disconnect level after toggle */
-	update_dc_disconnect_level(rtk_phy, phy_parameter, true);
-
-out:
-	return;
-}
-
-static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index)
-{
-	struct phy_parameter *phy_parameter;
-	struct phy_cfg *phy_cfg;
-	struct phy_data *phy_data_page;
-	struct phy_reg *phy_reg;
-	int i;
-
-	phy_cfg = rtk_phy->phy_cfg;
-	phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-	phy_reg = &phy_parameter->phy_reg;
-
-	if (phy_cfg->use_default_parameter) {
-		dev_dbg(rtk_phy->dev, "%s phy#%d use default parameter\n",
-			__func__, index);
-		goto do_toggle;
-	}
-
-	/* Set page 0 */
-	phy_data_page = phy_cfg->page0;
-	rtk_phy_set_page(phy_reg, 0);
-
-	for (i = 0; i < phy_cfg->page0_size; i++) {
-		struct phy_data *phy_data = phy_data_page + i;
-		u8 addr = phy_data->addr;
-		u8 data = phy_data->data;
-
-		if (!addr)
-			continue;
-
-		if (rtk_phy_write(phy_reg, addr, data)) {
-			dev_err(rtk_phy->dev,
-				"%s: Error to set page0 parameter addr=0x%x value=0x%x\n",
-				__func__, addr, data);
-			return -EINVAL;
-		}
-	}
-
-	/* Set page 1 */
-	phy_data_page = phy_cfg->page1;
-	rtk_phy_set_page(phy_reg, 1);
-
-	for (i = 0; i < phy_cfg->page1_size; i++) {
-		struct phy_data *phy_data = phy_data_page + i;
-		u8 addr = phy_data->addr;
-		u8 data = phy_data->data;
-
-		if (!addr)
-			continue;
-
-		if (rtk_phy_write(phy_reg, addr, data)) {
-			dev_err(rtk_phy->dev,
-				"%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
-				__func__, addr, data);
-			return -EINVAL;
-		}
-	}
-
-	if (phy_cfg->page2_size == 0)
-		goto do_toggle;
-
-	/* Set page 2 */
-	phy_data_page = phy_cfg->page2;
-	rtk_phy_set_page(phy_reg, 2);
-
-	for (i = 0; i < phy_cfg->page2_size; i++) {
-		struct phy_data *phy_data = phy_data_page + i;
-		u8 addr = phy_data->addr;
-		u8 data = phy_data->data;
-
-		if (!addr)
-			continue;
-
-		if (rtk_phy_write(phy_reg, addr, data)) {
-			dev_err(rtk_phy->dev,
-				"%s: Error to set page2 parameter addr=0x%x value=0x%x\n",
-				__func__, addr, data);
-			return -EINVAL;
-		}
-	}
-
-do_toggle:
-	do_rtk_phy_toggle(rtk_phy, index, false);
-
-	return 0;
-}
-
-static int rtk_phy_init(struct phy *phy)
-{
-	struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
-	unsigned long phy_init_time = jiffies;
-	int i, ret = 0;
-
-	if (!rtk_phy)
-		return -EINVAL;
-
-	for (i = 0; i < rtk_phy->num_phy; i++)
-		ret = do_rtk_phy_init(rtk_phy, i);
-
-	dev_dbg(rtk_phy->dev, "Initialized RTK USB 2.0 PHY (take %dms)\n",
-		jiffies_to_msecs(jiffies - phy_init_time));
-	return ret;
-}
-
-static int rtk_phy_exit(struct phy *phy)
-{
-	return 0;
-}
-
-static const struct phy_ops ops = {
-	.init		= rtk_phy_init,
-	.exit		= rtk_phy_exit,
-	.owner		= THIS_MODULE,
-};
-
-static void rtk_phy_toggle(struct usb_phy *usb2_phy, bool connect, int port)
-{
-	int index = port;
-	struct rtk_phy *rtk_phy = NULL;
-
-	rtk_phy = dev_get_drvdata(usb2_phy->dev);
-
-	if (index > rtk_phy->num_phy) {
-		dev_err(rtk_phy->dev, "%s: The port=%d is not in usb phy (num_phy=%d)\n",
-			__func__, index, rtk_phy->num_phy);
-		return;
-	}
-
-	do_rtk_phy_toggle(rtk_phy, index, connect);
-}
-
-static int rtk_phy_notify_port_status(struct usb_phy *x, int port,
-				      u16 portstatus, u16 portchange)
-{
-	bool connect = false;
-
-	pr_debug("%s port=%d portstatus=0x%x portchange=0x%x\n",
-		 __func__, port, (int)portstatus, (int)portchange);
-	if (portstatus & USB_PORT_STAT_CONNECTION)
-		connect = true;
-
-	if (portchange & USB_PORT_STAT_C_CONNECTION)
-		rtk_phy_toggle(x, connect, port);
-
-	return 0;
-}
-
-#ifdef CONFIG_DEBUG_FS
-static struct dentry *create_phy_debug_root(void)
-{
-	struct dentry *phy_debug_root;
-
-	phy_debug_root = debugfs_lookup("phy", usb_debug_root);
-	if (!phy_debug_root)
-		phy_debug_root = debugfs_create_dir("phy", usb_debug_root);
-
-	return phy_debug_root;
-}
-
-static int rtk_usb2_parameter_show(struct seq_file *s, void *unused)
-{
-	struct rtk_phy *rtk_phy = s->private;
-	struct phy_cfg *phy_cfg;
-	int i, index;
-
-	phy_cfg = rtk_phy->phy_cfg;
-
-	seq_puts(s, "Property:\n");
-	seq_printf(s, "  check_efuse: %s\n",
-		   phy_cfg->check_efuse ? "Enable" : "Disable");
-	seq_printf(s, "  check_efuse_version: %d\n",
-		   phy_cfg->check_efuse_version);
-	seq_printf(s, "  efuse_dc_driving_rate: %d\n",
-		   phy_cfg->efuse_dc_driving_rate);
-	seq_printf(s, "  dc_driving_mask: 0x%x\n",
-		   phy_cfg->dc_driving_mask);
-	seq_printf(s, "  efuse_dc_disconnect_rate: %d\n",
-		   phy_cfg->efuse_dc_disconnect_rate);
-	seq_printf(s, "  dc_disconnect_mask: 0x%x\n",
-		   phy_cfg->dc_disconnect_mask);
-	seq_printf(s, "  usb_dc_disconnect_at_page0: %s\n",
-		   phy_cfg->usb_dc_disconnect_at_page0 ? "true" : "false");
-	seq_printf(s, "  do_toggle: %s\n",
-		   phy_cfg->do_toggle ? "Enable" : "Disable");
-	seq_printf(s, "  do_toggle_driving: %s\n",
-		   phy_cfg->do_toggle_driving ? "Enable" : "Disable");
-	seq_printf(s, "  driving_updated_for_dev_dis: 0x%x\n",
-		   phy_cfg->driving_updated_for_dev_dis);
-	seq_printf(s, "  use_default_parameter: %s\n",
-		   phy_cfg->use_default_parameter ? "Enable" : "Disable");
-	seq_printf(s, "  is_double_sensitivity_mode: %s\n",
-		   phy_cfg->is_double_sensitivity_mode ? "Enable" : "Disable");
-
-	for (index = 0; index < rtk_phy->num_phy; index++) {
-		struct phy_parameter *phy_parameter;
-		struct phy_reg *phy_reg;
-		struct phy_data *phy_data_page;
-
-		phy_parameter =  &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-		phy_reg = &phy_parameter->phy_reg;
-
-		seq_printf(s, "PHY %d:\n", index);
-
-		seq_puts(s, "Page 0:\n");
-		/* Set page 0 */
-		phy_data_page = phy_cfg->page0;
-		rtk_phy_set_page(phy_reg, 0);
-
-		for (i = 0; i < phy_cfg->page0_size; i++) {
-			struct phy_data *phy_data = phy_data_page + i;
-			u8 addr = array_index_to_page_addr(i);
-			u8 data = phy_data->data;
-			u8 value = rtk_phy_read(phy_reg, addr);
-
-			if (phy_data->addr)
-				seq_printf(s, "  Page 0: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
-					   addr, data, value);
-			else
-				seq_printf(s, "  Page 0: addr=0x%x data=none ==> read value=0x%02x\n",
-					   addr, value);
-		}
-
-		seq_puts(s, "Page 1:\n");
-		/* Set page 1 */
-		phy_data_page = phy_cfg->page1;
-		rtk_phy_set_page(phy_reg, 1);
-
-		for (i = 0; i < phy_cfg->page1_size; i++) {
-			struct phy_data *phy_data = phy_data_page + i;
-			u8 addr = array_index_to_page_addr(i);
-			u8 data = phy_data->data;
-			u8 value = rtk_phy_read(phy_reg, addr);
-
-			if (phy_data->addr)
-				seq_printf(s, "  Page 1: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
-					   addr, data, value);
-			else
-				seq_printf(s, "  Page 1: addr=0x%x data=none ==> read value=0x%02x\n",
-					   addr, value);
-		}
-
-		if (phy_cfg->page2_size == 0)
-			goto out;
-
-		seq_puts(s, "Page 2:\n");
-		/* Set page 2 */
-		phy_data_page = phy_cfg->page2;
-		rtk_phy_set_page(phy_reg, 2);
-
-		for (i = 0; i < phy_cfg->page2_size; i++) {
-			struct phy_data *phy_data = phy_data_page + i;
-			u8 addr = array_index_to_page_addr(i);
-			u8 data = phy_data->data;
-			u8 value = rtk_phy_read(phy_reg, addr);
-
-			if (phy_data->addr)
-				seq_printf(s, "  Page 2: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
-					   addr, data, value);
-			else
-				seq_printf(s, "  Page 2: addr=0x%x data=none ==> read value=0x%02x\n",
-					   addr, value);
-		}
-
-out:
-		seq_puts(s, "PHY Property:\n");
-		seq_printf(s, "  efuse_usb_dc_cal: %d\n",
-			   (int)phy_parameter->efuse_usb_dc_cal);
-		seq_printf(s, "  efuse_usb_dc_dis: %d\n",
-			   (int)phy_parameter->efuse_usb_dc_dis);
-		seq_printf(s, "  inverse_hstx_sync_clock: %s\n",
-			   phy_parameter->inverse_hstx_sync_clock ? "Enable" : "Disable");
-		seq_printf(s, "  driving_level: %d\n",
-			   phy_parameter->driving_level);
-		seq_printf(s, "  driving_level_compensate: %d\n",
-			   phy_parameter->driving_level_compensate);
-		seq_printf(s, "  disconnection_compensate: %d\n",
-			   phy_parameter->disconnection_compensate);
-	}
-
-	return 0;
-}
-DEFINE_SHOW_ATTRIBUTE(rtk_usb2_parameter);
-
-static inline void create_debug_files(struct rtk_phy *rtk_phy)
-{
-	struct dentry *phy_debug_root = NULL;
-
-	phy_debug_root = create_phy_debug_root();
-	if (!phy_debug_root)
-		return;
-
-	rtk_phy->debug_dir = debugfs_create_dir(dev_name(rtk_phy->dev),
-						phy_debug_root);
-
-	debugfs_create_file("parameter", 0444, rtk_phy->debug_dir, rtk_phy,
-			    &rtk_usb2_parameter_fops);
-
-	return;
-}
-
-static inline void remove_debug_files(struct rtk_phy *rtk_phy)
-{
-	debugfs_remove_recursive(rtk_phy->debug_dir);
-}
-#else
-static inline void create_debug_files(struct rtk_phy *rtk_phy) { }
-static inline void remove_debug_files(struct rtk_phy *rtk_phy) { }
-#endif /* CONFIG_DEBUG_FS */
-
-static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
-				 struct phy_parameter *phy_parameter, int index)
-{
-	struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
-	u8 value = 0;
-	struct nvmem_cell *cell;
-	struct soc_device_attribute rtk_soc_groot[] = {
-		    { .family = "Realtek Groot",},
-		    { /* empty */ } };
-
-	if (!phy_cfg->check_efuse)
-		goto out;
-
-	/* Read efuse for usb dc cal */
-	cell = nvmem_cell_get(rtk_phy->dev, "usb-dc-cal");
-	if (IS_ERR(cell)) {
-		dev_dbg(rtk_phy->dev, "%s no usb-dc-cal: %ld\n",
-			__func__, PTR_ERR(cell));
-	} else {
-		unsigned char *buf;
-		size_t buf_size;
-
-		buf = nvmem_cell_read(cell, &buf_size);
-		if (!IS_ERR(buf)) {
-			value = buf[0] & phy_cfg->dc_driving_mask;
-			kfree(buf);
-		}
-		nvmem_cell_put(cell);
-	}
-
-	if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
-		int rate = phy_cfg->efuse_dc_driving_rate;
-
-		if (value <= EFUS_USB_DC_CAL_MAX)
-			phy_parameter->efuse_usb_dc_cal = (int8_t)(value * rate);
-		else
-			phy_parameter->efuse_usb_dc_cal = -(int8_t)
-				    ((EFUS_USB_DC_CAL_MAX & value) * rate);
-
-		if (soc_device_match(rtk_soc_groot)) {
-			dev_dbg(rtk_phy->dev, "For groot IC we need a workaround to adjust efuse_usb_dc_cal\n");
-
-			/* We don't multiple dc_cal_rate=2 for positive dc cal compensate */
-			if (value <= EFUS_USB_DC_CAL_MAX)
-				phy_parameter->efuse_usb_dc_cal = (int8_t)(value);
-
-			/* We set max dc cal compensate is 0x8 if otp is 0x7 */
-			if (value == 0x7)
-				phy_parameter->efuse_usb_dc_cal = (int8_t)(value + 1);
-		}
-	} else { /* for CHECK_EFUSE_V2 */
-		phy_parameter->efuse_usb_dc_cal = value & phy_cfg->dc_driving_mask;
-	}
-
-	/* Read efuse for usb dc disconnect level */
-	value = 0;
-	cell = nvmem_cell_get(rtk_phy->dev, "usb-dc-dis");
-	if (IS_ERR(cell)) {
-		dev_dbg(rtk_phy->dev, "%s no usb-dc-dis: %ld\n",
-			__func__, PTR_ERR(cell));
-	} else {
-		unsigned char *buf;
-		size_t buf_size;
-
-		buf = nvmem_cell_read(cell, &buf_size);
-		if (!IS_ERR(buf)) {
-			value = buf[0] & phy_cfg->dc_disconnect_mask;
-			kfree(buf);
-		}
-		nvmem_cell_put(cell);
-	}
-
-	if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
-		int rate = phy_cfg->efuse_dc_disconnect_rate;
-
-		if (value <= EFUS_USB_DC_DIS_MAX)
-			phy_parameter->efuse_usb_dc_dis = (int8_t)(value * rate);
-		else
-			phy_parameter->efuse_usb_dc_dis = -(int8_t)
-				    ((EFUS_USB_DC_DIS_MAX & value) * rate);
-	} else { /* for CHECK_EFUSE_V2 */
-		phy_parameter->efuse_usb_dc_dis = value & phy_cfg->dc_disconnect_mask;
-	}
-
-out:
-	return 0;
-}
-
-static int parse_phy_data(struct rtk_phy *rtk_phy)
-{
-	struct device *dev = rtk_phy->dev;
-	struct device_node *np = dev->of_node;
-	struct phy_parameter *phy_parameter;
-	int ret = 0;
-	int index;
-
-	rtk_phy->phy_parameter = devm_kzalloc(dev, sizeof(struct phy_parameter) *
-						rtk_phy->num_phy, GFP_KERNEL);
-	if (!rtk_phy->phy_parameter)
-		return -ENOMEM;
-
-	for (index = 0; index < rtk_phy->num_phy; index++) {
-		phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-
-		phy_parameter->phy_reg.reg_wrap_vstatus = of_iomap(np, 0);
-		phy_parameter->phy_reg.reg_gusb2phyacc0 = of_iomap(np, 1) + index;
-		phy_parameter->phy_reg.vstatus_index = index;
-
-		if (of_property_read_bool(np, "realtek,inverse-hstx-sync-clock"))
-			phy_parameter->inverse_hstx_sync_clock = true;
-		else
-			phy_parameter->inverse_hstx_sync_clock = false;
-
-		if (of_property_read_u32_index(np, "realtek,driving-level",
-					       index, &phy_parameter->driving_level))
-			phy_parameter->driving_level = DEFAULT_DC_DRIVING_VALUE;
-
-		if (of_property_read_u32_index(np, "realtek,driving-level-compensate",
-					       index, &phy_parameter->driving_level_compensate))
-			phy_parameter->driving_level_compensate = 0;
-
-		if (of_property_read_u32_index(np, "realtek,disconnection-compensate",
-					       index, &phy_parameter->disconnection_compensate))
-			phy_parameter->disconnection_compensate = 0;
-
-		get_phy_data_by_efuse(rtk_phy, phy_parameter, index);
-
-		update_dc_driving_level(rtk_phy, phy_parameter);
-
-		update_hs_clk_select(rtk_phy, phy_parameter);
-	}
-
-	return ret;
-}
-
-static int rtk_usb2phy_probe(struct platform_device *pdev)
-{
-	struct rtk_phy *rtk_phy;
-	struct device *dev = &pdev->dev;
-	struct phy *generic_phy;
-	struct phy_provider *phy_provider;
-	const struct phy_cfg *phy_cfg;
-	int ret = 0;
-
-	phy_cfg = of_device_get_match_data(dev);
-	if (!phy_cfg) {
-		dev_err(dev, "phy config are not assigned!\n");
-		return -EINVAL;
-	}
-
-	rtk_phy = devm_kzalloc(dev, sizeof(*rtk_phy), GFP_KERNEL);
-	if (!rtk_phy)
-		return -ENOMEM;
-
-	rtk_phy->dev			= &pdev->dev;
-	rtk_phy->phy.dev		= rtk_phy->dev;
-	rtk_phy->phy.label		= "rtk-usb2phy";
-	rtk_phy->phy.notify_port_status = rtk_phy_notify_port_status;
-
-	rtk_phy->phy_cfg = devm_kzalloc(dev, sizeof(*phy_cfg), GFP_KERNEL);
-
-	memcpy(rtk_phy->phy_cfg, phy_cfg, sizeof(*phy_cfg));
-
-	rtk_phy->num_phy = phy_cfg->num_phy;
-
-	ret = parse_phy_data(rtk_phy);
-	if (ret)
-		goto err;
-
-	platform_set_drvdata(pdev, rtk_phy);
-
-	generic_phy = devm_phy_create(rtk_phy->dev, NULL, &ops);
-	if (IS_ERR(generic_phy))
-		return PTR_ERR(generic_phy);
-
-	phy_set_drvdata(generic_phy, rtk_phy);
-
-	phy_provider = devm_of_phy_provider_register(rtk_phy->dev,
-						     of_phy_simple_xlate);
-	if (IS_ERR(phy_provider))
-		return PTR_ERR(phy_provider);
-
-	ret = usb_add_phy_dev(&rtk_phy->phy);
-	if (ret)
-		goto err;
-
-	create_debug_files(rtk_phy);
-
-err:
-	return ret;
-}
-
-static void rtk_usb2phy_remove(struct platform_device *pdev)
-{
-	struct rtk_phy *rtk_phy = platform_get_drvdata(pdev);
-
-	remove_debug_files(rtk_phy);
-
-	usb_remove_phy(&rtk_phy->phy);
-}
-
-static const struct phy_cfg rtd1295_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [0] = {0xe0, 0x90},
-		   [3] = {0xe3, 0x3a},
-		   [4] = {0xe4, 0x68},
-		   [6] = {0xe6, 0x91},
-		  [13] = {0xf5, 0x81},
-		  [15] = {0xf7, 0x02}, },
-	.page1_size = 8,
-	.page1 = { /* default parameter */ },
-	.page2_size = 0,
-	.page2 = { /* no parameter */ },
-	.num_phy = 1,
-	.check_efuse = false,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = 1,
-	.dc_driving_mask = 0xf,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = true,
-	.do_toggle = true,
-	.do_toggle_driving = false,
-	.driving_updated_for_dev_dis = 0xf,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = false,
-};
-
-static const struct phy_cfg rtd1395_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [4] = {0xe4, 0xac},
-		  [13] = {0xf5, 0x00},
-		  [15] = {0xf7, 0x02}, },
-	.page1_size = 8,
-	.page1 = { /* default parameter */ },
-	.page2_size = 0,
-	.page2 = { /* no parameter */ },
-	.num_phy = 1,
-	.check_efuse = false,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = 1,
-	.dc_driving_mask = 0xf,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = true,
-	.do_toggle = true,
-	.do_toggle_driving = false,
-	.driving_updated_for_dev_dis = 0xf,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = false,
-};
-
-static const struct phy_cfg rtd1395_phy_cfg_2port = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [4] = {0xe4, 0xac},
-		  [13] = {0xf5, 0x00},
-		  [15] = {0xf7, 0x02}, },
-	.page1_size = 8,
-	.page1 = { /* default parameter */ },
-	.page2_size = 0,
-	.page2 = { /* no parameter */ },
-	.num_phy = 2,
-	.check_efuse = false,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = 1,
-	.dc_driving_mask = 0xf,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = true,
-	.do_toggle = true,
-	.do_toggle_driving = false,
-	.driving_updated_for_dev_dis = 0xf,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = false,
-};
-
-static const struct phy_cfg rtd1619_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [4] = {0xe4, 0x68}, },
-	.page1_size = 8,
-	.page1 = { /* default parameter */ },
-	.page2_size = 0,
-	.page2 = { /* no parameter */ },
-	.num_phy = 1,
-	.check_efuse = true,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = 1,
-	.dc_driving_mask = 0xf,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = true,
-	.do_toggle = true,
-	.do_toggle_driving = false,
-	.driving_updated_for_dev_dis = 0xf,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = false,
-};
-
-static const struct phy_cfg rtd1319_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [0] = {0xe0, 0x18},
-		   [4] = {0xe4, 0x6a},
-		   [7] = {0xe7, 0x71},
-		  [13] = {0xf5, 0x15},
-		  [15] = {0xf7, 0x32}, },
-	.page1_size = 8,
-	.page1 = { [3] = {0xe3, 0x44}, },
-	.page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
-	.page2 = { [0] = {0xe0, 0x01}, },
-	.num_phy = 1,
-	.check_efuse = true,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = 1,
-	.dc_driving_mask = 0xf,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = true,
-	.do_toggle = true,
-	.do_toggle_driving = true,
-	.driving_updated_for_dev_dis = 0xf,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = true,
-};
-
-static const struct phy_cfg rtd1312c_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [0] = {0xe0, 0x14},
-		   [4] = {0xe4, 0x67},
-		   [5] = {0xe5, 0x55}, },
-	.page1_size = 8,
-	.page1 = { [3] = {0xe3, 0x23},
-		   [6] = {0xe6, 0x58}, },
-	.page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
-	.page2 = { /* default parameter */ },
-	.num_phy = 1,
-	.check_efuse = true,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = 1,
-	.dc_driving_mask = 0xf,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = true,
-	.do_toggle = true,
-	.do_toggle_driving = true,
-	.driving_updated_for_dev_dis = 0xf,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = true,
-};
-
-static const struct phy_cfg rtd1619b_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [0] = {0xe0, 0xa3},
-		   [4] = {0xe4, 0x88},
-		   [5] = {0xe5, 0x4f},
-		   [6] = {0xe6, 0x02}, },
-	.page1_size = 8,
-	.page1 = { [3] = {0xe3, 0x64}, },
-	.page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
-	.page2 = { [7] = {0xe7, 0x45}, },
-	.num_phy = 1,
-	.check_efuse = true,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
-	.dc_driving_mask = 0x1f,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = false,
-	.do_toggle = true,
-	.do_toggle_driving = true,
-	.driving_updated_for_dev_dis = 0x8,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = true,
-};
-
-static const struct phy_cfg rtd1319d_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [0] = {0xe0, 0xa3},
-		   [4] = {0xe4, 0x8e},
-		   [5] = {0xe5, 0x4f},
-		   [6] = {0xe6, 0x02}, },
-	.page1_size = MAX_USB_PHY_PAGE1_DATA_SIZE,
-	.page1 = { [14] = {0xf5, 0x1}, },
-	.page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
-	.page2 = { [7] = {0xe7, 0x44}, },
-	.check_efuse = true,
-	.num_phy = 1,
-	.check_efuse_version = CHECK_EFUSE_V1,
-	.efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
-	.dc_driving_mask = 0x1f,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = false,
-	.do_toggle = true,
-	.do_toggle_driving = false,
-	.driving_updated_for_dev_dis = 0x8,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = true,
-};
-
-static const struct phy_cfg rtd1315e_phy_cfg = {
-	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
-	.page0 = { [0] = {0xe0, 0xa3},
-		   [4] = {0xe4, 0x8c},
-		   [5] = {0xe5, 0x4f},
-		   [6] = {0xe6, 0x02}, },
-	.page1_size = MAX_USB_PHY_PAGE1_DATA_SIZE,
-	.page1 = { [3] = {0xe3, 0x7f},
-		  [14] = {0xf5, 0x01}, },
-	.page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
-	.page2 = { [7] = {0xe7, 0x44}, },
-	.num_phy = 1,
-	.check_efuse = true,
-	.check_efuse_version = CHECK_EFUSE_V2,
-	.efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
-	.dc_driving_mask = 0x1f,
-	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
-	.dc_disconnect_mask = 0xf,
-	.usb_dc_disconnect_at_page0 = false,
-	.do_toggle = true,
-	.do_toggle_driving = false,
-	.driving_updated_for_dev_dis = 0x8,
-	.use_default_parameter = false,
-	.is_double_sensitivity_mode = true,
-};
-
-static const struct of_device_id usbphy_rtk_dt_match[] = {
-	{ .compatible = "realtek,rtd1295-usb2phy", .data = &rtd1295_phy_cfg },
-	{ .compatible = "realtek,rtd1312c-usb2phy", .data = &rtd1312c_phy_cfg },
-	{ .compatible = "realtek,rtd1315e-usb2phy", .data = &rtd1315e_phy_cfg },
-	{ .compatible = "realtek,rtd1319-usb2phy", .data = &rtd1319_phy_cfg },
-	{ .compatible = "realtek,rtd1319d-usb2phy", .data = &rtd1319d_phy_cfg },
-	{ .compatible = "realtek,rtd1395-usb2phy", .data = &rtd1395_phy_cfg },
-	{ .compatible = "realtek,rtd1395-usb2phy-2port", .data = &rtd1395_phy_cfg_2port },
-	{ .compatible = "realtek,rtd1619-usb2phy", .data = &rtd1619_phy_cfg },
-	{ .compatible = "realtek,rtd1619b-usb2phy", .data = &rtd1619b_phy_cfg },
-	{},
-};
-MODULE_DEVICE_TABLE(of, usbphy_rtk_dt_match);
-
-static struct platform_driver rtk_usb2phy_driver = {
-	.probe		= rtk_usb2phy_probe,
-	.remove_new	= rtk_usb2phy_remove,
-	.driver		= {
-		.name	= "rtk-usb2phy",
-		.of_match_table = usbphy_rtk_dt_match,
-	},
-};
-
-module_platform_driver(rtk_usb2phy_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform: rtk-usb2phy");
-MODULE_AUTHOR("Stanley Chang <stanley_chang@realtek.com>");
-MODULE_DESCRIPTION("Realtek usb 2.0 phy driver");
diff --git a/drivers/phy/realtek/phy-rtk-usb3.c b/drivers/phy/realtek/phy-rtk-usb3.c
deleted file mode 100644
index 67446a8..0000000
--- a/drivers/phy/realtek/phy-rtk-usb3.c
+++ /dev/null
@@ -1,761 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- *  phy-rtk-usb3.c RTK usb3.0 phy driver
- *
- * copyright (c) 2023 realtek semiconductor corporation
- *
- */
-
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/platform_device.h>
-#include <linux/uaccess.h>
-#include <linux/debugfs.h>
-#include <linux/nvmem-consumer.h>
-#include <linux/regmap.h>
-#include <linux/sys_soc.h>
-#include <linux/mfd/syscon.h>
-#include <linux/phy/phy.h>
-#include <linux/usb.h>
-#include <linux/usb/hcd.h>
-#include <linux/usb/phy.h>
-
-#define USB_MDIO_CTRL_PHY_BUSY BIT(7)
-#define USB_MDIO_CTRL_PHY_WRITE BIT(0)
-#define USB_MDIO_CTRL_PHY_ADDR_SHIFT 8
-#define USB_MDIO_CTRL_PHY_DATA_SHIFT 16
-
-#define MAX_USB_PHY_DATA_SIZE 0x30
-#define PHY_ADDR_0X09 0x09
-#define PHY_ADDR_0X0B 0x0b
-#define PHY_ADDR_0X0D 0x0d
-#define PHY_ADDR_0X10 0x10
-#define PHY_ADDR_0X1F 0x1f
-#define PHY_ADDR_0X20 0x20
-#define PHY_ADDR_0X21 0x21
-#define PHY_ADDR_0X30 0x30
-
-#define REG_0X09_FORCE_CALIBRATION BIT(9)
-#define REG_0X0B_RX_OFFSET_RANGE_MASK 0xc
-#define REG_0X0D_RX_DEBUG_TEST_EN BIT(6)
-#define REG_0X10_DEBUG_MODE_SETTING 0x3c0
-#define REG_0X10_DEBUG_MODE_SETTING_MASK 0x3f8
-#define REG_0X1F_RX_OFFSET_CODE_MASK 0x1e
-
-#define USB_U3_TX_LFPS_SWING_TRIM_SHIFT 4
-#define USB_U3_TX_LFPS_SWING_TRIM_MASK 0xf
-#define AMPLITUDE_CONTROL_COARSE_MASK 0xff
-#define AMPLITUDE_CONTROL_FINE_MASK 0xffff
-#define AMPLITUDE_CONTROL_COARSE_DEFAULT 0xff
-#define AMPLITUDE_CONTROL_FINE_DEFAULT 0xffff
-
-#define PHY_ADDR_MAP_ARRAY_INDEX(addr) (addr)
-#define ARRAY_INDEX_MAP_PHY_ADDR(index) (index)
-
-struct phy_reg {
-	void __iomem *reg_mdio_ctl;
-};
-
-struct phy_data {
-	u8 addr;
-	u16 data;
-};
-
-struct phy_cfg {
-	int param_size;
-	struct phy_data param[MAX_USB_PHY_DATA_SIZE];
-
-	bool check_efuse;
-	bool do_toggle;
-	bool do_toggle_once;
-	bool use_default_parameter;
-	bool check_rx_front_end_offset;
-};
-
-struct phy_parameter {
-	struct phy_reg phy_reg;
-
-	/* Get from efuse */
-	u8 efuse_usb_u3_tx_lfps_swing_trim;
-
-	/* Get from dts */
-	u32 amplitude_control_coarse;
-	u32 amplitude_control_fine;
-};
-
-struct rtk_phy {
-	struct usb_phy phy;
-	struct device *dev;
-
-	struct phy_cfg *phy_cfg;
-	int num_phy;
-	struct phy_parameter *phy_parameter;
-
-	struct dentry *debug_dir;
-};
-
-#define PHY_IO_TIMEOUT_USEC		(50000)
-#define PHY_IO_DELAY_US			(100)
-
-static inline int utmi_wait_register(void __iomem *reg, u32 mask, u32 result)
-{
-	int ret;
-	unsigned int val;
-
-	ret = read_poll_timeout(readl, val, ((val & mask) == result),
-				PHY_IO_DELAY_US, PHY_IO_TIMEOUT_USEC, false, reg);
-	if (ret) {
-		pr_err("%s can't program USB phy\n", __func__);
-		return -ETIMEDOUT;
-	}
-
-	return 0;
-}
-
-static int rtk_phy3_wait_vbusy(struct phy_reg *phy_reg)
-{
-	return utmi_wait_register(phy_reg->reg_mdio_ctl, USB_MDIO_CTRL_PHY_BUSY, 0);
-}
-
-static u16 rtk_phy_read(struct phy_reg *phy_reg, char addr)
-{
-	unsigned int tmp;
-	u32 value;
-
-	tmp = (addr << USB_MDIO_CTRL_PHY_ADDR_SHIFT);
-
-	writel(tmp, phy_reg->reg_mdio_ctl);
-
-	rtk_phy3_wait_vbusy(phy_reg);
-
-	value = readl(phy_reg->reg_mdio_ctl);
-	value = value >> USB_MDIO_CTRL_PHY_DATA_SHIFT;
-
-	return (u16)value;
-}
-
-static int rtk_phy_write(struct phy_reg *phy_reg, char addr, u16 data)
-{
-	unsigned int val;
-
-	val = USB_MDIO_CTRL_PHY_WRITE |
-		    (addr << USB_MDIO_CTRL_PHY_ADDR_SHIFT) |
-		    (data << USB_MDIO_CTRL_PHY_DATA_SHIFT);
-
-	writel(val, phy_reg->reg_mdio_ctl);
-
-	rtk_phy3_wait_vbusy(phy_reg);
-
-	return 0;
-}
-
-static void do_rtk_usb3_phy_toggle(struct rtk_phy *rtk_phy, int index, bool connect)
-{
-	struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
-	struct phy_reg *phy_reg;
-	struct phy_parameter *phy_parameter;
-	struct phy_data *phy_data;
-	u8 addr;
-	u16 data;
-	int i;
-
-	phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-	phy_reg = &phy_parameter->phy_reg;
-
-	if (!phy_cfg->do_toggle)
-		return;
-
-	i = PHY_ADDR_MAP_ARRAY_INDEX(PHY_ADDR_0X09);
-	phy_data = phy_cfg->param + i;
-	addr = phy_data->addr;
-	data = phy_data->data;
-
-	if (!addr && !data) {
-		addr = PHY_ADDR_0X09;
-		data = rtk_phy_read(phy_reg, addr);
-		phy_data->addr = addr;
-		phy_data->data = data;
-	}
-
-	rtk_phy_write(phy_reg, addr, data & (~REG_0X09_FORCE_CALIBRATION));
-	mdelay(1);
-	rtk_phy_write(phy_reg, addr, data | REG_0X09_FORCE_CALIBRATION);
-}
-
-static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index)
-{
-	struct phy_cfg *phy_cfg;
-	struct phy_reg *phy_reg;
-	struct phy_parameter *phy_parameter;
-	int i = 0;
-
-	phy_cfg = rtk_phy->phy_cfg;
-	phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-	phy_reg = &phy_parameter->phy_reg;
-
-	if (phy_cfg->use_default_parameter)
-		goto do_toggle;
-
-	for (i = 0; i < phy_cfg->param_size; i++) {
-		struct phy_data *phy_data = phy_cfg->param + i;
-		u8 addr = phy_data->addr;
-		u16 data = phy_data->data;
-
-		if (!addr && !data)
-			continue;
-
-		rtk_phy_write(phy_reg, addr, data);
-	}
-
-do_toggle:
-	if (phy_cfg->do_toggle_once)
-		phy_cfg->do_toggle = true;
-
-	do_rtk_usb3_phy_toggle(rtk_phy, index, false);
-
-	if (phy_cfg->do_toggle_once) {
-		u16 check_value = 0;
-		int count = 10;
-		u16 value_0x0d, value_0x10;
-
-		/* Enable Debug mode by set 0x0D and 0x10 */
-		value_0x0d = rtk_phy_read(phy_reg, PHY_ADDR_0X0D);
-		value_0x10 = rtk_phy_read(phy_reg, PHY_ADDR_0X10);
-
-		rtk_phy_write(phy_reg, PHY_ADDR_0X0D,
-			      value_0x0d | REG_0X0D_RX_DEBUG_TEST_EN);
-		rtk_phy_write(phy_reg, PHY_ADDR_0X10,
-			      (value_0x10 & ~REG_0X10_DEBUG_MODE_SETTING_MASK) |
-			      REG_0X10_DEBUG_MODE_SETTING);
-
-		check_value = rtk_phy_read(phy_reg, PHY_ADDR_0X30);
-
-		while (!(check_value & BIT(15))) {
-			check_value = rtk_phy_read(phy_reg, PHY_ADDR_0X30);
-			mdelay(1);
-			if (count-- < 0)
-				break;
-		}
-
-		if (!(check_value & BIT(15)))
-			dev_info(rtk_phy->dev, "toggle fail addr=0x%02x, data=0x%04x\n",
-				 PHY_ADDR_0X30, check_value);
-
-		/* Disable Debug mode by set 0x0D and 0x10 to default*/
-		rtk_phy_write(phy_reg, PHY_ADDR_0X0D, value_0x0d);
-		rtk_phy_write(phy_reg, PHY_ADDR_0X10, value_0x10);
-
-		phy_cfg->do_toggle = false;
-	}
-
-	if (phy_cfg->check_rx_front_end_offset) {
-		u16 rx_offset_code, rx_offset_range;
-		u16 code_mask = REG_0X1F_RX_OFFSET_CODE_MASK;
-		u16 range_mask = REG_0X0B_RX_OFFSET_RANGE_MASK;
-		bool do_update = false;
-
-		rx_offset_code = rtk_phy_read(phy_reg, PHY_ADDR_0X1F);
-		if (((rx_offset_code & code_mask) == 0x0) ||
-		    ((rx_offset_code & code_mask) == code_mask))
-			do_update = true;
-
-		rx_offset_range = rtk_phy_read(phy_reg, PHY_ADDR_0X0B);
-		if (((rx_offset_range & range_mask) == range_mask) && do_update) {
-			dev_warn(rtk_phy->dev, "Don't update rx_offset_range (rx_offset_code=0x%x, rx_offset_range=0x%x)\n",
-				 rx_offset_code, rx_offset_range);
-			do_update = false;
-		}
-
-		if (do_update) {
-			u16 tmp1, tmp2;
-
-			tmp1 = rx_offset_range & (~range_mask);
-			tmp2 = rx_offset_range & range_mask;
-			tmp2 += (1 << 2);
-			rx_offset_range = tmp1 | (tmp2 & range_mask);
-			rtk_phy_write(phy_reg, PHY_ADDR_0X0B, rx_offset_range);
-			goto do_toggle;
-		}
-	}
-
-	return 0;
-}
-
-static int rtk_phy_init(struct phy *phy)
-{
-	struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
-	int ret = 0;
-	int i;
-	unsigned long phy_init_time = jiffies;
-
-	for (i = 0; i < rtk_phy->num_phy; i++)
-		ret = do_rtk_phy_init(rtk_phy, i);
-
-	dev_dbg(rtk_phy->dev, "Initialized RTK USB 3.0 PHY (take %dms)\n",
-		jiffies_to_msecs(jiffies - phy_init_time));
-
-	return ret;
-}
-
-static int rtk_phy_exit(struct phy *phy)
-{
-	return 0;
-}
-
-static const struct phy_ops ops = {
-	.init		= rtk_phy_init,
-	.exit		= rtk_phy_exit,
-	.owner		= THIS_MODULE,
-};
-
-static void rtk_phy_toggle(struct usb_phy *usb3_phy, bool connect, int port)
-{
-	int index = port;
-	struct rtk_phy *rtk_phy = NULL;
-
-	rtk_phy = dev_get_drvdata(usb3_phy->dev);
-
-	if (index > rtk_phy->num_phy) {
-		dev_err(rtk_phy->dev, "%s: The port=%d is not in usb phy (num_phy=%d)\n",
-			__func__, index, rtk_phy->num_phy);
-		return;
-	}
-
-	do_rtk_usb3_phy_toggle(rtk_phy, index, connect);
-}
-
-static int rtk_phy_notify_port_status(struct usb_phy *x, int port,
-				      u16 portstatus, u16 portchange)
-{
-	bool connect = false;
-
-	pr_debug("%s port=%d portstatus=0x%x portchange=0x%x\n",
-		 __func__, port, (int)portstatus, (int)portchange);
-	if (portstatus & USB_PORT_STAT_CONNECTION)
-		connect = true;
-
-	if (portchange & USB_PORT_STAT_C_CONNECTION)
-		rtk_phy_toggle(x, connect, port);
-
-	return 0;
-}
-
-#ifdef CONFIG_DEBUG_FS
-static struct dentry *create_phy_debug_root(void)
-{
-	struct dentry *phy_debug_root;
-
-	phy_debug_root = debugfs_lookup("phy", usb_debug_root);
-	if (!phy_debug_root)
-		phy_debug_root = debugfs_create_dir("phy", usb_debug_root);
-
-	return phy_debug_root;
-}
-
-static int rtk_usb3_parameter_show(struct seq_file *s, void *unused)
-{
-	struct rtk_phy *rtk_phy = s->private;
-	struct phy_cfg *phy_cfg;
-	int i, index;
-
-	phy_cfg = rtk_phy->phy_cfg;
-
-	seq_puts(s, "Property:\n");
-	seq_printf(s, "  check_efuse: %s\n",
-		   phy_cfg->check_efuse ? "Enable" : "Disable");
-	seq_printf(s, "  do_toggle: %s\n",
-		   phy_cfg->do_toggle ? "Enable" : "Disable");
-	seq_printf(s, "  do_toggle_once: %s\n",
-		   phy_cfg->do_toggle_once ? "Enable" : "Disable");
-	seq_printf(s, "  use_default_parameter: %s\n",
-		   phy_cfg->use_default_parameter ? "Enable" : "Disable");
-
-	for (index = 0; index < rtk_phy->num_phy; index++) {
-		struct phy_reg *phy_reg;
-		struct phy_parameter *phy_parameter;
-
-		phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-		phy_reg = &phy_parameter->phy_reg;
-
-		seq_printf(s, "PHY %d:\n", index);
-
-		for (i = 0; i < phy_cfg->param_size; i++) {
-			struct phy_data *phy_data = phy_cfg->param + i;
-			u8 addr = ARRAY_INDEX_MAP_PHY_ADDR(i);
-			u16 data = phy_data->data;
-
-			if (!phy_data->addr && !data)
-				seq_printf(s, "  addr = 0x%02x, data = none   ==> read value = 0x%04x\n",
-					   addr, rtk_phy_read(phy_reg, addr));
-			else
-				seq_printf(s, "  addr = 0x%02x, data = 0x%04x ==> read value = 0x%04x\n",
-					   addr, data, rtk_phy_read(phy_reg, addr));
-		}
-
-		seq_puts(s, "PHY Property:\n");
-		seq_printf(s, "  efuse_usb_u3_tx_lfps_swing_trim: 0x%x\n",
-			   (int)phy_parameter->efuse_usb_u3_tx_lfps_swing_trim);
-		seq_printf(s, "  amplitude_control_coarse: 0x%x\n",
-			   (int)phy_parameter->amplitude_control_coarse);
-		seq_printf(s, "  amplitude_control_fine: 0x%x\n",
-			   (int)phy_parameter->amplitude_control_fine);
-	}
-
-	return 0;
-}
-DEFINE_SHOW_ATTRIBUTE(rtk_usb3_parameter);
-
-static inline void create_debug_files(struct rtk_phy *rtk_phy)
-{
-	struct dentry *phy_debug_root = NULL;
-
-	phy_debug_root = create_phy_debug_root();
-
-	if (!phy_debug_root)
-		return;
-
-	rtk_phy->debug_dir = debugfs_create_dir(dev_name(rtk_phy->dev), phy_debug_root);
-
-	debugfs_create_file("parameter", 0444, rtk_phy->debug_dir, rtk_phy,
-			    &rtk_usb3_parameter_fops);
-
-	return;
-}
-
-static inline void remove_debug_files(struct rtk_phy *rtk_phy)
-{
-	debugfs_remove_recursive(rtk_phy->debug_dir);
-}
-#else
-static inline void create_debug_files(struct rtk_phy *rtk_phy) { }
-static inline void remove_debug_files(struct rtk_phy *rtk_phy) { }
-#endif /* CONFIG_DEBUG_FS */
-
-static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
-				 struct phy_parameter *phy_parameter, int index)
-{
-	struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
-	u8 value = 0;
-	struct nvmem_cell *cell;
-
-	if (!phy_cfg->check_efuse)
-		goto out;
-
-	cell = nvmem_cell_get(rtk_phy->dev, "usb_u3_tx_lfps_swing_trim");
-	if (IS_ERR(cell)) {
-		dev_dbg(rtk_phy->dev, "%s no usb_u3_tx_lfps_swing_trim: %ld\n",
-			__func__, PTR_ERR(cell));
-	} else {
-		unsigned char *buf;
-		size_t buf_size;
-
-		buf = nvmem_cell_read(cell, &buf_size);
-		if (!IS_ERR(buf)) {
-			value = buf[0] & USB_U3_TX_LFPS_SWING_TRIM_MASK;
-			kfree(buf);
-		}
-		nvmem_cell_put(cell);
-	}
-
-	if (value > 0 && value < 0x8)
-		phy_parameter->efuse_usb_u3_tx_lfps_swing_trim = 0x8;
-	else
-		phy_parameter->efuse_usb_u3_tx_lfps_swing_trim = (u8)value;
-
-out:
-	return 0;
-}
-
-static void update_amplitude_control_value(struct rtk_phy *rtk_phy,
-					   struct phy_parameter *phy_parameter)
-{
-	struct phy_cfg *phy_cfg;
-	struct phy_reg *phy_reg;
-
-	phy_reg = &phy_parameter->phy_reg;
-	phy_cfg = rtk_phy->phy_cfg;
-
-	if (phy_parameter->amplitude_control_coarse != AMPLITUDE_CONTROL_COARSE_DEFAULT) {
-		u16 val_mask = AMPLITUDE_CONTROL_COARSE_MASK;
-		u16 data;
-
-		if (!phy_cfg->param[PHY_ADDR_0X20].addr && !phy_cfg->param[PHY_ADDR_0X20].data) {
-			phy_cfg->param[PHY_ADDR_0X20].addr = PHY_ADDR_0X20;
-			data = rtk_phy_read(phy_reg, PHY_ADDR_0X20);
-		} else {
-			data = phy_cfg->param[PHY_ADDR_0X20].data;
-		}
-
-		data &= (~val_mask);
-		data |= (phy_parameter->amplitude_control_coarse & val_mask);
-
-		phy_cfg->param[PHY_ADDR_0X20].data = data;
-	}
-
-	if (phy_parameter->efuse_usb_u3_tx_lfps_swing_trim) {
-		u8 efuse_val = phy_parameter->efuse_usb_u3_tx_lfps_swing_trim;
-		u16 val_mask = USB_U3_TX_LFPS_SWING_TRIM_MASK;
-		int val_shift = USB_U3_TX_LFPS_SWING_TRIM_SHIFT;
-		u16 data;
-
-		if (!phy_cfg->param[PHY_ADDR_0X20].addr && !phy_cfg->param[PHY_ADDR_0X20].data) {
-			phy_cfg->param[PHY_ADDR_0X20].addr = PHY_ADDR_0X20;
-			data = rtk_phy_read(phy_reg, PHY_ADDR_0X20);
-		} else {
-			data = phy_cfg->param[PHY_ADDR_0X20].data;
-		}
-
-		data &= ~(val_mask << val_shift);
-		data |= ((efuse_val & val_mask) << val_shift);
-
-		phy_cfg->param[PHY_ADDR_0X20].data = data;
-	}
-
-	if (phy_parameter->amplitude_control_fine != AMPLITUDE_CONTROL_FINE_DEFAULT) {
-		u16 val_mask = AMPLITUDE_CONTROL_FINE_MASK;
-
-		if (!phy_cfg->param[PHY_ADDR_0X21].addr && !phy_cfg->param[PHY_ADDR_0X21].data)
-			phy_cfg->param[PHY_ADDR_0X21].addr = PHY_ADDR_0X21;
-
-		phy_cfg->param[PHY_ADDR_0X21].data =
-			    phy_parameter->amplitude_control_fine & val_mask;
-	}
-}
-
-static int parse_phy_data(struct rtk_phy *rtk_phy)
-{
-	struct device *dev = rtk_phy->dev;
-	struct phy_parameter *phy_parameter;
-	int ret = 0;
-	int index;
-
-	rtk_phy->phy_parameter = devm_kzalloc(dev, sizeof(struct phy_parameter) *
-					      rtk_phy->num_phy, GFP_KERNEL);
-	if (!rtk_phy->phy_parameter)
-		return -ENOMEM;
-
-	for (index = 0; index < rtk_phy->num_phy; index++) {
-		phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
-
-		phy_parameter->phy_reg.reg_mdio_ctl = of_iomap(dev->of_node, 0) + index;
-
-		/* Amplitude control address 0x20 bit 0 to bit 7 */
-		if (of_property_read_u32(dev->of_node, "realtek,amplitude-control-coarse-tuning",
-					 &phy_parameter->amplitude_control_coarse))
-			phy_parameter->amplitude_control_coarse = AMPLITUDE_CONTROL_COARSE_DEFAULT;
-
-		/* Amplitude control address 0x21 bit 0 to bit 16 */
-		if (of_property_read_u32(dev->of_node, "realtek,amplitude-control-fine-tuning",
-					 &phy_parameter->amplitude_control_fine))
-			phy_parameter->amplitude_control_fine = AMPLITUDE_CONTROL_FINE_DEFAULT;
-
-		get_phy_data_by_efuse(rtk_phy, phy_parameter, index);
-
-		update_amplitude_control_value(rtk_phy, phy_parameter);
-	}
-
-	return ret;
-}
-
-static int rtk_usb3phy_probe(struct platform_device *pdev)
-{
-	struct rtk_phy *rtk_phy;
-	struct device *dev = &pdev->dev;
-	struct phy *generic_phy;
-	struct phy_provider *phy_provider;
-	const struct phy_cfg *phy_cfg;
-	int ret;
-
-	phy_cfg = of_device_get_match_data(dev);
-	if (!phy_cfg) {
-		dev_err(dev, "phy config are not assigned!\n");
-		return -EINVAL;
-	}
-
-	rtk_phy = devm_kzalloc(dev, sizeof(*rtk_phy), GFP_KERNEL);
-	if (!rtk_phy)
-		return -ENOMEM;
-
-	rtk_phy->dev			= &pdev->dev;
-	rtk_phy->phy.dev		= rtk_phy->dev;
-	rtk_phy->phy.label		= "rtk-usb3phy";
-	rtk_phy->phy.notify_port_status = rtk_phy_notify_port_status;
-
-	rtk_phy->phy_cfg = devm_kzalloc(dev, sizeof(*phy_cfg), GFP_KERNEL);
-
-	memcpy(rtk_phy->phy_cfg, phy_cfg, sizeof(*phy_cfg));
-
-	rtk_phy->num_phy = 1;
-
-	ret = parse_phy_data(rtk_phy);
-	if (ret)
-		goto err;
-
-	platform_set_drvdata(pdev, rtk_phy);
-
-	generic_phy = devm_phy_create(rtk_phy->dev, NULL, &ops);
-	if (IS_ERR(generic_phy))
-		return PTR_ERR(generic_phy);
-
-	phy_set_drvdata(generic_phy, rtk_phy);
-
-	phy_provider = devm_of_phy_provider_register(rtk_phy->dev, of_phy_simple_xlate);
-	if (IS_ERR(phy_provider))
-		return PTR_ERR(phy_provider);
-
-	ret = usb_add_phy_dev(&rtk_phy->phy);
-	if (ret)
-		goto err;
-
-	create_debug_files(rtk_phy);
-
-err:
-	return ret;
-}
-
-static void rtk_usb3phy_remove(struct platform_device *pdev)
-{
-	struct rtk_phy *rtk_phy = platform_get_drvdata(pdev);
-
-	remove_debug_files(rtk_phy);
-
-	usb_remove_phy(&rtk_phy->phy);
-}
-
-static const struct phy_cfg rtd1295_phy_cfg = {
-	.param_size = MAX_USB_PHY_DATA_SIZE,
-	.param = {  [0] = {0x01, 0x4008},  [1] = {0x01, 0xe046},
-		    [2] = {0x02, 0x6046},  [3] = {0x03, 0x2779},
-		    [4] = {0x04, 0x72f5},  [5] = {0x05, 0x2ad3},
-		    [6] = {0x06, 0x000e},  [7] = {0x07, 0x2e00},
-		    [8] = {0x08, 0x3591},  [9] = {0x09, 0x525c},
-		   [10] = {0x0a, 0xa600}, [11] = {0x0b, 0xa904},
-		   [12] = {0x0c, 0xc000}, [13] = {0x0d, 0xef1c},
-		   [14] = {0x0e, 0x2000}, [15] = {0x0f, 0x0000},
-		   [16] = {0x10, 0x000c}, [17] = {0x11, 0x4c00},
-		   [18] = {0x12, 0xfc00}, [19] = {0x13, 0x0c81},
-		   [20] = {0x14, 0xde01}, [21] = {0x15, 0x0000},
-		   [22] = {0x16, 0x0000}, [23] = {0x17, 0x0000},
-		   [24] = {0x18, 0x0000}, [25] = {0x19, 0x4004},
-		   [26] = {0x1a, 0x1260}, [27] = {0x1b, 0xff00},
-		   [28] = {0x1c, 0xcb00}, [29] = {0x1d, 0xa03f},
-		   [30] = {0x1e, 0xc2e0}, [31] = {0x1f, 0x2807},
-		   [32] = {0x20, 0x947a}, [33] = {0x21, 0x88aa},
-		   [34] = {0x22, 0x0057}, [35] = {0x23, 0xab66},
-		   [36] = {0x24, 0x0800}, [37] = {0x25, 0x0000},
-		   [38] = {0x26, 0x040a}, [39] = {0x27, 0x01d6},
-		   [40] = {0x28, 0xf8c2}, [41] = {0x29, 0x3080},
-		   [42] = {0x2a, 0x3082}, [43] = {0x2b, 0x2078},
-		   [44] = {0x2c, 0xffff}, [45] = {0x2d, 0xffff},
-		   [46] = {0x2e, 0x0000}, [47] = {0x2f, 0x0040}, },
-	.check_efuse = false,
-	.do_toggle = true,
-	.do_toggle_once = false,
-	.use_default_parameter = false,
-	.check_rx_front_end_offset = false,
-};
-
-static const struct phy_cfg rtd1619_phy_cfg = {
-	.param_size = MAX_USB_PHY_DATA_SIZE,
-	.param = {  [8] = {0x08, 0x3591},
-		   [38] = {0x26, 0x840b},
-		   [40] = {0x28, 0xf842}, },
-	.check_efuse = false,
-	.do_toggle = true,
-	.do_toggle_once = false,
-	.use_default_parameter = false,
-	.check_rx_front_end_offset = false,
-};
-
-static const struct phy_cfg rtd1319_phy_cfg = {
-	.param_size = MAX_USB_PHY_DATA_SIZE,
-	.param = {  [1] = {0x01, 0xac86},
-		    [6] = {0x06, 0x0003},
-		    [9] = {0x09, 0x924c},
-		   [10] = {0x0a, 0xa608},
-		   [11] = {0x0b, 0xb905},
-		   [14] = {0x0e, 0x2010},
-		   [32] = {0x20, 0x705a},
-		   [33] = {0x21, 0xf645},
-		   [34] = {0x22, 0x0013},
-		   [35] = {0x23, 0xcb66},
-		   [41] = {0x29, 0xff00}, },
-	.check_efuse = true,
-	.do_toggle = true,
-	.do_toggle_once = false,
-	.use_default_parameter = false,
-	.check_rx_front_end_offset = false,
-};
-
-static const struct phy_cfg rtd1619b_phy_cfg = {
-	.param_size = MAX_USB_PHY_DATA_SIZE,
-	.param = {  [1] = {0x01, 0xac8c},
-		    [6] = {0x06, 0x0017},
-		    [9] = {0x09, 0x724c},
-		   [10] = {0x0a, 0xb610},
-		   [11] = {0x0b, 0xb90d},
-		   [13] = {0x0d, 0xef2a},
-		   [15] = {0x0f, 0x9050},
-		   [16] = {0x10, 0x000c},
-		   [32] = {0x20, 0x70ff},
-		   [34] = {0x22, 0x0013},
-		   [35] = {0x23, 0xdb66},
-		   [38] = {0x26, 0x8609},
-		   [41] = {0x29, 0xff13},
-		   [42] = {0x2a, 0x3070}, },
-	.check_efuse = true,
-	.do_toggle = false,
-	.do_toggle_once = true,
-	.use_default_parameter = false,
-	.check_rx_front_end_offset = false,
-};
-
-static const  struct phy_cfg rtd1319d_phy_cfg = {
-	.param_size = MAX_USB_PHY_DATA_SIZE,
-	.param = {  [1] = {0x01, 0xac89},
-		    [4] = {0x04, 0xf2f5},
-		    [6] = {0x06, 0x0017},
-		    [9] = {0x09, 0x424c},
-		   [10] = {0x0a, 0x9610},
-		   [11] = {0x0b, 0x9901},
-		   [12] = {0x0c, 0xf000},
-		   [13] = {0x0d, 0xef2a},
-		   [14] = {0x0e, 0x1000},
-		   [15] = {0x0f, 0x9050},
-		   [32] = {0x20, 0x7077},
-		   [35] = {0x23, 0x0b62},
-		   [37] = {0x25, 0x10ec},
-		   [42] = {0x2a, 0x3070}, },
-	.check_efuse = true,
-	.do_toggle = false,
-	.do_toggle_once = true,
-	.use_default_parameter = false,
-	.check_rx_front_end_offset = true,
-};
-
-static const struct of_device_id usbphy_rtk_dt_match[] = {
-	{ .compatible = "realtek,rtd1295-usb3phy", .data = &rtd1295_phy_cfg },
-	{ .compatible = "realtek,rtd1319-usb3phy", .data = &rtd1319_phy_cfg },
-	{ .compatible = "realtek,rtd1319d-usb3phy", .data = &rtd1319d_phy_cfg },
-	{ .compatible = "realtek,rtd1619-usb3phy", .data = &rtd1619_phy_cfg },
-	{ .compatible = "realtek,rtd1619b-usb3phy", .data = &rtd1619b_phy_cfg },
-	{},
-};
-MODULE_DEVICE_TABLE(of, usbphy_rtk_dt_match);
-
-static struct platform_driver rtk_usb3phy_driver = {
-	.probe		= rtk_usb3phy_probe,
-	.remove_new	= rtk_usb3phy_remove,
-	.driver		= {
-		.name	= "rtk-usb3phy",
-		.of_match_table = usbphy_rtk_dt_match,
-	},
-};
-
-module_platform_driver(rtk_usb3phy_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform: rtk-usb3phy");
-MODULE_AUTHOR("Stanley Chang <stanley_chang@realtek.com>");
-MODULE_DESCRIPTION("Realtek usb 3.0 phy driver");
diff --git a/drivers/thunderbolt/switch.c b/drivers/thunderbolt/switch.c
index 1e15ffa..44e9b09 100644
--- a/drivers/thunderbolt/switch.c
+++ b/drivers/thunderbolt/switch.c
@@ -1143,7 +1143,7 @@ int tb_port_lane_bonding_enable(struct tb_port *port)
 	 * Only set bonding if the link was not already bonded. This
 	 * avoids the lane adapter to re-enter bonding state.
 	 */
-	if (width == TB_LINK_WIDTH_SINGLE) {
+	if (width == TB_LINK_WIDTH_SINGLE && !tb_is_upstream_port(port)) {
 		ret = tb_port_set_lane_bonding(port, true);
 		if (ret)
 			goto err_lane1;
@@ -2880,6 +2880,7 @@ static int tb_switch_lane_bonding_disable(struct tb_switch *sw)
 	return tb_port_wait_for_link_width(down, TB_LINK_WIDTH_SINGLE, 100);
 }
 
+/* Note updating sw->link_width done in tb_switch_update_link_attributes() */
 static int tb_switch_asym_enable(struct tb_switch *sw, enum tb_link_width width)
 {
 	struct tb_port *up, *down, *port;
@@ -2919,10 +2920,10 @@ static int tb_switch_asym_enable(struct tb_switch *sw, enum tb_link_width width)
 			return ret;
 	}
 
-	sw->link_width = width;
 	return 0;
 }
 
+/* Note updating sw->link_width done in tb_switch_update_link_attributes() */
 static int tb_switch_asym_disable(struct tb_switch *sw)
 {
 	struct tb_port *up, *down;
@@ -2957,7 +2958,6 @@ static int tb_switch_asym_disable(struct tb_switch *sw)
 			return ret;
 	}
 
-	sw->link_width = TB_LINK_WIDTH_DUAL;
 	return 0;
 }
 
diff --git a/drivers/thunderbolt/tb.c b/drivers/thunderbolt/tb.c
index 5acdeb7..fd49f86 100644
--- a/drivers/thunderbolt/tb.c
+++ b/drivers/thunderbolt/tb.c
@@ -213,7 +213,17 @@ static void tb_add_dp_resources(struct tb_switch *sw)
 		if (!tb_switch_query_dp_resource(sw, port))
 			continue;
 
-		list_add(&port->list, &tcm->dp_resources);
+		/*
+		 * If DP IN on device router exist, position it at the
+		 * beginning of the DP resources list, so that it is used
+		 * before DP IN of the host router. This way external GPU(s)
+		 * will be prioritized when pairing DP IN to a DP OUT.
+		 */
+		if (tb_route(sw))
+			list_add(&port->list, &tcm->dp_resources);
+		else
+			list_add_tail(&port->list, &tcm->dp_resources);
+
 		tb_port_dbg(port, "DP IN resource available\n");
 	}
 }
diff --git a/drivers/usb/cdns3/cdnsp-ring.c b/drivers/usb/cdns3/cdnsp-ring.c
index af98177..02f297f 100644
--- a/drivers/usb/cdns3/cdnsp-ring.c
+++ b/drivers/usb/cdns3/cdnsp-ring.c
@@ -1529,6 +1529,7 @@ irqreturn_t cdnsp_thread_irq_handler(int irq, void *data)
 	unsigned long flags;
 	int counter = 0;
 
+	local_bh_disable();
 	spin_lock_irqsave(&pdev->lock, flags);
 
 	if (pdev->cdnsp_state & (CDNSP_STATE_HALTED | CDNSP_STATE_DYING)) {
@@ -1541,6 +1542,7 @@ irqreturn_t cdnsp_thread_irq_handler(int irq, void *data)
 			cdnsp_died(pdev);
 
 		spin_unlock_irqrestore(&pdev->lock, flags);
+		local_bh_enable();
 		return IRQ_HANDLED;
 	}
 
@@ -1557,6 +1559,7 @@ irqreturn_t cdnsp_thread_irq_handler(int irq, void *data)
 	cdnsp_update_erst_dequeue(pdev, event_ring_deq, 1);
 
 	spin_unlock_irqrestore(&pdev->lock, flags);
+	local_bh_enable();
 
 	return IRQ_HANDLED;
 }
diff --git a/drivers/usb/core/config.c b/drivers/usb/core/config.c
index b19e38d..7f8d33f 100644
--- a/drivers/usb/core/config.c
+++ b/drivers/usb/core/config.c
@@ -1047,7 +1047,7 @@ int usb_get_bos_descriptor(struct usb_device *dev)
 
 		if (cap->bDescriptorType != USB_DT_DEVICE_CAPABILITY) {
 			dev_notice(ddev, "descriptor type invalid, skip\n");
-			continue;
+			goto skip_to_next_descriptor;
 		}
 
 		switch (cap_type) {
@@ -1078,6 +1078,7 @@ int usb_get_bos_descriptor(struct usb_device *dev)
 			break;
 		}
 
+skip_to_next_descriptor:
 		total_len -= length;
 		buffer += length;
 	}
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index b4584a0..87480a6 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -622,29 +622,6 @@ static int hub_ext_port_status(struct usb_hub *hub, int port1, int type,
 		ret = 0;
 	}
 	mutex_unlock(&hub->status_mutex);
-
-	/*
-	 * There is no need to lock status_mutex here, because status_mutex
-	 * protects hub->status, and the phy driver only checks the port
-	 * status without changing the status.
-	 */
-	if (!ret) {
-		struct usb_device *hdev = hub->hdev;
-
-		/*
-		 * Only roothub will be notified of port state changes,
-		 * since the USB PHY only cares about changes at the next
-		 * level.
-		 */
-		if (is_root_hub(hdev)) {
-			struct usb_hcd *hcd = bus_to_hcd(hdev->bus);
-
-			if (hcd->usb_phy)
-				usb_phy_notify_port_status(hcd->usb_phy,
-							   port1 - 1, *status, *change);
-		}
-	}
-
 	return ret;
 }
 
diff --git a/drivers/usb/dwc2/hcd_intr.c b/drivers/usb/dwc2/hcd_intr.c
index 0144ca8..5c7538d4 100644
--- a/drivers/usb/dwc2/hcd_intr.c
+++ b/drivers/usb/dwc2/hcd_intr.c
@@ -2015,15 +2015,17 @@ static void dwc2_hc_n_intr(struct dwc2_hsotg *hsotg, int chnum)
 {
 	struct dwc2_qtd *qtd;
 	struct dwc2_host_chan *chan;
-	u32 hcint, hcintmsk;
+	u32 hcint, hcintraw, hcintmsk;
 
 	chan = hsotg->hc_ptr_array[chnum];
 
-	hcint = dwc2_readl(hsotg, HCINT(chnum));
+	hcintraw = dwc2_readl(hsotg, HCINT(chnum));
 	hcintmsk = dwc2_readl(hsotg, HCINTMSK(chnum));
+	hcint = hcintraw & hcintmsk;
+	dwc2_writel(hsotg, hcint, HCINT(chnum));
+
 	if (!chan) {
 		dev_err(hsotg->dev, "## hc_ptr_array for channel is NULL ##\n");
-		dwc2_writel(hsotg, hcint, HCINT(chnum));
 		return;
 	}
 
@@ -2032,11 +2034,9 @@ static void dwc2_hc_n_intr(struct dwc2_hsotg *hsotg, int chnum)
 			 chnum);
 		dev_vdbg(hsotg->dev,
 			 "  hcint 0x%08x, hcintmsk 0x%08x, hcint&hcintmsk 0x%08x\n",
-			 hcint, hcintmsk, hcint & hcintmsk);
+			 hcintraw, hcintmsk, hcint);
 	}
 
-	dwc2_writel(hsotg, hcint, HCINT(chnum));
-
 	/*
 	 * If we got an interrupt after someone called
 	 * dwc2_hcd_endpoint_disable() we don't want to crash below
@@ -2046,8 +2046,7 @@ static void dwc2_hc_n_intr(struct dwc2_hsotg *hsotg, int chnum)
 		return;
 	}
 
-	chan->hcint = hcint;
-	hcint &= hcintmsk;
+	chan->hcint = hcintraw;
 
 	/*
 	 * If the channel was halted due to a dequeue, the qtd list might
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 0328c86..b101dbf8 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -2034,6 +2034,8 @@ static int dwc3_probe(struct platform_device *pdev)
 
 	pm_runtime_put(dev);
 
+	dma_set_max_seg_size(dev, UINT_MAX);
+
 	return 0;
 
 err_exit_debugfs:
diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c
index 039bf24..57ddd2e 100644
--- a/drivers/usb/dwc3/drd.c
+++ b/drivers/usb/dwc3/drd.c
@@ -505,6 +505,7 @@ static int dwc3_setup_role_switch(struct dwc3 *dwc)
 		dwc->role_switch_default_mode = USB_DR_MODE_PERIPHERAL;
 		mode = DWC3_GCTL_PRTCAP_DEVICE;
 	}
+	dwc3_set_mode(dwc, mode);
 
 	dwc3_role_switch.fwnode = dev_fwnode(dwc->dev);
 	dwc3_role_switch.set = dwc3_usb_role_switch_set;
@@ -526,7 +527,6 @@ static int dwc3_setup_role_switch(struct dwc3 *dwc)
 		}
 	}
 
-	dwc3_set_mode(dwc, mode);
 	return 0;
 }
 #else
diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
index 3de43df..fdf6d5d 100644
--- a/drivers/usb/dwc3/dwc3-qcom.c
+++ b/drivers/usb/dwc3/dwc3-qcom.c
@@ -546,10 +546,9 @@ static int dwc3_qcom_setup_irq(struct platform_device *pdev)
 				pdata ? pdata->hs_phy_irq_index : -1);
 	if (irq > 0) {
 		/* Keep wakeup interrupts disabled until suspend */
-		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT | IRQF_NO_AUTOEN,
 					"qcom_dwc3 HS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "hs_phy_irq failed: %d\n", ret);
@@ -561,10 +560,9 @@ static int dwc3_qcom_setup_irq(struct platform_device *pdev)
 	irq = dwc3_qcom_get_irq(pdev, "dp_hs_phy_irq",
 				pdata ? pdata->dp_hs_phy_irq_index : -1);
 	if (irq > 0) {
-		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT | IRQF_NO_AUTOEN,
 					"qcom_dwc3 DP_HS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "dp_hs_phy_irq failed: %d\n", ret);
@@ -576,10 +574,9 @@ static int dwc3_qcom_setup_irq(struct platform_device *pdev)
 	irq = dwc3_qcom_get_irq(pdev, "dm_hs_phy_irq",
 				pdata ? pdata->dm_hs_phy_irq_index : -1);
 	if (irq > 0) {
-		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT | IRQF_NO_AUTOEN,
 					"qcom_dwc3 DM_HS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "dm_hs_phy_irq failed: %d\n", ret);
@@ -591,10 +588,9 @@ static int dwc3_qcom_setup_irq(struct platform_device *pdev)
 	irq = dwc3_qcom_get_irq(pdev, "ss_phy_irq",
 				pdata ? pdata->ss_phy_irq_index : -1);
 	if (irq > 0) {
-		irq_set_status_flags(irq, IRQ_NOAUTOEN);
 		ret = devm_request_threaded_irq(qcom->dev, irq, NULL,
 					qcom_dwc3_resume_irq,
-					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+					IRQF_ONESHOT | IRQF_NO_AUTOEN,
 					"qcom_dwc3 SS", qcom);
 		if (ret) {
 			dev_err(qcom->dev, "ss_phy_irq failed: %d\n", ret);
@@ -758,6 +754,7 @@ static int dwc3_qcom_of_register_core(struct platform_device *pdev)
 	if (!qcom->dwc3) {
 		ret = -ENODEV;
 		dev_err(dev, "failed to get dwc3 platform device\n");
+		of_platform_depopulate(dev);
 	}
 
 node_put:
@@ -766,9 +763,9 @@ static int dwc3_qcom_of_register_core(struct platform_device *pdev)
 	return ret;
 }
 
-static struct platform_device *
-dwc3_qcom_create_urs_usb_platdev(struct device *dev)
+static struct platform_device *dwc3_qcom_create_urs_usb_platdev(struct device *dev)
 {
+	struct platform_device *urs_usb = NULL;
 	struct fwnode_handle *fwh;
 	struct acpi_device *adev;
 	char name[8];
@@ -788,9 +785,26 @@ dwc3_qcom_create_urs_usb_platdev(struct device *dev)
 
 	adev = to_acpi_device_node(fwh);
 	if (!adev)
-		return NULL;
+		goto err_put_handle;
 
-	return acpi_create_platform_device(adev, NULL);
+	urs_usb = acpi_create_platform_device(adev, NULL);
+	if (IS_ERR_OR_NULL(urs_usb))
+		goto err_put_handle;
+
+	return urs_usb;
+
+err_put_handle:
+	fwnode_handle_put(fwh);
+
+	return urs_usb;
+}
+
+static void dwc3_qcom_destroy_urs_usb_platdev(struct platform_device *urs_usb)
+{
+	struct fwnode_handle *fwh = urs_usb->dev.fwnode;
+
+	platform_device_unregister(urs_usb);
+	fwnode_handle_put(fwh);
 }
 
 static int dwc3_qcom_probe(struct platform_device *pdev)
@@ -874,13 +888,13 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	qcom->qscratch_base = devm_ioremap_resource(dev, parent_res);
 	if (IS_ERR(qcom->qscratch_base)) {
 		ret = PTR_ERR(qcom->qscratch_base);
-		goto clk_disable;
+		goto free_urs;
 	}
 
 	ret = dwc3_qcom_setup_irq(pdev);
 	if (ret) {
 		dev_err(dev, "failed to setup IRQs, err=%d\n", ret);
-		goto clk_disable;
+		goto free_urs;
 	}
 
 	/*
@@ -899,7 +913,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 
 	if (ret) {
 		dev_err(dev, "failed to register DWC3 Core, err=%d\n", ret);
-		goto depopulate;
+		goto free_urs;
 	}
 
 	ret = dwc3_qcom_interconnect_init(qcom);
@@ -931,10 +945,16 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 interconnect_exit:
 	dwc3_qcom_interconnect_exit(qcom);
 depopulate:
-	if (np)
+	if (np) {
 		of_platform_depopulate(&pdev->dev);
-	else
-		platform_device_put(pdev);
+	} else {
+		device_remove_software_node(&qcom->dwc3->dev);
+		platform_device_del(qcom->dwc3);
+	}
+	platform_device_put(qcom->dwc3);
+free_urs:
+	if (qcom->urs_usb)
+		dwc3_qcom_destroy_urs_usb_platdev(qcom->urs_usb);
 clk_disable:
 	for (i = qcom->num_clocks - 1; i >= 0; i--) {
 		clk_disable_unprepare(qcom->clks[i]);
@@ -953,11 +973,16 @@ static void dwc3_qcom_remove(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	int i;
 
-	device_remove_software_node(&qcom->dwc3->dev);
-	if (np)
+	if (np) {
 		of_platform_depopulate(&pdev->dev);
-	else
-		platform_device_put(pdev);
+	} else {
+		device_remove_software_node(&qcom->dwc3->dev);
+		platform_device_del(qcom->dwc3);
+	}
+	platform_device_put(qcom->dwc3);
+
+	if (qcom->urs_usb)
+		dwc3_qcom_destroy_urs_usb_platdev(qcom->urs_usb);
 
 	for (i = qcom->num_clocks - 1; i >= 0; i--) {
 		clk_disable_unprepare(qcom->clks[i]);
diff --git a/drivers/usb/dwc3/dwc3-rtk.c b/drivers/usb/dwc3/dwc3-rtk.c
index 590028e..3cd6b18 100644
--- a/drivers/usb/dwc3/dwc3-rtk.c
+++ b/drivers/usb/dwc3/dwc3-rtk.c
@@ -183,10 +183,13 @@ static enum usb_device_speed __get_dwc3_maximum_speed(struct device_node *np)
 
 	ret = of_property_read_string(dwc3_np, "maximum-speed", &maximum_speed);
 	if (ret < 0)
-		return USB_SPEED_UNKNOWN;
+		goto out;
 
 	ret = match_string(speed_names, ARRAY_SIZE(speed_names), maximum_speed);
 
+out:
+	of_node_put(dwc3_np);
+
 	return (ret < 0) ? USB_SPEED_UNKNOWN : ret;
 }
 
@@ -339,6 +342,9 @@ static int dwc3_rtk_probe_dwc3_core(struct dwc3_rtk *rtk)
 
 	switch_usb2_role(rtk, rtk->cur_role);
 
+	platform_device_put(dwc3_pdev);
+	of_node_put(dwc3_node);
+
 	return 0;
 
 err_pdev_put:
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 5b3cd45..61f3f8b 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -650,9 +650,8 @@ static int check_isoc_ss_overlap(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 
 		if (sch_ep->ep_type == ISOC_OUT_EP) {
 			for (j = 0; j < sch_ep->num_budget_microframes; j++) {
-				k = XHCI_MTK_BW_INDEX(base + j + CS_OFFSET);
-				/* use cs to indicate existence of in-ss @(base+j) */
-				if (tt->fs_bus_bw_in[k])
+				k = XHCI_MTK_BW_INDEX(base + j);
+				if (tt->in_ss_cnt[k])
 					return -ESCH_SS_OVERLAP;
 			}
 		} else if (sch_ep->ep_type == ISOC_IN_EP || sch_ep->ep_type == INT_IN_EP) {
@@ -769,6 +768,14 @@ static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
 				tt->fs_frame_bw[f] -= (u16)sch_ep->bw_budget_table[j];
 			}
 		}
+
+		if (sch_ep->ep_type == ISOC_IN_EP || sch_ep->ep_type == INT_IN_EP) {
+			k = XHCI_MTK_BW_INDEX(base);
+			if (used)
+				tt->in_ss_cnt[k]++;
+			else
+				tt->in_ss_cnt[k]--;
+		}
 	}
 
 	if (used)
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index 865b55e..39f7ae7 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -38,6 +38,7 @@
  * @fs_bus_bw_in: save bandwidth used by FS/LS IN eps in each uframes
  * @ls_bus_bw: save bandwidth used by LS eps in each uframes
  * @fs_frame_bw: save bandwidth used by FS/LS eps in each FS frames
+ * @in_ss_cnt: the count of Start-Split for IN eps
  * @ep_list: Endpoints using this TT
  */
 struct mu3h_sch_tt {
@@ -45,6 +46,7 @@ struct mu3h_sch_tt {
 	u16 fs_bus_bw_in[XHCI_MTK_MAX_ESIT];
 	u8 ls_bus_bw[XHCI_MTK_MAX_ESIT];
 	u16 fs_frame_bw[XHCI_MTK_FRAMES_CNT];
+	u8 in_ss_cnt[XHCI_MTK_MAX_ESIT];
 	struct list_head ep_list;
 };
 
diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
index b931613..732cdeb 100644
--- a/drivers/usb/host/xhci-plat.c
+++ b/drivers/usb/host/xhci-plat.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/usb/phy.h>
 #include <linux/slab.h>
@@ -148,7 +149,7 @@ int xhci_plat_probe(struct platform_device *pdev, struct device *sysdev, const s
 	int			ret;
 	int			irq;
 	struct xhci_plat_priv	*priv = NULL;
-
+	bool			of_match;
 
 	if (usb_disabled())
 		return -ENODEV;
@@ -253,16 +254,23 @@ int xhci_plat_probe(struct platform_device *pdev, struct device *sysdev, const s
 					 &xhci->imod_interval);
 	}
 
-	hcd->usb_phy = devm_usb_get_phy_by_phandle(sysdev, "usb-phy", 0);
-	if (IS_ERR(hcd->usb_phy)) {
-		ret = PTR_ERR(hcd->usb_phy);
-		if (ret == -EPROBE_DEFER)
-			goto disable_clk;
-		hcd->usb_phy = NULL;
-	} else {
-		ret = usb_phy_init(hcd->usb_phy);
-		if (ret)
-			goto disable_clk;
+	/*
+	 * Drivers such as dwc3 manages PHYs themself (and rely on driver name
+	 * matching for the xhci platform device).
+	 */
+	of_match = of_match_device(pdev->dev.driver->of_match_table, &pdev->dev);
+	if (of_match) {
+		hcd->usb_phy = devm_usb_get_phy_by_phandle(sysdev, "usb-phy", 0);
+		if (IS_ERR(hcd->usb_phy)) {
+			ret = PTR_ERR(hcd->usb_phy);
+			if (ret == -EPROBE_DEFER)
+				goto disable_clk;
+			hcd->usb_phy = NULL;
+		} else {
+			ret = usb_phy_init(hcd->usb_phy);
+			if (ret)
+				goto disable_clk;
+		}
 	}
 
 	hcd->tpl_support = of_usb_host_tpl_support(sysdev->of_node);
@@ -285,15 +293,17 @@ int xhci_plat_probe(struct platform_device *pdev, struct device *sysdev, const s
 			goto dealloc_usb2_hcd;
 		}
 
-		xhci->shared_hcd->usb_phy = devm_usb_get_phy_by_phandle(sysdev,
-			    "usb-phy", 1);
-		if (IS_ERR(xhci->shared_hcd->usb_phy)) {
-			xhci->shared_hcd->usb_phy = NULL;
-		} else {
-			ret = usb_phy_init(xhci->shared_hcd->usb_phy);
-			if (ret)
-				dev_err(sysdev, "%s init usb3phy fail (ret=%d)\n",
-					    __func__, ret);
+		if (of_match) {
+			xhci->shared_hcd->usb_phy = devm_usb_get_phy_by_phandle(sysdev,
+										"usb-phy", 1);
+			if (IS_ERR(xhci->shared_hcd->usb_phy)) {
+				xhci->shared_hcd->usb_phy = NULL;
+			} else {
+				ret = usb_phy_init(xhci->shared_hcd->usb_phy);
+				if (ret)
+					dev_err(sysdev, "%s init usb3phy fail (ret=%d)\n",
+						__func__, ret);
+			}
 		}
 
 		xhci->shared_hcd->tpl_support = hcd->tpl_support;
diff --git a/drivers/usb/misc/onboard_usb_hub.c b/drivers/usb/misc/onboard_usb_hub.c
index a341b2f..2b45404 100644
--- a/drivers/usb/misc/onboard_usb_hub.c
+++ b/drivers/usb/misc/onboard_usb_hub.c
@@ -432,6 +432,8 @@ static const struct usb_device_id onboard_hub_id_table[] = {
 	{ USB_DEVICE(VENDOR_ID_MICROCHIP, 0x2412) }, /* USB2412 USB 2.0 */
 	{ USB_DEVICE(VENDOR_ID_MICROCHIP, 0x2514) }, /* USB2514B USB 2.0 */
 	{ USB_DEVICE(VENDOR_ID_MICROCHIP, 0x2517) }, /* USB2517 USB 2.0 */
+	{ USB_DEVICE(VENDOR_ID_MICROCHIP, 0x2744) }, /* USB5744 USB 2.0 */
+	{ USB_DEVICE(VENDOR_ID_MICROCHIP, 0x5744) }, /* USB5744 USB 3.0 */
 	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x0411) }, /* RTS5411 USB 3.1 */
 	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x5411) }, /* RTS5411 USB 2.1 */
 	{ USB_DEVICE(VENDOR_ID_REALTEK, 0x0414) }, /* RTS5414 USB 3.2 */
diff --git a/drivers/usb/misc/onboard_usb_hub.h b/drivers/usb/misc/onboard_usb_hub.h
index c4e24a7..292110e 100644
--- a/drivers/usb/misc/onboard_usb_hub.h
+++ b/drivers/usb/misc/onboard_usb_hub.h
@@ -16,6 +16,11 @@ static const struct onboard_hub_pdata microchip_usb424_data = {
 	.num_supplies = 1,
 };
 
+static const struct onboard_hub_pdata microchip_usb5744_data = {
+	.reset_us = 0,
+	.num_supplies = 2,
+};
+
 static const struct onboard_hub_pdata realtek_rts5411_data = {
 	.reset_us = 0,
 	.num_supplies = 1,
@@ -50,6 +55,8 @@ static const struct of_device_id onboard_hub_match[] = {
 	{ .compatible = "usb424,2412", .data = &microchip_usb424_data, },
 	{ .compatible = "usb424,2514", .data = &microchip_usb424_data, },
 	{ .compatible = "usb424,2517", .data = &microchip_usb424_data, },
+	{ .compatible = "usb424,2744", .data = &microchip_usb5744_data, },
+	{ .compatible = "usb424,5744", .data = &microchip_usb5744_data, },
 	{ .compatible = "usb451,8140", .data = &ti_tusb8041_data, },
 	{ .compatible = "usb451,8142", .data = &ti_tusb8041_data, },
 	{ .compatible = "usb4b4,6504", .data = &cypress_hx3_data, },
diff --git a/drivers/usb/misc/usb-ljca.c b/drivers/usb/misc/usb-ljca.c
index c9decd0..35770e6 100644
--- a/drivers/usb/misc/usb-ljca.c
+++ b/drivers/usb/misc/usb-ljca.c
@@ -457,8 +457,8 @@ static void ljca_auxdev_acpi_bind(struct ljca_adapter *adap,
 				  u64 adr, u8 id)
 {
 	struct ljca_match_ids_walk_data wd = { 0 };
-	struct acpi_device *parent, *adev;
 	struct device *dev = adap->dev;
+	struct acpi_device *parent;
 	char uid[4];
 
 	parent = ACPI_COMPANION(dev);
@@ -466,17 +466,7 @@ static void ljca_auxdev_acpi_bind(struct ljca_adapter *adap,
 		return;
 
 	/*
-	 * get auxdev ACPI handle from the ACPI device directly
-	 * under the parent that matches _ADR.
-	 */
-	adev = acpi_find_child_device(parent, adr, false);
-	if (adev) {
-		ACPI_COMPANION_SET(&auxdev->dev, adev);
-		return;
-	}
-
-	/*
-	 * _ADR is a grey area in the ACPI specification, some
+	 * Currently LJCA hw doesn't use _ADR instead the shipped
 	 * platforms use _HID to distinguish children devices.
 	 */
 	switch (adr) {
@@ -656,10 +646,11 @@ static int ljca_enumerate_spi(struct ljca_adapter *adap)
 	unsigned int i;
 	int ret;
 
+	/* Not all LJCA chips implement SPI, a timeout reading the descriptors is normal */
 	ret = ljca_send(adap, LJCA_CLIENT_MNG, LJCA_MNG_ENUM_SPI, NULL, 0, buf,
 			sizeof(buf), true, LJCA_ENUM_CLIENT_TIMEOUT_MS);
 	if (ret < 0)
-		return ret;
+		return (ret == -ETIMEDOUT) ? 0 : ret;
 
 	/* check firmware response */
 	desc = (struct ljca_spi_descriptor *)buf;
diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
index 058d5b8..bfb6f948 100644
--- a/drivers/usb/typec/tcpm/tcpm.c
+++ b/drivers/usb/typec/tcpm/tcpm.c
@@ -4273,7 +4273,8 @@ static void run_state_machine(struct tcpm_port *port)
 				current_lim = PD_P_SNK_STDBY_MW / 5;
 			tcpm_set_current_limit(port, current_lim, 5000);
 			/* Not sink vbus if operational current is 0mA */
-			tcpm_set_charge(port, !!pdo_max_current(port->snk_pdo[0]));
+			tcpm_set_charge(port, !port->pd_supported ||
+					pdo_max_current(port->snk_pdo[0]));
 
 			if (!port->pd_supported)
 				tcpm_set_state(port, SNK_READY, 0);
@@ -5391,6 +5392,15 @@ static void _tcpm_pd_hard_reset(struct tcpm_port *port)
 	if (port->bist_request == BDO_MODE_TESTDATA && port->tcpc->set_bist_data)
 		port->tcpc->set_bist_data(port->tcpc, false);
 
+	switch (port->state) {
+	case ERROR_RECOVERY:
+	case PORT_RESET:
+	case PORT_RESET_WAIT_OFF:
+		return;
+	default:
+		break;
+	}
+
 	if (port->ams != NONE_AMS)
 		port->ams = NONE_AMS;
 	if (port->hard_reset_count < PD_N_HARD_RESET_COUNT)
diff --git a/drivers/usb/typec/tipd/core.c b/drivers/usb/typec/tipd/core.c
index 0e867f5..196535a 100644
--- a/drivers/usb/typec/tipd/core.c
+++ b/drivers/usb/typec/tipd/core.c
@@ -968,16 +968,17 @@ static int tps25750_start_patch_burst_mode(struct tps6598x *tps)
 	ret = of_property_match_string(np, "reg-names", "patch-address");
 	if (ret < 0) {
 		dev_err(tps->dev, "failed to get patch-address %d\n", ret);
-		return ret;
+		goto release_fw;
 	}
 
 	ret = of_property_read_u32_index(np, "reg", ret, &addr);
 	if (ret)
-		return ret;
+		goto release_fw;
 
 	if (addr == 0 || (addr >= 0x20 && addr <= 0x23)) {
 		dev_err(tps->dev, "wrong patch address %u\n", addr);
-		return -EINVAL;
+		ret = -EINVAL;
+		goto release_fw;
 	}
 
 	bpms_data.addr = (u8)addr;
@@ -1226,7 +1227,10 @@ static int tps6598x_probe(struct i2c_client *client)
 			TPS_REG_INT_PLUG_EVENT;
 	}
 
-	tps->data = device_get_match_data(tps->dev);
+	if (dev_fwnode(tps->dev))
+		tps->data = device_get_match_data(tps->dev);
+	else
+		tps->data = i2c_get_match_data(client);
 	if (!tps->data)
 		return -EINVAL;
 
@@ -1425,7 +1429,7 @@ static const struct of_device_id tps6598x_of_match[] = {
 MODULE_DEVICE_TABLE(of, tps6598x_of_match);
 
 static const struct i2c_device_id tps6598x_id[] = {
-	{ "tps6598x" },
+	{ "tps6598x", (kernel_ulong_t)&tps6598x_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, tps6598x_id);
diff --git a/include/linux/usb/phy.h b/include/linux/usb/phy.h
index b513749..e4de6bc 100644
--- a/include/linux/usb/phy.h
+++ b/include/linux/usb/phy.h
@@ -144,10 +144,6 @@ struct usb_phy {
 	 */
 	int	(*set_wakeup)(struct usb_phy *x, bool enabled);
 
-	/* notify phy port status change */
-	int	(*notify_port_status)(struct usb_phy *x, int port,
-				      u16 portstatus, u16 portchange);
-
 	/* notify phy connect status change */
 	int	(*notify_connect)(struct usb_phy *x,
 			enum usb_device_speed speed);
@@ -321,15 +317,6 @@ usb_phy_set_wakeup(struct usb_phy *x, bool enabled)
 }
 
 static inline int
-usb_phy_notify_port_status(struct usb_phy *x, int port, u16 portstatus, u16 portchange)
-{
-	if (x && x->notify_port_status)
-		return x->notify_port_status(x, port, portstatus, portchange);
-	else
-		return 0;
-}
-
-static inline int
 usb_phy_notify_connect(struct usb_phy *x, enum usb_device_speed speed)
 {
 	if (x && x->notify_connect)