| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Afatech AF9033 demodulator driver |
| * |
| * Copyright (C) 2009 Antti Palosaari <crope@iki.fi> |
| * Copyright (C) 2012 Antti Palosaari <crope@iki.fi> |
| */ |
| |
| #include "af9033_priv.h" |
| |
| struct af9033_dev { |
| struct i2c_client *client; |
| struct regmap *regmap; |
| struct dvb_frontend fe; |
| struct af9033_config cfg; |
| bool is_af9035; |
| bool is_it9135; |
| |
| u32 bandwidth_hz; |
| bool ts_mode_parallel; |
| bool ts_mode_serial; |
| |
| enum fe_status fe_status; |
| u64 post_bit_error_prev; /* for old read_ber we return (curr - prev) */ |
| u64 post_bit_error; |
| u64 post_bit_count; |
| u64 error_block_count; |
| u64 total_block_count; |
| }; |
| |
| /* Write reg val table using reg addr auto increment */ |
| static int af9033_wr_reg_val_tab(struct af9033_dev *dev, |
| const struct reg_val *tab, int tab_len) |
| { |
| struct i2c_client *client = dev->client; |
| #define MAX_TAB_LEN 212 |
| int ret, i, j; |
| u8 buf[1 + MAX_TAB_LEN]; |
| |
| dev_dbg(&client->dev, "tab_len=%d\n", tab_len); |
| |
| if (tab_len > sizeof(buf)) { |
| dev_warn(&client->dev, "tab len %d is too big\n", tab_len); |
| return -EINVAL; |
| } |
| |
| for (i = 0, j = 0; i < tab_len; i++) { |
| buf[j] = tab[i].val; |
| |
| if (i == tab_len - 1 || tab[i].reg != tab[i + 1].reg - 1) { |
| ret = regmap_bulk_write(dev->regmap, tab[i].reg - j, |
| buf, j + 1); |
| if (ret) |
| goto err; |
| |
| j = 0; |
| } else { |
| j++; |
| } |
| } |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_init(struct dvb_frontend *fe) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret, i, len; |
| unsigned int utmp; |
| const struct reg_val *init; |
| u8 buf[4]; |
| struct reg_val_mask tab[] = { |
| { 0x80fb24, 0x00, 0x08 }, |
| { 0x80004c, 0x00, 0xff }, |
| { 0x00f641, dev->cfg.tuner, 0xff }, |
| { 0x80f5ca, 0x01, 0x01 }, |
| { 0x80f715, 0x01, 0x01 }, |
| { 0x00f41f, 0x04, 0x04 }, |
| { 0x00f41a, 0x01, 0x01 }, |
| { 0x80f731, 0x00, 0x01 }, |
| { 0x00d91e, 0x00, 0x01 }, |
| { 0x00d919, 0x00, 0x01 }, |
| { 0x80f732, 0x00, 0x01 }, |
| { 0x00d91f, 0x00, 0x01 }, |
| { 0x00d91a, 0x00, 0x01 }, |
| { 0x80f730, 0x00, 0x01 }, |
| { 0x80f778, 0x00, 0xff }, |
| { 0x80f73c, 0x01, 0x01 }, |
| { 0x80f776, 0x00, 0x01 }, |
| { 0x00d8fd, 0x01, 0xff }, |
| { 0x00d830, 0x01, 0xff }, |
| { 0x00d831, 0x00, 0xff }, |
| { 0x00d832, 0x00, 0xff }, |
| { 0x80f985, dev->ts_mode_serial, 0x01 }, |
| { 0x80f986, dev->ts_mode_parallel, 0x01 }, |
| { 0x00d827, 0x00, 0xff }, |
| { 0x00d829, 0x00, 0xff }, |
| { 0x800045, dev->cfg.adc_multiplier, 0xff }, |
| }; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| /* Main clk control */ |
| utmp = div_u64((u64)dev->cfg.clock * 0x80000, 1000000); |
| buf[0] = (utmp >> 0) & 0xff; |
| buf[1] = (utmp >> 8) & 0xff; |
| buf[2] = (utmp >> 16) & 0xff; |
| buf[3] = (utmp >> 24) & 0xff; |
| ret = regmap_bulk_write(dev->regmap, 0x800025, buf, 4); |
| if (ret) |
| goto err; |
| |
| dev_dbg(&client->dev, "clk=%u clk_cw=%08x\n", dev->cfg.clock, utmp); |
| |
| /* ADC clk control */ |
| for (i = 0; i < ARRAY_SIZE(clock_adc_lut); i++) { |
| if (clock_adc_lut[i].clock == dev->cfg.clock) |
| break; |
| } |
| if (i == ARRAY_SIZE(clock_adc_lut)) { |
| dev_err(&client->dev, "Couldn't find ADC config for clock %d\n", |
| dev->cfg.clock); |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| utmp = div_u64((u64)clock_adc_lut[i].adc * 0x80000, 1000000); |
| buf[0] = (utmp >> 0) & 0xff; |
| buf[1] = (utmp >> 8) & 0xff; |
| buf[2] = (utmp >> 16) & 0xff; |
| ret = regmap_bulk_write(dev->regmap, 0x80f1cd, buf, 3); |
| if (ret) |
| goto err; |
| |
| dev_dbg(&client->dev, "adc=%u adc_cw=%06x\n", |
| clock_adc_lut[i].adc, utmp); |
| |
| /* Config register table */ |
| for (i = 0; i < ARRAY_SIZE(tab); i++) { |
| ret = regmap_update_bits(dev->regmap, tab[i].reg, tab[i].mask, |
| tab[i].val); |
| if (ret) |
| goto err; |
| } |
| |
| /* Demod clk output */ |
| if (dev->cfg.dyn0_clk) { |
| ret = regmap_write(dev->regmap, 0x80fba8, 0x00); |
| if (ret) |
| goto err; |
| } |
| |
| /* TS interface */ |
| if (dev->cfg.ts_mode == AF9033_TS_MODE_USB) { |
| ret = regmap_update_bits(dev->regmap, 0x80f9a5, 0x01, 0x00); |
| if (ret) |
| goto err; |
| ret = regmap_update_bits(dev->regmap, 0x80f9b5, 0x01, 0x01); |
| if (ret) |
| goto err; |
| } else { |
| ret = regmap_update_bits(dev->regmap, 0x80f990, 0x01, 0x00); |
| if (ret) |
| goto err; |
| ret = regmap_update_bits(dev->regmap, 0x80f9b5, 0x01, 0x00); |
| if (ret) |
| goto err; |
| } |
| |
| /* Demod core settings */ |
| dev_dbg(&client->dev, "load ofsm settings\n"); |
| switch (dev->cfg.tuner) { |
| case AF9033_TUNER_IT9135_38: |
| case AF9033_TUNER_IT9135_51: |
| case AF9033_TUNER_IT9135_52: |
| len = ARRAY_SIZE(ofsm_init_it9135_v1); |
| init = ofsm_init_it9135_v1; |
| break; |
| case AF9033_TUNER_IT9135_60: |
| case AF9033_TUNER_IT9135_61: |
| case AF9033_TUNER_IT9135_62: |
| len = ARRAY_SIZE(ofsm_init_it9135_v2); |
| init = ofsm_init_it9135_v2; |
| break; |
| default: |
| len = ARRAY_SIZE(ofsm_init); |
| init = ofsm_init; |
| break; |
| } |
| |
| ret = af9033_wr_reg_val_tab(dev, init, len); |
| if (ret) |
| goto err; |
| |
| /* Demod tuner specific settings */ |
| dev_dbg(&client->dev, "load tuner specific settings\n"); |
| switch (dev->cfg.tuner) { |
| case AF9033_TUNER_TUA9001: |
| len = ARRAY_SIZE(tuner_init_tua9001); |
| init = tuner_init_tua9001; |
| break; |
| case AF9033_TUNER_FC0011: |
| len = ARRAY_SIZE(tuner_init_fc0011); |
| init = tuner_init_fc0011; |
| break; |
| case AF9033_TUNER_MXL5007T: |
| len = ARRAY_SIZE(tuner_init_mxl5007t); |
| init = tuner_init_mxl5007t; |
| break; |
| case AF9033_TUNER_TDA18218: |
| len = ARRAY_SIZE(tuner_init_tda18218); |
| init = tuner_init_tda18218; |
| break; |
| case AF9033_TUNER_FC2580: |
| len = ARRAY_SIZE(tuner_init_fc2580); |
| init = tuner_init_fc2580; |
| break; |
| case AF9033_TUNER_FC0012: |
| len = ARRAY_SIZE(tuner_init_fc0012); |
| init = tuner_init_fc0012; |
| break; |
| case AF9033_TUNER_IT9135_38: |
| len = ARRAY_SIZE(tuner_init_it9135_38); |
| init = tuner_init_it9135_38; |
| break; |
| case AF9033_TUNER_IT9135_51: |
| len = ARRAY_SIZE(tuner_init_it9135_51); |
| init = tuner_init_it9135_51; |
| break; |
| case AF9033_TUNER_IT9135_52: |
| len = ARRAY_SIZE(tuner_init_it9135_52); |
| init = tuner_init_it9135_52; |
| break; |
| case AF9033_TUNER_IT9135_60: |
| len = ARRAY_SIZE(tuner_init_it9135_60); |
| init = tuner_init_it9135_60; |
| break; |
| case AF9033_TUNER_IT9135_61: |
| len = ARRAY_SIZE(tuner_init_it9135_61); |
| init = tuner_init_it9135_61; |
| break; |
| case AF9033_TUNER_IT9135_62: |
| len = ARRAY_SIZE(tuner_init_it9135_62); |
| init = tuner_init_it9135_62; |
| break; |
| default: |
| dev_dbg(&client->dev, "unsupported tuner ID=%d\n", |
| dev->cfg.tuner); |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| ret = af9033_wr_reg_val_tab(dev, init, len); |
| if (ret) |
| goto err; |
| |
| if (dev->cfg.ts_mode == AF9033_TS_MODE_SERIAL) { |
| ret = regmap_update_bits(dev->regmap, 0x00d91c, 0x01, 0x01); |
| if (ret) |
| goto err; |
| ret = regmap_update_bits(dev->regmap, 0x00d917, 0x01, 0x00); |
| if (ret) |
| goto err; |
| ret = regmap_update_bits(dev->regmap, 0x00d916, 0x01, 0x00); |
| if (ret) |
| goto err; |
| } |
| |
| switch (dev->cfg.tuner) { |
| case AF9033_TUNER_IT9135_60: |
| case AF9033_TUNER_IT9135_61: |
| case AF9033_TUNER_IT9135_62: |
| ret = regmap_write(dev->regmap, 0x800000, 0x01); |
| if (ret) |
| goto err; |
| } |
| |
| dev->bandwidth_hz = 0; /* Force to program all parameters */ |
| /* Init stats here in order signal app which stats are supported */ |
| c->strength.len = 1; |
| c->strength.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->cnr.len = 1; |
| c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->block_count.len = 1; |
| c->block_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->block_error.len = 1; |
| c->block_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->post_bit_count.len = 1; |
| c->post_bit_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->post_bit_error.len = 1; |
| c->post_bit_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_sleep(struct dvb_frontend *fe) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| int ret; |
| unsigned int utmp; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| ret = regmap_write(dev->regmap, 0x80004c, 0x01); |
| if (ret) |
| goto err; |
| ret = regmap_write(dev->regmap, 0x800000, 0x00); |
| if (ret) |
| goto err; |
| ret = regmap_read_poll_timeout(dev->regmap, 0x80004c, utmp, utmp == 0, |
| 5000, 1000000); |
| if (ret) |
| goto err; |
| ret = regmap_update_bits(dev->regmap, 0x80fb24, 0x08, 0x08); |
| if (ret) |
| goto err; |
| |
| /* Prevent current leak by setting TS interface to parallel mode */ |
| if (dev->cfg.ts_mode == AF9033_TS_MODE_SERIAL) { |
| /* Enable parallel TS */ |
| ret = regmap_update_bits(dev->regmap, 0x00d917, 0x01, 0x00); |
| if (ret) |
| goto err; |
| ret = regmap_update_bits(dev->regmap, 0x00d916, 0x01, 0x01); |
| if (ret) |
| goto err; |
| } |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_get_tune_settings(struct dvb_frontend *fe, |
| struct dvb_frontend_tune_settings *fesettings) |
| { |
| /* 800 => 2000 because IT9135 v2 is slow to gain lock */ |
| fesettings->min_delay_ms = 2000; |
| fesettings->step_size = 0; |
| fesettings->max_drift = 0; |
| |
| return 0; |
| } |
| |
| static int af9033_set_frontend(struct dvb_frontend *fe) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret, i; |
| unsigned int utmp, adc_freq; |
| u8 tmp, buf[3], bandwidth_reg_val; |
| u32 if_frequency; |
| |
| dev_dbg(&client->dev, "frequency=%u bandwidth_hz=%u\n", |
| c->frequency, c->bandwidth_hz); |
| |
| /* Check bandwidth */ |
| switch (c->bandwidth_hz) { |
| case 6000000: |
| bandwidth_reg_val = 0x00; |
| break; |
| case 7000000: |
| bandwidth_reg_val = 0x01; |
| break; |
| case 8000000: |
| bandwidth_reg_val = 0x02; |
| break; |
| default: |
| dev_dbg(&client->dev, "invalid bandwidth_hz\n"); |
| ret = -EINVAL; |
| goto err; |
| } |
| |
| /* Program tuner */ |
| if (fe->ops.tuner_ops.set_params) |
| fe->ops.tuner_ops.set_params(fe); |
| |
| /* Coefficients */ |
| if (c->bandwidth_hz != dev->bandwidth_hz) { |
| for (i = 0; i < ARRAY_SIZE(coeff_lut); i++) { |
| if (coeff_lut[i].clock == dev->cfg.clock && |
| coeff_lut[i].bandwidth_hz == c->bandwidth_hz) { |
| break; |
| } |
| } |
| if (i == ARRAY_SIZE(coeff_lut)) { |
| dev_err(&client->dev, |
| "Couldn't find config for clock %u\n", |
| dev->cfg.clock); |
| ret = -EINVAL; |
| goto err; |
| } |
| |
| ret = regmap_bulk_write(dev->regmap, 0x800001, coeff_lut[i].val, |
| sizeof(coeff_lut[i].val)); |
| if (ret) |
| goto err; |
| } |
| |
| /* IF frequency control */ |
| if (c->bandwidth_hz != dev->bandwidth_hz) { |
| for (i = 0; i < ARRAY_SIZE(clock_adc_lut); i++) { |
| if (clock_adc_lut[i].clock == dev->cfg.clock) |
| break; |
| } |
| if (i == ARRAY_SIZE(clock_adc_lut)) { |
| dev_err(&client->dev, |
| "Couldn't find ADC clock for clock %u\n", |
| dev->cfg.clock); |
| ret = -EINVAL; |
| goto err; |
| } |
| adc_freq = clock_adc_lut[i].adc; |
| |
| if (dev->cfg.adc_multiplier == AF9033_ADC_MULTIPLIER_2X) |
| adc_freq = 2 * adc_freq; |
| |
| /* Get used IF frequency */ |
| if (fe->ops.tuner_ops.get_if_frequency) |
| fe->ops.tuner_ops.get_if_frequency(fe, &if_frequency); |
| else |
| if_frequency = 0; |
| |
| utmp = DIV_ROUND_CLOSEST_ULL((u64)if_frequency * 0x800000, |
| adc_freq); |
| |
| if (!dev->cfg.spec_inv && if_frequency) |
| utmp = 0x800000 - utmp; |
| |
| buf[0] = (utmp >> 0) & 0xff; |
| buf[1] = (utmp >> 8) & 0xff; |
| buf[2] = (utmp >> 16) & 0xff; |
| ret = regmap_bulk_write(dev->regmap, 0x800029, buf, 3); |
| if (ret) |
| goto err; |
| |
| dev_dbg(&client->dev, "if_frequency_cw=%06x\n", utmp); |
| |
| dev->bandwidth_hz = c->bandwidth_hz; |
| } |
| |
| ret = regmap_update_bits(dev->regmap, 0x80f904, 0x03, |
| bandwidth_reg_val); |
| if (ret) |
| goto err; |
| ret = regmap_write(dev->regmap, 0x800040, 0x00); |
| if (ret) |
| goto err; |
| ret = regmap_write(dev->regmap, 0x800047, 0x00); |
| if (ret) |
| goto err; |
| ret = regmap_update_bits(dev->regmap, 0x80f999, 0x01, 0x00); |
| if (ret) |
| goto err; |
| |
| if (c->frequency <= 230000000) |
| tmp = 0x00; /* VHF */ |
| else |
| tmp = 0x01; /* UHF */ |
| |
| ret = regmap_write(dev->regmap, 0x80004b, tmp); |
| if (ret) |
| goto err; |
| /* Reset FSM */ |
| ret = regmap_write(dev->regmap, 0x800000, 0x00); |
| if (ret) |
| goto err; |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_get_frontend(struct dvb_frontend *fe, |
| struct dtv_frontend_properties *c) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| int ret; |
| u8 buf[8]; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| /* Read all needed TPS registers */ |
| ret = regmap_bulk_read(dev->regmap, 0x80f900, buf, 8); |
| if (ret) |
| goto err; |
| |
| switch ((buf[0] >> 0) & 3) { |
| case 0: |
| c->transmission_mode = TRANSMISSION_MODE_2K; |
| break; |
| case 1: |
| c->transmission_mode = TRANSMISSION_MODE_8K; |
| break; |
| } |
| |
| switch ((buf[1] >> 0) & 3) { |
| case 0: |
| c->guard_interval = GUARD_INTERVAL_1_32; |
| break; |
| case 1: |
| c->guard_interval = GUARD_INTERVAL_1_16; |
| break; |
| case 2: |
| c->guard_interval = GUARD_INTERVAL_1_8; |
| break; |
| case 3: |
| c->guard_interval = GUARD_INTERVAL_1_4; |
| break; |
| } |
| |
| switch ((buf[2] >> 0) & 7) { |
| case 0: |
| c->hierarchy = HIERARCHY_NONE; |
| break; |
| case 1: |
| c->hierarchy = HIERARCHY_1; |
| break; |
| case 2: |
| c->hierarchy = HIERARCHY_2; |
| break; |
| case 3: |
| c->hierarchy = HIERARCHY_4; |
| break; |
| } |
| |
| switch ((buf[3] >> 0) & 3) { |
| case 0: |
| c->modulation = QPSK; |
| break; |
| case 1: |
| c->modulation = QAM_16; |
| break; |
| case 2: |
| c->modulation = QAM_64; |
| break; |
| } |
| |
| switch ((buf[4] >> 0) & 3) { |
| case 0: |
| c->bandwidth_hz = 6000000; |
| break; |
| case 1: |
| c->bandwidth_hz = 7000000; |
| break; |
| case 2: |
| c->bandwidth_hz = 8000000; |
| break; |
| } |
| |
| switch ((buf[6] >> 0) & 7) { |
| case 0: |
| c->code_rate_HP = FEC_1_2; |
| break; |
| case 1: |
| c->code_rate_HP = FEC_2_3; |
| break; |
| case 2: |
| c->code_rate_HP = FEC_3_4; |
| break; |
| case 3: |
| c->code_rate_HP = FEC_5_6; |
| break; |
| case 4: |
| c->code_rate_HP = FEC_7_8; |
| break; |
| case 5: |
| c->code_rate_HP = FEC_NONE; |
| break; |
| } |
| |
| switch ((buf[7] >> 0) & 7) { |
| case 0: |
| c->code_rate_LP = FEC_1_2; |
| break; |
| case 1: |
| c->code_rate_LP = FEC_2_3; |
| break; |
| case 2: |
| c->code_rate_LP = FEC_3_4; |
| break; |
| case 3: |
| c->code_rate_LP = FEC_5_6; |
| break; |
| case 4: |
| c->code_rate_LP = FEC_7_8; |
| break; |
| case 5: |
| c->code_rate_LP = FEC_NONE; |
| break; |
| } |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_read_status(struct dvb_frontend *fe, enum fe_status *status) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| int ret, tmp = 0; |
| u8 buf[7]; |
| unsigned int utmp, utmp1; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| *status = 0; |
| |
| /* Radio channel status: 0=no result, 1=has signal, 2=no signal */ |
| ret = regmap_read(dev->regmap, 0x800047, &utmp); |
| if (ret) |
| goto err; |
| |
| /* Has signal */ |
| if (utmp == 0x01) |
| *status |= FE_HAS_SIGNAL; |
| |
| if (utmp != 0x02) { |
| /* TPS lock */ |
| ret = regmap_read(dev->regmap, 0x80f5a9, &utmp); |
| if (ret) |
| goto err; |
| |
| if ((utmp >> 0) & 0x01) |
| *status |= FE_HAS_SIGNAL | FE_HAS_CARRIER | |
| FE_HAS_VITERBI; |
| |
| /* Full lock */ |
| ret = regmap_read(dev->regmap, 0x80f999, &utmp); |
| if (ret) |
| goto err; |
| |
| if ((utmp >> 0) & 0x01) |
| *status |= FE_HAS_SIGNAL | FE_HAS_CARRIER | |
| FE_HAS_VITERBI | FE_HAS_SYNC | |
| FE_HAS_LOCK; |
| } |
| |
| dev->fe_status = *status; |
| |
| /* Signal strength */ |
| if (dev->fe_status & FE_HAS_SIGNAL) { |
| if (dev->is_af9035) { |
| ret = regmap_read(dev->regmap, 0x80004a, &utmp); |
| if (ret) |
| goto err; |
| tmp = -utmp * 1000; |
| } else { |
| ret = regmap_read(dev->regmap, 0x8000f7, &utmp); |
| if (ret) |
| goto err; |
| tmp = (utmp - 100) * 1000; |
| } |
| |
| c->strength.len = 1; |
| c->strength.stat[0].scale = FE_SCALE_DECIBEL; |
| c->strength.stat[0].svalue = tmp; |
| } else { |
| c->strength.len = 1; |
| c->strength.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| } |
| |
| /* CNR */ |
| if (dev->fe_status & FE_HAS_VITERBI) { |
| /* Read raw SNR value */ |
| ret = regmap_bulk_read(dev->regmap, 0x80002c, buf, 3); |
| if (ret) |
| goto err; |
| |
| utmp1 = buf[2] << 16 | buf[1] << 8 | buf[0] << 0; |
| |
| /* Read superframe number */ |
| ret = regmap_read(dev->regmap, 0x80f78b, &utmp); |
| if (ret) |
| goto err; |
| |
| if (utmp) |
| utmp1 /= utmp; |
| |
| /* Read current transmission mode */ |
| ret = regmap_read(dev->regmap, 0x80f900, &utmp); |
| if (ret) |
| goto err; |
| |
| switch ((utmp >> 0) & 3) { |
| case 0: |
| /* 2k */ |
| utmp1 *= 4; |
| break; |
| case 1: |
| /* 8k */ |
| utmp1 *= 1; |
| break; |
| case 2: |
| /* 4k */ |
| utmp1 *= 2; |
| break; |
| default: |
| utmp1 *= 0; |
| break; |
| } |
| |
| /* Read current modulation */ |
| ret = regmap_read(dev->regmap, 0x80f903, &utmp); |
| if (ret) |
| goto err; |
| |
| switch ((utmp >> 0) & 3) { |
| case 0: |
| /* |
| * QPSK |
| * CNR[dB] 13 * -log10((1690000 - value) / value) + 2.6 |
| * value [653799, 1689999], 2.6 / 13 = 3355443 |
| */ |
| utmp1 = clamp(utmp1, 653799U, 1689999U); |
| utmp1 = ((u64)(intlog10(utmp1) |
| - intlog10(1690000 - utmp1) |
| + 3355443) * 13 * 1000) >> 24; |
| break; |
| case 1: |
| /* |
| * QAM-16 |
| * CNR[dB] 6 * log10((value - 370000) / (828000 - value)) + 15.7 |
| * value [371105, 827999], 15.7 / 6 = 43900382 |
| */ |
| utmp1 = clamp(utmp1, 371105U, 827999U); |
| utmp1 = ((u64)(intlog10(utmp1 - 370000) |
| - intlog10(828000 - utmp1) |
| + 43900382) * 6 * 1000) >> 24; |
| break; |
| case 2: |
| /* |
| * QAM-64 |
| * CNR[dB] 8 * log10((value - 193000) / (425000 - value)) + 23.8 |
| * value [193246, 424999], 23.8 / 8 = 49912218 |
| */ |
| utmp1 = clamp(utmp1, 193246U, 424999U); |
| utmp1 = ((u64)(intlog10(utmp1 - 193000) |
| - intlog10(425000 - utmp1) |
| + 49912218) * 8 * 1000) >> 24; |
| break; |
| default: |
| utmp1 = 0; |
| break; |
| } |
| |
| dev_dbg(&client->dev, "cnr=%u\n", utmp1); |
| |
| c->cnr.stat[0].scale = FE_SCALE_DECIBEL; |
| c->cnr.stat[0].svalue = utmp1; |
| } else { |
| c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| } |
| |
| /* UCB/PER/BER */ |
| if (dev->fe_status & FE_HAS_LOCK) { |
| /* Outer FEC, 204 byte packets */ |
| u16 abort_packet_count, rsd_packet_count; |
| /* Inner FEC, bits */ |
| u32 rsd_bit_err_count; |
| |
| /* |
| * Packet count used for measurement is 10000 |
| * (rsd_packet_count). Maybe it should be increased? |
| */ |
| |
| ret = regmap_bulk_read(dev->regmap, 0x800032, buf, 7); |
| if (ret) |
| goto err; |
| |
| abort_packet_count = (buf[1] << 8) | (buf[0] << 0); |
| rsd_bit_err_count = (buf[4] << 16) | (buf[3] << 8) | buf[2]; |
| rsd_packet_count = (buf[6] << 8) | (buf[5] << 0); |
| |
| dev->error_block_count += abort_packet_count; |
| dev->total_block_count += rsd_packet_count; |
| dev->post_bit_error += rsd_bit_err_count; |
| dev->post_bit_count += rsd_packet_count * 204 * 8; |
| |
| c->block_count.len = 1; |
| c->block_count.stat[0].scale = FE_SCALE_COUNTER; |
| c->block_count.stat[0].uvalue = dev->total_block_count; |
| |
| c->block_error.len = 1; |
| c->block_error.stat[0].scale = FE_SCALE_COUNTER; |
| c->block_error.stat[0].uvalue = dev->error_block_count; |
| |
| c->post_bit_count.len = 1; |
| c->post_bit_count.stat[0].scale = FE_SCALE_COUNTER; |
| c->post_bit_count.stat[0].uvalue = dev->post_bit_count; |
| |
| c->post_bit_error.len = 1; |
| c->post_bit_error.stat[0].scale = FE_SCALE_COUNTER; |
| c->post_bit_error.stat[0].uvalue = dev->post_bit_error; |
| } |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_read_snr(struct dvb_frontend *fe, u16 *snr) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| struct dtv_frontend_properties *c = &dev->fe.dtv_property_cache; |
| int ret; |
| unsigned int utmp; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| /* Use DVBv5 CNR */ |
| if (c->cnr.stat[0].scale == FE_SCALE_DECIBEL) { |
| /* Return 0.1 dB for AF9030 and 0-0xffff for IT9130. */ |
| if (dev->is_af9035) { |
| /* 1000x => 10x (0.1 dB) */ |
| *snr = div_s64(c->cnr.stat[0].svalue, 100); |
| } else { |
| /* 1000x => 1x (1 dB) */ |
| *snr = div_s64(c->cnr.stat[0].svalue, 1000); |
| |
| /* Read current modulation */ |
| ret = regmap_read(dev->regmap, 0x80f903, &utmp); |
| if (ret) |
| goto err; |
| |
| /* scale value to 0x0000-0xffff */ |
| switch ((utmp >> 0) & 3) { |
| case 0: |
| *snr = *snr * 0xffff / 23; |
| break; |
| case 1: |
| *snr = *snr * 0xffff / 26; |
| break; |
| case 2: |
| *snr = *snr * 0xffff / 32; |
| break; |
| default: |
| ret = -EINVAL; |
| goto err; |
| } |
| } |
| } else { |
| *snr = 0; |
| } |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_read_signal_strength(struct dvb_frontend *fe, u16 *strength) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| struct dtv_frontend_properties *c = &dev->fe.dtv_property_cache; |
| int ret, tmp, power_real; |
| unsigned int utmp; |
| u8 gain_offset, buf[7]; |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| if (dev->is_af9035) { |
| /* Read signal strength of 0-100 scale */ |
| ret = regmap_read(dev->regmap, 0x800048, &utmp); |
| if (ret) |
| goto err; |
| |
| /* Scale value to 0x0000-0xffff */ |
| *strength = utmp * 0xffff / 100; |
| } else { |
| ret = regmap_read(dev->regmap, 0x8000f7, &utmp); |
| if (ret) |
| goto err; |
| |
| ret = regmap_bulk_read(dev->regmap, 0x80f900, buf, 7); |
| if (ret) |
| goto err; |
| |
| if (c->frequency <= 300000000) |
| gain_offset = 7; /* VHF */ |
| else |
| gain_offset = 4; /* UHF */ |
| |
| power_real = (utmp - 100 - gain_offset) - |
| power_reference[((buf[3] >> 0) & 3)][((buf[6] >> 0) & 7)]; |
| |
| if (power_real < -15) |
| tmp = 0; |
| else if ((power_real >= -15) && (power_real < 0)) |
| tmp = (2 * (power_real + 15)) / 3; |
| else if ((power_real >= 0) && (power_real < 20)) |
| tmp = 4 * power_real + 10; |
| else if ((power_real >= 20) && (power_real < 35)) |
| tmp = (2 * (power_real - 20)) / 3 + 90; |
| else |
| tmp = 100; |
| |
| /* Scale value to 0x0000-0xffff */ |
| *strength = tmp * 0xffff / 100; |
| } |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_read_ber(struct dvb_frontend *fe, u32 *ber) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| |
| *ber = (dev->post_bit_error - dev->post_bit_error_prev); |
| dev->post_bit_error_prev = dev->post_bit_error; |
| |
| return 0; |
| } |
| |
| static int af9033_read_ucblocks(struct dvb_frontend *fe, u32 *ucblocks) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| |
| *ucblocks = dev->error_block_count; |
| |
| return 0; |
| } |
| |
| static int af9033_i2c_gate_ctrl(struct dvb_frontend *fe, int enable) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| int ret; |
| |
| dev_dbg(&client->dev, "enable=%d\n", enable); |
| |
| ret = regmap_update_bits(dev->regmap, 0x00fa04, 0x01, enable); |
| if (ret) |
| goto err; |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_pid_filter_ctrl(struct dvb_frontend *fe, int onoff) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| int ret; |
| |
| dev_dbg(&client->dev, "onoff=%d\n", onoff); |
| |
| ret = regmap_update_bits(dev->regmap, 0x80f993, 0x01, onoff); |
| if (ret) |
| goto err; |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static int af9033_pid_filter(struct dvb_frontend *fe, int index, u16 pid, |
| int onoff) |
| { |
| struct af9033_dev *dev = fe->demodulator_priv; |
| struct i2c_client *client = dev->client; |
| int ret; |
| u8 wbuf[2] = {(pid >> 0) & 0xff, (pid >> 8) & 0xff}; |
| |
| dev_dbg(&client->dev, "index=%d pid=%04x onoff=%d\n", |
| index, pid, onoff); |
| |
| if (pid > 0x1fff) |
| return 0; |
| |
| ret = regmap_bulk_write(dev->regmap, 0x80f996, wbuf, 2); |
| if (ret) |
| goto err; |
| ret = regmap_write(dev->regmap, 0x80f994, onoff); |
| if (ret) |
| goto err; |
| ret = regmap_write(dev->regmap, 0x80f995, index); |
| if (ret) |
| goto err; |
| |
| return 0; |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static const struct dvb_frontend_ops af9033_ops = { |
| .delsys = {SYS_DVBT}, |
| .info = { |
| .name = "Afatech AF9033 (DVB-T)", |
| .frequency_min_hz = 174 * MHz, |
| .frequency_max_hz = 862 * MHz, |
| .frequency_stepsize_hz = 250 * kHz, |
| .caps = FE_CAN_FEC_1_2 | |
| FE_CAN_FEC_2_3 | |
| FE_CAN_FEC_3_4 | |
| FE_CAN_FEC_5_6 | |
| FE_CAN_FEC_7_8 | |
| FE_CAN_FEC_AUTO | |
| FE_CAN_QPSK | |
| FE_CAN_QAM_16 | |
| FE_CAN_QAM_64 | |
| FE_CAN_QAM_AUTO | |
| FE_CAN_TRANSMISSION_MODE_AUTO | |
| FE_CAN_GUARD_INTERVAL_AUTO | |
| FE_CAN_HIERARCHY_AUTO | |
| FE_CAN_RECOVER | |
| FE_CAN_MUTE_TS |
| }, |
| |
| .init = af9033_init, |
| .sleep = af9033_sleep, |
| |
| .get_tune_settings = af9033_get_tune_settings, |
| .set_frontend = af9033_set_frontend, |
| .get_frontend = af9033_get_frontend, |
| |
| .read_status = af9033_read_status, |
| .read_snr = af9033_read_snr, |
| .read_signal_strength = af9033_read_signal_strength, |
| .read_ber = af9033_read_ber, |
| .read_ucblocks = af9033_read_ucblocks, |
| |
| .i2c_gate_ctrl = af9033_i2c_gate_ctrl, |
| }; |
| |
| static int af9033_probe(struct i2c_client *client) |
| { |
| struct af9033_config *cfg = client->dev.platform_data; |
| struct af9033_dev *dev; |
| int ret; |
| u8 buf[8]; |
| u32 reg; |
| static const struct regmap_config regmap_config = { |
| .reg_bits = 24, |
| .val_bits = 8, |
| }; |
| |
| /* Allocate memory for the internal state */ |
| dev = kzalloc(sizeof(*dev), GFP_KERNEL); |
| if (!dev) { |
| ret = -ENOMEM; |
| goto err; |
| } |
| |
| /* Setup the state */ |
| dev->client = client; |
| memcpy(&dev->cfg, cfg, sizeof(dev->cfg)); |
| switch (dev->cfg.ts_mode) { |
| case AF9033_TS_MODE_PARALLEL: |
| dev->ts_mode_parallel = true; |
| break; |
| case AF9033_TS_MODE_SERIAL: |
| dev->ts_mode_serial = true; |
| break; |
| case AF9033_TS_MODE_USB: |
| /* USB mode for AF9035 */ |
| default: |
| break; |
| } |
| |
| if (dev->cfg.clock != 12000000) { |
| ret = -ENODEV; |
| dev_err(&client->dev, |
| "Unsupported clock %u Hz. Only 12000000 Hz is supported currently\n", |
| dev->cfg.clock); |
| goto err_kfree; |
| } |
| |
| /* Create regmap */ |
| dev->regmap = regmap_init_i2c(client, ®map_config); |
| if (IS_ERR(dev->regmap)) { |
| ret = PTR_ERR(dev->regmap); |
| goto err_kfree; |
| } |
| |
| /* Firmware version */ |
| switch (dev->cfg.tuner) { |
| case AF9033_TUNER_IT9135_38: |
| case AF9033_TUNER_IT9135_51: |
| case AF9033_TUNER_IT9135_52: |
| case AF9033_TUNER_IT9135_60: |
| case AF9033_TUNER_IT9135_61: |
| case AF9033_TUNER_IT9135_62: |
| dev->is_it9135 = true; |
| reg = 0x004bfc; |
| break; |
| default: |
| dev->is_af9035 = true; |
| reg = 0x0083e9; |
| break; |
| } |
| |
| ret = regmap_bulk_read(dev->regmap, reg, &buf[0], 4); |
| if (ret) |
| goto err_regmap_exit; |
| ret = regmap_bulk_read(dev->regmap, 0x804191, &buf[4], 4); |
| if (ret) |
| goto err_regmap_exit; |
| |
| dev_info(&client->dev, |
| "firmware version: LINK %d.%d.%d.%d - OFDM %d.%d.%d.%d\n", |
| buf[0], buf[1], buf[2], buf[3], |
| buf[4], buf[5], buf[6], buf[7]); |
| |
| /* Sleep as chip seems to be partly active by default */ |
| /* IT9135 did not like to sleep at that early */ |
| if (dev->is_af9035) { |
| ret = regmap_write(dev->regmap, 0x80004c, 0x01); |
| if (ret) |
| goto err_regmap_exit; |
| ret = regmap_write(dev->regmap, 0x800000, 0x00); |
| if (ret) |
| goto err_regmap_exit; |
| } |
| |
| /* Create dvb frontend */ |
| memcpy(&dev->fe.ops, &af9033_ops, sizeof(dev->fe.ops)); |
| dev->fe.demodulator_priv = dev; |
| *cfg->fe = &dev->fe; |
| if (cfg->ops) { |
| cfg->ops->pid_filter = af9033_pid_filter; |
| cfg->ops->pid_filter_ctrl = af9033_pid_filter_ctrl; |
| } |
| cfg->regmap = dev->regmap; |
| i2c_set_clientdata(client, dev); |
| |
| dev_info(&client->dev, "Afatech AF9033 successfully attached\n"); |
| |
| return 0; |
| err_regmap_exit: |
| regmap_exit(dev->regmap); |
| err_kfree: |
| kfree(dev); |
| err: |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static void af9033_remove(struct i2c_client *client) |
| { |
| struct af9033_dev *dev = i2c_get_clientdata(client); |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| regmap_exit(dev->regmap); |
| kfree(dev); |
| } |
| |
| static const struct i2c_device_id af9033_id_table[] = { |
| { "af9033" }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, af9033_id_table); |
| |
| static struct i2c_driver af9033_driver = { |
| .driver = { |
| .name = "af9033", |
| .suppress_bind_attrs = true, |
| }, |
| .probe = af9033_probe, |
| .remove = af9033_remove, |
| .id_table = af9033_id_table, |
| }; |
| |
| module_i2c_driver(af9033_driver); |
| |
| MODULE_AUTHOR("Antti Palosaari <crope@iki.fi>"); |
| MODULE_DESCRIPTION("Afatech AF9033 DVB-T demodulator driver"); |
| MODULE_LICENSE("GPL"); |