| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * |
| * Copyright (C) STMicroelectronics SA 2017 |
| * Author(s): M'boumba Cedric Madianga <cedric.madianga@gmail.com> |
| * Pierre-Yves Mordret <pierre-yves.mordret@st.com> |
| * |
| * Driver for STM32 MDMA controller |
| * |
| * Inspired by stm32-dma.c and dma-jz4780.c |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/dmaengine.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/dmapool.h> |
| #include <linux/err.h> |
| #include <linux/init.h> |
| #include <linux/iopoll.h> |
| #include <linux/jiffies.h> |
| #include <linux/list.h> |
| #include <linux/log2.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/of_dma.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/reset.h> |
| #include <linux/slab.h> |
| |
| #include "virt-dma.h" |
| |
| #define STM32_MDMA_GISR0 0x0000 /* MDMA Int Status Reg 1 */ |
| |
| /* MDMA Channel x interrupt/status register */ |
| #define STM32_MDMA_CISR(x) (0x40 + 0x40 * (x)) /* x = 0..62 */ |
| #define STM32_MDMA_CISR_CRQA BIT(16) |
| #define STM32_MDMA_CISR_TCIF BIT(4) |
| #define STM32_MDMA_CISR_BTIF BIT(3) |
| #define STM32_MDMA_CISR_BRTIF BIT(2) |
| #define STM32_MDMA_CISR_CTCIF BIT(1) |
| #define STM32_MDMA_CISR_TEIF BIT(0) |
| |
| /* MDMA Channel x interrupt flag clear register */ |
| #define STM32_MDMA_CIFCR(x) (0x44 + 0x40 * (x)) |
| #define STM32_MDMA_CIFCR_CLTCIF BIT(4) |
| #define STM32_MDMA_CIFCR_CBTIF BIT(3) |
| #define STM32_MDMA_CIFCR_CBRTIF BIT(2) |
| #define STM32_MDMA_CIFCR_CCTCIF BIT(1) |
| #define STM32_MDMA_CIFCR_CTEIF BIT(0) |
| #define STM32_MDMA_CIFCR_CLEAR_ALL (STM32_MDMA_CIFCR_CLTCIF \ |
| | STM32_MDMA_CIFCR_CBTIF \ |
| | STM32_MDMA_CIFCR_CBRTIF \ |
| | STM32_MDMA_CIFCR_CCTCIF \ |
| | STM32_MDMA_CIFCR_CTEIF) |
| |
| /* MDMA Channel x error status register */ |
| #define STM32_MDMA_CESR(x) (0x48 + 0x40 * (x)) |
| #define STM32_MDMA_CESR_BSE BIT(11) |
| #define STM32_MDMA_CESR_ASR BIT(10) |
| #define STM32_MDMA_CESR_TEMD BIT(9) |
| #define STM32_MDMA_CESR_TELD BIT(8) |
| #define STM32_MDMA_CESR_TED BIT(7) |
| #define STM32_MDMA_CESR_TEA_MASK GENMASK(6, 0) |
| |
| /* MDMA Channel x control register */ |
| #define STM32_MDMA_CCR(x) (0x4C + 0x40 * (x)) |
| #define STM32_MDMA_CCR_SWRQ BIT(16) |
| #define STM32_MDMA_CCR_WEX BIT(14) |
| #define STM32_MDMA_CCR_HEX BIT(13) |
| #define STM32_MDMA_CCR_BEX BIT(12) |
| #define STM32_MDMA_CCR_SM BIT(8) |
| #define STM32_MDMA_CCR_PL_MASK GENMASK(7, 6) |
| #define STM32_MDMA_CCR_PL(n) FIELD_PREP(STM32_MDMA_CCR_PL_MASK, (n)) |
| #define STM32_MDMA_CCR_TCIE BIT(5) |
| #define STM32_MDMA_CCR_BTIE BIT(4) |
| #define STM32_MDMA_CCR_BRTIE BIT(3) |
| #define STM32_MDMA_CCR_CTCIE BIT(2) |
| #define STM32_MDMA_CCR_TEIE BIT(1) |
| #define STM32_MDMA_CCR_EN BIT(0) |
| #define STM32_MDMA_CCR_IRQ_MASK (STM32_MDMA_CCR_TCIE \ |
| | STM32_MDMA_CCR_BTIE \ |
| | STM32_MDMA_CCR_BRTIE \ |
| | STM32_MDMA_CCR_CTCIE \ |
| | STM32_MDMA_CCR_TEIE) |
| |
| /* MDMA Channel x transfer configuration register */ |
| #define STM32_MDMA_CTCR(x) (0x50 + 0x40 * (x)) |
| #define STM32_MDMA_CTCR_BWM BIT(31) |
| #define STM32_MDMA_CTCR_SWRM BIT(30) |
| #define STM32_MDMA_CTCR_TRGM_MSK GENMASK(29, 28) |
| #define STM32_MDMA_CTCR_TRGM(n) FIELD_PREP(STM32_MDMA_CTCR_TRGM_MSK, (n)) |
| #define STM32_MDMA_CTCR_TRGM_GET(n) FIELD_GET(STM32_MDMA_CTCR_TRGM_MSK, (n)) |
| #define STM32_MDMA_CTCR_PAM_MASK GENMASK(27, 26) |
| #define STM32_MDMA_CTCR_PAM(n) FIELD_PREP(STM32_MDMA_CTCR_PAM_MASK, (n)) |
| #define STM32_MDMA_CTCR_PKE BIT(25) |
| #define STM32_MDMA_CTCR_TLEN_MSK GENMASK(24, 18) |
| #define STM32_MDMA_CTCR_TLEN(n) FIELD_PREP(STM32_MDMA_CTCR_TLEN_MSK, (n)) |
| #define STM32_MDMA_CTCR_TLEN_GET(n) FIELD_GET(STM32_MDMA_CTCR_TLEN_MSK, (n)) |
| #define STM32_MDMA_CTCR_LEN2_MSK GENMASK(25, 18) |
| #define STM32_MDMA_CTCR_LEN2(n) FIELD_PREP(STM32_MDMA_CTCR_LEN2_MSK, (n)) |
| #define STM32_MDMA_CTCR_LEN2_GET(n) FIELD_GET(STM32_MDMA_CTCR_LEN2_MSK, (n)) |
| #define STM32_MDMA_CTCR_DBURST_MASK GENMASK(17, 15) |
| #define STM32_MDMA_CTCR_DBURST(n) FIELD_PREP(STM32_MDMA_CTCR_DBURST_MASK, (n)) |
| #define STM32_MDMA_CTCR_SBURST_MASK GENMASK(14, 12) |
| #define STM32_MDMA_CTCR_SBURST(n) FIELD_PREP(STM32_MDMA_CTCR_SBURST_MASK, (n)) |
| #define STM32_MDMA_CTCR_DINCOS_MASK GENMASK(11, 10) |
| #define STM32_MDMA_CTCR_DINCOS(n) FIELD_PREP(STM32_MDMA_CTCR_DINCOS_MASK, (n)) |
| #define STM32_MDMA_CTCR_SINCOS_MASK GENMASK(9, 8) |
| #define STM32_MDMA_CTCR_SINCOS(n) FIELD_PREP(STM32_MDMA_CTCR_SINCOS_MASK, (n)) |
| #define STM32_MDMA_CTCR_DSIZE_MASK GENMASK(7, 6) |
| #define STM32_MDMA_CTCR_DSIZE(n) FIELD_PREP(STM32_MDMA_CTCR_DSIZE_MASK, (n)) |
| #define STM32_MDMA_CTCR_SSIZE_MASK GENMASK(5, 4) |
| #define STM32_MDMA_CTCR_SSIZE(n) FIELD_PREP(STM32_MDMA_CTCR_SSIZE_MASK, (n)) |
| #define STM32_MDMA_CTCR_DINC_MASK GENMASK(3, 2) |
| #define STM32_MDMA_CTCR_DINC(n) FIELD_PREP(STM32_MDMA_CTCR_DINC_MASK, (n)) |
| #define STM32_MDMA_CTCR_SINC_MASK GENMASK(1, 0) |
| #define STM32_MDMA_CTCR_SINC(n) FIELD_PREP(STM32_MDMA_CTCR_SINC_MASK, (n)) |
| #define STM32_MDMA_CTCR_CFG_MASK (STM32_MDMA_CTCR_SINC_MASK \ |
| | STM32_MDMA_CTCR_DINC_MASK \ |
| | STM32_MDMA_CTCR_SINCOS_MASK \ |
| | STM32_MDMA_CTCR_DINCOS_MASK \ |
| | STM32_MDMA_CTCR_LEN2_MSK \ |
| | STM32_MDMA_CTCR_TRGM_MSK) |
| |
| /* MDMA Channel x block number of data register */ |
| #define STM32_MDMA_CBNDTR(x) (0x54 + 0x40 * (x)) |
| #define STM32_MDMA_CBNDTR_BRC_MK GENMASK(31, 20) |
| #define STM32_MDMA_CBNDTR_BRC(n) FIELD_PREP(STM32_MDMA_CBNDTR_BRC_MK, (n)) |
| #define STM32_MDMA_CBNDTR_BRC_GET(n) FIELD_GET(STM32_MDMA_CBNDTR_BRC_MK, (n)) |
| |
| #define STM32_MDMA_CBNDTR_BRDUM BIT(19) |
| #define STM32_MDMA_CBNDTR_BRSUM BIT(18) |
| #define STM32_MDMA_CBNDTR_BNDT_MASK GENMASK(16, 0) |
| #define STM32_MDMA_CBNDTR_BNDT(n) FIELD_PREP(STM32_MDMA_CBNDTR_BNDT_MASK, (n)) |
| |
| /* MDMA Channel x source address register */ |
| #define STM32_MDMA_CSAR(x) (0x58 + 0x40 * (x)) |
| |
| /* MDMA Channel x destination address register */ |
| #define STM32_MDMA_CDAR(x) (0x5C + 0x40 * (x)) |
| |
| /* MDMA Channel x block repeat address update register */ |
| #define STM32_MDMA_CBRUR(x) (0x60 + 0x40 * (x)) |
| #define STM32_MDMA_CBRUR_DUV_MASK GENMASK(31, 16) |
| #define STM32_MDMA_CBRUR_DUV(n) FIELD_PREP(STM32_MDMA_CBRUR_DUV_MASK, (n)) |
| #define STM32_MDMA_CBRUR_SUV_MASK GENMASK(15, 0) |
| #define STM32_MDMA_CBRUR_SUV(n) FIELD_PREP(STM32_MDMA_CBRUR_SUV_MASK, (n)) |
| |
| /* MDMA Channel x link address register */ |
| #define STM32_MDMA_CLAR(x) (0x64 + 0x40 * (x)) |
| |
| /* MDMA Channel x trigger and bus selection register */ |
| #define STM32_MDMA_CTBR(x) (0x68 + 0x40 * (x)) |
| #define STM32_MDMA_CTBR_DBUS BIT(17) |
| #define STM32_MDMA_CTBR_SBUS BIT(16) |
| #define STM32_MDMA_CTBR_TSEL_MASK GENMASK(5, 0) |
| #define STM32_MDMA_CTBR_TSEL(n) FIELD_PREP(STM32_MDMA_CTBR_TSEL_MASK, (n)) |
| |
| /* MDMA Channel x mask address register */ |
| #define STM32_MDMA_CMAR(x) (0x70 + 0x40 * (x)) |
| |
| /* MDMA Channel x mask data register */ |
| #define STM32_MDMA_CMDR(x) (0x74 + 0x40 * (x)) |
| |
| #define STM32_MDMA_MAX_BUF_LEN 128 |
| #define STM32_MDMA_MAX_BLOCK_LEN 65536 |
| #define STM32_MDMA_MAX_CHANNELS 32 |
| #define STM32_MDMA_MAX_REQUESTS 256 |
| #define STM32_MDMA_MAX_BURST 128 |
| #define STM32_MDMA_VERY_HIGH_PRIORITY 0x3 |
| |
| enum stm32_mdma_trigger_mode { |
| STM32_MDMA_BUFFER, |
| STM32_MDMA_BLOCK, |
| STM32_MDMA_BLOCK_REP, |
| STM32_MDMA_LINKED_LIST, |
| }; |
| |
| enum stm32_mdma_width { |
| STM32_MDMA_BYTE, |
| STM32_MDMA_HALF_WORD, |
| STM32_MDMA_WORD, |
| STM32_MDMA_DOUBLE_WORD, |
| }; |
| |
| enum stm32_mdma_inc_mode { |
| STM32_MDMA_FIXED = 0, |
| STM32_MDMA_INC = 2, |
| STM32_MDMA_DEC = 3, |
| }; |
| |
| struct stm32_mdma_chan_config { |
| u32 request; |
| u32 priority_level; |
| u32 transfer_config; |
| u32 mask_addr; |
| u32 mask_data; |
| bool m2m_hw; /* True when MDMA is triggered by STM32 DMA */ |
| }; |
| |
| struct stm32_mdma_hwdesc { |
| u32 ctcr; |
| u32 cbndtr; |
| u32 csar; |
| u32 cdar; |
| u32 cbrur; |
| u32 clar; |
| u32 ctbr; |
| u32 dummy; |
| u32 cmar; |
| u32 cmdr; |
| } __aligned(64); |
| |
| struct stm32_mdma_desc_node { |
| struct stm32_mdma_hwdesc *hwdesc; |
| dma_addr_t hwdesc_phys; |
| }; |
| |
| struct stm32_mdma_desc { |
| struct virt_dma_desc vdesc; |
| u32 ccr; |
| bool cyclic; |
| u32 count; |
| struct stm32_mdma_desc_node node[]; |
| }; |
| |
| struct stm32_mdma_dma_config { |
| u32 request; /* STM32 DMA channel stream id, triggering MDMA */ |
| u32 cmar; /* STM32 DMA interrupt flag clear register address */ |
| u32 cmdr; /* STM32 DMA Transfer Complete flag */ |
| }; |
| |
| struct stm32_mdma_chan { |
| struct virt_dma_chan vchan; |
| struct dma_pool *desc_pool; |
| u32 id; |
| struct stm32_mdma_desc *desc; |
| u32 curr_hwdesc; |
| struct dma_slave_config dma_config; |
| struct stm32_mdma_chan_config chan_config; |
| bool busy; |
| u32 mem_burst; |
| u32 mem_width; |
| }; |
| |
| struct stm32_mdma_device { |
| struct dma_device ddev; |
| void __iomem *base; |
| struct clk *clk; |
| int irq; |
| u32 nr_channels; |
| u32 nr_requests; |
| u32 nr_ahb_addr_masks; |
| u32 chan_reserved; |
| struct stm32_mdma_chan chan[STM32_MDMA_MAX_CHANNELS]; |
| u32 ahb_addr_masks[]; |
| }; |
| |
| static struct stm32_mdma_device *stm32_mdma_get_dev( |
| struct stm32_mdma_chan *chan) |
| { |
| return container_of(chan->vchan.chan.device, struct stm32_mdma_device, |
| ddev); |
| } |
| |
| static struct stm32_mdma_chan *to_stm32_mdma_chan(struct dma_chan *c) |
| { |
| return container_of(c, struct stm32_mdma_chan, vchan.chan); |
| } |
| |
| static struct stm32_mdma_desc *to_stm32_mdma_desc(struct virt_dma_desc *vdesc) |
| { |
| return container_of(vdesc, struct stm32_mdma_desc, vdesc); |
| } |
| |
| static struct device *chan2dev(struct stm32_mdma_chan *chan) |
| { |
| return &chan->vchan.chan.dev->device; |
| } |
| |
| static struct device *mdma2dev(struct stm32_mdma_device *mdma_dev) |
| { |
| return mdma_dev->ddev.dev; |
| } |
| |
| static u32 stm32_mdma_read(struct stm32_mdma_device *dmadev, u32 reg) |
| { |
| return readl_relaxed(dmadev->base + reg); |
| } |
| |
| static void stm32_mdma_write(struct stm32_mdma_device *dmadev, u32 reg, u32 val) |
| { |
| writel_relaxed(val, dmadev->base + reg); |
| } |
| |
| static void stm32_mdma_set_bits(struct stm32_mdma_device *dmadev, u32 reg, |
| u32 mask) |
| { |
| void __iomem *addr = dmadev->base + reg; |
| |
| writel_relaxed(readl_relaxed(addr) | mask, addr); |
| } |
| |
| static void stm32_mdma_clr_bits(struct stm32_mdma_device *dmadev, u32 reg, |
| u32 mask) |
| { |
| void __iomem *addr = dmadev->base + reg; |
| |
| writel_relaxed(readl_relaxed(addr) & ~mask, addr); |
| } |
| |
| static struct stm32_mdma_desc *stm32_mdma_alloc_desc( |
| struct stm32_mdma_chan *chan, u32 count) |
| { |
| struct stm32_mdma_desc *desc; |
| int i; |
| |
| desc = kzalloc(struct_size(desc, node, count), GFP_NOWAIT); |
| if (!desc) |
| return NULL; |
| |
| for (i = 0; i < count; i++) { |
| desc->node[i].hwdesc = |
| dma_pool_alloc(chan->desc_pool, GFP_NOWAIT, |
| &desc->node[i].hwdesc_phys); |
| if (!desc->node[i].hwdesc) |
| goto err; |
| } |
| |
| desc->count = count; |
| |
| return desc; |
| |
| err: |
| dev_err(chan2dev(chan), "Failed to allocate descriptor\n"); |
| while (--i >= 0) |
| dma_pool_free(chan->desc_pool, desc->node[i].hwdesc, |
| desc->node[i].hwdesc_phys); |
| kfree(desc); |
| return NULL; |
| } |
| |
| static void stm32_mdma_desc_free(struct virt_dma_desc *vdesc) |
| { |
| struct stm32_mdma_desc *desc = to_stm32_mdma_desc(vdesc); |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(vdesc->tx.chan); |
| int i; |
| |
| for (i = 0; i < desc->count; i++) |
| dma_pool_free(chan->desc_pool, desc->node[i].hwdesc, |
| desc->node[i].hwdesc_phys); |
| kfree(desc); |
| } |
| |
| static int stm32_mdma_get_width(struct stm32_mdma_chan *chan, |
| enum dma_slave_buswidth width) |
| { |
| switch (width) { |
| case DMA_SLAVE_BUSWIDTH_1_BYTE: |
| case DMA_SLAVE_BUSWIDTH_2_BYTES: |
| case DMA_SLAVE_BUSWIDTH_4_BYTES: |
| case DMA_SLAVE_BUSWIDTH_8_BYTES: |
| return ffs(width) - 1; |
| default: |
| dev_err(chan2dev(chan), "Dma bus width %i not supported\n", |
| width); |
| return -EINVAL; |
| } |
| } |
| |
| static enum dma_slave_buswidth stm32_mdma_get_max_width(dma_addr_t addr, |
| u32 buf_len, u32 tlen) |
| { |
| enum dma_slave_buswidth max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; |
| |
| for (max_width = DMA_SLAVE_BUSWIDTH_8_BYTES; |
| max_width > DMA_SLAVE_BUSWIDTH_1_BYTE; |
| max_width >>= 1) { |
| /* |
| * Address and buffer length both have to be aligned on |
| * bus width |
| */ |
| if ((((buf_len | addr) & (max_width - 1)) == 0) && |
| tlen >= max_width) |
| break; |
| } |
| |
| return max_width; |
| } |
| |
| static u32 stm32_mdma_get_best_burst(u32 buf_len, u32 tlen, u32 max_burst, |
| enum dma_slave_buswidth width) |
| { |
| u32 best_burst; |
| |
| best_burst = min((u32)1 << __ffs(tlen | buf_len), |
| max_burst * width) / width; |
| |
| return (best_burst > 0) ? best_burst : 1; |
| } |
| |
| static int stm32_mdma_disable_chan(struct stm32_mdma_chan *chan) |
| { |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| u32 ccr, cisr, id, reg; |
| int ret; |
| |
| id = chan->id; |
| reg = STM32_MDMA_CCR(id); |
| |
| /* Disable interrupts */ |
| stm32_mdma_clr_bits(dmadev, reg, STM32_MDMA_CCR_IRQ_MASK); |
| |
| ccr = stm32_mdma_read(dmadev, reg); |
| if (ccr & STM32_MDMA_CCR_EN) { |
| stm32_mdma_clr_bits(dmadev, reg, STM32_MDMA_CCR_EN); |
| |
| /* Ensure that any ongoing transfer has been completed */ |
| ret = readl_relaxed_poll_timeout_atomic( |
| dmadev->base + STM32_MDMA_CISR(id), cisr, |
| (cisr & STM32_MDMA_CISR_CTCIF), 10, 1000); |
| if (ret) { |
| dev_err(chan2dev(chan), "%s: timeout!\n", __func__); |
| return -EBUSY; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void stm32_mdma_stop(struct stm32_mdma_chan *chan) |
| { |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| u32 status; |
| int ret; |
| |
| /* Disable DMA */ |
| ret = stm32_mdma_disable_chan(chan); |
| if (ret < 0) |
| return; |
| |
| /* Clear interrupt status if it is there */ |
| status = stm32_mdma_read(dmadev, STM32_MDMA_CISR(chan->id)); |
| if (status) { |
| dev_dbg(chan2dev(chan), "%s(): clearing interrupt: 0x%08x\n", |
| __func__, status); |
| stm32_mdma_set_bits(dmadev, STM32_MDMA_CIFCR(chan->id), status); |
| } |
| |
| chan->busy = false; |
| } |
| |
| static void stm32_mdma_set_bus(struct stm32_mdma_device *dmadev, u32 *ctbr, |
| u32 ctbr_mask, u32 src_addr) |
| { |
| u32 mask; |
| int i; |
| |
| /* Check if memory device is on AHB or AXI */ |
| *ctbr &= ~ctbr_mask; |
| mask = src_addr & 0xF0000000; |
| for (i = 0; i < dmadev->nr_ahb_addr_masks; i++) { |
| if (mask == dmadev->ahb_addr_masks[i]) { |
| *ctbr |= ctbr_mask; |
| break; |
| } |
| } |
| } |
| |
| static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan, |
| enum dma_transfer_direction direction, |
| u32 *mdma_ccr, u32 *mdma_ctcr, |
| u32 *mdma_ctbr, dma_addr_t addr, |
| u32 buf_len) |
| { |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| struct stm32_mdma_chan_config *chan_config = &chan->chan_config; |
| enum dma_slave_buswidth src_addr_width, dst_addr_width; |
| phys_addr_t src_addr, dst_addr; |
| int src_bus_width, dst_bus_width; |
| u32 src_maxburst, dst_maxburst, src_best_burst, dst_best_burst; |
| u32 ccr, ctcr, ctbr, tlen; |
| |
| src_addr_width = chan->dma_config.src_addr_width; |
| dst_addr_width = chan->dma_config.dst_addr_width; |
| src_maxburst = chan->dma_config.src_maxburst; |
| dst_maxburst = chan->dma_config.dst_maxburst; |
| |
| ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id)); |
| ctcr = stm32_mdma_read(dmadev, STM32_MDMA_CTCR(chan->id)); |
| ctbr = stm32_mdma_read(dmadev, STM32_MDMA_CTBR(chan->id)); |
| |
| /* Enable HW request mode */ |
| ctcr &= ~STM32_MDMA_CTCR_SWRM; |
| |
| /* Set DINC, SINC, DINCOS, SINCOS, TRGM and TLEN retrieve from DT */ |
| ctcr &= ~STM32_MDMA_CTCR_CFG_MASK; |
| ctcr |= chan_config->transfer_config & STM32_MDMA_CTCR_CFG_MASK; |
| |
| /* |
| * For buffer transfer length (TLEN) we have to set |
| * the number of bytes - 1 in CTCR register |
| */ |
| tlen = STM32_MDMA_CTCR_LEN2_GET(ctcr); |
| ctcr &= ~STM32_MDMA_CTCR_LEN2_MSK; |
| ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); |
| |
| /* Disable Pack Enable */ |
| ctcr &= ~STM32_MDMA_CTCR_PKE; |
| |
| /* Check burst size constraints */ |
| if (src_maxburst * src_addr_width > STM32_MDMA_MAX_BURST || |
| dst_maxburst * dst_addr_width > STM32_MDMA_MAX_BURST) { |
| dev_err(chan2dev(chan), |
| "burst size * bus width higher than %d bytes\n", |
| STM32_MDMA_MAX_BURST); |
| return -EINVAL; |
| } |
| |
| if ((!is_power_of_2(src_maxburst) && src_maxburst > 0) || |
| (!is_power_of_2(dst_maxburst) && dst_maxburst > 0)) { |
| dev_err(chan2dev(chan), "burst size must be a power of 2\n"); |
| return -EINVAL; |
| } |
| |
| /* |
| * Configure channel control: |
| * - Clear SW request as in this case this is a HW one |
| * - Clear WEX, HEX and BEX bits |
| * - Set priority level |
| */ |
| ccr &= ~(STM32_MDMA_CCR_SWRQ | STM32_MDMA_CCR_WEX | STM32_MDMA_CCR_HEX | |
| STM32_MDMA_CCR_BEX | STM32_MDMA_CCR_PL_MASK); |
| ccr |= STM32_MDMA_CCR_PL(chan_config->priority_level); |
| |
| /* Configure Trigger selection */ |
| ctbr &= ~STM32_MDMA_CTBR_TSEL_MASK; |
| ctbr |= STM32_MDMA_CTBR_TSEL(chan_config->request); |
| |
| switch (direction) { |
| case DMA_MEM_TO_DEV: |
| dst_addr = chan->dma_config.dst_addr; |
| |
| /* Set device data size */ |
| if (chan_config->m2m_hw) |
| dst_addr_width = stm32_mdma_get_max_width(dst_addr, buf_len, |
| STM32_MDMA_MAX_BUF_LEN); |
| dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); |
| if (dst_bus_width < 0) |
| return dst_bus_width; |
| ctcr &= ~STM32_MDMA_CTCR_DSIZE_MASK; |
| ctcr |= STM32_MDMA_CTCR_DSIZE(dst_bus_width); |
| if (chan_config->m2m_hw) { |
| ctcr &= ~STM32_MDMA_CTCR_DINCOS_MASK; |
| ctcr |= STM32_MDMA_CTCR_DINCOS(dst_bus_width); |
| } |
| |
| /* Set device burst value */ |
| if (chan_config->m2m_hw) |
| dst_maxburst = STM32_MDMA_MAX_BUF_LEN / dst_addr_width; |
| |
| dst_best_burst = stm32_mdma_get_best_burst(buf_len, tlen, |
| dst_maxburst, |
| dst_addr_width); |
| chan->mem_burst = dst_best_burst; |
| ctcr &= ~STM32_MDMA_CTCR_DBURST_MASK; |
| ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); |
| |
| /* Set memory data size */ |
| src_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); |
| chan->mem_width = src_addr_width; |
| src_bus_width = stm32_mdma_get_width(chan, src_addr_width); |
| if (src_bus_width < 0) |
| return src_bus_width; |
| ctcr &= ~STM32_MDMA_CTCR_SSIZE_MASK | |
| STM32_MDMA_CTCR_SINCOS_MASK; |
| ctcr |= STM32_MDMA_CTCR_SSIZE(src_bus_width) | |
| STM32_MDMA_CTCR_SINCOS(src_bus_width); |
| |
| /* Set memory burst value */ |
| src_maxburst = STM32_MDMA_MAX_BUF_LEN / src_addr_width; |
| src_best_burst = stm32_mdma_get_best_burst(buf_len, tlen, |
| src_maxburst, |
| src_addr_width); |
| chan->mem_burst = src_best_burst; |
| ctcr &= ~STM32_MDMA_CTCR_SBURST_MASK; |
| ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); |
| |
| /* Select bus */ |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, |
| dst_addr); |
| |
| if (dst_bus_width != src_bus_width) |
| ctcr |= STM32_MDMA_CTCR_PKE; |
| |
| /* Set destination address */ |
| stm32_mdma_write(dmadev, STM32_MDMA_CDAR(chan->id), dst_addr); |
| break; |
| |
| case DMA_DEV_TO_MEM: |
| src_addr = chan->dma_config.src_addr; |
| |
| /* Set device data size */ |
| if (chan_config->m2m_hw) |
| src_addr_width = stm32_mdma_get_max_width(src_addr, buf_len, |
| STM32_MDMA_MAX_BUF_LEN); |
| |
| src_bus_width = stm32_mdma_get_width(chan, src_addr_width); |
| if (src_bus_width < 0) |
| return src_bus_width; |
| ctcr &= ~STM32_MDMA_CTCR_SSIZE_MASK; |
| ctcr |= STM32_MDMA_CTCR_SSIZE(src_bus_width); |
| if (chan_config->m2m_hw) { |
| ctcr &= ~STM32_MDMA_CTCR_SINCOS_MASK; |
| ctcr |= STM32_MDMA_CTCR_SINCOS(src_bus_width); |
| } |
| |
| /* Set device burst value */ |
| if (chan_config->m2m_hw) |
| src_maxburst = STM32_MDMA_MAX_BUF_LEN / src_addr_width; |
| |
| src_best_burst = stm32_mdma_get_best_burst(buf_len, tlen, |
| src_maxburst, |
| src_addr_width); |
| ctcr &= ~STM32_MDMA_CTCR_SBURST_MASK; |
| ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst))); |
| |
| /* Set memory data size */ |
| dst_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen); |
| chan->mem_width = dst_addr_width; |
| dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width); |
| if (dst_bus_width < 0) |
| return dst_bus_width; |
| ctcr &= ~(STM32_MDMA_CTCR_DSIZE_MASK | |
| STM32_MDMA_CTCR_DINCOS_MASK); |
| ctcr |= STM32_MDMA_CTCR_DSIZE(dst_bus_width) | |
| STM32_MDMA_CTCR_DINCOS(dst_bus_width); |
| |
| /* Set memory burst value */ |
| dst_maxburst = STM32_MDMA_MAX_BUF_LEN / dst_addr_width; |
| dst_best_burst = stm32_mdma_get_best_burst(buf_len, tlen, |
| dst_maxburst, |
| dst_addr_width); |
| ctcr &= ~STM32_MDMA_CTCR_DBURST_MASK; |
| ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst))); |
| |
| /* Select bus */ |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, |
| src_addr); |
| |
| if (dst_bus_width != src_bus_width) |
| ctcr |= STM32_MDMA_CTCR_PKE; |
| |
| /* Set source address */ |
| stm32_mdma_write(dmadev, STM32_MDMA_CSAR(chan->id), src_addr); |
| break; |
| |
| default: |
| dev_err(chan2dev(chan), "Dma direction is not supported\n"); |
| return -EINVAL; |
| } |
| |
| *mdma_ccr = ccr; |
| *mdma_ctcr = ctcr; |
| *mdma_ctbr = ctbr; |
| |
| return 0; |
| } |
| |
| static void stm32_mdma_dump_hwdesc(struct stm32_mdma_chan *chan, |
| struct stm32_mdma_desc_node *node) |
| { |
| dev_dbg(chan2dev(chan), "hwdesc: %pad\n", &node->hwdesc_phys); |
| dev_dbg(chan2dev(chan), "CTCR: 0x%08x\n", node->hwdesc->ctcr); |
| dev_dbg(chan2dev(chan), "CBNDTR: 0x%08x\n", node->hwdesc->cbndtr); |
| dev_dbg(chan2dev(chan), "CSAR: 0x%08x\n", node->hwdesc->csar); |
| dev_dbg(chan2dev(chan), "CDAR: 0x%08x\n", node->hwdesc->cdar); |
| dev_dbg(chan2dev(chan), "CBRUR: 0x%08x\n", node->hwdesc->cbrur); |
| dev_dbg(chan2dev(chan), "CLAR: 0x%08x\n", node->hwdesc->clar); |
| dev_dbg(chan2dev(chan), "CTBR: 0x%08x\n", node->hwdesc->ctbr); |
| dev_dbg(chan2dev(chan), "CMAR: 0x%08x\n", node->hwdesc->cmar); |
| dev_dbg(chan2dev(chan), "CMDR: 0x%08x\n\n", node->hwdesc->cmdr); |
| } |
| |
| static void stm32_mdma_setup_hwdesc(struct stm32_mdma_chan *chan, |
| struct stm32_mdma_desc *desc, |
| enum dma_transfer_direction dir, u32 count, |
| dma_addr_t src_addr, dma_addr_t dst_addr, |
| u32 len, u32 ctcr, u32 ctbr, bool is_last, |
| bool is_first, bool is_cyclic) |
| { |
| struct stm32_mdma_chan_config *config = &chan->chan_config; |
| struct stm32_mdma_hwdesc *hwdesc; |
| u32 next = count + 1; |
| |
| hwdesc = desc->node[count].hwdesc; |
| hwdesc->ctcr = ctcr; |
| hwdesc->cbndtr &= ~(STM32_MDMA_CBNDTR_BRC_MK | |
| STM32_MDMA_CBNDTR_BRDUM | |
| STM32_MDMA_CBNDTR_BRSUM | |
| STM32_MDMA_CBNDTR_BNDT_MASK); |
| hwdesc->cbndtr |= STM32_MDMA_CBNDTR_BNDT(len); |
| hwdesc->csar = src_addr; |
| hwdesc->cdar = dst_addr; |
| hwdesc->cbrur = 0; |
| hwdesc->ctbr = ctbr; |
| hwdesc->cmar = config->mask_addr; |
| hwdesc->cmdr = config->mask_data; |
| |
| if (is_last) { |
| if (is_cyclic) |
| hwdesc->clar = desc->node[0].hwdesc_phys; |
| else |
| hwdesc->clar = 0; |
| } else { |
| hwdesc->clar = desc->node[next].hwdesc_phys; |
| } |
| |
| stm32_mdma_dump_hwdesc(chan, &desc->node[count]); |
| } |
| |
| static int stm32_mdma_setup_xfer(struct stm32_mdma_chan *chan, |
| struct stm32_mdma_desc *desc, |
| struct scatterlist *sgl, u32 sg_len, |
| enum dma_transfer_direction direction) |
| { |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| struct dma_slave_config *dma_config = &chan->dma_config; |
| struct stm32_mdma_chan_config *chan_config = &chan->chan_config; |
| struct scatterlist *sg; |
| dma_addr_t src_addr, dst_addr; |
| u32 m2m_hw_period, ccr, ctcr, ctbr; |
| int i, ret = 0; |
| |
| if (chan_config->m2m_hw) |
| m2m_hw_period = sg_dma_len(sgl); |
| |
| for_each_sg(sgl, sg, sg_len, i) { |
| if (sg_dma_len(sg) > STM32_MDMA_MAX_BLOCK_LEN) { |
| dev_err(chan2dev(chan), "Invalid block len\n"); |
| return -EINVAL; |
| } |
| |
| if (direction == DMA_MEM_TO_DEV) { |
| src_addr = sg_dma_address(sg); |
| dst_addr = dma_config->dst_addr; |
| if (chan_config->m2m_hw && (i & 1)) |
| dst_addr += m2m_hw_period; |
| ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, |
| &ctcr, &ctbr, src_addr, |
| sg_dma_len(sg)); |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, |
| src_addr); |
| } else { |
| src_addr = dma_config->src_addr; |
| if (chan_config->m2m_hw && (i & 1)) |
| src_addr += m2m_hw_period; |
| dst_addr = sg_dma_address(sg); |
| ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, |
| &ctcr, &ctbr, dst_addr, |
| sg_dma_len(sg)); |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, |
| dst_addr); |
| } |
| |
| if (ret < 0) |
| return ret; |
| |
| stm32_mdma_setup_hwdesc(chan, desc, direction, i, src_addr, |
| dst_addr, sg_dma_len(sg), ctcr, ctbr, |
| i == sg_len - 1, i == 0, false); |
| } |
| |
| /* Enable interrupts */ |
| ccr &= ~STM32_MDMA_CCR_IRQ_MASK; |
| ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE; |
| if (sg_len > 1) |
| ccr |= STM32_MDMA_CCR_BTIE; |
| desc->ccr = ccr; |
| |
| return 0; |
| } |
| |
| static struct dma_async_tx_descriptor * |
| stm32_mdma_prep_slave_sg(struct dma_chan *c, struct scatterlist *sgl, |
| u32 sg_len, enum dma_transfer_direction direction, |
| unsigned long flags, void *context) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct stm32_mdma_chan_config *chan_config = &chan->chan_config; |
| struct stm32_mdma_desc *desc; |
| int i, ret; |
| |
| /* |
| * Once DMA is in setup cyclic mode the channel we cannot assign this |
| * channel anymore. The DMA channel needs to be aborted or terminated |
| * for allowing another request. |
| */ |
| if (chan->desc && chan->desc->cyclic) { |
| dev_err(chan2dev(chan), |
| "Request not allowed when dma in cyclic mode\n"); |
| return NULL; |
| } |
| |
| desc = stm32_mdma_alloc_desc(chan, sg_len); |
| if (!desc) |
| return NULL; |
| |
| ret = stm32_mdma_setup_xfer(chan, desc, sgl, sg_len, direction); |
| if (ret < 0) |
| goto xfer_setup_err; |
| |
| /* |
| * In case of M2M HW transfer triggered by STM32 DMA, we do not have to clear the |
| * transfer complete flag by hardware in order to let the CPU rearm the STM32 DMA |
| * with the next sg element and update some data in dmaengine framework. |
| */ |
| if (chan_config->m2m_hw && direction == DMA_MEM_TO_DEV) { |
| struct stm32_mdma_hwdesc *hwdesc; |
| |
| for (i = 0; i < sg_len; i++) { |
| hwdesc = desc->node[i].hwdesc; |
| hwdesc->cmar = 0; |
| hwdesc->cmdr = 0; |
| } |
| } |
| |
| desc->cyclic = false; |
| |
| return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags); |
| |
| xfer_setup_err: |
| for (i = 0; i < desc->count; i++) |
| dma_pool_free(chan->desc_pool, desc->node[i].hwdesc, |
| desc->node[i].hwdesc_phys); |
| kfree(desc); |
| return NULL; |
| } |
| |
| static struct dma_async_tx_descriptor * |
| stm32_mdma_prep_dma_cyclic(struct dma_chan *c, dma_addr_t buf_addr, |
| size_t buf_len, size_t period_len, |
| enum dma_transfer_direction direction, |
| unsigned long flags) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| struct dma_slave_config *dma_config = &chan->dma_config; |
| struct stm32_mdma_chan_config *chan_config = &chan->chan_config; |
| struct stm32_mdma_desc *desc; |
| dma_addr_t src_addr, dst_addr; |
| u32 ccr, ctcr, ctbr, count; |
| int i, ret; |
| |
| /* |
| * Once DMA is in setup cyclic mode the channel we cannot assign this |
| * channel anymore. The DMA channel needs to be aborted or terminated |
| * for allowing another request. |
| */ |
| if (chan->desc && chan->desc->cyclic) { |
| dev_err(chan2dev(chan), |
| "Request not allowed when dma in cyclic mode\n"); |
| return NULL; |
| } |
| |
| if (!buf_len || !period_len || period_len > STM32_MDMA_MAX_BLOCK_LEN) { |
| dev_err(chan2dev(chan), "Invalid buffer/period len\n"); |
| return NULL; |
| } |
| |
| if (buf_len % period_len) { |
| dev_err(chan2dev(chan), "buf_len not multiple of period_len\n"); |
| return NULL; |
| } |
| |
| count = buf_len / period_len; |
| |
| desc = stm32_mdma_alloc_desc(chan, count); |
| if (!desc) |
| return NULL; |
| |
| /* Select bus */ |
| if (direction == DMA_MEM_TO_DEV) { |
| src_addr = buf_addr; |
| ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, |
| &ctbr, src_addr, period_len); |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, |
| src_addr); |
| } else { |
| dst_addr = buf_addr; |
| ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, |
| &ctbr, dst_addr, period_len); |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, |
| dst_addr); |
| } |
| |
| if (ret < 0) |
| goto xfer_setup_err; |
| |
| /* Enable interrupts */ |
| ccr &= ~STM32_MDMA_CCR_IRQ_MASK; |
| ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE; |
| desc->ccr = ccr; |
| |
| /* Configure hwdesc list */ |
| for (i = 0; i < count; i++) { |
| if (direction == DMA_MEM_TO_DEV) { |
| src_addr = buf_addr + i * period_len; |
| dst_addr = dma_config->dst_addr; |
| if (chan_config->m2m_hw && (i & 1)) |
| dst_addr += period_len; |
| } else { |
| src_addr = dma_config->src_addr; |
| if (chan_config->m2m_hw && (i & 1)) |
| src_addr += period_len; |
| dst_addr = buf_addr + i * period_len; |
| } |
| |
| stm32_mdma_setup_hwdesc(chan, desc, direction, i, src_addr, |
| dst_addr, period_len, ctcr, ctbr, |
| i == count - 1, i == 0, true); |
| } |
| |
| desc->cyclic = true; |
| |
| return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags); |
| |
| xfer_setup_err: |
| for (i = 0; i < desc->count; i++) |
| dma_pool_free(chan->desc_pool, desc->node[i].hwdesc, |
| desc->node[i].hwdesc_phys); |
| kfree(desc); |
| return NULL; |
| } |
| |
| static struct dma_async_tx_descriptor * |
| stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src, |
| size_t len, unsigned long flags) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| enum dma_slave_buswidth max_width; |
| struct stm32_mdma_desc *desc; |
| struct stm32_mdma_hwdesc *hwdesc; |
| u32 ccr, ctcr, ctbr, cbndtr, count, max_burst, mdma_burst; |
| u32 best_burst, tlen; |
| size_t xfer_count, offset; |
| int src_bus_width, dst_bus_width; |
| int i; |
| |
| /* |
| * Once DMA is in setup cyclic mode the channel we cannot assign this |
| * channel anymore. The DMA channel needs to be aborted or terminated |
| * to allow another request |
| */ |
| if (chan->desc && chan->desc->cyclic) { |
| dev_err(chan2dev(chan), |
| "Request not allowed when dma in cyclic mode\n"); |
| return NULL; |
| } |
| |
| count = DIV_ROUND_UP(len, STM32_MDMA_MAX_BLOCK_LEN); |
| desc = stm32_mdma_alloc_desc(chan, count); |
| if (!desc) |
| return NULL; |
| |
| ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id)); |
| ctcr = stm32_mdma_read(dmadev, STM32_MDMA_CTCR(chan->id)); |
| ctbr = stm32_mdma_read(dmadev, STM32_MDMA_CTBR(chan->id)); |
| cbndtr = stm32_mdma_read(dmadev, STM32_MDMA_CBNDTR(chan->id)); |
| |
| /* Enable sw req, some interrupts and clear other bits */ |
| ccr &= ~(STM32_MDMA_CCR_WEX | STM32_MDMA_CCR_HEX | |
| STM32_MDMA_CCR_BEX | STM32_MDMA_CCR_PL_MASK | |
| STM32_MDMA_CCR_IRQ_MASK); |
| ccr |= STM32_MDMA_CCR_TEIE; |
| |
| /* Enable SW request mode, dest/src inc and clear other bits */ |
| ctcr &= ~(STM32_MDMA_CTCR_BWM | STM32_MDMA_CTCR_TRGM_MSK | |
| STM32_MDMA_CTCR_PAM_MASK | STM32_MDMA_CTCR_PKE | |
| STM32_MDMA_CTCR_TLEN_MSK | STM32_MDMA_CTCR_DBURST_MASK | |
| STM32_MDMA_CTCR_SBURST_MASK | STM32_MDMA_CTCR_DINCOS_MASK | |
| STM32_MDMA_CTCR_SINCOS_MASK | STM32_MDMA_CTCR_DSIZE_MASK | |
| STM32_MDMA_CTCR_SSIZE_MASK | STM32_MDMA_CTCR_DINC_MASK | |
| STM32_MDMA_CTCR_SINC_MASK); |
| ctcr |= STM32_MDMA_CTCR_SWRM | STM32_MDMA_CTCR_SINC(STM32_MDMA_INC) | |
| STM32_MDMA_CTCR_DINC(STM32_MDMA_INC); |
| |
| /* Reset HW request */ |
| ctbr &= ~STM32_MDMA_CTBR_TSEL_MASK; |
| |
| /* Select bus */ |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS, src); |
| stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS, dest); |
| |
| /* Clear CBNDTR registers */ |
| cbndtr &= ~(STM32_MDMA_CBNDTR_BRC_MK | STM32_MDMA_CBNDTR_BRDUM | |
| STM32_MDMA_CBNDTR_BRSUM | STM32_MDMA_CBNDTR_BNDT_MASK); |
| |
| if (len <= STM32_MDMA_MAX_BLOCK_LEN) { |
| cbndtr |= STM32_MDMA_CBNDTR_BNDT(len); |
| if (len <= STM32_MDMA_MAX_BUF_LEN) { |
| /* Setup a buffer transfer */ |
| ccr |= STM32_MDMA_CCR_TCIE | STM32_MDMA_CCR_CTCIE; |
| ctcr |= STM32_MDMA_CTCR_TRGM(STM32_MDMA_BUFFER); |
| } else { |
| /* Setup a block transfer */ |
| ccr |= STM32_MDMA_CCR_BTIE | STM32_MDMA_CCR_CTCIE; |
| ctcr |= STM32_MDMA_CTCR_TRGM(STM32_MDMA_BLOCK); |
| } |
| |
| tlen = STM32_MDMA_MAX_BUF_LEN; |
| ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1)); |
| |
| /* Set source best burst size */ |
| max_width = stm32_mdma_get_max_width(src, len, tlen); |
| src_bus_width = stm32_mdma_get_width(chan, max_width); |
| |
| max_burst = tlen / max_width; |
| best_burst = stm32_mdma_get_best_burst(len, tlen, max_burst, |
| max_width); |
| mdma_burst = ilog2(best_burst); |
| |
| ctcr |= STM32_MDMA_CTCR_SBURST(mdma_burst) | |
| STM32_MDMA_CTCR_SSIZE(src_bus_width) | |
| STM32_MDMA_CTCR_SINCOS(src_bus_width); |
| |
| /* Set destination best burst size */ |
| max_width = stm32_mdma_get_max_width(dest, len, tlen); |
| dst_bus_width = stm32_mdma_get_width(chan, max_width); |
| |
| max_burst = tlen / max_width; |
| best_burst = stm32_mdma_get_best_burst(len, tlen, max_burst, |
| max_width); |
| mdma_burst = ilog2(best_burst); |
| |
| ctcr |= STM32_MDMA_CTCR_DBURST(mdma_burst) | |
| STM32_MDMA_CTCR_DSIZE(dst_bus_width) | |
| STM32_MDMA_CTCR_DINCOS(dst_bus_width); |
| |
| if (dst_bus_width != src_bus_width) |
| ctcr |= STM32_MDMA_CTCR_PKE; |
| |
| /* Prepare hardware descriptor */ |
| hwdesc = desc->node[0].hwdesc; |
| hwdesc->ctcr = ctcr; |
| hwdesc->cbndtr = cbndtr; |
| hwdesc->csar = src; |
| hwdesc->cdar = dest; |
| hwdesc->cbrur = 0; |
| hwdesc->clar = 0; |
| hwdesc->ctbr = ctbr; |
| hwdesc->cmar = 0; |
| hwdesc->cmdr = 0; |
| |
| stm32_mdma_dump_hwdesc(chan, &desc->node[0]); |
| } else { |
| /* Setup a LLI transfer */ |
| ctcr |= STM32_MDMA_CTCR_TRGM(STM32_MDMA_LINKED_LIST) | |
| STM32_MDMA_CTCR_TLEN((STM32_MDMA_MAX_BUF_LEN - 1)); |
| ccr |= STM32_MDMA_CCR_BTIE | STM32_MDMA_CCR_CTCIE; |
| tlen = STM32_MDMA_MAX_BUF_LEN; |
| |
| for (i = 0, offset = 0; offset < len; |
| i++, offset += xfer_count) { |
| xfer_count = min_t(size_t, len - offset, |
| STM32_MDMA_MAX_BLOCK_LEN); |
| |
| /* Set source best burst size */ |
| max_width = stm32_mdma_get_max_width(src, len, tlen); |
| src_bus_width = stm32_mdma_get_width(chan, max_width); |
| |
| max_burst = tlen / max_width; |
| best_burst = stm32_mdma_get_best_burst(len, tlen, |
| max_burst, |
| max_width); |
| mdma_burst = ilog2(best_burst); |
| |
| ctcr |= STM32_MDMA_CTCR_SBURST(mdma_burst) | |
| STM32_MDMA_CTCR_SSIZE(src_bus_width) | |
| STM32_MDMA_CTCR_SINCOS(src_bus_width); |
| |
| /* Set destination best burst size */ |
| max_width = stm32_mdma_get_max_width(dest, len, tlen); |
| dst_bus_width = stm32_mdma_get_width(chan, max_width); |
| |
| max_burst = tlen / max_width; |
| best_burst = stm32_mdma_get_best_burst(len, tlen, |
| max_burst, |
| max_width); |
| mdma_burst = ilog2(best_burst); |
| |
| ctcr |= STM32_MDMA_CTCR_DBURST(mdma_burst) | |
| STM32_MDMA_CTCR_DSIZE(dst_bus_width) | |
| STM32_MDMA_CTCR_DINCOS(dst_bus_width); |
| |
| if (dst_bus_width != src_bus_width) |
| ctcr |= STM32_MDMA_CTCR_PKE; |
| |
| /* Prepare hardware descriptor */ |
| stm32_mdma_setup_hwdesc(chan, desc, DMA_MEM_TO_MEM, i, |
| src + offset, dest + offset, |
| xfer_count, ctcr, ctbr, |
| i == count - 1, i == 0, false); |
| } |
| } |
| |
| desc->ccr = ccr; |
| |
| desc->cyclic = false; |
| |
| return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags); |
| } |
| |
| static void stm32_mdma_dump_reg(struct stm32_mdma_chan *chan) |
| { |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| |
| dev_dbg(chan2dev(chan), "CCR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CCR(chan->id))); |
| dev_dbg(chan2dev(chan), "CTCR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CTCR(chan->id))); |
| dev_dbg(chan2dev(chan), "CBNDTR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CBNDTR(chan->id))); |
| dev_dbg(chan2dev(chan), "CSAR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CSAR(chan->id))); |
| dev_dbg(chan2dev(chan), "CDAR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CDAR(chan->id))); |
| dev_dbg(chan2dev(chan), "CBRUR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CBRUR(chan->id))); |
| dev_dbg(chan2dev(chan), "CLAR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CLAR(chan->id))); |
| dev_dbg(chan2dev(chan), "CTBR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CTBR(chan->id))); |
| dev_dbg(chan2dev(chan), "CMAR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CMAR(chan->id))); |
| dev_dbg(chan2dev(chan), "CMDR: 0x%08x\n", |
| stm32_mdma_read(dmadev, STM32_MDMA_CMDR(chan->id))); |
| } |
| |
| static void stm32_mdma_start_transfer(struct stm32_mdma_chan *chan) |
| { |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| struct virt_dma_desc *vdesc; |
| struct stm32_mdma_hwdesc *hwdesc; |
| u32 id = chan->id; |
| u32 status, reg; |
| |
| vdesc = vchan_next_desc(&chan->vchan); |
| if (!vdesc) { |
| chan->desc = NULL; |
| return; |
| } |
| |
| list_del(&vdesc->node); |
| |
| chan->desc = to_stm32_mdma_desc(vdesc); |
| hwdesc = chan->desc->node[0].hwdesc; |
| chan->curr_hwdesc = 0; |
| |
| stm32_mdma_write(dmadev, STM32_MDMA_CCR(id), chan->desc->ccr); |
| stm32_mdma_write(dmadev, STM32_MDMA_CTCR(id), hwdesc->ctcr); |
| stm32_mdma_write(dmadev, STM32_MDMA_CBNDTR(id), hwdesc->cbndtr); |
| stm32_mdma_write(dmadev, STM32_MDMA_CSAR(id), hwdesc->csar); |
| stm32_mdma_write(dmadev, STM32_MDMA_CDAR(id), hwdesc->cdar); |
| stm32_mdma_write(dmadev, STM32_MDMA_CBRUR(id), hwdesc->cbrur); |
| stm32_mdma_write(dmadev, STM32_MDMA_CLAR(id), hwdesc->clar); |
| stm32_mdma_write(dmadev, STM32_MDMA_CTBR(id), hwdesc->ctbr); |
| stm32_mdma_write(dmadev, STM32_MDMA_CMAR(id), hwdesc->cmar); |
| stm32_mdma_write(dmadev, STM32_MDMA_CMDR(id), hwdesc->cmdr); |
| |
| /* Clear interrupt status if it is there */ |
| status = stm32_mdma_read(dmadev, STM32_MDMA_CISR(id)); |
| if (status) |
| stm32_mdma_set_bits(dmadev, STM32_MDMA_CIFCR(id), status); |
| |
| stm32_mdma_dump_reg(chan); |
| |
| /* Start DMA */ |
| stm32_mdma_set_bits(dmadev, STM32_MDMA_CCR(id), STM32_MDMA_CCR_EN); |
| |
| /* Set SW request in case of MEM2MEM transfer */ |
| if (hwdesc->ctcr & STM32_MDMA_CTCR_SWRM) { |
| reg = STM32_MDMA_CCR(id); |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CCR_SWRQ); |
| } |
| |
| chan->busy = true; |
| |
| dev_dbg(chan2dev(chan), "vchan %pK: started\n", &chan->vchan); |
| } |
| |
| static void stm32_mdma_issue_pending(struct dma_chan *c) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| |
| if (!vchan_issue_pending(&chan->vchan)) |
| goto end; |
| |
| dev_dbg(chan2dev(chan), "vchan %pK: issued\n", &chan->vchan); |
| |
| if (!chan->desc && !chan->busy) |
| stm32_mdma_start_transfer(chan); |
| |
| end: |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| } |
| |
| static int stm32_mdma_pause(struct dma_chan *c) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| unsigned long flags; |
| int ret; |
| |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| ret = stm32_mdma_disable_chan(chan); |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| |
| if (!ret) |
| dev_dbg(chan2dev(chan), "vchan %pK: pause\n", &chan->vchan); |
| |
| return ret; |
| } |
| |
| static int stm32_mdma_resume(struct dma_chan *c) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| struct stm32_mdma_hwdesc *hwdesc; |
| unsigned long flags; |
| u32 status, reg; |
| |
| hwdesc = chan->desc->node[chan->curr_hwdesc].hwdesc; |
| |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| |
| /* Re-configure control register */ |
| stm32_mdma_write(dmadev, STM32_MDMA_CCR(chan->id), chan->desc->ccr); |
| |
| /* Clear interrupt status if it is there */ |
| status = stm32_mdma_read(dmadev, STM32_MDMA_CISR(chan->id)); |
| if (status) |
| stm32_mdma_set_bits(dmadev, STM32_MDMA_CIFCR(chan->id), status); |
| |
| stm32_mdma_dump_reg(chan); |
| |
| /* Re-start DMA */ |
| reg = STM32_MDMA_CCR(chan->id); |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CCR_EN); |
| |
| /* Set SW request in case of MEM2MEM transfer */ |
| if (hwdesc->ctcr & STM32_MDMA_CTCR_SWRM) |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CCR_SWRQ); |
| |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| |
| dev_dbg(chan2dev(chan), "vchan %pK: resume\n", &chan->vchan); |
| |
| return 0; |
| } |
| |
| static int stm32_mdma_terminate_all(struct dma_chan *c) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| unsigned long flags; |
| LIST_HEAD(head); |
| |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| if (chan->desc) { |
| vchan_terminate_vdesc(&chan->desc->vdesc); |
| if (chan->busy) |
| stm32_mdma_stop(chan); |
| chan->desc = NULL; |
| } |
| vchan_get_all_descriptors(&chan->vchan, &head); |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| |
| vchan_dma_desc_free_list(&chan->vchan, &head); |
| |
| return 0; |
| } |
| |
| static void stm32_mdma_synchronize(struct dma_chan *c) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| |
| vchan_synchronize(&chan->vchan); |
| } |
| |
| static int stm32_mdma_slave_config(struct dma_chan *c, |
| struct dma_slave_config *config) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| |
| memcpy(&chan->dma_config, config, sizeof(*config)); |
| |
| /* Check if user is requesting STM32 DMA to trigger MDMA */ |
| if (config->peripheral_size) { |
| struct stm32_mdma_dma_config *mdma_config; |
| |
| mdma_config = (struct stm32_mdma_dma_config *)chan->dma_config.peripheral_config; |
| chan->chan_config.request = mdma_config->request; |
| chan->chan_config.mask_addr = mdma_config->cmar; |
| chan->chan_config.mask_data = mdma_config->cmdr; |
| chan->chan_config.m2m_hw = true; |
| } |
| |
| return 0; |
| } |
| |
| static size_t stm32_mdma_desc_residue(struct stm32_mdma_chan *chan, |
| struct stm32_mdma_desc *desc, |
| u32 curr_hwdesc) |
| { |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| struct stm32_mdma_hwdesc *hwdesc; |
| u32 cbndtr, residue, modulo, burst_size; |
| int i; |
| |
| residue = 0; |
| for (i = curr_hwdesc + 1; i < desc->count; i++) { |
| hwdesc = desc->node[i].hwdesc; |
| residue += STM32_MDMA_CBNDTR_BNDT(hwdesc->cbndtr); |
| } |
| cbndtr = stm32_mdma_read(dmadev, STM32_MDMA_CBNDTR(chan->id)); |
| residue += cbndtr & STM32_MDMA_CBNDTR_BNDT_MASK; |
| |
| if (!chan->mem_burst) |
| return residue; |
| |
| burst_size = chan->mem_burst * chan->mem_width; |
| modulo = residue % burst_size; |
| if (modulo) |
| residue = residue - modulo + burst_size; |
| |
| return residue; |
| } |
| |
| static enum dma_status stm32_mdma_tx_status(struct dma_chan *c, |
| dma_cookie_t cookie, |
| struct dma_tx_state *state) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct virt_dma_desc *vdesc; |
| enum dma_status status; |
| unsigned long flags; |
| u32 residue = 0; |
| |
| status = dma_cookie_status(c, cookie, state); |
| if ((status == DMA_COMPLETE) || (!state)) |
| return status; |
| |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| |
| vdesc = vchan_find_desc(&chan->vchan, cookie); |
| if (chan->desc && cookie == chan->desc->vdesc.tx.cookie) |
| residue = stm32_mdma_desc_residue(chan, chan->desc, |
| chan->curr_hwdesc); |
| else if (vdesc) |
| residue = stm32_mdma_desc_residue(chan, |
| to_stm32_mdma_desc(vdesc), 0); |
| dma_set_residue(state, residue); |
| |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| |
| return status; |
| } |
| |
| static void stm32_mdma_xfer_end(struct stm32_mdma_chan *chan) |
| { |
| vchan_cookie_complete(&chan->desc->vdesc); |
| chan->desc = NULL; |
| chan->busy = false; |
| |
| /* Start the next transfer if this driver has a next desc */ |
| stm32_mdma_start_transfer(chan); |
| } |
| |
| static irqreturn_t stm32_mdma_irq_handler(int irq, void *devid) |
| { |
| struct stm32_mdma_device *dmadev = devid; |
| struct stm32_mdma_chan *chan; |
| u32 reg, id, ccr, ien, status; |
| |
| /* Find out which channel generates the interrupt */ |
| status = readl_relaxed(dmadev->base + STM32_MDMA_GISR0); |
| if (!status) { |
| dev_dbg(mdma2dev(dmadev), "spurious it\n"); |
| return IRQ_NONE; |
| } |
| id = __ffs(status); |
| chan = &dmadev->chan[id]; |
| |
| /* Handle interrupt for the channel */ |
| spin_lock(&chan->vchan.lock); |
| status = stm32_mdma_read(dmadev, STM32_MDMA_CISR(id)); |
| /* Mask Channel ReQuest Active bit which can be set in case of MEM2MEM */ |
| status &= ~STM32_MDMA_CISR_CRQA; |
| ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(id)); |
| ien = (ccr & STM32_MDMA_CCR_IRQ_MASK) >> 1; |
| |
| if (!(status & ien)) { |
| spin_unlock(&chan->vchan.lock); |
| if (chan->busy) |
| dev_warn(chan2dev(chan), |
| "spurious it (status=0x%04x, ien=0x%04x)\n", status, ien); |
| else |
| dev_dbg(chan2dev(chan), |
| "spurious it (status=0x%04x, ien=0x%04x)\n", status, ien); |
| return IRQ_NONE; |
| } |
| |
| reg = STM32_MDMA_CIFCR(id); |
| |
| if (status & STM32_MDMA_CISR_TEIF) { |
| dev_err(chan2dev(chan), "Transfer Err: stat=0x%08x\n", |
| readl_relaxed(dmadev->base + STM32_MDMA_CESR(id))); |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CIFCR_CTEIF); |
| status &= ~STM32_MDMA_CISR_TEIF; |
| } |
| |
| if (status & STM32_MDMA_CISR_CTCIF) { |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CIFCR_CCTCIF); |
| status &= ~STM32_MDMA_CISR_CTCIF; |
| stm32_mdma_xfer_end(chan); |
| } |
| |
| if (status & STM32_MDMA_CISR_BRTIF) { |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CIFCR_CBRTIF); |
| status &= ~STM32_MDMA_CISR_BRTIF; |
| } |
| |
| if (status & STM32_MDMA_CISR_BTIF) { |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CIFCR_CBTIF); |
| status &= ~STM32_MDMA_CISR_BTIF; |
| chan->curr_hwdesc++; |
| if (chan->desc && chan->desc->cyclic) { |
| if (chan->curr_hwdesc == chan->desc->count) |
| chan->curr_hwdesc = 0; |
| vchan_cyclic_callback(&chan->desc->vdesc); |
| } |
| } |
| |
| if (status & STM32_MDMA_CISR_TCIF) { |
| stm32_mdma_set_bits(dmadev, reg, STM32_MDMA_CIFCR_CLTCIF); |
| status &= ~STM32_MDMA_CISR_TCIF; |
| } |
| |
| if (status) { |
| stm32_mdma_set_bits(dmadev, reg, status); |
| dev_err(chan2dev(chan), "DMA error: status=0x%08x\n", status); |
| if (!(ccr & STM32_MDMA_CCR_EN)) |
| dev_err(chan2dev(chan), "chan disabled by HW\n"); |
| } |
| |
| spin_unlock(&chan->vchan.lock); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int stm32_mdma_alloc_chan_resources(struct dma_chan *c) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| int ret; |
| |
| chan->desc_pool = dmam_pool_create(dev_name(&c->dev->device), |
| c->device->dev, |
| sizeof(struct stm32_mdma_hwdesc), |
| __alignof__(struct stm32_mdma_hwdesc), |
| 0); |
| if (!chan->desc_pool) { |
| dev_err(chan2dev(chan), "failed to allocate descriptor pool\n"); |
| return -ENOMEM; |
| } |
| |
| ret = pm_runtime_resume_and_get(dmadev->ddev.dev); |
| if (ret < 0) |
| return ret; |
| |
| ret = stm32_mdma_disable_chan(chan); |
| if (ret < 0) |
| pm_runtime_put(dmadev->ddev.dev); |
| |
| return ret; |
| } |
| |
| static void stm32_mdma_free_chan_resources(struct dma_chan *c) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| unsigned long flags; |
| |
| dev_dbg(chan2dev(chan), "Freeing channel %d\n", chan->id); |
| |
| if (chan->busy) { |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| stm32_mdma_stop(chan); |
| chan->desc = NULL; |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| } |
| |
| pm_runtime_put(dmadev->ddev.dev); |
| vchan_free_chan_resources(to_virt_chan(c)); |
| dmam_pool_destroy(chan->desc_pool); |
| chan->desc_pool = NULL; |
| } |
| |
| static bool stm32_mdma_filter_fn(struct dma_chan *c, void *fn_param) |
| { |
| struct stm32_mdma_chan *chan = to_stm32_mdma_chan(c); |
| struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan); |
| |
| /* Check if chan is marked Secure */ |
| if (dmadev->chan_reserved & BIT(chan->id)) |
| return false; |
| |
| return true; |
| } |
| |
| static struct dma_chan *stm32_mdma_of_xlate(struct of_phandle_args *dma_spec, |
| struct of_dma *ofdma) |
| { |
| struct stm32_mdma_device *dmadev = ofdma->of_dma_data; |
| dma_cap_mask_t mask = dmadev->ddev.cap_mask; |
| struct stm32_mdma_chan *chan; |
| struct dma_chan *c; |
| struct stm32_mdma_chan_config config; |
| |
| if (dma_spec->args_count < 5) { |
| dev_err(mdma2dev(dmadev), "Bad number of args\n"); |
| return NULL; |
| } |
| |
| config.request = dma_spec->args[0]; |
| config.priority_level = dma_spec->args[1]; |
| config.transfer_config = dma_spec->args[2]; |
| config.mask_addr = dma_spec->args[3]; |
| config.mask_data = dma_spec->args[4]; |
| |
| if (config.request >= dmadev->nr_requests) { |
| dev_err(mdma2dev(dmadev), "Bad request line\n"); |
| return NULL; |
| } |
| |
| if (config.priority_level > STM32_MDMA_VERY_HIGH_PRIORITY) { |
| dev_err(mdma2dev(dmadev), "Priority level not supported\n"); |
| return NULL; |
| } |
| |
| c = __dma_request_channel(&mask, stm32_mdma_filter_fn, &config, ofdma->of_node); |
| if (!c) { |
| dev_err(mdma2dev(dmadev), "No more channels available\n"); |
| return NULL; |
| } |
| |
| chan = to_stm32_mdma_chan(c); |
| chan->chan_config = config; |
| |
| return c; |
| } |
| |
| static const struct of_device_id stm32_mdma_of_match[] = { |
| { .compatible = "st,stm32h7-mdma", }, |
| { /* sentinel */ }, |
| }; |
| MODULE_DEVICE_TABLE(of, stm32_mdma_of_match); |
| |
| static int stm32_mdma_probe(struct platform_device *pdev) |
| { |
| struct stm32_mdma_chan *chan; |
| struct stm32_mdma_device *dmadev; |
| struct dma_device *dd; |
| struct device_node *of_node; |
| struct resource *res; |
| struct reset_control *rst; |
| u32 nr_channels, nr_requests; |
| int i, count, ret; |
| |
| of_node = pdev->dev.of_node; |
| if (!of_node) |
| return -ENODEV; |
| |
| ret = device_property_read_u32(&pdev->dev, "dma-channels", |
| &nr_channels); |
| if (ret) { |
| nr_channels = STM32_MDMA_MAX_CHANNELS; |
| dev_warn(&pdev->dev, "MDMA defaulting on %i channels\n", |
| nr_channels); |
| } |
| |
| ret = device_property_read_u32(&pdev->dev, "dma-requests", |
| &nr_requests); |
| if (ret) { |
| nr_requests = STM32_MDMA_MAX_REQUESTS; |
| dev_warn(&pdev->dev, "MDMA defaulting on %i request lines\n", |
| nr_requests); |
| } |
| |
| count = device_property_count_u32(&pdev->dev, "st,ahb-addr-masks"); |
| if (count < 0) |
| count = 0; |
| |
| dmadev = devm_kzalloc(&pdev->dev, |
| struct_size(dmadev, ahb_addr_masks, count), |
| GFP_KERNEL); |
| if (!dmadev) |
| return -ENOMEM; |
| |
| dmadev->nr_channels = nr_channels; |
| dmadev->nr_requests = nr_requests; |
| device_property_read_u32_array(&pdev->dev, "st,ahb-addr-masks", |
| dmadev->ahb_addr_masks, |
| count); |
| dmadev->nr_ahb_addr_masks = count; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| dmadev->base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(dmadev->base)) |
| return PTR_ERR(dmadev->base); |
| |
| dmadev->clk = devm_clk_get(&pdev->dev, NULL); |
| if (IS_ERR(dmadev->clk)) |
| return dev_err_probe(&pdev->dev, PTR_ERR(dmadev->clk), |
| "Missing clock controller\n"); |
| |
| ret = clk_prepare_enable(dmadev->clk); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "clk_prep_enable error: %d\n", ret); |
| return ret; |
| } |
| |
| rst = devm_reset_control_get(&pdev->dev, NULL); |
| if (IS_ERR(rst)) { |
| ret = PTR_ERR(rst); |
| if (ret == -EPROBE_DEFER) |
| goto err_clk; |
| } else { |
| reset_control_assert(rst); |
| udelay(2); |
| reset_control_deassert(rst); |
| } |
| |
| dd = &dmadev->ddev; |
| dma_cap_set(DMA_SLAVE, dd->cap_mask); |
| dma_cap_set(DMA_PRIVATE, dd->cap_mask); |
| dma_cap_set(DMA_CYCLIC, dd->cap_mask); |
| dma_cap_set(DMA_MEMCPY, dd->cap_mask); |
| dd->device_alloc_chan_resources = stm32_mdma_alloc_chan_resources; |
| dd->device_free_chan_resources = stm32_mdma_free_chan_resources; |
| dd->device_tx_status = stm32_mdma_tx_status; |
| dd->device_issue_pending = stm32_mdma_issue_pending; |
| dd->device_prep_slave_sg = stm32_mdma_prep_slave_sg; |
| dd->device_prep_dma_cyclic = stm32_mdma_prep_dma_cyclic; |
| dd->device_prep_dma_memcpy = stm32_mdma_prep_dma_memcpy; |
| dd->device_config = stm32_mdma_slave_config; |
| dd->device_pause = stm32_mdma_pause; |
| dd->device_resume = stm32_mdma_resume; |
| dd->device_terminate_all = stm32_mdma_terminate_all; |
| dd->device_synchronize = stm32_mdma_synchronize; |
| dd->descriptor_reuse = true; |
| |
| dd->src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) | |
| BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) | |
| BIT(DMA_SLAVE_BUSWIDTH_4_BYTES) | |
| BIT(DMA_SLAVE_BUSWIDTH_8_BYTES); |
| dd->dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) | |
| BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) | |
| BIT(DMA_SLAVE_BUSWIDTH_4_BYTES) | |
| BIT(DMA_SLAVE_BUSWIDTH_8_BYTES); |
| dd->directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV) | |
| BIT(DMA_MEM_TO_MEM); |
| dd->residue_granularity = DMA_RESIDUE_GRANULARITY_BURST; |
| dd->max_burst = STM32_MDMA_MAX_BURST; |
| dd->dev = &pdev->dev; |
| INIT_LIST_HEAD(&dd->channels); |
| |
| for (i = 0; i < dmadev->nr_channels; i++) { |
| chan = &dmadev->chan[i]; |
| chan->id = i; |
| |
| if (stm32_mdma_read(dmadev, STM32_MDMA_CCR(i)) & STM32_MDMA_CCR_SM) |
| dmadev->chan_reserved |= BIT(i); |
| |
| chan->vchan.desc_free = stm32_mdma_desc_free; |
| vchan_init(&chan->vchan, dd); |
| } |
| |
| dmadev->irq = platform_get_irq(pdev, 0); |
| if (dmadev->irq < 0) { |
| ret = dmadev->irq; |
| goto err_clk; |
| } |
| |
| ret = devm_request_irq(&pdev->dev, dmadev->irq, stm32_mdma_irq_handler, |
| 0, dev_name(&pdev->dev), dmadev); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to request IRQ\n"); |
| goto err_clk; |
| } |
| |
| ret = dmaenginem_async_device_register(dd); |
| if (ret) |
| goto err_clk; |
| |
| ret = of_dma_controller_register(of_node, stm32_mdma_of_xlate, dmadev); |
| if (ret < 0) { |
| dev_err(&pdev->dev, |
| "STM32 MDMA DMA OF registration failed %d\n", ret); |
| goto err_clk; |
| } |
| |
| platform_set_drvdata(pdev, dmadev); |
| pm_runtime_set_active(&pdev->dev); |
| pm_runtime_enable(&pdev->dev); |
| pm_runtime_get_noresume(&pdev->dev); |
| pm_runtime_put(&pdev->dev); |
| |
| dev_info(&pdev->dev, "STM32 MDMA driver registered\n"); |
| |
| return 0; |
| |
| err_clk: |
| clk_disable_unprepare(dmadev->clk); |
| |
| return ret; |
| } |
| |
| #ifdef CONFIG_PM |
| static int stm32_mdma_runtime_suspend(struct device *dev) |
| { |
| struct stm32_mdma_device *dmadev = dev_get_drvdata(dev); |
| |
| clk_disable_unprepare(dmadev->clk); |
| |
| return 0; |
| } |
| |
| static int stm32_mdma_runtime_resume(struct device *dev) |
| { |
| struct stm32_mdma_device *dmadev = dev_get_drvdata(dev); |
| int ret; |
| |
| ret = clk_prepare_enable(dmadev->clk); |
| if (ret) { |
| dev_err(dev, "failed to prepare_enable clock\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int stm32_mdma_pm_suspend(struct device *dev) |
| { |
| struct stm32_mdma_device *dmadev = dev_get_drvdata(dev); |
| u32 ccr, id; |
| int ret; |
| |
| ret = pm_runtime_resume_and_get(dev); |
| if (ret < 0) |
| return ret; |
| |
| for (id = 0; id < dmadev->nr_channels; id++) { |
| ccr = stm32_mdma_read(dmadev, STM32_MDMA_CCR(id)); |
| if (ccr & STM32_MDMA_CCR_EN) { |
| dev_warn(dev, "Suspend is prevented by Chan %i\n", id); |
| return -EBUSY; |
| } |
| } |
| |
| pm_runtime_put_sync(dev); |
| |
| pm_runtime_force_suspend(dev); |
| |
| return 0; |
| } |
| |
| static int stm32_mdma_pm_resume(struct device *dev) |
| { |
| return pm_runtime_force_resume(dev); |
| } |
| #endif |
| |
| static const struct dev_pm_ops stm32_mdma_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(stm32_mdma_pm_suspend, stm32_mdma_pm_resume) |
| SET_RUNTIME_PM_OPS(stm32_mdma_runtime_suspend, |
| stm32_mdma_runtime_resume, NULL) |
| }; |
| |
| static struct platform_driver stm32_mdma_driver = { |
| .probe = stm32_mdma_probe, |
| .driver = { |
| .name = "stm32-mdma", |
| .of_match_table = stm32_mdma_of_match, |
| .pm = &stm32_mdma_pm_ops, |
| }, |
| }; |
| |
| static int __init stm32_mdma_init(void) |
| { |
| return platform_driver_register(&stm32_mdma_driver); |
| } |
| |
| subsys_initcall(stm32_mdma_init); |
| |
| MODULE_DESCRIPTION("Driver for STM32 MDMA controller"); |
| MODULE_AUTHOR("M'boumba Cedric Madianga <cedric.madianga@gmail.com>"); |
| MODULE_AUTHOR("Pierre-Yves Mordret <pierre-yves.mordret@st.com>"); |
| MODULE_LICENSE("GPL v2"); |