diff --git a/Documentation/arm/00-INDEX b/Documentation/arm/00-INDEX
index 91c24a1..36420e1 100644
--- a/Documentation/arm/00-INDEX
+++ b/Documentation/arm/00-INDEX
@@ -4,8 +4,6 @@
 	- requirements for booting
 Interrupts
 	- ARM Interrupt subsystem documentation
-IXP2000
-	- Release Notes for Linux on Intel's IXP2000 Network Processor
 msm
 	- MSM specific documentation
 Netwinder
diff --git a/Documentation/arm/IXP2000 b/Documentation/arm/IXP2000
deleted file mode 100644
index 68d21d9..0000000
--- a/Documentation/arm/IXP2000
+++ /dev/null
@@ -1,69 +0,0 @@
-
--------------------------------------------------------------------------
-Release Notes for Linux on Intel's IXP2000 Network Processor
-
-Maintained by Deepak Saxena <dsaxena@plexity.net>
--------------------------------------------------------------------------
-
-1. Overview
-
-Intel's IXP2000 family of NPUs (IXP2400, IXP2800, IXP2850) is designed
-for high-performance network applications such high-availability
-telecom systems. In addition to an XScale core, it contains up to 8
-"MicroEngines" that run special code, several high-end networking 
-interfaces (UTOPIA, SPI, etc), a PCI host bridge, one serial port,
-flash interface, and some other odds and ends. For more information, see:
-
-http://developer.intel.com
-
-2. Linux Support
-
-Linux currently supports the following features on the IXP2000 NPUs:
-
-- On-chip serial
-- PCI
-- Flash (MTD/JFFS2)
-- I2C through GPIO
-- Timers (watchdog, OS)
-
-That is about all we can support under Linux ATM b/c the core networking
-components of the chip are accessed via Intel's closed source SDK. 
-Please contact Intel directly on issues with using those. There is
-also a mailing list run by some folks at Princeton University that might
-be of help:  https://lists.cs.princeton.edu/mailman/listinfo/ixp2xxx
-
-WHATEVER YOU DO, DO NOT POST EMAIL TO THE LINUX-ARM OR LINUX-ARM-KERNEL
-MAILING LISTS REGARDING THE INTEL SDK.
-
-3. Supported Platforms
-
-- Intel IXDP2400 Reference Platform
-- Intel IXDP2800 Reference Platform
-- Intel IXDP2401 Reference Platform
-- Intel IXDP2801 Reference Platform
-- RadiSys ENP-2611
-
-4. Usage Notes
-
-- The IXP2000 platforms usually have rather complex PCI bus topologies
-  with large memory space requirements. In addition, b/c of the way the
-  Intel SDK is designed, devices are enumerated in a very specific
-  way. B/c of this this, we use "pci=firmware" option in the kernel
-  command line so that we do not re-enumerate the bus.
-
-- IXDP2x01 systems have variable clock tick rates that we cannot determine 
-  via HW registers. The "ixdp2x01_clk=XXX" cmd line options allow you
-  to pass the clock rate to the board port.
-
-5. Thanks
-
-The IXP2000 work has been funded by Intel Corp. and MontaVista Software, Inc.
-
-The following people have contributed patches/comments/etc:
-
-Naeem F. Afzal
-Lennert Buytenhek
-Jeffrey Daly
-
--------------------------------------------------------------------------
-Last Update: 8/09/2004
diff --git a/MAINTAINERS b/MAINTAINERS
index 1a2f8f5..069ec40 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -640,13 +640,6 @@
 F:	drivers/amba/
 F:	include/linux/amba/bus.h
 
-ARM/ADI ROADRUNNER MACHINE SUPPORT
-M:	Lennert Buytenhek <kernel@wantstofly.org>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-F:	arch/arm/mach-ixp23xx/
-F:	arch/arm/mach-ixp23xx/include/mach/
-
 ARM/ADS SPHERE MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -859,21 +852,11 @@
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
-ARM/INTEL IXP2000 ARM ARCHITECTURE
-M:	Lennert Buytenhek <kernel@wantstofly.org>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-
 ARM/INTEL IXDP2850 MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
-ARM/INTEL IXP23XX ARM ARCHITECTURE
-M:	Lennert Buytenhek <kernel@wantstofly.org>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-
 ARM/INTEL IXP4XX ARM ARCHITECTURE
 M:	Imre Kaloz <kaloz@openwrt.org>
 M:	Krzysztof Halasa <khc@pm.waw.pl>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index cf006d4..a231594 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -340,8 +340,8 @@
 	select IRQ_DOMAIN
 	select NEED_MACH_IO_H if PCCARD
 	help
-	  This enables support for systems based on the Atmel AT91RM9200,
-	  AT91SAM9 processors.
+	  This enables support for systems based on Atmel
+	  AT91RM9200 and AT91SAM9* processors.
 
 config ARCH_BCMRING
 	bool "Broadcom BCMRING"
@@ -528,28 +528,6 @@
 	help
 	  Support for Intel's IOP33X (XScale) family of processors.
 
-config ARCH_IXP23XX
- 	bool "IXP23XX-based"
-	depends on MMU
-	select CPU_XSC3
- 	select PCI
-	select ARCH_USES_GETTIMEOFFSET
-	select NEED_MACH_IO_H
-	select NEED_MACH_MEMORY_H
-	help
-	  Support for Intel's IXP23xx (XScale) family of processors.
-
-config ARCH_IXP2000
-	bool "IXP2400/2800-based"
-	depends on MMU
-	select CPU_XSCALE
-	select PCI
-	select ARCH_USES_GETTIMEOFFSET
-	select NEED_MACH_IO_H
-	select NEED_MACH_MEMORY_H
-	help
-	  Support for Intel's IXP2400/2800 (XScale) family of processors.
-
 config ARCH_IXP4XX
 	bool "IXP4xx-based"
 	depends on MMU
@@ -1046,10 +1024,6 @@
 
 source "arch/arm/mach-ixp4xx/Kconfig"
 
-source "arch/arm/mach-ixp2000/Kconfig"
-
-source "arch/arm/mach-ixp23xx/Kconfig"
-
 source "arch/arm/mach-kirkwood/Kconfig"
 
 source "arch/arm/mach-ks8695/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 047a207..a0c40a0 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -149,8 +149,6 @@
 machine-$(CONFIG_ARCH_IOP13XX)		:= iop13xx
 machine-$(CONFIG_ARCH_IOP32X)		:= iop32x
 machine-$(CONFIG_ARCH_IOP33X)		:= iop33x
-machine-$(CONFIG_ARCH_IXP2000)		:= ixp2000
-machine-$(CONFIG_ARCH_IXP23XX)		:= ixp23xx
 machine-$(CONFIG_ARCH_IXP4XX)		:= ixp4xx
 machine-$(CONFIG_ARCH_KIRKWOOD)		:= kirkwood
 machine-$(CONFIG_ARCH_KS8695)		:= ks8695
diff --git a/arch/arm/boot/compressed/head-xscale.S b/arch/arm/boot/compressed/head-xscale.S
index aa5ee49..6ab0599 100644
--- a/arch/arm/boot/compressed/head-xscale.S
+++ b/arch/arm/boot/compressed/head-xscale.S
@@ -32,10 +32,3 @@
 		bic	r0, r0, #0x1000		@ clear Icache
 		mcr	p15, 0, r0, c1, c0, 0
 
-#ifdef CONFIG_ARCH_IXP2000
-		mov	r1, #-1
-		mov	r0, #0xd6000000
-		str	r1, [r0, #0x14]
-		str	r1, [r0, #0x18]
-#endif
-
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index 215816f..e8a4e58 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -11,7 +11,5 @@
 obj-$(CONFIG_SHARP_LOCOMO)	+= locomo.o
 obj-$(CONFIG_SHARP_PARAM)	+= sharpsl_param.o
 obj-$(CONFIG_SHARP_SCOOP)	+= scoop.o
-obj-$(CONFIG_ARCH_IXP2000)	+= uengine.o
-obj-$(CONFIG_ARCH_IXP23XX)	+= uengine.o
 obj-$(CONFIG_PCI_HOST_ITE8152)  += it8152.o
 obj-$(CONFIG_ARM_TIMER_SP804)	+= timer-sp.o
diff --git a/arch/arm/common/uengine.c b/arch/arm/common/uengine.c
deleted file mode 100644
index bef408f..0000000
--- a/arch/arm/common/uengine.c
+++ /dev/null
@@ -1,507 +0,0 @@
-/*
- * Generic library functions for the microengines found on the Intel
- * IXP2000 series of network processors.
- *
- * Copyright (C) 2004, 2005 Lennert Buytenhek <buytenh@wantstofly.org>
- * Dedicated to Marija Kulikova.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU Lesser General Public License as
- * published by the Free Software Foundation; either version 2.1 of the
- * License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/hardware/uengine.h>
-
-#if defined(CONFIG_ARCH_IXP2000)
-#define IXP_UENGINE_CSR_VIRT_BASE	IXP2000_UENGINE_CSR_VIRT_BASE
-#define IXP_PRODUCT_ID			IXP2000_PRODUCT_ID
-#define IXP_MISC_CONTROL		IXP2000_MISC_CONTROL
-#define IXP_RESET1			IXP2000_RESET1
-#else
-#if defined(CONFIG_ARCH_IXP23XX)
-#define IXP_UENGINE_CSR_VIRT_BASE	IXP23XX_UENGINE_CSR_VIRT_BASE
-#define IXP_PRODUCT_ID			IXP23XX_PRODUCT_ID
-#define IXP_MISC_CONTROL		IXP23XX_MISC_CONTROL
-#define IXP_RESET1			IXP23XX_RESET1
-#else
-#error unknown platform
-#endif
-#endif
-
-#define USTORE_ADDRESS			0x000
-#define USTORE_DATA_LOWER		0x004
-#define USTORE_DATA_UPPER		0x008
-#define CTX_ENABLES			0x018
-#define CC_ENABLE			0x01c
-#define CSR_CTX_POINTER			0x020
-#define INDIRECT_CTX_STS		0x040
-#define ACTIVE_CTX_STS			0x044
-#define INDIRECT_CTX_SIG_EVENTS		0x048
-#define INDIRECT_CTX_WAKEUP_EVENTS	0x050
-#define NN_PUT				0x080
-#define NN_GET				0x084
-#define TIMESTAMP_LOW			0x0c0
-#define TIMESTAMP_HIGH			0x0c4
-#define T_INDEX_BYTE_INDEX		0x0f4
-#define LOCAL_CSR_STATUS		0x180
-
-u32 ixp2000_uengine_mask;
-
-static void *ixp2000_uengine_csr_area(int uengine)
-{
-	return ((void *)IXP_UENGINE_CSR_VIRT_BASE) + (uengine << 10);
-}
-
-/*
- * LOCAL_CSR_STATUS=1 after a read or write to a microengine's CSR
- * space means that the microengine we tried to access was also trying
- * to access its own CSR space on the same clock cycle as we did.  When
- * this happens, we lose the arbitration process by default, and the
- * read or write we tried to do was not actually performed, so we try
- * again until it succeeds.
- */
-u32 ixp2000_uengine_csr_read(int uengine, int offset)
-{
-	void *uebase;
-	u32 *local_csr_status;
-	u32 *reg;
-	u32 value;
-
-	uebase = ixp2000_uengine_csr_area(uengine);
-
-	local_csr_status = (u32 *)(uebase + LOCAL_CSR_STATUS);
-	reg = (u32 *)(uebase + offset);
-	do {
-		value = ixp2000_reg_read(reg);
-	} while (ixp2000_reg_read(local_csr_status) & 1);
-
-	return value;
-}
-EXPORT_SYMBOL(ixp2000_uengine_csr_read);
-
-void ixp2000_uengine_csr_write(int uengine, int offset, u32 value)
-{
-	void *uebase;
-	u32 *local_csr_status;
-	u32 *reg;
-
-	uebase = ixp2000_uengine_csr_area(uengine);
-
-	local_csr_status = (u32 *)(uebase + LOCAL_CSR_STATUS);
-	reg = (u32 *)(uebase + offset);
-	do {
-		ixp2000_reg_write(reg, value);
-	} while (ixp2000_reg_read(local_csr_status) & 1);
-}
-EXPORT_SYMBOL(ixp2000_uengine_csr_write);
-
-void ixp2000_uengine_reset(u32 uengine_mask)
-{
-	u32 value;
-
-	value = ixp2000_reg_read(IXP_RESET1) & ~ixp2000_uengine_mask;
-
-	uengine_mask &= ixp2000_uengine_mask;
-	ixp2000_reg_wrb(IXP_RESET1, value | uengine_mask);
-	ixp2000_reg_wrb(IXP_RESET1, value);
-}
-EXPORT_SYMBOL(ixp2000_uengine_reset);
-
-void ixp2000_uengine_set_mode(int uengine, u32 mode)
-{
-	/*
-	 * CTL_STR_PAR_EN: unconditionally enable parity checking on
-	 * control store.
-	 */
-	mode |= 0x10000000;
-	ixp2000_uengine_csr_write(uengine, CTX_ENABLES, mode);
-
-	/*
-	 * Enable updating of condition codes.
-	 */
-	ixp2000_uengine_csr_write(uengine, CC_ENABLE, 0x00002000);
-
-	/*
-	 * Initialise other per-microengine registers.
-	 */
-	ixp2000_uengine_csr_write(uengine, NN_PUT, 0x00);
-	ixp2000_uengine_csr_write(uengine, NN_GET, 0x00);
-	ixp2000_uengine_csr_write(uengine, T_INDEX_BYTE_INDEX, 0);
-}
-EXPORT_SYMBOL(ixp2000_uengine_set_mode);
-
-static int make_even_parity(u32 x)
-{
-	return hweight32(x) & 1;
-}
-
-static void ustore_write(int uengine, u64 insn)
-{
-	/*
-	 * Generate even parity for top and bottom 20 bits.
-	 */
-	insn |= (u64)make_even_parity((insn >> 20) & 0x000fffff) << 41;
-	insn |= (u64)make_even_parity(insn & 0x000fffff) << 40;
-
-	/*
-	 * Write to microstore.  The second write auto-increments
-	 * the USTORE_ADDRESS index register.
-	 */
-	ixp2000_uengine_csr_write(uengine, USTORE_DATA_LOWER, (u32)insn);
-	ixp2000_uengine_csr_write(uengine, USTORE_DATA_UPPER, (u32)(insn >> 32));
-}
-
-void ixp2000_uengine_load_microcode(int uengine, u8 *ucode, int insns)
-{
-	int i;
-
-	/*
-	 * Start writing to microstore at address 0.
-	 */
-	ixp2000_uengine_csr_write(uengine, USTORE_ADDRESS, 0x80000000);
-	for (i = 0; i < insns; i++) {
-		u64 insn;
-
-		insn = (((u64)ucode[0]) << 32) |
-			(((u64)ucode[1]) << 24) |
-			(((u64)ucode[2]) << 16) |
-			(((u64)ucode[3]) << 8) |
-			((u64)ucode[4]);
-		ucode += 5;
-
-		ustore_write(uengine, insn);
-	}
-
-	/*
- 	 * Pad with a few NOPs at the end (to avoid the microengine
-	 * aborting as it prefetches beyond the last instruction), unless
-	 * we run off the end of the instruction store first, at which
-	 * point the address register will wrap back to zero.
-	 */
-	for (i = 0; i < 4; i++) {
-		u32 addr;
-
-		addr = ixp2000_uengine_csr_read(uengine, USTORE_ADDRESS);
-		if (addr == 0x80000000)
-			break;
-		ustore_write(uengine, 0xf0000c0300ULL);
-	}
-
-	/*
-	 * End programming.
-	 */
-	ixp2000_uengine_csr_write(uengine, USTORE_ADDRESS, 0x00000000);
-}
-EXPORT_SYMBOL(ixp2000_uengine_load_microcode);
-
-void ixp2000_uengine_init_context(int uengine, int context, int pc)
-{
-	/*
-	 * Select the right context for indirect access.
-	 */
-	ixp2000_uengine_csr_write(uengine, CSR_CTX_POINTER, context);
-
-	/*
-	 * Initialise signal masks to immediately go to Ready state.
-	 */
-	ixp2000_uengine_csr_write(uengine, INDIRECT_CTX_SIG_EVENTS, 1);
-	ixp2000_uengine_csr_write(uengine, INDIRECT_CTX_WAKEUP_EVENTS, 1);
-
-	/*
-	 * Set program counter.
-	 */
-	ixp2000_uengine_csr_write(uengine, INDIRECT_CTX_STS, pc);
-}
-EXPORT_SYMBOL(ixp2000_uengine_init_context);
-
-void ixp2000_uengine_start_contexts(int uengine, u8 ctx_mask)
-{
-	u32 mask;
-
-	/*
-	 * Enable the specified context to go to Executing state.
-	 */
-	mask = ixp2000_uengine_csr_read(uengine, CTX_ENABLES);
-	mask |= ctx_mask << 8;
-	ixp2000_uengine_csr_write(uengine, CTX_ENABLES, mask);
-}
-EXPORT_SYMBOL(ixp2000_uengine_start_contexts);
-
-void ixp2000_uengine_stop_contexts(int uengine, u8 ctx_mask)
-{
-	u32 mask;
-
-	/*
-	 * Disable the Ready->Executing transition.  Note that this
-	 * does not stop the context until it voluntarily yields.
-	 */
-	mask = ixp2000_uengine_csr_read(uengine, CTX_ENABLES);
-	mask &= ~(ctx_mask << 8);
-	ixp2000_uengine_csr_write(uengine, CTX_ENABLES, mask);
-}
-EXPORT_SYMBOL(ixp2000_uengine_stop_contexts);
-
-static int check_ixp_type(struct ixp2000_uengine_code *c)
-{
-	u32 product_id;
-	u32 rev;
-
-	product_id = ixp2000_reg_read(IXP_PRODUCT_ID);
-	if (((product_id >> 16) & 0x1f) != 0)
-		return 0;
-
-	switch ((product_id >> 8) & 0xff) {
-#ifdef CONFIG_ARCH_IXP2000
-	case 0:		/* IXP2800 */
-		if (!(c->cpu_model_bitmask & 4))
-			return 0;
-		break;
-
-	case 1:		/* IXP2850 */
-		if (!(c->cpu_model_bitmask & 8))
-			return 0;
-		break;
-
-	case 2:		/* IXP2400 */
-		if (!(c->cpu_model_bitmask & 2))
-			return 0;
-		break;
-#endif
-
-#ifdef CONFIG_ARCH_IXP23XX
-	case 4:		/* IXP23xx */
-		if (!(c->cpu_model_bitmask & 0x3f0))
-			return 0;
-		break;
-#endif
-
-	default:
-		return 0;
-	}
-
-	rev = product_id & 0xff;
-	if (rev < c->cpu_min_revision || rev > c->cpu_max_revision)
-		return 0;
-
-	return 1;
-}
-
-static void generate_ucode(u8 *ucode, u32 *gpr_a, u32 *gpr_b)
-{
-	int offset;
-	int i;
-
-	offset = 0;
-
-	for (i = 0; i < 128; i++) {
-		u8 b3;
-		u8 b2;
-		u8 b1;
-		u8 b0;
-
-		b3 = (gpr_a[i] >> 24) & 0xff;
-		b2 = (gpr_a[i] >> 16) & 0xff;
-		b1 = (gpr_a[i] >> 8) & 0xff;
-		b0 = gpr_a[i] & 0xff;
-
-		/* immed[@ai, (b1 << 8) | b0] */
-		/* 11110000 0000VVVV VVVV11VV VVVVVV00 1IIIIIII */
-		ucode[offset++] = 0xf0;
-		ucode[offset++] = (b1 >> 4);
-		ucode[offset++] = (b1 << 4) | 0x0c | (b0 >> 6);
-		ucode[offset++] = (b0 << 2);
-		ucode[offset++] = 0x80 | i;
-
-		/* immed_w1[@ai, (b3 << 8) | b2] */
-		/* 11110100 0100VVVV VVVV11VV VVVVVV00 1IIIIIII */
-		ucode[offset++] = 0xf4;
-		ucode[offset++] = 0x40 | (b3 >> 4);
-		ucode[offset++] = (b3 << 4) | 0x0c | (b2 >> 6);
-		ucode[offset++] = (b2 << 2);
-		ucode[offset++] = 0x80 | i;
-	}
-
-	for (i = 0; i < 128; i++) {
-		u8 b3;
-		u8 b2;
-		u8 b1;
-		u8 b0;
-
-		b3 = (gpr_b[i] >> 24) & 0xff;
-		b2 = (gpr_b[i] >> 16) & 0xff;
-		b1 = (gpr_b[i] >> 8) & 0xff;
-		b0 = gpr_b[i] & 0xff;
-
-		/* immed[@bi, (b1 << 8) | b0] */
-		/* 11110000 0000VVVV VVVV001I IIIIII11 VVVVVVVV */
-		ucode[offset++] = 0xf0;
-		ucode[offset++] = (b1 >> 4);
-		ucode[offset++] = (b1 << 4) | 0x02 | (i >> 6);
-		ucode[offset++] = (i << 2) | 0x03;
-		ucode[offset++] = b0;
-
-		/* immed_w1[@bi, (b3 << 8) | b2] */
-		/* 11110100 0100VVVV VVVV001I IIIIII11 VVVVVVVV */
-		ucode[offset++] = 0xf4;
-		ucode[offset++] = 0x40 | (b3 >> 4);
-		ucode[offset++] = (b3 << 4) | 0x02 | (i >> 6);
-		ucode[offset++] = (i << 2) | 0x03;
-		ucode[offset++] = b2;
-	}
-
-	/* ctx_arb[kill] */
-	ucode[offset++] = 0xe0;
-	ucode[offset++] = 0x00;
-	ucode[offset++] = 0x01;
-	ucode[offset++] = 0x00;
-	ucode[offset++] = 0x00;
-}
-
-static int set_initial_registers(int uengine, struct ixp2000_uengine_code *c)
-{
-	int per_ctx_regs;
-	u32 *gpr_a;
-	u32 *gpr_b;
-	u8 *ucode;
-	int i;
-
-	gpr_a = kzalloc(128 * sizeof(u32), GFP_KERNEL);
-	gpr_b = kzalloc(128 * sizeof(u32), GFP_KERNEL);
-	ucode = kmalloc(513 * 5, GFP_KERNEL);
-	if (gpr_a == NULL || gpr_b == NULL || ucode == NULL) {
-		kfree(ucode);
-		kfree(gpr_b);
-		kfree(gpr_a);
-		return 1;
-	}
-
-	per_ctx_regs = 16;
-	if (c->uengine_parameters & IXP2000_UENGINE_4_CONTEXTS)
-		per_ctx_regs = 32;
-
-	for (i = 0; i < 256; i++) {
-		struct ixp2000_reg_value *r = c->initial_reg_values + i;
-		u32 *bank;
-		int inc;
-		int j;
-
-		if (r->reg == -1)
-			break;
-
-		bank = (r->reg & 0x400) ? gpr_b : gpr_a;
-		inc = (r->reg & 0x80) ? 128 : per_ctx_regs;
-
-		j = r->reg & 0x7f;
-		while (j < 128) {
-			bank[j] = r->value;
-			j += inc;
-		}
-	}
-
-	generate_ucode(ucode, gpr_a, gpr_b);
-	ixp2000_uengine_load_microcode(uengine, ucode, 513);
-	ixp2000_uengine_init_context(uengine, 0, 0);
-	ixp2000_uengine_start_contexts(uengine, 0x01);
-	for (i = 0; i < 100; i++) {
-		u32 status;
-
-		status = ixp2000_uengine_csr_read(uengine, ACTIVE_CTX_STS);
-		if (!(status & 0x80000000))
-			break;
-	}
-	ixp2000_uengine_stop_contexts(uengine, 0x01);
-
-	kfree(ucode);
-	kfree(gpr_b);
-	kfree(gpr_a);
-
-	return !!(i == 100);
-}
-
-int ixp2000_uengine_load(int uengine, struct ixp2000_uengine_code *c)
-{
-	int ctx;
-
-	if (!check_ixp_type(c))
-		return 1;
-
-	if (!(ixp2000_uengine_mask & (1 << uengine)))
-		return 1;
-
-	ixp2000_uengine_reset(1 << uengine);
-	ixp2000_uengine_set_mode(uengine, c->uengine_parameters);
-	if (set_initial_registers(uengine, c))
-		return 1;
-	ixp2000_uengine_load_microcode(uengine, c->insns, c->num_insns);
-
-	for (ctx = 0; ctx < 8; ctx++)
-		ixp2000_uengine_init_context(uengine, ctx, 0);
-
-	return 0;
-}
-EXPORT_SYMBOL(ixp2000_uengine_load);
-
-
-static int __init ixp2000_uengine_init(void)
-{
-	int uengine;
-	u32 value;
-
-	/*
-	 * Determine number of microengines present.
-	 */
-	switch ((ixp2000_reg_read(IXP_PRODUCT_ID) >> 8) & 0x1fff) {
-#ifdef CONFIG_ARCH_IXP2000
-	case 0:		/* IXP2800 */
-	case 1:		/* IXP2850 */
-		ixp2000_uengine_mask = 0x00ff00ff;
-		break;
-
-	case 2:		/* IXP2400 */
-		ixp2000_uengine_mask = 0x000f000f;
-		break;
-#endif
-
-#ifdef CONFIG_ARCH_IXP23XX
-	case 4:		/* IXP23xx */
-		ixp2000_uengine_mask = (*IXP23XX_EXP_CFG_FUSE >> 8) & 0xf;
-		break;
-#endif
-
-	default:
-		printk(KERN_INFO "Detected unknown IXP2000 model (%.8x)\n",
-			(unsigned int)ixp2000_reg_read(IXP_PRODUCT_ID));
-		ixp2000_uengine_mask = 0x00000000;
-		break;
-	}
-
-	/*
-	 * Reset microengines.
-	 */
-	ixp2000_uengine_reset(ixp2000_uengine_mask);
-
-	/*
-	 * Synchronise timestamp counters across all microengines.
-	 */
-	value = ixp2000_reg_read(IXP_MISC_CONTROL);
-	ixp2000_reg_wrb(IXP_MISC_CONTROL, value & ~0x80);
-	for (uengine = 0; uengine < 32; uengine++) {
-		if (ixp2000_uengine_mask & (1 << uengine)) {
-			ixp2000_uengine_csr_write(uengine, TIMESTAMP_LOW, 0);
-			ixp2000_uengine_csr_write(uengine, TIMESTAMP_HIGH, 0);
-		}
-	}
-	ixp2000_reg_wrb(IXP_MISC_CONTROL, value | 0x80);
-
-	return 0;
-}
-
-subsys_initcall(ixp2000_uengine_init);
diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig
new file mode 100644
index 0000000..67bc571
--- /dev/null
+++ b/arch/arm/configs/at91_dt_defconfig
@@ -0,0 +1,196 @@
+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_AT91SAM9260=y
+CONFIG_SOC_AT91SAM9263=y
+CONFIG_SOC_AT91SAM9G45=y
+CONFIG_SOC_AT91SAM9X5=y
+CONFIG_MACH_AT91SAM_DT=y
+CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
+CONFIG_AT91_TIMER_HZ=128
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_LEDS=y
+CONFIG_LEDS_CPU=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_CMDLINE="mem=128M console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_AUTO_ZRELADDR=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+CONFIG_IPV6=y
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_PWM=y
+CONFIG_ATMEL_TCLIB=y
+CONFIG_EEPROM_93CX6=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_DAVICOM_PHY=y
+CONFIG_MICREL_PHY=y
+# CONFIG_WLAN is not set
+CONFIG_INPUT_POLLDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=480
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=272
+CONFIG_INPUT_JOYDEV=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATMEL=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_SSB=m
+CONFIG_FB=y
+CONFIG_FB_MODE_HELPERS=y
+CONFIG_FB_ATMEL=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_ATMEL_LCDC=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_FONT_MINI_4x6=y
+CONFIG_LOGO=y
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_ACM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_AT91=m
+CONFIG_USB_ATMEL_USBA=m
+CONFIG_USB_ETH=m
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_CDC_COMPOSITE=m
+CONFIG_USB_G_ACM_MS=m
+CONFIG_USB_G_MULTI=m
+CONFIG_USB_G_MULTI_CDC=y
+CONFIG_MMC=y
+CONFIG_MMC_ATMELMCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_RTC_DRV_AT91SAM9=y
+CONFIG_DMADEVICES=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_ARC4=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_CCITT=m
+CONFIG_CRC_ITU_T=m
+CONFIG_CRC7=m
+CONFIG_AVERAGE=y
diff --git a/arch/arm/configs/at91rm9200_defconfig b/arch/arm/configs/at91rm9200_defconfig
index bbe4e1a..d54e2ac 100644
--- a/arch/arm/configs/at91rm9200_defconfig
+++ b/arch/arm/configs/at91rm9200_defconfig
@@ -14,6 +14,7 @@
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_IOSCHED_CFQ is not set
 CONFIG_ARCH_AT91=y
+CONFIG_ARCH_AT91RM9200=y
 CONFIG_MACH_ONEARM=y
 CONFIG_ARCH_AT91RM9200DK=y
 CONFIG_MACH_AT91RM9200EK=y
diff --git a/arch/arm/configs/ixp2000_defconfig b/arch/arm/configs/ixp2000_defconfig
deleted file mode 100644
index 8405ade..0000000
--- a/arch/arm/configs/ixp2000_defconfig
+++ /dev/null
@@ -1,99 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_HOTPLUG is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_ARCH_IXP2000=y
-CONFIG_ARCH_ENP2611=y
-CONFIG_ARCH_IXDP2400=y
-CONFIG_ARCH_IXDP2800=y
-CONFIG_ARCH_IXDP2401=y
-CONFIG_ARCH_IXDP2801=y
-# CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO is not set
-# CONFIG_ARM_THUMB is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,57600 root=/dev/nfs ip=bootp mem=64M@0x0"
-CONFIG_FPE_NWFPE=y
-CONFIG_FPE_NWFPE_XP=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_SYN_COOKIES=y
-CONFIG_IPV6=y
-# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET6_XFRM_MODE_BEET is not set
-# CONFIG_IPV6_SIT is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_MTD_REDBOOT_PARTS_READONLY=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_IXP2000=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_NBD=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_EEPROM_LEGACY=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_CS89x0=y
-CONFIG_E100=y
-CONFIG_ENP2611_MSF_NET=y
-CONFIG_WAN=y
-CONFIG_HDLC=y
-CONFIG_HDLC_RAW=y
-CONFIG_HDLC_CISCO=y
-CONFIG_HDLC_FR=y
-CONFIG_HDLC_PPP=y
-CONFIG_DLCI=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=3
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_IXP2000=y
-CONFIG_WATCHDOG=y
-CONFIG_IXP2000_WATCHDOG=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_INOTIFY=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_MUTEXES=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/ixp23xx_defconfig b/arch/arm/configs/ixp23xx_defconfig
deleted file mode 100644
index 6887176..0000000
--- a/arch/arm/configs/ixp23xx_defconfig
+++ /dev/null
@@ -1,105 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_ARCH_IXP23XX=y
-CONFIG_MACH_ESPRESSO=y
-CONFIG_MACH_IXDP2351=y
-CONFIG_MACH_ROADRUNNER=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs ip=bootp"
-CONFIG_FPE_NWFPE=y
-CONFIG_FPE_NWFPE_XP=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_SYN_COOKIES=y
-CONFIG_IPV6=y
-# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET6_XFRM_MODE_BEET is not set
-# CONFIG_IPV6_SIT is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-# CONFIG_FW_LOADER is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_MTD_REDBOOT_PARTS_READONLY=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_NBD=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_EEPROM_LEGACY=y
-CONFIG_IDE=y
-CONFIG_BLK_DEV_SIIMAGE=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_E100=y
-CONFIG_E1000=y
-CONFIG_WAN=y
-CONFIG_HDLC=y
-CONFIG_HDLC_RAW=y
-CONFIG_HDLC_CISCO=y
-CONFIG_HDLC_FR=y
-CONFIG_HDLC_PPP=y
-CONFIG_DLCI=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_WATCHDOG=y
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_UHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_INOTIFY=y
-CONFIG_MSDOS_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_MUTEXES=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
diff --git a/arch/arm/include/asm/hardware/uengine.h b/arch/arm/include/asm/hardware/uengine.h
deleted file mode 100644
index b442d65..0000000
--- a/arch/arm/include/asm/hardware/uengine.h
+++ /dev/null
@@ -1,62 +0,0 @@
-/*
- * Generic library functions for the microengines found on the Intel
- * IXP2000 series of network processors.
- *
- * Copyright (C) 2004, 2005 Lennert Buytenhek <buytenh@wantstofly.org>
- * Dedicated to Marija Kulikova.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU Lesser General Public License as
- * published by the Free Software Foundation; either version 2.1 of the
- * License, or (at your option) any later version.
- */
-
-#ifndef __IXP2000_UENGINE_H
-#define __IXP2000_UENGINE_H
-
-extern u32 ixp2000_uengine_mask;
-
-struct ixp2000_uengine_code
-{
-	u32	cpu_model_bitmask;
-	u8	cpu_min_revision;
-	u8	cpu_max_revision;
-
-	u32	uengine_parameters;
-
-	struct ixp2000_reg_value {
-		int	reg;
-		u32	value;
-	} *initial_reg_values;
-
-	int	num_insns;
-	u8	*insns;
-};
-
-u32 ixp2000_uengine_csr_read(int uengine, int offset);
-void ixp2000_uengine_csr_write(int uengine, int offset, u32 value);
-void ixp2000_uengine_reset(u32 uengine_mask);
-void ixp2000_uengine_set_mode(int uengine, u32 mode);
-void ixp2000_uengine_load_microcode(int uengine, u8 *ucode, int insns);
-void ixp2000_uengine_init_context(int uengine, int context, int pc);
-void ixp2000_uengine_start_contexts(int uengine, u8 ctx_mask);
-void ixp2000_uengine_stop_contexts(int uengine, u8 ctx_mask);
-int ixp2000_uengine_load(int uengine, struct ixp2000_uengine_code *c);
-
-#define IXP2000_UENGINE_8_CONTEXTS		0x00000000
-#define IXP2000_UENGINE_4_CONTEXTS		0x80000000
-#define IXP2000_UENGINE_PRN_UPDATE_EVERY	0x40000000
-#define IXP2000_UENGINE_PRN_UPDATE_ON_ACCESS	0x00000000
-#define IXP2000_UENGINE_NN_FROM_SELF		0x00100000
-#define IXP2000_UENGINE_NN_FROM_PREVIOUS	0x00000000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_3	0x000c0000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_2	0x00080000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_1	0x00040000
-#define IXP2000_UENGINE_ASSERT_EMPTY_AT_0	0x00000000
-#define IXP2000_UENGINE_LM_ADDR1_GLOBAL		0x00020000
-#define IXP2000_UENGINE_LM_ADDR1_PER_CONTEXT	0x00000000
-#define IXP2000_UENGINE_LM_ADDR0_GLOBAL		0x00010000
-#define IXP2000_UENGINE_LM_ADDR0_PER_CONTEXT	0x00000000
-
-
-#endif
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 45db05d..98a42f3 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -9,15 +9,6 @@
 config HAVE_AT91_DBGU1
 	bool
 
-config HAVE_AT91_USART3
-	bool
-
-config HAVE_AT91_USART4
-	bool
-
-config HAVE_AT91_USART5
-	bool
-
 config AT91_SAM9_ALT_RESET
 	bool
 	default !ARCH_AT91X40
@@ -26,87 +17,121 @@
 	bool
 	default !ARCH_AT91X40
 
+config SOC_AT91SAM9
+	bool
+	select GENERIC_CLOCKEVENTS
+	select CPU_ARM926T
+
 menu "Atmel AT91 System-on-Chip"
 
-choice
-	prompt "Atmel AT91 Processor"
+comment "Atmel AT91 Processor"
 
-config ARCH_AT91RM9200
+config SOC_AT91SAM9
+	bool
+	select CPU_ARM926T
+	select AT91_SAM9_TIME
+	select AT91_SAM9_SMC
+
+config SOC_AT91RM9200
 	bool "AT91RM9200"
 	select CPU_ARM920T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_DBGU0
-	select HAVE_AT91_USART3
+
+config SOC_AT91SAM9260
+	bool "AT91SAM9260, AT91SAM9XE or AT91SAM9G20"
+	select SOC_AT91SAM9
+	select HAVE_AT91_DBGU0
+	select HAVE_NET_MACB
+	help
+	  Select this if you are using one of Atmel's AT91SAM9260, AT91SAM9XE
+	  or AT91SAM9G20 SoC.
+
+config SOC_AT91SAM9261
+	bool "AT91SAM9261 or AT91SAM9G10"
+	select SOC_AT91SAM9
+	select HAVE_AT91_DBGU0
+	select HAVE_FB_ATMEL
+	help
+	  Select this if you are using one of Atmel's AT91SAM9261 or AT91SAM9G10 SoC.
+
+config SOC_AT91SAM9263
+	bool "AT91SAM9263"
+	select SOC_AT91SAM9
+	select HAVE_AT91_DBGU1
+	select HAVE_FB_ATMEL
+	select HAVE_NET_MACB
+
+config SOC_AT91SAM9RL
+	bool "AT91SAM9RL"
+	select SOC_AT91SAM9
+	select HAVE_AT91_DBGU0
+	select HAVE_FB_ATMEL
+
+config SOC_AT91SAM9G45
+	bool "AT91SAM9G45 or AT91SAM9M10 families"
+	select SOC_AT91SAM9
+	select HAVE_AT91_DBGU1
+	select HAVE_FB_ATMEL
+	select HAVE_NET_MACB
+	help
+	  Select this if you are using one of Atmel's AT91SAM9G45 family SoC.
+	  This support covers AT91SAM9G45, AT91SAM9G46, AT91SAM9M10 and AT91SAM9M11.
+
+config SOC_AT91SAM9X5
+	bool "AT91SAM9x5 family"
+	select SOC_AT91SAM9
+	select HAVE_AT91_DBGU0
+	select HAVE_FB_ATMEL
+	select HAVE_NET_MACB
+	help
+	  Select this if you are using one of Atmel's AT91SAM9x5 family SoC.
+	  This means that your SAM9 name finishes with a '5' (except if it is
+	  AT91SAM9G45!).
+	  This support covers AT91SAM9G15, AT91SAM9G25, AT91SAM9X25, AT91SAM9G35
+	  and AT91SAM9X35.
+
+choice
+	prompt "Atmel AT91 Processor Devices for non DT boards"
+
+config ARCH_AT91_NONE
+	bool "None"
+
+config ARCH_AT91RM9200
+	bool "AT91RM9200"
+	select SOC_AT91RM9200
 
 config ARCH_AT91SAM9260
 	bool "AT91SAM9260 or AT91SAM9XE"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_AT91_DBGU0
-	select HAVE_AT91_USART3
-	select HAVE_AT91_USART4
-	select HAVE_AT91_USART5
-	select HAVE_NET_MACB
+	select SOC_AT91SAM9260
 
 config ARCH_AT91SAM9261
 	bool "AT91SAM9261"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_FB_ATMEL
-	select HAVE_AT91_DBGU0
+	select SOC_AT91SAM9261
 
 config ARCH_AT91SAM9G10
 	bool "AT91SAM9G10"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_AT91_DBGU0
-	select HAVE_FB_ATMEL
+	select SOC_AT91SAM9261
 
 config ARCH_AT91SAM9263
 	bool "AT91SAM9263"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_FB_ATMEL
-	select HAVE_NET_MACB
-	select HAVE_AT91_DBGU1
+	select SOC_AT91SAM9263
 
 config ARCH_AT91SAM9RL
 	bool "AT91SAM9RL"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_AT91_USART3
-	select HAVE_FB_ATMEL
-	select HAVE_AT91_DBGU0
+	select SOC_AT91SAM9RL
 
 config ARCH_AT91SAM9G20
 	bool "AT91SAM9G20"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_AT91_DBGU0
-	select HAVE_AT91_USART3
-	select HAVE_AT91_USART4
-	select HAVE_AT91_USART5
-	select HAVE_NET_MACB
+	select SOC_AT91SAM9260
 
 config ARCH_AT91SAM9G45
 	bool "AT91SAM9G45"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_AT91_USART3
-	select HAVE_FB_ATMEL
-	select HAVE_NET_MACB
-	select HAVE_AT91_DBGU1
-
-config ARCH_AT91SAM9X5
-	bool "AT91SAM9x5 family"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-	select HAVE_FB_ATMEL
-	select HAVE_NET_MACB
-	select HAVE_AT91_DBGU0
+	select SOC_AT91SAM9G45
 
 config ARCH_AT91X40
 	bool "AT91x40"
+	depends on !MMU
 	select ARCH_USES_GETTIMEOFFSET
 
 endchoice
@@ -364,6 +389,7 @@
 	  Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
 	  with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and
 	  onwards.
+	  <http://www.atmel.com/tools/SAM9G20-EK.aspx>
 
 config MACH_CPU9G20
 	bool "Eukrea CPU9G20 board"
@@ -433,9 +459,10 @@
 config MACH_AT91SAM9M10G45EK
 	bool "Atmel AT91SAM9M10G45-EK Evaluation Kits"
 	help
-	  Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit.
-	  "ES" at the end of the name means that this board is an
-	  Engineering Sample.
+	  Select this if you are using Atmel's AT91SAM9M10G45-EK Evaluation Kit.
+	  Those boards can be populated with any SoC of AT91SAM9G45 or AT91SAM9M10
+	  families: AT91SAM9G45, AT91SAM9G46, AT91SAM9M10 and AT91SAM9M11.
+	  <http://www.atmel.com/tools/SAM9M10-G45-EK.aspx>
 
 endif
 
@@ -515,41 +542,6 @@
 	  system clock (of at least several MHz), rounding is less of a
 	  problem so it can be safer to use a decimal values like 100.
 
-choice
-	prompt "Select a UART for early kernel messages"
-
-config AT91_EARLY_DBGU0
-	bool "DBGU on rm9200, 9260/9g20, 9261/9g10 and 9rl"
-	depends on HAVE_AT91_DBGU0
-
-config AT91_EARLY_DBGU1
-	bool "DBGU on 9263 and 9g45"
-	depends on HAVE_AT91_DBGU1
-
-config AT91_EARLY_USART0
-	bool "USART0"
-
-config AT91_EARLY_USART1
-	bool "USART1"
-
-config AT91_EARLY_USART2
-	bool "USART2"
-	depends on ! ARCH_AT91X40
-
-config AT91_EARLY_USART3
-	bool "USART3"
-	depends on HAVE_AT91_USART3
-
-config AT91_EARLY_USART4
-	bool "USART4"
-	depends on HAVE_AT91_USART4
-
-config AT91_EARLY_USART5
-	bool "USART5"
-	depends on HAVE_AT91_USART5
-
-endchoice
-
 endmenu
 
 endif
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 8512e53..79d0f60 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -10,17 +10,25 @@
 obj-$(CONFIG_AT91_PMC_UNIT)	+= clock.o
 obj-$(CONFIG_AT91_SAM9_ALT_RESET) += at91sam9_alt_reset.o
 obj-$(CONFIG_AT91_SAM9G45_RESET) += at91sam9g45_reset.o
+obj-$(CONFIG_SOC_AT91SAM9)	+= at91sam926x_time.o sam9_smc.o
 
 # CPU-specific support
-obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200.o at91rm9200_time.o at91rm9200_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9G10)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9G45)	+= at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT91SAM9X5)	+= at91sam9x5.o at91sam926x_time.o sam9_smc.o
+obj-$(CONFIG_SOC_AT91RM9200)	+= at91rm9200.o at91rm9200_time.o
+obj-$(CONFIG_SOC_AT91SAM9260)	+= at91sam9260.o
+obj-$(CONFIG_SOC_AT91SAM9261)	+= at91sam9261.o
+obj-$(CONFIG_SOC_AT91SAM9263)	+= at91sam9263.o
+obj-$(CONFIG_SOC_AT91SAM9G45)	+= at91sam9g45.o
+obj-$(CONFIG_SOC_AT91SAM9X5)	+= at91sam9x5.o
+obj-$(CONFIG_SOC_AT91SAM9RL)	+= at91sam9rl.o
+
+obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9G10)	+= at91sam9261_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9G45)	+= at91sam9g45_devices.o
 obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o
 
 # AT91RM9200 board-specific support
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index 364c193..d50da1a 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -258,18 +258,6 @@
 	clk_register(&pck3);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91rm9200_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 05774e5..99affb5 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -1152,14 +1152,6 @@
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91rm9200_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1168,13 +1160,9 @@
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index 46f7742..a27bbec 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -268,18 +268,6 @@
 	clk_register(&pck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9260_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 5652dde..ad00fe9 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -1229,14 +1229,6 @@
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9260_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1245,13 +1237,9 @@
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 7de81e6..c77d503 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -239,18 +239,6 @@
 	clk_register(&hck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9261_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 4db961a..9295e90 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -1051,14 +1051,6 @@
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9261_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1067,13 +1059,9 @@
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index ef301be..7fae365 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -255,18 +255,6 @@
 	clk_register(&pck3);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9263_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index fe99206..dfe5bc0 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -1461,14 +1461,6 @@
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9263_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1477,13 +1469,9 @@
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index d222f83..f205449 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -288,18 +288,6 @@
 	clk_register(&pck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9g45_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 6b008ae..db2f88c 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -1741,14 +1741,6 @@
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9g45_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1757,13 +1749,9 @@
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index d9f2774..e420085 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -232,18 +232,6 @@
 	clk_register(&pck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9rl_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index fe4ae22..9c0b148 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -1192,14 +1192,6 @@
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9rl_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1208,13 +1200,9 @@
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index 2628384..271f994 100644
--- a/arch/arm/mach-at91/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -47,20 +47,6 @@
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata onearm_eth_data = {
@@ -82,6 +68,16 @@
 static void __init onearm_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&onearm_eth_data);
diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c
index 161efba..b7d8aa7 100644
--- a/arch/arm/mach-at91/board-afeb-9260v1.c
+++ b/arch/arm/mach-at91/board-afeb-9260v1.c
@@ -52,22 +52,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-			     ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR
-			   | ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-			ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -183,6 +167,18 @@
 static void __init afeb9260_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1,
+			     ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR
+			   | ATMEL_UART_DCD | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2,
+			ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&afeb9260_usbh_data);
diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c
index c6d44ee..29d3ef0 100644
--- a/arch/arm/mach-at91/board-cam60.c
+++ b/arch/arm/mach-at91/board-cam60.c
@@ -49,12 +49,6 @@
 {
 	/* Initialize processor: 10 MHz crystal */
 	at91_initialize(10000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -175,6 +169,8 @@
 static void __init cam60_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* SPI */
 	at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices));
diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c
index 59d9cf9..44328a6 100644
--- a/arch/arm/mach-at91/board-carmeva.c
+++ b/arch/arm/mach-at91/board-carmeva.c
@@ -44,17 +44,6 @@
 {
 	/* Initialize processor: 20.000 MHz crystal */
 	at91_initialize(20000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata carmeva_eth_data = {
@@ -139,6 +128,13 @@
 static void __init carmeva_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&carmeva_eth_data);
diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c
index 5f3680e..69951ec 100644
--- a/arch/arm/mach-at91/board-cpu9krea.c
+++ b/arch/arm/mach-at91/board-cpu9krea.c
@@ -52,34 +52,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS |
-		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
-		ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* USART3 on ttyS4. (Rx, Tx) */
-	at91_register_uart(AT91SAM9260_ID_US3, 4, 0);
-
-	/* USART4 on ttyS5. (Rx, Tx) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx, Tx) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -352,6 +324,30 @@
 	/* NOR */
 	cpu9krea_add_device_nor();
 	/* Serial */
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS |
+		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
+		ATMEL_UART_DCD | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
+
+	/* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
+
+	/* USART3 on ttyS4. (Rx, Tx) */
+	at91_register_uart(AT91SAM9260_ID_US3, 4, 0);
+
+	/* USART4 on ttyS5. (Rx, Tx) */
+	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
+
+	/* USART5 on ttyS6. (Rx, Tx) */
+	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&cpu9krea_usbh_data);
diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c
index e094cc8..895cf2d 100644
--- a/arch/arm/mach-at91/board-cpuat91.c
+++ b/arch/arm/mach-at91/board-cpuat91.c
@@ -59,28 +59,6 @@
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
-		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
-		ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART2 on ttyS3 (Rx, Tx) */
-	at91_register_uart(AT91RM9200_ID_US2, 3, 0);
-
-	/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata cpuat91_eth_data = {
@@ -161,6 +139,24 @@
 static void __init cpuat91_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
+		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
+		ATMEL_UART_DCD | ATMEL_UART_RI);
+
+	/* USART2 on ttyS3 (Rx, Tx) */
+	at91_register_uart(AT91RM9200_ID_US2, 3, 0);
+
+	/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* LEDs. */
 	at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));
diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c
index 1a1547b..cd81336 100644
--- a/arch/arm/mach-at91/board-csb337.c
+++ b/arch/arm/mach-at91/board-csb337.c
@@ -47,15 +47,6 @@
 {
 	/* Initialize processor: 3.6864 MHz crystal */
 	at91_initialize(3686400);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
-
-	/* DBGU on ttyS0 */
-	at91_register_uart(0, 0, 0);
-
-	/* make console=ttyS0 the default */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata csb337_eth_data = {
@@ -228,7 +219,11 @@
 
 static void __init csb337_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 	/* Serial */
+	/* DBGU on ttyS0 */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&csb337_eth_data);
diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
index f650bf3..7c8b05a 100644
--- a/arch/arm/mach-at91/board-csb637.c
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -44,12 +44,6 @@
 {
 	/* Initialize processor: 3.6864 MHz crystal */
 	at91_initialize(3686400);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* make console=ttyS0 (ie, DBGU) the default */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata csb637_eth_data = {
@@ -118,6 +112,8 @@
 	/* LED(s) */
 	at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&csb637_eth_data);
diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c
index c18d4d30..a1fce05 100644
--- a/arch/arm/mach-at91/board-dt.c
+++ b/arch/arm/mach-at91/board-dt.c
@@ -1,10 +1,6 @@
 /*
  *  Setup code for AT91SAM Evaluation Kits with Device Tree support
  *
- *  Covers: * AT91SAM9G45-EKES  board
- *          * AT91SAM9M10-EKES  board
- *          * AT91SAM9M10G45-EK board
- *
  *  Copyright (C) 2011 Atmel,
  *                2011 Nicolas Ferre <nicolas.ferre@atmel.com>
  *
@@ -49,9 +45,7 @@
 }
 
 static const char *at91_dt_board_compat[] __initdata = {
-	"atmel,at91sam9m10g45ek",
-	"atmel,at91sam9x5ek",
-	"calao,usb-a9g20",
+	"atmel,at91sam9",
 	NULL
 };
 
diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c
index d302ca3..bd10172 100644
--- a/arch/arm/mach-at91/board-eb9200.c
+++ b/arch/arm/mach-at91/board-eb9200.c
@@ -44,20 +44,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			| ATMEL_UART_RI);
-
-	/* USART2 on ttyS2. (Rx, Tx) - IRDA */
-	at91_register_uart(AT91RM9200_ID_US2, 2, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata eb9200_eth_data = {
@@ -101,6 +87,16 @@
 static void __init eb9200_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			| ATMEL_UART_RI);
+
+	/* USART2 on ttyS2. (Rx, Tx) - IRDA */
+	at91_register_uart(AT91RM9200_ID_US2, 2, 0);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&eb9200_eth_data);
diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c
index 69966ce..89cc372 100644
--- a/arch/arm/mach-at91/board-ecbat91.c
+++ b/arch/arm/mach-at91/board-ecbat91.c
@@ -50,18 +50,6 @@
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx & Tx only) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata ecb_at91eth_data = {
@@ -151,7 +139,15 @@
 
 static void __init ecb_at91board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx & Tx only) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
 	at91_add_device_serial();
 
 	/* Ethernet */
diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c
index f23aabe..558546c 100644
--- a/arch/arm/mach-at91/board-eco920.c
+++ b/arch/arm/mach-at91/board-eco920.c
@@ -37,15 +37,6 @@
 	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
 
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
-
-	/* DBGU on ttyS0. (Rx & Tx only */
-	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata eco920_eth_data = {
@@ -103,6 +94,10 @@
 
 static void __init eco920_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
+	/* DBGU on ttyS0. (Rx & Tx only */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	at91_add_device_eth(&eco920_eth_data);
 	at91_add_device_usbh(&eco920_usbh_data);
diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c
index 1815152..47658f7 100644
--- a/arch/arm/mach-at91/board-flexibity.c
+++ b/arch/arm/mach-at91/board-flexibity.c
@@ -41,12 +41,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /* USB Host port */
@@ -143,6 +137,8 @@
 static void __init flexibity_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&flexibity_usbh_data);
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
index caf017f..33411e6 100644
--- a/arch/arm/mach-at91/board-foxg20.c
+++ b/arch/arm/mach-at91/board-foxg20.c
@@ -61,44 +61,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-				ATMEL_UART_CTS
-				| ATMEL_UART_RTS
-				| ATMEL_UART_DTR
-				| ATMEL_UART_DSR
-				| ATMEL_UART_DCD
-				| ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-		ATMEL_UART_CTS
-		| ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
-
-	/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US3, 4,
-		ATMEL_UART_CTS
-		| ATMEL_UART_RTS);
-
-	/* USART4 on ttyS5. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-
-	/* Set the internal pull-up resistor on DRXD */
-	at91_set_A_periph(AT91_PIN_PB14, 1);
-
 }
 
 /*
@@ -241,6 +203,39 @@
 static void __init foxg20_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1,
+				ATMEL_UART_CTS
+				| ATMEL_UART_RTS
+				| ATMEL_UART_DTR
+				| ATMEL_UART_DSR
+				| ATMEL_UART_DCD
+				| ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2,
+		ATMEL_UART_CTS
+		| ATMEL_UART_RTS);
+
+	/* USART2 on ttyS3. (Rx & Tx only) */
+	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
+
+	/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US3, 4,
+		ATMEL_UART_CTS
+		| ATMEL_UART_RTS);
+
+	/* USART4 on ttyS5. (Rx & Tx only) */
+	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
+
+	/* USART5 on ttyS6. (Rx & Tx only) */
+	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
+
+	/* Set the internal pull-up resistor on DRXD */
+	at91_set_A_periph(AT91_PIN_PB14, 1);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&foxg20_usbh_data);
diff --git a/arch/arm/mach-at91/board-gsia18s.c b/arch/arm/mach-at91/board-gsia18s.c
index 230e719..3e0dfa6 100644
--- a/arch/arm/mach-at91/board-gsia18s.c
+++ b/arch/arm/mach-at91/board-gsia18s.c
@@ -41,38 +41,6 @@
 static void __init gsia18s_init_early(void)
 {
 	stamp9g20_init_early();
-
-	/*
-	 * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI).
-	 * Used for Internal Analog Modem.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-				ATMEL_UART_CTS | ATMEL_UART_RTS |
-				ATMEL_UART_DTR | ATMEL_UART_DSR |
-				ATMEL_UART_DCD | ATMEL_UART_RI);
-	/*
-	 * USART1 on ttyS2 (Rx, Tx, CTS, RTS).
-	 * Used for GPS or WiFi or Data stream.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-				ATMEL_UART_CTS | ATMEL_UART_RTS);
-	/*
-	 * USART2 on ttyS3 (Rx, Tx, CTS, RTS).
-	 * Used for External Modem.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US2, 3,
-				ATMEL_UART_CTS | ATMEL_UART_RTS);
-	/*
-	 * USART3 on ttyS4 (Rx, Tx, RTS).
-	 * Used for RS-485.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS);
-
-	/*
-	 * USART4 on ttyS5 (Rx, Tx).
-	 * Used for TRX433 Radio Module.
-	 */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
 }
 
 /*
@@ -558,6 +526,37 @@
 
 static void __init gsia18s_board_init(void)
 {
+	/*
+	 * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI).
+	 * Used for Internal Analog Modem.
+	 */
+	at91_register_uart(AT91SAM9260_ID_US0, 1,
+				ATMEL_UART_CTS | ATMEL_UART_RTS |
+				ATMEL_UART_DTR | ATMEL_UART_DSR |
+				ATMEL_UART_DCD | ATMEL_UART_RI);
+	/*
+	 * USART1 on ttyS2 (Rx, Tx, CTS, RTS).
+	 * Used for GPS or WiFi or Data stream.
+	 */
+	at91_register_uart(AT91SAM9260_ID_US1, 2,
+				ATMEL_UART_CTS | ATMEL_UART_RTS);
+	/*
+	 * USART2 on ttyS3 (Rx, Tx, CTS, RTS).
+	 * Used for External Modem.
+	 */
+	at91_register_uart(AT91SAM9260_ID_US2, 3,
+				ATMEL_UART_CTS | ATMEL_UART_RTS);
+	/*
+	 * USART3 on ttyS4 (Rx, Tx, RTS).
+	 * Used for RS-485.
+	 */
+	at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS);
+
+	/*
+	 * USART4 on ttyS5 (Rx, Tx).
+	 * Used for TRX433 Radio Module.
+	 */
+	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
 	stamp9g20_board_init();
 	at91_add_device_usbh(&usbh_data);
 	at91_add_device_udc(&udc_data);
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index efde1b2..f260657 100644
--- a/arch/arm/mach-at91/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -47,18 +47,6 @@
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Set up the LEDs */
-	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata kafa_eth_data = {
@@ -79,7 +67,15 @@
 
 static void __init kafa_board_init(void)
 {
+	/* Set up the LEDs */
+	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&kafa_eth_data);
diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
index 59b92aa..ba39db5 100644
--- a/arch/arm/mach-at91/board-kb9202.c
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -50,24 +50,6 @@
 
 	/* Initialize processor: 10 MHz crystal */
 	at91_initialize(10000000);
-
-	/* Set up the LEDs */
-	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx & Tx only) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
-	/* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, 0);
-
-	/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
-	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata kb9202_eth_data = {
@@ -115,7 +97,21 @@
 
 static void __init kb9202_board_init(void)
 {
+	/* Set up the LEDs */
+	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx & Tx only) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
+
+	/* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, 0);
+
+	/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
+	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&kb9202_eth_data);
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
index 57d5f6a..d2f4cc1 100644
--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -55,15 +55,6 @@
 {
 	/* Initialize processor: 20 MHz crystal */
 	at91_initialize(20000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -341,6 +332,11 @@
 static void __init neocore926_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 
 	/* USB Host */
diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index b4a12fc..7fe6383 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -40,17 +40,6 @@
 static void __init pcontrol_g20_init_early(void)
 {
 	stamp9g20_init_early();
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
-						| ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485  X5 */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
-						| ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
-	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
 }
 
 static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
@@ -199,6 +188,16 @@
 
 static void __init pcontrol_g20_board_init(void)
 {
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
+						| ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485  X5 */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
+						| ATMEL_UART_RTS);
+
+	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
+	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
 	stamp9g20_board_init();
 	at91_add_device_usbh(&usbh_data);
 	at91_add_device_eth(&macb_data);
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index 59e35dd..b45c0a5 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -48,17 +48,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			  | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata picotux200_eth_data = {
@@ -106,6 +95,13 @@
 static void __init picotux200_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			  | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&picotux200_eth_data);
diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
index b6ed5ed..0c61bf0d 100644
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ b/arch/arm/mach-at91/board-qil-a9260.c
@@ -52,24 +52,6 @@
 {
 	/* Initialize processor: 12.000 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS1 (ie, USART0) */
-	at91_set_serial_console(1);
-
 }
 
 /*
@@ -235,6 +217,19 @@
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c
index 01332aa..afd7a47 100644
--- a/arch/arm/mach-at91/board-rm9200dk.c
+++ b/arch/arm/mach-at91/board-rm9200dk.c
@@ -50,20 +50,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata dk_eth_data = {
@@ -190,7 +176,17 @@
 
 static void __init dk_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&dk_eth_data);
diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c
index b2e4fe2..2b15b8a 100644
--- a/arch/arm/mach-at91/board-rm9200ek.c
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -50,20 +50,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata ek_eth_data = {
@@ -161,7 +147,17 @@
 
 static void __init ek_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&ek_eth_data);
diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c
index af0750f..24ab9be 100644
--- a/arch/arm/mach-at91/board-rsi-ews.c
+++ b/arch/arm/mach-at91/board-rsi-ews.c
@@ -35,26 +35,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	/* This one is for debugging */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	/* Dialin/-out modem interface */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART3 on ttyS4. (Rx, Tx, RTS) */
-	/* RS485 communication */
-	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -204,7 +184,23 @@
  */
 static void __init rsi_ews_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	/* This one is for debugging */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	/* Dialin/-out modem interface */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART3 on ttyS4. (Rx, Tx, RTS) */
+	/* RS485 communication */
+	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
 	at91_add_device_serial();
 	at91_set_gpio_output(AT91_PIN_PA21, 0);
 	/* Ethernet */
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index e8b116b..cdd21f2 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -48,23 +48,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -184,7 +167,20 @@
 
 static void __init ek_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index d5aec55..7b3c391 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -54,20 +54,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -320,6 +306,16 @@
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 065fed3..2736453 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -58,15 +58,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -577,7 +568,12 @@
 
 static void __init ek_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 2ffe50f3..983cb98 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -57,15 +57,6 @@
 {
 	/* Initialize processor: 16.367 MHz crystal */
 	at91_initialize(16367660);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -412,6 +403,11 @@
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index 8923ec9..3d61553 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -65,20 +65,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -372,6 +358,16 @@
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index c88e908..9a87f0b0 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -53,16 +53,6 @@
 {
 	/* Initialize processor: 12.000 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 not connected on the -EK board */
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -457,6 +447,12 @@
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 not connected on the -EK board */
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB HS Host */
 	at91_add_device_usbh_ohci(&ek_usbh_hs_data);
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index b109ce2..be3239f 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -42,15 +42,6 @@
 {
 	/* Initialize processor: 12.000 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -296,6 +287,11 @@
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB HS */
 	at91_add_device_usba(&ek_usba_udc_data);
diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c
index ebc9d01..9d446f1b 100644
--- a/arch/arm/mach-at91/board-snapper9260.c
+++ b/arch/arm/mach-at91/board-snapper9260.c
@@ -43,16 +43,6 @@
 static void __init snapper9260_init_early(void)
 {
 	at91_initialize(18432000);
-
-	/* Debug on ttyS0 */
-	at91_register_uart(0, 0, 0);
-	at91_set_serial_console(0);
-
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-			   ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-			   ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
 }
 
 static struct at91_usbh_data __initdata snapper9260_usbh_data = {
@@ -168,6 +158,14 @@
 	snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31);
 	i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1);
 
+	/* Debug on ttyS0 */
+	at91_register_uart(0, 0, 0);
+
+	at91_register_uart(AT91SAM9260_ID_US0, 1,
+			   ATMEL_UART_CTS | ATMEL_UART_RTS);
+	at91_register_uart(AT91SAM9260_ID_US1, 2,
+			   ATMEL_UART_CTS | ATMEL_UART_RTS);
+	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
 	at91_add_device_serial();
 	at91_add_device_usbh(&snapper9260_usbh_data);
 	at91_add_device_udc(&snapper9260_udc_data);
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
index 7640049..ee86f9d 100644
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ b/arch/arm/mach-at91/board-stamp9g20.c
@@ -36,44 +36,6 @@
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-}
-
-static void __init stamp9g20evb_init_early(void)
-{
-	stamp9g20_init_early();
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-						| ATMEL_UART_DTR | ATMEL_UART_DSR
-						| ATMEL_UART_DCD | ATMEL_UART_RI);
-}
-
-static void __init portuxg20_init_early(void)
-{
-	stamp9g20_init_early();
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-						| ATMEL_UART_DTR | ATMEL_UART_DSR
-						| ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART4 on ttyS5. (Rx, Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx, Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
 }
 
 /*
@@ -254,6 +216,8 @@
 void __init stamp9g20_board_init(void)
 {
 	/* Serial */
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* NAND */
 	add_device_nand();
@@ -269,6 +233,22 @@
 
 static void __init portuxg20_board_init(void)
 {
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+						| ATMEL_UART_DTR | ATMEL_UART_DSR
+						| ATMEL_UART_DCD | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* USART4 on ttyS5. (Rx, Tx only) */
+	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
+
+	/* USART5 on ttyS6. (Rx, Tx only) */
+	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
 	stamp9g20_board_init();
 	/* USB Host */
 	at91_add_device_usbh(&usbh_data);
@@ -286,6 +266,10 @@
 
 static void __init stamp9g20evb_board_init(void)
 {
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+						| ATMEL_UART_DTR | ATMEL_UART_DSR
+						| ATMEL_UART_DCD | ATMEL_UART_RI);
 	stamp9g20_board_init();
 	/* USB Host */
 	at91_add_device_usbh(&usbh_data);
@@ -303,7 +287,7 @@
 	/* Maintainer: taskit GmbH */
 	.timer		= &at91sam926x_timer,
 	.map_io		= at91_map_io,
-	.init_early	= portuxg20_init_early,
+	.init_early	= stamp9g20_init_early,
 	.init_irq	= at91_init_irq_default,
 	.init_machine	= portuxg20_board_init,
 MACHINE_END
@@ -312,7 +296,7 @@
 	/* Maintainer: taskit GmbH */
 	.timer		= &at91sam926x_timer,
 	.map_io		= at91_map_io,
-	.init_early	= stamp9g20evb_init_early,
+	.init_early	= stamp9g20_init_early,
 	.init_irq	= at91_init_irq_default,
 	.init_machine	= stamp9g20evb_board_init,
 MACHINE_END
diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c
index b7483a3..332ecd4 100644
--- a/arch/arm/mach-at91/board-usb-a926x.c
+++ b/arch/arm/mach-at91/board-usb-a926x.c
@@ -53,12 +53,6 @@
 {
 	/* Initialize processor: 12.00 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -325,6 +319,8 @@
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);
diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c
index 38dd279..d56665e 100644
--- a/arch/arm/mach-at91/board-yl-9200.c
+++ b/arch/arm/mach-at91/board-yl-9200.c
@@ -58,26 +58,6 @@
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
-	at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			| ATMEL_UART_RI);
-
-	/* USART0 on ttyS2. (Rx & Tx only to JP3) */
-	at91_register_uart(AT91RM9200_ID_US0, 2, 0);
-
-	/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
-	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*
@@ -560,7 +540,23 @@
 
 static void __init yl9200_board_init(void)
 {
+	/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
+	at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
+
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			| ATMEL_UART_RI);
+
+	/* USART0 on ttyS2. (Rx & Tx only to JP3) */
+	at91_register_uart(AT91RM9200_ID_US0, 2, 0);
+
+	/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
+	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&yl9200_eth_data);
diff --git a/arch/arm/mach-at91/cpuidle.c b/arch/arm/mach-at91/cpuidle.c
index ece1f9a..0c63815 100644
--- a/arch/arm/mach-at91/cpuidle.c
+++ b/arch/arm/mach-at91/cpuidle.c
@@ -21,6 +21,7 @@
 #include <linux/export.h>
 #include <asm/proc-fns.h>
 #include <asm/cpuidle.h>
+#include <mach/cpu.h>
 
 #include "pm.h"
 
@@ -33,7 +34,12 @@
 			struct cpuidle_driver *drv,
 			       int index)
 {
-	at91_standby();
+	if (cpu_is_at91rm9200())
+		at91rm9200_standby();
+	else if (cpu_is_at91sam9g45())
+		at91sam9g45_standby();
+	else
+		at91sam9_standby();
 
 	return index;
 }
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
index dd9b346..0a60bf8 100644
--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -40,17 +40,6 @@
 extern struct sys_timer at91x40_timer;
 
  /* Clocks */
-/*
- * function to specify the clock of the default console. As we do not
- * use the device/driver bus, the dev_name is not intialize. So we need
- * to link the clock to a specific con_id only "usart"
- */
-extern void __init at91rm9200_set_console_clock(int id);
-extern void __init at91sam9260_set_console_clock(int id);
-extern void __init at91sam9261_set_console_clock(int id);
-extern void __init at91sam9263_set_console_clock(int id);
-extern void __init at91sam9rl_set_console_clock(int id);
-extern void __init at91sam9g45_set_console_clock(int id);
 #ifdef CONFIG_AT91_PMC_UNIT
 extern int __init at91_clock_init(unsigned long main_clock);
 extern int __init at91_dt_clock_init(void);
diff --git a/arch/arm/mach-at91/include/mach/at91rm9200.h b/arch/arm/mach-at91/include/mach/at91rm9200.h
index 603e6aa..e67317c 100644
--- a/arch/arm/mach-at91/include/mach/at91rm9200.h
+++ b/arch/arm/mach-at91/include/mach/at91rm9200.h
@@ -88,11 +88,6 @@
 #define AT91RM9200_BASE_RTC	0xfffffe00	/* Real-Time Clock */
 #define AT91RM9200_BASE_MC	0xffffff00	/* Memory Controllers */
 
-#define AT91_USART0	AT91RM9200_BASE_US0
-#define AT91_USART1	AT91RM9200_BASE_US1
-#define AT91_USART2	AT91RM9200_BASE_US2
-#define AT91_USART3	AT91RM9200_BASE_US3
-
 /*
  * Internal Memory.
  */
diff --git a/arch/arm/mach-at91/include/mach/at91sam9260.h b/arch/arm/mach-at91/include/mach/at91sam9260.h
index 08ae9af..416c7b6 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9260.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9260.h
@@ -95,13 +95,6 @@
 #define AT91SAM9260_BASE_WDT	0xfffffd40
 #define AT91SAM9260_BASE_GPBR	0xfffffd50
 
-#define AT91_USART0	AT91SAM9260_BASE_US0
-#define AT91_USART1	AT91SAM9260_BASE_US1
-#define AT91_USART2	AT91SAM9260_BASE_US2
-#define AT91_USART3	AT91SAM9260_BASE_US3
-#define AT91_USART4	AT91SAM9260_BASE_US4
-#define AT91_USART5	AT91SAM9260_BASE_US5
-
 
 /*
  * Internal Memory.
diff --git a/arch/arm/mach-at91/include/mach/at91sam9261.h b/arch/arm/mach-at91/include/mach/at91sam9261.h
index 44fbdc1..a041406 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9261.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9261.h
@@ -79,10 +79,6 @@
 #define AT91SAM9261_BASE_WDT	0xfffffd40
 #define AT91SAM9261_BASE_GPBR	0xfffffd50
 
-#define AT91_USART0	AT91SAM9261_BASE_US0
-#define AT91_USART1	AT91SAM9261_BASE_US1
-#define AT91_USART2	AT91SAM9261_BASE_US2
-
 
 /*
  * Internal Memory.
diff --git a/arch/arm/mach-at91/include/mach/at91sam9263.h b/arch/arm/mach-at91/include/mach/at91sam9263.h
index d96cbb2..d201029 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9263.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9263.h
@@ -95,10 +95,6 @@
 #define AT91SAM9263_BASE_RTT1	0xfffffd50
 #define AT91SAM9263_BASE_GPBR	0xfffffd60
 
-#define AT91_USART0	AT91SAM9263_BASE_US0
-#define AT91_USART1	AT91SAM9263_BASE_US1
-#define AT91_USART2	AT91SAM9263_BASE_US2
-
 #define AT91_SMC	AT91_SMC0
 
 /*
diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45.h b/arch/arm/mach-at91/include/mach/at91sam9g45.h
index d052abc..3a4da24 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9g45.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9g45.h
@@ -106,11 +106,6 @@
 #define AT91SAM9G45_BASE_RTC	0xfffffdb0
 #define AT91SAM9G45_BASE_GPBR	0xfffffd60
 
-#define AT91_USART0	AT91SAM9G45_BASE_US0
-#define AT91_USART1	AT91SAM9G45_BASE_US1
-#define AT91_USART2	AT91SAM9G45_BASE_US2
-#define AT91_USART3	AT91SAM9G45_BASE_US3
-
 /*
  * Internal Memory.
  */
diff --git a/arch/arm/mach-at91/include/mach/at91sam9rl.h b/arch/arm/mach-at91/include/mach/at91sam9rl.h
index e0073eb..a15db56 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9rl.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9rl.h
@@ -89,11 +89,6 @@
 #define AT91SAM9RL_BASE_GPBR	0xfffffd60
 #define AT91SAM9RL_BASE_RTC	0xfffffe00
 
-#define AT91_USART0	AT91SAM9RL_BASE_US0
-#define AT91_USART1	AT91SAM9RL_BASE_US1
-#define AT91_USART2	AT91SAM9RL_BASE_US2
-#define AT91_USART3	AT91SAM9RL_BASE_US3
-
 
 /*
  * Internal Memory.
diff --git a/arch/arm/mach-at91/include/mach/at91sam9x5.h b/arch/arm/mach-at91/include/mach/at91sam9x5.h
index 88e43d5..c75ee19 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9x5.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9x5.h
@@ -55,14 +55,6 @@
 #define AT91SAM9X5_BASE_USART2	0xf8024000
 
 /*
- * Base addresses for early serial code (uncompress.h)
- */
-#define AT91_DBGU	AT91_BASE_DBGU0
-#define AT91_USART0	AT91SAM9X5_BASE_USART0
-#define AT91_USART1	AT91SAM9X5_BASE_USART1
-#define AT91_USART2	AT91SAM9X5_BASE_USART2
-
-/*
  * Internal Memory.
  */
 #define AT91SAM9X5_SRAM_BASE	0x00300000	/* Internal SRAM base address */
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 49a8211..369afc2 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -121,7 +121,6 @@
 #define ATMEL_UART_RI	0x20
 
 extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
-extern void __init at91_set_serial_console(unsigned portnr);
 
 extern struct platform_device *atmel_default_console_device;
 
diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h
index 0118c33..73d2fd2 100644
--- a/arch/arm/mach-at91/include/mach/cpu.h
+++ b/arch/arm/mach-at91/include/mach/cpu.h
@@ -54,6 +54,7 @@
 #define ARCH_REVISON_9200_BGA	(0 << 0)
 #define ARCH_REVISON_9200_PQFP	(1 << 0)
 
+#ifndef __ASSEMBLY__
 enum at91_soc_type {
 	/* 920T */
 	AT91_SOC_RM9200,
@@ -106,7 +107,7 @@
 	return at91_soc_initdata.type != AT91_SOC_NONE;
 }
 
-#ifdef CONFIG_ARCH_AT91RM9200
+#ifdef CONFIG_SOC_AT91RM9200
 #define cpu_is_at91rm9200()	(at91_soc_initdata.type == AT91_SOC_RM9200)
 #define cpu_is_at91rm9200_bga()	(at91_soc_initdata.subtype == AT91_SOC_RM9200_BGA)
 #define cpu_is_at91rm9200_pqfp() (at91_soc_initdata.subtype == AT91_SOC_RM9200_PQFP)
@@ -116,45 +117,37 @@
 #define cpu_is_at91rm9200_pqfp() (0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9260
+#ifdef CONFIG_SOC_AT91SAM9260
 #define cpu_is_at91sam9xe()	(at91_soc_initdata.subtype == AT91_SOC_SAM9XE)
 #define cpu_is_at91sam9260()	(at91_soc_initdata.type == AT91_SOC_SAM9260)
+#define cpu_is_at91sam9g20()	(at91_soc_initdata.type == AT91_SOC_SAM9G20)
 #else
 #define cpu_is_at91sam9xe()	(0)
 #define cpu_is_at91sam9260()	(0)
-#endif
-
-#ifdef CONFIG_ARCH_AT91SAM9G20
-#define cpu_is_at91sam9g20()	(at91_soc_initdata.type == AT91_SOC_SAM9G20)
-#else
 #define cpu_is_at91sam9g20()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9261
+#ifdef CONFIG_SOC_AT91SAM9261
 #define cpu_is_at91sam9261()	(at91_soc_initdata.type == AT91_SOC_SAM9261)
-#else
-#define cpu_is_at91sam9261()	(0)
-#endif
-
-#ifdef CONFIG_ARCH_AT91SAM9G10
 #define cpu_is_at91sam9g10()	(at91_soc_initdata.type == AT91_SOC_SAM9G10)
 #else
+#define cpu_is_at91sam9261()	(0)
 #define cpu_is_at91sam9g10()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9263
+#ifdef CONFIG_SOC_AT91SAM9263
 #define cpu_is_at91sam9263()	(at91_soc_initdata.type == AT91_SOC_SAM9263)
 #else
 #define cpu_is_at91sam9263()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9RL
+#ifdef CONFIG_SOC_AT91SAM9RL
 #define cpu_is_at91sam9rl()	(at91_soc_initdata.type == AT91_SOC_SAM9RL)
 #else
 #define cpu_is_at91sam9rl()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9G45
+#ifdef CONFIG_SOC_AT91SAM9G45
 #define cpu_is_at91sam9g45()	(at91_soc_initdata.type == AT91_SOC_SAM9G45)
 #define cpu_is_at91sam9g45es()	(at91_soc_initdata.subtype == AT91_SOC_SAM9G45ES)
 #define cpu_is_at91sam9m10()	(at91_soc_initdata.subtype == AT91_SOC_SAM9M10)
@@ -168,7 +161,7 @@
 #define cpu_is_at91sam9m11()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9X5
+#ifdef CONFIG_SOC_AT91SAM9X5
 #define cpu_is_at91sam9x5()	(at91_soc_initdata.type == AT91_SOC_SAM9X5)
 #define cpu_is_at91sam9g15()	(at91_soc_initdata.subtype == AT91_SOC_SAM9G15)
 #define cpu_is_at91sam9g35()	(at91_soc_initdata.subtype == AT91_SOC_SAM9G35)
@@ -189,5 +182,6 @@
  * definitions may reduce clutter in common drivers.
  */
 #define cpu_is_at32ap7000()	(0)
+#endif /* __ASSEMBLY__ */
 
 #endif /* __MACH_CPU_H__ */
diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h
index e9e29a6..3a01f8f 100644
--- a/arch/arm/mach-at91/include/mach/hardware.h
+++ b/arch/arm/mach-at91/include/mach/hardware.h
@@ -22,27 +22,17 @@
 /* 9263, 9g45 */
 #define AT91_BASE_DBGU1	0xffffee00
 
-#if defined(CONFIG_ARCH_AT91RM9200)
-#include <mach/at91rm9200.h>
-#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)
-#include <mach/at91sam9260.h>
-#elif defined(CONFIG_ARCH_AT91SAM9261) || defined(CONFIG_ARCH_AT91SAM9G10)
-#include <mach/at91sam9261.h>
-#elif defined(CONFIG_ARCH_AT91SAM9263)
-#include <mach/at91sam9263.h>
-#elif defined(CONFIG_ARCH_AT91SAM9RL)
-#include <mach/at91sam9rl.h>
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-#include <mach/at91sam9g45.h>
-#elif defined(CONFIG_ARCH_AT91SAM9X5)
-#include <mach/at91sam9x5.h>
-#elif defined(CONFIG_ARCH_AT91X40)
+#if defined(CONFIG_ARCH_AT91X40)
 #include <mach/at91x40.h>
 #else
-#error "Unsupported AT91 processor"
-#endif
+#include <mach/at91rm9200.h>
+#include <mach/at91sam9260.h>
+#include <mach/at91sam9261.h>
+#include <mach/at91sam9263.h>
+#include <mach/at91sam9rl.h>
+#include <mach/at91sam9g45.h>
+#include <mach/at91sam9x5.h>
 
-#if !defined(CONFIG_ARCH_AT91X40)
 /*
  * On all at91 except rm9200 and x40 have the System Controller starts
  * at address 0xffffc000 and has a size of 16KiB.
diff --git a/arch/arm/mach-at91/include/mach/uncompress.h b/arch/arm/mach-at91/include/mach/uncompress.h
index 4218647..6f6118d 100644
--- a/arch/arm/mach-at91/include/mach/uncompress.h
+++ b/arch/arm/mach-at91/include/mach/uncompress.h
@@ -1,7 +1,8 @@
 /*
  * arch/arm/mach-at91/include/mach/uncompress.h
  *
- *  Copyright (C) 2003 SAN People
+ * Copyright (C) 2003 SAN People
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -25,22 +26,147 @@
 #include <linux/atmel_serial.h>
 #include <mach/hardware.h>
 
-#if defined(CONFIG_AT91_EARLY_DBGU0)
-#define UART_OFFSET AT91_BASE_DBGU0
-#elif defined(CONFIG_AT91_EARLY_DBGU1)
-#define UART_OFFSET AT91_BASE_DBGU1
-#elif defined(CONFIG_AT91_EARLY_USART0)
-#define UART_OFFSET AT91_USART0
-#elif defined(CONFIG_AT91_EARLY_USART1)
-#define UART_OFFSET AT91_USART1
-#elif defined(CONFIG_AT91_EARLY_USART2)
-#define UART_OFFSET AT91_USART2
-#elif defined(CONFIG_AT91_EARLY_USART3)
-#define UART_OFFSET AT91_USART3
-#elif defined(CONFIG_AT91_EARLY_USART4)
-#define UART_OFFSET AT91_USART4
-#elif defined(CONFIG_AT91_EARLY_USART5)
-#define UART_OFFSET AT91_USART5
+#include <mach/at91_dbgu.h>
+#include <mach/cpu.h>
+
+void __iomem *at91_uart;
+
+#if !defined(CONFIG_ARCH_AT91X40)
+static const u32 uarts_rm9200[] = {
+	AT91_BASE_DBGU0,
+	AT91RM9200_BASE_US0,
+	AT91RM9200_BASE_US1,
+	AT91RM9200_BASE_US2,
+	AT91RM9200_BASE_US3,
+	0,
+};
+
+static const u32 uarts_sam9260[] = {
+	AT91_BASE_DBGU0,
+	AT91SAM9260_BASE_US0,
+	AT91SAM9260_BASE_US1,
+	AT91SAM9260_BASE_US2,
+	AT91SAM9260_BASE_US3,
+	AT91SAM9260_BASE_US4,
+	AT91SAM9260_BASE_US5,
+	0,
+};
+
+static const u32 uarts_sam9261[] = {
+	AT91_BASE_DBGU0,
+	AT91SAM9261_BASE_US0,
+	AT91SAM9261_BASE_US1,
+	AT91SAM9261_BASE_US2,
+	0,
+};
+
+static const u32 uarts_sam9263[] = {
+	AT91_BASE_DBGU1,
+	AT91SAM9263_BASE_US0,
+	AT91SAM9263_BASE_US1,
+	AT91SAM9263_BASE_US2,
+	0,
+};
+
+static const u32 uarts_sam9g45[] = {
+	AT91_BASE_DBGU1,
+	AT91SAM9G45_BASE_US0,
+	AT91SAM9G45_BASE_US1,
+	AT91SAM9G45_BASE_US2,
+	AT91SAM9G45_BASE_US3,
+	0,
+};
+
+static const u32 uarts_sam9rl[] = {
+	AT91_BASE_DBGU0,
+	AT91SAM9RL_BASE_US0,
+	AT91SAM9RL_BASE_US1,
+	AT91SAM9RL_BASE_US2,
+	AT91SAM9RL_BASE_US3,
+	0,
+};
+
+static const u32 uarts_sam9x5[] = {
+	AT91_BASE_DBGU0,
+	AT91SAM9X5_BASE_USART0,
+	AT91SAM9X5_BASE_USART1,
+	AT91SAM9X5_BASE_USART2,
+	0,
+};
+
+static inline const u32* decomp_soc_detect(u32 dbgu_base)
+{
+	u32 cidr, socid;
+
+	cidr = __raw_readl(dbgu_base + AT91_DBGU_CIDR);
+	socid = cidr & ~AT91_CIDR_VERSION;
+
+	switch (socid) {
+	case ARCH_ID_AT91RM9200:
+		return uarts_rm9200;
+
+	case ARCH_ID_AT91SAM9G20:
+	case ARCH_ID_AT91SAM9260:
+		return uarts_sam9260;
+
+	case ARCH_ID_AT91SAM9261:
+		return uarts_sam9261;
+
+	case ARCH_ID_AT91SAM9263:
+		return uarts_sam9263;
+
+	case ARCH_ID_AT91SAM9G45:
+		return uarts_sam9g45;
+
+	case ARCH_ID_AT91SAM9RL64:
+		return uarts_sam9rl;
+
+	case ARCH_ID_AT91SAM9X5:
+		return uarts_sam9x5;
+	}
+
+	/* at91sam9g10 */
+	if ((cidr & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
+		return uarts_sam9261;
+	}
+	/* at91sam9xe */
+	else if ((cidr & AT91_CIDR_ARCH) == ARCH_FAMILY_AT91SAM9XE) {
+		return uarts_sam9260;
+	}
+
+	return NULL;
+}
+
+static inline void arch_decomp_setup(void)
+{
+	int i = 0;
+	const u32* usarts;
+
+	usarts = decomp_soc_detect(AT91_BASE_DBGU0);
+
+	if (!usarts)
+		usarts = decomp_soc_detect(AT91_BASE_DBGU1);
+	if (!usarts) {
+		at91_uart = NULL;
+		return;
+	}
+
+	do {
+		/* physical address */
+		at91_uart = (void __iomem *)usarts[i];
+
+		if (__raw_readl(at91_uart + ATMEL_US_BRGR))
+			return;
+		i++;
+	} while (usarts[i]);
+
+	at91_uart = NULL;
+}
+#else
+static inline void arch_decomp_setup(void)
+{
+	at91_uart = NULL;
+}
 #endif
 
 /*
@@ -52,28 +178,24 @@
  */
 static void putc(int c)
 {
-#ifdef UART_OFFSET
-	void __iomem *sys = (void __iomem *) UART_OFFSET;	/* physical address */
+	if (!at91_uart)
+		return;
 
-	while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXRDY))
+	while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXRDY))
 		barrier();
-	__raw_writel(c, sys + ATMEL_US_THR);
-#endif
+	__raw_writel(c, at91_uart + ATMEL_US_THR);
 }
 
 static inline void flush(void)
 {
-#ifdef UART_OFFSET
-	void __iomem *sys = (void __iomem *) UART_OFFSET;	/* physical address */
+	if (!at91_uart)
+		return;
 
 	/* wait for transmission to complete */
-	while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXEMPTY))
+	while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXEMPTY))
 		barrier();
-#endif
 }
 
-#define arch_decomp_setup()
-
 #define arch_decomp_wdog()
 
 #endif
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index f630250..1bfaad6 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -261,7 +261,12 @@
 			 * For ARM 926 based chips, this requirement is weaker
 			 * as at91sam9 can access a RAM in self-refresh mode.
 			 */
-			at91_standby();
+			if (cpu_is_at91rm9200())
+				at91rm9200_standby();
+			else if (cpu_is_at91sam9g45())
+				at91sam9g45_standby();
+			else
+				at91sam9_standby();
 			break;
 
 		case PM_SUSPEND_ON:
@@ -307,10 +312,9 @@
 
 	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
-#ifdef CONFIG_ARCH_AT91RM9200
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
-	at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
-#endif
+	if (cpu_is_at91rm9200())
+		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
 
 	suspend_set_ops(&at91_pm_ops);
 
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index 89f56f3..38f467c 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -12,7 +12,6 @@
 #define __ARCH_ARM_MACH_AT91_PM
 
 #include <mach/at91_ramc.h>
-#ifdef CONFIG_ARCH_AT91RM9200
 #include <mach/at91rm9200_sdramc.h>
 
 /*
@@ -43,10 +42,6 @@
 		  "r" (lpr));
 }
 
-#define at91_standby at91rm9200_standby
-
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-
 /* We manage both DDRAM/SDRAM controllers, we need more than one value to
  * remember.
  */
@@ -75,11 +70,7 @@
 	at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1);
 }
 
-#define at91_standby at91sam9g45_standby
-
-#else
-
-#ifdef CONFIG_ARCH_AT91SAM9263
+#ifdef CONFIG_SOC_AT91SAM9263
 /*
  * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use;
  * handle those cases both here and in the Suspend-To-RAM support.
@@ -102,8 +93,4 @@
 	at91_ramc_write(0, AT91_SDRAMC_LPR, saved_lpr);
 }
 
-#define at91_standby at91sam9_standby
-
-#endif
-
 #endif
diff --git a/arch/arm/mach-at91/pm_slowclock.S b/arch/arm/mach-at91/pm_slowclock.S
index db54521..098c28d 100644
--- a/arch/arm/mach-at91/pm_slowclock.S
+++ b/arch/arm/mach-at91/pm_slowclock.S
@@ -18,7 +18,7 @@
 #include <mach/at91_ramc.h>
 
 
-#ifdef CONFIG_ARCH_AT91SAM9263
+#ifdef CONFIG_SOC_AT91SAM9263
 /*
  * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use;
  * handle those cases both here and in the Suspend-To-RAM support.
diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h
index 5db4aa4..683dddf 100644
--- a/arch/arm/mach-at91/soc.h
+++ b/arch/arm/mach-at91/soc.h
@@ -26,30 +26,30 @@
 	return at91_boot_soc.init != NULL;
 }
 
-#if !defined(CONFIG_ARCH_AT91RM9200)
+#if !defined(CONFIG_SOC_AT91RM9200)
 #define at91rm9200_soc	at91_boot_soc
 #endif
 
-#if !(defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20))
+#if !defined(CONFIG_SOC_AT91SAM9260)
 #define at91sam9260_soc	at91_boot_soc
 #endif
 
-#if !(defined(CONFIG_ARCH_AT91SAM9261) || defined(CONFIG_ARCH_AT91SAM9G10))
+#if !defined(CONFIG_SOC_AT91SAM9261)
 #define at91sam9261_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9263)
+#if !defined(CONFIG_SOC_AT91SAM9263)
 #define at91sam9263_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9G45)
+#if !defined(CONFIG_SOC_AT91SAM9G45)
 #define at91sam9g45_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9RL)
+#if !defined(CONFIG_SOC_AT91SAM9RL)
 #define at91sam9rl_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9X5)
+#if !defined(CONFIG_SOC_AT91SAM9X5)
 #define at91sam9x5_soc	at91_boot_soc
 #endif
diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c
index e432d4a..d14bbe9 100644
--- a/arch/arm/mach-imx/mach-mx21ads.c
+++ b/arch/arm/mach-imx/mach-mx21ads.c
@@ -304,8 +304,7 @@
 	imx21_add_mxc_nand(&mx21ads_nand_board_info);
 
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-	platform_device_register_full(
-			(struct platform_device_info *)&mx21ads_cs8900_devinfo);
+	platform_device_register_full(&mx21ads_cs8900_devinfo);
 }
 
 static void __init mx21ads_timer_init(void)
diff --git a/arch/arm/mach-imx/mach-mx51_efikamx.c b/arch/arm/mach-imx/mach-mx51_efikamx.c
index 586e9f8..86e96ef 100644
--- a/arch/arm/mach-imx/mach-mx51_efikamx.c
+++ b/arch/arm/mach-imx/mach-mx51_efikamx.c
@@ -284,8 +284,7 @@
 	.init = mx51_efikamx_timer_init,
 };
 
-MACHINE_START(MX51_EFIKAMX, "Genesi EfikaMX nettop")
-	/* Maintainer: Amit Kucheria <amit.kucheria@linaro.org> */
+MACHINE_START(MX51_EFIKAMX, "Genesi Efika MX (Smarttop)")
 	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
diff --git a/arch/arm/mach-imx/mach-mx51_efikasb.c b/arch/arm/mach-imx/mach-mx51_efikasb.c
index 24aded9..88f837a 100644
--- a/arch/arm/mach-imx/mach-mx51_efikasb.c
+++ b/arch/arm/mach-imx/mach-mx51_efikasb.c
@@ -280,7 +280,7 @@
 	.init	= mx51_efikasb_timer_init,
 };
 
-MACHINE_START(MX51_EFIKASB, "Genesi Efika Smartbook")
+MACHINE_START(MX51_EFIKASB, "Genesi Efika MX (Smartbook)")
 	.atag_offset = 0x100,
 	.map_io = mx51_map_io,
 	.init_early = imx51_init_early,
diff --git a/arch/arm/mach-ixp2000/Kconfig b/arch/arm/mach-ixp2000/Kconfig
deleted file mode 100644
index 08d2707..0000000
--- a/arch/arm/mach-ixp2000/Kconfig
+++ /dev/null
@@ -1,72 +0,0 @@
-
-if ARCH_IXP2000
-
-config ARCH_SUPPORTS_BIG_ENDIAN
-	bool
-	default y
-
-menu "Intel IXP2400/2800 Implementation Options"
-
-comment "IXP2400/2800 Platforms"
-
-config ARCH_ENP2611
-	bool "Support Radisys ENP-2611"
-	help
-	  Say 'Y' here if you want your kernel to support the Radisys
-	  ENP2611 PCI network processing card. For more information on
-	  this card, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2400
-	bool "Support Intel IXDP2400"
-	help
-	  Say 'Y' here if you want your kernel to support the Intel
-	  IXDP2400 reference platform. For more information on
-	  this platform, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2800
-	bool "Support Intel IXDP2800"
-	help
-	  Say 'Y' here if you want your kernel to support the Intel
-	  IXDP2800 reference platform. For more information on
-	  this platform, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2X00
-	bool
-	depends on ARCH_IXDP2400 || ARCH_IXDP2800
-	default y	
-
-config ARCH_IXDP2401
-	bool "Support Intel IXDP2401"
-	help
-	  Say 'Y' here if you want your kernel to support the Intel
-	  IXDP2401 reference platform. For more information on
-	  this platform, see <file:Documentation/arm/IXP2000>.
-
-config ARCH_IXDP2801
-	bool "Support Intel IXDP2801 and IXDP28x5"
-	help
-	  Say 'Y' here if you want your kernel to support the Intel
-	  IXDP2801/2805/2855 reference platforms. For more information on
-	  this platform, see <file:Documentation/arm/IXP2000>.
-
-config MACH_IXDP28X5
-	bool
-	depends on ARCH_IXDP2801
-	default y
-
-config ARCH_IXDP2X01
-	bool
-	depends on ARCH_IXDP2401 || ARCH_IXDP2801
-	default y	
-
-config IXP2000_SUPPORT_BROKEN_PCI_IO
-	bool "Support broken PCI I/O on older IXP2000s"
-	default y
-	help
-	  Say 'N' here if you only intend to run your kernel on an
-	  IXP2000 B0 or later model and do not need the PCI I/O
-	  byteswap workaround.  Say 'Y' otherwise.
-
-endmenu
-
-endif
diff --git a/arch/arm/mach-ixp2000/Makefile b/arch/arm/mach-ixp2000/Makefile
deleted file mode 100644
index 1e6139d..0000000
--- a/arch/arm/mach-ixp2000/Makefile
+++ /dev/null
@@ -1,14 +0,0 @@
-#
-# Makefile for the linux kernel.
-#
-obj-y			:= core.o pci.o
-obj-m			:=
-obj-n			:=
-obj-			:=
-
-obj-$(CONFIG_ARCH_ENP2611)	+= enp2611.o
-obj-$(CONFIG_ARCH_IXDP2400)	+= ixdp2400.o
-obj-$(CONFIG_ARCH_IXDP2800)	+= ixdp2800.o
-obj-$(CONFIG_ARCH_IXDP2X00)	+= ixdp2x00.o
-obj-$(CONFIG_ARCH_IXDP2X01)	+= ixdp2x01.o
-
diff --git a/arch/arm/mach-ixp2000/Makefile.boot b/arch/arm/mach-ixp2000/Makefile.boot
deleted file mode 100644
index 9c7af91..0000000
--- a/arch/arm/mach-ixp2000/Makefile.boot
+++ /dev/null
@@ -1,3 +0,0 @@
-   zreladdr-y	+= 0x00008000
-params_phys-y	:= 0x00000100
-
diff --git a/arch/arm/mach-ixp2000/core.c b/arch/arm/mach-ixp2000/core.c
deleted file mode 100644
index f214cdf..0000000
--- a/arch/arm/mach-ixp2000/core.c
+++ /dev/null
@@ -1,520 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/core.c
- *
- * Common routines used by all IXP2400/2800 based platforms.
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2004 (C) MontaVista Software, Inc. 
- *
- * Based on work Copyright (C) 2002-2003 Intel Corporation
- * 
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any 
- * warranty of any kind, whether express or implied.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/serial_8250.h>
-#include <linux/mm.h>
-#include <linux/export.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <asm/mach/irq.h>
-
-#include <mach/gpio-ixp2000.h>
-
-static DEFINE_SPINLOCK(ixp2000_slowport_lock);
-static unsigned long ixp2000_slowport_irq_flags;
-
-/*************************************************************************
- * Slowport access routines
- *************************************************************************/
-void ixp2000_acquire_slowport(struct slowport_cfg *new_cfg, struct slowport_cfg *old_cfg)
-{
-	spin_lock_irqsave(&ixp2000_slowport_lock, ixp2000_slowport_irq_flags);
-
-	old_cfg->CCR = *IXP2000_SLOWPORT_CCR;
-	old_cfg->WTC = *IXP2000_SLOWPORT_WTC2;
-	old_cfg->RTC = *IXP2000_SLOWPORT_RTC2;
-	old_cfg->PCR = *IXP2000_SLOWPORT_PCR;
-	old_cfg->ADC = *IXP2000_SLOWPORT_ADC;
-
-	ixp2000_reg_write(IXP2000_SLOWPORT_CCR, new_cfg->CCR);
-	ixp2000_reg_write(IXP2000_SLOWPORT_WTC2, new_cfg->WTC);
-	ixp2000_reg_write(IXP2000_SLOWPORT_RTC2, new_cfg->RTC);
-	ixp2000_reg_write(IXP2000_SLOWPORT_PCR, new_cfg->PCR);
-	ixp2000_reg_wrb(IXP2000_SLOWPORT_ADC, new_cfg->ADC);
-}
-
-void ixp2000_release_slowport(struct slowport_cfg *old_cfg)
-{
-	ixp2000_reg_write(IXP2000_SLOWPORT_CCR, old_cfg->CCR);
-	ixp2000_reg_write(IXP2000_SLOWPORT_WTC2, old_cfg->WTC);
-	ixp2000_reg_write(IXP2000_SLOWPORT_RTC2, old_cfg->RTC);
-	ixp2000_reg_write(IXP2000_SLOWPORT_PCR, old_cfg->PCR);
-	ixp2000_reg_wrb(IXP2000_SLOWPORT_ADC, old_cfg->ADC);
-
-	spin_unlock_irqrestore(&ixp2000_slowport_lock, 
-					ixp2000_slowport_irq_flags);
-}
-
-/*************************************************************************
- * Chip specific mappings shared by all IXP2000 systems
- *************************************************************************/
-static struct map_desc ixp2000_io_desc[] __initdata = {
-	{
-		.virtual	= IXP2000_CAP_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_CAP_PHYS_BASE),
-		.length		= IXP2000_CAP_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_INTCTL_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_INTCTL_PHYS_BASE),
-		.length		= IXP2000_INTCTL_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_PCI_CREG_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_PCI_CREG_PHYS_BASE),
-		.length		= IXP2000_PCI_CREG_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_PCI_CSR_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_PCI_CSR_PHYS_BASE),
-		.length		= IXP2000_PCI_CSR_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_MSF_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_MSF_PHYS_BASE),
-		.length		= IXP2000_MSF_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_SCRATCH_RING_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_SCRATCH_RING_PHYS_BASE),
-		.length		= IXP2000_SCRATCH_RING_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_SRAM0_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_SRAM0_PHYS_BASE),
-		.length		= IXP2000_SRAM0_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_PCI_IO_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_PCI_IO_PHYS_BASE),
-		.length		= IXP2000_PCI_IO_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_PCI_CFG0_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_PCI_CFG0_PHYS_BASE),
-		.length		= IXP2000_PCI_CFG0_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= IXP2000_PCI_CFG1_VIRT_BASE,
-		.pfn		= __phys_to_pfn(IXP2000_PCI_CFG1_PHYS_BASE),
-		.length		= IXP2000_PCI_CFG1_SIZE,
-		.type		= MT_DEVICE,
-	}
-};
-
-void __init ixp2000_map_io(void)
-{
-	iotable_init(ixp2000_io_desc, ARRAY_SIZE(ixp2000_io_desc));
-
-	/* Set slowport to 8-bit mode.  */
-	ixp2000_reg_wrb(IXP2000_SLOWPORT_FRM, 1);
-}
-
-
-/*************************************************************************
- * Serial port support for IXP2000
- *************************************************************************/
-static struct plat_serial8250_port ixp2000_serial_port[] = {
-	{
-		.mapbase	= IXP2000_UART_PHYS_BASE,
-		.membase	= (char *)(IXP2000_UART_VIRT_BASE + 3),
-		.irq		= IRQ_IXP2000_UART,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= 50000000,
-	},
-	{ },
-};
-
-static struct resource ixp2000_uart_resource = {
-	.start		= IXP2000_UART_PHYS_BASE,
-	.end		= IXP2000_UART_PHYS_BASE + 0x1f,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device ixp2000_serial_device = {
-	.name		= "serial8250",
-	.id		= PLAT8250_DEV_PLATFORM,
-	.dev		= {
-		.platform_data		= ixp2000_serial_port,
-	},
-	.num_resources	= 1,
-	.resource	= &ixp2000_uart_resource,
-};
-
-void __init ixp2000_uart_init(void)
-{
-	platform_device_register(&ixp2000_serial_device);
-}
-
-
-/*************************************************************************
- * Timer-tick functions for IXP2000
- *************************************************************************/
-static unsigned ticks_per_jiffy;
-static unsigned ticks_per_usec;
-static unsigned next_jiffy_time;
-static volatile unsigned long *missing_jiffy_timer_csr;
-
-unsigned long ixp2000_gettimeoffset (void)
-{
- 	unsigned long offset;
-
-	offset = next_jiffy_time - *missing_jiffy_timer_csr;
-
-	return offset / ticks_per_usec;
-}
-
-static irqreturn_t ixp2000_timer_interrupt(int irq, void *dev_id)
-{
-	/* clear timer 1 */
-	ixp2000_reg_wrb(IXP2000_T1_CLR, 1);
-
-	while ((signed long)(next_jiffy_time - *missing_jiffy_timer_csr)
-							>= ticks_per_jiffy) {
-		timer_tick();
-		next_jiffy_time -= ticks_per_jiffy;
-	}
-
-	return IRQ_HANDLED;
-}
-
-static struct irqaction ixp2000_timer_irq = {
-	.name		= "IXP2000 Timer Tick",
-	.flags		= IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
-	.handler	= ixp2000_timer_interrupt,
-};
-
-void __init ixp2000_init_time(unsigned long tick_rate)
-{
-	ticks_per_jiffy = (tick_rate + HZ/2) / HZ;
-	ticks_per_usec = tick_rate / 1000000;
-
-	/*
-	 * We use timer 1 as our timer interrupt.
-	 */
-	ixp2000_reg_write(IXP2000_T1_CLR, 0);
-	ixp2000_reg_write(IXP2000_T1_CLD, ticks_per_jiffy - 1);
-	ixp2000_reg_write(IXP2000_T1_CTL, (1 << 7));
-
-	/*
-	 * We use a second timer as a monotonic counter for tracking
-	 * missed jiffies.  The IXP2000 has four timers, but if we're
-	 * on an A-step IXP2800, timer 2 and 3 don't work, so on those
-	 * chips we use timer 4.  Timer 4 is the only timer that can
-	 * be used for the watchdog, so we use timer 2 if we're on a
-	 * non-buggy chip.
-	 */
-	if ((*IXP2000_PRODUCT_ID & 0x001ffef0) == 0x00000000) {
-		printk(KERN_INFO "Enabling IXP2800 erratum #25 workaround\n");
-
-		ixp2000_reg_write(IXP2000_T4_CLR, 0);
-		ixp2000_reg_write(IXP2000_T4_CLD, -1);
-		ixp2000_reg_wrb(IXP2000_T4_CTL, (1 << 7));
-		missing_jiffy_timer_csr = IXP2000_T4_CSR;
-	} else {
-		ixp2000_reg_write(IXP2000_T2_CLR, 0);
-		ixp2000_reg_write(IXP2000_T2_CLD, -1);
-		ixp2000_reg_wrb(IXP2000_T2_CTL, (1 << 7));
-		missing_jiffy_timer_csr = IXP2000_T2_CSR;
-	}
- 	next_jiffy_time = 0xffffffff;
-
-	/* register for interrupt */
-	setup_irq(IRQ_IXP2000_TIMER1, &ixp2000_timer_irq);
-}
-
-/*************************************************************************
- * GPIO helpers
- *************************************************************************/
-static unsigned long GPIO_IRQ_falling_edge;
-static unsigned long GPIO_IRQ_rising_edge;
-static unsigned long GPIO_IRQ_level_low;
-static unsigned long GPIO_IRQ_level_high;
-
-static void update_gpio_int_csrs(void)
-{
-	ixp2000_reg_write(IXP2000_GPIO_FEDR, GPIO_IRQ_falling_edge);
-	ixp2000_reg_write(IXP2000_GPIO_REDR, GPIO_IRQ_rising_edge);
-	ixp2000_reg_write(IXP2000_GPIO_LSLR, GPIO_IRQ_level_low);
-	ixp2000_reg_wrb(IXP2000_GPIO_LSHR, GPIO_IRQ_level_high);
-}
-
-void gpio_line_config(int line, int direction)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	if (direction == GPIO_OUT) {
-		/* if it's an output, it ain't an interrupt anymore */
-		GPIO_IRQ_falling_edge &= ~(1 << line);
-		GPIO_IRQ_rising_edge &= ~(1 << line);
-		GPIO_IRQ_level_low &= ~(1 << line);
-		GPIO_IRQ_level_high &= ~(1 << line);
-		update_gpio_int_csrs();
-
-		ixp2000_reg_wrb(IXP2000_GPIO_PDSR, 1 << line);
-	} else if (direction == GPIO_IN) {
-		ixp2000_reg_wrb(IXP2000_GPIO_PDCR, 1 << line);
-	}
-	local_irq_restore(flags);
-}
-EXPORT_SYMBOL(gpio_line_config);
-
-
-/*************************************************************************
- * IRQ handling IXP2000
- *************************************************************************/
-static void ixp2000_GPIO_irq_handler(unsigned int irq, struct irq_desc *desc)
-{                               
-	int i;
-	unsigned long status = *IXP2000_GPIO_INST;
-		   
-	for (i = 0; i <= 7; i++) {
-		if (status & (1<<i)) {
-			generic_handle_irq(i + IRQ_IXP2000_GPIO0);
-		}
-	}
-}
-
-static int ixp2000_GPIO_irq_type(struct irq_data *d, unsigned int type)
-{
-	int line = d->irq - IRQ_IXP2000_GPIO0;
-
-	/*
-	 * First, configure this GPIO line as an input.
-	 */
-	ixp2000_reg_write(IXP2000_GPIO_PDCR, 1 << line);
-
-	/*
-	 * Then, set the proper trigger type.
-	 */
-	if (type & IRQ_TYPE_EDGE_FALLING)
-		GPIO_IRQ_falling_edge |= 1 << line;
-	else
-		GPIO_IRQ_falling_edge &= ~(1 << line);
-	if (type & IRQ_TYPE_EDGE_RISING)
-		GPIO_IRQ_rising_edge |= 1 << line;
-	else
-		GPIO_IRQ_rising_edge &= ~(1 << line);
-	if (type & IRQ_TYPE_LEVEL_LOW)
-		GPIO_IRQ_level_low |= 1 << line;
-	else
-		GPIO_IRQ_level_low &= ~(1 << line);
-	if (type & IRQ_TYPE_LEVEL_HIGH)
-		GPIO_IRQ_level_high |= 1 << line;
-	else
-		GPIO_IRQ_level_high &= ~(1 << line);
-	update_gpio_int_csrs();
-
-	return 0;
-}
-
-static void ixp2000_GPIO_irq_mask_ack(struct irq_data *d)
-{
-	unsigned int irq = d->irq;
-
-	ixp2000_reg_write(IXP2000_GPIO_INCR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-
-	ixp2000_reg_write(IXP2000_GPIO_EDSR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-	ixp2000_reg_write(IXP2000_GPIO_LDSR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-	ixp2000_reg_wrb(IXP2000_GPIO_INST, (1 << (irq - IRQ_IXP2000_GPIO0)));
-}
-
-static void ixp2000_GPIO_irq_mask(struct irq_data *d)
-{
-	unsigned int irq = d->irq;
-
-	ixp2000_reg_wrb(IXP2000_GPIO_INCR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-}
-
-static void ixp2000_GPIO_irq_unmask(struct irq_data *d)
-{
-	unsigned int irq = d->irq;
-
-	ixp2000_reg_write(IXP2000_GPIO_INSR, (1 << (irq - IRQ_IXP2000_GPIO0)));
-}
-
-static struct irq_chip ixp2000_GPIO_irq_chip = {
-	.irq_ack	= ixp2000_GPIO_irq_mask_ack,
-	.irq_mask	= ixp2000_GPIO_irq_mask,
-	.irq_unmask	= ixp2000_GPIO_irq_unmask,
-	.irq_set_type	= ixp2000_GPIO_irq_type,
-};
-
-static void ixp2000_pci_irq_mask(struct irq_data *d)
-{
-	unsigned long temp = *IXP2000_PCI_XSCALE_INT_ENABLE;
-	if (d->irq == IRQ_IXP2000_PCIA)
-		ixp2000_reg_wrb(IXP2000_PCI_XSCALE_INT_ENABLE, (temp & ~(1 << 26)));
-	else if (d->irq == IRQ_IXP2000_PCIB)
-		ixp2000_reg_wrb(IXP2000_PCI_XSCALE_INT_ENABLE, (temp & ~(1 << 27)));
-}
-
-static void ixp2000_pci_irq_unmask(struct irq_data *d)
-{
-	unsigned long temp = *IXP2000_PCI_XSCALE_INT_ENABLE;
-	if (d->irq == IRQ_IXP2000_PCIA)
-		ixp2000_reg_write(IXP2000_PCI_XSCALE_INT_ENABLE, (temp | (1 << 26)));
-	else if (d->irq == IRQ_IXP2000_PCIB)
-		ixp2000_reg_write(IXP2000_PCI_XSCALE_INT_ENABLE, (temp | (1 << 27)));
-}
-
-/*
- * Error interrupts. These are used extensively by the microengine drivers
- */
-static void ixp2000_err_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	int i;
-	unsigned long status = *IXP2000_IRQ_ERR_STATUS;
-
-	for(i = 31; i >= 0; i--) {
-		if(status & (1 << i)) {
-			generic_handle_irq(IRQ_IXP2000_DRAM0_MIN_ERR + i);
-		}
-	}
-}
-
-static void ixp2000_err_irq_mask(struct irq_data *d)
-{
-	ixp2000_reg_write(IXP2000_IRQ_ERR_ENABLE_CLR,
-			(1 << (d->irq - IRQ_IXP2000_DRAM0_MIN_ERR)));
-}
-
-static void ixp2000_err_irq_unmask(struct irq_data *d)
-{
-	ixp2000_reg_write(IXP2000_IRQ_ERR_ENABLE_SET,
-			(1 << (d->irq - IRQ_IXP2000_DRAM0_MIN_ERR)));
-}
-
-static struct irq_chip ixp2000_err_irq_chip = {
-	.irq_ack	= ixp2000_err_irq_mask,
-	.irq_mask	= ixp2000_err_irq_mask,
-	.irq_unmask	= ixp2000_err_irq_unmask
-};
-
-static struct irq_chip ixp2000_pci_irq_chip = {
-	.irq_ack	= ixp2000_pci_irq_mask,
-	.irq_mask	= ixp2000_pci_irq_mask,
-	.irq_unmask	= ixp2000_pci_irq_unmask
-};
-
-static void ixp2000_irq_mask(struct irq_data *d)
-{
-	ixp2000_reg_wrb(IXP2000_IRQ_ENABLE_CLR, (1 << d->irq));
-}
-
-static void ixp2000_irq_unmask(struct irq_data *d)
-{
-	ixp2000_reg_write(IXP2000_IRQ_ENABLE_SET, (1 << d->irq));
-}
-
-static struct irq_chip ixp2000_irq_chip = {
-	.irq_ack	= ixp2000_irq_mask,
-	.irq_mask	= ixp2000_irq_mask,
-	.irq_unmask	= ixp2000_irq_unmask
-};
-
-void __init ixp2000_init_irq(void)
-{
-	int irq;
-
-	/*
-	 * Mask all sources
-	 */
-	ixp2000_reg_write(IXP2000_IRQ_ENABLE_CLR, 0xffffffff);
-	ixp2000_reg_write(IXP2000_FIQ_ENABLE_CLR, 0xffffffff);
-
-	/* clear all GPIO edge/level detects */
-	ixp2000_reg_write(IXP2000_GPIO_REDR, 0);
-	ixp2000_reg_write(IXP2000_GPIO_FEDR, 0);
-	ixp2000_reg_write(IXP2000_GPIO_LSHR, 0);
-	ixp2000_reg_write(IXP2000_GPIO_LSLR, 0);
-	ixp2000_reg_write(IXP2000_GPIO_INCR, -1);
-
-	/* clear PCI interrupt sources */
-	ixp2000_reg_wrb(IXP2000_PCI_XSCALE_INT_ENABLE, 0);
-
-	/*
-	 * Certain bits in the IRQ status register of the 
-	 * IXP2000 are reserved. Instead of trying to map
-	 * things non 1:1 from bit position to IRQ number,
-	 * we mark the reserved IRQs as invalid. This makes
-	 * our mask/unmask code much simpler.
-	 */
-	for (irq = IRQ_IXP2000_SOFT_INT; irq <= IRQ_IXP2000_THDB3; irq++) {
-		if ((1 << irq) & IXP2000_VALID_IRQ_MASK) {
-			irq_set_chip_and_handler(irq, &ixp2000_irq_chip,
-						 handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID);
-		} else set_irq_flags(irq, 0);
-	}
-
-	for (irq = IRQ_IXP2000_DRAM0_MIN_ERR; irq <= IRQ_IXP2000_SP_INT; irq++) {
-		if((1 << (irq - IRQ_IXP2000_DRAM0_MIN_ERR)) &
-				IXP2000_VALID_ERR_IRQ_MASK) {
-			irq_set_chip_and_handler(irq, &ixp2000_err_irq_chip,
-						 handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID);
-		}
-		else
-			set_irq_flags(irq, 0);
-	}
-	irq_set_chained_handler(IRQ_IXP2000_ERRSUM, ixp2000_err_irq_handler);
-
-	for (irq = IRQ_IXP2000_GPIO0; irq <= IRQ_IXP2000_GPIO7; irq++) {
-		irq_set_chip_and_handler(irq, &ixp2000_GPIO_irq_chip,
-					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID);
-	}
-	irq_set_chained_handler(IRQ_IXP2000_GPIO, ixp2000_GPIO_irq_handler);
-
-	/*
-	 * Enable PCI irqs.  The actual PCI[AB] decoding is done in
-	 * entry-macro.S, so we don't need a chained handler for the
-	 * PCI interrupt source.
-	 */
-	ixp2000_reg_write(IXP2000_IRQ_ENABLE_SET, (1 << IRQ_IXP2000_PCI));
-	for (irq = IRQ_IXP2000_PCIA; irq <= IRQ_IXP2000_PCIB; irq++) {
-		irq_set_chip_and_handler(irq, &ixp2000_pci_irq_chip,
-					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID);
-	}
-}
-
-void ixp2000_restart(char mode, const char *cmd)
-{
-	ixp2000_reg_wrb(IXP2000_RESET0, RSTALL);
-}
diff --git a/arch/arm/mach-ixp2000/enp2611.c b/arch/arm/mach-ixp2000/enp2611.c
deleted file mode 100644
index 4867f40..0000000
--- a/arch/arm/mach-ixp2000/enp2611.c
+++ /dev/null
@@ -1,265 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/enp2611.c
- *
- * Radisys ENP-2611 support.
- *
- * Created 2004 by Lennert Buytenhek from the ixdp2x01 code.  The
- * original version carries the following notices:
- *
- * Original Author: Andrzej Mialkowski <andrzej.mialkowski@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002-2003 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_core.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-/*************************************************************************
- * ENP-2611 timer tick configuration
- *************************************************************************/
-static void __init enp2611_timer_init(void)
-{
-	ixp2000_init_time(50 * 1000 * 1000);
-}
-
-static struct sys_timer enp2611_timer = {
-	.init		= enp2611_timer_init,
-	.offset		= ixp2000_gettimeoffset,
-};
-
-
-/*************************************************************************
- * ENP-2611 I/O
- *************************************************************************/
-static struct map_desc enp2611_io_desc[] __initdata = {
-	{
-		.virtual	= ENP2611_CALEB_VIRT_BASE,
-		.pfn		= __phys_to_pfn(ENP2611_CALEB_PHYS_BASE),
-		.length		= ENP2611_CALEB_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= ENP2611_PM3386_0_VIRT_BASE,
-		.pfn		= __phys_to_pfn(ENP2611_PM3386_0_PHYS_BASE),
-		.length		= ENP2611_PM3386_0_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= ENP2611_PM3386_1_VIRT_BASE,
-		.pfn		= __phys_to_pfn(ENP2611_PM3386_1_PHYS_BASE),
-		.length		= ENP2611_PM3386_1_SIZE,
-		.type		= MT_DEVICE,
-	}
-};
-
-void __init enp2611_map_io(void)
-{
-	ixp2000_map_io();
-	iotable_init(enp2611_io_desc, ARRAY_SIZE(enp2611_io_desc));
-}
-
-
-/*************************************************************************
- * ENP-2611 PCI
- *************************************************************************/
-static int enp2611_pci_setup(int nr, struct pci_sys_data *sys)
-{
-	sys->mem_offset = 0xe0000000;
-	ixp2000_pci_setup(nr, sys);
-	return 1;
-}
-
-static void __init enp2611_pci_preinit(void)
-{
-	ixp2000_reg_write(IXP2000_PCI_ADDR_EXT, 0x00100000);
-	ixp2000_pci_preinit();
-	pcibios_setup("firmware");
-}
-
-static inline int enp2611_pci_valid_device(struct pci_bus *bus,
-						unsigned int devfn)
-{
-	/* The 82559 ethernet controller appears at both PCI:1:0:0 and
-	 * PCI:1:2:0, so let's pretend the second one isn't there.
-	 */
-	if (bus->number == 0x01 && devfn == 0x10)
-		return 0;
-
-	return 1;
-}
-
-static int enp2611_pci_read_config(struct pci_bus *bus, unsigned int devfn,
-					int where, int size, u32 *value)
-{
-	if (enp2611_pci_valid_device(bus, devfn))
-		return ixp2000_pci_read_config(bus, devfn, where, size, value);
-
-	return PCIBIOS_DEVICE_NOT_FOUND;
-}
-
-static int enp2611_pci_write_config(struct pci_bus *bus, unsigned int devfn,
-					int where, int size, u32 value)
-{
-	if (enp2611_pci_valid_device(bus, devfn))
-		return ixp2000_pci_write_config(bus, devfn, where, size, value);
-
-	return PCIBIOS_DEVICE_NOT_FOUND;
-}
-
-static struct pci_ops enp2611_pci_ops = {
-	.read   = enp2611_pci_read_config,
-	.write  = enp2611_pci_write_config
-};
-
-static struct pci_bus * __init enp2611_pci_scan_bus(int nr,
-						struct pci_sys_data *sys)
-{
-	return pci_scan_root_bus(NULL, sys->busnr, &enp2611_pci_ops, sys,
-				 &sys->resources);
-}
-
-static int __init enp2611_pci_map_irq(const struct pci_dev *dev, u8 slot,
-	u8 pin)
-{
-	int irq;
-
-	if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 0) {
-		/* IXP2400. */
-		irq = IRQ_IXP2000_PCIA;
-	} else if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 1) {
-		/* 21555 non-transparent bridge.  */
-		irq = IRQ_IXP2000_PCIB;
-	} else if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 4) {
-		/* PCI2050B transparent bridge.  */
-		irq = -1;
-	} else if (dev->bus->number == 1 && PCI_SLOT(dev->devfn) == 0) {
-		/* 82559 ethernet.  */
-		irq = IRQ_IXP2000_PCIA;
-	} else if (dev->bus->number == 1 && PCI_SLOT(dev->devfn) == 1) {
-		/* SPI-3 option board.  */
-		irq = IRQ_IXP2000_PCIB;
-	} else {
-		printk(KERN_ERR "enp2611_pci_map_irq() called for unknown "
-				"device PCI:%d:%d:%d\n", dev->bus->number,
-				PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
-		irq = -1;
-	}
-
-	return irq;
-}
-
-struct hw_pci enp2611_pci __initdata = {
-	.nr_controllers	= 1,
-	.setup		= enp2611_pci_setup,
-	.preinit	= enp2611_pci_preinit,
-	.scan		= enp2611_pci_scan_bus,
-	.map_irq	= enp2611_pci_map_irq,
-};
-
-int __init enp2611_pci_init(void)
-{
-	if (machine_is_enp2611())
-		pci_common_init(&enp2611_pci);
-
-	return 0;
-}
-
-subsys_initcall(enp2611_pci_init);
-
-
-/*************************************************************************
- * ENP-2611 Machine Initialization
- *************************************************************************/
-static struct flash_platform_data enp2611_flash_platform_data = {
-	.map_name	= "cfi_probe",
-	.width		= 1,
-};
-
-static struct ixp2000_flash_data enp2611_flash_data = {
-	.platform_data	= &enp2611_flash_platform_data,
-	.nr_banks	= 1
-};
-
-static struct resource enp2611_flash_resource = {
-	.start		= 0xc4000000,
-	.end		= 0xc4000000 + 0x00ffffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device enp2611_flash = {
-	.name		= "IXP2000-Flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &enp2611_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &enp2611_flash_resource,
-};
-
-static struct ixp2000_i2c_pins enp2611_i2c_gpio_pins = {
-	.sda_pin	= ENP2611_GPIO_SDA,
-	.scl_pin	= ENP2611_GPIO_SCL,
-};
-
-static struct platform_device enp2611_i2c_controller = {
-	.name		= "IXP2000-I2C",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &enp2611_i2c_gpio_pins
-	},
-	.num_resources	= 0
-};
-
-static struct platform_device *enp2611_devices[] __initdata = {
-	&enp2611_flash,
-	&enp2611_i2c_controller
-};
-
-static void __init enp2611_init_machine(void)
-{
-	platform_add_devices(enp2611_devices, ARRAY_SIZE(enp2611_devices));
-	ixp2000_uart_init();
-}
-
-
-MACHINE_START(ENP2611, "Radisys ENP-2611 PCI network processor board")
-	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.atag_offset	= 0x100,
-	.map_io		= enp2611_map_io,
-	.init_irq	= ixp2000_init_irq,
-	.timer		= &enp2611_timer,
-	.init_machine	= enp2611_init_machine,
-	.restart	= ixp2000_restart,
-MACHINE_END
-
-
diff --git a/arch/arm/mach-ixp2000/include/mach/debug-macro.S b/arch/arm/mach-ixp2000/include/mach/debug-macro.S
deleted file mode 100644
index bdd3ccd..0000000
--- a/arch/arm/mach-ixp2000/include/mach/debug-macro.S
+++ /dev/null
@@ -1,25 +0,0 @@
-/* arch/arm/mach-ixp2000/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- *  Copyright (C) 1994-1999 Russell King
- *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
-		.macro  addruart, rp, rv, tmp
-		mov	\rp, #0x00030000
-#ifdef	__ARMEB__
-		orr	\rp, \rp, #0x00000003
-#endif
-		orr	\rv, \rp, #0xfe000000	@ virtual base
-		orr	\rv, \rv, #0x00f00000
-		orr	\rp, \rp, #0xc0000000	@ Physical base
-		.endm
-
-#define UART_SHIFT	2
-#include <asm/hardware/debug-8250.S>
diff --git a/arch/arm/mach-ixp2000/include/mach/enp2611.h b/arch/arm/mach-ixp2000/include/mach/enp2611.h
deleted file mode 100644
index 9ce3690..0000000
--- a/arch/arm/mach-ixp2000/include/mach/enp2611.h
+++ /dev/null
@@ -1,46 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/enp2611.h
- *
- * Register and other defines for Radisys ENP-2611
- *
- * Created 2004 by Lennert Buytenhek from the ixdp2x01 code.  The
- * original version carries the following notices:
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-
-#ifndef __ENP2611_H
-#define __ENP2611_H
-
-#define ENP2611_CALEB_PHYS_BASE		0xc5000000
-#define ENP2611_CALEB_VIRT_BASE		0xfe000000
-#define ENP2611_CALEB_SIZE		0x00100000
-
-#define ENP2611_PM3386_0_PHYS_BASE	0xc6000000
-#define ENP2611_PM3386_0_VIRT_BASE	0xfe100000
-#define ENP2611_PM3386_0_SIZE		0x00100000
-
-#define ENP2611_PM3386_1_PHYS_BASE	0xc6400000
-#define ENP2611_PM3386_1_VIRT_BASE	0xfe200000
-#define ENP2611_PM3386_1_SIZE		0x00100000
-
-#define ENP2611_GPIO_SCL		7
-#define ENP2611_GPIO_SDA		6
-
-#define IRQ_ENP2611_THERMAL		IRQ_IXP2000_GPIO4
-#define IRQ_ENP2611_OPTION_BOARD	IRQ_IXP2000_GPIO3
-#define IRQ_ENP2611_CALEB		IRQ_IXP2000_GPIO2
-#define IRQ_ENP2611_PM3386_1		IRQ_IXP2000_GPIO1
-#define IRQ_ENP2611_PM3386_0		IRQ_IXP2000_GPIO0
-
-
-#endif
diff --git a/arch/arm/mach-ixp2000/include/mach/entry-macro.S b/arch/arm/mach-ixp2000/include/mach/entry-macro.S
deleted file mode 100644
index c4444df..0000000
--- a/arch/arm/mach-ixp2000/include/mach/entry-macro.S
+++ /dev/null
@@ -1,54 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for IXP2000-based platforms
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <mach/irqs.h>
-
-		.macro  get_irqnr_preamble, base, tmp
-		.endm
-
-		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-		mov	\irqnr, #0x0              @clear out irqnr as default
-                mov	\base, #0xfe000000
-		orr	\base, \base, #0x00e00000
-		orr	\base, \base, #0x08
-		ldr	\irqstat, [\base]         @ get interrupts
-
-		cmp	\irqstat, #0
-		beq	1001f
-
-		clz     \irqnr, \irqstat
-		mov     \base, #31
-		subs    \irqnr, \base, \irqnr
-
-		/*
-		 * We handle PCIA and PCIB here so we don't have an
-		 * extra layer of code just to check these two bits.
-		 */
-		cmp	\irqnr, #IRQ_IXP2000_PCI
-		bne	1001f
-
-		mov	\base, #0xfe000000
-		orr	\base, \base, #0x00c00000
-		orr	\base, \base, #0x00000100
-		orr	\base, \base, #0x00000058
-		ldr	\irqstat, [\base]
-
-		mov	\tmp, #(1<<26)
-		tst	\irqstat, \tmp
-		movne	\irqnr, #IRQ_IXP2000_PCIA
-		bne	1001f
-
-		mov	\tmp, #(1<<27)
-		tst	\irqstat, \tmp
-		movne	\irqnr, #IRQ_IXP2000_PCIB
-
-1001:
-		.endm
-
diff --git a/arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h b/arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h
deleted file mode 100644
index af836c7..0000000
--- a/arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/gpio.h
- *
- * Copyright (C) 2002 Intel Corporation.
- *
- * This program is free software, you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/*
- * IXP2000 GPIO in/out, edge/level detection for IRQs:
- * IRQs are generated on Falling-edge, Rising-Edge, Level-low, Level-High
- * or both Falling-edge and Rising-edge.
- * This must be called *before* the corresponding IRQ is registerd.
- * Use this instead of directly setting the GPIO registers.
- * GPIOs may also be used as GPIOs (e.g. for emulating i2c/smb)
- */
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#ifndef __ASSEMBLY__
-
-#define GPIO_IN				0
-#define GPIO_OUT			1
-
-#define IXP2000_GPIO_LOW		0
-#define IXP2000_GPIO_HIGH		1
-
-extern void gpio_line_config(int line, int direction);
-
-static inline int gpio_line_get(int line)
-{
-	return (((*IXP2000_GPIO_PLR) >> line) & 1);
-}
-
-static inline void gpio_line_set(int line, int value)
-{
-	if (value == IXP2000_GPIO_HIGH) {
-		ixp2000_reg_write(IXP2000_GPIO_POSR, 1 << line);
-	} else if (value == IXP2000_GPIO_LOW) {
-		ixp2000_reg_write(IXP2000_GPIO_POCR, 1 << line);
-	}
-}
-
-#endif /* !__ASSEMBLY__ */
-
-#endif /* ASM_ARCH_IXP2000_GPIO_H_ */
diff --git a/arch/arm/mach-ixp2000/include/mach/hardware.h b/arch/arm/mach-ixp2000/include/mach/hardware.h
deleted file mode 100644
index cdaf1db..0000000
--- a/arch/arm/mach-ixp2000/include/mach/hardware.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/hardware.h
- *
- * Hardware definitions for IXP2400/2800 based systems
- *
- * Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
- *
- * Maintainer: Deepak Saxena <dsaxena@mvista.com>
- *
- * Copyright (C) 2001-2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H__
-#define __ASM_ARCH_HARDWARE_H__
-
-#include "ixp2000-regs.h"	/* Chipset Registers */
-
-/*
- * Platform helper functions
- */
-#include "platform.h"
-
-/*
- * Platform-specific bits
- */
-#include "enp2611.h"		/* ENP-2611 */
-#include "ixdp2x00.h"		/* IXDP2400/2800 */
-#include "ixdp2x01.h"		/* IXDP2401/2801 */
-
-#endif  /* _ASM_ARCH_HARDWARE_H__ */
diff --git a/arch/arm/mach-ixp2000/include/mach/io.h b/arch/arm/mach-ixp2000/include/mach/io.h
deleted file mode 100644
index f6552d6..0000000
--- a/arch/arm/mach-ixp2000/include/mach/io.h
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/io.h
- *
- * Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002  Intel Corp.
- * Copyrgiht (C) 2003-2004 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#include <mach/hardware.h>
-
-#define IO_SPACE_LIMIT		0xffffffff
-
-/*
- * The A? revisions of the IXP2000s assert byte lanes for PCI I/O
- * transactions the other way round (MEM transactions don't have this
- * issue), so if we want to support those models, we need to override
- * the standard I/O functions.
- *
- * B0 and later have a bit that can be set to 1 to get the proper
- * behavior for I/O transactions, which then allows us to use the
- * standard I/O functions.  This is what we do if the user does not
- * explicitly ask for support for pre-B0.
- */
-#ifdef CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO
-#define ___io(p)		((void __iomem *)((p)+IXP2000_PCI_IO_VIRT_BASE))
-
-#define alignb(addr)		(void __iomem *)((unsigned long)(addr) ^ 3)
-#define alignw(addr)		(void __iomem *)((unsigned long)(addr) ^ 2)
-
-#define outb(v,p)		__raw_writeb((v),alignb(___io(p)))
-#define outw(v,p)		__raw_writew((v),alignw(___io(p)))
-#define outl(v,p)		__raw_writel((v),___io(p))
-
-#define inb(p)		({ unsigned int __v = __raw_readb(alignb(___io(p))); __v; })
-#define inw(p)		\
-	({ unsigned int __v = (__raw_readw(alignw(___io(p)))); __v; })
-#define inl(p)		\
-	({ unsigned int __v = (__raw_readl(___io(p))); __v; })
-
-#define outsb(p,d,l)		__raw_writesb(alignb(___io(p)),d,l)
-#define outsw(p,d,l)		__raw_writesw(alignw(___io(p)),d,l)
-#define outsl(p,d,l)		__raw_writesl(___io(p),d,l)
-
-#define insb(p,d,l)		__raw_readsb(alignb(___io(p)),d,l)
-#define insw(p,d,l)		__raw_readsw(alignw(___io(p)),d,l)
-#define insl(p,d,l)		__raw_readsl(___io(p),d,l)
-
-#define __is_io_address(p)	((((unsigned long)(p)) & ~(IXP2000_PCI_IO_SIZE - 1)) == IXP2000_PCI_IO_VIRT_BASE)
-
-#define ioread8(p)						\
-	({							\
-		unsigned int __v;				\
-								\
-		if (__is_io_address(p)) {			\
-			__v = __raw_readb(alignb(p));		\
-		} else {					\
-			__v = __raw_readb(p);			\
-		}						\
-								\
-		__v;						\
-	})							\
-
-#define ioread16(p)						\
-	({							\
-		unsigned int __v;				\
-								\
-		if (__is_io_address(p)) {			\
-			__v = __raw_readw(alignw(p));		\
-		} else {					\
-			__v = le16_to_cpu(__raw_readw(p));	\
-		}						\
-								\
-		__v;						\
-	})
-
-#define ioread32(p)						\
-	({							\
-		unsigned int __v;				\
-								\
-		if (__is_io_address(p)) {			\
-			__v = __raw_readl(p);			\
-		} else {					\
-			__v = le32_to_cpu(__raw_readl(p));	\
-		}						\
-								\
-		 __v;						\
-	})
-
-#define iowrite8(v,p)						\
-	({							\
-		if (__is_io_address(p)) {			\
-			__raw_writeb((v), alignb(p));		\
-		} else {					\
-			__raw_writeb((v), p);			\
-		}						\
-	})
-
-#define iowrite16(v,p)						\
-	({							\
-		if (__is_io_address(p)) {			\
-			__raw_writew((v), alignw(p));		\
-		} else {					\
-			__raw_writew(cpu_to_le16(v), p);	\
-		}						\
-	})
-
-#define iowrite32(v,p)						\
-	({							\
-		if (__is_io_address(p)) {			\
-			__raw_writel((v), p);			\
-		} else {					\
-			__raw_writel(cpu_to_le32(v), p);	\
-		}						\
-	})
-
-#define ioport_map(port, nr)	___io(port)
-
-#define ioport_unmap(addr)
-#else
-#define __io(p)			((void __iomem *)((p)+IXP2000_PCI_IO_VIRT_BASE))
-#endif
-
-
-#endif
diff --git a/arch/arm/mach-ixp2000/include/mach/irqs.h b/arch/arm/mach-ixp2000/include/mach/irqs.h
deleted file mode 100644
index bee96bc..0000000
--- a/arch/arm/mach-ixp2000/include/mach/irqs.h
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/irqs.h
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- * 
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef _IRQS_H
-#define _IRQS_H
-
-/*
- * Do NOT add #ifdef MACHINE_FOO in here.
- * Simpy add your machine IRQs here and increase NR_IRQS if needed to
- * hold your machine's IRQ table.
- */
-
-/*
- * Some interrupt numbers go unused b/c the IRQ mask/ummask/status
- * register has those bit reserved. We just mark those interrupts
- * as invalid and this allows us to do mask/unmask with a single
- * shift operation instead of having to map the IRQ number to
- * a HW IRQ number.
- */
-#define	IRQ_IXP2000_SOFT_INT		0 /* soft interrupt */
-#define	IRQ_IXP2000_ERRSUM		1 /* OR of all bits in ErrorStatus reg*/
-#define	IRQ_IXP2000_UART		2
-#define	IRQ_IXP2000_GPIO		3
-#define	IRQ_IXP2000_TIMER1     		4
-#define	IRQ_IXP2000_TIMER2     		5
-#define	IRQ_IXP2000_TIMER3     		6
-#define	IRQ_IXP2000_TIMER4     		7
-#define	IRQ_IXP2000_PMU        		8               
-#define	IRQ_IXP2000_SPF        		9  /* Slow port framer IRQ */
-#define	IRQ_IXP2000_DMA1      		10
-#define	IRQ_IXP2000_DMA2      		11
-#define	IRQ_IXP2000_DMA3      		12
-#define	IRQ_IXP2000_PCI_DOORBELL	13
-#define	IRQ_IXP2000_ME_ATTN       	14 
-#define	IRQ_IXP2000_PCI   		15 /* PCI INTA or INTB */
-#define	IRQ_IXP2000_THDA0   		16 /* thread 0-31A */
-#define	IRQ_IXP2000_THDA1  		17 /* thread 32-63A, IXP2800 only */
-#define	IRQ_IXP2000_THDA2		18 /* thread 64-95A */
-#define	IRQ_IXP2000_THDA3 		19 /* thread 96-127A, IXP2800 only */
-#define	IRQ_IXP2000_THDB0		24 /* thread 0-31B */
-#define	IRQ_IXP2000_THDB1		25 /* thread 32-63B, IXP2800 only */
-#define	IRQ_IXP2000_THDB2		26 /* thread 64-95B */
-#define	IRQ_IXP2000_THDB3		27 /* thread 96-127B, IXP2800 only */
-
-/* define generic GPIOs */
-#define IRQ_IXP2000_GPIO0		32
-#define IRQ_IXP2000_GPIO1		33
-#define IRQ_IXP2000_GPIO2		34
-#define IRQ_IXP2000_GPIO3		35
-#define IRQ_IXP2000_GPIO4		36
-#define IRQ_IXP2000_GPIO5		37
-#define IRQ_IXP2000_GPIO6		38
-#define IRQ_IXP2000_GPIO7		39
-
-/* split off the 2 PCI sources */
-#define IRQ_IXP2000_PCIA		40
-#define IRQ_IXP2000_PCIB		41
-
-/* Int sources from IRQ_ERROR_STATUS */
-#define IRQ_IXP2000_DRAM0_MIN_ERR	42
-#define IRQ_IXP2000_DRAM0_MAJ_ERR	43
-#define IRQ_IXP2000_DRAM1_MIN_ERR	44
-#define IRQ_IXP2000_DRAM1_MAJ_ERR	45
-#define IRQ_IXP2000_DRAM2_MIN_ERR	46
-#define IRQ_IXP2000_DRAM2_MAJ_ERR	47
-/* 48-57 reserved */
-#define IRQ_IXP2000_SRAM0_ERR		58
-#define IRQ_IXP2000_SRAM1_ERR		59
-#define IRQ_IXP2000_SRAM2_ERR		60
-#define IRQ_IXP2000_SRAM3_ERR		61
-/* 62-65 reserved */
-#define IRQ_IXP2000_MEDIA_ERR		66
-#define IRQ_IXP2000_PCI_ERR			67
-#define IRQ_IXP2000_SP_INT			68
-
-#define NR_IXP2000_IRQS				69
-
-#define	IXP2000_BOARD_IRQ(x)		(NR_IXP2000_IRQS + (x))
-
-#define	IXP2000_BOARD_IRQ_MASK(irq)	(1 << (irq - NR_IXP2000_IRQS))	
-
-#define IXP2000_ERR_IRQ_MASK(irq) ( 1 << (irq - IRQ_IXP2000_DRAM0_MIN_ERR))
-#define IXP2000_VALID_ERR_IRQ_MASK (\
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM0_MIN_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM0_MAJ_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM1_MIN_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM1_MAJ_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM2_MIN_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_DRAM2_MAJ_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM0_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM1_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM2_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SRAM3_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_MEDIA_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_PCI_ERR) | \
-		IXP2000_ERR_IRQ_MASK(IRQ_IXP2000_SP_INT)	)
-
-/*
- * This allows for all the on-chip sources plus up to 32 CPLD based
- * IRQs. Should be more than enough.
- */
-#define	IXP2000_BOARD_IRQS		32
-#define NR_IRQS				(NR_IXP2000_IRQS + IXP2000_BOARD_IRQS)
-
-
-/* 
- * IXDP2400 specific IRQs
- */
-#define	IRQ_IXDP2400_INGRESS_NPU	IXP2000_BOARD_IRQ(0) 
-#define	IRQ_IXDP2400_ENET		IXP2000_BOARD_IRQ(1) 
-#define	IRQ_IXDP2400_MEDIA_PCI		IXP2000_BOARD_IRQ(2) 
-#define	IRQ_IXDP2400_MEDIA_SP		IXP2000_BOARD_IRQ(3) 
-#define	IRQ_IXDP2400_SF_PCI		IXP2000_BOARD_IRQ(4) 
-#define	IRQ_IXDP2400_SF_SP		IXP2000_BOARD_IRQ(5) 
-#define	IRQ_IXDP2400_PMC		IXP2000_BOARD_IRQ(6) 
-#define	IRQ_IXDP2400_TVM		IXP2000_BOARD_IRQ(7) 
-
-#define	NR_IXDP2400_IRQS		((IRQ_IXDP2400_TVM)+1)  
-#define	IXDP2400_NR_IRQS		NR_IXDP2400_IRQS - NR_IXP2000_IRQS
-
-/* IXDP2800 specific IRQs */
-#define IRQ_IXDP2800_EGRESS_ENET	IXP2000_BOARD_IRQ(0)
-#define IRQ_IXDP2800_INGRESS_NPU	IXP2000_BOARD_IRQ(1)
-#define IRQ_IXDP2800_PMC		IXP2000_BOARD_IRQ(2)
-#define IRQ_IXDP2800_FABRIC_PCI		IXP2000_BOARD_IRQ(3)
-#define IRQ_IXDP2800_FABRIC		IXP2000_BOARD_IRQ(4)
-#define IRQ_IXDP2800_MEDIA		IXP2000_BOARD_IRQ(5)
-
-#define	NR_IXDP2800_IRQS		((IRQ_IXDP2800_MEDIA)+1)
-#define	IXDP2800_NR_IRQS		NR_IXDP2800_IRQS - NR_IXP2000_IRQS
-
-/* 
- * IRQs on both IXDP2x01 boards
- */
-#define IRQ_IXDP2X01_SPCI_DB_0		IXP2000_BOARD_IRQ(2)
-#define IRQ_IXDP2X01_SPCI_DB_1		IXP2000_BOARD_IRQ(3)
-#define IRQ_IXDP2X01_SPCI_PMC_INTA	IXP2000_BOARD_IRQ(4)
-#define IRQ_IXDP2X01_SPCI_PMC_INTB	IXP2000_BOARD_IRQ(5)
-#define IRQ_IXDP2X01_SPCI_PMC_INTC	IXP2000_BOARD_IRQ(6)
-#define IRQ_IXDP2X01_SPCI_PMC_INTD	IXP2000_BOARD_IRQ(7)
-#define IRQ_IXDP2X01_SPCI_FIC_INT	IXP2000_BOARD_IRQ(8)
-#define IRQ_IXDP2X01_IPMI_FROM		IXP2000_BOARD_IRQ(16)
-#define IRQ_IXDP2X01_125US		IXP2000_BOARD_IRQ(17)
-#define IRQ_IXDP2X01_DB_0_ADD		IXP2000_BOARD_IRQ(18)
-#define IRQ_IXDP2X01_DB_1_ADD		IXP2000_BOARD_IRQ(19)
-#define IRQ_IXDP2X01_UART1		IXP2000_BOARD_IRQ(21)
-#define IRQ_IXDP2X01_UART2		IXP2000_BOARD_IRQ(22)
-#define IRQ_IXDP2X01_FIC_ADD_INT	IXP2000_BOARD_IRQ(24)
-#define IRQ_IXDP2X01_CS8900		IXP2000_BOARD_IRQ(25)
-#define IRQ_IXDP2X01_BBSRAM		IXP2000_BOARD_IRQ(26)
-
-#define IXDP2X01_VALID_IRQ_MASK ( \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_DB_0) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_DB_1) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTA) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTB) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTC) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_PMC_INTD) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_SPCI_FIC_INT) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_IPMI_FROM) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_125US) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_DB_0_ADD) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_DB_1_ADD) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_UART1) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_UART2) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_FIC_ADD_INT) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_CS8900) | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2X01_BBSRAM) )
-
-/* 
- * IXDP2401 specific IRQs
- */
-#define IRQ_IXDP2401_INTA_82546		IXP2000_BOARD_IRQ(0)
-#define IRQ_IXDP2401_INTB_82546		IXP2000_BOARD_IRQ(1)
-
-#define	IXDP2401_VALID_IRQ_MASK ( \
-		IXDP2X01_VALID_IRQ_MASK | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2401_INTA_82546) |\
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2401_INTB_82546))
-
-/*
- * IXDP2801-specific IRQs
- */
-#define IRQ_IXDP2801_RIV		IXP2000_BOARD_IRQ(0)
-#define IRQ_IXDP2801_CNFG_MEDIA		IXP2000_BOARD_IRQ(27)
-#define IRQ_IXDP2801_CLOCK_REF		IXP2000_BOARD_IRQ(28)
-
-#define	IXDP2801_VALID_IRQ_MASK ( \
-		IXDP2X01_VALID_IRQ_MASK | \
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2801_RIV) |\
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2801_CNFG_MEDIA) |\
-		IXP2000_BOARD_IRQ_MASK(IRQ_IXDP2801_CLOCK_REF))
-
-#define	NR_IXDP2X01_IRQS		((IRQ_IXDP2801_CLOCK_REF) + 1)
-
-#endif /*_IRQS_H*/
diff --git a/arch/arm/mach-ixp2000/include/mach/ixdp2x00.h b/arch/arm/mach-ixp2000/include/mach/ixdp2x00.h
deleted file mode 100644
index 5df8479..0000000
--- a/arch/arm/mach-ixp2000/include/mach/ixdp2x00.h
+++ /dev/null
@@ -1,92 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/ixdp2x00.h
- *
- * Register and other defines for IXDP2[48]00 platforms
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-#ifndef _IXDP2X00_H_
-#define _IXDP2X00_H_
-
-/*
- * On board CPLD memory map
- */
-#define IXDP2X00_PHYS_CPLD_BASE		0xc7000000
-#define IXDP2X00_VIRT_CPLD_BASE		0xfe000000
-#define IXDP2X00_CPLD_SIZE		0x00100000
-
-
-#define IXDP2X00_CPLD_REG(x)  	\
-	(volatile unsigned long *)(IXDP2X00_VIRT_CPLD_BASE | x)
-
-/*
- * IXDP2400 CPLD registers
- */
-#define IXDP2400_CPLD_SYSLED		IXDP2X00_CPLD_REG(0x0)  
-#define IXDP2400_CPLD_DISP_DATA		IXDP2X00_CPLD_REG(0x4)
-#define IXDP2400_CPLD_CLOCK_SPEED	IXDP2X00_CPLD_REG(0x8)
-#define IXDP2400_CPLD_INT_STAT		IXDP2X00_CPLD_REG(0xc)
-#define IXDP2400_CPLD_REV		IXDP2X00_CPLD_REG(0x10)
-#define IXDP2400_CPLD_SYS_CLK_M		IXDP2X00_CPLD_REG(0x14)
-#define IXDP2400_CPLD_SYS_CLK_N		IXDP2X00_CPLD_REG(0x18)
-#define IXDP2400_CPLD_INT_MASK		IXDP2X00_CPLD_REG(0x48)
-
-/*
- * IXDP2800 CPLD registers
- */
-#define IXDP2800_CPLD_INT_STAT		IXDP2X00_CPLD_REG(0x0)
-#define IXDP2800_CPLD_INT_MASK		IXDP2X00_CPLD_REG(0x140)
-
-
-#define	IXDP2X00_GPIO_I2C_ENABLE	0x02
-#define	IXDP2X00_GPIO_SCL		0x07
-#define	IXDP2X00_GPIO_SDA		0x06
-
-/*
- * PCI devfns for on-board devices. We need these to be able to
- * properly translate IRQs and for device removal.
- */
-#define	IXDP2400_SLAVE_ENET_DEVFN	0x18	/* Bus 1 */
-#define	IXDP2400_MASTER_ENET_DEVFN	0x20	/* Bus 1 */
-#define	IXDP2400_MEDIA_DEVFN		0x28	/* Bus 1 */
-#define	IXDP2400_SWITCH_FABRIC_DEVFN	0x30	/* Bus 1 */
-
-#define	IXDP2800_SLAVE_ENET_DEVFN	0x20	/* Bus 1 */
-#define	IXDP2800_MASTER_ENET_DEVFN	0x18	/* Bus 1 */
-#define	IXDP2800_SWITCH_FABRIC_DEVFN	0x30	/* Bus 1 */
-
-#define	IXDP2X00_P2P_DEVFN		0x20	/* Bus 0 */
-#define	IXDP2X00_21555_DEVFN		0x30	/* Bus 0 */
-#define IXDP2X00_SLAVE_NPU_DEVFN	0x28	/* Bus 1 */
-#define	IXDP2X00_PMC_DEVFN		0x38	/* Bus 1 */
-#define IXDP2X00_MASTER_NPU_DEVFN	0x38	/* Bus 1 */
-
-#ifndef __ASSEMBLY__
-/*
- * The master NPU is always PCI master.
- */
-static inline unsigned int ixdp2x00_master_npu(void)
-{
-	return !!ixp2000_is_pcimaster();
-}
-
-/*
- * Helper functions used by ixdp2400 and ixdp2800 specific code
- */
-void ixdp2x00_init_irq(volatile unsigned long*, volatile unsigned long *, unsigned long);
-void ixdp2x00_slave_pci_postinit(void);
-void ixdp2x00_init_machine(void);
-void ixdp2x00_map_io(void);
-
-#endif
-
-#endif /*_IXDP2X00_H_ */
diff --git a/arch/arm/mach-ixp2000/include/mach/ixdp2x01.h b/arch/arm/mach-ixp2000/include/mach/ixdp2x01.h
deleted file mode 100644
index 4c1f040..0000000
--- a/arch/arm/mach-ixp2000/include/mach/ixdp2x01.h
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/ixdp2x01.h
- *
- * Platform definitions for IXDP2X01 && IXDP2801 systems
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2004 (c) MontaVista Software, Inc. 
- *
- * Based on original code Copyright (c) 2002-2003 Intel Corporation
- * 
- * This file is licensed under  the terms of the GNU General Public 
- * License version 2. This program is licensed "as is" without any 
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __IXDP2X01_H__
-#define __IXDP2X01_H__
-
-#define	IXDP2X01_PHYS_CPLD_BASE		0xc6024000
-#define	IXDP2X01_VIRT_CPLD_BASE		0xfe000000
-#define	IXDP2X01_CPLD_REGION_SIZE	0x00100000
-
-#define IXDP2X01_CPLD_VIRT_REG(reg) (volatile unsigned long*)(IXDP2X01_VIRT_CPLD_BASE | reg)
-#define IXDP2X01_CPLD_PHYS_REG(reg) (IXDP2X01_PHYS_CPLD_BASE | reg)
-
-#define IXDP2X01_UART1_VIRT_BASE	IXDP2X01_CPLD_VIRT_REG(0x40)
-#define IXDP2X01_UART1_PHYS_BASE	IXDP2X01_CPLD_PHYS_REG(0x40)
-
-#define IXDP2X01_UART2_VIRT_BASE	IXDP2X01_CPLD_VIRT_REG(0x60)
-#define IXDP2X01_UART2_PHYS_BASE	IXDP2X01_CPLD_PHYS_REG(0x60)
-
-#define IXDP2X01_CS8900_VIRT_BASE	IXDP2X01_CPLD_VIRT_REG(0x80)
-#define IXDP2X01_CS8900_VIRT_END	(IXDP2X01_CS8900_VIRT_BASE + 16)
-
-#define IXDP2X01_CPLD_RESET_REG         IXDP2X01_CPLD_VIRT_REG(0x00)
-#define IXDP2X01_INT_MASK_SET_REG	IXDP2X01_CPLD_VIRT_REG(0x08)
-#define IXDP2X01_INT_STAT_REG		IXDP2X01_CPLD_VIRT_REG(0x0C)
-#define IXDP2X01_INT_RAW_REG		IXDP2X01_CPLD_VIRT_REG(0x10) 
-#define IXDP2X01_INT_MASK_CLR_REG	IXDP2X01_INT_RAW_REG
-#define IXDP2X01_INT_SIM_REG		IXDP2X01_CPLD_VIRT_REG(0x14)
-
-#define IXDP2X01_CPLD_FLASH_REG		IXDP2X01_CPLD_VIRT_REG(0x20)
-
-#define IXDP2X01_CPLD_FLASH_INTERN 	0x8000
-#define IXDP2X01_CPLD_FLASH_BANK_MASK 	0xF
-#define IXDP2X01_FLASH_WINDOW_BITS 	25
-#define IXDP2X01_FLASH_WINDOW_SIZE 	(1 << IXDP2X01_FLASH_WINDOW_BITS)
-#define IXDP2X01_FLASH_WINDOW_MASK 	(IXDP2X01_FLASH_WINDOW_SIZE - 1)
-
-#define	IXDP2X01_UART_CLK		1843200
-
-#define	IXDP2X01_GPIO_I2C_ENABLE	0x02
-#define	IXDP2X01_GPIO_SCL		0x07
-#define	IXDP2X01_GPIO_SDA		0x06
-
-#endif /* __IXDP2x01_H__ */
diff --git a/arch/arm/mach-ixp2000/include/mach/ixp2000-regs.h b/arch/arm/mach-ixp2000/include/mach/ixp2000-regs.h
deleted file mode 100644
index 822f63f..0000000
--- a/arch/arm/mach-ixp2000/include/mach/ixp2000-regs.h
+++ /dev/null
@@ -1,451 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/ixp2000-regs.h
- *
- * Chipset register definitions for IXP2400/2800 based systems.
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- *
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-#ifndef _IXP2000_REGS_H_
-#define _IXP2000_REGS_H_
-
-/*
- * IXP2000 linux memory map:
- *
- * virt		phys		size
- * fb000000	db000000	16M		PCI CFG1
- * fc000000	da000000	16M		PCI CFG0
- * fd000000	d8000000	16M		PCI I/O
- * fe[0-7]00000			8M		per-platform mappings
- * fe900000	80000000	1M		SRAM #0 (first MB)
- * fea00000	cb400000	1M		SCRATCH ring get/put
- * feb00000	c8000000	1M		MSF
- * fec00000	df000000	1M		PCI CSRs
- * fed00000	de000000	1M		PCI CREG
- * fee00000	d6000000	1M		INTCTL
- * fef00000	c0000000	1M		CAP
- */
-
-/* 
- * Static I/O regions.
- *
- * Most of the registers are clumped in 4K regions spread throughout
- * the 0xc0000000 -> 0xc0100000 address range, but we just map in
- * the whole range using a single 1 MB section instead of small
- * 4K pages.
- *
- * CAP stands for CSR Access Proxy.
- *
- * If you change the virtual address of this mapping, please propagate
- * the change to arch/arm/kernel/debug.S, which hardcodes the virtual
- * address of the UART located in this region.
- */
-
-#define	IXP2000_CAP_PHYS_BASE		0xc0000000
-#define	IXP2000_CAP_VIRT_BASE		0xfef00000
-#define	IXP2000_CAP_SIZE		0x00100000
-
-/*
- * Addresses for specific on-chip peripherals.
- */
-#define	IXP2000_SLOWPORT_CSR_VIRT_BASE	0xfef80000
-#define	IXP2000_GLOBAL_REG_VIRT_BASE	0xfef04000
-#define	IXP2000_UART_PHYS_BASE		0xc0030000
-#define	IXP2000_UART_VIRT_BASE		0xfef30000
-#define	IXP2000_TIMER_VIRT_BASE		0xfef20000
-#define	IXP2000_UENGINE_CSR_VIRT_BASE	0xfef18000
-#define	IXP2000_GPIO_VIRT_BASE		0xfef10000
-
-/*
- * Devices outside of the 0xc0000000 -> 0xc0100000 range.  The virtual
- * addresses of the INTCTL and PCI_CSR mappings are hardcoded in
- * entry-macro.S, so if you ever change these please propagate
- * the change.
- */
-#define IXP2000_INTCTL_PHYS_BASE	0xd6000000
-#define	IXP2000_INTCTL_VIRT_BASE	0xfee00000
-#define	IXP2000_INTCTL_SIZE		0x00100000
-
-#define IXP2000_PCI_CREG_PHYS_BASE	0xde000000
-#define	IXP2000_PCI_CREG_VIRT_BASE	0xfed00000
-#define	IXP2000_PCI_CREG_SIZE		0x00100000
-
-#define IXP2000_PCI_CSR_PHYS_BASE	0xdf000000
-#define	IXP2000_PCI_CSR_VIRT_BASE	0xfec00000
-#define	IXP2000_PCI_CSR_SIZE		0x00100000
-
-#define IXP2000_MSF_PHYS_BASE		0xc8000000
-#define IXP2000_MSF_VIRT_BASE		0xfeb00000
-#define IXP2000_MSF_SIZE		0x00100000
-
-#define IXP2000_SCRATCH_RING_PHYS_BASE	0xcb400000
-#define IXP2000_SCRATCH_RING_VIRT_BASE	0xfea00000
-#define IXP2000_SCRATCH_RING_SIZE	0x00100000
-
-#define IXP2000_SRAM0_PHYS_BASE		0x80000000
-#define IXP2000_SRAM0_VIRT_BASE		0xfe900000
-#define IXP2000_SRAM0_SIZE		0x00100000
-
-#define IXP2000_PCI_IO_PHYS_BASE	0xd8000000
-#define	IXP2000_PCI_IO_VIRT_BASE	0xfd000000
-#define IXP2000_PCI_IO_SIZE     	0x01000000
-
-#define IXP2000_PCI_CFG0_PHYS_BASE	0xda000000
-#define IXP2000_PCI_CFG0_VIRT_BASE	0xfc000000
-#define IXP2000_PCI_CFG0_SIZE   	0x01000000
-
-#define IXP2000_PCI_CFG1_PHYS_BASE	0xdb000000
-#define IXP2000_PCI_CFG1_VIRT_BASE	0xfb000000
-#define IXP2000_PCI_CFG1_SIZE		0x01000000
-
-/* 
- * Timers
- */
-#define	IXP2000_TIMER_REG(x)		((volatile unsigned long*)(IXP2000_TIMER_VIRT_BASE | (x)))
-/* Timer control */
-#define	IXP2000_T1_CTL			IXP2000_TIMER_REG(0x00)
-#define	IXP2000_T2_CTL			IXP2000_TIMER_REG(0x04)
-#define	IXP2000_T3_CTL			IXP2000_TIMER_REG(0x08)
-#define	IXP2000_T4_CTL			IXP2000_TIMER_REG(0x0c)
-/* Store initial value */
-#define	IXP2000_T1_CLD			IXP2000_TIMER_REG(0x10)
-#define	IXP2000_T2_CLD			IXP2000_TIMER_REG(0x14)
-#define	IXP2000_T3_CLD			IXP2000_TIMER_REG(0x18)
-#define	IXP2000_T4_CLD			IXP2000_TIMER_REG(0x1c)
-/* Read current value */
-#define	IXP2000_T1_CSR			IXP2000_TIMER_REG(0x20)
-#define	IXP2000_T2_CSR			IXP2000_TIMER_REG(0x24)
-#define	IXP2000_T3_CSR			IXP2000_TIMER_REG(0x28)
-#define	IXP2000_T4_CSR			IXP2000_TIMER_REG(0x2c)
-/* Clear associated timer interrupt */
-#define	IXP2000_T1_CLR			IXP2000_TIMER_REG(0x30)
-#define	IXP2000_T2_CLR			IXP2000_TIMER_REG(0x34)
-#define	IXP2000_T3_CLR			IXP2000_TIMER_REG(0x38)
-#define	IXP2000_T4_CLR			IXP2000_TIMER_REG(0x3c)
-/* Timer watchdog enable for T4 */
-#define	IXP2000_TWDE			IXP2000_TIMER_REG(0x40)
-
-#define	WDT_ENABLE			0x00000001
-#define	TIMER_DIVIDER_256		0x00000008
-#define	TIMER_ENABLE			0x00000080
-#define	IRQ_MASK_TIMER1         	(1 << 4)
-
-/*
- * Interrupt controller registers
- */
-#define IXP2000_INTCTL_REG(x)		(volatile unsigned long*)(IXP2000_INTCTL_VIRT_BASE | (x))
-#define IXP2000_IRQ_STATUS		IXP2000_INTCTL_REG(0x08)
-#define IXP2000_IRQ_ENABLE		IXP2000_INTCTL_REG(0x10)
-#define IXP2000_IRQ_ENABLE_SET		IXP2000_INTCTL_REG(0x10)
-#define IXP2000_IRQ_ENABLE_CLR		IXP2000_INTCTL_REG(0x18)
-#define IXP2000_FIQ_ENABLE_CLR		IXP2000_INTCTL_REG(0x14)
-#define IXP2000_IRQ_ERR_STATUS		IXP2000_INTCTL_REG(0x24)
-#define IXP2000_IRQ_ERR_ENABLE_SET	IXP2000_INTCTL_REG(0x2c)
-#define IXP2000_FIQ_ERR_ENABLE_CLR	IXP2000_INTCTL_REG(0x30)
-#define IXP2000_IRQ_ERR_ENABLE_CLR	IXP2000_INTCTL_REG(0x34)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_0	IXP2000_INTCTL_REG(0x60)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_1	IXP2000_INTCTL_REG(0x64)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_2	IXP2000_INTCTL_REG(0x68)
-#define IXP2000_IRQ_THD_RAW_STATUS_A_3	IXP2000_INTCTL_REG(0x6c)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_0	IXP2000_INTCTL_REG(0x80)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_1	IXP2000_INTCTL_REG(0x84)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_2	IXP2000_INTCTL_REG(0x88)
-#define IXP2000_IRQ_THD_RAW_STATUS_B_3	IXP2000_INTCTL_REG(0x8c)
-#define IXP2000_IRQ_THD_STATUS_A_0	IXP2000_INTCTL_REG(0xe0)
-#define IXP2000_IRQ_THD_STATUS_A_1	IXP2000_INTCTL_REG(0xe4)
-#define IXP2000_IRQ_THD_STATUS_A_2	IXP2000_INTCTL_REG(0xe8)
-#define IXP2000_IRQ_THD_STATUS_A_3	IXP2000_INTCTL_REG(0xec)
-#define IXP2000_IRQ_THD_STATUS_B_0	IXP2000_INTCTL_REG(0x100)
-#define IXP2000_IRQ_THD_STATUS_B_1	IXP2000_INTCTL_REG(0x104)
-#define IXP2000_IRQ_THD_STATUS_B_2	IXP2000_INTCTL_REG(0x108)
-#define IXP2000_IRQ_THD_STATUS_B_3	IXP2000_INTCTL_REG(0x10c)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_0	IXP2000_INTCTL_REG(0x160)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_1	IXP2000_INTCTL_REG(0x164)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_2	IXP2000_INTCTL_REG(0x168)
-#define IXP2000_IRQ_THD_ENABLE_SET_A_3	IXP2000_INTCTL_REG(0x16c)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_0	IXP2000_INTCTL_REG(0x180)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_1	IXP2000_INTCTL_REG(0x184)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_2	IXP2000_INTCTL_REG(0x188)
-#define IXP2000_IRQ_THD_ENABLE_SET_B_3	IXP2000_INTCTL_REG(0x18c)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_0	IXP2000_INTCTL_REG(0x1e0)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_1	IXP2000_INTCTL_REG(0x1e4)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_2	IXP2000_INTCTL_REG(0x1e8)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_A_3	IXP2000_INTCTL_REG(0x1ec)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_0	IXP2000_INTCTL_REG(0x200)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_1	IXP2000_INTCTL_REG(0x204)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_2	IXP2000_INTCTL_REG(0x208)
-#define IXP2000_IRQ_THD_ENABLE_CLEAR_B_3	IXP2000_INTCTL_REG(0x20c)
-
-/*
- * Mask of valid IRQs in the 32-bit IRQ register. We use
- * this to mark certain IRQs as being invalid.
- */
-#define	IXP2000_VALID_IRQ_MASK	0x0f0fffff
-
-/*
- * PCI config register access from core
- */
-#define IXP2000_PCI_CREG(x)		(volatile unsigned long*)(IXP2000_PCI_CREG_VIRT_BASE | (x))
-#define IXP2000_PCI_CMDSTAT 		IXP2000_PCI_CREG(0x04)
-#define IXP2000_PCI_CSR_BAR		IXP2000_PCI_CREG(0x10)
-#define IXP2000_PCI_SRAM_BAR		IXP2000_PCI_CREG(0x14)
-#define IXP2000_PCI_SDRAM_BAR		IXP2000_PCI_CREG(0x18)
-
-/*
- * PCI CSRs
- */
-#define IXP2000_PCI_CSR(x)		(volatile unsigned long*)(IXP2000_PCI_CSR_VIRT_BASE | (x))
-
-/*
- * PCI outbound interrupts
- */
-#define IXP2000_PCI_OUT_INT_STATUS	IXP2000_PCI_CSR(0x30)
-#define IXP2000_PCI_OUT_INT_MASK	IXP2000_PCI_CSR(0x34)
-/*
- * PCI communications
- */
-#define IXP2000_PCI_MAILBOX0		IXP2000_PCI_CSR(0x50)
-#define IXP2000_PCI_MAILBOX1		IXP2000_PCI_CSR(0x54)
-#define IXP2000_PCI_MAILBOX2		IXP2000_PCI_CSR(0x58)
-#define IXP2000_PCI_MAILBOX3		IXP2000_PCI_CSR(0x5C)
-#define IXP2000_XSCALE_DOORBELL		IXP2000_PCI_CSR(0x60)
-#define IXP2000_XSCALE_DOORBELL_SETUP	IXP2000_PCI_CSR(0x64)
-#define IXP2000_PCI_DOORBELL		IXP2000_PCI_CSR(0x70)
-#define IXP2000_PCI_DOORBELL_SETUP	IXP2000_PCI_CSR(0x74)
-
-/*
- * DMA engines
- */
-#define IXP2000_PCI_CH1_BYTE_CNT	IXP2000_PCI_CSR(0x80)
-#define IXP2000_PCI_CH1_ADDR		IXP2000_PCI_CSR(0x84)
-#define IXP2000_PCI_CH1_DRAM_ADDR	IXP2000_PCI_CSR(0x88)
-#define IXP2000_PCI_CH1_DESC_PTR	IXP2000_PCI_CSR(0x8C)
-#define IXP2000_PCI_CH1_CNTRL		IXP2000_PCI_CSR(0x90)
-#define IXP2000_PCI_CH1_ME_PARAM	IXP2000_PCI_CSR(0x94)
-#define IXP2000_PCI_CH2_BYTE_CNT	IXP2000_PCI_CSR(0xA0)
-#define IXP2000_PCI_CH2_ADDR		IXP2000_PCI_CSR(0xA4)
-#define IXP2000_PCI_CH2_DRAM_ADDR	IXP2000_PCI_CSR(0xA8)
-#define IXP2000_PCI_CH2_DESC_PTR	IXP2000_PCI_CSR(0xAC)
-#define IXP2000_PCI_CH2_CNTRL		IXP2000_PCI_CSR(0xB0)
-#define IXP2000_PCI_CH2_ME_PARAM	IXP2000_PCI_CSR(0xB4)
-#define IXP2000_PCI_CH3_BYTE_CNT	IXP2000_PCI_CSR(0xC0)
-#define IXP2000_PCI_CH3_ADDR		IXP2000_PCI_CSR(0xC4)
-#define IXP2000_PCI_CH3_DRAM_ADDR	IXP2000_PCI_CSR(0xC8)
-#define IXP2000_PCI_CH3_DESC_PTR	IXP2000_PCI_CSR(0xCC)
-#define IXP2000_PCI_CH3_CNTRL		IXP2000_PCI_CSR(0xD0)
-#define IXP2000_PCI_CH3_ME_PARAM	IXP2000_PCI_CSR(0xD4)
-#define IXP2000_DMA_INF_MODE		IXP2000_PCI_CSR(0xE0)
-/*
- * Size masks for BARs
- */
-#define IXP2000_PCI_SRAM_BASE_ADDR_MASK	IXP2000_PCI_CSR(0xFC)
-#define IXP2000_PCI_DRAM_BASE_ADDR_MASK	IXP2000_PCI_CSR(0x100)
-/*
- * Control and uEngine related
- */
-#define IXP2000_PCI_CONTROL		IXP2000_PCI_CSR(0x13C)
-#define IXP2000_PCI_ADDR_EXT		IXP2000_PCI_CSR(0x140)
-#define IXP2000_PCI_ME_PUSH_STATUS	IXP2000_PCI_CSR(0x148)
-#define IXP2000_PCI_ME_PUSH_EN		IXP2000_PCI_CSR(0x14C)
-#define IXP2000_PCI_ERR_STATUS		IXP2000_PCI_CSR(0x150)
-#define IXP2000_PCI_ERR_ENABLE		IXP2000_PCI_CSR(0x154)
-/*
- * Inbound PCI interrupt control
- */
-#define IXP2000_PCI_XSCALE_INT_STATUS	IXP2000_PCI_CSR(0x158)
-#define IXP2000_PCI_XSCALE_INT_ENABLE	IXP2000_PCI_CSR(0x15C)
-
-#define IXP2000_PCICNTL_PNR		(1<<17)	/* PCI not Reset bit of PCI_CONTROL */
-#define IXP2000_PCICNTL_PCF		(1<<28)	/* PCI Central function bit */
-#define IXP2000_XSCALE_INT		(1<<1)	/* Interrupt from XScale to PCI */
-
-/* These are from the IRQ register in the PCI ISR register */
-#define PCI_CONTROL_BE_DEO		(1 << 22)	/* Big Endian Data Enable Out */
-#define PCI_CONTROL_BE_DEI		(1 << 21)	/* Big Endian Data Enable In  */
-#define PCI_CONTROL_BE_BEO		(1 << 20)	/* Big Endian Byte Enable Out */
-#define PCI_CONTROL_BE_BEI		(1 << 19)	/* Big Endian Byte Enable In  */
-#define PCI_CONTROL_IEE			(1 << 17)	/* I/O cycle Endian swap Enable */
-
-#define IXP2000_PCI_RST_REL		(1 << 2)
-#define CFG_RST_DIR			(*IXP2000_PCI_CONTROL & IXP2000_PCICNTL_PCF)
-#define CFG_PCI_BOOT_HOST		(1 << 2)
-#define CFG_BOOT_PROM			(1 << 1)
-
-/*
- * SlowPort CSRs
- *
- * The slowport is used to access things like flash, SONET framer control
- * ports, slave microprocessors, CPLDs, and others of chip memory mapped
- * peripherals.
- */
-#define	SLOWPORT_CSR(x)		(volatile unsigned long*)(IXP2000_SLOWPORT_CSR_VIRT_BASE | (x))
-
-#define	IXP2000_SLOWPORT_CCR		SLOWPORT_CSR(0x00)
-#define	IXP2000_SLOWPORT_WTC1		SLOWPORT_CSR(0x04)
-#define	IXP2000_SLOWPORT_WTC2		SLOWPORT_CSR(0x08)
-#define	IXP2000_SLOWPORT_RTC1		SLOWPORT_CSR(0x0c)
-#define	IXP2000_SLOWPORT_RTC2		SLOWPORT_CSR(0x10)
-#define	IXP2000_SLOWPORT_FSR		SLOWPORT_CSR(0x14)
-#define	IXP2000_SLOWPORT_PCR		SLOWPORT_CSR(0x18)
-#define	IXP2000_SLOWPORT_ADC		SLOWPORT_CSR(0x1C)
-#define	IXP2000_SLOWPORT_FAC		SLOWPORT_CSR(0x20)
-#define	IXP2000_SLOWPORT_FRM		SLOWPORT_CSR(0x24)
-#define	IXP2000_SLOWPORT_FIN		SLOWPORT_CSR(0x28)
-
-/*
- * CCR values.  
- * The CCR configures the clock division for the slowport interface.
- */
-#define	SLOWPORT_CCR_DIV_1		0x00
-#define	SLOWPORT_CCR_DIV_2		0x01
-#define	SLOWPORT_CCR_DIV_4		0x02
-#define	SLOWPORT_CCR_DIV_6		0x03
-#define	SLOWPORT_CCR_DIV_8		0x04
-#define	SLOWPORT_CCR_DIV_10		0x05
-#define	SLOWPORT_CCR_DIV_12		0x06
-#define	SLOWPORT_CCR_DIV_14		0x07
-#define	SLOWPORT_CCR_DIV_16		0x08
-#define	SLOWPORT_CCR_DIV_18		0x09
-#define	SLOWPORT_CCR_DIV_20		0x0a
-#define	SLOWPORT_CCR_DIV_22		0x0b
-#define	SLOWPORT_CCR_DIV_24		0x0c
-#define	SLOWPORT_CCR_DIV_26		0x0d
-#define	SLOWPORT_CCR_DIV_28		0x0e
-#define	SLOWPORT_CCR_DIV_30		0x0f
-
-/*
- * PCR values.  PCR configure the mode of the interface.
- */
-#define	SLOWPORT_MODE_FLASH		0x00
-#define	SLOWPORT_MODE_LUCENT		0x01
-#define	SLOWPORT_MODE_PMC_SIERRA	0x02
-#define	SLOWPORT_MODE_INTEL_UP		0x03
-#define	SLOWPORT_MODE_MOTOROLA_UP	0x04
-
-/*
- * ADC values.  Defines data and address bus widths.
- */
-#define	SLOWPORT_ADDR_WIDTH_8		0x00
-#define	SLOWPORT_ADDR_WIDTH_16		0x01
-#define	SLOWPORT_ADDR_WIDTH_24		0x02
-#define	SLOWPORT_ADDR_WIDTH_32		0x03
-#define	SLOWPORT_DATA_WIDTH_8		0x00
-#define	SLOWPORT_DATA_WIDTH_16		0x10
-#define	SLOWPORT_DATA_WIDTH_24		0x20
-#define	SLOWPORT_DATA_WIDTH_32		0x30
-
-/*
- * Masks and shifts for various fields in the WTC and RTC registers.
- */
-#define	SLOWPORT_WRTC_MASK_HD		0x0003
-#define	SLOWPORT_WRTC_MASK_PW		0x003c
-#define	SLOWPORT_WRTC_MASK_SU		0x03c0
-
-#define	SLOWPORT_WRTC_SHIFT_HD		0x00
-#define	SLOWPORT_WRTC_SHIFT_SU		0x02
-#define	SLOWPORT_WRTC_SHFIT_PW		0x06
-
-
-/*
- * GPIO registers & GPIO interface.
- */
-#define IXP2000_GPIO_REG(x)		((volatile unsigned long*)(IXP2000_GPIO_VIRT_BASE+(x)))
-#define IXP2000_GPIO_PLR		IXP2000_GPIO_REG(0x00)
-#define IXP2000_GPIO_PDPR		IXP2000_GPIO_REG(0x04)
-#define IXP2000_GPIO_PDSR		IXP2000_GPIO_REG(0x08)
-#define IXP2000_GPIO_PDCR		IXP2000_GPIO_REG(0x0c)
-#define IXP2000_GPIO_POPR		IXP2000_GPIO_REG(0x10)
-#define IXP2000_GPIO_POSR		IXP2000_GPIO_REG(0x14)
-#define IXP2000_GPIO_POCR		IXP2000_GPIO_REG(0x18)
-#define IXP2000_GPIO_REDR		IXP2000_GPIO_REG(0x1c)
-#define IXP2000_GPIO_FEDR		IXP2000_GPIO_REG(0x20)
-#define IXP2000_GPIO_EDSR		IXP2000_GPIO_REG(0x24)
-#define IXP2000_GPIO_LSHR		IXP2000_GPIO_REG(0x28)
-#define IXP2000_GPIO_LSLR		IXP2000_GPIO_REG(0x2c)
-#define IXP2000_GPIO_LDSR		IXP2000_GPIO_REG(0x30)
-#define IXP2000_GPIO_INER		IXP2000_GPIO_REG(0x34)
-#define IXP2000_GPIO_INSR		IXP2000_GPIO_REG(0x38)
-#define IXP2000_GPIO_INCR		IXP2000_GPIO_REG(0x3c)
-#define IXP2000_GPIO_INST		IXP2000_GPIO_REG(0x40)
-
-/*
- * "Global" registers...whatever that's supposed to mean.
- */
-#define GLOBAL_REG_BASE			(IXP2000_GLOBAL_REG_VIRT_BASE + 0x0a00)
-#define GLOBAL_REG(x)			(volatile unsigned long*)(GLOBAL_REG_BASE | (x))
-
-#define IXP2000_MAJ_PROD_TYPE_MASK	0x001F0000
-#define IXP2000_MAJ_PROD_TYPE_IXP2000	0x00000000
-#define IXP2000_MIN_PROD_TYPE_MASK 	0x0000FF00
-#define IXP2000_MIN_PROD_TYPE_IXP2400	0x00000200
-#define IXP2000_MIN_PROD_TYPE_IXP2850	0x00000100
-#define IXP2000_MIN_PROD_TYPE_IXP2800	0x00000000
-#define IXP2000_MAJ_REV_MASK	      	0x000000F0
-#define IXP2000_MIN_REV_MASK	      	0x0000000F
-#define IXP2000_PROD_ID_MASK		0xFFFFFFFF
-
-#define IXP2000_PRODUCT_ID		GLOBAL_REG(0x00)
-#define IXP2000_MISC_CONTROL		GLOBAL_REG(0x04)
-#define IXP2000_MSF_CLK_CNTRL  		GLOBAL_REG(0x08)
-#define IXP2000_RESET0      		GLOBAL_REG(0x0c)
-#define IXP2000_RESET1      		GLOBAL_REG(0x10)
-#define IXP2000_CCR            		GLOBAL_REG(0x14)
-#define	IXP2000_STRAP_OPTIONS  		GLOBAL_REG(0x18)
-
-#define	RSTALL				(1 << 16)
-#define	WDT_RESET_ENABLE		0x01000000
-
-
-/*
- * MSF registers.  The IXP2400 and IXP2800 have somewhat different MSF
- * units, but the registers that differ between the two don't overlap,
- * so we can have one register list for both.
- */
-#define IXP2000_MSF_REG(x)			((volatile unsigned long*)(IXP2000_MSF_VIRT_BASE + (x)))
-#define IXP2000_MSF_RX_CONTROL			IXP2000_MSF_REG(0x0000)
-#define IXP2000_MSF_TX_CONTROL			IXP2000_MSF_REG(0x0004)
-#define IXP2000_MSF_INTERRUPT_STATUS		IXP2000_MSF_REG(0x0008)
-#define IXP2000_MSF_INTERRUPT_ENABLE		IXP2000_MSF_REG(0x000c)
-#define IXP2000_MSF_CSIX_TYPE_MAP		IXP2000_MSF_REG(0x0010)
-#define IXP2000_MSF_FC_EGRESS_STATUS		IXP2000_MSF_REG(0x0014)
-#define IXP2000_MSF_FC_INGRESS_STATUS		IXP2000_MSF_REG(0x0018)
-#define IXP2000_MSF_HWM_CONTROL			IXP2000_MSF_REG(0x0024)
-#define IXP2000_MSF_FC_STATUS_OVERRIDE		IXP2000_MSF_REG(0x0028)
-#define IXP2000_MSF_CLOCK_CONTROL		IXP2000_MSF_REG(0x002c)
-#define IXP2000_MSF_RX_PORT_MAP			IXP2000_MSF_REG(0x0040)
-#define IXP2000_MSF_RBUF_ELEMENT_DONE		IXP2000_MSF_REG(0x0044)
-#define IXP2000_MSF_RX_MPHY_POLL_LIMIT		IXP2000_MSF_REG(0x0048)
-#define IXP2000_MSF_RX_CALENDAR_LENGTH		IXP2000_MSF_REG(0x0048)
-#define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_0	IXP2000_MSF_REG(0x0050)
-#define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_1	IXP2000_MSF_REG(0x0054)
-#define IXP2000_MSF_RX_THREAD_FREELIST_TIMEOUT_2	IXP2000_MSF_REG(0x0058)
-#define IXP2000_MSF_TX_SEQUENCE_0		IXP2000_MSF_REG(0x0060)
-#define IXP2000_MSF_TX_SEQUENCE_1		IXP2000_MSF_REG(0x0064)
-#define IXP2000_MSF_TX_SEQUENCE_2		IXP2000_MSF_REG(0x0068)
-#define IXP2000_MSF_TX_MPHY_POLL_LIMIT		IXP2000_MSF_REG(0x0070)
-#define IXP2000_MSF_TX_CALENDAR_LENGTH		IXP2000_MSF_REG(0x0070)
-#define IXP2000_MSF_RX_UP_CONTROL_0		IXP2000_MSF_REG(0x0080)
-#define IXP2000_MSF_RX_UP_CONTROL_1		IXP2000_MSF_REG(0x0084)
-#define IXP2000_MSF_RX_UP_CONTROL_2		IXP2000_MSF_REG(0x0088)
-#define IXP2000_MSF_RX_UP_CONTROL_3		IXP2000_MSF_REG(0x008c)
-#define IXP2000_MSF_TX_UP_CONTROL_0		IXP2000_MSF_REG(0x0090)
-#define IXP2000_MSF_TX_UP_CONTROL_1		IXP2000_MSF_REG(0x0094)
-#define IXP2000_MSF_TX_UP_CONTROL_2		IXP2000_MSF_REG(0x0098)
-#define IXP2000_MSF_TX_UP_CONTROL_3		IXP2000_MSF_REG(0x009c)
-#define IXP2000_MSF_TRAIN_DATA			IXP2000_MSF_REG(0x00a0)
-#define IXP2000_MSF_TRAIN_CALENDAR		IXP2000_MSF_REG(0x00a4)
-#define IXP2000_MSF_TRAIN_FLOW_CONTROL		IXP2000_MSF_REG(0x00a8)
-#define IXP2000_MSF_TX_CALENDAR_0		IXP2000_MSF_REG(0x1000)
-#define IXP2000_MSF_RX_PORT_CALENDAR_STATUS	IXP2000_MSF_REG(0x1400)
-
-
-#endif				/* _IXP2000_H_ */
diff --git a/arch/arm/mach-ixp2000/include/mach/memory.h b/arch/arm/mach-ixp2000/include/mach/memory.h
deleted file mode 100644
index 5f0c4fd..0000000
--- a/arch/arm/mach-ixp2000/include/mach/memory.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/memory.h
- *
- * Copyright (c) 2002 Intel Corp.
- * Copyright (c) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x00000000)
-
-#include <mach/ixp2000-regs.h>
-
-#define IXP2000_PCI_SDRAM_OFFSET	(*IXP2000_PCI_SDRAM_BAR & 0xfffffff0)
-
-#define __phys_to_bus(x)	((x) + (IXP2000_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-#define __bus_to_phys(x)	((x) - (IXP2000_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-
-#define __virt_to_bus(v)	__phys_to_bus(__virt_to_phys(v))
-#define __bus_to_virt(b)	__phys_to_virt(__bus_to_phys(b))
-#define __pfn_to_bus(p)		__phys_to_bus(__pfn_to_phys(p))
-#define __bus_to_pfn(b)		__phys_to_pfn(__bus_to_phys(b))
-
-#endif
-
diff --git a/arch/arm/mach-ixp2000/include/mach/platform.h b/arch/arm/mach-ixp2000/include/mach/platform.h
deleted file mode 100644
index bb0f8dc..0000000
--- a/arch/arm/mach-ixp2000/include/mach/platform.h
+++ /dev/null
@@ -1,153 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/platform.h
- *
- * Various bits of code used by platform-level code.
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2004 (c) MontaVista Software, Inc. 
- * 
- * This file is licensed under  the terms of the GNU General Public 
- * License version 2. This program is licensed "as is" without any 
- * warranty of any kind, whether express or implied.
- */
-
-
-#ifndef __ASSEMBLY__
-
-static inline unsigned long ixp2000_reg_read(volatile void *reg)
-{
-	return *((volatile unsigned long *)reg);
-}
-
-static inline void ixp2000_reg_write(volatile void *reg, unsigned long val)
-{
-	*((volatile unsigned long *)reg) = val;
-}
-
-/*
- * On the IXP2400, we can't use XCB=000 due to chip bugs.  We use
- * XCB=101 instead, but that makes all I/O accesses bufferable.  This
- * is not a problem in general, but we do have to be slightly more
- * careful because I/O writes are no longer automatically flushed out
- * of the write buffer.
- *
- * In cases where we want to make sure that a write has been flushed
- * out of the write buffer before we proceed, for example when masking
- * a device interrupt before re-enabling IRQs in CPSR, we can use this
- * function, ixp2000_reg_wrb, which performs a write, a readback, and
- * issues a dummy instruction dependent on the value of the readback
- * (mov rX, rX) to make sure that the readback has completed before we
- * continue.
- */
-static inline void ixp2000_reg_wrb(volatile void *reg, unsigned long val)
-{
-	unsigned long dummy;
-
-	*((volatile unsigned long *)reg) = val;
-
-	dummy = *((volatile unsigned long *)reg);
-	__asm__ __volatile__("mov %0, %0" : "+r" (dummy));
-}
-
-/*
- * Boards may multiplex different devices on the 2nd channel of 
- * the slowport interface that each need different configuration 
- * settings.  For example, the IXDP2400 uses channel 2 on the interface 
- * to access the CPLD, the switch fabric card, and the media card.  Each
- * one needs a different mode so drivers must save/restore the mode 
- * before and after each operation.  
- *
- * acquire_slowport(&your_config);
- * ...
- * do slowport operations
- * ...
- * release_slowport();
- *
- * Note that while you have the slowport, you are holding a spinlock,
- * so your code should be written as if you explicitly acquired a lock.
- *
- * The configuration only affects device 2 on the slowport, so the
- * MTD map driver does not acquire/release the slowport.  
- */
-struct slowport_cfg {
-	unsigned long CCR;	/* Clock divide */
-	unsigned long WTC;	/* Write Timing Control */
-	unsigned long RTC;	/* Read Timing Control */
-	unsigned long PCR;	/* Protocol Control Register */
-	unsigned long ADC;	/* Address/Data Width Control */
-};
-
-
-void ixp2000_acquire_slowport(struct slowport_cfg *, struct slowport_cfg *);
-void ixp2000_release_slowport(struct slowport_cfg *);
-
-/*
- * IXP2400 A0/A1 and  IXP2800 A0/A1/A2 have broken slowport that requires
- * tweaking of addresses in the MTD driver.
- */
-static inline unsigned ixp2000_has_broken_slowport(void)
-{
-	unsigned long id = *IXP2000_PRODUCT_ID;
-	unsigned long id_prod = id & (IXP2000_MAJ_PROD_TYPE_MASK |
-				      IXP2000_MIN_PROD_TYPE_MASK);
-	return (((id_prod ==
-		  /* fixed in IXP2400-B0 */
-		  (IXP2000_MAJ_PROD_TYPE_IXP2000 |
-		   IXP2000_MIN_PROD_TYPE_IXP2400)) &&
-		 ((id & IXP2000_MAJ_REV_MASK) == 0)) ||
-		((id_prod ==
-		  /* fixed in IXP2800-B0 */
-		  (IXP2000_MAJ_PROD_TYPE_IXP2000 |
-		   IXP2000_MIN_PROD_TYPE_IXP2800)) &&
-		 ((id & IXP2000_MAJ_REV_MASK) == 0)) ||
-		((id_prod ==
-		  /* fixed in IXP2850-B0 */
-		  (IXP2000_MAJ_PROD_TYPE_IXP2000 |
-		   IXP2000_MIN_PROD_TYPE_IXP2850)) &&
-		 ((id & IXP2000_MAJ_REV_MASK) == 0)));
-}
-
-static inline unsigned int ixp2000_has_flash(void)
-{
-	return ((*IXP2000_STRAP_OPTIONS) & (CFG_BOOT_PROM));
-}
-
-static inline unsigned int ixp2000_is_pcimaster(void)
-{
-	return ((*IXP2000_STRAP_OPTIONS) & (CFG_PCI_BOOT_HOST));
-}
-
-void ixp2000_map_io(void);
-void ixp2000_uart_init(void);
-void ixp2000_init_irq(void);
-void ixp2000_init_time(unsigned long);
-void ixp2000_restart(char, const char *);
-unsigned long ixp2000_gettimeoffset(void);
-
-struct pci_sys_data;
-
-u32 *ixp2000_pci_config_addr(unsigned int bus, unsigned int devfn, int where);
-void ixp2000_pci_preinit(void);
-int ixp2000_pci_setup(int, struct pci_sys_data*);
-struct pci_bus* ixp2000_pci_scan_bus(int, struct pci_sys_data*);
-int ixp2000_pci_read_config(struct pci_bus*, unsigned int, int, int, u32 *);
-int ixp2000_pci_write_config(struct pci_bus*, unsigned int, int, int, u32);
-
-/*
- * Several of the IXP2000 systems have banked flash so we need to extend the
- * flash_platform_data structure with some private pointers
- */
-struct ixp2000_flash_data {
-	struct flash_platform_data *platform_data;
-	int nr_banks;
-	unsigned long (*bank_setup)(unsigned long);
-};
-
-struct ixp2000_i2c_pins {
-	unsigned long sda_pin;
-	unsigned long scl_pin;
-};
-
-
-#endif /*  !__ASSEMBLY__ */
diff --git a/arch/arm/mach-ixp2000/include/mach/timex.h b/arch/arm/mach-ixp2000/include/mach/timex.h
deleted file mode 100644
index 835e659..0000000
--- a/arch/arm/mach-ixp2000/include/mach/timex.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/timex.h
- *
- * IXP2000 architecture timex specifications
- */
-
-
-/*
- * Default clock is 50MHz APB, but platform code can override this
- */
-#define CLOCK_TICK_RATE	50000000
-
-
diff --git a/arch/arm/mach-ixp2000/include/mach/uncompress.h b/arch/arm/mach-ixp2000/include/mach/uncompress.h
deleted file mode 100644
index ce36308..0000000
--- a/arch/arm/mach-ixp2000/include/mach/uncompress.h
+++ /dev/null
@@ -1,47 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/uncompress.h
- *
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2002 Intel Corp.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- */
-
-#include <linux/serial_reg.h>
-
-#define UART_BASE	0xc0030000
-
-#define PHYS(x)          ((volatile unsigned long *)(UART_BASE + x))
-
-#define UARTDR          PHYS(0x00)      /* Transmit reg dlab=0 */
-#define UARTDLL         PHYS(0x00)      /* Divisor Latch reg dlab=1*/
-#define UARTDLM         PHYS(0x04)      /* Divisor Latch reg dlab=1*/
-#define UARTIER         PHYS(0x04)      /* Interrupt enable reg */
-#define UARTFCR         PHYS(0x08)      /* FIFO control reg dlab =0*/
-#define UARTLCR         PHYS(0x0c)      /* Control reg */
-#define UARTSR          PHYS(0x14)      /* Status reg */
-
-
-static inline void putc(int c)
-{
-	int j = 0x1000;
-
-	while (--j && !(*UARTSR & UART_LSR_THRE))
-		barrier();
-
-	*UARTDR = c;
-}
-
-static inline void flush(void)
-{
-}
-
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
diff --git a/arch/arm/mach-ixp2000/ixdp2400.c b/arch/arm/mach-ixp2000/ixdp2400.c
deleted file mode 100644
index 915ad49..0000000
--- a/arch/arm/mach-ixp2000/ixdp2400.c
+++ /dev/null
@@ -1,180 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/ixdp2400.c
- *
- * IXDP2400 platform support
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/arch.h>
-
-/*************************************************************************
- * IXDP2400 timer tick
- *************************************************************************/
-static void __init ixdp2400_timer_init(void)
-{
-	int numerator, denominator;
-	int denom_array[] = {2, 4, 8, 16, 1, 2, 4, 8};
-
-	numerator = (*(IXDP2400_CPLD_SYS_CLK_M) & 0xFF) *2;
-	denominator = denom_array[(*(IXDP2400_CPLD_SYS_CLK_N) & 0x7)];
-
-	ixp2000_init_time(((3125000 * numerator) / (denominator)) / 2);
-}
-
-static struct sys_timer ixdp2400_timer = {
-	.init		= ixdp2400_timer_init,
-	.offset		= ixp2000_gettimeoffset,
-};
-
-/*************************************************************************
- * IXDP2400 PCI
- *************************************************************************/
-void __init ixdp2400_pci_preinit(void)
-{
-	ixp2000_reg_write(IXP2000_PCI_ADDR_EXT, 0x00100000);
-	ixp2000_pci_preinit();
-	pcibios_setup("firmware");
-}
-
-int ixdp2400_pci_setup(int nr, struct pci_sys_data *sys)
-{
-	sys->mem_offset = 0xe0000000;
-
-	ixp2000_pci_setup(nr, sys);
-
-	return 1;
-}
-
-static int __init ixdp2400_pci_map_irq(const struct pci_dev *dev, u8 slot,
-	u8 pin)
-{
-	if (ixdp2x00_master_npu()) {
-
-		/*
-		 * Root bus devices.  Slave NPU is only one with interrupt.
-		 * Everything else, we just return -1 b/c nothing else
-		 * on the root bus has interrupts.
-		 */
-		if(!dev->bus->self) {
-			if(dev->devfn == IXDP2X00_SLAVE_NPU_DEVFN )
-				return IRQ_IXDP2400_INGRESS_NPU;
-
-			return -1;
-		}
-
-		/*
-		 * Bridge behind the PMC slot.
-		 * NOTE: Only INTA from the PMC slot is routed. VERY BAD.
-		 */
-		if(dev->bus->self->devfn == IXDP2X00_PMC_DEVFN &&
-			dev->bus->parent->self->devfn == IXDP2X00_P2P_DEVFN &&
-			!dev->bus->parent->self->bus->parent)
-				  return IRQ_IXDP2400_PMC;
-
-		/*
-		 * Device behind the first bridge
-		 */
-		if(dev->bus->self->devfn == IXDP2X00_P2P_DEVFN) {
-			switch(dev->devfn) {
-				case IXDP2400_MASTER_ENET_DEVFN:	
-					return IRQ_IXDP2400_ENET;	
-			
-				case IXDP2400_MEDIA_DEVFN:
-					return IRQ_IXDP2400_MEDIA_PCI;
-
-				case IXDP2400_SWITCH_FABRIC_DEVFN:
-					return IRQ_IXDP2400_SF_PCI;
-
-				case IXDP2X00_PMC_DEVFN:
-					return IRQ_IXDP2400_PMC;
-			}
-		}
-
-		return -1;
-	} else return IRQ_IXP2000_PCIB; /* Slave NIC interrupt */
-}
-
-
-static void ixdp2400_pci_postinit(void)
-{
-	struct pci_dev *dev;
-
-	if (ixdp2x00_master_npu()) {
-		dev = pci_get_bus_and_slot(1, IXDP2400_SLAVE_ENET_DEVFN);
-		pci_stop_and_remove_bus_device(dev);
-		pci_dev_put(dev);
-	} else {
-		dev = pci_get_bus_and_slot(1, IXDP2400_MASTER_ENET_DEVFN);
-		pci_stop_and_remove_bus_device(dev);
-		pci_dev_put(dev);
-
-		ixdp2x00_slave_pci_postinit();
-	}
-}
-
-static struct hw_pci ixdp2400_pci __initdata = {
-	.nr_controllers	= 1,
-	.setup		= ixdp2400_pci_setup,
-	.preinit	= ixdp2400_pci_preinit,
-	.postinit	= ixdp2400_pci_postinit,
-	.scan		= ixp2000_pci_scan_bus,
-	.map_irq	= ixdp2400_pci_map_irq,
-};
-
-int __init ixdp2400_pci_init(void)
-{
-	if (machine_is_ixdp2400())
-		pci_common_init(&ixdp2400_pci);
-
-	return 0;
-}
-
-subsys_initcall(ixdp2400_pci_init);
-
-void __init ixdp2400_init_irq(void)
-{
-	ixdp2x00_init_irq(IXDP2400_CPLD_INT_STAT, IXDP2400_CPLD_INT_MASK, IXDP2400_NR_IRQS);
-}
-
-MACHINE_START(IXDP2400, "Intel IXDP2400 Development Platform")
-	/* Maintainer: MontaVista Software, Inc. */
-	.atag_offset	= 0x100,
-	.map_io		= ixdp2x00_map_io,
-	.init_irq	= ixdp2400_init_irq,
-	.timer		= &ixdp2400_timer,
-	.init_machine	= ixdp2x00_init_machine,
-	.restart	= ixp2000_restart,
-MACHINE_END
-
diff --git a/arch/arm/mach-ixp2000/ixdp2800.c b/arch/arm/mach-ixp2000/ixdp2800.c
deleted file mode 100644
index a9f1819..0000000
--- a/arch/arm/mach-ixp2000/ixdp2800.c
+++ /dev/null
@@ -1,295 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/ixdp2800.c
- *
- * IXDP2800 platform support
- *
- * Original Author: Jeffrey Daly <jeffrey.daly@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/arch.h>
-
-/*************************************************************************
- * IXDP2800 timer tick
- *************************************************************************/
-
-static void __init ixdp2800_timer_init(void)
-{
-	ixp2000_init_time(50000000);
-}
-
-static struct sys_timer ixdp2800_timer = {
-	.init		= ixdp2800_timer_init,
-	.offset		= ixp2000_gettimeoffset,
-};
-
-/*************************************************************************
- * IXDP2800 PCI
- *************************************************************************/
-static void __init ixdp2800_slave_disable_pci_master(void)
-{
-	*IXP2000_PCI_CMDSTAT &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
-}
-
-static void __init ixdp2800_master_wait_for_slave(void)
-{
-	volatile u32 *addr;
-
-	printk(KERN_INFO "IXDP2800: waiting for slave NPU to configure "
-			 "its BAR sizes\n");
-
-	addr = ixp2000_pci_config_addr(0, IXDP2X00_SLAVE_NPU_DEVFN,
-					PCI_BASE_ADDRESS_1);
-	do {
-		*addr = 0xffffffff;
-		cpu_relax();
-	} while (*addr != 0xfe000008);
-
-	addr = ixp2000_pci_config_addr(0, IXDP2X00_SLAVE_NPU_DEVFN,
-					PCI_BASE_ADDRESS_2);
-	do {
-		*addr = 0xffffffff;
-		cpu_relax();
-	} while (*addr != 0xc0000008);
-
-	/*
-	 * Configure the slave's SDRAM BAR by hand.
-	 */
-	*addr = 0x40000008;
-}
-
-static void __init ixdp2800_slave_wait_for_master_enable(void)
-{
-	printk(KERN_INFO "IXDP2800: waiting for master NPU to enable us\n");
-
-	while ((*IXP2000_PCI_CMDSTAT & PCI_COMMAND_MASTER) == 0)
-		cpu_relax();
-}
-
-void __init ixdp2800_pci_preinit(void)
-{
-	printk("ixdp2x00_pci_preinit called\n");
-
-	*IXP2000_PCI_ADDR_EXT = 0x0001e000;
-
-	if (!ixdp2x00_master_npu())
-		ixdp2800_slave_disable_pci_master();
-
-	*IXP2000_PCI_SRAM_BASE_ADDR_MASK = (0x2000000 - 1) & ~0x3ffff;
-	*IXP2000_PCI_DRAM_BASE_ADDR_MASK = (0x40000000 - 1) & ~0xfffff;
-
-	ixp2000_pci_preinit();
-
-	if (ixdp2x00_master_npu()) {
-		/*
-		 * Wait until the slave set its SRAM/SDRAM BAR sizes
-		 * correctly before we proceed to scan and enumerate
-		 * the bus.
-		 */
-		ixdp2800_master_wait_for_slave();
-
-		/*
-		 * We configure the SDRAM BARs by hand because they
-		 * are 1G and fall outside of the regular allocated
-		 * PCI address space.
-		 */
-		*IXP2000_PCI_SDRAM_BAR = 0x00000008;
-	} else {
-		/*
-		 * Wait for the master to complete scanning the bus
-		 * and assigning resources before we proceed to scan
-		 * the bus ourselves.  Set pci=firmware to honor the
-		 * master's resource assignment.
-		 */
-		ixdp2800_slave_wait_for_master_enable();
-		pcibios_setup("firmware");
-	}
-}
-
-/*
- * We assign the SDRAM BARs for the two IXP2800 CPUs by hand, outside
- * of the regular PCI window, because there's only 512M of outbound PCI
- * memory window on each IXP, while we need 1G for each of the BARs.
- */
-static void __devinit ixp2800_pci_fixup(struct pci_dev *dev)
-{
-	if (machine_is_ixdp2800()) {
-		dev->resource[2].start = 0;
-		dev->resource[2].end   = 0;
-		dev->resource[2].flags = 0;
-	}
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IXP2800, ixp2800_pci_fixup);
-
-static int __init ixdp2800_pci_setup(int nr, struct pci_sys_data *sys)
-{
-	sys->mem_offset = 0x00000000;
-
-	ixp2000_pci_setup(nr, sys);
-
-	return 1;
-}
-
-static int __init ixdp2800_pci_map_irq(const struct pci_dev *dev, u8 slot,
-	u8 pin)
-{
-	if (ixdp2x00_master_npu()) {
-
-		/*
-		 * Root bus devices.  Slave NPU is only one with interrupt.
-		 * Everything else, we just return -1 which is invalid.
-		 */
-		if(!dev->bus->self) {
-			if(dev->devfn == IXDP2X00_SLAVE_NPU_DEVFN )
-				return IRQ_IXDP2800_INGRESS_NPU;
-
-			return -1;
-		}
-
-		/*
-		 * Bridge behind the PMC slot.
-		 */
-		if(dev->bus->self->devfn == IXDP2X00_PMC_DEVFN &&
-			dev->bus->parent->self->devfn == IXDP2X00_P2P_DEVFN &&
-			!dev->bus->parent->self->bus->parent)
-				  return IRQ_IXDP2800_PMC;
-
-		/*
-		 * Device behind the first bridge
-		 */
-		if(dev->bus->self->devfn == IXDP2X00_P2P_DEVFN) {
-			switch(dev->devfn) {
-				case IXDP2X00_PMC_DEVFN:
-					return IRQ_IXDP2800_PMC;	
-			
-				case IXDP2800_MASTER_ENET_DEVFN:
-					return IRQ_IXDP2800_EGRESS_ENET;
-
-				case IXDP2800_SWITCH_FABRIC_DEVFN:
-					return IRQ_IXDP2800_FABRIC;
-			}
-		}
-
-		return -1;
-	} else return IRQ_IXP2000_PCIB; /* Slave NIC interrupt */
-}
-
-static void __init ixdp2800_master_enable_slave(void)
-{
-	volatile u32 *addr;
-
-	printk(KERN_INFO "IXDP2800: enabling slave NPU\n");
-
-	addr = (volatile u32 *)ixp2000_pci_config_addr(0,
-					IXDP2X00_SLAVE_NPU_DEVFN,
-					PCI_COMMAND);
-
-	*addr |= PCI_COMMAND_MASTER;
-}
-
-static void __init ixdp2800_master_wait_for_slave_bus_scan(void)
-{
-	volatile u32 *addr;
-
-	printk(KERN_INFO "IXDP2800: waiting for slave to finish bus scan\n");
-
-	addr = (volatile u32 *)ixp2000_pci_config_addr(0,
-					IXDP2X00_SLAVE_NPU_DEVFN,
-					PCI_COMMAND);
-	while ((*addr & PCI_COMMAND_MEMORY) == 0)
-		cpu_relax();
-}
-
-static void __init ixdp2800_slave_signal_bus_scan_completion(void)
-{
-	printk(KERN_INFO "IXDP2800: bus scan done, signaling master\n");
-	*IXP2000_PCI_CMDSTAT |= PCI_COMMAND_MEMORY;
-}
-
-static void __init ixdp2800_pci_postinit(void)
-{
-	if (!ixdp2x00_master_npu()) {
-		ixdp2x00_slave_pci_postinit();
-		ixdp2800_slave_signal_bus_scan_completion();
-	}
-}
-
-struct __initdata hw_pci ixdp2800_pci __initdata = {
-	.nr_controllers	= 1,
-	.setup		= ixdp2800_pci_setup,
-	.preinit	= ixdp2800_pci_preinit,
-	.postinit	= ixdp2800_pci_postinit,
-	.scan		= ixp2000_pci_scan_bus,
-	.map_irq	= ixdp2800_pci_map_irq,
-};
-
-int __init ixdp2800_pci_init(void)
-{
-	if (machine_is_ixdp2800()) {
-		struct pci_dev *dev;
-
-		pci_common_init(&ixdp2800_pci);
-		if (ixdp2x00_master_npu()) {
-			dev = pci_get_bus_and_slot(1, IXDP2800_SLAVE_ENET_DEVFN);
-			pci_stop_and_remove_bus_device(dev);
-			pci_dev_put(dev);
-
-			ixdp2800_master_enable_slave();
-			ixdp2800_master_wait_for_slave_bus_scan();
-		} else {
-			dev = pci_get_bus_and_slot(1, IXDP2800_MASTER_ENET_DEVFN);
-			pci_stop_and_remove_bus_device(dev);
-			pci_dev_put(dev);
-		}
-	}
-
-	return 0;
-}
-
-subsys_initcall(ixdp2800_pci_init);
-
-void __init ixdp2800_init_irq(void)
-{
-	ixdp2x00_init_irq(IXDP2800_CPLD_INT_STAT, IXDP2800_CPLD_INT_MASK, IXDP2800_NR_IRQS);
-}
-
-MACHINE_START(IXDP2800, "Intel IXDP2800 Development Platform")
-	/* Maintainer: MontaVista Software, Inc. */
-	.atag_offset	= 0x100,
-	.map_io		= ixdp2x00_map_io,
-	.init_irq	= ixdp2800_init_irq,
-	.timer		= &ixdp2800_timer,
-	.init_machine	= ixdp2x00_init_machine,
-	.restart	= ixp2000_restart,
-MACHINE_END
-
diff --git a/arch/arm/mach-ixp2000/ixdp2x00.c b/arch/arm/mach-ixp2000/ixdp2x00.c
deleted file mode 100644
index 421e38d..0000000
--- a/arch/arm/mach-ixp2000/ixdp2x00.c
+++ /dev/null
@@ -1,306 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/ixdp2x00.c
- *
- * Code common to IXDP2400 and IXDP2800 platforms.
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/arch.h>
-
-#include <mach/gpio-ixp2000.h>
-
-/*************************************************************************
- * IXDP2x00 IRQ Initialization
- *************************************************************************/
-static volatile unsigned long *board_irq_mask;
-static volatile unsigned long *board_irq_stat;
-static unsigned long board_irq_count;
-
-#ifdef CONFIG_ARCH_IXDP2400
-/*
- * Slowport configuration for accessing CPLD registers on IXDP2x00
- */
-static struct slowport_cfg slowport_cpld_cfg = {
-	.CCR =	SLOWPORT_CCR_DIV_2,
-	.WTC = 0x00000070,
-	.RTC = 0x00000070,
-	.PCR = SLOWPORT_MODE_FLASH,
-	.ADC = SLOWPORT_ADDR_WIDTH_24 | SLOWPORT_DATA_WIDTH_8
-};
-#endif
-
-static void ixdp2x00_irq_mask(struct irq_data *d)
-{
-	unsigned long dummy;
-	static struct slowport_cfg old_cfg;
-
-	/*
-	 * This is ugly in common code but really don't know
-	 * of a better way to handle it. :(
-	 */
-#ifdef CONFIG_ARCH_IXDP2400
-	if (machine_is_ixdp2400())
-		ixp2000_acquire_slowport(&slowport_cpld_cfg, &old_cfg);
-#endif
-
-	dummy = *board_irq_mask;
-	dummy |=  IXP2000_BOARD_IRQ_MASK(d->irq);
-	ixp2000_reg_wrb(board_irq_mask, dummy);
-
-#ifdef CONFIG_ARCH_IXDP2400
-	if (machine_is_ixdp2400())
-		ixp2000_release_slowport(&old_cfg);
-#endif
-}
-
-static void ixdp2x00_irq_unmask(struct irq_data *d)
-{
-	unsigned long dummy;
-	static struct slowport_cfg old_cfg;
-
-#ifdef CONFIG_ARCH_IXDP2400
-	if (machine_is_ixdp2400())
-		ixp2000_acquire_slowport(&slowport_cpld_cfg, &old_cfg);
-#endif
-
-	dummy = *board_irq_mask;
-	dummy &=  ~IXP2000_BOARD_IRQ_MASK(d->irq);
-	ixp2000_reg_wrb(board_irq_mask, dummy);
-
-	if (machine_is_ixdp2400()) 
-		ixp2000_release_slowport(&old_cfg);
-}
-
-static void ixdp2x00_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-        volatile u32 ex_interrupt = 0;
-	static struct slowport_cfg old_cfg;
-	int i;
-
-	desc->irq_data.chip->irq_mask(&desc->irq_data);
-
-#ifdef CONFIG_ARCH_IXDP2400
-	if (machine_is_ixdp2400())
-		ixp2000_acquire_slowport(&slowport_cpld_cfg, &old_cfg);
-#endif
-        ex_interrupt = *board_irq_stat & 0xff;
-	if (machine_is_ixdp2400())
-		ixp2000_release_slowport(&old_cfg);
-
-	if(!ex_interrupt) {
-		printk(KERN_ERR "Spurious IXDP2x00 CPLD interrupt!\n");
-		return;
-	}
-
-	for(i = 0; i < board_irq_count; i++) {
-		if(ex_interrupt & (1 << i))  {
-			int cpld_irq = IXP2000_BOARD_IRQ(0) + i;
-			generic_handle_irq(cpld_irq);
-		}
-	}
-
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2x00_cpld_irq_chip = {
-	.irq_ack	= ixdp2x00_irq_mask,
-	.irq_mask	= ixdp2x00_irq_mask,
-	.irq_unmask	= ixdp2x00_irq_unmask
-};
-
-void __init ixdp2x00_init_irq(volatile unsigned long *stat_reg, volatile unsigned long *mask_reg, unsigned long nr_of_irqs)
-{
-	unsigned int irq;
-
-	ixp2000_init_irq();
-	
-	if (!ixdp2x00_master_npu())
-		return;
-
-	board_irq_stat = stat_reg;
-	board_irq_mask = mask_reg;
-	board_irq_count = nr_of_irqs;
-
-	*board_irq_mask = 0xffffffff;
-
-	for(irq = IXP2000_BOARD_IRQ(0); irq < IXP2000_BOARD_IRQ(board_irq_count); irq++) {
-		irq_set_chip_and_handler(irq, &ixdp2x00_cpld_irq_chip,
-					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID);
-	}
-
-	/* Hook into PCI interrupt */
-	irq_set_chained_handler(IRQ_IXP2000_PCIB, ixdp2x00_irq_handler);
-}
-
-/*************************************************************************
- * IXDP2x00 memory map
- *************************************************************************/
-static struct map_desc ixdp2x00_io_desc __initdata = {
-	.virtual	= IXDP2X00_VIRT_CPLD_BASE, 
-	.pfn		= __phys_to_pfn(IXDP2X00_PHYS_CPLD_BASE),
-	.length		= IXDP2X00_CPLD_SIZE,
-	.type		= MT_DEVICE
-};
-
-void __init ixdp2x00_map_io(void)
-{
-	ixp2000_map_io();	
-
-	iotable_init(&ixdp2x00_io_desc, 1);
-}
-
-/*************************************************************************
- * IXDP2x00-common PCI init
- *
- * The IXDP2[48]00 has a horrid PCI bus layout. Basically the board 
- * contains two NPUs (ingress and egress) connected over PCI,  both running 
- * instances  of the kernel. So far so good. Peers on the PCI bus running 
- * Linux is a common design in telecom systems. The problem is that instead 
- * of all the devices being controlled by a single host, different
- * devices are controlled by different NPUs on the same bus, leading to
- * multiple hosts on the bus. The exact bus layout looks like:
- *
- *                   Bus 0
- *    Master NPU <-------------------+-------------------> Slave NPU
- *                                   |
- *                                   |
- *                                  P2P 
- *                                   |
- *
- *                  Bus 1            |
- *               <--+------+---------+---------+------+-->
- *                  |      |         |         |      |
- *                  |      |         |         |      |
- *             ... Dev    PMC       Media     Eth0   Eth1 ...
- *
- * The master controls all but Eth1, which is controlled by the
- * slave. What this means is that the both the master and the slave
- * have to scan the bus, but only one of them can enumerate the bus.
- * In addition, after the bus is scanned, each kernel must remove
- * the device(s) it does not control from the PCI dev list otherwise
- * a driver on each NPU will try to manage it and we will have horrible
- * conflicts. Oh..and the slave NPU needs to see the master NPU
- * for Intel's drivers to work properly. Closed source drivers...
- *
- * The way we deal with this is fairly simple but ugly:
- *
- * 1) Let master scan and enumerate the bus completely.
- * 2) Master deletes Eth1 from device list.
- * 3) Slave scans bus and then deletes all but Eth1 (Eth0 on slave)
- *    from device list.
- * 4) Find HW designers and LART them.
- *
- * The boards also do not do normal PCI IRQ routing, or any sort of 
- * sensical  swizzling, so we just need to check where on the  bus a
- * device sits and figure out to which CPLD pin the interrupt is routed.
- * See ixdp2[48]00.c files.
- *
- *************************************************************************/
-void ixdp2x00_slave_pci_postinit(void)
-{
-	struct pci_dev *dev;
-
-	/*
-	 * Remove PMC device is there is one
-	 */
-	if((dev = pci_get_bus_and_slot(1, IXDP2X00_PMC_DEVFN))) {
-		pci_stop_and_remove_bus_device(dev);
-		pci_dev_put(dev);
-	}
-
-	dev = pci_get_bus_and_slot(0, IXDP2X00_21555_DEVFN);
-	pci_stop_and_remove_bus_device(dev);
-	pci_dev_put(dev);
-}
-
-/**************************************************************************
- * IXDP2x00 Machine Setup
- *************************************************************************/
-static struct flash_platform_data ixdp2x00_platform_data = {
-	.map_name	= "cfi_probe",
-	.width		= 1,
-};
-
-static struct ixp2000_flash_data ixdp2x00_flash_data = {
-	.platform_data	= &ixdp2x00_platform_data,
-	.nr_banks	= 1
-};
-
-static struct resource ixdp2x00_flash_resource = {
-	.start		= 0xc4000000,
-	.end		= 0xc4000000 + 0x00ffffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x00_flash = {
-	.name		= "IXP2000-Flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &ixdp2x00_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &ixdp2x00_flash_resource,
-};
-
-static struct ixp2000_i2c_pins ixdp2x00_i2c_gpio_pins = {
-	.sda_pin	= IXDP2X00_GPIO_SDA,
-	.scl_pin	= IXDP2X00_GPIO_SCL,
-};
-
-static struct platform_device ixdp2x00_i2c_controller = {
-	.name		= "IXP2000-I2C",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &ixdp2x00_i2c_gpio_pins,
-	},
-	.num_resources	= 0
-};
-
-static struct platform_device *ixdp2x00_devices[] __initdata = {
-	&ixdp2x00_flash,
-	&ixdp2x00_i2c_controller
-};
-
-void __init ixdp2x00_init_machine(void)
-{
-	gpio_line_set(IXDP2X00_GPIO_I2C_ENABLE, 1);
-	gpio_line_config(IXDP2X00_GPIO_I2C_ENABLE, GPIO_OUT);
-
-	platform_add_devices(ixdp2x00_devices, ARRAY_SIZE(ixdp2x00_devices));
-	ixp2000_uart_init();
-}
-
diff --git a/arch/arm/mach-ixp2000/ixdp2x01.c b/arch/arm/mach-ixp2000/ixdp2x01.c
deleted file mode 100644
index 5196c39..0000000
--- a/arch/arm/mach-ixp2000/ixdp2x01.c
+++ /dev/null
@@ -1,483 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/ixdp2x01.c
- *
- * Code common to Intel IXDP2401 and IXDP2801 platforms
- *
- * Original Author: Andrzej Mialkowski <andrzej.mialkowski@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002-2003 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/bitops.h>
-#include <linux/pci.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_core.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-/*************************************************************************
- * IXDP2x01 IRQ Handling
- *************************************************************************/
-static void ixdp2x01_irq_mask(struct irq_data *d)
-{
-	ixp2000_reg_wrb(IXDP2X01_INT_MASK_SET_REG,
-				IXP2000_BOARD_IRQ_MASK(d->irq));
-}
-
-static void ixdp2x01_irq_unmask(struct irq_data *d)
-{
-	ixp2000_reg_write(IXDP2X01_INT_MASK_CLR_REG,
-				IXP2000_BOARD_IRQ_MASK(d->irq));
-}
-
-static u32 valid_irq_mask;
-
-static void ixdp2x01_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	u32 ex_interrupt;
-	int i;
-
-	desc->irq_data.chip->irq_mask(&desc->irq_data);
-
-	ex_interrupt = *IXDP2X01_INT_STAT_REG & valid_irq_mask;
-
-	if (!ex_interrupt) {
-		printk(KERN_ERR "Spurious IXDP2X01 CPLD interrupt!\n");
-		return;
-	}
-
-	for (i = 0; i < IXP2000_BOARD_IRQS; i++) {
-		if (ex_interrupt & (1 << i)) {
-			int cpld_irq = IXP2000_BOARD_IRQ(0) + i;
-			generic_handle_irq(cpld_irq);
-		}
-	}
-
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2x01_irq_chip = {
-	.irq_mask	= ixdp2x01_irq_mask,
-	.irq_ack	= ixdp2x01_irq_mask,
-	.irq_unmask	= ixdp2x01_irq_unmask
-};
-
-/*
- * We only do anything if we are the master NPU on the board.
- * The slave NPU only has the ethernet chip going directly to
- * the PCIB interrupt input.
- */
-void __init ixdp2x01_init_irq(void)
-{
-	int irq = 0;
-
-	/* initialize chip specific interrupts */
-	ixp2000_init_irq();
-
-	if (machine_is_ixdp2401())
-		valid_irq_mask = IXDP2401_VALID_IRQ_MASK;
-	else
-		valid_irq_mask = IXDP2801_VALID_IRQ_MASK;
-
-	/* Mask all interrupts from CPLD, disable simulation */
-	ixp2000_reg_write(IXDP2X01_INT_MASK_SET_REG, 0xffffffff);
-	ixp2000_reg_wrb(IXDP2X01_INT_SIM_REG, 0);
-
-	for (irq = NR_IXP2000_IRQS; irq < NR_IXDP2X01_IRQS; irq++) {
-		if (irq & valid_irq_mask) {
-			irq_set_chip_and_handler(irq, &ixdp2x01_irq_chip,
-						 handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID);
-		} else {
-			set_irq_flags(irq, 0);
-		}
-	}
-
-	/* Hook into PCI interrupts */
-	irq_set_chained_handler(IRQ_IXP2000_PCIB, ixdp2x01_irq_handler);
-}
-
-
-/*************************************************************************
- * IXDP2x01 memory map
- *************************************************************************/
-static struct map_desc ixdp2x01_io_desc __initdata = {
-	.virtual	= IXDP2X01_VIRT_CPLD_BASE, 
-	.pfn		= __phys_to_pfn(IXDP2X01_PHYS_CPLD_BASE),
-	.length		= IXDP2X01_CPLD_REGION_SIZE,
-	.type		= MT_DEVICE
-};
-
-static void __init ixdp2x01_map_io(void)
-{
-	ixp2000_map_io();
-	iotable_init(&ixdp2x01_io_desc, 1);
-}
-
-
-/*************************************************************************
- * IXDP2x01 serial ports
- *************************************************************************/
-static struct plat_serial8250_port ixdp2x01_serial_port1[] = {
-	{
-		.mapbase	= (unsigned long)IXDP2X01_UART1_PHYS_BASE,
-		.membase	= (char *)IXDP2X01_UART1_VIRT_BASE,
-		.irq		= IRQ_IXDP2X01_UART1,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM32,
-		.regshift	= 2,
-		.uartclk	= IXDP2X01_UART_CLK,
-	},
-	{ }
-};
-
-static struct resource ixdp2x01_uart_resource1 = {
-	.start		= IXDP2X01_UART1_PHYS_BASE,
-	.end		= IXDP2X01_UART1_PHYS_BASE + 0xffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x01_serial_device1 = {
-	.name		= "serial8250",
-	.id		= PLAT8250_DEV_PLATFORM1,
-	.dev		= {
-		.platform_data		= ixdp2x01_serial_port1,
-	},
-	.num_resources	= 1,
-	.resource	= &ixdp2x01_uart_resource1,
-};
-
-static struct plat_serial8250_port ixdp2x01_serial_port2[] = {
-	{
-		.mapbase	= (unsigned long)IXDP2X01_UART2_PHYS_BASE,
-		.membase	= (char *)IXDP2X01_UART2_VIRT_BASE,
-		.irq		= IRQ_IXDP2X01_UART2,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM32,
-		.regshift	= 2,
-		.uartclk	= IXDP2X01_UART_CLK,
-	}, 
-	{ }
-};
-
-static struct resource ixdp2x01_uart_resource2 = {
-	.start		= IXDP2X01_UART2_PHYS_BASE,
-	.end		= IXDP2X01_UART2_PHYS_BASE + 0xffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x01_serial_device2 = {
-	.name		= "serial8250",
-	.id		= PLAT8250_DEV_PLATFORM2,
-	.dev		= {
-		.platform_data		= ixdp2x01_serial_port2,
-	},
-	.num_resources	= 1,
-	.resource	= &ixdp2x01_uart_resource2,
-};
-
-static void ixdp2x01_uart_init(void)
-{
-	platform_device_register(&ixdp2x01_serial_device1);
-	platform_device_register(&ixdp2x01_serial_device2);
-}
-
-
-/*************************************************************************
- * IXDP2x01 timer tick configuration
- *************************************************************************/
-static unsigned int ixdp2x01_clock;
-
-static int __init ixdp2x01_clock_setup(char *str)
-{
-	ixdp2x01_clock = simple_strtoul(str, NULL, 10);
-
-	return 1;
-}
-
-__setup("ixdp2x01_clock=", ixdp2x01_clock_setup);
-
-static void __init ixdp2x01_timer_init(void)
-{
-	if (!ixdp2x01_clock)
-		ixdp2x01_clock = 50000000;
-
-	ixp2000_init_time(ixdp2x01_clock);
-}
-
-static struct sys_timer ixdp2x01_timer = {
-	.init		= ixdp2x01_timer_init,
-	.offset		= ixp2000_gettimeoffset,
-};
-
-/*************************************************************************
- * IXDP2x01 PCI
- *************************************************************************/
-void __init ixdp2x01_pci_preinit(void)
-{
-	ixp2000_reg_write(IXP2000_PCI_ADDR_EXT, 0x00000000);
-	ixp2000_pci_preinit();
-	pcibios_setup("firmware");
-}
-
-#define DEVPIN(dev, pin) ((pin) | ((dev) << 3))
-
-static int __init ixdp2x01_pci_map_irq(const struct pci_dev *dev, u8 slot,
-	u8 pin)
-{
-	u8 bus = dev->bus->number;
-	u32 devpin = DEVPIN(PCI_SLOT(dev->devfn), pin);
-	struct pci_bus *tmp_bus = dev->bus;
-
-	/* Primary bus, no interrupts here */
-	if (bus == 0) {
-		return -1;
-	}
-
-	/* Lookup first leaf in bus tree */
-	while ((tmp_bus->parent != NULL) && (tmp_bus->parent->parent != NULL)) {
-		tmp_bus = tmp_bus->parent;
-	}
-
-	/* Select between known bridges */
-	switch (tmp_bus->self->devfn | (tmp_bus->self->bus->number << 8)) {
-	/* Device is located after first MB bridge */
-	case 0x0008:
-		if (tmp_bus == dev->bus) {
-			/* Device is located directly after first MB bridge */
-			switch (devpin) {
-			case DEVPIN(1, 1):	/* Onboard 82546 ch 0 */
-				if (machine_is_ixdp2401())
-					return IRQ_IXDP2401_INTA_82546;
-				return -1;
-			case DEVPIN(1, 2):	/* Onboard 82546 ch 1 */
-				if (machine_is_ixdp2401())
-					return IRQ_IXDP2401_INTB_82546;
-				return -1;
-			case DEVPIN(0, 1):	/* PMC INTA# */
-				return IRQ_IXDP2X01_SPCI_PMC_INTA;
-			case DEVPIN(0, 2):	/* PMC INTB# */
-				return IRQ_IXDP2X01_SPCI_PMC_INTB;
-			case DEVPIN(0, 3):	/* PMC INTC# */
-				return IRQ_IXDP2X01_SPCI_PMC_INTC;
-			case DEVPIN(0, 4):	/* PMC INTD# */
-				return IRQ_IXDP2X01_SPCI_PMC_INTD;
-			}
-		}
-		break;
-	case 0x0010:
-		if (tmp_bus == dev->bus) {
-			/* Device is located directly after second MB bridge */
-			/* Secondary bus of second bridge */
-			switch (devpin) {
-			case DEVPIN(0, 1):	/* DB#0 */
-				return IRQ_IXDP2X01_SPCI_DB_0;
-			case DEVPIN(1, 1):	/* DB#1 */
-				return IRQ_IXDP2X01_SPCI_DB_1;
-			}
-		} else {
-			/* Device is located indirectly after second MB bridge */
-			/* Not supported now */
-		}
-		break;
-	}
-
-	return -1;
-}
-
-
-static int ixdp2x01_pci_setup(int nr, struct pci_sys_data *sys)
-{
-	sys->mem_offset = 0xe0000000;
-
-	if (machine_is_ixdp2801() || machine_is_ixdp28x5())
-		sys->mem_offset -= ((*IXP2000_PCI_ADDR_EXT & 0xE000) << 16);
-
-	return ixp2000_pci_setup(nr, sys);
-}
-
-struct hw_pci ixdp2x01_pci __initdata = {
-	.nr_controllers	= 1,
-	.setup		= ixdp2x01_pci_setup,
-	.preinit	= ixdp2x01_pci_preinit,
-	.scan		= ixp2000_pci_scan_bus,
-	.map_irq	= ixdp2x01_pci_map_irq,
-};
-
-int __init ixdp2x01_pci_init(void)
-{
-	if (machine_is_ixdp2401() || machine_is_ixdp2801() ||\
-		machine_is_ixdp28x5())
-		pci_common_init(&ixdp2x01_pci);
-
-	return 0;
-}
-
-subsys_initcall(ixdp2x01_pci_init);
-
-/*************************************************************************
- * IXDP2x01 Machine Initialization
- *************************************************************************/
-static struct flash_platform_data ixdp2x01_flash_platform_data = {
-	.map_name	= "cfi_probe",
-	.width		= 1,
-};
-
-static unsigned long ixdp2x01_flash_bank_setup(unsigned long ofs)
-{
-	ixp2000_reg_wrb(IXDP2X01_CPLD_FLASH_REG,
-		((ofs >> IXDP2X01_FLASH_WINDOW_BITS) | IXDP2X01_CPLD_FLASH_INTERN));
-	return (ofs & IXDP2X01_FLASH_WINDOW_MASK);
-}
-
-static struct ixp2000_flash_data ixdp2x01_flash_data = {
-	.platform_data	= &ixdp2x01_flash_platform_data,
-	.bank_setup	= ixdp2x01_flash_bank_setup
-};
-
-static struct resource ixdp2x01_flash_resource = {
-	.start		= 0xc4000000,
-	.end		= 0xc4000000 + 0x01ffffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2x01_flash = {
-	.name		= "IXP2000-Flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &ixdp2x01_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &ixdp2x01_flash_resource,
-};
-
-static struct ixp2000_i2c_pins ixdp2x01_i2c_gpio_pins = {
-	.sda_pin	= IXDP2X01_GPIO_SDA,
-	.scl_pin	= IXDP2X01_GPIO_SCL,
-};
-
-static struct platform_device ixdp2x01_i2c_controller = {
-	.name		= "IXP2000-I2C",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &ixdp2x01_i2c_gpio_pins,
-	},
-	.num_resources	= 0
-};
-
-static struct platform_device *ixdp2x01_devices[] __initdata = {
-	&ixdp2x01_flash,
-	&ixdp2x01_i2c_controller
-};
-
-static void __init ixdp2x01_init_machine(void)
-{
-	ixp2000_reg_wrb(IXDP2X01_CPLD_FLASH_REG,
-		(IXDP2X01_CPLD_FLASH_BANK_MASK | IXDP2X01_CPLD_FLASH_INTERN));
-	
-	ixdp2x01_flash_data.nr_banks =
-		((*IXDP2X01_CPLD_FLASH_REG & IXDP2X01_CPLD_FLASH_BANK_MASK) + 1);
-
-	platform_add_devices(ixdp2x01_devices, ARRAY_SIZE(ixdp2x01_devices));
-	ixp2000_uart_init();
-	ixdp2x01_uart_init();
-}
-
-static void ixdp2401_restart(char mode, const char *cmd)
-{
-	/*
-	 * Reset flash banking register so that we are pointing at
-	 * RedBoot bank.
-	 */
-	ixp2000_reg_write(IXDP2X01_CPLD_FLASH_REG,
-				((0 >> IXDP2X01_FLASH_WINDOW_BITS)
-					| IXDP2X01_CPLD_FLASH_INTERN));
-	ixp2000_reg_wrb(IXDP2X01_CPLD_RESET_REG, 0xffffffff);
-
-	ixp2000_restart(mode, cmd);
-}
-
-static void ixdp280x_restart(char mode, const char *cmd)
-{
-	/*
-	 * On IXDP2801 we need to write this magic sequence to the CPLD
-	 * to cause a complete reset of the CPU and all external devices
-	 * and move the flash bank register back to 0.
-	 */
-	unsigned long reset_reg = *IXDP2X01_CPLD_RESET_REG;
-
-	reset_reg = 0x55AA0000 | (reset_reg & 0x0000FFFF);
-	ixp2000_reg_write(IXDP2X01_CPLD_RESET_REG, reset_reg);
-	ixp2000_reg_wrb(IXDP2X01_CPLD_RESET_REG, 0x80000000);
-
-	ixp2000_restart(mode, cmd);
-}
-
-#ifdef CONFIG_ARCH_IXDP2401
-MACHINE_START(IXDP2401, "Intel IXDP2401 Development Platform")
-	/* Maintainer: MontaVista Software, Inc. */
-	.atag_offset	= 0x100,
-	.map_io		= ixdp2x01_map_io,
-	.init_irq	= ixdp2x01_init_irq,
-	.timer		= &ixdp2x01_timer,
-	.init_machine	= ixdp2x01_init_machine,
-	.restart	= ixdp2401_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_ARCH_IXDP2801
-MACHINE_START(IXDP2801, "Intel IXDP2801 Development Platform")
-	/* Maintainer: MontaVista Software, Inc. */
-	.atag_offset	= 0x100,
-	.map_io		= ixdp2x01_map_io,
-	.init_irq	= ixdp2x01_init_irq,
-	.timer		= &ixdp2x01_timer,
-	.init_machine	= ixdp2x01_init_machine,
-	.restart	= ixdp280x_restart,
-MACHINE_END
-
-/*
- * IXDP28x5 is basically an IXDP2801 with a different CPU but Intel
- * changed the machine ID in the bootloader
- */
-MACHINE_START(IXDP28X5, "Intel IXDP2805/2855 Development Platform")
-	/* Maintainer: MontaVista Software, Inc. */
-	.atag_offset	= 0x100,
-	.map_io		= ixdp2x01_map_io,
-	.init_irq	= ixdp2x01_init_irq,
-	.timer		= &ixdp2x01_timer,
-	.init_machine	= ixdp2x01_init_machine,
-	.restart	= ixdp280x_restart,
-MACHINE_END
-#endif
-
-
diff --git a/arch/arm/mach-ixp2000/pci.c b/arch/arm/mach-ixp2000/pci.c
deleted file mode 100644
index 9c02de9..0000000
--- a/arch/arm/mach-ixp2000/pci.c
+++ /dev/null
@@ -1,252 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/pci.c
- *
- * PCI routines for IXDP2400/IXDP2800 boards
- *
- * Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Maintained by: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2002 Intel Corp.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- */
-
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <asm/mach/pci.h>
-
-static volatile int pci_master_aborts = 0;
-
-static int clear_master_aborts(void);
-
-u32 *
-ixp2000_pci_config_addr(unsigned int bus_nr, unsigned int devfn, int where)
-{
-	u32 *paddress;
-
-	if (PCI_SLOT(devfn) > 7)
-		return 0;
-
-	/* Must be dword aligned */
-	where &= ~3;
-
-	/*
-	 * For top bus, generate type 0, else type 1
-	 */
-	if (!bus_nr) {
-		/* only bits[23:16] are used for IDSEL */
-		paddress = (u32 *) (IXP2000_PCI_CFG0_VIRT_BASE
-				    | (1 << (PCI_SLOT(devfn) + 16))
-				    | (PCI_FUNC(devfn) << 8) | where);
-	} else {
-		paddress = (u32 *) (IXP2000_PCI_CFG1_VIRT_BASE 
-				    | (bus_nr << 16)
-				    | (PCI_SLOT(devfn) << 11)
-				    | (PCI_FUNC(devfn) << 8) | where);
-	}
-
-	return paddress;
-}
-
-/*
- * Mask table, bits to mask for quantity of size 1, 2 or 4 bytes.
- * 0 and 3 are not valid indexes...
- */
-static u32 bytemask[] = {
-	/*0*/	0,
-	/*1*/	0xff,
-	/*2*/	0xffff,
-	/*3*/	0,
-	/*4*/	0xffffffff,
-};
-
-
-int ixp2000_pci_read_config(struct pci_bus *bus, unsigned int devfn, int where,
-				int size, u32 *value)
-{
-	u32 n;
-	u32 *addr;
-
-	n = where % 4;
-
-	addr = ixp2000_pci_config_addr(bus->number, devfn, where);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	pci_master_aborts = 0;
-	*value = (*addr >> (8*n)) & bytemask[size];
-	if (pci_master_aborts) {
-		pci_master_aborts = 0;
-		*value = 0xffffffff;
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	}
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-/*
- * We don't do error checks by calling clear_master_aborts() b/c the
- * assumption is that the caller did a read first to make sure a device
- * exists.
- */
-int ixp2000_pci_write_config(struct pci_bus *bus, unsigned int devfn, int where,
-				int size, u32 value)
-{
-	u32 mask;
-	u32 *addr;
-	u32 temp;
-
-	mask = ~(bytemask[size] << ((where % 0x4) * 8));
-	addr = ixp2000_pci_config_addr(bus->number, devfn, where);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	temp = (u32) (value) << ((where % 0x4) * 8);
-	*addr = (*addr & mask) | temp;
-
-	clear_master_aborts();
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-
-static struct pci_ops ixp2000_pci_ops = {
-	.read	= ixp2000_pci_read_config,
-	.write	= ixp2000_pci_write_config
-};
-
-struct pci_bus *ixp2000_pci_scan_bus(int nr, struct pci_sys_data *sysdata)
-{
-	return pci_scan_root_bus(NULL, sysdata->busnr, &ixp2000_pci_ops,
-				 sysdata, &sysdata->resources);
-}
-
-
-int ixp2000_pci_abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
-{
-
-	volatile u32 temp;
-	unsigned long flags;
-
-	pci_master_aborts = 1;
-
-	local_irq_save(flags);
-	temp = *(IXP2000_PCI_CONTROL);
-	if (temp & ((1 << 8) | (1 << 5))) {
-		ixp2000_reg_wrb(IXP2000_PCI_CONTROL, temp);
-	}
-
-	temp = *(IXP2000_PCI_CMDSTAT);
-	if (temp & (1 << 29)) {
-		while (temp & (1 << 29)) {	
-			ixp2000_reg_write(IXP2000_PCI_CMDSTAT, temp);
-			temp = *(IXP2000_PCI_CMDSTAT);
-		}
-	}
-	local_irq_restore(flags);
-
-	/*
-	 * If it was an imprecise abort, then we need to correct the
-	 * return address to be _after_ the instruction.
-	 */
-	if (fsr & (1 << 10))
-		regs->ARM_pc += 4;
-
-	return 0;
-}
-
-int
-clear_master_aborts(void)
-{
-	volatile u32 temp;
-	unsigned long flags;
-
-	local_irq_save(flags);
-	temp = *(IXP2000_PCI_CONTROL);
-	if (temp & ((1 << 8) | (1 << 5))) {
-		ixp2000_reg_wrb(IXP2000_PCI_CONTROL, temp);
-	}
-
-	temp = *(IXP2000_PCI_CMDSTAT);
-	if (temp & (1 << 29)) {
-		while (temp & (1 << 29)) {
-			ixp2000_reg_write(IXP2000_PCI_CMDSTAT, temp);
-			temp = *(IXP2000_PCI_CMDSTAT);
-		}
-	}
-	local_irq_restore(flags);
-
-	return 0;
-}
-
-void __init
-ixp2000_pci_preinit(void)
-{
-	pci_set_flags(0);
-
-	pcibios_min_io = 0;
-	pcibios_min_mem = 0;
-
-#ifndef CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO
-	/*
-	 * Configure the PCI unit to properly byteswap I/O transactions,
-	 * and verify that it worked.
-	 */
-	ixp2000_reg_write(IXP2000_PCI_CONTROL,
-			  (*IXP2000_PCI_CONTROL | PCI_CONTROL_IEE));
-
-	if ((*IXP2000_PCI_CONTROL & PCI_CONTROL_IEE) == 0)
-		panic("IXP2000: PCI I/O is broken on this ixp model, and "
-			"the needed workaround has not been configured in");
-#endif
-
-	hook_fault_code(16+6, ixp2000_pci_abort_handler, SIGBUS, 0,
-				"PCI config cycle to non-existent device");
-}
-
-
-/*
- * IXP2000 systems often have large resource requirements, so we just
- * use our own resource space.
- */
-static struct resource ixp2000_pci_mem_space = {
-	.start	= 0xe0000000,
-	.end	= 0xffffffff,
-	.flags	= IORESOURCE_MEM,
-	.name	= "PCI Mem Space"
-};
-
-static struct resource ixp2000_pci_io_space = {
-	.start	= 0x00010000,
-	.end	= 0x0001ffff,
-	.flags	= IORESOURCE_IO,
-	.name	= "PCI I/O Space"
-};
-
-int ixp2000_pci_setup(int nr, struct pci_sys_data *sys)
-{
-	if (nr >= 1)
-		return 0;
-
-	pci_add_resource_offset(&sys->resources,
-				&ixp2000_pci_io_space, sys->io_offset);
-	pci_add_resource_offset(&sys->resources,
-				&ixp2000_pci_mem_space, sys->mem_offset);
-
-	return 1;
-}
-
diff --git a/arch/arm/mach-ixp23xx/Kconfig b/arch/arm/mach-ixp23xx/Kconfig
deleted file mode 100644
index 982670e..0000000
--- a/arch/arm/mach-ixp23xx/Kconfig
+++ /dev/null
@@ -1,25 +0,0 @@
-if ARCH_IXP23XX
-
-config ARCH_SUPPORTS_BIG_ENDIAN
-	bool
-	default y
-
-menu "Intel IXP23xx Implementation Options"
-
-comment "IXP23xx Platforms"
-
-config MACH_ESPRESSO
-	bool "Support IP Fabrics Double Espresso platform"
-	help
-
-config MACH_IXDP2351
-	bool "Support Intel IXDP2351 platform"
-	help
-
-config MACH_ROADRUNNER
-	bool "Support ADI RoadRunner platform"
-	help
-
-endmenu
-
-endif
diff --git a/arch/arm/mach-ixp23xx/Makefile b/arch/arm/mach-ixp23xx/Makefile
deleted file mode 100644
index 288b371..0000000
--- a/arch/arm/mach-ixp23xx/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-#
-# Makefile for the linux kernel.
-#
-obj-y			:= core.o pci.o
-obj-m			:=
-obj-n			:=
-obj-			:=
-
-obj-$(CONFIG_MACH_ESPRESSO)	+= espresso.o
-obj-$(CONFIG_MACH_IXDP2351)	+= ixdp2351.o
-obj-$(CONFIG_MACH_ROADRUNNER)	+= roadrunner.o
diff --git a/arch/arm/mach-ixp23xx/Makefile.boot b/arch/arm/mach-ixp23xx/Makefile.boot
deleted file mode 100644
index 44fb4a71..0000000
--- a/arch/arm/mach-ixp23xx/Makefile.boot
+++ /dev/null
@@ -1,2 +0,0 @@
-   zreladdr-y	+= 0x00008000
-params_phys-y	:= 0x00000100
diff --git a/arch/arm/mach-ixp23xx/core.c b/arch/arm/mach-ixp23xx/core.c
deleted file mode 100644
index d345424..0000000
--- a/arch/arm/mach-ixp23xx/core.c
+++ /dev/null
@@ -1,455 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/core.c
- *
- * Core routines for IXP23xx chips
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * Based on 2.4 code Copyright 2004 (c) Intel Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/time.h>
-#include <linux/timex.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-#include <asm/system_misc.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-
-
-/*************************************************************************
- * Chip specific mappings shared by all IXP23xx systems
- *************************************************************************/
-static struct map_desc ixp23xx_io_desc[] __initdata = {
-	{ /* XSI-CPP CSRs */
-	 	.virtual	= IXP23XX_XSI2CPP_CSR_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_XSI2CPP_CSR_PHYS),
-	 	.length		= IXP23XX_XSI2CPP_CSR_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* Expansion Bus Config */
-	 	.virtual	= IXP23XX_EXP_CFG_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_EXP_CFG_PHYS),
-	 	.length		= IXP23XX_EXP_CFG_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* UART, Interrupt ctrl, GPIO, timers, NPEs, MACS,.... */
-	 	.virtual	= IXP23XX_PERIPHERAL_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_PERIPHERAL_PHYS),
-	 	.length		= IXP23XX_PERIPHERAL_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* CAP CSRs */
-	 	.virtual	= IXP23XX_CAP_CSR_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_CAP_CSR_PHYS),
-	 	.length		= IXP23XX_CAP_CSR_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* MSF CSRs */
-	 	.virtual	= IXP23XX_MSF_CSR_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_MSF_CSR_PHYS),
-	 	.length		= IXP23XX_MSF_CSR_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* PCI I/O Space */
-	 	.virtual	= IXP23XX_PCI_IO_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_PCI_IO_PHYS),
-	 	.length		= IXP23XX_PCI_IO_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* PCI Config Space */
-	 	.virtual	= IXP23XX_PCI_CFG_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_PCI_CFG_PHYS),
-	 	.length		= IXP23XX_PCI_CFG_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* PCI local CFG CSRs */
-	 	.virtual	= IXP23XX_PCI_CREG_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_PCI_CREG_PHYS),
-	 	.length		= IXP23XX_PCI_CREG_SIZE,
-		.type		= MT_DEVICE,
-	}, { /* PCI MEM Space */
-	 	.virtual	= IXP23XX_PCI_MEM_VIRT,
-	 	.pfn		= __phys_to_pfn(IXP23XX_PCI_MEM_PHYS),
-	 	.length		= IXP23XX_PCI_MEM_SIZE,
-		.type		= MT_DEVICE,
-	}
-};
-
-void __init ixp23xx_map_io(void)
-{
-	iotable_init(ixp23xx_io_desc, ARRAY_SIZE(ixp23xx_io_desc));
-}
-
-
-/***************************************************************************
- * IXP23xx Interrupt Handling
- ***************************************************************************/
-enum ixp23xx_irq_type {
-	IXP23XX_IRQ_LEVEL, IXP23XX_IRQ_EDGE
-};
-
-static void ixp23xx_config_irq(unsigned int, enum ixp23xx_irq_type);
-
-static int ixp23xx_irq_set_type(struct irq_data *d, unsigned int type)
-{
-	int line = d->irq - IRQ_IXP23XX_GPIO6 + 6;
-	u32 int_style;
-	enum ixp23xx_irq_type irq_type;
-	volatile u32 *int_reg;
-
-	/*
-	 * Only GPIOs 6-15 are wired to interrupts on IXP23xx
-	 */
-	if (line < 6 || line > 15)
-		return -EINVAL;
-
-	switch (type) {
-	case IRQ_TYPE_EDGE_BOTH:
-		int_style = IXP23XX_GPIO_STYLE_TRANSITIONAL;
-		irq_type = IXP23XX_IRQ_EDGE;
-		break;
-	case IRQ_TYPE_EDGE_RISING:
-		int_style = IXP23XX_GPIO_STYLE_RISING_EDGE;
-		irq_type = IXP23XX_IRQ_EDGE;
-		break;
-	case IRQ_TYPE_EDGE_FALLING:
-		int_style = IXP23XX_GPIO_STYLE_FALLING_EDGE;
-		irq_type = IXP23XX_IRQ_EDGE;
-		break;
-	case IRQ_TYPE_LEVEL_HIGH:
-		int_style = IXP23XX_GPIO_STYLE_ACTIVE_HIGH;
-		irq_type = IXP23XX_IRQ_LEVEL;
-		break;
-	case IRQ_TYPE_LEVEL_LOW:
-		int_style = IXP23XX_GPIO_STYLE_ACTIVE_LOW;
-		irq_type = IXP23XX_IRQ_LEVEL;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	ixp23xx_config_irq(d->irq, irq_type);
-
-	if (line >= 8) {	/* pins 8-15 */
-		line -= 8;
-		int_reg = (volatile u32 *)IXP23XX_GPIO_GPIT2R;
-	} else {		/* pins 0-7 */
-		int_reg = (volatile u32 *)IXP23XX_GPIO_GPIT1R;
-	}
-
-	/*
-	 * Clear pending interrupts
-	 */
-	*IXP23XX_GPIO_GPISR = (1 << line);
-
-	/* Clear the style for the appropriate pin */
-	*int_reg &= ~(IXP23XX_GPIO_STYLE_MASK <<
-			(line * IXP23XX_GPIO_STYLE_SIZE));
-
-	/* Set the new style */
-	*int_reg |= (int_style << (line * IXP23XX_GPIO_STYLE_SIZE));
-
-	return 0;
-}
-
-static void ixp23xx_irq_mask(struct irq_data *d)
-{
-	volatile unsigned long *intr_reg;
-	unsigned int irq = d->irq;
-
-	if (irq >= 56)
-		irq += 8;
-
-	intr_reg = IXP23XX_INTR_EN1 + (irq / 32);
-	*intr_reg &= ~(1 << (irq % 32));
-}
-
-static void ixp23xx_irq_ack(struct irq_data *d)
-{
-	int line = d->irq - IRQ_IXP23XX_GPIO6 + 6;
-
-	if ((line < 6) || (line > 15))
-		return;
-
-	*IXP23XX_GPIO_GPISR = (1 << line);
-}
-
-/*
- * Level triggered interrupts on GPIO lines can only be cleared when the
- * interrupt condition disappears.
- */
-static void ixp23xx_irq_level_unmask(struct irq_data *d)
-{
-	volatile unsigned long *intr_reg;
-	unsigned int irq = d->irq;
-
-	ixp23xx_irq_ack(d);
-
-	if (irq >= 56)
-		irq += 8;
-
-	intr_reg = IXP23XX_INTR_EN1 + (irq / 32);
-	*intr_reg |= (1 << (irq % 32));
-}
-
-static void ixp23xx_irq_edge_unmask(struct irq_data *d)
-{
-	volatile unsigned long *intr_reg;
-	unsigned int irq = d->irq;
-
-	if (irq >= 56)
-		irq += 8;
-
-	intr_reg = IXP23XX_INTR_EN1 + (irq / 32);
-	*intr_reg |= (1 << (irq % 32));
-}
-
-static struct irq_chip ixp23xx_irq_level_chip = {
-	.irq_ack	= ixp23xx_irq_mask,
-	.irq_mask	= ixp23xx_irq_mask,
-	.irq_unmask	= ixp23xx_irq_level_unmask,
-	.irq_set_type	= ixp23xx_irq_set_type
-};
-
-static struct irq_chip ixp23xx_irq_edge_chip = {
-	.irq_ack	= ixp23xx_irq_ack,
-	.irq_mask	= ixp23xx_irq_mask,
-	.irq_unmask	= ixp23xx_irq_edge_unmask,
-	.irq_set_type	= ixp23xx_irq_set_type
-};
-
-static void ixp23xx_pci_irq_mask(struct irq_data *d)
-{
-	unsigned int irq = d->irq;
-
-	*IXP23XX_PCI_XSCALE_INT_ENABLE &= ~(1 << (IRQ_IXP23XX_INTA + 27 - irq));
-}
-
-static void ixp23xx_pci_irq_unmask(struct irq_data *d)
-{
-	unsigned int irq = d->irq;
-
-	*IXP23XX_PCI_XSCALE_INT_ENABLE |= (1 << (IRQ_IXP23XX_INTA + 27 - irq));
-}
-
-/*
- * TODO: Should this just be done at ASM level?
- */
-static void pci_handler(unsigned int irq, struct irq_desc *desc)
-{
-	u32 pci_interrupt;
-	unsigned int irqno;
-
-	pci_interrupt = *IXP23XX_PCI_XSCALE_INT_STATUS;
-
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-
-	/* See which PCI_INTA, or PCI_INTB interrupted */
-	if (pci_interrupt & (1 << 26)) {
-		irqno = IRQ_IXP23XX_INTB;
-	} else if (pci_interrupt & (1 << 27)) {
-		irqno = IRQ_IXP23XX_INTA;
-	} else {
-		BUG();
-	}
-
-	generic_handle_irq(irqno);
-
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixp23xx_pci_irq_chip = {
-	.irq_ack	= ixp23xx_pci_irq_mask,
-	.irq_mask	= ixp23xx_pci_irq_mask,
-	.irq_unmask	= ixp23xx_pci_irq_unmask
-};
-
-static void ixp23xx_config_irq(unsigned int irq, enum ixp23xx_irq_type type)
-{
-	switch (type) {
-	case IXP23XX_IRQ_LEVEL:
-		irq_set_chip_and_handler(irq, &ixp23xx_irq_level_chip,
-					 handle_level_irq);
-		break;
-	case IXP23XX_IRQ_EDGE:
-		irq_set_chip_and_handler(irq, &ixp23xx_irq_edge_chip,
-					 handle_edge_irq);
-		break;
-	}
-	set_irq_flags(irq, IRQF_VALID);
-}
-
-void __init ixp23xx_init_irq(void)
-{
-	int irq;
-
-	/* Route everything to IRQ */
-	*IXP23XX_INTR_SEL1 = 0x0;
-	*IXP23XX_INTR_SEL2 = 0x0;
-	*IXP23XX_INTR_SEL3 = 0x0;
-	*IXP23XX_INTR_SEL4 = 0x0;
-
-	/* Mask all sources */
-	*IXP23XX_INTR_EN1 = 0x0;
-	*IXP23XX_INTR_EN2 = 0x0;
-	*IXP23XX_INTR_EN3 = 0x0;
-	*IXP23XX_INTR_EN4 = 0x0;
-
-	/*
-	 * Configure all IRQs for level-sensitive operation
-	 */
-	for (irq = 0; irq <= NUM_IXP23XX_RAW_IRQS; irq++) {
-		ixp23xx_config_irq(irq, IXP23XX_IRQ_LEVEL);
-	}
-
-	for (irq = IRQ_IXP23XX_INTA; irq <= IRQ_IXP23XX_INTB; irq++) {
-		irq_set_chip_and_handler(irq, &ixp23xx_pci_irq_chip,
-					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID);
-	}
-
-	irq_set_chained_handler(IRQ_IXP23XX_PCI_INT_RPH, pci_handler);
-}
-
-
-/*************************************************************************
- * Timer-tick functions for IXP23xx
- *************************************************************************/
-#define CLOCK_TICKS_PER_USEC	(CLOCK_TICK_RATE / USEC_PER_SEC)
-
-static unsigned long next_jiffy_time;
-
-static unsigned long
-ixp23xx_gettimeoffset(void)
-{
-	unsigned long elapsed;
-
-	elapsed = *IXP23XX_TIMER_CONT - (next_jiffy_time - LATCH);
-
-	return elapsed / CLOCK_TICKS_PER_USEC;
-}
-
-static irqreturn_t
-ixp23xx_timer_interrupt(int irq, void *dev_id)
-{
-	/* Clear Pending Interrupt by writing '1' to it */
-	*IXP23XX_TIMER_STATUS = IXP23XX_TIMER1_INT_PEND;
-	while ((signed long)(*IXP23XX_TIMER_CONT - next_jiffy_time) >= LATCH) {
-		timer_tick();
-		next_jiffy_time += LATCH;
-	}
-
-	return IRQ_HANDLED;
-}
-
-static struct irqaction ixp23xx_timer_irq = {
-	.name		= "IXP23xx Timer Tick",
-	.handler	= ixp23xx_timer_interrupt,
-	.flags		= IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
-};
-
-void __init ixp23xx_init_timer(void)
-{
-	/* Clear Pending Interrupt by writing '1' to it */
-	*IXP23XX_TIMER_STATUS = IXP23XX_TIMER1_INT_PEND;
-
-	/* Setup the Timer counter value */
-	*IXP23XX_TIMER1_RELOAD =
-		(LATCH & ~IXP23XX_TIMER_RELOAD_MASK) | IXP23XX_TIMER_ENABLE;
-
-	*IXP23XX_TIMER_CONT = 0;
-	next_jiffy_time = LATCH;
-
-	/* Connect the interrupt handler and enable the interrupt */
-	setup_irq(IRQ_IXP23XX_TIMER1, &ixp23xx_timer_irq);
-}
-
-struct sys_timer ixp23xx_timer = {
-	.init		= ixp23xx_init_timer,
-	.offset		= ixp23xx_gettimeoffset,
-};
-
-
-/*************************************************************************
- * IXP23xx Platform Initialization
- *************************************************************************/
-static struct resource ixp23xx_uart_resources[] = {
-	{
-		.start		= IXP23XX_UART1_PHYS,
-		.end		= IXP23XX_UART1_PHYS + 0x0fff,
-		.flags		= IORESOURCE_MEM
-	}, {
-		.start		= IXP23XX_UART2_PHYS,
-		.end		= IXP23XX_UART2_PHYS + 0x0fff,
-		.flags		= IORESOURCE_MEM
-	}
-};
-
-static struct plat_serial8250_port ixp23xx_uart_data[] = {
-	{
-		.mapbase	= IXP23XX_UART1_PHYS,
-		.membase	= (char *)(IXP23XX_UART1_VIRT + 3),
-		.irq		= IRQ_IXP23XX_UART1,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= IXP23XX_UART_XTAL,
-	}, {
-		.mapbase	= IXP23XX_UART2_PHYS,
-		.membase	= (char *)(IXP23XX_UART2_VIRT + 3),
-		.irq		= IRQ_IXP23XX_UART2,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= IXP23XX_UART_XTAL,
-	},
-	{ },
-};
-
-static struct platform_device ixp23xx_uart = {
-	.name			= "serial8250",
-	.id			= 0,
-	.dev.platform_data	= ixp23xx_uart_data,
-	.num_resources		= 2,
-	.resource		= ixp23xx_uart_resources,
-};
-
-static struct platform_device *ixp23xx_devices[] __initdata = {
-	&ixp23xx_uart,
-};
-
-void __init ixp23xx_sys_init(void)
-{
-	/* by default, the idle code is disabled */
-	disable_hlt();
-
-	*IXP23XX_EXP_UNIT_FUSE |= 0xf;
-	platform_add_devices(ixp23xx_devices, ARRAY_SIZE(ixp23xx_devices));
-}
-
-void ixp23xx_restart(char mode, const char *cmd)
-{
-	/* Use on-chip reset capability */
-	*IXP23XX_RESET0 |= IXP23XX_RST_ALL;
-}
diff --git a/arch/arm/mach-ixp23xx/espresso.c b/arch/arm/mach-ixp23xx/espresso.c
deleted file mode 100644
index d142d45..0000000
--- a/arch/arm/mach-ixp23xx/espresso.c
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/espresso.c
- *
- * Double Espresso-specific routines
- *
- * Author: Lennert Buytenhek <buytenh@wantstofly.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/ioport.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/pci.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-
-static int __init espresso_pci_init(void)
-{
-	if (machine_is_espresso())
-		ixp23xx_pci_slave_init();
-
-	return 0;
-};
-subsys_initcall(espresso_pci_init);
-
-static struct physmap_flash_data espresso_flash_data = {
-	.width		= 2,
-};
-
-static struct resource espresso_flash_resource = {
-	.start		= 0x90000000,
-	.end		= 0x91ffffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device espresso_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &espresso_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &espresso_flash_resource,
-};
-
-static void __init espresso_init(void)
-{
-	platform_device_register(&espresso_flash);
-
-	/*
-	 * Mark flash as writeable.
-	 */
-	IXP23XX_EXP_CS0[0] |= IXP23XX_FLASH_WRITABLE;
-	IXP23XX_EXP_CS0[1] |= IXP23XX_FLASH_WRITABLE;
-
-	ixp23xx_sys_init();
-}
-
-MACHINE_START(ESPRESSO, "IP Fabrics Double Espresso")
-	/* Maintainer: Lennert Buytenhek */
-	.map_io		= ixp23xx_map_io,
-	.init_irq	= ixp23xx_init_irq,
-	.timer		= &ixp23xx_timer,
-	.atag_offset	= 0x100,
-	.init_machine	= espresso_init,
-	.restart	= ixp23xx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-ixp23xx/include/mach/debug-macro.S b/arch/arm/mach-ixp23xx/include/mach/debug-macro.S
deleted file mode 100644
index 5ff524c..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/debug-macro.S
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <mach/ixp23xx.h>
-
-		.macro	addruart, rp, rv, tmp
-		ldr	\rp, =IXP23XX_PERIPHERAL_PHYS 	@ physical
-		ldr	\rv, =IXP23XX_PERIPHERAL_VIRT	@ virtual
-#ifdef __ARMEB__
-		orr	\rp, \rp, #0x00000003
-		orr	\rv, \rv, #0x00000003
-#endif
-		.endm
-
-#define UART_SHIFT	2
-#include <asm/hardware/debug-8250.S>
diff --git a/arch/arm/mach-ixp23xx/include/mach/entry-macro.S b/arch/arm/mach-ixp23xx/include/mach/entry-macro.S
deleted file mode 100644
index 3fd2cb9..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/entry-macro.S
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/entry-macro.S
- */
-
-		.macro  get_irqnr_preamble, base, tmp
-		.endm
-
-		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-		ldr	\irqnr, =(IXP23XX_INTC_VIRT + IXP23XX_INTR_IRQ_ENC_ST_OFFSET)
-		ldr	\irqnr, [\irqnr]	@ get interrupt number
-		cmp	\irqnr, #0x0		@ spurious interrupt ?
-		movne	\irqnr, \irqnr, lsr #2	@ skip unwanted low order bits
-		subne	\irqnr, \irqnr, #1	@ convert to 0 based
-
-#if 0
-		cmp	\irqnr, #IRQ_IXP23XX_PCI_INT_RPH
-		bne	1001f
-		mov	\irqnr, #IRQ_IXP23XX_INTA
-
-		ldr	\irqnr, =0xf5000030
-
-		mov	\tmp, #(1<<26)
-		tst	\irqnr, \tmp
-		movne	\irqnr, #IRQ_IXP23XX_INTB
-
-		mov	\tmp, #(1<<27)
-		tst	\irqnr, \tmp
-		movne	\irqnr, #IRQ_IXP23XX_INTA
-1001:
-#endif
-		.endm
diff --git a/arch/arm/mach-ixp23xx/include/mach/hardware.h b/arch/arm/mach-ixp23xx/include/mach/hardware.h
deleted file mode 100644
index 60e55fa..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/hardware.h
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/hardware.h
- *
- * Copyright (C) 2002-2004 Intel Corporation.
- * Copyricht (C) 2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Hardware definitions for IXP23XX based systems
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-/* PCI IO info */
-
-#include "ixp23xx.h"
-
-/*
- * Platform helper functions
- */
-#include "platform.h"
-
-/*
- * Platform-specific headers
- */
-#include "ixdp2351.h"
-
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/include/mach/io.h b/arch/arm/mach-ixp23xx/include/mach/io.h
deleted file mode 100644
index a7aceb5..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/io.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/io.h
- *
- * Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2003-2005 Intel Corp.
- * Copyright (C) 2005 MontaVista Software, Inc
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_IO_H
-#define __ASM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-#define __io(p)		((void __iomem*)((p) + IXP23XX_PCI_IO_VIRT))
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/include/mach/irqs.h b/arch/arm/mach-ixp23xx/include/mach/irqs.h
deleted file mode 100644
index 3af33a0..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/irqs.h
+++ /dev/null
@@ -1,223 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/irqs.h
- *
- * IRQ definitions for IXP23XX based systems
- *
- * Author: Naeem Afzal <naeem.m.afzal@intel.com>
- *
- * Copyright (C) 2003-2004 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-#define NR_IXP23XX_IRQS			IRQ_IXP23XX_INTB+1
-#define IRQ_IXP23XX_EXTIRQS		NR_IXP23XX_IRQS
-
-
-#define IRQ_IXP23XX_DBG0		0	/* Debug/Execution/MBox */
-#define IRQ_IXP23XX_DBG1		1	/* Debug/Execution/MBox */
-#define IRQ_IXP23XX_NPE_TRG		2	/* npe_trigger */
-#define IRQ_IXP23XX_TIMER1		3	/* Timer[0] */
-#define IRQ_IXP23XX_TIMER2		4	/* Timer[1] */
-#define IRQ_IXP23XX_TIMESTAMP		5	/* Timer[2], Time-stamp */
-#define IRQ_IXP23XX_WDOG		6	/* Time[3], Watchdog Timer */
-#define IRQ_IXP23XX_PCI_DBELL		7	/* PCI Doorbell */
-#define IRQ_IXP23XX_PCI_DMA1		8	/* PCI DMA Channel 1 */
-#define IRQ_IXP23XX_PCI_DMA2		9	/* PCI DMA Channel 2 */
-#define IRQ_IXP23XX_PCI_DMA3		10	/* PCI DMA Channel 3 */
-#define IRQ_IXP23XX_PCI_INT_RPH		11	/* pcxg_pci_int_rph */
-#define IRQ_IXP23XX_CPP_PMU		12	/* xpxg_pm_int_rpl */
-#define IRQ_IXP23XX_SWINT0		13	/* S/W Interrupt0 */
-#define IRQ_IXP23XX_SWINT1		14	/* S/W Interrupt1 */
-#define IRQ_IXP23XX_UART2		15	/* UART1 Interrupt */
-#define IRQ_IXP23XX_UART1		16	/* UART0 Interrupt */
-#define IRQ_IXP23XX_XSI_PMU_ROLLOVER	17	/* AHB Performance M. Unit counter rollover */
-#define IRQ_IXP23XX_XSI_AHB_PM0		18	/* intr_pm_o */
-#define IRQ_IXP23XX_XSI_AHB_ECE0	19	/* intr_ece_o */
-#define IRQ_IXP23XX_XSI_AHB_GASKET	20	/* gas_intr_o */
-#define IRQ_IXP23XX_XSI_CPP		21	/* xsi2cpp_int */
-#define IRQ_IXP23XX_CPP_XSI		22	/* cpp2xsi_int */
-#define IRQ_IXP23XX_ME_ATTN0		23	/* ME_ATTN */
-#define IRQ_IXP23XX_ME_ATTN1		24	/* ME_ATTN */
-#define IRQ_IXP23XX_ME_ATTN2		25	/* ME_ATTN */
-#define IRQ_IXP23XX_ME_ATTN3		26	/* ME_ATTN */
-#define IRQ_IXP23XX_PCI_ERR_RPH		27	/* PCXG_PCI_ERR_RPH */
-#define IRQ_IXP23XX_D0XG_ECC_CORR	28	/* D0XG_DRAM_ECC_CORR */
-#define IRQ_IXP23XX_D0XG_ECC_UNCORR	29	/* D0XG_DRAM_ECC_UNCORR */
-#define IRQ_IXP23XX_SRAM_ERR1		30	/* SRAM1_ERR */
-#define IRQ_IXP23XX_SRAM_ERR0		31	/* SRAM0_ERR */
-#define IRQ_IXP23XX_MEDIA_ERR		32	/* MEDIA_ERR */
-#define IRQ_IXP23XX_STH_DRAM_ECC_MAJ	33	/* STH_DRAM0_ECC_MAJ */
-#define IRQ_IXP23XX_GPIO6		34	/* GPIO0 interrupts */
-#define IRQ_IXP23XX_GPIO7		35	/* GPIO1 interrupts */
-#define IRQ_IXP23XX_GPIO8		36	/* GPIO2 interrupts */
-#define IRQ_IXP23XX_GPIO9		37	/* GPIO3 interrupts */
-#define IRQ_IXP23XX_GPIO10		38	/* GPIO4 interrupts */
-#define IRQ_IXP23XX_GPIO11		39	/* GPIO5 interrupts */
-#define IRQ_IXP23XX_GPIO12		40	/* GPIO6 interrupts */
-#define IRQ_IXP23XX_GPIO13		41	/* GPIO7 interrupts */
-#define IRQ_IXP23XX_GPIO14		42	/* GPIO8 interrupts */
-#define IRQ_IXP23XX_GPIO15		43	/* GPIO9 interrupts */
-#define IRQ_IXP23XX_SHAC_RING0		44	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING1		45	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING2		46	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING3		47	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING4		48	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING5		49	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING6		50	/* SHAC RING Full */
-#define IRQ_IXP23XX_SHAC_RING7		51	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING8		52	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING9		53	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING10		54	/* SHAC Ring Full */
-#define IRQ_IXP23XX_SHAC_RING11		55	/* SHAC Ring Full */
-#define IRQ_IXP23XX_ME_THREAD_A0_ME0	56	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A1_ME0	57	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A2_ME0	58	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A3_ME0	59	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A4_ME0	60	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A5_ME0	61	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A6_ME0	62	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A7_ME0	63	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A8_ME1	64	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A9_ME1	65	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A10_ME1	66	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A11_ME1	67	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A12_ME1	68	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A13_ME1	69	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A14_ME1	70	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A15_ME1	71	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A16_ME2	72	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A17_ME2	73	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A18_ME2	74	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A19_ME2	75	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A20_ME2	76	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A21_ME2	77	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A22_ME2	78	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A23_ME2	79	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A24_ME3	80	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A25_ME3	81	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A26_ME3	82	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A27_ME3	83	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A28_ME3	84	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A29_ME3	85	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A30_ME3	86	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_A31_ME3	87	/* ME_THREAD_A */
-#define IRQ_IXP23XX_ME_THREAD_B0_ME0	88	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B1_ME0	89	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B2_ME0	90	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B3_ME0	91	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B4_ME0	92	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B5_ME0	93	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B6_ME0	94	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B7_ME0	95	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B8_ME1	96	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B9_ME1	97	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B10_ME1	98	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B11_ME1	99	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B12_ME1	100	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B13_ME1	101	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B14_ME1	102	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B15_ME1	103	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B16_ME2	104	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B17_ME2	105	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B18_ME2	106	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B19_ME2	107	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B20_ME2	108	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B21_ME2	109	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B22_ME2	110	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B23_ME2	111	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B24_ME3	112	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B25_ME3	113	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B26_ME3	114	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B27_ME3	115	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B28_ME3	116	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B29_ME3	117	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B30_ME3	118	/* ME_THREAD_B */
-#define IRQ_IXP23XX_ME_THREAD_B31_ME3	119	/* ME_THREAD_B */
-
-#define NUM_IXP23XX_RAW_IRQS		120
-
-#define IRQ_IXP23XX_INTA		120	/* Indirect pcxg_pci_int_rph */
-#define IRQ_IXP23XX_INTB		121	/* Indirect pcxg_pci_int_rph */
-
-#define NR_IXP23XX_IRQ			(IRQ_IXP23XX_INTB + 1)
-
-/*
- * We default to 32 per-board IRQs. Increase this number if you need
- * more, but keep it realistic.
- */
-#define NR_IXP23XX_MACH_IRQS 		32
-
-#define NR_IRQS				(NR_IXP23XX_IRQS + NR_IXP23XX_MACH_IRQS)
-
-#define IXP23XX_MACH_IRQ(irq) 		(NR_IXP23XX_IRQ + (irq))
-
-
-/*
- * IXDP2351-specific interrupts
- */
-
-/*
- * External PCI interrupts signaled through INTB
- *
- */
-#define IXDP2351_INTB_IRQ_BASE 		0
-#define IRQ_IXDP2351_INTA_82546		IXP23XX_MACH_IRQ(0)
-#define IRQ_IXDP2351_INTB_82546		IXP23XX_MACH_IRQ(1)
-#define IRQ_IXDP2351_SPCI_DB_0		IXP23XX_MACH_IRQ(2)
-#define IRQ_IXDP2351_SPCI_DB_1		IXP23XX_MACH_IRQ(3)
-#define IRQ_IXDP2351_SPCI_PMC_INTA	IXP23XX_MACH_IRQ(4)
-#define IRQ_IXDP2351_SPCI_PMC_INTB	IXP23XX_MACH_IRQ(5)
-#define IRQ_IXDP2351_SPCI_PMC_INTC	IXP23XX_MACH_IRQ(6)
-#define IRQ_IXDP2351_SPCI_PMC_INTD	IXP23XX_MACH_IRQ(7)
-#define IRQ_IXDP2351_SPCI_FIC		IXP23XX_MACH_IRQ(8)
-
-#define IXDP2351_INTB_IRQ_BIT(irq)	(irq - IXP23XX_MACH_IRQ(0))
-#define IXDP2351_INTB_IRQ_MASK(irq)	(1 << IXDP2351_INTB_IRQ_BIT(irq))
-#define IXDP2351_INTB_IRQ_VALID		0x01FF
-#define IXDP2351_INTB_IRQ_NUM 		16
-
-/*
- * Other external interrupts signaled through INTA
- */
-#define IXDP2351_INTA_IRQ_BASE 		16
-#define IRQ_IXDP2351_IPMI_FROM		IXP23XX_MACH_IRQ(16)
-#define IRQ_IXDP2351_125US		IXP23XX_MACH_IRQ(17)
-#define IRQ_IXDP2351_DB_0_ADD		IXP23XX_MACH_IRQ(18)
-#define IRQ_IXDP2351_DB_1_ADD		IXP23XX_MACH_IRQ(19)
-#define IRQ_IXDP2351_DEBUG1		IXP23XX_MACH_IRQ(20)
-#define IRQ_IXDP2351_ADD_UART		IXP23XX_MACH_IRQ(21)
-#define IRQ_IXDP2351_FIC_ADD		IXP23XX_MACH_IRQ(24)
-#define IRQ_IXDP2351_CS8900		IXP23XX_MACH_IRQ(25)
-#define IRQ_IXDP2351_BBSRAM		IXP23XX_MACH_IRQ(26)
-#define IRQ_IXDP2351_CONFIG_MEDIA	IXP23XX_MACH_IRQ(27)
-#define IRQ_IXDP2351_CLOCK_REF		IXP23XX_MACH_IRQ(28)
-#define IRQ_IXDP2351_A10_NP		IXP23XX_MACH_IRQ(29)
-#define IRQ_IXDP2351_A11_NP		IXP23XX_MACH_IRQ(30)
-#define IRQ_IXDP2351_DEBUG_NP		IXP23XX_MACH_IRQ(31)
-
-#define IXDP2351_INTA_IRQ_BIT(irq) 	(irq - IXP23XX_MACH_IRQ(16))
-#define IXDP2351_INTA_IRQ_MASK(irq) 	(1 << IXDP2351_INTA_IRQ_BIT(irq))
-#define IXDP2351_INTA_IRQ_VALID 	0xFF3F
-#define IXDP2351_INTA_IRQ_NUM 		16
-
-
-/*
- * ADI RoadRunner IRQs
- */
-#define IRQ_ROADRUNNER_PCI_INTA 	IRQ_IXP23XX_INTA
-#define IRQ_ROADRUNNER_PCI_INTB 	IRQ_IXP23XX_INTB
-#define IRQ_ROADRUNNER_PCI_INTC 	IRQ_IXP23XX_GPIO11
-#define IRQ_ROADRUNNER_PCI_INTD 	IRQ_IXP23XX_GPIO12
-
-/*
- * Put new board definitions here
- */
-
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/include/mach/ixdp2351.h b/arch/arm/mach-ixp23xx/include/mach/ixdp2351.h
deleted file mode 100644
index 6639510..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/ixdp2351.h
+++ /dev/null
@@ -1,89 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/ixdp2351.h
- *
- * Register and other defines for IXDP2351
- *
- * Copyright (c) 2002-2004 Intel Corp.
- * Copytight (c) 2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __ASM_ARCH_IXDP2351_H
-#define __ASM_ARCH_IXDP2351_H
-
-/*
- * NP module memory map
- */
-#define IXDP2351_NP_PHYS_BASE		(IXP23XX_EXP_BUS_CS4_BASE)
-#define IXDP2351_NP_PHYS_SIZE		0x00100000
-#define IXDP2351_NP_VIRT_BASE		0xeff00000
-
-#define IXDP2351_VIRT_CS8900_BASE	(IXDP2351_NP_VIRT_BASE)
-#define IXDP2351_VIRT_CS8900_END	(IXDP2351_VIRT_CS8900_BASE + 16)
-
-#define IXDP2351_VIRT_NP_CPLD_BASE 	(IXP23XX_EXP_BUS_CS4_BASE_VIRT + 0x00010000)
-
-#define IXDP2351_NP_CPLD_REG(reg) ((volatile u16 *)(IXDP2351_VIRT_NP_CPLD_BASE + reg))
-
-#define IXDP2351_NP_CPLD_RESET1_REG	IXDP2351_NP_CPLD_REG(0x00)
-#define IXDP2351_NP_CPLD_LED_REG	IXDP2351_NP_CPLD_REG(0x02)
-#define IXDP2351_NP_CPLD_VERSION_REG	IXDP2351_NP_CPLD_REG(0x04)
-
-/*
- * Base board module memory map
- */
-
-#define IXDP2351_BB_BASE_PHYS		(IXP23XX_EXP_BUS_CS5_BASE)
-#define IXDP2351_BB_SIZE		0x01000000
-#define IXDP2351_BB_BASE_VIRT		(0xee000000)
-
-#define IXDP2351_BB_AREA_BASE(offset)	(IXDP2351_BB_BASE_VIRT + offset)
-
-#define IXDP2351_VIRT_NVRAM_BASE	IXDP2351_BB_AREA_BASE(0x0)
-#define IXDP2351_NVRAM_SIZE		(0x20000)
-
-#define IXDP2351_VIRT_MB_IXF1104_BASE	IXDP2351_BB_AREA_BASE(0x00020000)
-#define IXDP2351_VIRT_ADD_UART_BASE	IXDP2351_BB_AREA_BASE(0x000240C0)
-#define IXDP2351_VIRT_FIC_BASE		IXDP2351_BB_AREA_BASE(0x00200000)
-#define IXDP2351_VIRT_DB0_BASE		IXDP2351_BB_AREA_BASE(0x00400000)
-#define IXDP2351_VIRT_DB1_BASE		IXDP2351_BB_AREA_BASE(0x00600000)
-#define IXDP2351_VIRT_CPLD_BASE		IXDP2351_BB_AREA_BASE(0x00024000)
-
-/*
- * On board CPLD registers
- */
-#define IXDP2351_CPLD_BB_REG(reg) ((volatile u16 *)(IXDP2351_VIRT_CPLD_BASE + reg))
-
-#define IXDP2351_CPLD_RESET0_REG	IXDP2351_CPLD_BB_REG(0x00)
-#define IXDP2351_CPLD_RESET1_REG	IXDP2351_CPLD_BB_REG(0x04)
-
-#define IXDP2351_CPLD_RESET1_MAGIC 	0x55AA
-#define IXDP2351_CPLD_RESET1_ENABLE 	0x8000
-
-#define IXDP2351_CPLD_FPGA_CONFIG_REG	IXDP2351_CPLD_BB_REG(0x08)
-#define IXDP2351_CPLD_INTB_MASK_SET_REG	IXDP2351_CPLD_BB_REG(0x10)
-#define IXDP2351_CPLD_INTA_MASK_SET_REG	IXDP2351_CPLD_BB_REG(0x14)
-#define IXDP2351_CPLD_INTB_STAT_REG	IXDP2351_CPLD_BB_REG(0x18)
-#define IXDP2351_CPLD_INTA_STAT_REG	IXDP2351_CPLD_BB_REG(0x1C)
-#define IXDP2351_CPLD_INTB_RAW_REG	IXDP2351_CPLD_BB_REG(0x20)	/* read */
-#define IXDP2351_CPLD_INTA_RAW_REG	IXDP2351_CPLD_BB_REG(0x24)	/* read */
-#define IXDP2351_CPLD_INTB_MASK_CLR_REG	IXDP2351_CPLD_INTB_RAW_REG	/* write */
-#define IXDP2351_CPLD_INTA_MASK_CLR_REG	IXDP2351_CPLD_INTA_RAW_REG	/* write */
-#define IXDP2351_CPLD_INTB_SIM_REG	IXDP2351_CPLD_BB_REG(0x28)
-#define IXDP2351_CPLD_INTA_SIM_REG	IXDP2351_CPLD_BB_REG(0x2C)
-	/* Interrupt bits are defined in irqs.h */
-#define IXDP2351_CPLD_BB_GBE0_REG	IXDP2351_CPLD_BB_REG(0x30)
-#define IXDP2351_CPLD_BB_GBE1_REG	IXDP2351_CPLD_BB_REG(0x34)
-
-/* #define IXDP2351_CPLD_BB_MISC_REG	IXDP2351_CPLD_REG(0x1C) */
-/* #define IXDP2351_CPLD_BB_MISC_REV_MASK	0xFF		*/
-/* #define IXDP2351_CPLD_BB_GDXCS0_REG	IXDP2351_CPLD_REG(0x24) */
-/* #define IXDP2351_CPLD_BB_GDXCS1_REG	IXDP2351_CPLD_REG(0x28) */
-/* #define IXDP2351_CPLD_BB_CLOCK_REG	IXDP2351_CPLD_REG(0x04) */
-
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/include/mach/ixp23xx.h b/arch/arm/mach-ixp23xx/include/mach/ixp23xx.h
deleted file mode 100644
index 6d02481..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/ixp23xx.h
+++ /dev/null
@@ -1,298 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/ixp23xx.h
- *
- * Register definitions for IXP23XX
- *
- * Copyright (C) 2003-2005 Intel Corporation.
- * Copyright (C) 2005 MontaVista Software, Inc.
- *
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_IXP23XX_H
-#define __ASM_ARCH_IXP23XX_H
-
-/*
- * IXP2300 linux memory map:
- *
- * virt		phys		size
- * fffd0000	a0000000	64K		XSI2CPP_CSR
- * fffc0000	c4000000	4K		EXP_CFG
- * fff00000	c8000000	64K		PERIPHERAL
- * fe000000	1c0000000	16M		CAP_CSR
- * fd000000	1c8000000	16M		MSF_CSR
- * fb000000			16M		---
- * fa000000	1d8000000	32M		PCI_IO
- * f8000000	1da000000	32M		PCI_CFG
- * f6000000	1de000000	32M		PCI_CREG
- * f4000000			32M		---
- * f0000000	1e0000000	64M		PCI_MEM
- * e[c-f]000000					per-platform mappings
- */
-
-
-/****************************************************************************
- * Static mappings.
- ****************************************************************************/
-#define IXP23XX_XSI2CPP_CSR_PHYS	0xa0000000
-#define IXP23XX_XSI2CPP_CSR_VIRT	0xfffd0000
-#define IXP23XX_XSI2CPP_CSR_SIZE	0x00010000
-
-#define IXP23XX_EXP_CFG_PHYS		0xc4000000
-#define IXP23XX_EXP_CFG_VIRT		0xfffc0000
-#define IXP23XX_EXP_CFG_SIZE		0x00001000
-
-#define IXP23XX_PERIPHERAL_PHYS		0xc8000000
-#define IXP23XX_PERIPHERAL_VIRT		0xfff00000
-#define IXP23XX_PERIPHERAL_SIZE		0x00010000
-
-#define IXP23XX_CAP_CSR_PHYS		0x1c0000000ULL
-#define IXP23XX_CAP_CSR_VIRT		0xfe000000
-#define IXP23XX_CAP_CSR_SIZE		0x01000000
-
-#define IXP23XX_MSF_CSR_PHYS		0x1c8000000ULL
-#define IXP23XX_MSF_CSR_VIRT		0xfd000000
-#define IXP23XX_MSF_CSR_SIZE		0x01000000
-
-#define IXP23XX_PCI_IO_PHYS		0x1d8000000ULL
-#define IXP23XX_PCI_IO_VIRT		0xfa000000
-#define IXP23XX_PCI_IO_SIZE		0x02000000
-
-#define IXP23XX_PCI_CFG_PHYS		0x1da000000ULL
-#define IXP23XX_PCI_CFG_VIRT		0xf8000000
-#define IXP23XX_PCI_CFG_SIZE		0x02000000
-#define IXP23XX_PCI_CFG0_VIRT		IXP23XX_PCI_CFG_VIRT
-#define IXP23XX_PCI_CFG1_VIRT		(IXP23XX_PCI_CFG_VIRT + 0x01000000)
-
-#define IXP23XX_PCI_CREG_PHYS		0x1de000000ULL
-#define IXP23XX_PCI_CREG_VIRT		0xf6000000
-#define IXP23XX_PCI_CREG_SIZE		0x02000000
-#define IXP23XX_PCI_CSR_VIRT		(IXP23XX_PCI_CREG_VIRT + 0x01000000)
-
-#define IXP23XX_PCI_MEM_START		0xe0000000
-#define IXP23XX_PCI_MEM_PHYS		0x1e0000000ULL
-#define IXP23XX_PCI_MEM_VIRT		0xf0000000
-#define IXP23XX_PCI_MEM_SIZE		0x04000000
-
-
-/****************************************************************************
- * XSI2CPP CSRs.
- ****************************************************************************/
-#define IXP23XX_XSI2CPP_REG(x)		((volatile unsigned long *)(IXP23XX_XSI2CPP_CSR_VIRT + (x)))
-#define IXP23XX_CPP2XSI_CURR_XFER_REG3	IXP23XX_XSI2CPP_REG(0xf8)
-#define IXP23XX_CPP2XSI_ADDR_31		(1 << 19)
-#define IXP23XX_CPP2XSI_PSH_OFF		(1 << 20)
-#define IXP23XX_CPP2XSI_COH_OFF		(1 << 21)
-
-
-/****************************************************************************
- * Expansion Bus Config.
- ****************************************************************************/
-#define IXP23XX_EXP_CFG_REG(x)		((volatile unsigned long *)(IXP23XX_EXP_CFG_VIRT + (x)))
-#define IXP23XX_EXP_CS0			IXP23XX_EXP_CFG_REG(0x00)
-#define IXP23XX_EXP_CS1			IXP23XX_EXP_CFG_REG(0x04)
-#define IXP23XX_EXP_CS2			IXP23XX_EXP_CFG_REG(0x08)
-#define IXP23XX_EXP_CS3			IXP23XX_EXP_CFG_REG(0x0c)
-#define IXP23XX_EXP_CS4			IXP23XX_EXP_CFG_REG(0x10)
-#define IXP23XX_EXP_CS5			IXP23XX_EXP_CFG_REG(0x14)
-#define IXP23XX_EXP_CS6			IXP23XX_EXP_CFG_REG(0x18)
-#define IXP23XX_EXP_CS7			IXP23XX_EXP_CFG_REG(0x1c)
-#define IXP23XX_FLASH_WRITABLE		(0x2)
-#define IXP23XX_FLASH_BUS8		(0x1)
-
-#define IXP23XX_EXP_CFG0		IXP23XX_EXP_CFG_REG(0x20)
-#define IXP23XX_EXP_CFG1		IXP23XX_EXP_CFG_REG(0x24)
-#define IXP23XX_EXP_CFG0_MEM_MAP		(1 << 31)
-#define IXP23XX_EXP_CFG0_XSCALE_SPEED_SEL 	(3 << 22)
-#define IXP23XX_EXP_CFG0_XSCALE_SPEED_EN	(1 << 21)
-#define IXP23XX_EXP_CFG0_CPP_SPEED_SEL		(3 << 19)
-#define IXP23XX_EXP_CFG0_CPP_SPEED_EN		(1 << 18)
-#define IXP23XX_EXP_CFG0_PCI_SWIN		(3 << 16)
-#define IXP23XX_EXP_CFG0_PCI_DWIN		(3 << 14)
-#define IXP23XX_EXP_CFG0_PCI33_MODE		(1 << 13)
-#define IXP23XX_EXP_CFG0_QDR_SPEED_SEL		(1 << 12)
-#define IXP23XX_EXP_CFG0_CPP_DIV_SEL		(1 << 5)
-#define IXP23XX_EXP_CFG0_XSI_NOT_PRES		(1 << 4)
-#define IXP23XX_EXP_CFG0_PROM_BOOT		(1 << 3)
-#define IXP23XX_EXP_CFG0_PCI_ARB		(1 << 2)
-#define IXP23XX_EXP_CFG0_PCI_HOST		(1 << 1)
-#define IXP23XX_EXP_CFG0_FLASH_WIDTH		(1 << 0)
-
-#define IXP23XX_EXP_UNIT_FUSE		IXP23XX_EXP_CFG_REG(0x28)
-#define IXP23XX_EXP_MSF_MUX		IXP23XX_EXP_CFG_REG(0x30)
-#define IXP23XX_EXP_CFG_FUSE		IXP23XX_EXP_CFG_REG(0x34)
-
-#define IXP23XX_EXP_BUS_PHYS		0x90000000
-#define IXP23XX_EXP_BUS_WINDOW_SIZE	0x01000000
-
-#define IXP23XX_EXP_BUS_CS0_BASE	(IXP23XX_EXP_BUS_PHYS + 0x00000000)
-#define IXP23XX_EXP_BUS_CS1_BASE	(IXP23XX_EXP_BUS_PHYS + 0x01000000)
-#define IXP23XX_EXP_BUS_CS2_BASE	(IXP23XX_EXP_BUS_PHYS + 0x02000000)
-#define IXP23XX_EXP_BUS_CS3_BASE	(IXP23XX_EXP_BUS_PHYS + 0x03000000)
-#define IXP23XX_EXP_BUS_CS4_BASE	(IXP23XX_EXP_BUS_PHYS + 0x04000000)
-#define IXP23XX_EXP_BUS_CS5_BASE	(IXP23XX_EXP_BUS_PHYS + 0x05000000)
-#define IXP23XX_EXP_BUS_CS6_BASE	(IXP23XX_EXP_BUS_PHYS + 0x06000000)
-#define IXP23XX_EXP_BUS_CS7_BASE	(IXP23XX_EXP_BUS_PHYS + 0x07000000)
-
-
-/****************************************************************************
- * Peripherals.
- ****************************************************************************/
-#define IXP23XX_UART1_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x0000)
-#define IXP23XX_UART2_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x1000)
-#define IXP23XX_PMU_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x2000)
-#define IXP23XX_INTC_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x3000)
-#define IXP23XX_GPIO_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x4000)
-#define IXP23XX_TIMER_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x5000)
-#define IXP23XX_NPE0_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x6000)
-#define IXP23XX_DSR_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x7000)
-#define IXP23XX_NPE1_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x8000)
-#define IXP23XX_ETH0_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0x9000)
-#define IXP23XX_ETH1_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0xA000)
-#define IXP23XX_GIG0_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0xB000)
-#define IXP23XX_GIG1_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0xC000)
-#define IXP23XX_DDRS_VIRT		(IXP23XX_PERIPHERAL_VIRT + 0xD000)
-
-#define IXP23XX_UART1_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x0000)
-#define IXP23XX_UART2_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x1000)
-#define IXP23XX_PMU_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x2000)
-#define IXP23XX_INTC_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x3000)
-#define IXP23XX_GPIO_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x4000)
-#define IXP23XX_TIMER_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x5000)
-#define IXP23XX_NPE0_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x6000)
-#define IXP23XX_DSR_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x7000)
-#define IXP23XX_NPE1_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x8000)
-#define IXP23XX_ETH0_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0x9000)
-#define IXP23XX_ETH1_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0xA000)
-#define IXP23XX_GIG0_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0xB000)
-#define IXP23XX_GIG1_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0xC000)
-#define IXP23XX_DDRS_PHYS		(IXP23XX_PERIPHERAL_PHYS + 0xD000)
-
-
-/****************************************************************************
- * Interrupt controller.
- ****************************************************************************/
-#define IXP23XX_INTC_REG(x)		 ((volatile unsigned long *)(IXP23XX_INTC_VIRT + (x)))
-#define IXP23XX_INTR_ST1		IXP23XX_INTC_REG(0x00)
-#define IXP23XX_INTR_ST2		IXP23XX_INTC_REG(0x04)
-#define IXP23XX_INTR_ST3		IXP23XX_INTC_REG(0x08)
-#define IXP23XX_INTR_ST4		IXP23XX_INTC_REG(0x0c)
-#define IXP23XX_INTR_EN1		IXP23XX_INTC_REG(0x10)
-#define IXP23XX_INTR_EN2		IXP23XX_INTC_REG(0x14)
-#define IXP23XX_INTR_EN3		IXP23XX_INTC_REG(0x18)
-#define IXP23XX_INTR_EN4		IXP23XX_INTC_REG(0x1c)
-#define IXP23XX_INTR_SEL1		IXP23XX_INTC_REG(0x20)
-#define IXP23XX_INTR_SEL2		IXP23XX_INTC_REG(0x24)
-#define IXP23XX_INTR_SEL3		IXP23XX_INTC_REG(0x28)
-#define IXP23XX_INTR_SEL4		IXP23XX_INTC_REG(0x2c)
-#define IXP23XX_INTR_IRQ_ST1		IXP23XX_INTC_REG(0x30)
-#define IXP23XX_INTR_IRQ_ST2		IXP23XX_INTC_REG(0x34)
-#define IXP23XX_INTR_IRQ_ST3		IXP23XX_INTC_REG(0x38)
-#define IXP23XX_INTR_IRQ_ST4		IXP23XX_INTC_REG(0x3c)
-#define IXP23XX_INTR_IRQ_ENC_ST_OFFSET	0x54
-
-
-/****************************************************************************
- * GPIO.
- ****************************************************************************/
-#define IXP23XX_GPIO_REG(x)		((volatile unsigned long *)(IXP23XX_GPIO_VIRT + (x)))
-#define IXP23XX_GPIO_GPOUTR		IXP23XX_GPIO_REG(0x00)
-#define IXP23XX_GPIO_GPOER		IXP23XX_GPIO_REG(0x04)
-#define IXP23XX_GPIO_GPINR		IXP23XX_GPIO_REG(0x08)
-#define IXP23XX_GPIO_GPISR		IXP23XX_GPIO_REG(0x0c)
-#define IXP23XX_GPIO_GPIT1R		IXP23XX_GPIO_REG(0x10)
-#define IXP23XX_GPIO_GPIT2R		IXP23XX_GPIO_REG(0x14)
-#define IXP23XX_GPIO_GPCLKR		IXP23XX_GPIO_REG(0x18)
-#define IXP23XX_GPIO_GPDBSELR 		IXP23XX_GPIO_REG(0x1c)
-
-#define IXP23XX_GPIO_STYLE_MASK		0x7
-#define IXP23XX_GPIO_STYLE_ACTIVE_HIGH	0x0
-#define IXP23XX_GPIO_STYLE_ACTIVE_LOW	0x1
-#define IXP23XX_GPIO_STYLE_RISING_EDGE	0x2
-#define IXP23XX_GPIO_STYLE_FALLING_EDGE	0x3
-#define IXP23XX_GPIO_STYLE_TRANSITIONAL	0x4
-
-#define IXP23XX_GPIO_STYLE_SIZE		3
-
-
-/****************************************************************************
- * Timer.
- ****************************************************************************/
-#define IXP23XX_TIMER_REG(x)		((volatile unsigned long *)(IXP23XX_TIMER_VIRT + (x)))
-#define IXP23XX_TIMER_CONT		IXP23XX_TIMER_REG(0x00)
-#define IXP23XX_TIMER1_TIMESTAMP	IXP23XX_TIMER_REG(0x04)
-#define IXP23XX_TIMER1_RELOAD		IXP23XX_TIMER_REG(0x08)
-#define IXP23XX_TIMER2_TIMESTAMP	IXP23XX_TIMER_REG(0x0c)
-#define IXP23XX_TIMER2_RELOAD		IXP23XX_TIMER_REG(0x10)
-#define IXP23XX_TIMER_WDOG		IXP23XX_TIMER_REG(0x14)
-#define IXP23XX_TIMER_WDOG_EN		IXP23XX_TIMER_REG(0x18)
-#define IXP23XX_TIMER_WDOG_KEY		IXP23XX_TIMER_REG(0x1c)
-#define IXP23XX_TIMER_WDOG_KEY_MAGIC	0x482e
-#define IXP23XX_TIMER_STATUS		IXP23XX_TIMER_REG(0x20)
-#define IXP23XX_TIMER_SOFT_RESET	IXP23XX_TIMER_REG(0x24)
-#define IXP23XX_TIMER_SOFT_RESET_EN	IXP23XX_TIMER_REG(0x28)
-
-#define IXP23XX_TIMER_ENABLE		(1 << 0)
-#define IXP23XX_TIMER_ONE_SHOT		(1 << 1)
-/* Low order bits of reload value ignored */
-#define IXP23XX_TIMER_RELOAD_MASK	(0x3)
-#define IXP23XX_TIMER_DISABLED		(0x0)
-#define IXP23XX_TIMER1_INT_PEND		(1 << 0)
-#define IXP23XX_TIMER2_INT_PEND		(1 << 1)
-#define IXP23XX_TIMER_STATUS_TS_PEND	(1 << 2)
-#define IXP23XX_TIMER_STATUS_WDOG_PEND	(1 << 3)
-#define IXP23XX_TIMER_STATUS_WARM_RESET	(1 << 4)
-
-
-/****************************************************************************
- * CAP CSRs.
- ****************************************************************************/
-#define IXP23XX_GLOBAL_REG(x)		((volatile unsigned long *)(IXP23XX_CAP_CSR_VIRT + 0x4a00 + (x)))
-#define IXP23XX_PRODUCT_ID		IXP23XX_GLOBAL_REG(0x00)
-#define IXP23XX_MISC_CONTROL		IXP23XX_GLOBAL_REG(0x04)
-#define IXP23XX_MSF_CLK_CNTRL		IXP23XX_GLOBAL_REG(0x08)
-#define IXP23XX_RESET0			IXP23XX_GLOBAL_REG(0x0c)
-#define IXP23XX_RESET1			IXP23XX_GLOBAL_REG(0x10)
-#define IXP23XX_STRAP_OPTIONS		IXP23XX_GLOBAL_REG(0x18)
-
-#define IXP23XX_ENABLE_WATCHDOG		(1 << 24)
-#define IXP23XX_SHPC_INIT_COMP		(1 << 21)
-#define IXP23XX_RST_ALL			(1 << 16)
-#define IXP23XX_RESET_PCI		(1 << 2)
-#define IXP23XX_PCI_UNIT_RESET		(1 << 1)
-#define IXP23XX_XSCALE_RESET		(1 << 0)
-
-#define IXP23XX_UENGINE_CSR_VIRT_BASE	(IXP23XX_CAP_CSR_VIRT + 0x18000)
-
-
-/****************************************************************************
- * PCI CSRs.
- ****************************************************************************/
-#define IXP23XX_PCI_CREG(x)		((volatile unsigned long *)(IXP23XX_PCI_CREG_VIRT + (x)))
-#define IXP23XX_PCI_CMDSTAT		IXP23XX_PCI_CREG(0x04)
-#define IXP23XX_PCI_SRAM_BAR		IXP23XX_PCI_CREG(0x14)
-#define IXP23XX_PCI_SDRAM_BAR		IXP23XX_PCI_CREG(0x18)
-
-
-#define IXP23XX_PCI_CSR(x)		((volatile unsigned long *)(IXP23XX_PCI_CREG_VIRT + 0x01000000 + (x)))
-#define IXP23XX_PCI_OUT_INT_STATUS	IXP23XX_PCI_CSR(0x0030)
-#define IXP23XX_PCI_OUT_INT_MASK	IXP23XX_PCI_CSR(0x0034)
-#define IXP23XX_PCI_SRAM_BASE_ADDR_MASK IXP23XX_PCI_CSR(0x00fc)
-#define IXP23XX_PCI_DRAM_BASE_ADDR_MASK IXP23XX_PCI_CSR(0x0100)
-#define IXP23XX_PCI_CONTROL		IXP23XX_PCI_CSR(0x013c)
-#define IXP23XX_PCI_ADDR_EXT		IXP23XX_PCI_CSR(0x0140)
-#define IXP23XX_PCI_ME_PUSH_STATUS	IXP23XX_PCI_CSR(0x0148)
-#define IXP23XX_PCI_ME_PUSH_EN		IXP23XX_PCI_CSR(0x014c)
-#define IXP23XX_PCI_ERR_STATUS		IXP23XX_PCI_CSR(0x0150)
-#define IXP23XX_PCI_ERROR_STATUS	IXP23XX_PCI_CSR(0x0150)
-#define IXP23XX_PCI_ERR_ENABLE		IXP23XX_PCI_CSR(0x0154)
-#define IXP23XX_PCI_XSCALE_INT_STATUS	IXP23XX_PCI_CSR(0x0158)
-#define IXP23XX_PCI_XSCALE_INT_ENABLE	IXP23XX_PCI_CSR(0x015c)
-#define IXP23XX_PCI_CPP_ADDR_BITS	IXP23XX_PCI_CSR(0x0160)
-
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/include/mach/memory.h b/arch/arm/mach-ixp23xx/include/mach/memory.h
deleted file mode 100644
index 6cf0704..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/memory.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/memory.h
- *
- * Copyright (c) 2003-2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#include <mach/hardware.h>
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET		(0x00000000)
-
-#define IXP23XX_PCI_SDRAM_OFFSET (*((volatile int *)IXP23XX_PCI_SDRAM_BAR) & 0xfffffff0)
-
-#define __phys_to_bus(x)	((x) + (IXP23XX_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-#define __bus_to_phys(x)	((x) - (IXP23XX_PCI_SDRAM_OFFSET - PHYS_OFFSET))
-
-#define __virt_to_bus(v)	__phys_to_bus(__virt_to_phys(v))
-#define __bus_to_virt(b)	__phys_to_virt(__bus_to_phys(b))
-#define __pfn_to_bus(p)		__phys_to_bus(__pfn_to_phys(p))
-#define __bus_to_pfn(b)		__phys_to_pfn(__bus_to_phys(b))
-
-#define arch_is_coherent()	1
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/include/mach/platform.h b/arch/arm/mach-ixp23xx/include/mach/platform.h
deleted file mode 100644
index 50de558..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/platform.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/platform.h
- *
- * Various bits of code used by platform-level code.
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASSEMBLY__
-
-static inline unsigned long ixp2000_reg_read(volatile void *reg)
-{
-	return *((volatile unsigned long *)reg);
-}
-
-static inline void ixp2000_reg_write(volatile void *reg, unsigned long val)
-{
-	*((volatile unsigned long *)reg) = val;
-}
-
-static inline void ixp2000_reg_wrb(volatile void *reg, unsigned long val)
-{
-	*((volatile unsigned long *)reg) = val;
-}
-
-struct pci_sys_data;
-
-void ixp23xx_map_io(void);
-void ixp23xx_init_irq(void);
-void ixp23xx_sys_init(void);
-void ixp23xx_restart(char, const char *);
-int ixp23xx_pci_setup(int, struct pci_sys_data *);
-void ixp23xx_pci_preinit(void);
-struct pci_bus *ixp23xx_pci_scan_bus(int, struct pci_sys_data*);
-void ixp23xx_pci_slave_init(void);
-
-extern struct sys_timer ixp23xx_timer;
-
-#define IXP23XX_UART_XTAL		14745600
-
-#ifndef __ASSEMBLY__
-/*
- * Is system memory on the XSI or CPP bus?
- */
-static inline unsigned ixp23xx_cpp_boot(void)
-{
-	return (*IXP23XX_EXP_CFG0 & IXP23XX_EXP_CFG0_XSI_NOT_PRES);
-}
-#endif
-
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/include/mach/time.h b/arch/arm/mach-ixp23xx/include/mach/time.h
deleted file mode 100644
index b61dafc..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/time.h
+++ /dev/null
@@ -1,3 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/time.h
- */
diff --git a/arch/arm/mach-ixp23xx/include/mach/timex.h b/arch/arm/mach-ixp23xx/include/mach/timex.h
deleted file mode 100644
index e341e9c..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/timex.h
+++ /dev/null
@@ -1,7 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/timex.h
- *
- * XScale architecture timex specifications
- */
-
-#define CLOCK_TICK_RATE 75000000
diff --git a/arch/arm/mach-ixp23xx/include/mach/uncompress.h b/arch/arm/mach-ixp23xx/include/mach/uncompress.h
deleted file mode 100644
index 8b4c358..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/uncompress.h
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/uncompress.h
- *
- * Copyright (C) 2002-2004 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_UNCOMPRESS_H
-#define __ASM_ARCH_UNCOMPRESS_H
-
-#include <mach/ixp23xx.h>
-#include <linux/serial_reg.h>
-
-#define UART_BASE	((volatile u32 *)IXP23XX_UART1_PHYS)
-
-static inline void putc(char c)
-{
-	int j;
-
-	for (j = 0; j < 0x1000; j++) {
-		if (UART_BASE[UART_LSR] & UART_LSR_THRE)
-			break;
-		barrier();
-	}
-
-	UART_BASE[UART_TX] = c;
-}
-
-static inline void flush(void)
-{
-}
-
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
-
-
-#endif
diff --git a/arch/arm/mach-ixp23xx/ixdp2351.c b/arch/arm/mach-ixp23xx/ixdp2351.c
deleted file mode 100644
index b0e07db..0000000
--- a/arch/arm/mach-ixp23xx/ixdp2351.c
+++ /dev/null
@@ -1,347 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/ixdp2351.c
- *
- * IXDP2351 board-specific routines
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * Based on 2.4 code Copyright 2004 (c) Intel Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/ioport.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/pci.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-
-/*
- * IXDP2351 Interrupt Handling
- */
-static void ixdp2351_inta_mask(struct irq_data *d)
-{
-	*IXDP2351_CPLD_INTA_MASK_SET_REG = IXDP2351_INTA_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_inta_unmask(struct irq_data *d)
-{
-	*IXDP2351_CPLD_INTA_MASK_CLR_REG = IXDP2351_INTA_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_inta_handler(unsigned int irq, struct irq_desc *desc)
-{
-	u16 ex_interrupt =
-		*IXDP2351_CPLD_INTA_STAT_REG & IXDP2351_INTA_IRQ_VALID;
-	int i;
-
-	desc->irq_data.chip->irq_mask(&desc->irq_data);
-
-	for (i = 0; i < IXDP2351_INTA_IRQ_NUM; i++) {
-		if (ex_interrupt & (1 << i)) {
-			int cpld_irq =
-				IXP23XX_MACH_IRQ(IXDP2351_INTA_IRQ_BASE + i);
-			generic_handle_irq(cpld_irq);
-		}
-	}
-
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2351_inta_chip = {
-	.irq_ack	= ixdp2351_inta_mask,
-	.irq_mask	= ixdp2351_inta_mask,
-	.irq_unmask	= ixdp2351_inta_unmask
-};
-
-static void ixdp2351_intb_mask(struct irq_data *d)
-{
-	*IXDP2351_CPLD_INTB_MASK_SET_REG = IXDP2351_INTB_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_intb_unmask(struct irq_data *d)
-{
-	*IXDP2351_CPLD_INTB_MASK_CLR_REG = IXDP2351_INTB_IRQ_MASK(d->irq);
-}
-
-static void ixdp2351_intb_handler(unsigned int irq, struct irq_desc *desc)
-{
-	u16 ex_interrupt =
-		*IXDP2351_CPLD_INTB_STAT_REG & IXDP2351_INTB_IRQ_VALID;
-	int i;
-
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-
-	for (i = 0; i < IXDP2351_INTB_IRQ_NUM; i++) {
-		if (ex_interrupt & (1 << i)) {
-			int cpld_irq =
-				IXP23XX_MACH_IRQ(IXDP2351_INTB_IRQ_BASE + i);
-			generic_handle_irq(cpld_irq);
-		}
-	}
-
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static struct irq_chip ixdp2351_intb_chip = {
-	.irq_ack	= ixdp2351_intb_mask,
-	.irq_mask	= ixdp2351_intb_mask,
-	.irq_unmask	= ixdp2351_intb_unmask
-};
-
-void __init ixdp2351_init_irq(void)
-{
-	int irq;
-
-	/* Mask all interrupts from CPLD, disable simulation */
-	*IXDP2351_CPLD_INTA_MASK_SET_REG = (u16) -1;
-	*IXDP2351_CPLD_INTB_MASK_SET_REG = (u16) -1;
-	*IXDP2351_CPLD_INTA_SIM_REG = 0;
-	*IXDP2351_CPLD_INTB_SIM_REG = 0;
-
-	ixp23xx_init_irq();
-
-	for (irq = IXP23XX_MACH_IRQ(IXDP2351_INTA_IRQ_BASE);
-	     irq <
-	     IXP23XX_MACH_IRQ(IXDP2351_INTA_IRQ_BASE + IXDP2351_INTA_IRQ_NUM);
-	     irq++) {
-		if (IXDP2351_INTA_IRQ_MASK(irq) & IXDP2351_INTA_IRQ_VALID) {
-			set_irq_flags(irq, IRQF_VALID);
-			irq_set_chip_and_handler(irq, &ixdp2351_inta_chip,
-						 handle_level_irq);
-		}
-	}
-
-	for (irq = IXP23XX_MACH_IRQ(IXDP2351_INTB_IRQ_BASE);
-	     irq <
-	     IXP23XX_MACH_IRQ(IXDP2351_INTB_IRQ_BASE + IXDP2351_INTB_IRQ_NUM);
-	     irq++) {
-		if (IXDP2351_INTB_IRQ_MASK(irq) & IXDP2351_INTB_IRQ_VALID) {
-			set_irq_flags(irq, IRQF_VALID);
-			irq_set_chip_and_handler(irq, &ixdp2351_intb_chip,
-						 handle_level_irq);
-		}
-	}
-
-	irq_set_chained_handler(IRQ_IXP23XX_INTA, ixdp2351_inta_handler);
-	irq_set_chained_handler(IRQ_IXP23XX_INTB, ixdp2351_intb_handler);
-}
-
-/*
- * IXDP2351 PCI
- */
-
-/*
- * This board does not do normal PCI IRQ routing, or any
- * sort of swizzling, so we just need to check where on the
- * bus the device is and figure out what CPLD pin it is
- * being routed to.
- */
-#define DEVPIN(dev, pin) ((pin) | ((dev) << 3))
-
-static int __init ixdp2351_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	u8 bus = dev->bus->number;
-	u32 devpin = DEVPIN(PCI_SLOT(dev->devfn), pin);
-	struct pci_bus *tmp_bus = dev->bus;
-
-	/* Primary bus, no interrupts here */
-	if (!bus)
-		return -1;
-
-	/* Lookup first leaf in bus tree */
-	while ((tmp_bus->parent != NULL) && (tmp_bus->parent->parent != NULL))
-		tmp_bus = tmp_bus->parent;
-
-	/* Select between known bridges */
-	switch (tmp_bus->self->devfn | (tmp_bus->self->bus->number << 8)) {
-		/* Device is located after first bridge */
-	case 0x0008:
-		if (tmp_bus == dev->bus) {
-			/* Device is located directy after first bridge */
-			switch (devpin) {
-				/* Onboard 82546 */
-			case DEVPIN(1, 1):	/* Onboard 82546 ch 0 */
-				return IRQ_IXDP2351_INTA_82546;
-			case DEVPIN(1, 2):	/* Onboard 82546 ch 1 */
-				return IRQ_IXDP2351_INTB_82546;
-				/* PMC SLOT */
-			case DEVPIN(0, 1):	/* PMCP INTA# */
-			case DEVPIN(2, 4):	/* PMCS INTD# */
-				return IRQ_IXDP2351_SPCI_PMC_INTA;
-			case DEVPIN(0, 2):	/* PMCP INTB# */
-			case DEVPIN(2, 1):	/* PMCS INTA# */
-				return IRQ_IXDP2351_SPCI_PMC_INTB;
-			case DEVPIN(0, 3):	/* PMCP INTC# */
-			case DEVPIN(2, 2):	/* PMCS INTB# */
-				return IRQ_IXDP2351_SPCI_PMC_INTC;
-			case DEVPIN(0, 4):	/* PMCP INTD# */
-			case DEVPIN(2, 3):	/* PMCS INTC# */
-				return IRQ_IXDP2351_SPCI_PMC_INTD;
-			}
-		} else {
-			/* Device is located indirectly after first bridge */
-			/* Not supported now */
-			return -1;
-		}
-		break;
-	case 0x0010:
-		if (tmp_bus == dev->bus) {
-			/* Device is located directy after second bridge */
-			/* Secondary bus of second bridge */
-			switch (devpin) {
-			case DEVPIN(0, 1):	/* DB#0 */
-			case DEVPIN(0, 2):
-			case DEVPIN(0, 3):
-			case DEVPIN(0, 4):
-				return IRQ_IXDP2351_SPCI_DB_0;
-			case DEVPIN(1, 1):	/* DB#1 */
-			case DEVPIN(1, 2):
-			case DEVPIN(1, 3):
-			case DEVPIN(1, 4):
-				return IRQ_IXDP2351_SPCI_DB_1;
-			case DEVPIN(2, 1):	/* FIC1 */
-			case DEVPIN(2, 2):
-			case DEVPIN(2, 3):
-			case DEVPIN(2, 4):
-			case DEVPIN(3, 1):	/* FIC2 */
-			case DEVPIN(3, 2):
-			case DEVPIN(3, 3):
-			case DEVPIN(3, 4):
-				return IRQ_IXDP2351_SPCI_FIC;
-			}
-		} else {
-			/* Device is located indirectly after second bridge */
-			/* Not supported now */
-			return -1;
-		}
-		break;
-	}
-
-	return -1;
-}
-
-struct hw_pci ixdp2351_pci __initdata = {
-	.nr_controllers	= 1,
-	.preinit	= ixp23xx_pci_preinit,
-	.setup		= ixp23xx_pci_setup,
-	.scan		= ixp23xx_pci_scan_bus,
-	.map_irq	= ixdp2351_map_irq,
-};
-
-int __init ixdp2351_pci_init(void)
-{
-	if (machine_is_ixdp2351())
-		pci_common_init(&ixdp2351_pci);
-
-	return 0;
-}
-
-subsys_initcall(ixdp2351_pci_init);
-
-/*
- * IXDP2351 Static Mapped I/O
- */
-static struct map_desc ixdp2351_io_desc[] __initdata = {
-	{
-		.virtual	= IXDP2351_NP_VIRT_BASE,
-		.pfn		= __phys_to_pfn((u64)IXDP2351_NP_PHYS_BASE),
-		.length		= IXDP2351_NP_PHYS_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= IXDP2351_BB_BASE_VIRT,
-		.pfn		= __phys_to_pfn((u64)IXDP2351_BB_BASE_PHYS),
-		.length		= IXDP2351_BB_SIZE,
-		.type		= MT_DEVICE
-	}
-};
-
-static void __init ixdp2351_map_io(void)
-{
-	ixp23xx_map_io();
-	iotable_init(ixdp2351_io_desc, ARRAY_SIZE(ixdp2351_io_desc));
-}
-
-static struct physmap_flash_data ixdp2351_flash_data = {
-	.width		= 1,
-};
-
-static struct resource ixdp2351_flash_resource = {
-	.start		= 0x90000000,
-	.end		= 0x93ffffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device ixdp2351_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &ixdp2351_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &ixdp2351_flash_resource,
-};
-
-static void __init ixdp2351_init(void)
-{
-	platform_device_register(&ixdp2351_flash);
-
-	/*
-	 * Mark flash as writeable
-	 */
-	IXP23XX_EXP_CS0[0] |= IXP23XX_FLASH_WRITABLE;
-	IXP23XX_EXP_CS0[1] |= IXP23XX_FLASH_WRITABLE;
-	IXP23XX_EXP_CS0[2] |= IXP23XX_FLASH_WRITABLE;
-	IXP23XX_EXP_CS0[3] |= IXP23XX_FLASH_WRITABLE;
-
-	ixp23xx_sys_init();
-}
-
-static void ixdp2351_restart(char mode, const char *cmd)
-{
-	/* First try machine specific support */
-
-	*IXDP2351_CPLD_RESET1_REG = IXDP2351_CPLD_RESET1_MAGIC;
-	(void) *IXDP2351_CPLD_RESET1_REG;
-	*IXDP2351_CPLD_RESET1_REG = IXDP2351_CPLD_RESET1_ENABLE;
-
-	ixp23xx_restart(mode, cmd);
-}
-
-MACHINE_START(IXDP2351, "Intel IXDP2351 Development Platform")
-	/* Maintainer: MontaVista Software, Inc. */
-	.map_io		= ixdp2351_map_io,
-	.init_irq	= ixdp2351_init_irq,
-	.timer		= &ixp23xx_timer,
-	.atag_offset	= 0x100,
-	.init_machine	= ixdp2351_init,
-	.restart	= ixdp2351_restart,
-MACHINE_END
diff --git a/arch/arm/mach-ixp23xx/pci.c b/arch/arm/mach-ixp23xx/pci.c
deleted file mode 100644
index 911f5a5..0000000
--- a/arch/arm/mach-ixp23xx/pci.c
+++ /dev/null
@@ -1,294 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/pci.c
- *
- * PCI routines for IXP23XX based systems
- *
- * Copyright (c) 2005 MontaVista Software, Inc.
- *
- * based on original code:
- *
- * Author: Naeem Afzal <naeem.m.afzal@intel.com>
- * Copyright 2002-2005 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <asm/sizes.h>
-#include <asm/mach/pci.h>
-#include <mach/hardware.h>
-
-extern int (*external_fault) (unsigned long, struct pt_regs *);
-
-static volatile int pci_master_aborts = 0;
-
-#ifdef DEBUG
-#define DBG(x...)	printk(x)
-#else
-#define DBG(x...)
-#endif
-
-int clear_master_aborts(void);
-
-static u32
-*ixp23xx_pci_config_addr(unsigned int bus_nr, unsigned int devfn, int where)
-{
-	u32 *paddress;
-
-	/*
-	 * Must be dword aligned
-	 */
-	where &= ~3;
-
-	/*
-	 * For top bus, generate type 0, else type 1
-	 */
-	if (!bus_nr) {
-		if (PCI_SLOT(devfn) >= 8)
-			return 0;
-
-		paddress = (u32 *) (IXP23XX_PCI_CFG0_VIRT
-				    | (1 << (PCI_SLOT(devfn) + 16))
-				    | (PCI_FUNC(devfn) << 8) | where);
-	} else {
-		paddress = (u32 *) (IXP23XX_PCI_CFG1_VIRT
-				    | (bus_nr << 16)
-				    | (PCI_SLOT(devfn) << 11)
-				    | (PCI_FUNC(devfn) << 8) | where);
-	}
-
-	return paddress;
-}
-
-/*
- * Mask table, bits to mask for quantity of size 1, 2 or 4 bytes.
- * 0 and 3 are not valid indexes...
- */
-static u32 bytemask[] = {
-	/*0*/	0,
-	/*1*/	0xff,
-	/*2*/	0xffff,
-	/*3*/	0,
-	/*4*/	0xffffffff,
-};
-
-static int ixp23xx_pci_read_config(struct pci_bus *bus, unsigned int devfn,
-				int where, int size, u32 *value)
-{
-	u32 n;
-	u32 *addr;
-
-	n = where % 4;
-
-	DBG("In config_read(%d) %d from dev %d:%d:%d\n", size, where,
-		bus->number, PCI_SLOT(devfn), PCI_FUNC(devfn));
-
-	addr = ixp23xx_pci_config_addr(bus->number, devfn, where);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	pci_master_aborts = 0;
-	*value = (*addr >> (8*n)) & bytemask[size];
-	if (pci_master_aborts) {
-			pci_master_aborts = 0;
-			*value = 0xffffffff;
-			return PCIBIOS_DEVICE_NOT_FOUND;
-		}
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-/*
- * We don't do error checking on the address for writes.
- * It's assumed that the user checked for the device existing first
- * by doing a read first.
- */
-static int ixp23xx_pci_write_config(struct pci_bus *bus, unsigned int devfn,
-					int where, int size, u32 value)
-{
-	u32 mask;
-	u32 *addr;
-	u32 temp;
-
-	mask = ~(bytemask[size] << ((where % 0x4) * 8));
-	addr = ixp23xx_pci_config_addr(bus->number, devfn, where);
-	if (!addr)
-		return PCIBIOS_DEVICE_NOT_FOUND;
-	temp = (u32) (value) << ((where % 0x4) * 8);
-	*addr = (*addr & mask) | temp;
-
-	clear_master_aborts();
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-struct pci_ops ixp23xx_pci_ops = {
-	.read	= ixp23xx_pci_read_config,
-	.write	= ixp23xx_pci_write_config,
-};
-
-struct pci_bus *ixp23xx_pci_scan_bus(int nr, struct pci_sys_data *sysdata)
-{
-	return pci_scan_root_bus(NULL, sysdata->busnr, &ixp23xx_pci_ops,
-				 sysdata, &sysdata->resources);
-}
-
-int ixp23xx_pci_abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
-{
-	volatile unsigned long temp;
-	unsigned long flags;
-
-	pci_master_aborts = 1;
-
-	local_irq_save(flags);
-	temp = *IXP23XX_PCI_CONTROL;
-
-	/*
-	 * master abort and cmd tgt err
-	 */
-	if (temp & ((1 << 8) | (1 << 5)))
-		*IXP23XX_PCI_CONTROL = temp;
-
-	temp = *IXP23XX_PCI_CMDSTAT;
-
-	if (temp & (1 << 29))
-		*IXP23XX_PCI_CMDSTAT = temp;
-	local_irq_restore(flags);
-
-	/*
-	 * If it was an imprecise abort, then we need to correct the
-	 * return address to be _after_ the instruction.
-	 */
-	if (fsr & (1 << 10))
-		regs->ARM_pc += 4;
-
-	return 0;
-}
-
-int clear_master_aborts(void)
-{
-	volatile u32 temp;
-
-	temp = *IXP23XX_PCI_CONTROL;
-
-	/*
-	 * master abort and cmd tgt err
-	 */
-	if (temp & ((1 << 8) | (1 << 5)))
-		*IXP23XX_PCI_CONTROL = temp;
-
-	temp = *IXP23XX_PCI_CMDSTAT;
-
-	if (temp & (1 << 29))
-		*IXP23XX_PCI_CMDSTAT = temp;
-
-	return 0;
-}
-
-static void __init ixp23xx_pci_common_init(void)
-{
-#ifdef __ARMEB__
-	*IXP23XX_PCI_CONTROL |= 0x20000;	/* set I/O swapping */
-#endif
-	/*
-	 * ADDR_31 needs to be clear for PCI memory access to CPP memory
-	 */
-	*IXP23XX_CPP2XSI_CURR_XFER_REG3 &= ~IXP23XX_CPP2XSI_ADDR_31;
-	*IXP23XX_CPP2XSI_CURR_XFER_REG3 |= IXP23XX_CPP2XSI_PSH_OFF;
-
-	/*
-	 * Select correct memory for PCI inbound transactions
-	 */
-	if (ixp23xx_cpp_boot()) {
-		*IXP23XX_PCI_CPP_ADDR_BITS &= ~(1 << 1);
-	} else {
-		*IXP23XX_PCI_CPP_ADDR_BITS |= (1 << 1);
-
-		/*
-		 * Enable coherency on A2 silicon.
-		 */
-		if (arch_is_coherent())
-			*IXP23XX_CPP2XSI_CURR_XFER_REG3 &= ~IXP23XX_CPP2XSI_COH_OFF;
-	}
-}
-
-void __init ixp23xx_pci_preinit(void)
-{
-	pcibios_min_io = 0;
-	pcibios_min_mem = 0xe0000000;
-
-	pci_set_flags(0);
-
-	ixp23xx_pci_common_init();
-
-	hook_fault_code(16+6, ixp23xx_pci_abort_handler, SIGBUS, 0,
-			"PCI config cycle to non-existent device");
-
-	*IXP23XX_PCI_ADDR_EXT = 0x0000e000;
-}
-
-/*
- * Prevent PCI layer from seeing the inbound host-bridge resources
- */
-static void __devinit pci_fixup_ixp23xx(struct pci_dev *dev)
-{
-	int i;
-
-	dev->class &= 0xff;
-	dev->class |= PCI_CLASS_BRIDGE_HOST << 8;
-	for (i = 0; i < PCI_NUM_RESOURCES; i++) {
-		dev->resource[i].start = 0;
-		dev->resource[i].end   = 0;
-		dev->resource[i].flags = 0;
-	}
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9002, pci_fixup_ixp23xx);
-
-/*
- * IXP2300 systems often have large resource requirements, so we just
- * use our own resource space.
- */
-static struct resource ixp23xx_pci_mem_space = {
-	.start	= IXP23XX_PCI_MEM_START,
-	.end	= IXP23XX_PCI_MEM_START + IXP23XX_PCI_MEM_SIZE - 1,
-	.flags	= IORESOURCE_MEM,
-	.name	= "PCI Mem Space"
-};
-
-static struct resource ixp23xx_pci_io_space = {
-	.start	= 0x00000100,
-	.end	= 0x01ffffff,
-	.flags	= IORESOURCE_IO,
-	.name	= "PCI I/O Space"
-};
-
-int ixp23xx_pci_setup(int nr, struct pci_sys_data *sys)
-{
-	if (nr >= 1)
-		return 0;
-
-	pci_add_resource_offset(&sys->resources,
-				&ixp23xx_pci_io_space, sys->io_offset);
-	pci_add_resource_offset(&sys->resources,
-				&ixp23xx_pci_mem_space, sys->mem_offset);
-
-	return 1;
-}
-
-void __init ixp23xx_pci_slave_init(void)
-{
-	ixp23xx_pci_common_init();
-}
diff --git a/arch/arm/mach-ixp23xx/roadrunner.c b/arch/arm/mach-ixp23xx/roadrunner.c
deleted file mode 100644
index eaaa3fa..0000000
--- a/arch/arm/mach-ixp23xx/roadrunner.c
+++ /dev/null
@@ -1,180 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/roadrunner.c
- *
- * RoadRunner board-specific routines
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2005 (c) MontaVista Software, Inc.
- *
- * Based on 2.4 code Copyright 2005 (c) ADI Engineering Corporation
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/bitops.h>
-#include <linux/ioport.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_core.h>
-#include <linux/device.h>
-#include <linux/mm.h>
-#include <linux/pci.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-#include <asm/tlbflush.h>
-#include <asm/pgtable.h>
-
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-
-/*
- * Interrupt mapping
- */
-#define INTA		IRQ_ROADRUNNER_PCI_INTA
-#define INTB		IRQ_ROADRUNNER_PCI_INTB
-#define INTC		IRQ_ROADRUNNER_PCI_INTC
-#define INTD		IRQ_ROADRUNNER_PCI_INTD
-
-#define INTC_PIN	IXP23XX_GPIO_PIN_11
-#define INTD_PIN	IXP23XX_GPIO_PIN_12
-
-static int __init roadrunner_map_irq(const struct pci_dev *dev, u8 idsel,
-	u8 pin)
-{
-	static int pci_card_slot_irq[] = {INTB, INTC, INTD, INTA};
-	static int pmc_card_slot_irq[] = {INTA, INTB, INTC, INTD};
-	static int usb_irq[] = {INTB, INTC, INTD, -1};
-	static int mini_pci_1_irq[] = {INTB, INTC, -1, -1};
-	static int mini_pci_2_irq[] = {INTC, INTD, -1, -1};
-
-	switch(dev->bus->number) {
-		case 0:
-			switch(dev->devfn) {
-			case 0x0: // PCI-PCI bridge
-				break;
-			case 0x8: // PCI Card Slot
-				return pci_card_slot_irq[pin - 1];
-			case 0x10: // PMC Slot
-				return pmc_card_slot_irq[pin - 1];
-			case 0x18: // PMC Slot Secondary Agent
-				break;
-			case 0x20: // IXP Processor
-				break;
-			default:
-				return NO_IRQ;
-			}
-			break;
-
-		case 1:
-			switch(dev->devfn) {
-			case 0x0: // IDE Controller
-				return (pin == 1) ? INTC : -1;
-			case 0x8: // USB fun 0
-			case 0x9: // USB fun 1
-			case 0xa: // USB fun 2
-				return usb_irq[pin - 1];
-			case 0x10: // Mini PCI 1
-				return mini_pci_1_irq[pin-1];
-			case 0x18: // Mini PCI 2
-				return mini_pci_2_irq[pin-1];
-			case 0x20: // MEM slot
-				return (pin == 1) ? INTA : -1;
-			default:
-				return NO_IRQ;
-			}
-			break;
-
-		default:
-			return NO_IRQ;
-	}
-
-	return NO_IRQ;
-}
-
-static void __init roadrunner_pci_preinit(void)
-{
-	irq_set_irq_type(IRQ_ROADRUNNER_PCI_INTC, IRQ_TYPE_LEVEL_LOW);
-	irq_set_irq_type(IRQ_ROADRUNNER_PCI_INTD, IRQ_TYPE_LEVEL_LOW);
-
-	ixp23xx_pci_preinit();
-}
-
-static struct hw_pci roadrunner_pci __initdata = {
-	.nr_controllers	= 1,
-	.preinit	= roadrunner_pci_preinit,
-	.setup		= ixp23xx_pci_setup,
-	.scan		= ixp23xx_pci_scan_bus,
-	.map_irq	= roadrunner_map_irq,
-};
-
-static int __init roadrunner_pci_init(void)
-{
-	if (machine_is_roadrunner())
-		pci_common_init(&roadrunner_pci);
-
-	return 0;
-};
-
-subsys_initcall(roadrunner_pci_init);
-
-static struct physmap_flash_data roadrunner_flash_data = {
-	.width		= 2,
-};
-
-static struct resource roadrunner_flash_resource = {
-	.start		= 0x90000000,
-	.end		= 0x93ffffff,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device roadrunner_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &roadrunner_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &roadrunner_flash_resource,
-};
-
-static void __init roadrunner_init(void)
-{
-	platform_device_register(&roadrunner_flash);
-
-	/*
-	 * Mark flash as writeable
-	 */
-	IXP23XX_EXP_CS0[0] |= IXP23XX_FLASH_WRITABLE;
-	IXP23XX_EXP_CS0[1] |= IXP23XX_FLASH_WRITABLE;
-	IXP23XX_EXP_CS0[2] |= IXP23XX_FLASH_WRITABLE;
-	IXP23XX_EXP_CS0[3] |= IXP23XX_FLASH_WRITABLE;
-
-	ixp23xx_sys_init();
-}
-
-MACHINE_START(ROADRUNNER, "ADI Engineering RoadRunner Development Platform")
-	/* Maintainer: Deepak Saxena */
-	.map_io		= ixp23xx_map_io,
-	.init_irq	= ixp23xx_init_irq,
-	.timer		= &ixp23xx_timer,
-	.atag_offset	= 0x100,
-	.init_machine	= roadrunner_init,
-	.restart	= ixp23xx_restart,
-MACHINE_END
diff --git a/drivers/char/hw_random/Kconfig b/drivers/char/hw_random/Kconfig
index 0689bf6..b2402eb 100644
--- a/drivers/char/hw_random/Kconfig
+++ b/drivers/char/hw_random/Kconfig
@@ -62,7 +62,7 @@
 
 config HW_RANDOM_ATMEL
 	tristate "Atmel Random Number Generator support"
-	depends on HW_RANDOM && ARCH_AT91SAM9G45
+	depends on HW_RANDOM && HAVE_CLK
 	default HW_RANDOM
 	---help---
 	  This driver provides kernel-side support for the Random Number
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 2a21419..75838d7 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -489,10 +489,10 @@
 
 config TOUCHSCREEN_ATMEL_TSADCC
 	tristate "Atmel Touchscreen Interface"
-	depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
+	depends on ARCH_AT91
 	help
 	  Say Y here if you have a 4-wire touchscreen connected to the
-          ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
+          ADC Controller on your Atmel SoC.
 
 	  If unsure, say N.
 
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 8c8377d..4161bfe 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -838,7 +838,7 @@
 
 config RTC_DRV_AT91RM9200
 	tristate "AT91RM9200 or some AT91SAM9 RTC"
-	depends on ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
+	depends on ARCH_AT91
 	help
 	  Driver for the internal RTC (Realtime Clock) module found on
 	  Atmel AT91RM9200's and some  AT91SAM9 chips. On AT91SAM9 chips