spi: zynq-qspi: Clarify the select chip function
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c
index 70ecefd..80e51c8 100644
--- a/drivers/spi/spi-zynq-qspi.c
+++ b/drivers/spi/spi-zynq-qspi.c
@@ -50,7 +50,6 @@
#define ZYNQ_QSPI_CONFIG_BDRATE_MASK GENMASK(5, 3) /* Baud Rate Mask */
#define ZYNQ_QSPI_CONFIG_CPHA_MASK BIT(2) /* Clock Phase Control */
#define ZYNQ_QSPI_CONFIG_CPOL_MASK BIT(1) /* Clock Polarity Control */
-#define ZYNQ_QSPI_CONFIG_SSCTRL_MASK BIT(10) /* Slave Select Mask */
#define ZYNQ_QSPI_CONFIG_FWIDTH_MASK GENMASK(7, 6) /* FIFO width */
#define ZYNQ_QSPI_CONFIG_MSTREN_MASK BIT(0) /* Master Mode */
@@ -62,7 +61,7 @@
*/
#define ZYNQ_QSPI_CONFIG_BAUD_DIV_MAX GENMASK(2, 0) /* Baud rate maximum */
#define ZYNQ_QSPI_CONFIG_BAUD_DIV_SHIFT 3 /* Baud rate divisor shift */
-#define ZYNQ_QSPI_CONFIG_PCS 10 /* Peripheral Chip Select */
+#define ZYNQ_QSPI_CONFIG_PCS BIT(10) /* Peripheral Chip Select */
/*
* QSPI Interrupt Registers bit Masks
@@ -287,16 +286,12 @@ static void zynq_qspi_chipselect(struct spi_device *spi, bool assert)
struct zynq_qspi *xqspi = spi_controller_get_devdata(ctlr);
u32 config_reg;
+ /* Ground the line to assert the CS */
config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_CONFIG_OFFSET);
- if (assert) {
- /* Select the slave */
- config_reg &= ~ZYNQ_QSPI_CONFIG_SSCTRL_MASK;
- config_reg |= (((~(BIT(spi->chip_select))) <<
- ZYNQ_QSPI_CONFIG_PCS) &
- ZYNQ_QSPI_CONFIG_SSCTRL_MASK);
- } else {
- config_reg |= ZYNQ_QSPI_CONFIG_SSCTRL_MASK;
- }
+ if (assert)
+ config_reg &= ~ZYNQ_QSPI_CONFIG_PCS;
+ else
+ config_reg |= ZYNQ_QSPI_CONFIG_PCS;
zynq_qspi_write(xqspi, ZYNQ_QSPI_CONFIG_OFFSET, config_reg);
}
