gpio: sysfs interface
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt
index c35ca9e..8b69811 100644
--- a/Documentation/gpio.txt
+++ b/Documentation/gpio.txt
@@ -347,15 +347,12 @@
Dynamic definition of GPIOs is not currently standard; for example, as
a side effect of configuring an add-on board with some GPIO expanders.
-These calls are purely for kernel space, but a userspace API could be built
-on top of them.
-
GPIO implementor's framework (OPTIONAL)
=======================================
As noted earlier, there is an optional implementation framework making it
easier for platforms to support different kinds of GPIO controller using
-the same programming interface.
+the same programming interface. This framework is called "gpiolib".
As a debugging aid, if debugfs is available a /sys/kernel/debug/gpio file
will be found there. That will list all the controllers registered through
@@ -439,4 +436,120 @@
calls for that GPIO can work. One way to address such dependencies is for
such gpio_chip controllers to provide setup() and teardown() callbacks to
board specific code; those board specific callbacks would register devices
-once all the necessary resources are available.
+once all the necessary resources are available, and remove them later when
+the GPIO controller device becomes unavailable.
+
+
+Sysfs Interface for Userspace (OPTIONAL)
+========================================
+Platforms which use the "gpiolib" implementors framework may choose to
+configure a sysfs user interface to GPIOs. This is different from the
+debugfs interface, since it provides control over GPIO direction and
+value instead of just showing a gpio state summary. Plus, it could be
+present on production systems without debugging support.
+
+Given approprate hardware documentation for the system, userspace could
+know for example that GPIO #23 controls the write protect line used to
+protect boot loader segments in flash memory. System upgrade procedures
+may need to temporarily remove that protection, first importing a GPIO,
+then changing its output state, then updating the code before re-enabling
+the write protection. In normal use, GPIO #23 would never be touched,
+and the kernel would have no need to know about it.
+
+Again depending on appropriate hardware documentation, on some systems
+userspace GPIO can be used to determine system configuration data that
+standard kernels won't know about. And for some tasks, simple userspace
+GPIO drivers could be all that the system really needs.
+
+Note that standard kernel drivers exist for common "LEDs and Buttons"
+GPIO tasks: "leds-gpio" and "gpio_keys", respectively. Use those
+instead of talking directly to the GPIOs; they integrate with kernel
+frameworks better than your userspace code could.
+
+
+Paths in Sysfs
+--------------
+There are three kinds of entry in /sys/class/gpio:
+
+ - Control interfaces used to get userspace control over GPIOs;
+
+ - GPIOs themselves; and
+
+ - GPIO controllers ("gpio_chip" instances).
+
+That's in addition to standard files including the "device" symlink.
+
+The control interfaces are write-only:
+
+ /sys/class/gpio/
+
+ "export" ... Userspace may ask the kernel to export control of
+ a GPIO to userspace by writing its number to this file.
+
+ Example: "echo 19 > export" will create a "gpio19" node
+ for GPIO #19, if that's not requested by kernel code.
+
+ "unexport" ... Reverses the effect of exporting to userspace.
+
+ Example: "echo 19 > unexport" will remove a "gpio19"
+ node exported using the "export" file.
+
+GPIO signals have paths like /sys/class/gpio/gpio42/ (for GPIO #42)
+and have the following read/write attributes:
+
+ /sys/class/gpio/gpioN/
+
+ "direction" ... reads as either "in" or "out". This value may
+ normally be written. Writing as "out" defaults to
+ initializing the value as low. To ensure glitch free
+ operation, values "low" and "high" may be written to
+ configure the GPIO as an output with that initial value.
+
+ Note that this attribute *will not exist* if the kernel
+ doesn't support changing the direction of a GPIO, or
+ it was exported by kernel code that didn't explicitly
+ allow userspace to reconfigure this GPIO's direction.
+
+ "value" ... reads as either 0 (low) or 1 (high). If the GPIO
+ is configured as an output, this value may be written;
+ any nonzero value is treated as high.
+
+GPIO controllers have paths like /sys/class/gpio/chipchip42/ (for the
+controller implementing GPIOs starting at #42) and have the following
+read-only attributes:
+
+ /sys/class/gpio/gpiochipN/
+
+ "base" ... same as N, the first GPIO managed by this chip
+
+ "label" ... provided for diagnostics (not always unique)
+
+ "ngpio" ... how many GPIOs this manges (N to N + ngpio - 1)
+
+Board documentation should in most cases cover what GPIOs are used for
+what purposes. However, those numbers are not always stable; GPIOs on
+a daughtercard might be different depending on the base board being used,
+or other cards in the stack. In such cases, you may need to use the
+gpiochip nodes (possibly in conjunction with schematics) to determine
+the correct GPIO number to use for a given signal.
+
+
+Exporting from Kernel code
+--------------------------
+Kernel code can explicitly manage exports of GPIOs which have already been
+requested using gpio_request():
+
+ /* export the GPIO to userspace */
+ int gpio_export(unsigned gpio, bool direction_may_change);
+
+ /* reverse gpio_export() */
+ void gpio_unexport();
+
+After a kernel driver requests a GPIO, it may only be made available in
+the sysfs interface by gpio_export(). The driver can control whether the
+signal direction may change. This helps drivers prevent userspace code
+from accidentally clobbering important system state.
+
+This explicit exporting can help with debugging (by making some kinds
+of experiments easier), or can provide an always-there interface that's
+suitable for documenting as part of a board support package.
