| // SPDX-License-Identifier: GPL-2.0 |
| // |
| // Copyright 2014 Freescale Semiconductor, Inc. |
| |
| #include <dt-bindings/clock/imx6sx-clock.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include "imx6sx-pinfunc.h" |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| /* |
| * The decompressor and also some bootloaders rely on a |
| * pre-existing /chosen node to be available to insert the |
| * command line and merge other ATAGS info. |
| */ |
| chosen {}; |
| |
| aliases { |
| can0 = &flexcan1; |
| can1 = &flexcan2; |
| ethernet0 = &fec1; |
| ethernet1 = &fec2; |
| gpio0 = &gpio1; |
| gpio1 = &gpio2; |
| gpio2 = &gpio3; |
| gpio3 = &gpio4; |
| gpio4 = &gpio5; |
| gpio5 = &gpio6; |
| gpio6 = &gpio7; |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| i2c3 = &i2c4; |
| mmc0 = &usdhc1; |
| mmc1 = &usdhc2; |
| mmc2 = &usdhc3; |
| mmc3 = &usdhc4; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| serial4 = &uart5; |
| serial5 = &uart6; |
| spi0 = &ecspi1; |
| spi1 = &ecspi2; |
| spi2 = &ecspi3; |
| spi3 = &ecspi4; |
| spi4 = &ecspi5; |
| usb0 = &usbotg1; |
| usb1 = &usbotg2; |
| usb2 = &usbh; |
| usbphy0 = &usbphy1; |
| usbphy1 = &usbphy2; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| reg = <0>; |
| next-level-cache = <&L2>; |
| operating-points = < |
| /* kHz uV */ |
| 996000 1250000 |
| 792000 1175000 |
| 396000 1075000 |
| 198000 975000 |
| >; |
| fsl,soc-operating-points = < |
| /* ARM kHz SOC uV */ |
| 996000 1175000 |
| 792000 1175000 |
| 396000 1175000 |
| 198000 1175000 |
| >; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| #cooling-cells = <2>; |
| clocks = <&clks IMX6SX_CLK_ARM>, |
| <&clks IMX6SX_CLK_PLL2_PFD2>, |
| <&clks IMX6SX_CLK_STEP>, |
| <&clks IMX6SX_CLK_PLL1_SW>, |
| <&clks IMX6SX_CLK_PLL1_SYS>; |
| clock-names = "arm", "pll2_pfd2_396m", "step", |
| "pll1_sw", "pll1_sys"; |
| arm-supply = <®_arm>; |
| soc-supply = <®_soc>; |
| nvmem-cells = <&cpu_speed_grade>; |
| nvmem-cell-names = "speed_grade"; |
| }; |
| }; |
| |
| ckil: clock-ckil { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "ckil"; |
| }; |
| |
| osc: clock-osc { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| clock-output-names = "osc"; |
| }; |
| |
| ipp_di0: clock-ipp-di0 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| clock-output-names = "ipp_di0"; |
| }; |
| |
| ipp_di1: clock-ipp-di1 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| clock-output-names = "ipp_di1"; |
| }; |
| |
| anaclk1: clock-anaclk1 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| clock-output-names = "anaclk1"; |
| }; |
| |
| anaclk2: clock-anaclk2 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| clock-output-names = "anaclk2"; |
| }; |
| |
| mqs: mqs { |
| compatible = "fsl,imx6sx-mqs"; |
| gpr = <&gpr>; |
| status = "disabled"; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a9-pmu"; |
| interrupt-parent = <&gpc>; |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| usbphynop1: usbphynop1 { |
| compatible = "usb-nop-xceiv"; |
| #phy-cells = <0>; |
| }; |
| |
| soc: soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "simple-bus"; |
| interrupt-parent = <&gpc>; |
| ranges; |
| |
| ocram_s: sram@8f8000 { |
| compatible = "mmio-sram"; |
| reg = <0x008f8000 0x4000>; |
| ranges = <0 0x008f8000 0x4000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| clocks = <&clks IMX6SX_CLK_OCRAM_S>; |
| }; |
| |
| ocram: sram@900000 { |
| compatible = "mmio-sram"; |
| reg = <0x00900000 0x20000>; |
| ranges = <0 0x00900000 0x20000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| clocks = <&clks IMX6SX_CLK_OCRAM>; |
| }; |
| |
| intc: interrupt-controller@a01000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0x00a01000 0x1000>, |
| <0x00a00100 0x100>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| L2: cache-controller@a02000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0x00a02000 0x1000>; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; |
| cache-unified; |
| cache-level = <2>; |
| arm,tag-latency = <4 2 3>; |
| arm,data-latency = <4 2 3>; |
| }; |
| |
| gpu: gpu@1800000 { |
| compatible = "vivante,gc"; |
| reg = <0x01800000 0x4000>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_GPU>, |
| <&clks IMX6SX_CLK_GPU>, |
| <&clks IMX6SX_CLK_GPU>; |
| clock-names = "bus", "core", "shader"; |
| power-domains = <&pd_pu>; |
| }; |
| |
| dma_apbh: dma-apbh@1804000 { |
| compatible = "fsl,imx6sx-dma-apbh", "fsl,imx28-dma-apbh"; |
| reg = <0x01804000 0x2000>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; |
| #dma-cells = <1>; |
| dma-channels = <4>; |
| clocks = <&clks IMX6SX_CLK_APBH_DMA>; |
| }; |
| |
| gpmi: nand-controller@1806000{ |
| compatible = "fsl,imx6sx-gpmi-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x01806000 0x2000>, <0x01808000 0x4000>; |
| reg-names = "gpmi-nand", "bch"; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "bch"; |
| clocks = <&clks IMX6SX_CLK_GPMI_IO>, |
| <&clks IMX6SX_CLK_GPMI_APB>, |
| <&clks IMX6SX_CLK_GPMI_BCH>, |
| <&clks IMX6SX_CLK_GPMI_BCH_APB>, |
| <&clks IMX6SX_CLK_PER1_BCH>; |
| clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch", |
| "gpmi_bch_apb", "per1_bch"; |
| dmas = <&dma_apbh 0>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| aips1: bus@2000000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02000000 0x100000>; |
| ranges; |
| |
| spba-bus@2000000 { |
| compatible = "fsl,spba-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02000000 0x40000>; |
| ranges; |
| |
| spdif: spdif@2004000 { |
| compatible = "fsl,imx6sx-spdif", "fsl,imx35-spdif"; |
| reg = <0x02004000 0x4000>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 14 18 0>, |
| <&sdma 15 18 0>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks IMX6SX_CLK_SPDIF_GCLK>, |
| <&clks IMX6SX_CLK_OSC>, |
| <&clks IMX6SX_CLK_SPDIF>, |
| <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks IMX6SX_CLK_IPG>, |
| <&clks 0>, <&clks 0>, |
| <&clks IMX6SX_CLK_SPBA>; |
| clock-names = "core", "rxtx0", |
| "rxtx1", "rxtx2", |
| "rxtx3", "rxtx4", |
| "rxtx5", "rxtx6", |
| "rxtx7", "spba"; |
| status = "disabled"; |
| }; |
| |
| ecspi1: spi@2008000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02008000 0x4000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI1>, |
| <&clks IMX6SX_CLK_ECSPI1>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| ecspi2: spi@200c000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x0200c000 0x4000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI2>, |
| <&clks IMX6SX_CLK_ECSPI2>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| ecspi3: spi@2010000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02010000 0x4000>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI3>, |
| <&clks IMX6SX_CLK_ECSPI3>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| ecspi4: spi@2014000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02014000 0x4000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI4>, |
| <&clks IMX6SX_CLK_ECSPI4>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@2020000 { |
| compatible = "fsl,imx6sx-uart", |
| "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x02020000 0x4000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 25 4 0>, <&sdma 26 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| esai: esai@2024000 { |
| compatible = "fsl,imx6sx-esai", "fsl,imx35-esai"; |
| reg = <0x02024000 0x4000>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ESAI_IPG>, |
| <&clks IMX6SX_CLK_ESAI_MEM>, |
| <&clks IMX6SX_CLK_ESAI_EXTAL>, |
| <&clks IMX6SX_CLK_ESAI_IPG>, |
| <&clks IMX6SX_CLK_SPBA>; |
| clock-names = "core", "mem", "extal", |
| "fsys", "spba"; |
| dmas = <&sdma 23 21 0>, |
| <&sdma 24 21 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ssi1: ssi@2028000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6sx-ssi", "fsl,imx51-ssi"; |
| reg = <0x02028000 0x4000>; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SSI1_IPG>, |
| <&clks IMX6SX_CLK_SSI1>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 37 1 0>, <&sdma 38 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| ssi2: ssi@202c000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6sx-ssi", "fsl,imx51-ssi"; |
| reg = <0x0202c000 0x4000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SSI2_IPG>, |
| <&clks IMX6SX_CLK_SSI2>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 41 1 0>, <&sdma 42 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| ssi3: ssi@2030000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6sx-ssi", "fsl,imx51-ssi"; |
| reg = <0x02030000 0x4000>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SSI3_IPG>, |
| <&clks IMX6SX_CLK_SSI3>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 45 1 0>, <&sdma 46 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| asrc: asrc@2034000 { |
| compatible = "fsl,imx6sx-asrc", "fsl,imx53-asrc"; |
| reg = <0x02034000 0x4000>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ASRC_IPG>, |
| <&clks IMX6SX_CLK_ASRC_MEM>, <&clks 0>, |
| <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks IMX6SX_CLK_SPDIF>, <&clks 0>, <&clks 0>, |
| <&clks IMX6SX_CLK_SPBA>; |
| clock-names = "mem", "ipg", "asrck_0", |
| "asrck_1", "asrck_2", "asrck_3", "asrck_4", |
| "asrck_5", "asrck_6", "asrck_7", "asrck_8", |
| "asrck_9", "asrck_a", "asrck_b", "asrck_c", |
| "asrck_d", "asrck_e", "asrck_f", "spba"; |
| dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, |
| <&sdma 19 23 1>, <&sdma 20 23 1>, |
| <&sdma 21 23 1>, <&sdma 22 23 1>; |
| dma-names = "rxa", "rxb", "rxc", |
| "txa", "txb", "txc"; |
| fsl,asrc-rate = <48000>; |
| fsl,asrc-width = <16>; |
| status = "okay"; |
| }; |
| }; |
| |
| pwm1: pwm@2080000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x02080000 0x4000>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM1>, |
| <&clks IMX6SX_CLK_PWM1>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| |
| pwm2: pwm@2084000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x02084000 0x4000>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM2>, |
| <&clks IMX6SX_CLK_PWM2>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| |
| pwm3: pwm@2088000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x02088000 0x4000>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM3>, |
| <&clks IMX6SX_CLK_PWM3>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| |
| pwm4: pwm@208c000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x0208c000 0x4000>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM4>, |
| <&clks IMX6SX_CLK_PWM4>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| |
| flexcan1: can@2090000 { |
| compatible = "fsl,imx6sx-flexcan", "fsl,imx6q-flexcan"; |
| reg = <0x02090000 0x4000>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_CAN1_IPG>, |
| <&clks IMX6SX_CLK_CAN1_SERIAL>; |
| clock-names = "ipg", "per"; |
| fsl,stop-mode = <&gpr 0x10 1>; |
| status = "disabled"; |
| }; |
| |
| flexcan2: can@2094000 { |
| compatible = "fsl,imx6sx-flexcan", "fsl,imx6q-flexcan"; |
| reg = <0x02094000 0x4000>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_CAN2_IPG>, |
| <&clks IMX6SX_CLK_CAN2_SERIAL>; |
| clock-names = "ipg", "per"; |
| fsl,stop-mode = <&gpr 0x10 2>; |
| status = "disabled"; |
| }; |
| |
| gpt: timer@2098000 { |
| compatible = "fsl,imx6sx-gpt", "fsl,imx6dl-gpt"; |
| reg = <0x02098000 0x4000>; |
| interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_GPT_BUS>, |
| <&clks IMX6SX_CLK_GPT_3M>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpio1: gpio@209c000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x0209c000 0x4000>; |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 5 26>; |
| }; |
| |
| gpio2: gpio@20a0000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a0000 0x4000>; |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 31 20>; |
| }; |
| |
| gpio3: gpio@20a4000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a4000 0x4000>; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 51 29>; |
| }; |
| |
| gpio4: gpio@20a8000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a8000 0x4000>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 80 32>; |
| }; |
| |
| gpio5: gpio@20ac000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020ac000 0x4000>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 112 24>; |
| }; |
| |
| gpio6: gpio@20b0000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020b0000 0x4000>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 136 12>, <&iomuxc 12 158 11>; |
| }; |
| |
| gpio7: gpio@20b4000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020b4000 0x4000>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 148 10>, <&iomuxc 10 169 2>; |
| }; |
| |
| kpp: keypad@20b8000 { |
| compatible = "fsl,imx6sx-kpp", "fsl,imx21-kpp"; |
| reg = <0x020b8000 0x4000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| status = "disabled"; |
| }; |
| |
| wdog1: watchdog@20bc000 { |
| compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt"; |
| reg = <0x020bc000 0x4000>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| }; |
| |
| wdog2: watchdog@20c0000 { |
| compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt"; |
| reg = <0x020c0000 0x4000>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| status = "disabled"; |
| }; |
| |
| clks: clock-controller@20c4000 { |
| compatible = "fsl,imx6sx-ccm"; |
| reg = <0x020c4000 0x4000>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; |
| #clock-cells = <1>; |
| clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>, <&anaclk1>, <&anaclk2>; |
| clock-names = "ckil", "osc", "ipp_di0", "ipp_di1", "anaclk1", "anaclk2"; |
| }; |
| |
| anatop: anatop@20c8000 { |
| compatible = "fsl,imx6sx-anatop", "fsl,imx6q-anatop", |
| "syscon", "simple-mfd"; |
| reg = <0x020c8000 0x1000>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; |
| |
| reg_vdd1p1: regulator-1p1 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd1p1"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x110>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <4>; |
| anatop-min-voltage = <800000>; |
| anatop-max-voltage = <1375000>; |
| anatop-enable-bit = <0>; |
| }; |
| |
| reg_vdd3p0: regulator-3p0 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd3p0"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3150000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x120>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <0>; |
| anatop-min-voltage = <2625000>; |
| anatop-max-voltage = <3400000>; |
| anatop-enable-bit = <0>; |
| }; |
| |
| reg_vdd2p5: regulator-2p5 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd2p5"; |
| regulator-min-microvolt = <2250000>; |
| regulator-max-microvolt = <2750000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x130>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <0>; |
| anatop-min-voltage = <2100000>; |
| anatop-max-voltage = <2875000>; |
| anatop-enable-bit = <0>; |
| }; |
| |
| reg_arm: regulator-vddcore { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddarm"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <0>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <24>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| |
| reg_pcie: regulator-vddpcie { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddpcie"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <9>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <26>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| |
| reg_soc: regulator-vddsoc { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddsoc"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <18>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <28>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| |
| tempmon: tempmon { |
| compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon"; |
| interrupt-parent = <&gpc>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,tempmon = <&anatop>; |
| nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>; |
| nvmem-cell-names = "calib", "temp_grade"; |
| clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>; |
| }; |
| }; |
| |
| usbphy1: usbphy@20c9000 { |
| compatible = "fsl,imx6sx-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x020c9000 0x1000>; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBPHY1>; |
| fsl,anatop = <&anatop>; |
| }; |
| |
| usbphy2: usbphy@20ca000 { |
| compatible = "fsl,imx6sx-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x020ca000 0x1000>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBPHY2>; |
| fsl,anatop = <&anatop>; |
| }; |
| |
| snvs: snvs@20cc000 { |
| compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; |
| reg = <0x020cc000 0x4000>; |
| |
| snvs_rtc: snvs-rtc-lp { |
| compatible = "fsl,sec-v4.0-mon-rtc-lp"; |
| regmap = <&snvs>; |
| offset = <0x34>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| snvs_poweroff: snvs-poweroff { |
| compatible = "syscon-poweroff"; |
| regmap = <&snvs>; |
| offset = <0x38>; |
| value = <0x60>; |
| mask = <0x60>; |
| status = "disabled"; |
| }; |
| |
| snvs_pwrkey: snvs-powerkey { |
| compatible = "fsl,sec-v4.0-pwrkey"; |
| regmap = <&snvs>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| linux,keycode = <KEY_POWER>; |
| wakeup-source; |
| status = "disabled"; |
| }; |
| }; |
| |
| epit1: epit@20d0000 { |
| reg = <0x020d0000 0x4000>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| epit2: epit@20d4000 { |
| reg = <0x020d4000 0x4000>; |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| src: reset-controller@20d8000 { |
| compatible = "fsl,imx6sx-src", "fsl,imx51-src"; |
| reg = <0x020d8000 0x4000>; |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| #reset-cells = <1>; |
| }; |
| |
| gpc: gpc@20dc000 { |
| compatible = "fsl,imx6sx-gpc", "fsl,imx6q-gpc"; |
| reg = <0x020dc000 0x4000>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&intc>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| clock-names = "ipg"; |
| |
| pgc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| power-domain@0 { |
| reg = <0>; |
| #power-domain-cells = <0>; |
| }; |
| |
| pd_pu: power-domain@1 { |
| reg = <1>; |
| #power-domain-cells = <0>; |
| power-supply = <®_soc>; |
| clocks = <&clks IMX6SX_CLK_GPU>; |
| }; |
| |
| pd_disp: power-domain@2 { |
| reg = <2>; |
| #power-domain-cells = <0>; |
| clocks = <&clks IMX6SX_CLK_PXP_AXI>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>, |
| <&clks IMX6SX_CLK_LCDIF1_PIX>, |
| <&clks IMX6SX_CLK_LCDIF_APB>, |
| <&clks IMX6SX_CLK_LCDIF2_PIX>, |
| <&clks IMX6SX_CLK_CSI>, |
| <&clks IMX6SX_CLK_VADC>; |
| }; |
| |
| pd_pci: power-domain@3 { |
| reg = <3>; |
| #power-domain-cells = <0>; |
| power-supply = <®_pcie>; |
| }; |
| }; |
| }; |
| |
| iomuxc: pinctrl@20e0000 { |
| compatible = "fsl,imx6sx-iomuxc"; |
| reg = <0x020e0000 0x4000>; |
| }; |
| |
| gpr: iomuxc-gpr@20e4000 { |
| compatible = "fsl,imx6sx-iomuxc-gpr", |
| "fsl,imx6q-iomuxc-gpr", "syscon"; |
| reg = <0x020e4000 0x4000>; |
| }; |
| |
| sdma: dma-controller@20ec000 { |
| compatible = "fsl,imx6sx-sdma", "fsl,imx6q-sdma"; |
| reg = <0x020ec000 0x4000>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>, |
| <&clks IMX6SX_CLK_SDMA>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| /* imx6sx reuses imx6q sdma firmware */ |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin"; |
| }; |
| }; |
| |
| aips2: bus@2100000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02100000 0x100000>; |
| ranges; |
| |
| crypto: crypto@2100000 { |
| compatible = "fsl,sec-v4.0"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x2100000 0x10000>; |
| ranges = <0 0x2100000 0x10000>; |
| interrupt-parent = <&intc>; |
| clocks = <&clks IMX6SX_CLK_CAAM_MEM>, |
| <&clks IMX6SX_CLK_CAAM_ACLK>, |
| <&clks IMX6SX_CLK_CAAM_IPG>, |
| <&clks IMX6SX_CLK_EIM_SLOW>; |
| clock-names = "mem", "aclk", "ipg", "emi_slow"; |
| |
| sec_jr0: jr@1000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x1000 0x1000>; |
| interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr1: jr@2000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x2000 0x1000>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| usbotg1: usb@2184000 { |
| compatible = "fsl,imx6sx-usb", "fsl,imx27-usb"; |
| reg = <0x02184000 0x200>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| fsl,usbphy = <&usbphy1>; |
| fsl,usbmisc = <&usbmisc 0>; |
| fsl,anatop = <&anatop>; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; |
| rx-burst-size-dword = <0x10>; |
| status = "disabled"; |
| }; |
| |
| usbotg2: usb@2184200 { |
| compatible = "fsl,imx6sx-usb", "fsl,imx27-usb"; |
| reg = <0x02184200 0x200>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| fsl,usbphy = <&usbphy2>; |
| fsl,usbmisc = <&usbmisc 1>; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; |
| rx-burst-size-dword = <0x10>; |
| status = "disabled"; |
| }; |
| |
| usbh: usb@2184400 { |
| compatible = "fsl,imx6sx-usb", "fsl,imx27-usb"; |
| reg = <0x02184400 0x200>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| fsl,usbphy = <&usbphynop1>; |
| fsl,usbmisc = <&usbmisc 2>; |
| phy_type = "hsic"; |
| fsl,anatop = <&anatop>; |
| dr_mode = "host"; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; |
| rx-burst-size-dword = <0x10>; |
| status = "disabled"; |
| }; |
| |
| usbmisc: usbmisc@2184800 { |
| #index-cells = <1>; |
| compatible = "fsl,imx6sx-usbmisc", "fsl,imx6q-usbmisc"; |
| reg = <0x02184800 0x200>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| }; |
| |
| fec1: ethernet@2188000 { |
| compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec"; |
| reg = <0x02188000 0x4000>; |
| interrupt-names = "int0", "pps"; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ENET>, |
| <&clks IMX6SX_CLK_ENET_AHB>, |
| <&clks IMX6SX_CLK_ENET_PTP>, |
| <&clks IMX6SX_CLK_ENET_REF>, |
| <&clks IMX6SX_CLK_ENET_PTP>; |
| clock-names = "ipg", "ahb", "ptp", |
| "enet_clk_ref", "enet_out"; |
| fsl,num-tx-queues = <3>; |
| fsl,num-rx-queues = <3>; |
| fsl,stop-mode = <&gpr 0x10 3>; |
| status = "disabled"; |
| }; |
| |
| mlb: mlb@218c000 { |
| reg = <0x0218c000 0x4000>; |
| interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_MLB>; |
| status = "disabled"; |
| }; |
| |
| usdhc1: mmc@2190000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x02190000 0x4000>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC1>, |
| <&clks IMX6SX_CLK_USDHC1>, |
| <&clks IMX6SX_CLK_USDHC1>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| status = "disabled"; |
| }; |
| |
| usdhc2: mmc@2194000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x02194000 0x4000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC2>, |
| <&clks IMX6SX_CLK_USDHC2>, |
| <&clks IMX6SX_CLK_USDHC2>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| status = "disabled"; |
| }; |
| |
| usdhc3: mmc@2198000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x02198000 0x4000>; |
| interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC3>, |
| <&clks IMX6SX_CLK_USDHC3>, |
| <&clks IMX6SX_CLK_USDHC3>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| status = "disabled"; |
| }; |
| |
| usdhc4: mmc@219c000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x0219c000 0x4000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC4>, |
| <&clks IMX6SX_CLK_USDHC4>, |
| <&clks IMX6SX_CLK_USDHC4>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@21a0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a0000 0x4000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C1>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@21a4000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a4000 0x4000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C2>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@21a8000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a8000 0x4000>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C3>; |
| status = "disabled"; |
| }; |
| |
| memory-controller@21b0000 { |
| compatible = "fsl,imx6sx-mmdc", "fsl,imx6q-mmdc"; |
| reg = <0x021b0000 0x4000>; |
| clocks = <&clks IMX6SX_CLK_MMDC_P0_IPG>; |
| }; |
| |
| fec2: ethernet@21b4000 { |
| compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec"; |
| reg = <0x021b4000 0x4000>; |
| interrupt-names = "int0", "pps"; |
| interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ENET>, |
| <&clks IMX6SX_CLK_ENET_AHB>, |
| <&clks IMX6SX_CLK_ENET_PTP>, |
| <&clks IMX6SX_CLK_ENET2_REF_125M>, |
| <&clks IMX6SX_CLK_ENET_PTP>; |
| clock-names = "ipg", "ahb", "ptp", |
| "enet_clk_ref", "enet_out"; |
| fsl,stop-mode = <&gpr 0x10 4>; |
| status = "disabled"; |
| }; |
| |
| weim: weim@21b8000 { |
| #address-cells = <2>; |
| #size-cells = <1>; |
| compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim"; |
| reg = <0x021b8000 0x4000>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_EIM_SLOW>; |
| fsl,weim-cs-gpr = <&gpr>; |
| status = "disabled"; |
| }; |
| |
| ocotp: efuse@21bc000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "fsl,imx6sx-ocotp", "syscon"; |
| reg = <0x021bc000 0x4000>; |
| clocks = <&clks IMX6SX_CLK_OCOTP>; |
| |
| cpu_speed_grade: speed-grade@10 { |
| reg = <0x10 4>; |
| }; |
| |
| tempmon_calib: calib@38 { |
| reg = <0x38 4>; |
| }; |
| |
| tempmon_temp_grade: temp-grade@20 { |
| reg = <0x20 4>; |
| }; |
| }; |
| |
| sai1: sai@21d4000 { |
| compatible = "fsl,imx6sx-sai"; |
| reg = <0x021d4000 0x4000>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SAI1_IPG>, |
| <&clks IMX6SX_CLK_SAI1>, |
| <&clks 0>, <&clks 0>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dma-names = "rx", "tx"; |
| dmas = <&sdma 31 24 0>, <&sdma 32 24 0>; |
| status = "disabled"; |
| }; |
| |
| audmux: audmux@21d8000 { |
| compatible = "fsl,imx6sx-audmux", "fsl,imx31-audmux"; |
| reg = <0x021d8000 0x4000>; |
| status = "disabled"; |
| }; |
| |
| sai2: sai@21dc000 { |
| compatible = "fsl,imx6sx-sai"; |
| reg = <0x021dc000 0x4000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SAI2_IPG>, |
| <&clks IMX6SX_CLK_SAI2>, |
| <&clks 0>, <&clks 0>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dma-names = "rx", "tx"; |
| dmas = <&sdma 33 24 0>, <&sdma 34 24 0>; |
| status = "disabled"; |
| }; |
| |
| qspi1: spi@21e0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-qspi"; |
| reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>; |
| reg-names = "QuadSPI", "QuadSPI-memory"; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_QSPI1>, |
| <&clks IMX6SX_CLK_QSPI1>; |
| clock-names = "qspi_en", "qspi"; |
| status = "disabled"; |
| }; |
| |
| qspi2: spi@21e4000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-qspi"; |
| reg = <0x021e4000 0x4000>, <0x70000000 0x10000000>; |
| reg-names = "QuadSPI", "QuadSPI-memory"; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_QSPI2>, |
| <&clks IMX6SX_CLK_QSPI2>; |
| clock-names = "qspi_en", "qspi"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@21e8000 { |
| compatible = "fsl,imx6sx-uart", |
| "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021e8000 0x4000>; |
| interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 27 4 0>, <&sdma 28 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@21ec000 { |
| compatible = "fsl,imx6sx-uart", |
| "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021ec000 0x4000>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 29 4 0>, <&sdma 30 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@21f0000 { |
| compatible = "fsl,imx6sx-uart", |
| "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021f0000 0x4000>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 31 4 0>, <&sdma 32 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@21f4000 { |
| compatible = "fsl,imx6sx-uart", |
| "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021f4000 0x4000>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 33 4 0>, <&sdma 34 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@21f8000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021f8000 0x4000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C4>; |
| status = "disabled"; |
| }; |
| }; |
| |
| aips3: bus@2200000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02200000 0x100000>; |
| ranges; |
| |
| spba-bus@2240000 { |
| compatible = "fsl,spba-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02240000 0x40000>; |
| ranges; |
| |
| csi1: csi@2214000 { |
| reg = <0x02214000 0x4000>; |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DISPLAY_AXI>, |
| <&clks IMX6SX_CLK_CSI>, |
| <&clks IMX6SX_CLK_DCIC1>; |
| clock-names = "disp-axi", "csi_mclk", "dcic"; |
| status = "disabled"; |
| }; |
| |
| pxp: pxp@2218000 { |
| compatible = "fsl,imx6sx-pxp", "fsl,imx6ull-pxp"; |
| reg = <0x02218000 0x4000>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PXP_AXI>; |
| clock-names = "axi"; |
| power-domains = <&pd_disp>; |
| status = "disabled"; |
| }; |
| |
| csi2: csi@221c000 { |
| reg = <0x0221c000 0x4000>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DISPLAY_AXI>, |
| <&clks IMX6SX_CLK_CSI>, |
| <&clks IMX6SX_CLK_DCIC2>; |
| clock-names = "disp-axi", "csi_mclk", "dcic"; |
| status = "disabled"; |
| }; |
| |
| lcdif1: lcdif@2220000 { |
| compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; |
| reg = <0x02220000 0x4000>; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>, |
| <&clks IMX6SX_CLK_LCDIF_APB>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>; |
| clock-names = "pix", "axi", "disp_axi"; |
| power-domains = <&pd_disp>; |
| status = "disabled"; |
| }; |
| |
| lcdif2: lcdif@2224000 { |
| compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; |
| reg = <0x02224000 0x4000>; |
| interrupts = <GIC_SPI 6 IRQ_TYPE_EDGE_RISING>; |
| clocks = <&clks IMX6SX_CLK_LCDIF2_PIX>, |
| <&clks IMX6SX_CLK_LCDIF_APB>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>; |
| clock-names = "pix", "axi", "disp_axi"; |
| power-domains = <&pd_disp>; |
| status = "disabled"; |
| }; |
| |
| vadc: vadc@2228000 { |
| reg = <0x02228000 0x4000>, <0x0222c000 0x4000>; |
| reg-names = "vadc-vafe", "vadc-vdec"; |
| clocks = <&clks IMX6SX_CLK_VADC>, |
| <&clks IMX6SX_CLK_CSI>; |
| clock-names = "vadc", "csi"; |
| power-domains = <&pd_disp>; |
| status = "disabled"; |
| }; |
| }; |
| |
| adc1: adc@2280000 { |
| compatible = "fsl,imx6sx-adc", "fsl,vf610-adc"; |
| reg = <0x02280000 0x4000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| clock-names = "adc"; |
| fsl,adck-max-frequency = <30000000>, <40000000>, |
| <20000000>; |
| status = "disabled"; |
| }; |
| |
| adc2: adc@2284000 { |
| compatible = "fsl,imx6sx-adc", "fsl,vf610-adc"; |
| reg = <0x02284000 0x4000>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| clock-names = "adc"; |
| fsl,adck-max-frequency = <30000000>, <40000000>, |
| <20000000>; |
| status = "disabled"; |
| }; |
| |
| wdog3: watchdog@2288000 { |
| compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt"; |
| reg = <0x02288000 0x4000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| status = "disabled"; |
| }; |
| |
| ecspi5: spi@228c000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x0228c000 0x4000>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI5>, |
| <&clks IMX6SX_CLK_ECSPI5>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart6: serial@22a0000 { |
| compatible = "fsl,imx6sx-uart", |
| "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x022a0000 0x4000>; |
| interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 0 4 0>, <&sdma 47 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| pwm5: pwm@22a4000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x022a4000 0x4000>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM5>, |
| <&clks IMX6SX_CLK_PWM5>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| |
| pwm6: pwm@22a8000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x022a8000 0x4000>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM6>, |
| <&clks IMX6SX_CLK_PWM6>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| |
| pwm7: pwm@22ac000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x022ac000 0x4000>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM7>, |
| <&clks IMX6SX_CLK_PWM7>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| |
| pwm8: pwm@22b0000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x0022b0000 0x4000>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM8>, |
| <&clks IMX6SX_CLK_PWM8>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <3>; |
| }; |
| }; |
| |
| pcie: pcie@8ffc000 { |
| compatible = "fsl,imx6sx-pcie"; |
| reg = <0x08ffc000 0x04000>, <0x08f00000 0x80000>; |
| reg-names = "dbi", "config"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| bus-range = <0x00 0xff>; |
| ranges = <0x81000000 0 0 0x08f80000 0 0x00010000>, /* downstream I/O */ |
| <0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; /* non-prefetchable memory */ |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PCIE_AXI>, |
| <&clks IMX6SX_CLK_LVDS1_OUT>, |
| <&clks IMX6SX_CLK_PCIE_REF_125M>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>; |
| clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_inbound_axi"; |
| power-domains = <&pd_disp>, <&pd_pci>; |
| power-domain-names = "pcie", "pcie_phy"; |
| status = "disabled"; |
| }; |
| }; |
| }; |
