diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 2ed5333..027ee37 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -36,7 +36,7 @@
 #define DRIVER_AUTHOR	"WOOJUNG HUH <woojung.huh@microchip.com>"
 #define DRIVER_DESC	"LAN78XX USB 3.0 Gigabit Ethernet Devices"
 #define DRIVER_NAME	"lan78xx"
-#define DRIVER_VERSION	"1.0.1"
+#define DRIVER_VERSION	"1.0.2"
 
 #define TX_TIMEOUT_JIFFIES		(5 * HZ)
 #define THROTTLE_JIFFIES		(HZ / 8)
@@ -904,7 +904,6 @@
 
 	if (!phydev->link && dev->link_on) {
 		dev->link_on = false;
-		netif_carrier_off(dev->net);
 
 		/* reset MAC */
 		ret = lan78xx_read_reg(dev, MAC_CR, &buf);
@@ -914,6 +913,8 @@
 		ret = lan78xx_write_reg(dev, MAC_CR, buf);
 		if (unlikely(ret < 0))
 			return -EIO;
+
+		phy_mac_interrupt(phydev, 0);
 	} else if (phydev->link && !dev->link_on) {
 		dev->link_on = true;
 
@@ -953,7 +954,7 @@
 			  ethtool_cmd_speed(&ecmd), ecmd.duplex, ladv, radv);
 
 		ret = lan78xx_update_flowcontrol(dev, ecmd.duplex, ladv, radv);
-		netif_carrier_on(dev->net);
+		phy_mac_interrupt(phydev, 1);
 	}
 
 	return ret;
@@ -1495,7 +1496,6 @@
 static int lan78xx_mdio_init(struct lan78xx_net *dev)
 {
 	int ret;
-	int i;
 
 	dev->mdiobus = mdiobus_alloc();
 	if (!dev->mdiobus) {
@@ -1511,10 +1511,6 @@
 	snprintf(dev->mdiobus->id, MII_BUS_ID_SIZE, "usb-%03d:%03d",
 		 dev->udev->bus->busnum, dev->udev->devnum);
 
-	/* handle our own interrupt */
-	for (i = 0; i < PHY_MAX_ADDR; i++)
-		dev->mdiobus->irq[i] = PHY_IGNORE_INTERRUPT;
-
 	switch (dev->devid & ID_REV_CHIP_ID_MASK_) {
 	case 0x78000000:
 	case 0x78500000:
@@ -1558,6 +1554,16 @@
 		return -EIO;
 	}
 
+	/* Enable PHY interrupts.
+	 * We handle our own interrupt
+	 */
+	ret = phy_read(phydev, LAN88XX_INT_STS);
+	ret = phy_write(phydev, LAN88XX_INT_MASK,
+			LAN88XX_INT_MASK_MDINTPIN_EN_ |
+			LAN88XX_INT_MASK_LINK_CHANGE_);
+
+	phydev->irq = PHY_IGNORE_INTERRUPT;
+
 	ret = phy_connect_direct(dev->net, phydev,
 				 lan78xx_link_status_change,
 				 PHY_INTERFACE_MODE_GMII);
@@ -1580,14 +1586,6 @@
 			      SUPPORTED_Pause | SUPPORTED_Asym_Pause);
 	genphy_config_aneg(phydev);
 
-	/* Workaround to enable PHY interrupt.
-	 * phy_start_interrupts() is API for requesting and enabling
-	 * PHY interrupt. However, USB-to-Ethernet device can't use
-	 * request_irq() called in phy_start_interrupts().
-	 * Set PHY to PHY_HALTED and call phy_start()
-	 * to make a call to phy_enable_interrupts()
-	 */
-	phy_stop(phydev);
 	phy_start(phydev);
 
 	netif_dbg(dev, ifup, dev->net, "phy initialised successfully");