* Qualcomm NAND controller

Required properties:
- compatible:		must be one of the following:
    * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
			    SoC and it uses ADM DMA
    * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
                            IPQ4019 SoC and it uses BAM DMA
    * "qcom,ipq6018-nand" - for QPIC NAND controller v1.5.0 being used in
                            IPQ6018 SoC and it uses BAM DMA
    * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in
                            IPQ8074 SoC and it uses BAM DMA
    * "qcom,sdx55-nand"   - for QPIC NAND controller v2.0.0 being used in
                            SDX55 SoC and it uses BAM DMA

- reg:			MMIO address range
- clocks:		must contain core clock and always on clock
- clock-names:		must contain "core" for the core clock and "aon" for the
			always on clock

EBI2 specific properties:
- dmas:			DMA specifier, consisting of a phandle to the ADM DMA
			controller node and the channel number to be used for
			NAND. Refer to dma.txt and qcom_adm.txt for more details
- dma-names:		must be "rxtx"
- qcom,cmd-crci:	must contain the ADM command type CRCI block instance
			number specified for the NAND controller on the given
			platform
- qcom,data-crci:	must contain the ADM data type CRCI block instance
			number specified for the NAND controller on the given
			platform

QPIC specific properties:
- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
			and the channel number to be used for NAND. Refer to
			dma.txt, qcom_bam_dma.txt for more details
- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
- #address-cells:	<1> - subnodes give the chip-select number
- #size-cells:		<0>

* NAND chip-select

Each controller may contain one or more subnodes to represent enabled
chip-selects which (may) contain NAND flash chips. Their properties are as
follows.

Required properties:
- reg:			a single integer representing the chip-select
			number (e.g., 0, 1, 2, etc.)
- #address-cells:	see partition.txt
- #size-cells:		see partition.txt

Optional properties:
- nand-bus-width:	see nand-controller.yaml
- nand-ecc-strength:	see nand-controller.yaml. If not specified, then ECC strength will
			be used according to chip requirement and available
			OOB size.

Each nandcs device node may optionally contain a 'partitions' sub-node, which
further contains sub-nodes describing the flash partition mapping. See
partition.txt for more detail.

Example:

nand-controller@1ac00000 {
	compatible = "qcom,ipq806x-nand";
	reg = <0x1ac00000 0x800>;

	clocks = <&gcc EBI2_CLK>,
		 <&gcc EBI2_AON_CLK>;
	clock-names = "core", "aon";

	dmas = <&adm_dma 3>;
	dma-names = "rxtx";
	qcom,cmd-crci = <15>;
	qcom,data-crci = <3>;

	#address-cells = <1>;
	#size-cells = <0>;

	nand@0 {
		reg = <0>;

		nand-ecc-strength = <4>;
		nand-bus-width = <8>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "boot-nand";
				reg = <0 0x58a0000>;
			};

			partition@58a0000 {
				label = "fs-nand";
				reg = <0x58a0000 0x4000000>;
			};
		};
	};
};

nand-controller@79b0000 {
	compatible = "qcom,ipq4019-nand";
	reg = <0x79b0000 0x1000>;

	clocks = <&gcc GCC_QPIC_CLK>,
		<&gcc GCC_QPIC_AHB_CLK>;
	clock-names = "core", "aon";

	dmas = <&qpicbam 0>,
		<&qpicbam 1>,
		<&qpicbam 2>;
	dma-names = "tx", "rx", "cmd";

	#address-cells = <1>;
	#size-cells = <0>;

	nand@0 {
		reg = <0>;
		nand-ecc-strength = <4>;
		nand-bus-width = <8>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "boot-nand";
				reg = <0 0x58a0000>;
			};

			partition@58a0000 {
				label = "fs-nand";
				reg = <0x58a0000 0x4000000>;
			};
		};
	};
};