| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2020, The Linux Foundation. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include <dt-bindings/sound/qcom,q6afe.h> |
| #include <dt-bindings/sound/qcom,q6asm.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include "sm8250.dtsi" |
| #include "pm8150.dtsi" |
| #include "pm8150b.dtsi" |
| #include "pm8150l.dtsi" |
| #include "pm8009.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. SM8250 MTP"; |
| compatible = "qcom,sm8250-mtp", "qcom,sm8250"; |
| chassis-type = "handset"; |
| |
| aliases { |
| serial0 = &uart12; |
| }; |
| |
| wcd938x: audio-codec { |
| compatible = "qcom,wcd9380-codec"; |
| |
| reset-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; |
| |
| vdd-buck-supply = <&vreg_s4a_1p8>; |
| vdd-rxtx-supply = <&vreg_s4a_1p8>; |
| vdd-io-supply = <&vreg_s4a_1p8>; |
| vdd-mic-bias-supply = <&vreg_bob>; |
| |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| qcom,rx-device = <&wcd_rx>; |
| qcom,tx-device = <&wcd_tx>; |
| |
| #sound-dai-cells = <1>; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| thermal-zones { |
| camera-thermal { |
| thermal-sensors = <&pm8150l_adc_tm 0>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| conn-thermal { |
| thermal-sensors = <&pm8150b_adc_tm 0>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| mmw-pa1-thermal { |
| thermal-sensors = <&pm8150_adc_tm 2>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| mmw-pa2-thermal { |
| thermal-sensors = <&pm8150l_adc_tm 2>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| skin-msm-thermal { |
| thermal-sensors = <&pm8150l_adc_tm 1>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| skin-thermal { |
| thermal-sensors = <&pm8150_adc_tm 1>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| xo-thermal { |
| thermal-sensors = <&pm8150_adc_tm 0>; |
| |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| |
| vreg_s4a_1p8: pm8150-s4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_s4a_1p8"; |
| |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| |
| vin-supply = <&vph_pwr>; |
| }; |
| |
| vreg_s6c_0p88: smpc6-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_s6c_0p88"; |
| |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-always-on; |
| vin-supply = <&vph_pwr>; |
| }; |
| }; |
| |
| &adsp { |
| status = "okay"; |
| firmware-name = "qcom/sm8250/adsp.mbn"; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8150-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-s9-supply = <&vph_pwr>; |
| vdd-s10-supply = <&vph_pwr>; |
| vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>; |
| vdd-l2-l10-supply = <&vreg_bob>; |
| vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>; |
| vdd-l6-l9-supply = <&vreg_s8c_1p3>; |
| vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; |
| vdd-l13-l16-l17-supply = <&vreg_bob>; |
| |
| vreg_s5a_1p9: smps5 { |
| regulator-name = "vreg_s5a_1p9"; |
| regulator-min-microvolt = <1904000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s6a_0p95: smps6 { |
| regulator-name = "vreg_s6a_0p95"; |
| regulator-min-microvolt = <920000>; |
| regulator-max-microvolt = <1128000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2a_3p1: ldo2 { |
| regulator-name = "vreg_l2a_3p1"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3a_0p9: ldo3 { |
| regulator-name = "vreg_l3a_0p9"; |
| regulator-min-microvolt = <928000>; |
| regulator-max-microvolt = <932000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5a_0p875: ldo5 { |
| regulator-name = "vreg_l5a_0p875"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6a_1p2: ldo6 { |
| regulator-name = "vreg_l6a_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7a_1p7: ldo7 { |
| regulator-name = "vreg_l7a_1p7"; |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9a_1p2: ldo9 { |
| regulator-name = "vreg_l9a_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10a_1p8: ldo10 { |
| regulator-name = "vreg_l10a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12a_1p8: ldo12 { |
| regulator-name = "vreg_l12a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13a_ts_3p0: ldo13 { |
| regulator-name = "vreg_l13a_ts_3p0"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14a_1p8: ldo14 { |
| regulator-name = "vreg_l14a_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15a_11ad_io_1p8: ldo15 { |
| regulator-name = "vreg_l15a_11ad_io_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16a_2p7: ldo16 { |
| regulator-name = "vreg_l16a_2p7"; |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17a_3p0: ldo17 { |
| regulator-name = "vreg_l17a_3p0"; |
| regulator-min-microvolt = <2856000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l18a_0p9: ldo18 { |
| regulator-name = "vreg_l18a_0p9"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8150l-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-l1-l8-supply = <&vreg_s4a_1p8>; |
| vdd-l2-l3-supply = <&vreg_s8c_1p3>; |
| vdd-l4-l5-l6-supply = <&vreg_bob>; |
| vdd-l7-l11-supply = <&vreg_bob>; |
| vdd-l9-l10-supply = <&vreg_bob>; |
| vdd-bob-supply = <&vph_pwr>; |
| |
| vreg_bob: bob { |
| regulator-name = "vreg_bob"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <4000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; |
| }; |
| |
| vreg_s8c_1p3: smps8 { |
| regulator-name = "vreg_s8c_1p3"; |
| regulator-min-microvolt = <1352000>; |
| regulator-max-microvolt = <1352000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1c_1p8: ldo1 { |
| regulator-name = "vreg_l1c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2c_1p2: ldo2 { |
| regulator-name = "vreg_l2c_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c_0p92: ldo3 { |
| regulator-name = "vreg_l3c_0p92"; |
| regulator-min-microvolt = <920000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4c_1p7: ldo4 { |
| regulator-name = "vreg_l4c_1p7"; |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5c_1p8: ldo5 { |
| regulator-name = "vreg_l5c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6c_2p9: ldo6 { |
| regulator-name = "vreg_l6c_2p9"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7c_cam_vcm0_2p85: ldo7 { |
| regulator-name = "vreg_l7c_cam_vcm0_2p85"; |
| regulator-min-microvolt = <2856000>; |
| regulator-max-microvolt = <3104000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8c_1p8: ldo8 { |
| regulator-name = "vreg_l8c_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9c_2p9: ldo9 { |
| regulator-name = "vreg_l9c_2p9"; |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10c_3p0: ldo10 { |
| regulator-name = "vreg_l10c_3p0"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11c_3p3: ldo11 { |
| regulator-name = "vreg_l11c_3p3"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pm8009-rpmh-regulators"; |
| qcom,pmic-id = "f"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vreg_bob>; |
| vdd-l2-supply = <&vreg_s8c_1p3>; |
| vdd-l5-l6-supply = <&vreg_bob>; |
| vdd-l7-supply = <&vreg_s4a_1p8>; |
| |
| vreg_l1f_cam_dvdd1_1p1: ldo1 { |
| regulator-name = "vreg_l1f_cam_dvdd1_1p1"; |
| regulator-min-microvolt = <1104000>; |
| regulator-max-microvolt = <1104000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2f_cam_dvdd0_1p2: ldo2 { |
| regulator-name = "vreg_l2f_cam_dvdd0_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3f_cam_dvdd2_1p05: ldo3 { |
| regulator-name = "vreg_l3f_cam_dvdd2_1p05"; |
| regulator-min-microvolt = <1056000>; |
| regulator-max-microvolt = <1056000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5f_cam_avdd0_2p85: ldo5 { |
| regulator-name = "vreg_l5f_cam_avdd0_2p85"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6f_cam_avdd1_2p85: ldo6 { |
| regulator-name = "vreg_l6f_cam_avdd1_2p85"; |
| regulator-min-microvolt = <2856000>; |
| regulator-max-microvolt = <2856000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7f_1p8: ldo7 { |
| regulator-name = "vreg_l7f_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &cdsp { |
| status = "okay"; |
| firmware-name = "qcom/sm8250/cdsp.mbn"; |
| }; |
| |
| &gmu { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| firmware-name = "qcom/sm8250/a650_zap.mbn"; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| clock-frequency = <1000000>; |
| |
| /* NQ NFC chip @28 */ |
| }; |
| |
| &i2c13 { |
| status = "okay"; |
| |
| /* st,stmfts @ 49 */ |
| }; |
| |
| &i2c15 { |
| status = "okay"; |
| |
| /* smb1390 @ 10 */ |
| /* rtc6226 @ 64 */ |
| }; |
| |
| &pm8150_adc { |
| channel@4c { |
| reg = <ADC5_XO_THERM_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "xo_therm"; |
| }; |
| |
| channel@4d { |
| reg = <ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "skin_therm"; |
| }; |
| |
| channel@4e { |
| reg = <ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "pa_therm1"; |
| }; |
| }; |
| |
| &pm8150_adc_tm { |
| status = "okay"; |
| |
| xo-therm@0 { |
| reg = <0>; |
| io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| skin-therm@1 { |
| reg = <1>; |
| io-channels = <&pm8150_adc ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| pa-therm1@2 { |
| reg = <2>; |
| io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| |
| &pm8150b_adc { |
| channel@4f { |
| reg = <ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "conn_therm"; |
| }; |
| }; |
| |
| &pm8150b_adc_tm { |
| status = "okay"; |
| |
| conn-therm@0 { |
| reg = <0>; |
| io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| |
| &pm8150l_adc_tm { |
| status = "okay"; |
| |
| camera-flash-therm@0 { |
| reg = <0>; |
| io-channels = <&pm8150l_adc ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| skin-msm-therm@1 { |
| reg = <1>; |
| io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| |
| pa-therm2@2 { |
| reg = <2>; |
| io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time-us = <200>; |
| }; |
| }; |
| |
| &pm8150l_adc { |
| channel@4d { |
| reg = <ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "camera_flash_therm"; |
| }; |
| |
| channel@4e { |
| reg = <ADC5_AMUX_THM2_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "skin_msm_therm"; |
| }; |
| |
| channel@4f { |
| reg = <ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| label = "pa_therm2"; |
| }; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_2 { |
| status = "okay"; |
| }; |
| |
| &rxmacro { |
| status = "okay"; |
| }; |
| |
| &slpi { |
| status = "okay"; |
| firmware-name = "qcom/sm8250/slpi.mbn"; |
| }; |
| |
| &sound { |
| compatible = "qcom,sm8250-sndcard"; |
| model = "SM8250-MTP-WCD9380-WSA8810-VA-DMIC"; |
| audio-routing = |
| "SpkrLeft IN", "WSA_SPK1 OUT", |
| "SpkrRight IN", "WSA_SPK2 OUT", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "AMIC1", "MIC BIAS1", |
| "AMIC2", "MIC BIAS2", |
| "AMIC3", "MIC BIAS3", |
| "AMIC4", "MIC BIAS3", |
| "AMIC5", "MIC BIAS4", |
| "TX SWR_ADC0", "ADC1_OUTPUT", |
| "TX SWR_ADC1", "ADC2_OUTPUT", |
| "TX SWR_ADC2", "ADC3_OUTPUT", |
| "TX SWR_ADC3", "ADC4_OUTPUT", |
| "TX SWR_DMIC0", "DMIC1_OUTPUT", |
| "TX SWR_DMIC1", "DMIC2_OUTPUT", |
| "TX SWR_DMIC2", "DMIC3_OUTPUT", |
| "TX SWR_DMIC3", "DMIC4_OUTPUT", |
| "TX SWR_DMIC4", "DMIC5_OUTPUT", |
| "TX SWR_DMIC5", "DMIC6_OUTPUT", |
| "TX SWR_DMIC6", "DMIC7_OUTPUT", |
| "TX SWR_DMIC7", "DMIC8_OUTPUT"; |
| |
| mm1-dai-link { |
| link-name = "MultiMedia1"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| }; |
| }; |
| |
| mm2-dai-link { |
| link-name = "MultiMedia2"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; |
| }; |
| }; |
| |
| mm3-dai-link { |
| link-name = "MultiMedia3"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; |
| }; |
| }; |
| |
| wcd-playback-dai-link { |
| link-name = "WCD Playback"; |
| cpu { |
| sound-dai = <&q6afedai RX_CODEC_DMA_RX_0>; |
| }; |
| codec { |
| sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>; |
| }; |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| |
| wcd-capture-dai-link { |
| link-name = "WCD Capture"; |
| cpu { |
| sound-dai = <&q6afedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>; |
| }; |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| |
| wsa-dai-link { |
| link-name = "WSA Playback"; |
| cpu { |
| sound-dai = <&q6afedai WSA_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; |
| }; |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| }; |
| |
| va-dai-link { |
| link-name = "VA Capture"; |
| cpu { |
| sound-dai = <&q6afedai VA_CODEC_DMA_TX_0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&vamacro 0>; |
| }; |
| }; |
| }; |
| |
| &swr0 { |
| status = "okay"; |
| |
| left_spkr: speaker@0,3 { |
| compatible = "sdw10217211000"; |
| reg = <0 3>; |
| powerdown-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>; |
| #thermal-sensor-cells = <0>; |
| sound-name-prefix = "SpkrLeft"; |
| #sound-dai-cells = <0>; |
| }; |
| |
| right_spkr: speaker@0,4 { |
| compatible = "sdw10217211000"; |
| reg = <0 4>; |
| powerdown-gpios = <&tlmm 127 GPIO_ACTIVE_LOW>; |
| #thermal-sensor-cells = <0>; |
| sound-name-prefix = "SpkrRight"; |
| #sound-dai-cells = <0>; |
| }; |
| }; |
| |
| &swr1 { |
| status = "okay"; |
| |
| wcd_rx: wcd9380-rx@0,4 { |
| compatible = "sdw20217010d00"; |
| reg = <0 4>; |
| qcom,rx-port-mapping = <1 2 3 4 5>; |
| }; |
| }; |
| |
| &swr2 { |
| status = "okay"; |
| |
| wcd_tx: wcd9380-tx@0,3 { |
| compatible = "sdw20217010d00"; |
| reg = <0 3>; |
| qcom,tx-port-mapping = <2 3 4 5>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <28 4>, <40 4>; |
| |
| wcd938x_reset_default: wcd938x-reset-default-state { |
| pins = "gpio32"; |
| function = "gpio"; |
| drive-strength = <16>; |
| output-high; |
| }; |
| |
| wcd938x_reset_sleep: wcd938x-reset-sleep-state { |
| pins = "gpio32"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| &txmacro { |
| status = "okay"; |
| }; |
| |
| &uart12 { |
| status = "okay"; |
| }; |
| |
| &ufs_mem_hc { |
| status = "okay"; |
| |
| vcc-supply = <&vreg_l17a_3p0>; |
| vcc-max-microamp = <750000>; |
| vccq-supply = <&vreg_l6a_1p2>; |
| vccq-max-microamp = <700000>; |
| vccq2-supply = <&vreg_s4a_1p8>; |
| vccq2-max-microamp = <750000>; |
| }; |
| |
| &ufs_mem_phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l5a_0p875>; |
| vdda-pll-supply = <&vreg_l9a_1p2>; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_hsphy { |
| status = "okay"; |
| |
| vdda-pll-supply = <&vreg_l5a_0p875>; |
| vdda18-supply = <&vreg_l12a_1p8>; |
| vdda33-supply = <&vreg_l2a_3p1>; |
| }; |
| |
| &usb_1_qmpphy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l9a_1p2>; |
| vdda-pll-supply = <&vreg_l18a_0p9>; |
| }; |
| |
| &usb_2 { |
| status = "okay"; |
| }; |
| |
| &usb_2_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_2_hsphy { |
| status = "okay"; |
| |
| vdda-pll-supply = <&vreg_l5a_0p875>; |
| vdda18-supply = <&vreg_l12a_1p8>; |
| vdda33-supply = <&vreg_l2a_3p1>; |
| }; |
| |
| &usb_2_qmpphy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vreg_l9a_1p2>; |
| vdda-pll-supply = <&vreg_l18a_0p9>; |
| }; |
| |
| &venus { |
| status = "okay"; |
| }; |
| |
| &wsamacro { |
| status = "okay"; |
| }; |
