| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * at91-sama5d2_xplained.dts - Device Tree file for SAMA5D2 Xplained board |
| * |
| * Copyright (C) 2015 Atmel, |
| * 2015 Nicolas Ferre <nicolas.ferre@atmel.com> |
| */ |
| /dts-v1/; |
| #include "sama5d2.dtsi" |
| #include "sama5d2-pinfunc.h" |
| #include <dt-bindings/mfd/atmel-flexcom.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/regulator/active-semi,8945a-regulator.h> |
| |
| / { |
| model = "Atmel SAMA5D2 Xplained"; |
| compatible = "atmel,sama5d2-xplained", "atmel,sama5d2", "atmel,sama5"; |
| |
| aliases { |
| serial0 = &uart1; /* DBGU */ |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; /* XPRO EXT2 */ |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| clocks { |
| slow_xtal { |
| clock-frequency = <32768>; |
| }; |
| |
| main_xtal { |
| clock-frequency = <12000000>; |
| }; |
| }; |
| |
| ahb { |
| usb0: gadget@300000 { |
| atmel,vbus-gpio = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usba_vbus>; |
| status = "okay"; |
| }; |
| |
| usb1: ohci@400000 { |
| num-ports = <3>; |
| atmel,vbus-gpio = <0 /* &pioA PIN_PB9 GPIO_ACTIVE_HIGH */ |
| &pioA PIN_PB10 GPIO_ACTIVE_HIGH |
| 0 |
| >; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb_default>; |
| status = "okay"; |
| }; |
| |
| usb2: ehci@500000 { |
| status = "okay"; |
| }; |
| |
| sdmmc0: sdio-host@a0000000 { |
| bus-width = <8>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sdmmc0_default>; |
| non-removable; |
| mmc-ddr-3_3v; |
| status = "okay"; |
| }; |
| |
| sdmmc1: sdio-host@b0000000 { |
| bus-width = <4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sdmmc1_default>; |
| status = "okay"; /* conflict with qspi0 */ |
| vqmmc-supply = <&vdd_3v3_reg>; |
| vmmc-supply = <&vdd_3v3_reg>; |
| }; |
| |
| apb { |
| qspi0: spi@f0020000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_qspi0_default>; |
| status = "disabled"; /* conflict with sdmmc1 */ |
| |
| flash@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <80000000>; |
| spi-tx-bus-width = <4>; |
| spi-rx-bus-width = <4>; |
| m25p,fast-read; |
| |
| at91bootstrap@0 { |
| label = "at91bootstrap"; |
| reg = <0x00000000 0x00040000>; |
| }; |
| |
| bootloader@40000 { |
| label = "bootloader"; |
| reg = <0x00040000 0x000c0000>; |
| }; |
| |
| bootloaderenvred@100000 { |
| label = "bootloader env redundant"; |
| reg = <0x00100000 0x00040000>; |
| }; |
| |
| bootloaderenv@140000 { |
| label = "bootloader env"; |
| reg = <0x00140000 0x00040000>; |
| }; |
| |
| dtb@180000 { |
| label = "device tree"; |
| reg = <0x00180000 0x00080000>; |
| }; |
| |
| kernel@200000 { |
| label = "kernel"; |
| reg = <0x00200000 0x00600000>; |
| }; |
| |
| misc@800000 { |
| label = "misc"; |
| reg = <0x00800000 0x00000000>; |
| }; |
| }; |
| }; |
| |
| spi0: spi@f8000000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi0_default>; |
| status = "okay"; |
| |
| flash@0 { |
| compatible = "atmel,at25df321a"; |
| reg = <0>; |
| spi-max-frequency = <50000000>; |
| }; |
| }; |
| |
| macb0: ethernet@f8008000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| phy-mode = "rmii"; |
| status = "okay"; |
| |
| ethernet-phy@1 { |
| reg = <0x1>; |
| interrupt-parent = <&pioA>; |
| interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |
| |
| tcb0: timer@f800c000 { |
| timer0: timer@0 { |
| compatible = "atmel,tcb-timer"; |
| reg = <0>; |
| }; |
| |
| timer1: timer@1 { |
| compatible = "atmel,tcb-timer"; |
| reg = <1>; |
| }; |
| }; |
| |
| uart1: serial@f8020000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1_default>; |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| status = "okay"; |
| }; |
| |
| i2c0: i2c@f8028000 { |
| dmas = <0>, <0>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c0_default>; |
| pinctrl-1 = <&pinctrl_i2c0_gpio>; |
| sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>; |
| scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-sda-hold-time-ns = <350>; |
| status = "okay"; |
| |
| pmic@5b { |
| compatible = "active-semi,act8945a"; |
| reg = <0x5b>; |
| active-semi,vsel-high; |
| status = "okay"; |
| |
| regulators { |
| vdd_1v35_reg: REG_DCDC1 { |
| regulator-name = "VDD_1V35"; |
| regulator-min-microvolt = <1350000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>, |
| <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-min-microvolt = <1400000>; |
| regulator-suspend-max-microvolt = <1400000>; |
| regulator-changeable-in-suspend; |
| regulator-mode = <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| }; |
| }; |
| |
| vdd_1v2_reg: REG_DCDC2 { |
| regulator-name = "VDD_1V2"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>, |
| <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_3v3_reg: REG_DCDC3 { |
| regulator-name = "VDD_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>, |
| <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_fuse_reg: REG_LDO1 { |
| regulator-name = "VDD_FUSE"; |
| regulator-min-microvolt = <2500000>; |
| regulator-max-microvolt = <2500000>; |
| regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>, |
| <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_3v3_lp_reg: REG_LDO2 { |
| regulator-name = "VDD_3V3_LP"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>, |
| <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_led_reg: REG_LDO3 { |
| regulator-name = "VDD_LED"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>, |
| <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_sdhc_1v8_reg: REG_LDO4 { |
| regulator-name = "VDD_SDHC_1V8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>, |
| <ACT8945A_REGULATOR_MODE_LOWPOWER>; |
| regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>; |
| regulator-always-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| |
| charger { |
| compatible = "active-semi,act8945a-charger"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; |
| interrupt-parent = <&pioA>; |
| interrupts = <PIN_PB13 IRQ_TYPE_EDGE_RISING>; |
| |
| active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>; |
| active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>; |
| active-semi,input-voltage-threshold-microvolt = <6600>; |
| active-semi,precondition-timeout = <40>; |
| active-semi,total-timeout = <3>; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| pwm0: pwm@f802c000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm0_pwm2_default>; |
| status = "disabled"; /* conflict with leds */ |
| }; |
| |
| flx0: flexcom@f8034000 { |
| atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; |
| status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */ |
| |
| uart5: serial@200 { |
| dmas = <0>, <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flx0_default>; |
| status = "okay"; |
| }; |
| |
| i2c2: i2c@600 { |
| dmas = <0>, <0>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_flx0_default>; |
| pinctrl-1 = <&pinctrl_i2c2_gpio>; |
| sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>; |
| scl-gpios = <&pioA PIN_PB29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-sda-hold-time-ns = <350>; |
| i2c-analog-filter; |
| i2c-digital-filter; |
| i2c-digital-filter-width-ns = <35>; |
| status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */ |
| }; |
| }; |
| |
| shdwc@f8048010 { |
| debounce-delay-us = <976>; |
| atmel,wakeup-rtc-timer; |
| |
| input@0 { |
| reg = <0>; |
| }; |
| }; |
| |
| watchdog@f8048040 { |
| status = "okay"; |
| }; |
| |
| i2s0: i2s@f8050000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2s0_default>; |
| status = "disabled"; /* conflict with can0 */ |
| }; |
| |
| can0: can@f8054000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_can0_default>; |
| status = "okay"; |
| }; |
| |
| uart3: serial@fc008000 { |
| atmel,use-dma-rx; |
| atmel,use-dma-tx; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3_default>; |
| status = "okay"; |
| }; |
| |
| flx4: flexcom@fc018000 { |
| atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>; |
| status = "okay"; |
| |
| i2c6: i2c@600 { |
| dmas = <0>, <0>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_flx4_default>; |
| pinctrl-1 = <&pinctrl_flx4_gpio>; |
| sda-gpios = <&pioA PIN_PD12 GPIO_ACTIVE_HIGH>; |
| scl-gpios = <&pioA PIN_PD13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-analog-filter; |
| i2c-digital-filter; |
| i2c-digital-filter-width-ns = <35>; |
| status = "okay"; |
| }; |
| }; |
| |
| i2c1: i2c@fc028000 { |
| dmas = <0>, <0>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c1_default>; |
| i2c-analog-filter; |
| i2c-digital-filter; |
| i2c-digital-filter-width-ns = <35>; |
| pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>; |
| scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| |
| at24@54 { |
| compatible = "atmel,24c02"; |
| reg = <0x54>; |
| pagesize = <16>; |
| }; |
| }; |
| |
| adc: adc@fc030000 { |
| vddana-supply = <&vdd_3v3_lp_reg>; |
| vref-supply = <&vdd_3v3_lp_reg>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>; |
| status = "okay"; |
| }; |
| |
| pinctrl@fc038000 { |
| /* |
| * There is no real pinmux for ADC, if the pin |
| * is not requested by another peripheral then |
| * the muxing is done when channel is enabled. |
| * Requesting pins for ADC is GPIO is |
| * encouraged to prevent conflicts and to |
| * disable bias in order to be in the same |
| * state when the pin is not muxed to the adc. |
| */ |
| pinctrl_adc_default: adc_default { |
| pinmux = <PIN_PD23__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_can0_default: can0_default { |
| pinmux = <PIN_PC10__CANTX0>, |
| <PIN_PC11__CANRX0>; |
| bias-disable; |
| }; |
| |
| pinctrl_can1_default: can1_default { |
| pinmux = <PIN_PC26__CANTX1>, |
| <PIN_PC27__CANRX1>; |
| bias-disable; |
| }; |
| |
| /* |
| * The ADTRG pin can work on any edge type. |
| * In here it's being pulled up, so need to |
| * connect it to ground to get an edge e.g. |
| * Trigger can be configured on falling, rise |
| * or any edge, and the pull-up can be changed |
| * to pull-down or left floating according to |
| * needs. |
| */ |
| pinctrl_adtrg_default: adtrg_default { |
| pinmux = <PIN_PD31__ADTRG>; |
| bias-pull-up; |
| }; |
| |
| pinctrl_charger_chglev: charger_chglev { |
| pinmux = <PIN_PA12__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_charger_irq: charger_irq { |
| pinmux = <PIN_PB13__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_charger_lbo: charger_lbo { |
| pinmux = <PIN_PC8__GPIO>; |
| bias-pull-up; |
| }; |
| |
| pinctrl_classd_default_pfets: classd_default_pfets { |
| pinmux = <PIN_PB1__CLASSD_R0>, |
| <PIN_PB3__CLASSD_R2>; |
| bias-pull-up; |
| }; |
| |
| pinctrl_classd_default_nfets: classd_default_nfets { |
| pinmux = <PIN_PB2__CLASSD_R1>, |
| <PIN_PB4__CLASSD_R3>; |
| bias-pull-down; |
| }; |
| |
| pinctrl_flx0_default: flx0_default { |
| pinmux = <PIN_PB28__FLEXCOM0_IO0>, |
| <PIN_PB29__FLEXCOM0_IO1>; |
| bias-disable; |
| }; |
| |
| pinctrl_flx4_default: flx4_default { |
| pinmux = <PIN_PD12__FLEXCOM4_IO0>, |
| <PIN_PD13__FLEXCOM4_IO1>; |
| bias-disable; |
| }; |
| |
| pinctrl_flx4_gpio: flx4_gpio { |
| pinmux = <PIN_PD12__GPIO>, |
| <PIN_PD13__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_i2c0_default: i2c0_default { |
| pinmux = <PIN_PD21__TWD0>, |
| <PIN_PD22__TWCK0>; |
| bias-disable; |
| }; |
| |
| pinctrl_i2c0_gpio: i2c0_gpio { |
| pinmux = <PIN_PD21__GPIO>, |
| <PIN_PD22__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_i2c1_default: i2c1_default { |
| pinmux = <PIN_PD4__TWD1>, |
| <PIN_PD5__TWCK1>; |
| bias-disable; |
| }; |
| |
| pinctrl_i2c1_gpio: i2c1_gpio { |
| pinmux = <PIN_PD4__GPIO>, |
| <PIN_PD5__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_i2c2_gpio: i2c2_gpio { |
| pinmux = <PIN_PB28__GPIO>, |
| <PIN_PB29__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_i2s0_default: i2s0_default { |
| pinmux = <PIN_PC1__I2SC0_CK>, |
| <PIN_PC2__I2SC0_MCK>, |
| <PIN_PC3__I2SC0_WS>, |
| <PIN_PC4__I2SC0_DI0>, |
| <PIN_PC5__I2SC0_DO0>; |
| bias-disable; |
| }; |
| |
| pinctrl_i2s1_default: i2s1_default { |
| pinmux = <PIN_PA15__I2SC1_CK>, |
| <PIN_PA14__I2SC1_MCK>, |
| <PIN_PA16__I2SC1_WS>, |
| <PIN_PA17__I2SC1_DI0>, |
| <PIN_PA18__I2SC1_DO0>; |
| bias-disable; |
| }; |
| |
| pinctrl_key_gpio_default: key_gpio_default { |
| pinmux = <PIN_PB9__GPIO>; |
| bias-pull-up; |
| }; |
| |
| pinctrl_led_gpio_default: led_gpio_default { |
| pinmux = <PIN_PB0__GPIO>, |
| <PIN_PB5__GPIO>, |
| <PIN_PB6__GPIO>; |
| bias-pull-up; |
| }; |
| |
| pinctrl_macb0_default: macb0_default { |
| pinmux = <PIN_PB14__GTXCK>, |
| <PIN_PB15__GTXEN>, |
| <PIN_PB16__GRXDV>, |
| <PIN_PB17__GRXER>, |
| <PIN_PB18__GRX0>, |
| <PIN_PB19__GRX1>, |
| <PIN_PB20__GTX0>, |
| <PIN_PB21__GTX1>, |
| <PIN_PB22__GMDC>, |
| <PIN_PB23__GMDIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_macb0_phy_irq: macb0_phy_irq { |
| pinmux = <PIN_PC9__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_qspi0_default: qspi0_default { |
| sck_cs { |
| pinmux = <PIN_PA22__QSPI0_SCK>, |
| <PIN_PA23__QSPI0_CS>; |
| bias-disable; |
| }; |
| |
| data { |
| pinmux = <PIN_PA24__QSPI0_IO0>, |
| <PIN_PA25__QSPI0_IO1>, |
| <PIN_PA26__QSPI0_IO2>, |
| <PIN_PA27__QSPI0_IO3>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pinctrl_sdmmc0_default: sdmmc0_default { |
| cmd_data { |
| pinmux = <PIN_PA1__SDMMC0_CMD>, |
| <PIN_PA2__SDMMC0_DAT0>, |
| <PIN_PA3__SDMMC0_DAT1>, |
| <PIN_PA4__SDMMC0_DAT2>, |
| <PIN_PA5__SDMMC0_DAT3>, |
| <PIN_PA6__SDMMC0_DAT4>, |
| <PIN_PA7__SDMMC0_DAT5>, |
| <PIN_PA8__SDMMC0_DAT6>, |
| <PIN_PA9__SDMMC0_DAT7>; |
| bias-disable; |
| }; |
| |
| ck_cd_rstn { |
| pinmux = <PIN_PA0__SDMMC0_CK>, |
| <PIN_PA10__SDMMC0_RSTN>, |
| <PIN_PA13__SDMMC0_CD>; |
| bias-disable; |
| }; |
| }; |
| |
| pinctrl_sdmmc1_default: sdmmc1_default { |
| cmd_data { |
| pinmux = <PIN_PA28__SDMMC1_CMD>, |
| <PIN_PA18__SDMMC1_DAT0>, |
| <PIN_PA19__SDMMC1_DAT1>, |
| <PIN_PA20__SDMMC1_DAT2>, |
| <PIN_PA21__SDMMC1_DAT3>; |
| bias-disable; |
| }; |
| |
| conf-ck_cd { |
| pinmux = <PIN_PA22__SDMMC1_CK>, |
| <PIN_PA30__SDMMC1_CD>; |
| bias-disable; |
| }; |
| }; |
| |
| pinctrl_spi0_default: spi0_default { |
| pinmux = <PIN_PA14__SPI0_SPCK>, |
| <PIN_PA15__SPI0_MOSI>, |
| <PIN_PA16__SPI0_MISO>, |
| <PIN_PA17__SPI0_NPCS0>; |
| bias-disable; |
| }; |
| |
| pinctrl_uart1_default: uart1_default { |
| pinmux = <PIN_PD2__URXD1>, |
| <PIN_PD3__UTXD1>; |
| bias-disable; |
| }; |
| |
| pinctrl_uart3_default: uart3_default { |
| pinmux = <PIN_PB11__URXD3>, |
| <PIN_PB12__UTXD3>; |
| bias-disable; |
| }; |
| |
| pinctrl_usb_default: usb_default { |
| pinmux = <PIN_PB10__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_usba_vbus: usba_vbus { |
| pinmux = <PIN_PA31__GPIO>; |
| bias-disable; |
| }; |
| |
| pinctrl_pwm0_pwm2_default: pwm0_pwm2_default { |
| pinmux = <PIN_PB5__PWMH2>, |
| <PIN_PB6__PWML2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| classd: classd@fc048000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_classd_default_pfets &pinctrl_classd_default_nfets>; |
| atmel,pwm-type = "diff"; |
| atmel,non-overlap-time = <10>; |
| status = "okay"; |
| }; |
| |
| i2s1: i2s@fc04c000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2s1_default>; |
| status = "disabled"; /* conflict with spi0, sdmmc1 */ |
| }; |
| |
| can1: can@fc050000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_can1_default>; |
| status = "okay"; |
| }; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_key_gpio_default>; |
| |
| button { |
| label = "PB_USER"; |
| gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_PROG1>; |
| wakeup-source; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_led_gpio_default>; |
| status = "okay"; /* conflict with pwm0 */ |
| |
| red { |
| label = "red"; |
| gpios = <&pioA PIN_PB6 GPIO_ACTIVE_LOW>; |
| }; |
| |
| |
| green { |
| label = "green"; |
| gpios = <&pioA PIN_PB5 GPIO_ACTIVE_LOW>; |
| }; |
| |
| blue { |
| label = "blue"; |
| gpios = <&pioA PIN_PB0 GPIO_ACTIVE_LOW>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| }; |
