| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Rockchip PIPE USB3.0 PCIE SATA Combo Phy driver |
| * |
| * Copyright (C) 2021 Rockchip Electronics Co., Ltd. |
| */ |
| |
| #include <dt-bindings/phy/phy.h> |
| #include <linux/clk.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/of.h> |
| #include <linux/phy/phy.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/reset.h> |
| #include <linux/units.h> |
| |
| #define BIT_WRITEABLE_SHIFT 16 |
| #define REF_CLOCK_24MHz (24 * HZ_PER_MHZ) |
| #define REF_CLOCK_25MHz (25 * HZ_PER_MHZ) |
| #define REF_CLOCK_100MHz (100 * HZ_PER_MHZ) |
| |
| /* COMBO PHY REG */ |
| #define PHYREG6 0x14 |
| #define PHYREG6_PLL_DIV_MASK GENMASK(7, 6) |
| #define PHYREG6_PLL_DIV_SHIFT 6 |
| #define PHYREG6_PLL_DIV_2 1 |
| |
| #define PHYREG7 0x18 |
| #define PHYREG7_TX_RTERM_MASK GENMASK(7, 4) |
| #define PHYREG7_TX_RTERM_SHIFT 4 |
| #define PHYREG7_TX_RTERM_50OHM 8 |
| #define PHYREG7_RX_RTERM_MASK GENMASK(3, 0) |
| #define PHYREG7_RX_RTERM_SHIFT 0 |
| #define PHYREG7_RX_RTERM_44OHM 15 |
| |
| #define PHYREG8 0x1C |
| #define PHYREG8_SSC_EN BIT(4) |
| |
| #define PHYREG11 0x28 |
| #define PHYREG11_SU_TRIM_0_7 0xF0 |
| |
| #define PHYREG12 0x2C |
| #define PHYREG12_PLL_LPF_ADJ_VALUE 4 |
| |
| #define PHYREG13 0x30 |
| #define PHYREG13_RESISTER_MASK GENMASK(5, 4) |
| #define PHYREG13_RESISTER_SHIFT 0x4 |
| #define PHYREG13_RESISTER_HIGH_Z 3 |
| #define PHYREG13_CKRCV_AMP0 BIT(7) |
| |
| #define PHYREG14 0x34 |
| #define PHYREG14_CKRCV_AMP1 BIT(0) |
| |
| #define PHYREG15 0x38 |
| #define PHYREG15_CTLE_EN BIT(0) |
| #define PHYREG15_SSC_CNT_MASK GENMASK(7, 6) |
| #define PHYREG15_SSC_CNT_SHIFT 6 |
| #define PHYREG15_SSC_CNT_VALUE 1 |
| |
| #define PHYREG16 0x3C |
| #define PHYREG16_SSC_CNT_VALUE 0x5f |
| |
| #define PHYREG18 0x44 |
| #define PHYREG18_PLL_LOOP 0x32 |
| |
| #define PHYREG27 0x6C |
| #define PHYREG27_RX_TRIM_RK3588 0x4C |
| |
| #define PHYREG32 0x7C |
| #define PHYREG32_SSC_MASK GENMASK(7, 4) |
| #define PHYREG32_SSC_DIR_SHIFT 4 |
| #define PHYREG32_SSC_UPWARD 0 |
| #define PHYREG32_SSC_DOWNWARD 1 |
| #define PHYREG32_SSC_OFFSET_SHIFT 6 |
| #define PHYREG32_SSC_OFFSET_500PPM 1 |
| |
| #define PHYREG33 0x80 |
| #define PHYREG33_PLL_KVCO_MASK GENMASK(4, 2) |
| #define PHYREG33_PLL_KVCO_SHIFT 2 |
| #define PHYREG33_PLL_KVCO_VALUE 2 |
| |
| struct rockchip_combphy_priv; |
| |
| struct combphy_reg { |
| u16 offset; |
| u16 bitend; |
| u16 bitstart; |
| u16 disable; |
| u16 enable; |
| }; |
| |
| struct rockchip_combphy_grfcfg { |
| struct combphy_reg pcie_mode_set; |
| struct combphy_reg usb_mode_set; |
| struct combphy_reg sgmii_mode_set; |
| struct combphy_reg qsgmii_mode_set; |
| struct combphy_reg pipe_rxterm_set; |
| struct combphy_reg pipe_txelec_set; |
| struct combphy_reg pipe_txcomp_set; |
| struct combphy_reg pipe_clk_25m; |
| struct combphy_reg pipe_clk_100m; |
| struct combphy_reg pipe_phymode_sel; |
| struct combphy_reg pipe_rate_sel; |
| struct combphy_reg pipe_rxterm_sel; |
| struct combphy_reg pipe_txelec_sel; |
| struct combphy_reg pipe_txcomp_sel; |
| struct combphy_reg pipe_clk_ext; |
| struct combphy_reg pipe_sel_usb; |
| struct combphy_reg pipe_sel_qsgmii; |
| struct combphy_reg pipe_phy_status; |
| struct combphy_reg con0_for_pcie; |
| struct combphy_reg con1_for_pcie; |
| struct combphy_reg con2_for_pcie; |
| struct combphy_reg con3_for_pcie; |
| struct combphy_reg con0_for_sata; |
| struct combphy_reg con1_for_sata; |
| struct combphy_reg con2_for_sata; |
| struct combphy_reg con3_for_sata; |
| struct combphy_reg pipe_con0_for_sata; |
| struct combphy_reg pipe_con1_for_sata; |
| struct combphy_reg pipe_xpcs_phy_ready; |
| struct combphy_reg pipe_pcie1l0_sel; |
| struct combphy_reg pipe_pcie1l1_sel; |
| }; |
| |
| struct rockchip_combphy_cfg { |
| unsigned int num_phys; |
| unsigned int phy_ids[3]; |
| const struct rockchip_combphy_grfcfg *grfcfg; |
| int (*combphy_cfg)(struct rockchip_combphy_priv *priv); |
| }; |
| |
| struct rockchip_combphy_priv { |
| u8 type; |
| int id; |
| void __iomem *mmio; |
| int num_clks; |
| struct clk_bulk_data *clks; |
| struct device *dev; |
| struct regmap *pipe_grf; |
| struct regmap *phy_grf; |
| struct phy *phy; |
| struct reset_control *phy_rst; |
| const struct rockchip_combphy_cfg *cfg; |
| bool enable_ssc; |
| bool ext_refclk; |
| struct clk *refclk; |
| }; |
| |
| static void rockchip_combphy_updatel(struct rockchip_combphy_priv *priv, |
| int mask, int val, int reg) |
| { |
| unsigned int temp; |
| |
| temp = readl(priv->mmio + reg); |
| temp = (temp & ~(mask)) | val; |
| writel(temp, priv->mmio + reg); |
| } |
| |
| static int rockchip_combphy_param_write(struct regmap *base, |
| const struct combphy_reg *reg, bool en) |
| { |
| u32 val, mask, tmp; |
| |
| tmp = en ? reg->enable : reg->disable; |
| mask = GENMASK(reg->bitend, reg->bitstart); |
| val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT); |
| |
| return regmap_write(base, reg->offset, val); |
| } |
| |
| static u32 rockchip_combphy_is_ready(struct rockchip_combphy_priv *priv) |
| { |
| const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg; |
| u32 mask, val; |
| |
| mask = GENMASK(cfg->pipe_phy_status.bitend, |
| cfg->pipe_phy_status.bitstart); |
| |
| regmap_read(priv->phy_grf, cfg->pipe_phy_status.offset, &val); |
| val = (val & mask) >> cfg->pipe_phy_status.bitstart; |
| |
| return val; |
| } |
| |
| static int rockchip_combphy_init(struct phy *phy) |
| { |
| struct rockchip_combphy_priv *priv = phy_get_drvdata(phy); |
| const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg; |
| u32 val; |
| int ret; |
| |
| ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks); |
| if (ret) { |
| dev_err(priv->dev, "failed to enable clks\n"); |
| return ret; |
| } |
| |
| switch (priv->type) { |
| case PHY_TYPE_PCIE: |
| case PHY_TYPE_USB3: |
| case PHY_TYPE_SATA: |
| case PHY_TYPE_SGMII: |
| case PHY_TYPE_QSGMII: |
| if (priv->cfg->combphy_cfg) |
| ret = priv->cfg->combphy_cfg(priv); |
| break; |
| default: |
| dev_err(priv->dev, "incompatible PHY type\n"); |
| ret = -EINVAL; |
| break; |
| } |
| |
| if (ret) { |
| dev_err(priv->dev, "failed to init phy for phy type %x\n", priv->type); |
| goto err_clk; |
| } |
| |
| ret = reset_control_deassert(priv->phy_rst); |
| if (ret) |
| goto err_clk; |
| |
| if (priv->type == PHY_TYPE_USB3) { |
| ret = readx_poll_timeout_atomic(rockchip_combphy_is_ready, |
| priv, val, |
| val == cfg->pipe_phy_status.enable, |
| 10, 1000); |
| if (ret) |
| dev_warn(priv->dev, "wait phy status ready timeout\n"); |
| } |
| |
| return 0; |
| |
| err_clk: |
| clk_bulk_disable_unprepare(priv->num_clks, priv->clks); |
| |
| return ret; |
| } |
| |
| static int rockchip_combphy_exit(struct phy *phy) |
| { |
| struct rockchip_combphy_priv *priv = phy_get_drvdata(phy); |
| |
| clk_bulk_disable_unprepare(priv->num_clks, priv->clks); |
| reset_control_assert(priv->phy_rst); |
| |
| return 0; |
| } |
| |
| static const struct phy_ops rockchip_combphy_ops = { |
| .init = rockchip_combphy_init, |
| .exit = rockchip_combphy_exit, |
| .owner = THIS_MODULE, |
| }; |
| |
| static struct phy *rockchip_combphy_xlate(struct device *dev, const struct of_phandle_args *args) |
| { |
| struct rockchip_combphy_priv *priv = dev_get_drvdata(dev); |
| |
| if (args->args_count != 1) { |
| dev_err(dev, "invalid number of arguments\n"); |
| return ERR_PTR(-EINVAL); |
| } |
| |
| if (priv->type != PHY_NONE && priv->type != args->args[0]) |
| dev_warn(dev, "phy type select %d overwriting type %d\n", |
| args->args[0], priv->type); |
| |
| priv->type = args->args[0]; |
| |
| return priv->phy; |
| } |
| |
| static int rockchip_combphy_parse_dt(struct device *dev, struct rockchip_combphy_priv *priv) |
| { |
| int i; |
| |
| priv->num_clks = devm_clk_bulk_get_all(dev, &priv->clks); |
| if (priv->num_clks < 1) |
| return -EINVAL; |
| |
| priv->refclk = NULL; |
| for (i = 0; i < priv->num_clks; i++) { |
| if (!strncmp(priv->clks[i].id, "ref", 3)) { |
| priv->refclk = priv->clks[i].clk; |
| break; |
| } |
| } |
| |
| if (!priv->refclk) { |
| dev_err(dev, "no refclk found\n"); |
| return -EINVAL; |
| } |
| |
| priv->pipe_grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,pipe-grf"); |
| if (IS_ERR(priv->pipe_grf)) { |
| dev_err(dev, "failed to find peri_ctrl pipe-grf regmap\n"); |
| return PTR_ERR(priv->pipe_grf); |
| } |
| |
| priv->phy_grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,pipe-phy-grf"); |
| if (IS_ERR(priv->phy_grf)) { |
| dev_err(dev, "failed to find peri_ctrl pipe-phy-grf regmap\n"); |
| return PTR_ERR(priv->phy_grf); |
| } |
| |
| priv->enable_ssc = device_property_present(dev, "rockchip,enable-ssc"); |
| |
| priv->ext_refclk = device_property_present(dev, "rockchip,ext-refclk"); |
| |
| priv->phy_rst = devm_reset_control_array_get_exclusive(dev); |
| if (IS_ERR(priv->phy_rst)) |
| return dev_err_probe(dev, PTR_ERR(priv->phy_rst), "failed to get phy reset\n"); |
| |
| return 0; |
| } |
| |
| static int rockchip_combphy_probe(struct platform_device *pdev) |
| { |
| struct phy_provider *phy_provider; |
| struct device *dev = &pdev->dev; |
| struct rockchip_combphy_priv *priv; |
| const struct rockchip_combphy_cfg *phy_cfg; |
| struct resource *res; |
| int ret, id; |
| |
| phy_cfg = of_device_get_match_data(dev); |
| if (!phy_cfg) { |
| dev_err(dev, "no OF match data provided\n"); |
| return -EINVAL; |
| } |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res); |
| if (IS_ERR(priv->mmio)) { |
| ret = PTR_ERR(priv->mmio); |
| return ret; |
| } |
| |
| /* find the phy-id from the io address */ |
| priv->id = -ENODEV; |
| for (id = 0; id < phy_cfg->num_phys; id++) { |
| if (res->start == phy_cfg->phy_ids[id]) { |
| priv->id = id; |
| break; |
| } |
| } |
| |
| priv->dev = dev; |
| priv->type = PHY_NONE; |
| priv->cfg = phy_cfg; |
| |
| ret = rockchip_combphy_parse_dt(dev, priv); |
| if (ret) |
| return ret; |
| |
| ret = reset_control_assert(priv->phy_rst); |
| if (ret) { |
| dev_err(dev, "failed to reset phy\n"); |
| return ret; |
| } |
| |
| priv->phy = devm_phy_create(dev, NULL, &rockchip_combphy_ops); |
| if (IS_ERR(priv->phy)) { |
| dev_err(dev, "failed to create combphy\n"); |
| return PTR_ERR(priv->phy); |
| } |
| |
| dev_set_drvdata(dev, priv); |
| phy_set_drvdata(priv->phy, priv); |
| |
| phy_provider = devm_of_phy_provider_register(dev, rockchip_combphy_xlate); |
| |
| return PTR_ERR_OR_ZERO(phy_provider); |
| } |
| |
| static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv) |
| { |
| const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg; |
| unsigned long rate; |
| u32 val; |
| |
| switch (priv->type) { |
| case PHY_TYPE_PCIE: |
| /* Set SSC downward spread spectrum. */ |
| rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, |
| PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT, |
| PHYREG32); |
| |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true); |
| break; |
| |
| case PHY_TYPE_USB3: |
| /* Set SSC downward spread spectrum. */ |
| rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, |
| PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT, |
| PHYREG32); |
| |
| /* Enable adaptive CTLE for USB3.0 Rx. */ |
| val = readl(priv->mmio + PHYREG15); |
| val |= PHYREG15_CTLE_EN; |
| writel(val, priv->mmio + PHYREG15); |
| |
| /* Set PLL KVCO fine tuning signals. */ |
| rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, |
| PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT, |
| PHYREG33); |
| |
| /* Enable controlling random jitter. */ |
| writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12); |
| |
| /* Set PLL input clock divider 1/2. */ |
| rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, |
| PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT, |
| PHYREG6); |
| |
| writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18); |
| writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11); |
| |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_usb, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true); |
| break; |
| |
| case PHY_TYPE_SATA: |
| /* Enable adaptive CTLE for SATA Rx. */ |
| val = readl(priv->mmio + PHYREG15); |
| val |= PHYREG15_CTLE_EN; |
| writel(val, priv->mmio + PHYREG15); |
| /* |
| * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA. |
| * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm) |
| */ |
| val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT; |
| val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT; |
| writel(val, priv->mmio + PHYREG7); |
| |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true); |
| rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true); |
| break; |
| |
| case PHY_TYPE_SGMII: |
| rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->sgmii_mode_set, true); |
| break; |
| |
| case PHY_TYPE_QSGMII: |
| rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_rate_sel, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->qsgmii_mode_set, true); |
| break; |
| |
| default: |
| dev_err(priv->dev, "incompatible PHY type\n"); |
| return -EINVAL; |
| } |
| |
| rate = clk_get_rate(priv->refclk); |
| |
| switch (rate) { |
| case REF_CLOCK_24MHz: |
| if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) { |
| /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */ |
| val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT; |
| rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK, |
| val, PHYREG15); |
| |
| writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16); |
| } |
| break; |
| |
| case REF_CLOCK_25MHz: |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true); |
| break; |
| |
| case REF_CLOCK_100MHz: |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true); |
| if (priv->type == PHY_TYPE_PCIE) { |
| /* PLL KVCO fine tuning. */ |
| val = PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT; |
| rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, |
| val, PHYREG33); |
| |
| /* Enable controlling random jitter. */ |
| writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12); |
| |
| val = PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT; |
| rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, |
| val, PHYREG6); |
| |
| writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18); |
| writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11); |
| } else if (priv->type == PHY_TYPE_SATA) { |
| /* downward spread spectrum +500ppm */ |
| val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT; |
| val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT; |
| rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32); |
| } |
| break; |
| |
| default: |
| dev_err(priv->dev, "unsupported rate: %lu\n", rate); |
| return -EINVAL; |
| } |
| |
| if (priv->ext_refclk) { |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true); |
| if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) { |
| val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT; |
| val |= PHYREG13_CKRCV_AMP0; |
| rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13); |
| |
| val = readl(priv->mmio + PHYREG14); |
| val |= PHYREG14_CKRCV_AMP1; |
| writel(val, priv->mmio + PHYREG14); |
| } |
| } |
| |
| if (priv->enable_ssc) { |
| val = readl(priv->mmio + PHYREG8); |
| val |= PHYREG8_SSC_EN; |
| writel(val, priv->mmio + PHYREG8); |
| } |
| |
| return 0; |
| } |
| |
| static const struct rockchip_combphy_grfcfg rk3568_combphy_grfcfgs = { |
| /* pipe-phy-grf */ |
| .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 }, |
| .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 }, |
| .sgmii_mode_set = { 0x0000, 5, 0, 0x00, 0x01 }, |
| .qsgmii_mode_set = { 0x0000, 5, 0, 0x00, 0x21 }, |
| .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 }, |
| .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 }, |
| .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 }, |
| .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 }, |
| .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 }, |
| .pipe_phymode_sel = { 0x0008, 1, 1, 0x00, 0x01 }, |
| .pipe_rate_sel = { 0x0008, 2, 2, 0x00, 0x01 }, |
| .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 }, |
| .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 }, |
| .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 }, |
| .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 }, |
| .pipe_sel_usb = { 0x000c, 14, 13, 0x00, 0x01 }, |
| .pipe_sel_qsgmii = { 0x000c, 15, 13, 0x00, 0x07 }, |
| .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 }, |
| .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 }, |
| .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 }, |
| .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 }, |
| .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 }, |
| .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0119 }, |
| .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0040 }, |
| .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c3 }, |
| .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x4407 }, |
| /* pipe-grf */ |
| .pipe_con0_for_sata = { 0x0000, 15, 0, 0x00, 0x2220 }, |
| .pipe_xpcs_phy_ready = { 0x0040, 2, 2, 0x00, 0x01 }, |
| }; |
| |
| static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = { |
| .num_phys = 3, |
| .phy_ids = { |
| 0xfe820000, |
| 0xfe830000, |
| 0xfe840000, |
| }, |
| .grfcfg = &rk3568_combphy_grfcfgs, |
| .combphy_cfg = rk3568_combphy_cfg, |
| }; |
| |
| static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv) |
| { |
| const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg; |
| unsigned long rate; |
| u32 val; |
| |
| switch (priv->type) { |
| case PHY_TYPE_PCIE: |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true); |
| switch (priv->id) { |
| case 1: |
| rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_pcie1l0_sel, true); |
| break; |
| case 2: |
| rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_pcie1l1_sel, true); |
| break; |
| } |
| break; |
| case PHY_TYPE_USB3: |
| /* Set SSC downward spread spectrum */ |
| rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, |
| PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT, |
| PHYREG32); |
| |
| /* Enable adaptive CTLE for USB3.0 Rx. */ |
| val = readl(priv->mmio + PHYREG15); |
| val |= PHYREG15_CTLE_EN; |
| writel(val, priv->mmio + PHYREG15); |
| |
| /* Set PLL KVCO fine tuning signals. */ |
| rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, |
| PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT, |
| PHYREG33); |
| |
| /* Enable controlling random jitter. */ |
| writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12); |
| |
| /* Set PLL input clock divider 1/2. */ |
| rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, |
| PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT, |
| PHYREG6); |
| |
| writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18); |
| writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11); |
| |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true); |
| break; |
| case PHY_TYPE_SATA: |
| /* Enable adaptive CTLE for SATA Rx. */ |
| val = readl(priv->mmio + PHYREG15); |
| val |= PHYREG15_CTLE_EN; |
| writel(val, priv->mmio + PHYREG15); |
| /* |
| * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA. |
| * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm) |
| */ |
| val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT; |
| val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT; |
| writel(val, priv->mmio + PHYREG7); |
| |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true); |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true); |
| rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true); |
| rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con1_for_sata, true); |
| break; |
| case PHY_TYPE_SGMII: |
| case PHY_TYPE_QSGMII: |
| default: |
| dev_err(priv->dev, "incompatible PHY type\n"); |
| return -EINVAL; |
| } |
| |
| rate = clk_get_rate(priv->refclk); |
| |
| switch (rate) { |
| case REF_CLOCK_24MHz: |
| if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) { |
| /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */ |
| val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT; |
| rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK, |
| val, PHYREG15); |
| |
| writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16); |
| } |
| break; |
| |
| case REF_CLOCK_25MHz: |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true); |
| break; |
| case REF_CLOCK_100MHz: |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true); |
| if (priv->type == PHY_TYPE_PCIE) { |
| /* PLL KVCO fine tuning. */ |
| val = 4 << PHYREG33_PLL_KVCO_SHIFT; |
| rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, |
| val, PHYREG33); |
| |
| /* Enable controlling random jitter. */ |
| writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12); |
| |
| /* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */ |
| writel(PHYREG27_RX_TRIM_RK3588, priv->mmio + PHYREG27); |
| |
| /* Set up su_trim: */ |
| writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11); |
| } else if (priv->type == PHY_TYPE_SATA) { |
| /* downward spread spectrum +500ppm */ |
| val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT; |
| val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT; |
| rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32); |
| } |
| break; |
| default: |
| dev_err(priv->dev, "Unsupported rate: %lu\n", rate); |
| return -EINVAL; |
| } |
| |
| if (priv->ext_refclk) { |
| rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true); |
| if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) { |
| val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT; |
| val |= PHYREG13_CKRCV_AMP0; |
| rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13); |
| |
| val = readl(priv->mmio + PHYREG14); |
| val |= PHYREG14_CKRCV_AMP1; |
| writel(val, priv->mmio + PHYREG14); |
| } |
| } |
| |
| if (priv->enable_ssc) { |
| val = readl(priv->mmio + PHYREG8); |
| val |= PHYREG8_SSC_EN; |
| writel(val, priv->mmio + PHYREG8); |
| } |
| |
| return 0; |
| } |
| |
| static const struct rockchip_combphy_grfcfg rk3588_combphy_grfcfgs = { |
| /* pipe-phy-grf */ |
| .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 }, |
| .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 }, |
| .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 }, |
| .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 }, |
| .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 }, |
| .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 }, |
| .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 }, |
| .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 }, |
| .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 }, |
| .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 }, |
| .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 }, |
| .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 }, |
| .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 }, |
| .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 }, |
| .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 }, |
| .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 }, |
| .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0129 }, |
| .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0000 }, |
| .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c1 }, |
| .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x0407 }, |
| /* pipe-grf */ |
| .pipe_con0_for_sata = { 0x0000, 11, 5, 0x00, 0x22 }, |
| .pipe_con1_for_sata = { 0x0000, 2, 0, 0x00, 0x2 }, |
| .pipe_pcie1l0_sel = { 0x0100, 0, 0, 0x01, 0x0 }, |
| .pipe_pcie1l1_sel = { 0x0100, 1, 1, 0x01, 0x0 }, |
| }; |
| |
| static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = { |
| .num_phys = 3, |
| .phy_ids = { |
| 0xfee00000, |
| 0xfee10000, |
| 0xfee20000, |
| }, |
| .grfcfg = &rk3588_combphy_grfcfgs, |
| .combphy_cfg = rk3588_combphy_cfg, |
| }; |
| |
| static const struct of_device_id rockchip_combphy_of_match[] = { |
| { |
| .compatible = "rockchip,rk3568-naneng-combphy", |
| .data = &rk3568_combphy_cfgs, |
| }, |
| { |
| .compatible = "rockchip,rk3588-naneng-combphy", |
| .data = &rk3588_combphy_cfgs, |
| }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, rockchip_combphy_of_match); |
| |
| static struct platform_driver rockchip_combphy_driver = { |
| .probe = rockchip_combphy_probe, |
| .driver = { |
| .name = "rockchip-naneng-combphy", |
| .of_match_table = rockchip_combphy_of_match, |
| }, |
| }; |
| module_platform_driver(rockchip_combphy_driver); |
| |
| MODULE_DESCRIPTION("Rockchip NANENG COMBPHY driver"); |
| MODULE_LICENSE("GPL v2"); |