// SPDX-License-Identifier: GPL-2.0
/*
 * SDM845 SoC device tree source
 *
 * Copyright (c) 2018, The Linux Foundation. All rights reserved.
 */

#include <dt-bindings/clock/qcom,camcc-sdm845.h>
#include <dt-bindings/clock/qcom,dispcc-sdm845.h>
#include <dt-bindings/clock/qcom,gcc-sdm845.h>
#include <dt-bindings/clock/qcom,gpucc-sdm845.h>
#include <dt-bindings/clock/qcom,lpass-sdm845.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/clock/qcom,videocc-sdm845.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sdm845.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/phy/phy-qcom-qusb2.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/reset/qcom,sdm845-aoss.h>
#include <dt-bindings/reset/qcom,sdm845-pdc.h>
#include <dt-bindings/soc/qcom,apr.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/clock/qcom,gcc-sdm845.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	aliases {
		i2c0 = &i2c0;
		i2c1 = &i2c1;
		i2c2 = &i2c2;
		i2c3 = &i2c3;
		i2c4 = &i2c4;
		i2c5 = &i2c5;
		i2c6 = &i2c6;
		i2c7 = &i2c7;
		i2c8 = &i2c8;
		i2c9 = &i2c9;
		i2c10 = &i2c10;
		i2c11 = &i2c11;
		i2c12 = &i2c12;
		i2c13 = &i2c13;
		i2c14 = &i2c14;
		i2c15 = &i2c15;
		spi0 = &spi0;
		spi1 = &spi1;
		spi2 = &spi2;
		spi3 = &spi3;
		spi4 = &spi4;
		spi5 = &spi5;
		spi6 = &spi6;
		spi7 = &spi7;
		spi8 = &spi8;
		spi9 = &spi9;
		spi10 = &spi10;
		spi11 = &spi11;
		spi12 = &spi12;
		spi13 = &spi13;
		spi14 = &spi14;
		spi15 = &spi15;
	};

	chosen { };

	clocks {
		xo_board: xo-board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <38400000>;
			clock-output-names = "xo_board";
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32764>;
		};
	};

	cpus: cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x0>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <611>;
			dynamic-power-coefficient = <154>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD0>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			next-level-cache = <&L2_0>;
			L2_0: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
				L3_0: l3-cache {
					compatible = "cache";
					cache-level = <3>;
					cache-unified;
				};
			};
		};

		CPU1: cpu@100 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x100>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <611>;
			dynamic-power-coefficient = <154>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD1>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			next-level-cache = <&L2_100>;
			L2_100: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU2: cpu@200 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x200>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <611>;
			dynamic-power-coefficient = <154>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD2>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			next-level-cache = <&L2_200>;
			L2_200: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU3: cpu@300 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x300>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			capacity-dmips-mhz = <611>;
			dynamic-power-coefficient = <154>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			power-domains = <&CPU_PD3>;
			power-domain-names = "psci";
			next-level-cache = <&L2_300>;
			L2_300: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU4: cpu@400 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x400>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <442>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD4>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			next-level-cache = <&L2_400>;
			L2_400: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU5: cpu@500 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x500>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <442>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD5>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			next-level-cache = <&L2_500>;
			L2_500: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU6: cpu@600 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x600>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <442>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD6>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			next-level-cache = <&L2_600>;
			L2_600: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU7: cpu@700 {
			device_type = "cpu";
			compatible = "qcom,kryo385";
			reg = <0x0 0x700>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <442>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD7>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			next-level-cache = <&L2_700>;
			L2_700: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};

				core2 {
					cpu = <&CPU2>;
				};

				core3 {
					cpu = <&CPU3>;
				};

				core4 {
					cpu = <&CPU4>;
				};

				core5 {
					cpu = <&CPU5>;
				};

				core6 {
					cpu = <&CPU6>;
				};

				core7 {
					cpu = <&CPU7>;
				};
			};
		};

		cpu_idle_states: idle-states {
			entry-method = "psci";

			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
				compatible = "arm,idle-state";
				idle-state-name = "little-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <350>;
				exit-latency-us = <461>;
				min-residency-us = <1890>;
				local-timer-stop;
			};

			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
				compatible = "arm,idle-state";
				idle-state-name = "big-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <264>;
				exit-latency-us = <621>;
				min-residency-us = <952>;
				local-timer-stop;
			};
		};

		domain-idle-states {
			CLUSTER_SLEEP_0: cluster-sleep-0 {
				compatible = "domain-idle-state";
				arm,psci-suspend-param = <0x4100c244>;
				entry-latency-us = <3263>;
				exit-latency-us = <6562>;
				min-residency-us = <9987>;
			};
		};
	};

	firmware {
		scm {
			compatible = "qcom,scm-sdm845", "qcom,scm";
		};
	};

	memory@80000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0 0x80000000 0 0>;
	};

	cpu0_opp_table: opp-table-cpu0 {
		compatible = "operating-points-v2";
		opp-shared;

		cpu0_opp1: opp-300000000 {
			opp-hz = /bits/ 64 <300000000>;
			opp-peak-kBps = <800000 4800000>;
		};

		cpu0_opp2: opp-403200000 {
			opp-hz = /bits/ 64 <403200000>;
			opp-peak-kBps = <800000 4800000>;
		};

		cpu0_opp3: opp-480000000 {
			opp-hz = /bits/ 64 <480000000>;
			opp-peak-kBps = <800000 6451200>;
		};

		cpu0_opp4: opp-576000000 {
			opp-hz = /bits/ 64 <576000000>;
			opp-peak-kBps = <800000 6451200>;
		};

		cpu0_opp5: opp-652800000 {
			opp-hz = /bits/ 64 <652800000>;
			opp-peak-kBps = <800000 7680000>;
		};

		cpu0_opp6: opp-748800000 {
			opp-hz = /bits/ 64 <748800000>;
			opp-peak-kBps = <1804000 9216000>;
		};

		cpu0_opp7: opp-825600000 {
			opp-hz = /bits/ 64 <825600000>;
			opp-peak-kBps = <1804000 9216000>;
		};

		cpu0_opp8: opp-902400000 {
			opp-hz = /bits/ 64 <902400000>;
			opp-peak-kBps = <1804000 10444800>;
		};

		cpu0_opp9: opp-979200000 {
			opp-hz = /bits/ 64 <979200000>;
			opp-peak-kBps = <1804000 11980800>;
		};

		cpu0_opp10: opp-1056000000 {
			opp-hz = /bits/ 64 <1056000000>;
			opp-peak-kBps = <1804000 11980800>;
		};

		cpu0_opp11: opp-1132800000 {
			opp-hz = /bits/ 64 <1132800000>;
			opp-peak-kBps = <2188000 13516800>;
		};

		cpu0_opp12: opp-1228800000 {
			opp-hz = /bits/ 64 <1228800000>;
			opp-peak-kBps = <2188000 15052800>;
		};

		cpu0_opp13: opp-1324800000 {
			opp-hz = /bits/ 64 <1324800000>;
			opp-peak-kBps = <2188000 16588800>;
		};

		cpu0_opp14: opp-1420800000 {
			opp-hz = /bits/ 64 <1420800000>;
			opp-peak-kBps = <3072000 18124800>;
		};

		cpu0_opp15: opp-1516800000 {
			opp-hz = /bits/ 64 <1516800000>;
			opp-peak-kBps = <3072000 19353600>;
		};

		cpu0_opp16: opp-1612800000 {
			opp-hz = /bits/ 64 <1612800000>;
			opp-peak-kBps = <4068000 19353600>;
		};

		cpu0_opp17: opp-1689600000 {
			opp-hz = /bits/ 64 <1689600000>;
			opp-peak-kBps = <4068000 20889600>;
		};

		cpu0_opp18: opp-1766400000 {
			opp-hz = /bits/ 64 <1766400000>;
			opp-peak-kBps = <4068000 22425600>;
		};
	};

	cpu4_opp_table: opp-table-cpu4 {
		compatible = "operating-points-v2";
		opp-shared;

		cpu4_opp1: opp-300000000 {
			opp-hz = /bits/ 64 <300000000>;
			opp-peak-kBps = <800000 4800000>;
		};

		cpu4_opp2: opp-403200000 {
			opp-hz = /bits/ 64 <403200000>;
			opp-peak-kBps = <800000 4800000>;
		};

		cpu4_opp3: opp-480000000 {
			opp-hz = /bits/ 64 <480000000>;
			opp-peak-kBps = <1804000 4800000>;
		};

		cpu4_opp4: opp-576000000 {
			opp-hz = /bits/ 64 <576000000>;
			opp-peak-kBps = <1804000 4800000>;
		};

		cpu4_opp5: opp-652800000 {
			opp-hz = /bits/ 64 <652800000>;
			opp-peak-kBps = <1804000 4800000>;
		};

		cpu4_opp6: opp-748800000 {
			opp-hz = /bits/ 64 <748800000>;
			opp-peak-kBps = <1804000 4800000>;
		};

		cpu4_opp7: opp-825600000 {
			opp-hz = /bits/ 64 <825600000>;
			opp-peak-kBps = <2188000 9216000>;
		};

		cpu4_opp8: opp-902400000 {
			opp-hz = /bits/ 64 <902400000>;
			opp-peak-kBps = <2188000 9216000>;
		};

		cpu4_opp9: opp-979200000 {
			opp-hz = /bits/ 64 <979200000>;
			opp-peak-kBps = <2188000 9216000>;
		};

		cpu4_opp10: opp-1056000000 {
			opp-hz = /bits/ 64 <1056000000>;
			opp-peak-kBps = <3072000 9216000>;
		};

		cpu4_opp11: opp-1132800000 {
			opp-hz = /bits/ 64 <1132800000>;
			opp-peak-kBps = <3072000 11980800>;
		};

		cpu4_opp12: opp-1209600000 {
			opp-hz = /bits/ 64 <1209600000>;
			opp-peak-kBps = <4068000 11980800>;
		};

		cpu4_opp13: opp-1286400000 {
			opp-hz = /bits/ 64 <1286400000>;
			opp-peak-kBps = <4068000 11980800>;
		};

		cpu4_opp14: opp-1363200000 {
			opp-hz = /bits/ 64 <1363200000>;
			opp-peak-kBps = <4068000 15052800>;
		};

		cpu4_opp15: opp-1459200000 {
			opp-hz = /bits/ 64 <1459200000>;
			opp-peak-kBps = <4068000 15052800>;
		};

		cpu4_opp16: opp-1536000000 {
			opp-hz = /bits/ 64 <1536000000>;
			opp-peak-kBps = <5412000 15052800>;
		};

		cpu4_opp17: opp-1612800000 {
			opp-hz = /bits/ 64 <1612800000>;
			opp-peak-kBps = <5412000 15052800>;
		};

		cpu4_opp18: opp-1689600000 {
			opp-hz = /bits/ 64 <1689600000>;
			opp-peak-kBps = <5412000 19353600>;
		};

		cpu4_opp19: opp-1766400000 {
			opp-hz = /bits/ 64 <1766400000>;
			opp-peak-kBps = <6220000 19353600>;
		};

		cpu4_opp20: opp-1843200000 {
			opp-hz = /bits/ 64 <1843200000>;
			opp-peak-kBps = <6220000 19353600>;
		};

		cpu4_opp21: opp-1920000000 {
			opp-hz = /bits/ 64 <1920000000>;
			opp-peak-kBps = <7216000 19353600>;
		};

		cpu4_opp22: opp-1996800000 {
			opp-hz = /bits/ 64 <1996800000>;
			opp-peak-kBps = <7216000 20889600>;
		};

		cpu4_opp23: opp-2092800000 {
			opp-hz = /bits/ 64 <2092800000>;
			opp-peak-kBps = <7216000 20889600>;
		};

		cpu4_opp24: opp-2169600000 {
			opp-hz = /bits/ 64 <2169600000>;
			opp-peak-kBps = <7216000 20889600>;
		};

		cpu4_opp25: opp-2246400000 {
			opp-hz = /bits/ 64 <2246400000>;
			opp-peak-kBps = <7216000 20889600>;
		};

		cpu4_opp26: opp-2323200000 {
			opp-hz = /bits/ 64 <2323200000>;
			opp-peak-kBps = <7216000 20889600>;
		};

		cpu4_opp27: opp-2400000000 {
			opp-hz = /bits/ 64 <2400000000>;
			opp-peak-kBps = <7216000 22425600>;
		};

		cpu4_opp28: opp-2476800000 {
			opp-hz = /bits/ 64 <2476800000>;
			opp-peak-kBps = <7216000 22425600>;
		};

		cpu4_opp29: opp-2553600000 {
			opp-hz = /bits/ 64 <2553600000>;
			opp-peak-kBps = <7216000 22425600>;
		};

		cpu4_opp30: opp-2649600000 {
			opp-hz = /bits/ 64 <2649600000>;
			opp-peak-kBps = <7216000 22425600>;
		};

		cpu4_opp31: opp-2745600000 {
			opp-hz = /bits/ 64 <2745600000>;
			opp-peak-kBps = <7216000 25497600>;
		};

		cpu4_opp32: opp-2803200000 {
			opp-hz = /bits/ 64 <2803200000>;
			opp-peak-kBps = <7216000 25497600>;
		};
	};

	dsi_opp_table: opp-table-dsi {
		compatible = "operating-points-v2";

		opp-19200000 {
			opp-hz = /bits/ 64 <19200000>;
			required-opps = <&rpmhpd_opp_min_svs>;
		};

		opp-180000000 {
			opp-hz = /bits/ 64 <180000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-275000000 {
			opp-hz = /bits/ 64 <275000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};

		opp-328580000 {
			opp-hz = /bits/ 64 <328580000>;
			required-opps = <&rpmhpd_opp_svs_l1>;
		};

		opp-358000000 {
			opp-hz = /bits/ 64 <358000000>;
			required-opps = <&rpmhpd_opp_nom>;
		};
	};

	qspi_opp_table: opp-table-qspi {
		compatible = "operating-points-v2";

		opp-19200000 {
			opp-hz = /bits/ 64 <19200000>;
			required-opps = <&rpmhpd_opp_min_svs>;
		};

		opp-100000000 {
			opp-hz = /bits/ 64 <100000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-150000000 {
			opp-hz = /bits/ 64 <150000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};

		opp-300000000 {
			opp-hz = /bits/ 64 <300000000>;
			required-opps = <&rpmhpd_opp_nom>;
		};
	};

	qup_opp_table: opp-table-qup {
		compatible = "operating-points-v2";

		opp-50000000 {
			opp-hz = /bits/ 64 <50000000>;
			required-opps = <&rpmhpd_opp_min_svs>;
		};

		opp-75000000 {
			opp-hz = /bits/ 64 <75000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-100000000 {
			opp-hz = /bits/ 64 <100000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};

		opp-128000000 {
			opp-hz = /bits/ 64 <128000000>;
			required-opps = <&rpmhpd_opp_nom>;
		};
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>;
	};

	psci: psci {
		compatible = "arm,psci-1.0";
		method = "smc";

		CPU_PD0: power-domain-cpu0 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD1: power-domain-cpu1 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD2: power-domain-cpu2 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD3: power-domain-cpu3 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD4: power-domain-cpu4 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD5: power-domain-cpu5 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD6: power-domain-cpu6 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD7: power-domain-cpu7 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CLUSTER_PD: power-domain-cluster {
			#power-domain-cells = <0>;
			domain-idle-states = <&CLUSTER_SLEEP_0>;
		};
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		hyp_mem: hyp-mem@85700000 {
			reg = <0 0x85700000 0 0x600000>;
			no-map;
		};

		xbl_mem: xbl-mem@85e00000 {
			reg = <0 0x85e00000 0 0x100000>;
			no-map;
		};

		aop_mem: aop-mem@85fc0000 {
			reg = <0 0x85fc0000 0 0x20000>;
			no-map;
		};

		aop_cmd_db_mem: aop-cmd-db-mem@85fe0000 {
			compatible = "qcom,cmd-db";
			reg = <0x0 0x85fe0000 0 0x20000>;
			no-map;
		};

		smem@86000000 {
			compatible = "qcom,smem";
			reg = <0x0 0x86000000 0 0x200000>;
			no-map;
			hwlocks = <&tcsr_mutex 3>;
		};

		tz_mem: tz@86200000 {
			reg = <0 0x86200000 0 0x2d00000>;
			no-map;
		};

		rmtfs_mem: rmtfs@88f00000 {
			compatible = "qcom,rmtfs-mem";
			reg = <0 0x88f00000 0 0x200000>;
			no-map;

			qcom,client-id = <1>;
			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
		};

		qseecom_mem: qseecom@8ab00000 {
			reg = <0 0x8ab00000 0 0x1400000>;
			no-map;
		};

		camera_mem: camera-mem@8bf00000 {
			reg = <0 0x8bf00000 0 0x500000>;
			no-map;
		};

		ipa_fw_mem: ipa-fw@8c400000 {
			reg = <0 0x8c400000 0 0x10000>;
			no-map;
		};

		ipa_gsi_mem: ipa-gsi@8c410000 {
			reg = <0 0x8c410000 0 0x5000>;
			no-map;
		};

		gpu_mem: gpu@8c415000 {
			reg = <0 0x8c415000 0 0x2000>;
			no-map;
		};

		adsp_mem: adsp@8c500000 {
			reg = <0 0x8c500000 0 0x1a00000>;
			no-map;
		};

		wlan_msa_mem: wlan-msa@8df00000 {
			reg = <0 0x8df00000 0 0x100000>;
			no-map;
		};

		mpss_region: mpss@8e000000 {
			reg = <0 0x8e000000 0 0x7800000>;
			no-map;
		};

		venus_mem: venus@95800000 {
			reg = <0 0x95800000 0 0x500000>;
			no-map;
		};

		cdsp_mem: cdsp@95d00000 {
			reg = <0 0x95d00000 0 0x800000>;
			no-map;
		};

		mba_region: mba@96500000 {
			reg = <0 0x96500000 0 0x200000>;
			no-map;
		};

		slpi_mem: slpi@96700000 {
			reg = <0 0x96700000 0 0x1400000>;
			no-map;
		};

		spss_mem: spss@97b00000 {
			reg = <0 0x97b00000 0 0x100000>;
			no-map;
		};

		mdata_mem: mpss-metadata {
			alloc-ranges = <0 0xa0000000 0 0x20000000>;
			size = <0 0x4000>;
			no-map;
		};

		fastrpc_mem: fastrpc {
			compatible = "shared-dma-pool";
			alloc-ranges = <0x0 0x00000000 0x0 0xffffffff>;
			alignment = <0x0 0x400000>;
			size = <0x0 0x1000000>;
			reusable;
		};
	};

	adsp_pas: remoteproc-adsp {
		compatible = "qcom,sdm845-adsp-pas";

		interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
				      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
				      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
				      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
				      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
		interrupt-names = "wdog", "fatal", "ready",
				  "handover", "stop-ack";

		clocks = <&rpmhcc RPMH_CXO_CLK>;
		clock-names = "xo";

		memory-region = <&adsp_mem>;

		qcom,qmp = <&aoss_qmp>;

		qcom,smem-states = <&adsp_smp2p_out 0>;
		qcom,smem-state-names = "stop";

		status = "disabled";

		glink-edge {
			interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
			label = "lpass";
			qcom,remote-pid = <2>;
			mboxes = <&apss_shared 8>;

			apr {
				compatible = "qcom,apr-v2";
				qcom,glink-channels = "apr_audio_svc";
				qcom,domain = <APR_DOMAIN_ADSP>;
				#address-cells = <1>;
				#size-cells = <0>;
				qcom,intents = <512 20>;

				service@3 {
					reg = <APR_SVC_ADSP_CORE>;
					compatible = "qcom,q6core";
					qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
				};

				q6afe: service@4 {
					compatible = "qcom,q6afe";
					reg = <APR_SVC_AFE>;
					qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
					q6afedai: dais {
						compatible = "qcom,q6afe-dais";
						#address-cells = <1>;
						#size-cells = <0>;
						#sound-dai-cells = <1>;
					};
				};

				q6asm: service@7 {
					compatible = "qcom,q6asm";
					reg = <APR_SVC_ASM>;
					qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
					q6asmdai: dais {
						compatible = "qcom,q6asm-dais";
						#address-cells = <1>;
						#size-cells = <0>;
						#sound-dai-cells = <1>;
						iommus = <&apps_smmu 0x1821 0x0>;
					};
				};

				q6adm: service@8 {
					compatible = "qcom,q6adm";
					reg = <APR_SVC_ADM>;
					qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
					q6routing: routing {
						compatible = "qcom,q6adm-routing";
						#sound-dai-cells = <0>;
					};
				};
			};

			fastrpc {
				compatible = "qcom,fastrpc";
				qcom,glink-channels = "fastrpcglink-apps-dsp";
				label = "adsp";
				qcom,non-secure-domain;
				#address-cells = <1>;
				#size-cells = <0>;

				compute-cb@3 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <3>;
					iommus = <&apps_smmu 0x1823 0x0>;
				};

				compute-cb@4 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <4>;
					iommus = <&apps_smmu 0x1824 0x0>;
				};
			};
		};
	};

	cdsp_pas: remoteproc-cdsp {
		compatible = "qcom,sdm845-cdsp-pas";

		interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
				      <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
				      <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
				      <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
				      <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
		interrupt-names = "wdog", "fatal", "ready",
				  "handover", "stop-ack";

		clocks = <&rpmhcc RPMH_CXO_CLK>;
		clock-names = "xo";

		memory-region = <&cdsp_mem>;

		qcom,qmp = <&aoss_qmp>;

		qcom,smem-states = <&cdsp_smp2p_out 0>;
		qcom,smem-state-names = "stop";

		status = "disabled";

		glink-edge {
			interrupts = <GIC_SPI 574 IRQ_TYPE_EDGE_RISING>;
			label = "turing";
			qcom,remote-pid = <5>;
			mboxes = <&apss_shared 4>;
			fastrpc {
				compatible = "qcom,fastrpc";
				qcom,glink-channels = "fastrpcglink-apps-dsp";
				label = "cdsp";
				qcom,non-secure-domain;
				#address-cells = <1>;
				#size-cells = <0>;

				compute-cb@1 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <1>;
					iommus = <&apps_smmu 0x1401 0x30>;
				};

				compute-cb@2 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <2>;
					iommus = <&apps_smmu 0x1402 0x30>;
				};

				compute-cb@3 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <3>;
					iommus = <&apps_smmu 0x1403 0x30>;
				};

				compute-cb@4 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <4>;
					iommus = <&apps_smmu 0x1404 0x30>;
				};

				compute-cb@5 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <5>;
					iommus = <&apps_smmu 0x1405 0x30>;
				};

				compute-cb@6 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <6>;
					iommus = <&apps_smmu 0x1406 0x30>;
				};

				compute-cb@7 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <7>;
					iommus = <&apps_smmu 0x1407 0x30>;
				};

				compute-cb@8 {
					compatible = "qcom,fastrpc-compute-cb";
					reg = <8>;
					iommus = <&apps_smmu 0x1408 0x30>;
				};
			};
		};
	};

	smp2p-cdsp {
		compatible = "qcom,smp2p";
		qcom,smem = <94>, <432>;

		interrupts = <GIC_SPI 576 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apss_shared 6>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <5>;

		cdsp_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		cdsp_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-lpass {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;

		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apss_shared 10>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		adsp_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		adsp_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-mpss {
		compatible = "qcom,smp2p";
		qcom,smem = <435>, <428>;
		interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>;
		mboxes = <&apss_shared 14>;
		qcom,local-pid = <0>;
		qcom,remote-pid = <1>;

		modem_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		modem_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		ipa_smp2p_out: ipa-ap-to-modem {
			qcom,entry-name = "ipa";
			#qcom,smem-state-cells = <1>;
		};

		ipa_smp2p_in: ipa-modem-to-ap {
			qcom,entry-name = "ipa";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-slpi {
		compatible = "qcom,smp2p";
		qcom,smem = <481>, <430>;
		interrupts = <GIC_SPI 172 IRQ_TYPE_EDGE_RISING>;
		mboxes = <&apss_shared 26>;
		qcom,local-pid = <0>;
		qcom,remote-pid = <3>;

		slpi_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		slpi_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges = <0 0 0 0 0x10 0>;
		dma-ranges = <0 0 0 0 0x10 0>;
		compatible = "simple-bus";

		gcc: clock-controller@100000 {
			compatible = "qcom,gcc-sdm845";
			reg = <0 0x00100000 0 0x1f0000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&rpmhcc RPMH_CXO_CLK_A>,
				 <&sleep_clk>,
				 <&pcie0_phy>,
				 <&pcie1_phy>;
			clock-names = "bi_tcxo",
				      "bi_tcxo_ao",
				      "sleep_clk",
				      "pcie_0_pipe_clk",
				      "pcie_1_pipe_clk";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			power-domains = <&rpmhpd SDM845_CX>;
		};

		qfprom@784000 {
			compatible = "qcom,sdm845-qfprom", "qcom,qfprom";
			reg = <0 0x00784000 0 0x8ff>;
			#address-cells = <1>;
			#size-cells = <1>;

			qusb2p_hstx_trim: hstx-trim-primary@1eb {
				reg = <0x1eb 0x1>;
				bits = <1 4>;
			};

			qusb2s_hstx_trim: hstx-trim-secondary@1eb {
				reg = <0x1eb 0x2>;
				bits = <6 4>;
			};
		};

		rng: rng@793000 {
			compatible = "qcom,prng-ee";
			reg = <0 0x00793000 0 0x1000>;
			clocks = <&gcc GCC_PRNG_AHB_CLK>;
			clock-names = "core";
		};

		gpi_dma0: dma-controller@800000 {
			#dma-cells = <3>;
			compatible = "qcom,sdm845-gpi-dma";
			reg = <0 0x00800000 0 0x60000>;
			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <13>;
			dma-channel-mask = <0xfa>;
			iommus = <&apps_smmu 0x0016 0x0>;
			status = "disabled";
		};

		qupv3_id_0: geniqup@8c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x008c0000 0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
			iommus = <&apps_smmu 0x3 0x0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>;
			interconnect-names = "qup-core";
			status = "disabled";

			i2c0: i2c@880000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c0_default>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi0: spi@880000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi0_default>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart0: serial@880000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart0_default>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c1: i2c@884000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c1_default>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi1: spi@884000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi1_default>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart1: serial@884000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart1_default>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c2: i2c@888000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c2_default>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi2: spi@888000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi2_default>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart2: serial@888000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart2_default>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c3: i2c@88c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c3_default>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi3: spi@88c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi3_default>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart3: serial@88c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart3_default>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c4: i2c@890000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c4_default>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi4: spi@890000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi4_default>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart4: serial@890000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart4_default>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c5: i2c@894000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c5_default>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi5: spi@894000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi5_default>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart5: serial@894000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart5_default>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c6: i2c@898000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00898000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c6_default>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi6: spi@898000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00898000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi6_default>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart6: serial@898000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00898000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart6_default>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c7: i2c@89c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0089c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c7_default>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				status = "disabled";
			};

			spi7: spi@89c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0089c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi7_default>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 7 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart7: serial@89c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x0089c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart7_default>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};
		};

		gpi_dma1: dma-controller@a00000 {
			#dma-cells = <3>;
			compatible = "qcom,sdm845-gpi-dma";
			reg = <0 0x00a00000 0 0x60000>;
			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <13>;
			dma-channel-mask = <0xfa>;
			iommus = <&apps_smmu 0x06d6 0x0>;
			status = "disabled";
		};

		qupv3_id_1: geniqup@ac0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x00ac0000 0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
			iommus = <&apps_smmu 0x6c3 0x0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>;
			interconnect-names = "qup-core";
			status = "disabled";

			i2c8: i2c@a80000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c8_default>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi8: spi@a80000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi8_default>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart8: serial@a80000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart8_default>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c9: i2c@a84000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c9_default>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi9: spi@a84000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi9_default>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart9: serial@a84000 {
				compatible = "qcom,geni-debug-uart";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart9_default>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c10: i2c@a88000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c10_default>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi10: spi@a88000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi10_default>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart10: serial@a88000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart10_default>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c11: i2c@a8c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c11_default>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi11: spi@a8c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi11_default>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart11: serial@a8c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart11_default>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c12: i2c@a90000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c12_default>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi12: spi@a90000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi12_default>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart12: serial@a90000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart12_default>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c13: i2c@a94000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c13_default>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi13: spi@a94000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi13_default>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart13: serial@a94000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart13_default>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c14: i2c@a98000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a98000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c14_default>;
				interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			spi14: spi@a98000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a98000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi14_default>;
				interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 6 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart14: serial@a98000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a98000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart14_default>;
				interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c15: i2c@a9c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a9c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c15_default>;
				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				status = "disabled";
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 7 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
			};

			spi15: spi@a9c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a9c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_spi15_default>;
				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 7 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				status = "disabled";
			};

			uart15: serial@a9c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a9c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart15_default>;
				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SDM845_CX>;
				operating-points-v2 = <&qup_opp_table>;
				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};
		};

		llcc: system-cache-controller@1100000 {
			compatible = "qcom,sdm845-llcc";
			reg = <0 0x01100000 0 0x45000>, <0 0x01180000 0 0x50000>,
			      <0 0x01200000 0 0x50000>, <0 0x01280000 0 0x50000>,
			      <0 0x01300000 0 0x50000>;
			reg-names = "llcc0_base", "llcc1_base", "llcc2_base",
				    "llcc3_base", "llcc_broadcast_base";
			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
		};

		dma@10a2000 {
			compatible = "qcom,sdm845-dcc", "qcom,dcc";
			reg = <0x0 0x010a2000 0x0 0x1000>,
			      <0x0 0x010ae000 0x0 0x2000>;
		};

		pmu@114a000 {
			compatible = "qcom,sdm845-llcc-bwmon";
			reg = <0 0x0114a000 0 0x1000>;
			interrupts = <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
			interconnects = <&mem_noc MASTER_LLCC 3 &mem_noc SLAVE_EBI1 3>;

			operating-points-v2 = <&llcc_bwmon_opp_table>;

			llcc_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				/*
				 * The interconnect path bandwidth taken from
				 * cpu4_opp_table bandwidth for gladiator_noc-mem_noc
				 * interconnect.  This also matches the
				 * bandwidth table of qcom,llccbw (qcom,bw-tbl,
				 * bus width: 4 bytes) from msm-4.9 downstream
				 * kernel.
				 */
				opp-0 {
					opp-peak-kBps = <800000>;
				};
				opp-1 {
					opp-peak-kBps = <1804000>;
				};
				opp-2 {
					opp-peak-kBps = <3072000>;
				};
				opp-3 {
					opp-peak-kBps = <5412000>;
				};
				opp-4 {
					opp-peak-kBps = <7216000>;
				};
			};
		};

		pmu@1436400 {
			compatible = "qcom,sdm845-cpu-bwmon", "qcom,sdm845-bwmon";
			reg = <0 0x01436400 0 0x600>;
			interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_LLCC 3>;

			operating-points-v2 = <&cpu_bwmon_opp_table>;

			cpu_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				/*
				 * The interconnect path bandwidth taken from
				 * cpu4_opp_table bandwidth for OSM L3
				 * interconnect.  This also matches the OSM L3
				 * from bandwidth table of qcom,cpu4-l3lat-mon
				 * (qcom,core-dev-table, bus width: 16 bytes)
				 * from msm-4.9 downstream kernel.
				 */
				opp-0 {
					opp-peak-kBps = <4800000>;
				};
				opp-1 {
					opp-peak-kBps = <9216000>;
				};
				opp-2 {
					opp-peak-kBps = <15052800>;
				};
				opp-3 {
					opp-peak-kBps = <20889600>;
				};
				opp-4 {
					opp-peak-kBps = <25497600>;
				};
			};
		};

		pcie0: pcie@1c00000 {
			compatible = "qcom,pcie-sdm845";
			reg = <0 0x01c00000 0 0x2000>,
			      <0 0x60000000 0 0xf1d>,
			      <0 0x60000f20 0 0xa8>,
			      <0 0x60100000 0 0x100000>,
			      <0 0x01c07000 0 0x1000>;
			reg-names = "parf", "dbi", "elbi", "config", "mhi";
			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0xd00000>;

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
				 <&gcc GCC_PCIE_0_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "tbu";

			iommu-map = <0x0   &apps_smmu 0x1c10 0x1>,
				    <0x100 &apps_smmu 0x1c11 0x1>,
				    <0x200 &apps_smmu 0x1c12 0x1>,
				    <0x300 &apps_smmu 0x1c13 0x1>,
				    <0x400 &apps_smmu 0x1c14 0x1>,
				    <0x500 &apps_smmu 0x1c15 0x1>,
				    <0x600 &apps_smmu 0x1c16 0x1>,
				    <0x700 &apps_smmu 0x1c17 0x1>,
				    <0x800 &apps_smmu 0x1c18 0x1>,
				    <0x900 &apps_smmu 0x1c19 0x1>,
				    <0xa00 &apps_smmu 0x1c1a 0x1>,
				    <0xb00 &apps_smmu 0x1c1b 0x1>,
				    <0xc00 &apps_smmu 0x1c1c 0x1>,
				    <0xd00 &apps_smmu 0x1c1d 0x1>,
				    <0xe00 &apps_smmu 0x1c1e 0x1>,
				    <0xf00 &apps_smmu 0x1c1f 0x1>;

			resets = <&gcc GCC_PCIE_0_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_0_GDSC>;

			phys = <&pcie0_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie0_phy: phy@1c06000 {
			compatible = "qcom,sdm845-qmp-pcie-phy";
			reg = <0 0x01c06000 0 0x1000>;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
				 <&gcc GCC_PCIE_PHY_REFGEN_CLK>,
				 <&gcc GCC_PCIE_0_PIPE_CLK>;
			clock-names = "aux",
				      "cfg_ahb",
				      "ref",
				      "refgen",
				      "pipe";

			clock-output-names = "pcie_0_pipe_clk";
			#clock-cells = <0>;

			#phy-cells = <0>;

			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";
		};

		pcie1: pcie@1c08000 {
			compatible = "qcom,pcie-sdm845";
			reg = <0 0x01c08000 0 0x2000>,
			      <0 0x40000000 0 0xf1d>,
			      <0 0x40000f20 0 0xa8>,
			      <0 0x40100000 0 0x100000>,
			      <0 0x01c0c000 0 0x1000>;
			reg-names = "parf", "dbi", "elbi", "config", "mhi";
			device_type = "pci";
			linux,pci-domain = <1>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;

			interrupts = <GIC_SPI 307 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
				 <&gcc GCC_PCIE_1_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ref",
				      "tbu";

			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
				    <0x100 &apps_smmu 0x1c01 0x1>,
				    <0x200 &apps_smmu 0x1c02 0x1>,
				    <0x300 &apps_smmu 0x1c03 0x1>,
				    <0x400 &apps_smmu 0x1c04 0x1>,
				    <0x500 &apps_smmu 0x1c05 0x1>,
				    <0x600 &apps_smmu 0x1c06 0x1>,
				    <0x700 &apps_smmu 0x1c07 0x1>,
				    <0x800 &apps_smmu 0x1c08 0x1>,
				    <0x900 &apps_smmu 0x1c09 0x1>,
				    <0xa00 &apps_smmu 0x1c0a 0x1>,
				    <0xb00 &apps_smmu 0x1c0b 0x1>,
				    <0xc00 &apps_smmu 0x1c0c 0x1>,
				    <0xd00 &apps_smmu 0x1c0d 0x1>,
				    <0xe00 &apps_smmu 0x1c0e 0x1>,
				    <0xf00 &apps_smmu 0x1c0f 0x1>;

			resets = <&gcc GCC_PCIE_1_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_1_GDSC>;

			phys = <&pcie1_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie1_phy: phy@1c0a000 {
			compatible = "qcom,sdm845-qhp-pcie-phy";
			reg = <0 0x01c0a000 0 0x2000>;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
				 <&gcc GCC_PCIE_PHY_REFGEN_CLK>,
				 <&gcc GCC_PCIE_1_PIPE_CLK>;
			clock-names = "aux",
				      "cfg_ahb",
				      "ref",
				      "refgen",
				      "pipe";

			clock-output-names = "pcie_1_pipe_clk";
			#clock-cells = <0>;

			#phy-cells = <0>;

			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";
		};

		mem_noc: interconnect@1380000 {
			compatible = "qcom,sdm845-mem-noc";
			reg = <0 0x01380000 0 0x27200>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		dc_noc: interconnect@14e0000 {
			compatible = "qcom,sdm845-dc-noc";
			reg = <0 0x014e0000 0 0x400>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		config_noc: interconnect@1500000 {
			compatible = "qcom,sdm845-config-noc";
			reg = <0 0x01500000 0 0x5080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		system_noc: interconnect@1620000 {
			compatible = "qcom,sdm845-system-noc";
			reg = <0 0x01620000 0 0x18080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre1_noc: interconnect@16e0000 {
			compatible = "qcom,sdm845-aggre1-noc";
			reg = <0 0x016e0000 0 0x15080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre2_noc: interconnect@1700000 {
			compatible = "qcom,sdm845-aggre2-noc";
			reg = <0 0x01700000 0 0x1f300>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mmss_noc: interconnect@1740000 {
			compatible = "qcom,sdm845-mmss-noc";
			reg = <0 0x01740000 0 0x1c100>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		ufs_mem_hc: ufshc@1d84000 {
			compatible = "qcom,sdm845-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01d84000 0 0x2500>,
			      <0 0x01d90000 0 0x8000>;
			reg-names = "std", "ice";
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_mem_phy>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			power-domains = <&gcc UFS_PHY_GDSC>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_PHY_BCR>;
			reset-names = "rst";

			iommus = <&apps_smmu 0x100 0xf>;

			clock-names =
				"core_clk",
				"bus_aggr_clk",
				"iface_clk",
				"core_clk_unipro",
				"ref_clk",
				"tx_lane0_sync_clk",
				"rx_lane0_sync_clk",
				"rx_lane1_sync_clk",
				"ice_core_clk";
			clocks =
				<&gcc GCC_UFS_PHY_AXI_CLK>,
				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				<&gcc GCC_UFS_PHY_AHB_CLK>,
				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
				<&rpmhcc RPMH_CXO_CLK>,
				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>,
				<&gcc GCC_UFS_PHY_ICE_CORE_CLK>;

			operating-points-v2 = <&ufs_opp_table>;

			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mem_noc SLAVE_EBI1 0>,
					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
			interconnect-names = "ufs-ddr", "cpu-ufs";

			status = "disabled";

			ufs_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-50000000 {
					opp-hz = /bits/ 64 <50000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <37500000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <75000000>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <150000000>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <0>,
						 /bits/ 64 <300000000>;
					required-opps = <&rpmhpd_opp_nom>;
				};
			};
		};

		ufs_mem_phy: phy@1d87000 {
			compatible = "qcom,sdm845-qmp-ufs-phy";
			reg = <0 0x01d87000 0 0x1000>;

			clock-names = "ref",
				      "ref_aux";
			clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;

			resets = <&ufs_mem_hc 0>;
			reset-names = "ufsphy";

			#phy-cells = <0>;
			status = "disabled";
		};

		cryptobam: dma-controller@1dc4000 {
			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
			reg = <0 0x01dc4000 0 0x24000>;
			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&rpmhcc RPMH_CE_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
			qcom,controlled-remotely;
			iommus = <&apps_smmu 0x704 0x1>,
				 <&apps_smmu 0x706 0x1>,
				 <&apps_smmu 0x714 0x1>,
				 <&apps_smmu 0x716 0x1>;
		};

		crypto: crypto@1dfa000 {
			compatible = "qcom,crypto-v5.4";
			reg = <0 0x01dfa000 0 0x6000>;
			clocks = <&gcc GCC_CE1_AHB_CLK>,
				 <&gcc GCC_CE1_AXI_CLK>,
				 <&rpmhcc RPMH_CE_CLK>;
			clock-names = "iface", "bus", "core";
			dmas = <&cryptobam 6>, <&cryptobam 7>;
			dma-names = "rx", "tx";
			iommus = <&apps_smmu 0x704 0x1>,
				 <&apps_smmu 0x706 0x1>,
				 <&apps_smmu 0x714 0x1>,
				 <&apps_smmu 0x716 0x1>;
		};

		ipa: ipa@1e40000 {
			compatible = "qcom,sdm845-ipa";

			iommus = <&apps_smmu 0x720 0x0>,
				 <&apps_smmu 0x722 0x0>;
			reg = <0 0x01e40000 0 0x7000>,
			      <0 0x01e47000 0 0x2000>,
			      <0 0x01e04000 0 0x2c000>;
			reg-names = "ipa-reg",
				    "ipa-shared",
				    "gsi";

			interrupts-extended = <&intc GIC_SPI 311 IRQ_TYPE_EDGE_RISING>,
					      <&intc GIC_SPI 432 IRQ_TYPE_LEVEL_HIGH>,
					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "ipa",
					  "gsi",
					  "ipa-clock-query",
					  "ipa-setup-ready";

			clocks = <&rpmhcc RPMH_IPA_CLK>;
			clock-names = "core";

			interconnects = <&aggre2_noc MASTER_IPA 0 &mem_noc SLAVE_EBI1 0>,
					<&aggre2_noc MASTER_IPA 0 &system_noc SLAVE_IMEM 0>,
					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_IPA_CFG 0>;
			interconnect-names = "memory",
					     "imem",
					     "config";

			qcom,smem-states = <&ipa_smp2p_out 0>,
					   <&ipa_smp2p_out 1>;
			qcom,smem-state-names = "ipa-clock-enabled-valid",
						"ipa-clock-enabled";

			status = "disabled";
		};

		tcsr_mutex: hwlock@1f40000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0 0x01f40000 0 0x20000>;
			#hwlock-cells = <1>;
		};

		tcsr_regs_1: syscon@1f60000 {
			compatible = "qcom,sdm845-tcsr", "syscon";
			reg = <0 0x01f60000 0 0x20000>;
		};

		tlmm: pinctrl@3400000 {
			compatible = "qcom,sdm845-pinctrl";
			reg = <0 0x03400000 0 0xc00000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			gpio-ranges = <&tlmm 0 0 151>;
			wakeup-parent = <&pdc_intc>;

			cci0_default: cci0-default-state {
				/* SDA, SCL */
				pins = "gpio17", "gpio18";
				function = "cci_i2c";

				bias-pull-up;
				drive-strength = <2>; /* 2 mA */
			};

			cci0_sleep: cci0-sleep-state {
				/* SDA, SCL */
				pins = "gpio17", "gpio18";
				function = "cci_i2c";

				drive-strength = <2>; /* 2 mA */
				bias-pull-down;
			};

			cci1_default: cci1-default-state {
				/* SDA, SCL */
				pins = "gpio19", "gpio20";
				function = "cci_i2c";

				bias-pull-up;
				drive-strength = <2>; /* 2 mA */
			};

			cci1_sleep: cci1-sleep-state {
				/* SDA, SCL */
				pins = "gpio19", "gpio20";
				function = "cci_i2c";

				drive-strength = <2>; /* 2 mA */
				bias-pull-down;
			};

			qspi_clk: qspi-clk-state {
				pins = "gpio95";
				function = "qspi_clk";
			};

			qspi_cs0: qspi-cs0-state {
				pins = "gpio90";
				function = "qspi_cs";
			};

			qspi_cs1: qspi-cs1-state {
				pins = "gpio89";
				function = "qspi_cs";
			};

			qspi_data0: qspi-data0-state {
				pins = "gpio91";
				function = "qspi_data";
			};

			qspi_data1: qspi-data1-state {
				pins = "gpio92";
				function = "qspi_data";
			};

			qspi_data23: qspi-data23-state {
				pins = "gpio93", "gpio94";
				function = "qspi_data";
			};

			qup_i2c0_default: qup-i2c0-default-state {
				pins = "gpio0", "gpio1";
				function = "qup0";
			};

			qup_i2c1_default: qup-i2c1-default-state {
				pins = "gpio17", "gpio18";
				function = "qup1";
			};

			qup_i2c2_default: qup-i2c2-default-state {
				pins = "gpio27", "gpio28";
				function = "qup2";
			};

			qup_i2c3_default: qup-i2c3-default-state {
				pins = "gpio41", "gpio42";
				function = "qup3";
			};

			qup_i2c4_default: qup-i2c4-default-state {
				pins = "gpio89", "gpio90";
				function = "qup4";
			};

			qup_i2c5_default: qup-i2c5-default-state {
				pins = "gpio85", "gpio86";
				function = "qup5";
			};

			qup_i2c6_default: qup-i2c6-default-state {
				pins = "gpio45", "gpio46";
				function = "qup6";
			};

			qup_i2c7_default: qup-i2c7-default-state {
				pins = "gpio93", "gpio94";
				function = "qup7";
			};

			qup_i2c8_default: qup-i2c8-default-state {
				pins = "gpio65", "gpio66";
				function = "qup8";
			};

			qup_i2c9_default: qup-i2c9-default-state {
				pins = "gpio6", "gpio7";
				function = "qup9";
			};

			qup_i2c10_default: qup-i2c10-default-state {
				pins = "gpio55", "gpio56";
				function = "qup10";
			};

			qup_i2c11_default: qup-i2c11-default-state {
				pins = "gpio31", "gpio32";
				function = "qup11";
			};

			qup_i2c12_default: qup-i2c12-default-state {
				pins = "gpio49", "gpio50";
				function = "qup12";
			};

			qup_i2c13_default: qup-i2c13-default-state {
				pins = "gpio105", "gpio106";
				function = "qup13";
			};

			qup_i2c14_default: qup-i2c14-default-state {
				pins = "gpio33", "gpio34";
				function = "qup14";
			};

			qup_i2c15_default: qup-i2c15-default-state {
				pins = "gpio81", "gpio82";
				function = "qup15";
			};

			qup_spi0_default: qup-spi0-default-state {
				pins = "gpio0", "gpio1", "gpio2", "gpio3";
				function = "qup0";
			};

			qup_spi1_default: qup-spi1-default-state {
				pins = "gpio17", "gpio18", "gpio19", "gpio20";
				function = "qup1";
			};

			qup_spi2_default: qup-spi2-default-state {
				pins = "gpio27", "gpio28", "gpio29", "gpio30";
				function = "qup2";
			};

			qup_spi3_default: qup-spi3-default-state {
				pins = "gpio41", "gpio42", "gpio43", "gpio44";
				function = "qup3";
			};

			qup_spi4_default: qup-spi4-default-state {
				pins = "gpio89", "gpio90", "gpio91", "gpio92";
				function = "qup4";
			};

			qup_spi5_default: qup-spi5-default-state {
				pins = "gpio85", "gpio86", "gpio87", "gpio88";
				function = "qup5";
			};

			qup_spi6_default: qup-spi6-default-state {
				pins = "gpio45", "gpio46", "gpio47", "gpio48";
				function = "qup6";
			};

			qup_spi7_default: qup-spi7-default-state {
				pins = "gpio93", "gpio94", "gpio95", "gpio96";
				function = "qup7";
			};

			qup_spi8_default: qup-spi8-default-state {
				pins = "gpio65", "gpio66", "gpio67", "gpio68";
				function = "qup8";
			};

			qup_spi9_default: qup-spi9-default-state {
				pins = "gpio6", "gpio7", "gpio4", "gpio5";
				function = "qup9";
			};

			qup_spi10_default: qup-spi10-default-state {
				pins = "gpio55", "gpio56", "gpio53", "gpio54";
				function = "qup10";
			};

			qup_spi11_default: qup-spi11-default-state {
				pins = "gpio31", "gpio32", "gpio33", "gpio34";
				function = "qup11";
			};

			qup_spi12_default: qup-spi12-default-state {
				pins = "gpio49", "gpio50", "gpio51", "gpio52";
				function = "qup12";
			};

			qup_spi13_default: qup-spi13-default-state {
				pins = "gpio105", "gpio106", "gpio107", "gpio108";
				function = "qup13";
			};

			qup_spi14_default: qup-spi14-default-state {
				pins = "gpio33", "gpio34", "gpio31", "gpio32";
				function = "qup14";
			};

			qup_spi15_default: qup-spi15-default-state {
				pins = "gpio81", "gpio82", "gpio83", "gpio84";
				function = "qup15";
			};

			qup_uart0_default: qup-uart0-default-state {
				qup_uart0_tx: tx-pins {
					pins = "gpio2";
					function = "qup0";
				};

				qup_uart0_rx: rx-pins {
					pins = "gpio3";
					function = "qup0";
				};
			};

			qup_uart1_default: qup-uart1-default-state {
				qup_uart1_tx: tx-pins {
					pins = "gpio19";
					function = "qup1";
				};

				qup_uart1_rx: rx-pins {
					pins = "gpio20";
					function = "qup1";
				};
			};

			qup_uart2_default: qup-uart2-default-state {
				qup_uart2_tx: tx-pins {
					pins = "gpio29";
					function = "qup2";
				};

				qup_uart2_rx: rx-pins {
					pins = "gpio30";
					function = "qup2";
				};
			};

			qup_uart3_default: qup-uart3-default-state {
				qup_uart3_tx: tx-pins {
					pins = "gpio43";
					function = "qup3";
				};

				qup_uart3_rx: rx-pins {
					pins = "gpio44";
					function = "qup3";
				};
			};

			qup_uart3_4pin: qup-uart3-4pin-state {
				qup_uart3_4pin_cts: cts-pins {
					pins = "gpio41";
					function = "qup3";
				};

				qup_uart3_4pin_rts_tx: rts-tx-pins {
					pins = "gpio42", "gpio43";
					function = "qup3";
				};

				qup_uart3_4pin_rx: rx-pins {
					pins = "gpio44";
					function = "qup3";
				};
			};

			qup_uart4_default: qup-uart4-default-state {
				qup_uart4_tx: tx-pins {
					pins = "gpio91";
					function = "qup4";
				};

				qup_uart4_rx: rx-pins {
					pins = "gpio92";
					function = "qup4";
				};
			};

			qup_uart5_default: qup-uart5-default-state {
				qup_uart5_tx: tx-pins {
					pins = "gpio87";
					function = "qup5";
				};

				qup_uart5_rx: rx-pins {
					pins = "gpio88";
					function = "qup5";
				};
			};

			qup_uart6_default: qup-uart6-default-state {
				qup_uart6_tx: tx-pins {
					pins = "gpio47";
					function = "qup6";
				};

				qup_uart6_rx: rx-pins {
					pins = "gpio48";
					function = "qup6";
				};
			};

			qup_uart6_4pin: qup-uart6-4pin-state {
				qup_uart6_4pin_cts: cts-pins {
					pins = "gpio45";
					function = "qup6";
					bias-pull-down;
				};

				qup_uart6_4pin_rts_tx: rts-tx-pins {
					pins = "gpio46", "gpio47";
					function = "qup6";
					drive-strength = <2>;
					bias-disable;
				};

				qup_uart6_4pin_rx: rx-pins {
					pins = "gpio48";
					function = "qup6";
					bias-pull-up;
				};
			};

			qup_uart7_default: qup-uart7-default-state {
				qup_uart7_tx: tx-pins {
					pins = "gpio95";
					function = "qup7";
				};

				qup_uart7_rx: rx-pins {
					pins = "gpio96";
					function = "qup7";
				};
			};

			qup_uart8_default: qup-uart8-default-state {
				qup_uart8_tx: tx-pins {
					pins = "gpio67";
					function = "qup8";
				};

				qup_uart8_rx: rx-pins {
					pins = "gpio68";
					function = "qup8";
				};
			};

			qup_uart9_default: qup-uart9-default-state {
				qup_uart9_tx: tx-pins {
					pins = "gpio4";
					function = "qup9";
				};

				qup_uart9_rx: rx-pins {
					pins = "gpio5";
					function = "qup9";
				};
			};

			qup_uart10_default: qup-uart10-default-state {
				qup_uart10_tx: tx-pins {
					pins = "gpio53";
					function = "qup10";
				};

				qup_uart10_rx: rx-pins {
					pins = "gpio54";
					function = "qup10";
				};
			};

			qup_uart11_default: qup-uart11-default-state {
				qup_uart11_tx: tx-pins {
					pins = "gpio33";
					function = "qup11";
				};

				qup_uart11_rx: rx-pins {
					pins = "gpio34";
					function = "qup11";
				};
			};

			qup_uart12_default: qup-uart12-default-state {
				qup_uart12_tx: tx-pins {
					pins = "gpio51";
					function = "qup0";
				};

				qup_uart12_rx: rx-pins {
					pins = "gpio52";
					function = "qup0";
				};
			};

			qup_uart13_default: qup-uart13-default-state {
				qup_uart13_tx: tx-pins {
					pins = "gpio107";
					function = "qup13";
				};

				qup_uart13_rx: rx-pins {
					pins = "gpio108";
					function = "qup13";
				};
			};

			qup_uart14_default: qup-uart14-default-state {
				qup_uart14_tx: tx-pins {
					pins = "gpio31";
					function = "qup14";
				};

				qup_uart14_rx: rx-pins {
					pins = "gpio32";
					function = "qup14";
				};
			};

			qup_uart15_default: qup-uart15-default-state {
				qup_uart15_tx: tx-pins {
					pins = "gpio83";
					function = "qup15";
				};

				qup_uart15_rx: rx-pins {
					pins = "gpio84";
					function = "qup15";
				};
			};

			quat_mi2s_sleep: quat-mi2s-sleep-state {
				pins = "gpio58", "gpio59";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			quat_mi2s_active: quat-mi2s-active-state {
				pins = "gpio58", "gpio59";
				function = "qua_mi2s";
				drive-strength = <8>;
				bias-disable;
				output-high;
			};

			quat_mi2s_sd0_sleep: quat-mi2s-sd0-sleep-state {
				pins = "gpio60";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			quat_mi2s_sd0_active: quat-mi2s-sd0-active-state {
				pins = "gpio60";
				function = "qua_mi2s";
				drive-strength = <8>;
				bias-disable;
			};

			quat_mi2s_sd1_sleep: quat-mi2s-sd1-sleep-state {
				pins = "gpio61";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			quat_mi2s_sd1_active: quat-mi2s-sd1-active-state {
				pins = "gpio61";
				function = "qua_mi2s";
				drive-strength = <8>;
				bias-disable;
			};

			quat_mi2s_sd2_sleep: quat-mi2s-sd2-sleep-state {
				pins = "gpio62";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			quat_mi2s_sd2_active: quat-mi2s-sd2-active-state {
				pins = "gpio62";
				function = "qua_mi2s";
				drive-strength = <8>;
				bias-disable;
			};

			quat_mi2s_sd3_sleep: quat-mi2s-sd3-sleep-state {
				pins = "gpio63";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			quat_mi2s_sd3_active: quat-mi2s-sd3-active-state {
				pins = "gpio63";
				function = "qua_mi2s";
				drive-strength = <8>;
				bias-disable;
			};
		};

		mss_pil: remoteproc@4080000 {
			compatible = "qcom,sdm845-mss-pil";
			reg = <0 0x04080000 0 0x408>, <0 0x04180000 0 0x48>;
			reg-names = "qdsp6", "rmb";

			interrupts-extended =
				<&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>,
				<&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
				<&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
				<&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
				<&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
				<&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack",
					  "shutdown-ack";

			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
				 <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
				 <&gcc GCC_MSS_GPLL0_DIV_CLK_SRC>,
				 <&gcc GCC_MSS_SNOC_AXI_CLK>,
				 <&gcc GCC_MSS_MFAB_AXIS_CLK>,
				 <&gcc GCC_PRNG_AHB_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "iface", "bus", "mem", "gpll0_mss",
				      "snoc_axi", "mnoc_axi", "prng", "xo";

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&modem_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
				 <&pdc_reset PDC_MODEM_SYNC_RESET>;
			reset-names = "mss_restart", "pdc_reset";

			qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;

			power-domains = <&rpmhpd SDM845_CX>,
					<&rpmhpd SDM845_MX>,
					<&rpmhpd SDM845_MSS>;
			power-domain-names = "cx", "mx", "mss";

			status = "disabled";

			mba {
				memory-region = <&mba_region>;
			};

			mpss {
				memory-region = <&mpss_region>;
			};

			metadata {
				memory-region = <&mdata_mem>;
			};

			glink-edge {
				interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
				label = "modem";
				qcom,remote-pid = <1>;
				mboxes = <&apss_shared 12>;
			};
		};

		gpucc: clock-controller@5090000 {
			compatible = "qcom,sdm845-gpucc";
			reg = <0 0x05090000 0 0x9000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
			clock-names = "bi_tcxo",
				      "gcc_gpu_gpll0_clk_src",
				      "gcc_gpu_gpll0_div_clk_src";
		};

		slpi_pas: remoteproc@5c00000 {
			compatible = "qcom,sdm845-slpi-pas";
			reg = <0 0x5c00000 0 0x4000>;

			interrupts-extended = <&intc GIC_SPI 494 IRQ_TYPE_EDGE_RISING>,
						<&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
						<&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
						<&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
						<&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
						"handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			qcom,qmp = <&aoss_qmp>;

			power-domains = <&rpmhpd SDM845_CX>,
					<&rpmhpd SDM845_MX>;
			power-domain-names = "lcx", "lmx";

			memory-region = <&slpi_mem>;

			qcom,smem-states = <&slpi_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts = <GIC_SPI 170 IRQ_TYPE_EDGE_RISING>;
				label = "dsps";
				qcom,remote-pid = <3>;
				mboxes = <&apss_shared 24>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "sdsp";
					qcom,non-secure-domain;
					qcom,vmids = <QCOM_SCM_VMID_HLOS QCOM_SCM_VMID_MSS_MSA
						      QCOM_SCM_VMID_SSC_Q6 QCOM_SCM_VMID_ADSP_Q6>;
					memory-region = <&fastrpc_mem>;
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@0 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <0>;
					};
				};
			};
		};

		stm@6002000 {
			compatible = "arm,coresight-stm", "arm,primecell";
			reg = <0 0x06002000 0 0x1000>,
			      <0 0x16280000 0 0x180000>;
			reg-names = "stm-base", "stm-stimulus-base";

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					stm_out: endpoint {
						remote-endpoint =
						  <&funnel0_in7>;
					};
				};
			};
		};

		funnel@6041000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0 0x06041000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					funnel0_out: endpoint {
						remote-endpoint =
						  <&merge_funnel_in0>;
					};
				};
			};

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@7 {
					reg = <7>;
					funnel0_in7: endpoint {
						remote-endpoint = <&stm_out>;
					};
				};
			};
		};

		funnel@6043000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0 0x06043000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					funnel2_out: endpoint {
						remote-endpoint =
						  <&merge_funnel_in2>;
					};
				};
			};

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@5 {
					reg = <5>;
					funnel2_in5: endpoint {
						remote-endpoint =
						  <&apss_merge_funnel_out>;
					};
				};
			};
		};

		funnel@6045000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0 0x06045000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					merge_funnel_out: endpoint {
						remote-endpoint = <&etf_in>;
					};
				};
			};

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					merge_funnel_in0: endpoint {
						remote-endpoint =
						  <&funnel0_out>;
					};
				};

				port@2 {
					reg = <2>;
					merge_funnel_in2: endpoint {
						remote-endpoint =
						  <&funnel2_out>;
					};
				};
			};
		};

		replicator@6046000 {
			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
			reg = <0 0x06046000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					replicator_out: endpoint {
						remote-endpoint = <&etr_in>;
					};
				};
			};

			in-ports {
				port {
					replicator_in: endpoint {
						remote-endpoint = <&etf_out>;
					};
				};
			};
		};

		etf@6047000 {
			compatible = "arm,coresight-tmc", "arm,primecell";
			reg = <0 0x06047000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					etf_out: endpoint {
						remote-endpoint =
						  <&replicator_in>;
					};
				};
			};

			in-ports {

				port {
					etf_in: endpoint {
						remote-endpoint =
						  <&merge_funnel_out>;
					};
				};
			};
		};

		etr@6048000 {
			compatible = "arm,coresight-tmc", "arm,primecell";
			reg = <0 0x06048000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,scatter-gather;

			in-ports {
				port {
					etr_in: endpoint {
						remote-endpoint =
						  <&replicator_out>;
					};
				};
			};
		};

		etm@7040000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07040000 0 0x1000>;

			cpu = <&CPU0>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm0_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in0>;
					};
				};
			};
		};

		etm@7140000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07140000 0 0x1000>;

			cpu = <&CPU1>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm1_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in1>;
					};
				};
			};
		};

		etm@7240000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07240000 0 0x1000>;

			cpu = <&CPU2>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm2_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in2>;
					};
				};
			};
		};

		etm@7340000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07340000 0 0x1000>;

			cpu = <&CPU3>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm3_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in3>;
					};
				};
			};
		};

		etm@7440000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07440000 0 0x1000>;

			cpu = <&CPU4>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm4_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in4>;
					};
				};
			};
		};

		etm@7540000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07540000 0 0x1000>;

			cpu = <&CPU5>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm5_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in5>;
					};
				};
			};
		};

		etm@7640000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07640000 0 0x1000>;

			cpu = <&CPU6>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm6_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in6>;
					};
				};
			};
		};

		etm@7740000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0 0x07740000 0 0x1000>;

			cpu = <&CPU7>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";
			arm,coresight-loses-context-with-cpu;

			out-ports {
				port {
					etm7_out: endpoint {
						remote-endpoint =
						  <&apss_funnel_in7>;
					};
				};
			};
		};

		funnel@7800000 { /* APSS Funnel */
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0 0x07800000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					apss_funnel_out: endpoint {
						remote-endpoint =
						  <&apss_merge_funnel_in>;
					};
				};
			};

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					apss_funnel_in0: endpoint {
						remote-endpoint =
						  <&etm0_out>;
					};
				};

				port@1 {
					reg = <1>;
					apss_funnel_in1: endpoint {
						remote-endpoint =
						  <&etm1_out>;
					};
				};

				port@2 {
					reg = <2>;
					apss_funnel_in2: endpoint {
						remote-endpoint =
						  <&etm2_out>;
					};
				};

				port@3 {
					reg = <3>;
					apss_funnel_in3: endpoint {
						remote-endpoint =
						  <&etm3_out>;
					};
				};

				port@4 {
					reg = <4>;
					apss_funnel_in4: endpoint {
						remote-endpoint =
						  <&etm4_out>;
					};
				};

				port@5 {
					reg = <5>;
					apss_funnel_in5: endpoint {
						remote-endpoint =
						  <&etm5_out>;
					};
				};

				port@6 {
					reg = <6>;
					apss_funnel_in6: endpoint {
						remote-endpoint =
						  <&etm6_out>;
					};
				};

				port@7 {
					reg = <7>;
					apss_funnel_in7: endpoint {
						remote-endpoint =
						  <&etm7_out>;
					};
				};
			};
		};

		funnel@7810000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0 0x07810000 0 0x1000>;

			clocks = <&aoss_qmp>;
			clock-names = "apb_pclk";

			out-ports {
				port {
					apss_merge_funnel_out: endpoint {
						remote-endpoint =
						  <&funnel2_in5>;
					};
				};
			};

			in-ports {
				port {
					apss_merge_funnel_in: endpoint {
						remote-endpoint =
						  <&apss_funnel_out>;
					};
				};
			};
		};

		sdhc_2: mmc@8804000 {
			compatible = "qcom,sdm845-sdhci", "qcom,sdhci-msm-v5";
			reg = <0 0x08804000 0 0x1000>;

			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
				 <&gcc GCC_SDCC2_APPS_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "iface", "core", "xo";
			iommus = <&apps_smmu 0xa0 0xf>;
			power-domains = <&rpmhpd SDM845_CX>;
			operating-points-v2 = <&sdhc2_opp_table>;

			status = "disabled";

			sdhc2_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-9600000 {
					opp-hz = /bits/ 64 <9600000>;
					required-opps = <&rpmhpd_opp_min_svs>;
				};

				opp-19200000 {
					opp-hz = /bits/ 64 <19200000>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-100000000 {
					opp-hz = /bits/ 64 <100000000>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-201500000 {
					opp-hz = /bits/ 64 <201500000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
				};
			};
		};

		qspi: spi@88df000 {
			compatible = "qcom,sdm845-qspi", "qcom,qspi-v1";
			reg = <0 0x088df000 0 0x600>;
			iommus = <&apps_smmu 0x160 0x0>;
			#address-cells = <1>;
			#size-cells = <0>;
			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
				 <&gcc GCC_QSPI_CORE_CLK>;
			clock-names = "iface", "core";
			power-domains = <&rpmhpd SDM845_CX>;
			operating-points-v2 = <&qspi_opp_table>;
			status = "disabled";
		};

		slim: slim-ngd@171c0000 {
			compatible = "qcom,slim-ngd-v2.1.0";
			reg = <0 0x171c0000 0 0x2c000>;
			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;

			dmas = <&slimbam 3>, <&slimbam 4>;
			dma-names = "rx", "tx";

			iommus = <&apps_smmu 0x1806 0x0>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		lmh_cluster1: lmh@17d70800 {
			compatible = "qcom,sdm845-lmh";
			reg = <0 0x17d70800 0 0x400>;
			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
			cpus = <&CPU4>;
			qcom,lmh-temp-arm-millicelsius = <65000>;
			qcom,lmh-temp-low-millicelsius = <94500>;
			qcom,lmh-temp-high-millicelsius = <95000>;
			interrupt-controller;
			#interrupt-cells = <1>;
		};

		lmh_cluster0: lmh@17d78800 {
			compatible = "qcom,sdm845-lmh";
			reg = <0 0x17d78800 0 0x400>;
			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
			cpus = <&CPU0>;
			qcom,lmh-temp-arm-millicelsius = <65000>;
			qcom,lmh-temp-low-millicelsius = <94500>;
			qcom,lmh-temp-high-millicelsius = <95000>;
			interrupt-controller;
			#interrupt-cells = <1>;
		};

		usb_1_hsphy: phy@88e2000 {
			compatible = "qcom,sdm845-qusb2-phy", "qcom,qusb2-v2-phy";
			reg = <0 0x088e2000 0 0x400>;
			status = "disabled";
			#phy-cells = <0>;

			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "cfg_ahb", "ref";

			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;

			nvmem-cells = <&qusb2p_hstx_trim>;
		};

		usb_2_hsphy: phy@88e3000 {
			compatible = "qcom,sdm845-qusb2-phy", "qcom,qusb2-v2-phy";
			reg = <0 0x088e3000 0 0x400>;
			status = "disabled";
			#phy-cells = <0>;

			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "cfg_ahb", "ref";

			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;

			nvmem-cells = <&qusb2s_hstx_trim>;
		};

		usb_1_qmpphy: phy@88e8000 {
			compatible = "qcom,sdm845-qmp-usb3-dp-phy";
			reg = <0 0x088e8000 0 0x3000>;
			status = "disabled";

			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>,
				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>;
			clock-names = "aux",
				      "ref",
				      "com_aux",
				      "usb3_pipe",
				      "cfg_ahb";

			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#phy-cells = <1>;
		};

		usb_2_qmpphy: phy@88eb000 {
			compatible = "qcom,sdm845-qmp-usb3-uni-phy";
			reg = <0 0x088eb000 0 0x1000>;

			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_CLK>,
				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
			clock-names = "aux",
				      "cfg_ahb",
				      "ref",
				      "com_aux",
				      "pipe";
			clock-output-names = "usb3_uni_phy_pipe_clk_src";
			#clock-cells = <0>;
			#phy-cells = <0>;

			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
				 <&gcc GCC_USB3PHY_PHY_SEC_BCR>;
			reset-names = "phy",
				      "phy_phy";

			status = "disabled";
		};

		usb_1: usb@a6f8800 {
			compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
			reg = <0 0x0a6f8800 0 0x400>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			dma-ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi";

			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <150000000>;

			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc_intc 6 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc_intc 8 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc_intc 9 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "hs_phy_irq", "ss_phy_irq",
					  "dm_hs_phy_irq", "dp_hs_phy_irq";

			power-domains = <&gcc USB30_PRIM_GDSC>;

			resets = <&gcc GCC_USB30_PRIM_BCR>;

			interconnects = <&aggre2_noc MASTER_USB3_0 0 &mem_noc SLAVE_EBI1 0>,
					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			usb_1_dwc3: usb@a600000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a600000 0 0xcd00>;
				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x740 0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		usb_2: usb@a8f8800 {
			compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
			reg = <0 0x0a8f8800 0 0x400>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			dma-ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi";

			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <150000000>;

			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc_intc 7 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc_intc 10 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc_intc 11 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "hs_phy_irq", "ss_phy_irq",
					  "dm_hs_phy_irq", "dp_hs_phy_irq";

			power-domains = <&gcc USB30_SEC_GDSC>;

			resets = <&gcc GCC_USB30_SEC_BCR>;

			interconnects = <&aggre2_noc MASTER_USB3_1 0 &mem_noc SLAVE_EBI1 0>,
					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			usb_2_dwc3: usb@a800000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a800000 0 0xcd00>;
				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x760 0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_2_hsphy>, <&usb_2_qmpphy>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		venus: video-codec@aa00000 {
			compatible = "qcom,sdm845-venus-v2";
			reg = <0 0x0aa00000 0 0xff000>;
			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
			power-domains = <&videocc VENUS_GDSC>,
					<&videocc VCODEC0_GDSC>,
					<&videocc VCODEC1_GDSC>,
					<&rpmhpd SDM845_CX>;
			power-domain-names = "venus", "vcodec0", "vcodec1", "cx";
			operating-points-v2 = <&venus_opp_table>;
			clocks = <&videocc VIDEO_CC_VENUS_CTL_CORE_CLK>,
				 <&videocc VIDEO_CC_VENUS_AHB_CLK>,
				 <&videocc VIDEO_CC_VENUS_CTL_AXI_CLK>,
				 <&videocc VIDEO_CC_VCODEC0_CORE_CLK>,
				 <&videocc VIDEO_CC_VCODEC0_AXI_CLK>,
				 <&videocc VIDEO_CC_VCODEC1_CORE_CLK>,
				 <&videocc VIDEO_CC_VCODEC1_AXI_CLK>;
			clock-names = "core", "iface", "bus",
				      "vcodec0_core", "vcodec0_bus",
				      "vcodec1_core", "vcodec1_bus";
			iommus = <&apps_smmu 0x10a0 0x8>,
				 <&apps_smmu 0x10b0 0x0>;
			memory-region = <&venus_mem>;
			interconnects = <&mmss_noc MASTER_VIDEO_P0 0 &mem_noc SLAVE_EBI1 0>,
					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_VENUS_CFG 0>;
			interconnect-names = "video-mem", "cpu-cfg";

			status = "disabled";

			video-core0 {
				compatible = "venus-decoder";
			};

			video-core1 {
				compatible = "venus-encoder";
			};

			venus_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-100000000 {
					opp-hz = /bits/ 64 <100000000>;
					required-opps = <&rpmhpd_opp_min_svs>;
				};

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-320000000 {
					opp-hz = /bits/ 64 <320000000>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-380000000 {
					opp-hz = /bits/ 64 <380000000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
				};

				opp-444000000 {
					opp-hz = /bits/ 64 <444000000>;
					required-opps = <&rpmhpd_opp_nom>;
				};

				opp-533000097 {
					opp-hz = /bits/ 64 <533000097>;
					required-opps = <&rpmhpd_opp_turbo>;
				};
			};
		};

		videocc: clock-controller@ab00000 {
			compatible = "qcom,sdm845-videocc";
			reg = <0 0x0ab00000 0 0x10000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "bi_tcxo";
			#clock-cells = <1>;
			#power-domain-cells = <1>;
			#reset-cells = <1>;
		};

		camss: camss@acb3000 {
			compatible = "qcom,sdm845-camss";

			reg = <0 0x0acb3000 0 0x1000>,
				<0 0x0acba000 0 0x1000>,
				<0 0x0acc8000 0 0x1000>,
				<0 0x0ac65000 0 0x1000>,
				<0 0x0ac66000 0 0x1000>,
				<0 0x0ac67000 0 0x1000>,
				<0 0x0ac68000 0 0x1000>,
				<0 0x0acaf000 0 0x4000>,
				<0 0x0acb6000 0 0x4000>,
				<0 0x0acc4000 0 0x4000>;
			reg-names = "csid0",
				"csid1",
				"csid2",
				"csiphy0",
				"csiphy1",
				"csiphy2",
				"csiphy3",
				"vfe0",
				"vfe1",
				"vfe_lite";

			interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "csid0",
				"csid1",
				"csid2",
				"csiphy0",
				"csiphy1",
				"csiphy2",
				"csiphy3",
				"vfe0",
				"vfe1",
				"vfe_lite";

			power-domains = <&clock_camcc IFE_0_GDSC>,
				<&clock_camcc IFE_1_GDSC>,
				<&clock_camcc TITAN_TOP_GDSC>;

			clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
				<&clock_camcc CAM_CC_CPAS_AHB_CLK>,
				<&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>,
				<&clock_camcc CAM_CC_IFE_0_CSID_CLK>,
				<&clock_camcc CAM_CC_IFE_0_CSID_CLK_SRC>,
				<&clock_camcc CAM_CC_IFE_1_CSID_CLK>,
				<&clock_camcc CAM_CC_IFE_1_CSID_CLK_SRC>,
				<&clock_camcc CAM_CC_IFE_LITE_CSID_CLK>,
				<&clock_camcc CAM_CC_IFE_LITE_CSID_CLK_SRC>,
				<&clock_camcc CAM_CC_CSIPHY0_CLK>,
				<&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>,
				<&clock_camcc CAM_CC_CSI0PHYTIMER_CLK_SRC>,
				<&clock_camcc CAM_CC_CSIPHY1_CLK>,
				<&clock_camcc CAM_CC_CSI1PHYTIMER_CLK>,
				<&clock_camcc CAM_CC_CSI1PHYTIMER_CLK_SRC>,
				<&clock_camcc CAM_CC_CSIPHY2_CLK>,
				<&clock_camcc CAM_CC_CSI2PHYTIMER_CLK>,
				<&clock_camcc CAM_CC_CSI2PHYTIMER_CLK_SRC>,
				<&clock_camcc CAM_CC_CSIPHY3_CLK>,
				<&clock_camcc CAM_CC_CSI3PHYTIMER_CLK>,
				<&clock_camcc CAM_CC_CSI3PHYTIMER_CLK_SRC>,
				<&gcc GCC_CAMERA_AHB_CLK>,
				<&gcc GCC_CAMERA_AXI_CLK>,
				<&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
				<&clock_camcc CAM_CC_SOC_AHB_CLK>,
				<&clock_camcc CAM_CC_IFE_0_AXI_CLK>,
				<&clock_camcc CAM_CC_IFE_0_CLK>,
				<&clock_camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
				<&clock_camcc CAM_CC_IFE_0_CLK_SRC>,
				<&clock_camcc CAM_CC_IFE_1_AXI_CLK>,
				<&clock_camcc CAM_CC_IFE_1_CLK>,
				<&clock_camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
				<&clock_camcc CAM_CC_IFE_1_CLK_SRC>,
				<&clock_camcc CAM_CC_IFE_LITE_CLK>,
				<&clock_camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
				<&clock_camcc CAM_CC_IFE_LITE_CLK_SRC>;
			clock-names = "camnoc_axi",
				"cpas_ahb",
				"cphy_rx_src",
				"csi0",
				"csi0_src",
				"csi1",
				"csi1_src",
				"csi2",
				"csi2_src",
				"csiphy0",
				"csiphy0_timer",
				"csiphy0_timer_src",
				"csiphy1",
				"csiphy1_timer",
				"csiphy1_timer_src",
				"csiphy2",
				"csiphy2_timer",
				"csiphy2_timer_src",
				"csiphy3",
				"csiphy3_timer",
				"csiphy3_timer_src",
				"gcc_camera_ahb",
				"gcc_camera_axi",
				"slow_ahb_src",
				"soc_ahb",
				"vfe0_axi",
				"vfe0",
				"vfe0_cphy_rx",
				"vfe0_src",
				"vfe1_axi",
				"vfe1",
				"vfe1_cphy_rx",
				"vfe1_src",
				"vfe_lite",
				"vfe_lite_cphy_rx",
				"vfe_lite_src";

			iommus = <&apps_smmu 0x0808 0x0>,
				 <&apps_smmu 0x0810 0x8>,
				 <&apps_smmu 0x0c08 0x0>,
				 <&apps_smmu 0x0c10 0x8>;

			status = "disabled";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
				};

				port@1 {
					reg = <1>;
				};

				port@2 {
					reg = <2>;
				};

				port@3 {
					reg = <3>;
				};
			};
		};

		cci: cci@ac4a000 {
			compatible = "qcom,sdm845-cci", "qcom,msm8996-cci";
			#address-cells = <1>;
			#size-cells = <0>;

			reg = <0 0x0ac4a000 0 0x4000>;
			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
			power-domains = <&clock_camcc TITAN_TOP_GDSC>;

			clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
				<&clock_camcc CAM_CC_SOC_AHB_CLK>,
				<&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
				<&clock_camcc CAM_CC_CPAS_AHB_CLK>,
				<&clock_camcc CAM_CC_CCI_CLK>,
				<&clock_camcc CAM_CC_CCI_CLK_SRC>;
			clock-names = "camnoc_axi",
				"soc_ahb",
				"slow_ahb_src",
				"cpas_ahb",
				"cci",
				"cci_src";

			assigned-clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
				<&clock_camcc CAM_CC_CCI_CLK>;
			assigned-clock-rates = <80000000>, <37500000>;

			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&cci0_default &cci1_default>;
			pinctrl-1 = <&cci0_sleep &cci1_sleep>;

			status = "disabled";

			cci_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		clock_camcc: clock-controller@ad00000 {
			compatible = "qcom,sdm845-camcc";
			reg = <0 0x0ad00000 0 0x10000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "bi_tcxo";
		};

		mdss: display-subsystem@ae00000 {
			compatible = "qcom,sdm845-mdss";
			reg = <0 0x0ae00000 0 0x1000>;
			reg-names = "mdss";

			power-domains = <&dispcc MDSS_GDSC>;

			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
			clock-names = "iface", "core";

			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <1>;

			interconnects = <&mmss_noc MASTER_MDP0 0 &mem_noc SLAVE_EBI1 0>,
					<&mmss_noc MASTER_MDP1 0 &mem_noc SLAVE_EBI1 0>;
			interconnect-names = "mdp0-mem", "mdp1-mem";

			iommus = <&apps_smmu 0x880 0x8>,
			         <&apps_smmu 0xc80 0x8>;

			status = "disabled";

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			mdss_mdp: display-controller@ae01000 {
				compatible = "qcom,sdm845-dpu";
				reg = <0 0x0ae01000 0 0x8f000>,
				      <0 0x0aeb0000 0 0x2008>;
				reg-names = "mdp", "vbif";

				clocks = <&gcc GCC_DISP_AXI_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_AXI_CLK>,
					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				clock-names = "gcc-bus", "iface", "bus", "core", "vsync";

				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				assigned-clock-rates = <19200000>;
				operating-points-v2 = <&mdp_opp_table>;
				power-domains = <&rpmhpd SDM845_CX>;

				interrupt-parent = <&mdss>;
				interrupts = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dpu_intf0_out: endpoint {
							remote-endpoint = <&dp_in>;
						};
					};

					port@1 {
						reg = <1>;
						dpu_intf1_out: endpoint {
							remote-endpoint = <&mdss_dsi0_in>;
						};
					};

					port@2 {
						reg = <2>;
						dpu_intf2_out: endpoint {
							remote-endpoint = <&mdss_dsi1_in>;
						};
					};
				};

				mdp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-19200000 {
						opp-hz = /bits/ 64 <19200000>;
						required-opps = <&rpmhpd_opp_min_svs>;
					};

					opp-171428571 {
						opp-hz = /bits/ 64 <171428571>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-344000000 {
						opp-hz = /bits/ 64 <344000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-430000000 {
						opp-hz = /bits/ 64 <430000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss_dp: displayport-controller@ae90000 {
				status = "disabled";
				compatible = "qcom,sdm845-dp";

				reg = <0 0x0ae90000 0 0x200>,
				      <0 0x0ae90200 0 0x200>,
				      <0 0x0ae90400 0 0x600>,
				      <0 0x0ae90a00 0 0x600>,
				      <0 0x0ae91000 0 0x600>;

				interrupt-parent = <&mdss>;
				interrupts = <12>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
				clock-names = "core_iface", "core_aux", "ctrl_link",
					      "ctrl_link_iface", "stream_pixel";
				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
				assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
							 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
				phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>;
				phy-names = "dp";

				operating-points-v2 = <&dp_opp_table>;
				power-domains = <&rpmhpd SDM845_CX>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;
					port@0 {
						reg = <0>;
						dp_in: endpoint {
							remote-endpoint = <&dpu_intf0_out>;
						};
					};

					port@1 {
						reg = <1>;
						dp_out: endpoint { };
					};
				};

				dp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-162000000 {
						opp-hz = /bits/ 64 <162000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss_dsi0: dsi@ae94000 {
				compatible = "qcom,sdm845-dsi-ctrl",
					     "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae94000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";
				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;

				operating-points-v2 = <&dsi_opp_table>;
				power-domains = <&rpmhpd SDM845_CX>;

				phys = <&mdss_dsi0_phy>;

				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi0_in: endpoint {
							remote-endpoint = <&dpu_intf1_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi0_out: endpoint {
						};
					};
				};
			};

			mdss_dsi0_phy: phy@ae94400 {
				compatible = "qcom,dsi-phy-10nm";
				reg = <0 0x0ae94400 0 0x200>,
				      <0 0x0ae94600 0 0x280>,
				      <0 0x0ae94a00 0 0x1e0>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};

			mdss_dsi1: dsi@ae96000 {
				compatible = "qcom,sdm845-dsi-ctrl",
					     "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae96000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <5>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";
				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;

				operating-points-v2 = <&dsi_opp_table>;
				power-domains = <&rpmhpd SDM845_CX>;

				phys = <&mdss_dsi1_phy>;

				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi1_in: endpoint {
							remote-endpoint = <&dpu_intf2_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi1_out: endpoint {
						};
					};
				};
			};

			mdss_dsi1_phy: phy@ae96400 {
				compatible = "qcom,dsi-phy-10nm";
				reg = <0 0x0ae96400 0 0x200>,
				      <0 0x0ae96600 0 0x280>,
				      <0 0x0ae96a00 0 0x10e>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};
		};

		gpu: gpu@5000000 {
			compatible = "qcom,adreno-630.2", "qcom,adreno";

			reg = <0 0x05000000 0 0x40000>, <0 0x509e000 0 0x10>;
			reg-names = "kgsl_3d0_reg_memory", "cx_mem";

			/*
			 * Look ma, no clocks! The GPU clocks and power are
			 * controlled entirely by the GMU
			 */

			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;

			iommus = <&adreno_smmu 0>;

			operating-points-v2 = <&gpu_opp_table>;

			qcom,gmu = <&gmu>;

			interconnects = <&mem_noc MASTER_GFX3D 0 &mem_noc SLAVE_EBI1 0>;
			interconnect-names = "gfx-mem";

			status = "disabled";

			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-710000000 {
					opp-hz = /bits/ 64 <710000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					opp-peak-kBps = <7216000>;
				};

				opp-675000000 {
					opp-hz = /bits/ 64 <675000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					opp-peak-kBps = <7216000>;
				};

				opp-596000000 {
					opp-hz = /bits/ 64 <596000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					opp-peak-kBps = <6220000>;
				};

				opp-520000000 {
					opp-hz = /bits/ 64 <520000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					opp-peak-kBps = <6220000>;
				};

				opp-414000000 {
					opp-hz = /bits/ 64 <414000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					opp-peak-kBps = <4068000>;
				};

				opp-342000000 {
					opp-hz = /bits/ 64 <342000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					opp-peak-kBps = <2724000>;
				};

				opp-257000000 {
					opp-hz = /bits/ 64 <257000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					opp-peak-kBps = <1648000>;
				};
			};
		};

		adreno_smmu: iommu@5040000 {
			compatible = "qcom,sdm845-smmu-v2", "qcom,adreno-smmu", "qcom,smmu-v2";
			reg = <0 0x05040000 0 0x10000>;
			#iommu-cells = <1>;
			#global-interrupts = <2>;
			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 364 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 365 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 366 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 367 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 368 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 369 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 370 IRQ_TYPE_EDGE_RISING>,
				     <GIC_SPI 371 IRQ_TYPE_EDGE_RISING>;
			clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
			         <&gcc GCC_GPU_CFG_AHB_CLK>;
			clock-names = "bus", "iface";

			power-domains = <&gpucc GPU_CX_GDSC>;
		};

		gmu: gmu@506a000 {
			compatible = "qcom,adreno-gmu-630.2", "qcom,adreno-gmu";

			reg = <0 0x0506a000 0 0x30000>,
			      <0 0x0b280000 0 0x10000>,
			      <0 0x0b480000 0 0x10000>;
			reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq";

			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hfi", "gmu";

			clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
			         <&gpucc GPU_CC_CXO_CLK>,
				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
			clock-names = "gmu", "cxo", "axi", "memnoc";

			power-domains = <&gpucc GPU_CX_GDSC>,
					<&gpucc GPU_GX_GDSC>;
			power-domain-names = "cx", "gx";

			iommus = <&adreno_smmu 5>;

			operating-points-v2 = <&gmu_opp_table>;

			status = "disabled";

			gmu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-400000000 {
					opp-hz = /bits/ 64 <400000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
				};

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
				};
			};
		};

		dispcc: clock-controller@af00000 {
			compatible = "qcom,sdm845-dispcc";
			reg = <0 0x0af00000 0 0x10000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_DISP_GPLL0_CLK_SRC>,
				 <&gcc GCC_DISP_GPLL0_DIV_CLK_SRC>,
				 <&mdss_dsi0_phy 0>,
				 <&mdss_dsi0_phy 1>,
				 <&mdss_dsi1_phy 0>,
				 <&mdss_dsi1_phy 1>,
				 <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
				 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
			clock-names = "bi_tcxo",
				      "gcc_disp_gpll0_clk_src",
				      "gcc_disp_gpll0_div_clk_src",
				      "dsi0_phy_pll_out_byteclk",
				      "dsi0_phy_pll_out_dsiclk",
				      "dsi1_phy_pll_out_byteclk",
				      "dsi1_phy_pll_out_dsiclk",
				      "dp_link_clk_divsel_ten",
				      "dp_vco_divided_clk_src_mux";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		pdc_intc: interrupt-controller@b220000 {
			compatible = "qcom,sdm845-pdc", "qcom,pdc";
			reg = <0 0x0b220000 0 0x30000>;
			qcom,pdc-ranges = <0 480 94>, <94 609 15>, <115 630 7>;
			#interrupt-cells = <2>;
			interrupt-parent = <&intc>;
			interrupt-controller;
		};

		pdc_reset: reset-controller@b2e0000 {
			compatible = "qcom,sdm845-pdc-global";
			reg = <0 0x0b2e0000 0 0x20000>;
			#reset-cells = <1>;
		};

		tsens0: thermal-sensor@c263000 {
			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
			reg = <0 0x0c263000 0 0x1ff>, /* TM */
			      <0 0x0c222000 0 0x1ff>; /* SROT */
			#qcom,sensors = <13>;
			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens1: thermal-sensor@c265000 {
			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
			reg = <0 0x0c265000 0 0x1ff>, /* TM */
			      <0 0x0c223000 0 0x1ff>; /* SROT */
			#qcom,sensors = <8>;
			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		aoss_reset: reset-controller@c2a0000 {
			compatible = "qcom,sdm845-aoss-cc";
			reg = <0 0x0c2a0000 0 0x31000>;
			#reset-cells = <1>;
		};

		aoss_qmp: power-management@c300000 {
			compatible = "qcom,sdm845-aoss-qmp", "qcom,aoss-qmp";
			reg = <0 0x0c300000 0 0x400>;
			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
			mboxes = <&apss_shared 0>;

			#clock-cells = <0>;

			cx_cdev: cx {
				#cooling-cells = <2>;
			};

			ebi_cdev: ebi {
				#cooling-cells = <2>;
			};
		};

		sram@c3f0000 {
			compatible = "qcom,sdm845-rpmh-stats";
			reg = <0 0x0c3f0000 0 0x400>;
		};

		spmi_bus: spmi@c440000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0 0x0c440000 0 0x1100>,
			      <0 0x0c600000 0 0x2000000>,
			      <0 0x0e600000 0 0x100000>,
			      <0 0x0e700000 0 0xa0000>,
			      <0 0x0c40a000 0 0x26000>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		sram@146bf000 {
			compatible = "qcom,sdm845-imem", "syscon", "simple-mfd";
			reg = <0 0x146bf000 0 0x1000>;

			#address-cells = <1>;
			#size-cells = <1>;

			ranges = <0 0 0x146bf000 0x1000>;

			pil-reloc@94c {
				compatible = "qcom,pil-reloc-info";
				reg = <0x94c 0xc8>;
			};
		};

		apps_smmu: iommu@15000000 {
			compatible = "qcom,sdm845-smmu-500", "arm,mmu-500";
			reg = <0 0x15000000 0 0x80000>;
			#iommu-cells = <2>;
			#global-interrupts = <1>;
			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
		};

		lpasscc: clock-controller@17014000 {
			compatible = "qcom,sdm845-lpasscc";
			reg = <0 0x17014000 0 0x1f004>, <0 0x17300000 0 0x200>;
			reg-names = "cc", "qdsp6ss";
			#clock-cells = <1>;
			status = "disabled";
		};

		gladiator_noc: interconnect@17900000 {
			compatible = "qcom,sdm845-gladiator-noc";
			reg = <0 0x17900000 0 0xd080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		watchdog@17980000 {
			compatible = "qcom,apss-wdt-sdm845", "qcom,kpss-wdt";
			reg = <0 0x17980000 0 0x1000>;
			clocks = <&sleep_clk>;
			interrupts = <GIC_SPI 0 IRQ_TYPE_EDGE_RISING>;
		};

		apss_shared: mailbox@17990000 {
			compatible = "qcom,sdm845-apss-shared";
			reg = <0 0x17990000 0 0x1000>;
			#mbox-cells = <1>;
		};

		apps_rsc: rsc@179c0000 {
			label = "apps_rsc";
			compatible = "qcom,rpmh-rsc";
			reg = <0 0x179c0000 0 0x10000>,
			      <0 0x179d0000 0 0x10000>,
			      <0 0x179e0000 0 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS  2>,
					  <SLEEP_TCS   3>,
					  <WAKE_TCS    3>,
					  <CONTROL_TCS 1>;
			power-domains = <&CLUSTER_PD>;

			apps_bcm_voter: bcm-voter {
				compatible = "qcom,bcm-voter";
			};

			rpmhcc: clock-controller {
				compatible = "qcom,sdm845-rpmh-clk";
				#clock-cells = <1>;
				clock-names = "xo";
				clocks = <&xo_board>;
			};

			rpmhpd: power-controller {
				compatible = "qcom,sdm845-rpmhpd";
				#power-domain-cells = <1>;
				operating-points-v2 = <&rpmhpd_opp_table>;

				rpmhpd_opp_table: opp-table {
					compatible = "operating-points-v2";

					rpmhpd_opp_ret: opp1 {
						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
					};

					rpmhpd_opp_min_svs: opp2 {
						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
					};

					rpmhpd_opp_low_svs: opp3 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					};

					rpmhpd_opp_svs: opp4 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					};

					rpmhpd_opp_svs_l1: opp5 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					};

					rpmhpd_opp_nom: opp6 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					};

					rpmhpd_opp_nom_l1: opp7 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					};

					rpmhpd_opp_nom_l2: opp8 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
					};

					rpmhpd_opp_turbo: opp9 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					};

					rpmhpd_opp_turbo_l1: opp10 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					};
				};
			};
		};

		intc: interrupt-controller@17a00000 {
			compatible = "arm,gic-v3";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			#interrupt-cells = <3>;
			interrupt-controller;
			reg = <0 0x17a00000 0 0x10000>,     /* GICD */
			      <0 0x17a60000 0 0x100000>;    /* GICR * 8 */
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;

			msi-controller@17a40000 {
				compatible = "arm,gic-v3-its";
				msi-controller;
				#msi-cells = <1>;
				reg = <0 0x17a40000 0 0x20000>;
				status = "disabled";
			};
		};

		slimbam: dma-controller@17184000 {
			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
			qcom,controlled-remotely;
			reg = <0 0x17184000 0 0x2a000>;
			num-channels = <31>;
			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
			#dma-cells = <1>;
			qcom,ee = <1>;
			qcom,num-ees = <2>;
			iommus = <&apps_smmu 0x1806 0x0>;
		};

		timer@17c90000 {
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0 0 0x20000000>;
			compatible = "arm,armv7-timer-mem";
			reg = <0 0x17c90000 0 0x1000>;

			frame@17ca0000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17ca0000 0x1000>,
				      <0x17cb0000 0x1000>;
			};

			frame@17cc0000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17cc0000 0x1000>;
				status = "disabled";
			};

			frame@17cd0000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17cd0000 0x1000>;
				status = "disabled";
			};

			frame@17ce0000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17ce0000 0x1000>;
				status = "disabled";
			};

			frame@17cf0000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17cf0000 0x1000>;
				status = "disabled";
			};

			frame@17d00000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17d00000 0x1000>;
				status = "disabled";
			};

			frame@17d10000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17d10000 0x1000>;
				status = "disabled";
			};
		};

		osm_l3: interconnect@17d41000 {
			compatible = "qcom,sdm845-osm-l3", "qcom,osm-l3";
			reg = <0 0x17d41000 0 0x1400>;

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
			clock-names = "xo", "alternate";

			#interconnect-cells = <1>;
		};

		cpufreq_hw: cpufreq@17d43000 {
			compatible = "qcom,sdm845-cpufreq-hw", "qcom,cpufreq-hw";
			reg = <0 0x17d43000 0 0x1400>, <0 0x17d45800 0 0x1400>;
			reg-names = "freq-domain0", "freq-domain1";

			interrupts-extended = <&lmh_cluster0 0>, <&lmh_cluster1 0>;

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
			clock-names = "xo", "alternate";

			#freq-domain-cells = <1>;
			#clock-cells = <1>;
		};

		wifi: wifi@18800000 {
			compatible = "qcom,wcn3990-wifi";
			status = "disabled";
			reg = <0 0x18800000 0 0x800000>;
			reg-names = "membase";
			memory-region = <&wlan_msa_mem>;
			clock-names = "cxo_ref_clk_pin";
			clocks = <&rpmhcc RPMH_RF_CLK2>;
			interrupts =
				<GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
				<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
			iommus = <&apps_smmu 0x0040 0x1>;
		};
	};

	sound: sound {
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 1>;

			trips {
				cpu0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 2>;

			trips {
				cpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 3>;

			trips {
				cpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 4>;

			trips {
				cpu3_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu4-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 7>;

			trips {
				cpu4_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu5-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 8>;

			trips {
				cpu5_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu6-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 9>;

			trips {
				cpu6_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 10>;

			trips {
				cpu7_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		aoss0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 0>;

			trips {
				aoss0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		cluster0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 5>;

			trips {
				cluster0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
				cluster0_crit: cluster0_crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cluster1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 6>;

			trips {
				cluster1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
				cluster1_crit: cluster1_crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		gpu-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 11>;

			trips {
				gpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		gpu-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 12>;

			trips {
				gpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		aoss1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 0>;

			trips {
				aoss1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		q6-modem-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 1>;

			trips {
				q6_modem_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 2>;

			trips {
				mem_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		wlan-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 3>;

			trips {
				wlan_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		q6-hvx-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 4>;

			trips {
				q6_hvx_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		camera-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 5>;

			trips {
				camera_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		video-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 6>;

			trips {
				video_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		modem-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 7>;

			trips {
				modem_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
	};
};